Search Documents

By N N. Viswanathan, D Kumar, S Kumar

In secondary steelmaking, calcium treatment is practised to modify the solid alumina or spinel inclusions into liquid or partially liquid calcium aluminates. It has been seen that the dissolved calcium reacts with sulfur or oxygen present in the steel to form CaS or CaO type of transient inclusions. Post-calcium treatment these transient inclusions further react with pre-existing alumina or spinel inclusions and modify them. In addition, direct modification of pre-existing inclusions is also reported in the literature. In the present study, laboratory-scale induction furnace-based experiments are carried out to melt electrolytic iron in an alumina crucible followed by deoxidation with aluminium. The CaS-based composite material, prepared in-house, is added after the aluminium deoxidation to study the stability of CaS at the steelmaking temperature. Multiple steel samples were also taken to track the dissociation of CaS by means of sulfur pick-up in steel. Additionally, inclusion analysis of these steel samples was also performed to track changes in the chemical composition of inclusions in response to CaS addition. It has been seen that the CaS dissociates leading to a gradual pick-up of sulfur in steel. The scanning electron microscope – energy dispersive X-ray spectroscopy (SEM-EDS) analysis reveals that the alumina crucible and floated alumina inclusions are modified into calcium aluminates and the extent of modification depends on the contact time of CaS with the two sources of alumina mentioned earlier. However, the modification of alumina inclusions in the bulk steel did not occur during these experiments.

Jun 19, 2024

By P Nissen, T Jenke, M Ralph, M Cattani, M Quinlan

The West Australian Government hold an annual ‘Mines Safety Roadshow’ around the State’s regions and the capital city, Perth. Each year presenters provide an update on legislation and safetyrelated themes. A recurring theme is the mining industry fatality rate. Professor Michael Quinlan’s ‘Ten Pathways to Death and Disaster’ (Quinlan, 2014) has been referenced regularly to assist in structuring workshops and conversations concerning fatality prevention in the mining industry. The ‘Ten Pathways’ are the outcome of an analysis of fatal injuries in the mining industry, which identified a series of common themes to the fatalities: Pathway 1: Design, engineering, technical and maintenance flaws. Pathway 2: Prior warnings or causes for alarm ignored. Pathway 3: Failures in risk assessment. Pathway 4: Failures in management systems and hazard management plans. Pathway 5: Failures in auditing. Pathway 6: Economic pressures compromising safety. Pathway 7: Failures in regulatory oversight and inspection. Pathway 8: Worker and others expressing concern prior to the incident. Pathway 9: Poor management – worker communication and trust. Pathway 10: Emergency and rescue resources and procedures. To determine a fatality risk profile we asked participants at the Mines Safety Roadshows to indicate their perception of their employer’s performance in each of the Ten Pathways. We administered the questionnaire at the Mines Safety Roadshows in 2017, 2018, 2019 and 2023. In this paper, we report on the results of the questionnaires, and suggest how organisations can improve their fatality risk score.

Apr 16, 2024

By M Zanin, E Chan, D Xu

An experimental design has been developed to investigate the relative influence of distinct pulp and environmental properties on froth stability in the flotation of a typical porphyry copper ore. In particular, factors such as frother and collector type, feed particle size (P80), solids per cent, composition (chalcopyrite and pyrite content), as well as grinding environment (mild steel versus stainless steel, high and low pH) have been varied in a controlled manner, and the resulting froth stability evaluated. A previously developed froth stability column, based on the Bikerman approach, was used to measure the froth height and half-life in each test. The relative effect of each factor is presented here on a comparative basis. It is shown that frother type is the most important factor, with marked difference in froth stability when switching from methyl isobutyl carbinol (MIBC) to glycol based frothers. Solids per cent and particle size also play a significant role. The grinding environment had lesser effect on the resulting froth stability, although mild steel grinding gave higher froth stability compared to stainless steel grinding. The experimental evidence supports the hypothesis that in porphyry copper flotation the grinding environment influences surfaces oxidation, pyrite activation and the extent of hydrophobic particles reporting to the froth phase. This has an indirect effect on the resulting froth stability, which is however small if compared to the other factors. This work is still in progress, and extension to other mineral systems is planned. However, some insights are offered to operators on the parameters which are more likely to have an impact on froth stability in copper flotation plants.CITATION:Zanin, M, Chan, E and Xu, D, 2014. Empirical evaluation of factors affecting froth stability in copper flotation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 193–200 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Pratt V

