Search Documents

The optimal production of the metals needed by society is best achieved by a close synergy between concentrate production and smelting. For over 75 years commencing in 1923, such a close relationship was enjoyed between the Sullivan Mine in Kimberley, British Columbia and the Trail zinc-lead complex. An effective program of continual change and improvement at the Sullivan concentrator was achieved through a strong entrepreneurial spirit. This spirit was in part maintained through a favourable location in south-eastern British Columbia that resulted in a dynamic local community that has survived the closure of the mine. Innovations to be reviewed include feed forward reagent control, the use of column flotation to zinc and lead cleaning and the application of ultrafine grinding coupled with concentrate dewatering using hyperbaric filter technology.

Jan 1, 2005

By A Halim

The European Union (EU) have recently issued new Threshold Limit Value-Time Weighted Average (TLV-TWA) for diesel exhaust contaminants, which are CO, NO2 and DPM. The new limits for CO and NO2 were issued in 2017 whilst the one for DPM was issued in 2019. However, in order to allow EU mines to formulate strategies to comply with these new limits, the EU granted a transition period in which mines could use the old limits until the new limits are enforced. The new limit for CO and NO2 will be enforced from 21 August 2023 whilst the one for DPM will be enforced from 21 February 2026. The new limit for NO2 and DPM is very low, 0.5 ppm for NO2 and 0.05 mg/m3 of Elemental Carbon (EC) for DPM. Combination of these two limits would be the lowest among all mining jurisdictions worldwide. It poses a huge compliance challenge to EU mines if they keep using diesel machines. Therefore, a study and a field trial were carried out by the author in 2019–2021 to investigate whether replacing diesel machines with Battery Electric Vehicles (BEVs) would be the best answer to this challenge. This paper outlines results of this study and field trial.

Oct 12, 2022

By Burford B. D, Johnson N. W, Rohner P

Under design philosophy, the Hilton concentrator produced lead, zinc and LGM (lead plus zinc) concentrates. The LGM (Iow grade middling) concentrate was produced by combining coarse middling streams from the lead and zinc circuits, regrinding and subsequent flotation. Mineralogical examination of the zinc circuit middling stream prior to regrinding suggested that production of zinc concentrate from the zinc circuit middling stream should be possible by rearranging existing plant equipment. Laboratory testing of samples of plant products, however, showed that regrinding combined wi th the usual reagent suite was nO1 sufficient to produce a zinc concentrate of the required specifications.Examination of the process water highlighted a problem with dissolved salts in the circuit water, which was solved by in-circuit precipitation of the dissolved ions with soda ash. Implementation of the procedure in the concentrator effectively transferred to the zinc concentrate all sphalerite previously recovered to the LGM concentrate.

Jan 1, 1994

By R Robinson

Modem occupational health practice can be described as the fitting of work to the individual and each individual to his job; perhaps a non-traditional way to view occupational health. This two-component description is achieved through the development of programs to implement and monitor specific job procedures, from the monitoring of unwanted exposures to contaminants to the auditing of mine sites. This paper is about such programs. Some attempt must be made to evaluate the effectiveness of the program and several performance indicators which are intended to measure the effectiveness of such a program are offered.

Jan 1, 1994

The weathering profile, in arid terrains, is commonly capped by different kinds of hardened crust, whose formation is related to recent or former climates. One may distinguish silcretes, calcretes and the ferruginous (or ferro-aluminous) laterites. the present keynote address mostly deals with the lateritic regolith and, moreover, the influence it has on mineral exploration. The lateritic regolith, also called "cuirasse", is a result of a massive accumulation of Fe (and/or Al) oxides on top of weathering profiles developed during former, probably seasonal humid, climatic episodes, and whose preservation depends on the characteristics of later climates. The total thickness of such weathering profiles commonly exceeds 50 m, with an almost complete substitution of the rock forming minerals by secondary minerals as kaolinite and Fe-Al oxi- hydroxides (hematite, goethite, boehmite, gibbsite). Such an alteration of the primary minerals assemblage is of course accompanied by significant changes of the chemical composition, as concerns major and trace elements. The latter are distributed amongst the main secondary mineral phases or trapped in some primary resistant minerals, but may also be leached, totally or partially. Gold is also affected by lateritic weathering, as shown for instance by morphoscopic and geochemical studies of gold grains collected in the different horizons of the profile, which indicates some dissolution followed by reprecipitation.