The economic, social and political environment of the mining and minerals industries is, as we all know, volatile and affected by constantly changing international forces. In addition, the outcome of negotiations with overseas customers is often uncertain for long periods, or even unfavourable. The industries and companies represented at this Conference are in an arena of high competition, risk taking and enormous capital outlay. They are industries which our overseas markets (rightly or wrongly) have criticised for industrial relations problems, unreliable production and uncertain deliveries. They are industries which have an urgent need to be cost effective and competitive at all levels of activity.A critical factor in the mining and metallurgy industries is, therefore, its human resources and its human resource management. It requires the full use of available talent, innovation, skills and qualifications within its workforce, and the appropriate management of these resources.

Jan 1, 1985

By R Araya, G Harbort, D R. Seaman, L Huynh, P D. Munro

In today’s operating environment many conventional cleaner circuits struggle to produce final grade concentrate with acceptable levels of non-sulfide gangue and/or penalty elements. This is primarily due to poor selectivity and the entrainment of gangue, and is further exacerbated by the processing of lower grade ores with more complex mineralogy that require finer grinding for liberation. In new concentrators, the standard approach to cleaner circuit design is to define the number of stages of mechanical cells required to achieve the desired concentrate grade. Residence time is the primary factor to size cells and to determine the number of cells required to attain target recovery. While it is required for recovery, a bank of mechanical cells is not the ideal solution to maximise concentrate grade. Relatively coarse bubble size means slow flotation of fines, requiring long residence times. The combination of long residence times and no froth washing means higher entrainment as the pulp becomes more barren and froth stability decreases down a bank.In recent years, the Jameson Cell technology has been retrofitted into a number of concentrators around the world to solve both cleaner circuit capacity and concentrate grade issues. Jameson Cells have been installed at the head of conventional cleaner circuits to produce final grade concentrate in a single step of flotation using a single cell (referred to here as ‘cleaner scalping’ duty). The experience gained from these installations has provided the platform for the design of improved and simpler cleaner circuits that will perform better and be more robust to operate. This paper analyses traditional cleaner circuit designs and explains the philosophy behind new hybrid cleaner circuits, which use Jameson Cells to produce final concentrate and mechanical cells for a ‘cleaner scavenger’ duty. The advantages of the new cleaner circuit design are demonstrated by a case study from an operating plant. Engineering studies show that the better metallurgical performance can be achieved with less equipment than conventional cleaning designs, reducing capital cost, operating cost, and with more than 30 per cent energy savings.Finally, the paper describes simple modifications to the standard laboratory flotation test procedures which accurately simulate this new cleaner circuit using routine equipment.CITATION:Huynh, L, Araya, R, Seaman, D R, Harbort, G and Munro, P D, 2014. Improved cleaner circuit design for better performance using the Jameson Cell, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 141–152 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

Our ultimate resources come from the Sun and the Earth System. At this time we face a world crisis in energy, water and soil resources. Global pollution problems are increasing in almost all nations. There is an urgent need to use our vast knowledge with a new wisdom and this requires new integrated teams of experts to provide the best alternatives for the needed new development problems. These teams must include economists, engineers and a broad spectrum of scientists. Today it is possible to produce clean energy, stop soil erosion, clean water and reduce and use wastes of many types.

Jan 1, 1995

By Balint F

The Izok massive sulphide deposits are located in the Northwest Territories of the remote western Canadian Arctic. Together they represent one of the highest grade undeveloped zinc-copper resources in North America. Metall Mining Corporation is presently engaged in a feasibility study on developing the Izok property as well as actively exploring for additional reserves. The Izok deposits are Archean-aged, volcanogenic massive sulphide (VMS) bodies hosted within and near the top of a thick sequence of predominantly felsic pyroclastic rocks. The hangingwall package includes additional felsic volcanoclastics, dacitic and basaltic flows, thin sulphide-rich iron formations, and turbiditic sediments. The felsic volcanics are intruded by syn- to late-hydrothermal dacitic dykes and sills and post-hydrothermal gabbroic dykes and sills. Both intrusives are interpreted to be volcanic feeders to overlying flows. All lithologies are cut by much later irregular granitic pegmatite dykes and regionally metamorphosed to pyroxene homfels grade. The deposits occur within a large kilometre-scale soda-depleted alteration zone. The immediate footwall and hangingwall rocks to the deposits are characterised by zones of muscovite-biotite (with or without sillimanite), lesser chlorite-biotite-cordierite (with or without anthophyllite), and locally intense silicificified and albitised zones. All lithologies have been affected by a later calcic metasomatic alteration. As currently defined, the Izok Zn-Cu-Pb-Ag deposits comprise a cluster of four complexly-zoned composite lenses: the Northwest, North, Central, and newly discovered Inukshuk deposits. The first three deposits are amenable to open pit mining while development of the Inukshuk deposit will require underground methods. The combined mineral inventory of the Northwest, North, Central and Inukshuk deposits at present totals 15.6 million tonnes with a grade of 2.4 per cent Cu, 13.8 per cent Zn, 1.4 per cent Pb, and 74.6 g/t Ag.

Jan 1, 1993

By Barlow S

The Kelian Gold mine project won two excellence awards from the Victorian Division of the Institution of Engineers, Australia. It was a challenging project, fast tracked in a remote and inhospitable tropical environment. The creation of a profitable and efficient mine was a significant engineering and project management achievement. The difficulties encountered and the way they were managed provide valuable lessons. These include the importance of sufficiently detailed engineering in all aspects of the job to enable the best estimates possible to be prepared during feasibility studies, the need to prepare the project scope and execution plan with disciplined and rigorous attention to detail by a highly experienced team and the value of identifying, assessing and mitigating risk and uncertainty during execution. The practical benefits of applying these lessons were demonstrated in the successful management of technical uncertainty on the recent diversion of the Kelian River to allow the expansion of the Kelian mine.

Jan 1, 1997

By Yaniuk DW

The sampling of non-ferrous concentrates from trucks and trains has long been carried out either manually or by automatic spears. Very little use has been made of conventional sampling systems for sampling concentrates at transfer points, or cross-belt samplers for sampling from the belt as the concentrate moves along the conveyor.Due to the high value of base metal concentrates and the often extremely heterogeneous nature of the material it is imperative that the sampling procedures adopted are accurate and precise. The basic principle that all particles in the stream have an equal opportunity to be included in the final sample is not fulfilled by accepted traditional concentrate sampling procedures such as the spearing of wagons, trucks or streams. This may lead to significant bias being introduced into the final sample.Consequently, the application of correct sampling procedures, either with conventional cross-stream samplers or the newer cross-belt samplers, is of prime importance.SGS Australia has recently installed a number of cross-belt samplers for the sampling of base metal concentrates both in Australia and overseas. The application of these samplers will be discussed with emphasis on the benefits of their use.

Jan 1, 1976

By Cai S, Zhou C

The requirement of mineral resources is increasing as the economy is continually increasing in China. The mining practices of various complex sulphide deposits and precious metal deposits, and the treatment of mine tailings and other industrial solid wastes, have greatly improved fill quality in the metal mines. From early-1980s, high density slurry fill, paste fill of total tailings, low density slurry fill with addition of silicate gelling agent, etc has been studied and applied, and some progress has been achieved. Today, mine tailings, slag and power plant ash are widely used as fill materials in mining. A number of cemented fill mines equipped with large capacity trackless mining machines are in production. Recently, The 3rd Chinese National Symposium on Mining with Backfill, 1995 has been held, the progress of fill technology in mines has been exchanged and summarised. In the paper, some aspects of fill technology used in the metal mines of China are briefly introduced and some applications of fill research work are presented.