Jan 1, 1988

By R Wei, Y Peng

With the depletion of high-quality ores, the efficiency of extracting difficult gold ores through flotation and leaching becomes very important in the mining industry. Iron contaminants, sulfide and carbonaceous coatings on the surface of gold and gold bearing minerals significantly hinder the recovery of gold during gold processing. As the surface of gold minerals is easily contaminated, coatings of iron oxides and iron hydroxides originated from the grinding process and oxidation of iron sulfides will cause a retarding effect on both gold flotation and leaching.To mitigate the processing issues caused by undesirable surface coatings on gold minerals, a new technology in treating surface coatings of iron contaminants has been developed. The pulp potential and pH of the slurry are altered to allow dissolution of surface coatings which are further excluded by the use of complexing reagents. The current work shows that iron contaminants can be removed from the surfaces of gold through Eh-pH adjustment and chelation which result in significantly improved gold flotation response. The addition of complexants aids the formation of iron chelates to prevent the iron species in the solution from forming iron oxide and iron hydroxide in the flotation conditions.CITATION:Wei, R and Peng, Y, 2014. Mitigating the effect of surface coatings on gold processing, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 187–192 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By M Paakkunainen

Sampling is often the most critical part in process analysis. When the mean of a continuous lot, such as a process stream within a given time interval, is estimated by calculating the mean of several samples, the uncertainty of the estimated mean depends usually on the sampling strategy. Three different strategies can be used: systematic, stratified or random sample selection. The standard deviation of the lot mean is different for these methods so that systematic sampling usually gives the smallest and random sampling the largest standard deviation. Pierre Gy developed a method where the sampling errors of one-dimensional lots for these three strategies can be estimated from a variogram, which is calculated from a variographic experiment, ie from a set of one-dimensional time series measurements with fixed sampling interval. While variogram is an excellent tool for characterising and displaying the variability of autocorrelated processes as function of time, the sampling error estimation from it is quite laborious, however. In this work an alternative method for estimating the sampling errors was developed. The process is divided into strata of equal sizes, varying the length of strata similarly to variographic analysis. For stratified sampling the standard deviation estimates are obtained by analysis of variance and for systematic sampling by fitting a linear regression line to each stratum and calculating the residual variances. By pooling the individual variance estimates the variance estimates that are corrected for autocorrelation are obtained. The new method was tested with simulated and real data sets having periodic, random and/or drift fluctuations. For stationary processes the results agreed well with the results of the GyÆs variographic method. The method can probably be generalised to estimate the sampling variance of higher-dimensional lots.

Jan 1, 2005

By Pinter R

Several major routes connecting Northern and Southern Europe or Asia run through Austria. These highways have to surmount the alpine range which traverses Austria from west to east. In order to ensure safe driving conditions even in winter, tunnels, at times quite long ones, are necessary. Austria now has tunnels totalling 160 km in length. These tunnels are either already in use or just about completed. The Plabutsch tunnel near Graz will be one of the longest tunnels in the world: approximately 10 kilometers in length. It will be put into operation in the summer of 1987. Before construction could begin, soil and rock conditions had to be investigated by means of a test tunnel. Afterwards, excavation was begun to the full 100 m' cross section. The new Austrian tunnelling method with conventional blasting was used for the major part of the tunnel. It was necessary to have such a large tunnel cross section because a fully transverse ventilation system is installed for environmental reasons. In order to avoid air pollution from the tunnel, exhaust fumes are not allowed to escape from the tunnel portals but from two shafts, each with a diameter of 8.5 m. In this way, exhaust fumes must rise 90 meters or 240 meters before they reach the open air and will thus not affect the city. The ventilation system influences the size of the excavation, and especially the size of the ventilation caverns and the air shafts. All these factors directly influence construction and maintenance costs, and an economical optimisation leads to the appropriate dimensions for the excavation.