Jan 1, 1998

By Fukuichi K, Matsukawa H, Nakagawa M

The Myojin Tunnel, located on the Shikoku Expressway being constructed by the Japan Highway Public Corporation, is 3,770 m long with a cross sectional area of 80 m2. Kajima Corporation, the contractor for the northern construction section of this tunnel, adopted here its newly developed "mini-bench" method of excavation. The objectives of this method were 1. to be able to perform all tunnelling operations using the whole cross sectional area of the tunnel under any ground conditions, and 2. to be able to vary the length of the mini-bench within the range of 0 to 7 m according to ground conditions. In order to achieve these objectives, original, sophisticated equipment was developed and employed in the work. One of the newly developed machines is a special jumbo, a hydraulic crawler jumbo with five rotary type booms. This machine is capable of accommodating variation in the length of the mini-bench accompanying changes in ground conditions and is equipped with a special mechanism by which the positions of the booms can be controlled by means of hydraulic cylinders. Also developed was a shotcrete robot for use with the mini-bench method which has the control board near the shotcrete nozzle for close control of application.

Jan 1, 1987

By M Campbell, A Jeffcoate, J-C Vannay, B Perriaux

Phyllite waste rock at the Simandou Pic de Fon and Oueleba Iron Ore deposits (Guinea, West Africa) variably weather to form clay-rich rocks. This weathering modifies the mineralogical, geochemical and mechanical properties of the phyllites. Final pit walls will largely be formed in phyllite, so it is critical that the slope design takes account of the distribution and variability of weathering within this material. Phyllite intact material strength has been correlated with geochemistry (ie mineralogy) facilitating the establishment of domains of intact rock strength (IRS). In order to calibrate this geochemically-based strength model, core from diamond drilling (DD), comprising a variety of phyllite material types (from soft clay to moderate strength rock), was geotechnically logged to assess intact strength; further validation was achieved by uniaxial compression (UCS) testing and point load tests (PLT). The correlation between geochemistry and strength offers a potentially powerful tool for differentiating basic mechanical properties of the rock mass, especially at Simandou where a significant proportion of the resource drilling is done by reverse circulation (RC). Unlike DD, reliable measurements of material strength from RC samples can prove difficult, especially in clay-rich material. Therefore, gaining information from routine geochemical assay results, independent of the sampleÆs physical integrity, is a valuable and cost-effective source of reliable empirical data. Data acquired using this approach provides an opportunity to develop strength domains, which are integrated into mine planning block models. In combination with other geotechnical characteristics, this can be a valuable input to the development of geotechnical models. This technique has allowed spatially representative rock strength data to be derived and offers the potential for optimising pit slope angles in areas where hitherto conservative design criteria had been assumed.CITATION:Jeffcoate, A, Campbell, M, Vannay, J-C and Perriaux, B, 2013. Modelling intact rock strength of clay-rich rocks with geochemistry at the Simandou iron ore deposit, Guinea, West Africa, in Proceedings Iron Ore 2013 , pp 193-202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By I Canbulat, J Oh, A Mcquillan, D Payne

This paper presents a new risk assessment tool for coal mine excavated slopes. This new empirical-statistical Slope Stability Assessment Methodology (SSAM) is intended for use by geotechnical engineers at both the design review and operational stages of a mine’s life to categorise the risk of an excavated coal mine slope. A likelihood of failure is determined using a new slope stability classification system for excavated coal mine slopes developed using a database of 119 intact and failed case studies sourced from open cut coal mines in Australia. Consequence of failure is based on slope height and stand-off distance at the toe of the excavated slope. Results are presented in a new risk matrix, with slope risk being divided into low, medium and high categories. The SSAM is put forward as a new risk assessment tool to assess the potential for, and consequence of, excavated coal mine slope failure. Unlike existing classification systems, assumptions about the likely failure mode or mechanism are not required. Instead, the SSAM applies an approach which compares the conditions present within the excavated slope face, with the known past performance of slopes with similar geotechnical and geometrical conditions, to estimate the slope’s propensity for failure. The SSAM is novel in that it considers the depositional history of strata in an excavated slope and how this sequence affects slope stability. It is further novel in that it does not require explicit measurements of intact rock, rock mass and/or defect strength to rapidly calculate a slope’s likelihood of failure and overall risk. Ratings can be determined entirely from visual observations of the excavated slope face. The new SSAM is designed to be used in conjunction with existing slope stability assessment tools. CITATION:Mcquillan, A, Canbulat, I, Payne, D and Oh, J, 2018. New risk assessment method for coal mine excavated slopes, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 473–495 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

The Macquarie Dictionary defines `information' as: knowledge communicated or received concerning some fact or circumstance; (in communicating theory): a quantitative measure of the contents of a message. For mining companies investing in data capture and information processing technology for operations management is a key issue. Beyond producing performance related information that employees can relate to it is being able to deliver that information into the workplace when it is required, to the employees that can utilise it. To be effective the data needs to be received and understood as `information'. The technology is now available and proven to enable `information' to be delivered into the mining workplace adding value to the activities performed by mine employees. The application of computers and information technology in the mining industry has typically been limited to the resource definition and planning stages, accounting and administration and the process plants that treat the ores and minerals. The mining extraction processes that consume expenditure and determine output in a mining operation occur in an environment dominated by unpredictable events and variable conditions. The mining operation has long been regarded as an inexact science conducted in unpredictable circumstances with many independent variables affecting the output and resultant cost of production. Financial accountants keep track of expenditure and management accountants analyse the cost of production usually on a weekly or monthly basis but all this effort can't affect the outcome, that was determined by the real time events and variations of circumstances over a week ago. Such reporting and analysis can result in conclusions being drawn about what improvements can be made and how you might do better next time, but generally the data is not detailed enough, is inaccurate or misrepresents the real issues. The capital investment required for any mining operation is substantial and comparable to other industries such as manufacturing. The performance and utilisation of manufacturing plants is usually closely monitored down to the lowest level of detail. Many modern plants are controlled and optimised using programmable intelligent devices and monitors display real time performance to the operators and prompt them to make informed decisions to maximise production and minimise wastage. Technology suitable for the mining industry is now widely available and has proven to be a reliable and powerful tool for the optimisation of mining operations. This paper focuses on the latest information technology developed by Modular Mining Systems that has been implemented in mining operations worldwide. The benefits reported by the mining companies utilising real time information technology over the past 15 years have generally related to optimisation of truck fleet allocation and material blending. Some mining operations have reported improvements in equipment utilisation of greater than 20 per cent. With the development of real time graphical display screens in the operators cabins the benefits of information delivery can be harnessed to make employees more effective in the workplace.

Jan 1, 1995

By S Wasi, J Tobiczyk, J Roszkowski

Methane and fire hazards have a vital effect on work safety and continuity of mining plant operation. In the 1990s, the SMP hazards monitoring and ventilation control systems, based on continuous measurement of air parameters, were put into operation at nearly 30 Polish mines. These systems provide continuous measurement of methane concentration within the range of zero to 100 per cent with automatic switching off of electrical energy immediately after detection of potentially explosive conditions. Early detection of coal spontaneous combustion and open fires is made by continuous measurements of CO, CO2, smoke and O2 content in mine air as well as temperature changes in air and rock mass. The essence of the system is intrinsic safety of all underground instrumentation and uninterrupted central power supply from the surface. All abnormal and critical states are signalled to the mine control room. These trigger alarm and emergency procedures. The computer based ventilation monitoring and control system also performs the function of an expert system for fire detection and underground fire fighting. The mine control operator (dispatcher) makes use of stored data in computer escape route schemes and procedures for the safe withdrawal of miners from hazardous areas. The operator can put in motion intrinsically safe alarm signalling units and banners with programmed messages indicating escape routes.