Jan 1, 1987

By P Williams

The Sunrise deposit is one of AustraliaÆs largest and most profitable gold deposits. It has consistently and spectacularly outperformed every resource model created. Currently over the life of the Sunrise pit there has been a 50 per cent under estimation of ounces mined. Without a solid basis for predicting the tonnes and grade or the spatial location of mineralisation, mine planning becomes problematic. Recently, through a better understanding of the mineralising processes the reconciliation of the resource model has improved to be in the order of ten per cent under on ounces mined. This paper will describe how the mine geologists at Placer Granny Smith have implemented the changes required to improve the resource model. Work began with the development of a three-dimensional lithological and structural model based on historical drilling and pit mapping. Continual updating of the geological model with grade control logging, assays and in pit face mapping, now allows for the on-going improvement of the resource model and the planning of mine development drilling.

Jan 1, 2000

By C Tapia Cortez, A G. Dempster, R Fradet, S Saydam, T de Roche, R Shishko, J Coulton

Human ventures into space are entering a new phase in which missions formerly driven by government agencies are now being replaced by those led by commercial enterprises – in launch, satellite deployment, resupply of the International Space Station and space tourism. In the not-too-distant future, commercial opportunities will also include the mining of asteroids, comets, the Moon and Mars. This research examines the role of off-Earth mining in a growing space economy. In this investigation, the term ‘mining’ is taken to embrace minerals, ice/water and other in situ resources. As the off-Earth mining initiative could be the engine that drives the space economy, it would be useful to understand what off-Earth mining market conditions and technology requirements are needed for that economy to prosper. These specific elements are studied in the wider context of creating an economy that could ultimately support a sustainable Mars colony. The methodology for developing the model focuses on the extraction of ice from the surface of Mars to produce propellant and water for life support for a possible colony.CITATION:Saydam, S, Shishko, R, Tapia Cortez, C, de Roche, T, Fradet, R, Coulton, J and Dempster, A G, 2015. An integrated economics model for in situ resource utilisation in support of a Mars colony, in Proceedings Third International Future Mining Conference, pp 305–312 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By C Sellens, L D. Fabbro, S Vink

The Fitzroy River Aqua-Eco Health Project is a collaborative research project between the Central Queensland University, the University of Queensland and BMA. It is designed to assess the aquatic ecology and health of the streams within the Fitzroy catchment located adjacent to mine sites. The universities are conducting an independent sampling program expected to yield the most comprehensive monitoring to date. The project design incorporates in situ testing of water quality variables including temperature, dissolved oxygen, conductivity, oxidation reduction potential, pH and turbidity. Water and sediment chemistry incorporate testing for sulfate, suspended solids, nutrients and metals. This sampling is complemented by quantifying changes in the abundance and diversity of a wide range of biota, including microbial, macro invertebrates and fish.This paper will detail the program and highlight some of the particular difficulties in conducting this type of research in ephemeral stream systems. Case study examples will be used to illustrate insights being gained from the program. CITATION:Fabbro, L D, Vink, S and Sellens, C, 2013. The Fitzroy Aqua-Eco Health Project, in Proceedings Water in Mining 2013, pp 117-120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By J Zhou, D M. Hunter, S M. Iveson, K P. Galvin