Jan 1, 2005

By Blain CF

For all mineral resource-based companies, it is important to reach the right balance of investment between acquisition and exploration to allow the best chance of achieving long-term corporate goals. The Broken Hill Proprietary Company Limited (BHP) provides an excellent example of success from generative exploration and supports the belief that exploration can be justified, not only in terms of investment criteria, but also because it is essential to a company wishing to build a dynamic profitable growth path based on world-class deposits as cheaply as possible. BHP was incorporated in 1885 to mine a lead/zinc/silver discovery at Broken Hill. The Company has since gone through a steel development phase (1911-1965) and is now in a major phase of growth partly based on exploration success. This third phase was marked by decisions taken in the 1950's to search actively for mineral and energy resources above and beyond the requirements of the steel industry. The commercial successes of this period have been Bass Strait oil and gas, Groote Eylandt manganese, Deepdale iron ore, Gregory coal and Carnilya East nickel. In total at least 22 new resource discoveries have been made in the last 25 years, of which 11 have been developed and several are undergoing feasibility studies. A financial analysis shows that the real value of the returns seeded by discovery covers the real exploration cost many times over. Moreover, the major discoveries have had a spectacular impact on the growth and development of the Company. BHP's present exploration effort is directed towards geological targets which most frequently meet attractive financial criteria and also promote diversification from steel-related earnings.

Jan 1, 1986

By D Smith

The Broken Hill deposit is located in Australia in the far western region of New South Wales. The deposit was found in 1883 and has been mined continuously since its discovery. It is considered the largest lead, zinc, silver deposit that has been discovered in the world and originally contained around 340 Mt of ore at a grade of around 12 per cent lead, ten per cent zinc and 150 g/t silver. The material remaining in the deposit represents only a fraction (perhaps ten per cent) of the original resource. Several of the world’s largest mining companies can trace their origins to the Broken Hill Field. The remaining resources on the CML7 consist of two large lower grade resource lodes that have not been subject to mining, some scattered areas of zinc lode material and the pillars and remnants of the main lead lodes.The deposit occurs in metamorphic rocks of the Broken Hill Group a division of the Willyama Super Group contained within the Curnamona Craton. The Broken Hill Group rocks have undergone multiple phases of deformation. Metamorphism is granulite grade with major shears cutting through the deposit having been retrogressed to mica schists. The deposit lies in an antiform associated with the second phase of deformation.The resultant proposed mine is situated on Consolidated Mining Lease 7 (CML 7) which occupies a strike length of 3.6 km in the central part of the 7.8 km long footprint of the orebody. Underground mining on CML7 ceased in 1975 with surface mining of silver chlorides in the weathered zone continuing until 1991. CBH Resources has been continually working to define and evaluate the remaining resource since 2002. This work has included four surface drilling programs, two underground drilling programs, an exploration decline, enormous amounts of compilation of historical data and detailed three- dimensional (3D) modelling of historical mining and the resource lodes. It is currently planned to commence production at the Rasp Mine in late 2011. The operations will produce from previously unmined lodes and from remnants and pillars.This paper primarily aims to encapsulate the processes involved from information acquisition through to resource estimation and also to highlight some of the challenges encountered and the specific techniques and practices used to overcome them. Many of the experiences at Broken Hill are applicable to all brown field sites.

Aug 22, 2011

By Heidecks C

Sub-level stoping with consolidated rockfill is the main method for mining steep dipping baryte and fluorite veins in Germany. Drifting is fully mechanised using drill jumbos, LHD units and shotcrete support. Stopes have heights up to 50 m with sub-level distances up to 15 m. Winning of the pillars between sub-levels is done by longhole blasting in slices of 3-5 m length on strike. Mucking is done on the lowermost level by LHD units. After each blast rockfill with binder (cement and/or fly ash) is dumped into the scope from the uppermost level. Economic success depends on both geological and technical parameters and factors, eg vein thickness and dip, ore grade, size and distance of sub-level drifts. Of particular influence are ore loss in pillar winning and dilution both in drifting on vein and in pillar mining. A comprehensive computer program has been developed for calculating the total cost per tonne run-of-mine ore respectively per tonne of concentrate for a single stope. The cost model includes development, longhole blasting, mucking and haulage to the mill, milling and ventilation. All costs (labour, energy, supplies, maintenance, depreciation and capital cost) are taken into account. Dilution and recovery are both considered. The program can be used to estimate the cost of mining a particular stope. It can also be used to investigate the influence of relevant parameters and factors on the economic result. By this way it should be possible to optimise the technical design of a stope.

Jan 1, 1995

By K Karmawan, T Casten

The PT Freeport Indonesiaæs Deep Ore Zone (DOZ) copper deposit is located in the province of Irian-Jaya, Indonesia. Currently, a block cave mine is being developed around this deposit. Production is scheduled to start the fourth-quarter of year 2000 and to ramp up to 25 000 tpd by year 2003. The air quantity requirement for this mine is equal to 780 m3/s. To supply this quantity, the mine will require five centrifugal fans (one 450 and four 750 kW fans). This study summarises the technical aspects related to the installation and commissioning of two of these fans. The fans were installed on the surface in parallel arrangement with two others. Each has a design capacity of 240 m3/s of air at 2.2 kPa of static pressure. The study presents the installation details from the underground shaft excavation and portal development through fan testing and commissioning. It also presents the results of a monitoring system that was installed to determine the fan duties.

Jan 1, 2000

By Fullagar P. K

In resource definition and mine development, major capital expenditures are committed on the basis of sparse information and even in production surprises such as bad ground are not uncommon. Drill holes constitute the principal source of information about the orebody and its environment and optimisation of drilling implies maximising the yield of useful information per dollar expended. Geophysical borehole logging provides new flexibility for optimising the drilling budget. Economic benefits can flow from geophysical logging at all stages of the mining cycle. The most commonly cited benefit is substitution of diamond delineation drilling with cheaper percussion or reverse circulation drilling in cases where geophysical logs can substitute for core. This approach can deliver an attractive direct saving in drilling costs (and time) if drill meterage is unchanged, or a potentially greater indirect benefit from better ore control if more holes are drilled within the original drilling budget. More ore contact intercepts per dollar can translate into lower dilution and enhanced ore recovery, thereby increasing revenue as well as reducing mining costs. Substitution of diamond drilling with percussion drilling is not always feasible. However, geophysical logging of diamond holes is often highly advantageous in its own right, both for geotechnical characterisation as well as ore delineation. Operational advantages of logging include data objectivity, speed of interpretation and reduced core handling and analysis costs. Geophysical logging assists mining engineers by providing a continuous measure of in situ rock strength, even over intervals with poor core recovery. The additional expense of geophysical logging in blast holes can be justified in terms of more accurate ore boundary delineation and rock strength evaluation. Precise ore boundary delineation permits refinement of charge placement, to minimise dilution and maximise recovery. Detailed knowledge of rock strength can enable optimisation of blast design. Rock strength can be evaluated in real-time via analysis of drill performance data recorded with measurement-while-drilling (MWD) technology. To successfully apply geophysical logging in mines, its technical, operational and economic viability must all be established. This entails verification of the existence of appropriate physical property contrasts, investigation of the best way to integrate the geophysical results with the mining method and an objective assessment of the value of the resulting mine performance benefit. Geophysical logging is already well established in many mining operations. The greatest impediments to its wider utilisation at mines are: lack of appreciation of geophysics by most mine geologists, engineers and managers; limited interpretational aids; and the necessity to re-enter completed drill holes. In this paper we endeavour to address these issues by informing mine geologists about potential applications of geophysics, by illustrating automated interpretation of geophysical logs and by highlighting the importance of emerging MWD and logging- while-drilling (LWD) technology.

Jan 1, 1997