The recovery and concentration of ultra-fine iron ore can provide significant economic benefits. Presently, there are limited options available given the low settling rates achieved by conventional gravity separation and the relatively poor performance of reverse flotation. The Reflux Classifier is a new water-based gravity separation technology that consists of a set of parallel inclined channels positioned above a vertical fluidised section. This arrangement promotes a powerful throughput advantage compared to conventional fluidisation and a highly selective hydrodynamic basis for achieving sharp separations. A high shear rate develops within the inclined channels, which generates sufficient hydrodynamic lift to convey the lower-density particles (even if they are relatively coarse) to overflow while retaining the high-density particles (even those that are ultra-fine) for discharge to the underflow. The technology has previously been used around the world on particle sizes in excess of 0.1 mm. The present work, however, is concerned with density-based separations down to much finer particle sizes approaching 0.01 mm.A major advantage of the Reflux Classifier technology is the achievement of simultaneous gravity separation and desliming via a single-stage separation. A series of continuous experiments was conducted using an iron ore feed with head grade of 35 wt per cent FeT and nominal top size of 0.106 mm, with 59 wt per cent being below 0.038 mm in size. At a low throughput of 1.5 t/(m2 h), the Reflux Classifier produced high-grade products at a high recovery. For the entire feed, grades of 66.1 wt per cent FeT with Fe recoveries of 80 per cent were achieved in a single-stage separation. Within the 0.020–0.038 mm size fraction, grades of 68.8 per cent were achieved with iron recoveries of 94.7 per cent. Excellent recoveries of up to 57.0 per cent were achieved for the -0.020 mm size fraction. The ability of the inclined channels to retain the fine dense material further enhances the effectiveness of the Reflux Classifier by creating an autogenous dense medium effect within the vertical section. This helps to elevate large gangue particles up into the overflow.CITATION:Hunter, D M, Zhou, J, Iveson, S M and Galvin, K P, 2015. Gravity separation of ultra-fine iron ore in the reflux classifier, in Proceedings Iron Ore 2015, pp 143–148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By N Madani, S Abulkhair, N Morales

Conventional geostatistical algorithms cannot reproduce bivariate complexities such as inequality constraint, nonlinearity and heteroscedasticity. Poor reproduction of these features may decrease the accuracy and reliability of mine planning results. For example, it is not unusual to have an inequality constraint between primary and disturbing elements in a metalliferous deposit. Implementation of traditional methodologies for such complex data sets can lead to the incorrect reproduction of a bivariate relationship, which will affect the validity of NPV results. In this paper, an iron data set containing iron and silica grades with an inequality constraint between variables is introduced as a case study. This study proposes an algorithm based on a hierarchical sequential Gaussian cosimulation integrated with inverse transform sampling. The proposed methodology considers the linear inequation between two variables in the hierarchical cosimulation process to reproduce an inequality constraint. As a comparison, conventional sequential Gaussian cosimulation is also applied to the same data set to demonstrate the difference in bivariate relationships from both models. Unlike the proposed algorithm, the conventional cosimulation cannot reproduce an inequality constraint and slightly overestimates silica grades. The modelled realisations are then used to assess the uncertainty of a plan and generate a stochastic strategy that adapts the destination of the blocks depending on the scenario. Two-stage stochastic long-term production scheduling takes extraction decisions using average information (ie e-type model) and ore/waste destinations based on geostatistical realisations. As a result, the proposed strategy is closer to the upper bound, highest possible NPV for each realisation, than to the lower bound, deterministic strategy that does not manage the risk of sending extracted material to wrong destinations. Furthermore, Comparing production schedules resulting from proposed and conventional geostatistical methodologies shows the importance of inequality constraint reproduction and more accurate long-term mine planning.

Nov 8, 2021

By S Jahn, M Noel, E M. Rykaart, M Pau

Three soil cover test areas were constructed on waste rock backfilled into the Lichtenberg Pit, near Ronneburg Germany. A fourth, uncovered area was included as a control. Each test area measures 50 m by 65 m, and was constructed using full-scale equipment and construction practices. Extensive material sampling and testing was included as part of the construction. Devices were installed in each plot to monitor meteorology, infiltration, run-off, interflow, soil moisture, soil temperature, and soil pore gases. Boreholes were completed in each area and instrumented for temperature, pressure and pore gas sampling to a depth of approximately 60 m. Data from the monitoring instruments have been collected since July 2000, and have been comprehensively analysed and modelled on two occasions. The paper presents an overview of the test area design and instrumentation and the results of the two comprehensive data reviews. The reliability of the various monitoring methods is discussed and experience with several innovative methods is reviewed. The difficulties encountered in modelling the data set using common soil physical models are discussed.

Jan 1, 2003

By Coates D. F, Neil T. J, O&apos

A proper economic analysis of pit slope design must reflect the trade-off between the benefits and the increased risks of slope fail- ure inherent in steeper slope angles. However, no formal framework for a proper analysis existed to date. This paper describes the results of the past four years' effort in which a formal eco- nomic analysis framework was developed and tested through a case study. This framework, in essence, consists of the availability of tested procedures and com- puter programs. The procedures as well as the programs are divided into two broad functional categories; (1) the first category related to assessing the economic benefits and costs associated with various pit slope angles and (2) the second category that determines the overall financial impact which the assessed benefits and costs exert to the mine operator's overall economic stature.

Jan 1, 1977

This paper concerns a pragmatic approach to a problem that is common to many operations in the mining industry: how, over the short-term, to grasp the extent and distribution of long-term financial risk from environmental causes and reduce these risks strategically, in order to maintain stability and flexibility in the operations. Surprisingly, many companies operate without an environmental master plan or tools that can help managers measure and reduce financial risks. Such companies may be subject to unknown unacceptable financial risks from environmental causes. While many companies have some kind of internal system of environmental standards, it is often the case that such systems have uneven or limited effect, and offer no opportunities for visualising, measuring or managing aggregate financial risks from environmental causes. `Aggregate risks' are defined here as the calculated total expected financial costs to a company, or a subdivision of a company, from environmental causes at nominated operations over a defined time period. Aggregate risks take into account the type and magnitude of an environmental problem set, the likelihood of occurrence, and the time frame during which the problems will develop or solutions are required. For the large corporation, the 'amount of' aggregate environmental risk is a statistic that can be managed, along with other financial parameters, at the corporate level to improve the stability and predictability of operations, and protect the interests of shareholders. This paper concerns development of a management framework and a tool for the large corporation that responds to the need for managing aggregate environmental financial risks. The logical framework proposed to overcome the need for strategic vision is the Environmental Master Plan, and this is described in the next section. The analytical tool proposed to measure aggregate risks and provide relevant data and insights to managers, is called an Environmental Risk Management Information System, and its mechanics are described in a subsequent section.

Jan 1, 1994

By G D RICHMOND, Campbell J. J

Aberfoyle Limited has developed the Hellyer complex base metal sulphide deposit located in North West Tasmania. As part of exploration and feasibility study, the ore was extensively tested, including trial milling, and was found to be very fine grained and to have poor flotation selectivity. Substantial innovation was required to produce saleable concentrates at acceptable recoveries and costs. Efforts were made to reduce operating costs, to improve metallurgical performance and to improve work organisation. These efforts were pursued both in design and in subsequent plant operation. This work has resulted in a very competitive operation with production costs in the lowest quartile of the industry. Examples of the measures taken are presented and the results are evidenced by improved plant performance since commissioning.

Jan 1, 1992

By L B. Sukla, V N. Misra

Microbial desulfurisation of coal has significant advantages over physicochemical desulfurisation processes since the former process selectively removes the inorganic sulfur compounds and heavy metals without significant carbon loss. The purpose of this study was to improve the desulfurisation yield of a coal sample from northeastern coalfields, Assam, India using microbial technique. The coal sample contained 2.13 per cent of total sulfur and 2.59 per cent of ash. Stirred tank reactors of 40 L capacity were operated in batch mode. Initially, the reactor was fed with 40 L of slurry containing ten per cent (w/v) coal, ten per cent (v/v) inoculum of mixed culture of mesophilic acidophiles, native to coal itself and the requisite amounts of constituents for 9K medium without added ferrous sulfate. The percolate of the reactor was then used to seed the medium for the next experiment. The purpose was to obtain a better adapted and more active biomass which would give a better desulfurisation yield for coal. Further studies were conducted in the bioreactor, fed with 40 L of slurry containing ten per cent (w/v) pulp density of coal, ten per cent inoculum (derived from previous studies) and the medium, supplemented with ferrous sulfate. Results showed an increased total desulfurisation yield of 43 per cent in the latter treatment in comparison to the previous one, where the desulfurisation yield was only 23 per cent. The findings also demonstrated the convenience of using inocula derived from coal, where 50 - 60 per cent of pyritic sulfur was removed, while chemical desulfurisation is of little significance with the majority of coal types. The ash content was also reduced to 1.74 per cent as the low pH of the process caused dissolution of a number of common minerals present in the coal.

Jan 1, 2004

By McAllister J

Oxygen was in restricted use at Port Kembla until tonnage oxygen became available for steelmaking in the open hearth furnaces. In adopting the new process various modifications to furnace design and operation were necessary and some of these, including increase in roof height and variation in firing and draft control, are discussed.The design of oxygen lances is also discussed and various steelmakingtechniques considered.Steel production increased with oxygen roof lancing-one- furnace producing 8,507 tons in one week-but new problems, such as rate of refractory wear, and disposal of fumes, were created.Design of future open hearth oxygen furnaces is predicted.INTRODUCTIONIn the post-war era, the availability of "tonnage" oxygen caused a major revolution in steelmaking techniques. Various pneumatic processes showed that steel can be madeat a very fast rate and that oxygen steelmaking can be applied to open hearth furnaces. Methods used are surface impingement with roof lances, bath injection with door lances, flame enrichment with fuel firing, mixed gas and oxygen firing, and enrichment of normal combustion air by oxygen injection into the flue systems.Owing to its previous restricted availability and high cost, oxygen was used in rather small quantities in the open hearth furnaces at Australian Iron and Steel Pty. Ltd.(A.I. & S.), Port Kembla, until about the middle of 1960.At that time tonnage oxygen became available and roof lancing commenced on No. 33 furnace at No. 2' open hearth shop.

Jan 1, 1962

At the outset I want to thank you for inviting a representative of the Chamber of Mines of South Africa to address you on the subject of mining and its future at this, the 13th Congress of the Council of Mining and Metallurgical Institutions. It is indeed a pleasure and an honour to be here. As many of you will recall, four years ago I, as the then President of the South African Institute of Mining and Metallurgy, had the privilege of hosting and welcoming you to the 12th Congress, the third such congress hosted by South Africa. The late Sir Ernest Oppenheimer, President of the 1930 Congress - the first to be held in South Africa - in his opening address foresaw the mining industry as "the most potent factor in spreading the benefits of civilisation over the sub-continent." We have come a long way since those halcyon days but, as I noted four years ago, it still remains true that mines have been, and will continue to be, the missionaries of development in many, if not most, of the Third World countries. I have been asked to address you on the subject of "mining" and to let my imagination roam widely so that delegates can leave the congress with a broader vision than they brought on arrival. It is a tall order and in my attempt to fulfil it I ask you to cast your minds back 120 years to a sultry, rustic day when the first diamond was discovered in South Africa at the now famous town of Kimberley. At that time the South African economy, predominantly pastoral, was still at subsistence level. Almost overnight the ensuing diamond rush turned the then British- owned northern Cape Colony's semi-desert scene into a hive of mining activity, every prospector bent on making his instant fortune. It was very little different, I am sure, to the gold rushes that hit California in 18+8, Australia in 1851, New Zealand in the 1860s. and the Yukon in the 1890s.

Jan 1, 1986