Search Documents

By J. J. Jakosky

The fundamental hydrodynamic principles governing the production of oil from wells have been carefully studied and evaluated by many investigators. These prior studies are quite complete and cover virtually the entire field of oil production and recovery.' One of the most important measurements in production studies is that of the bottom-hole pressure at various rates of production.2 It is the purpose of this paper to outline the technique and economics of fluid-level measurements as applied to pumping wells and to review briefly other methods for obtaining bottom-hole data. The applications of bottom-hole pressure or fluid-level measurements are based on simple hydrodynamic principles. Under equilibrium conditions, pbh = hd + pg + pch [1] when pbk = bottom-hole pressure, Ib. per sq. in. absolute, h = height of fluid in well, ft., d = average fluid density, Ib. per sq. in. per foot, p, = weight of section of gas column 1 in, square from fluid level to casinghead, Pch = casinghead pressure, Ib. per sq. in. absolute. In words, equation 1 states that the bottom-hole pressure is equal to the weight hd of the column of fluid plus the weight of the column of gas between the fluid and the casinghead plus the casinghead pressure. At moderate rates of flow, the rate of production is approximatcly proportional to the difference between the reservoir, or static bottom-hole. pressure and the flowing or producing pressure; i.e.: Q = c(pr - pbh) [2] pr = the reservoir pressure, c = the constant of proportionality. However, at production rates approaching zero and also at high rates the proportionality may break down. By combining equations 1 and 2 the

Jan 1, 1939

By J. J. Jakosky

The fundamental hydrodynamic principles governing the production of oil from wells have been carefully studied and evaluated by many investigators. These prior studies are quite complete and cover virtually the entire field of oil production and recovery.' One of the most important measurements in production studies is that of the bottom-hole pressure at various rates of production.2 It is the purpose of this paper to outline the technique and economics of fluid-level measurements as applied to pumping wells and to review briefly other methods for obtaining bottom-hole data. The applications of bottom-hole pressure or fluid-level measurements are based on simple hydrodynamic principles. Under equilibrium conditions, pbh = hd + pg + pch [1] when pbk = bottom-hole pressure, Ib. per sq. in. absolute, h = height of fluid in well, ft., d = average fluid density, Ib. per sq. in. per foot, p, = weight of section of gas column 1 in, square from fluid level to casinghead, Pch = casinghead pressure, Ib. per sq. in. absolute. In words, equation 1 states that the bottom-hole pressure is equal to the weight hd of the column of fluid plus the weight of the column of gas between the fluid and the casinghead plus the casinghead pressure. At moderate rates of flow, the rate of production is approximatcly proportional to the difference between the reservoir, or static bottom-hole. pressure and the flowing or producing pressure; i.e.: Q = c(pr - pbh) [2] pr = the reservoir pressure, c = the constant of proportionality. However, at production rates approaching zero and also at high rates the proportionality may break down. By combining equations 1 and 2 the

Jan 1, 1939

By R. M. (Mike) Robb

Introduction The requirements to investigate a wide range of alternatives and analyze a variety of ‘what if’ questions make the automation of pit design a requirement in today’s rapidly changing mining industry. The wide-spread application of computers has relieved the engineer of much of the tedious and error-prone work related to mine design. He is thus free to do the creative and innovative thinking for which he is trained. It is now possible to investigate a large number of alternative pit designs in a reasonably short time period. In the past it was very easy for a team of engineers to consume 12 to 14 man-months in the detailed hand design of a large open pit. The pressure of today's mining industry, the desire to investigate a variety of alternative designs, and the shortage of qualified engineers make the slowness of hand design less preferred.

Jan 1, 1979

By G. F. Tagg

Earth-resistivity measurements are often of service in obtaining information regarding geological formations, particularly when applied to structural problems. In such problems the masses of the various bodies are large, and have a corresponding effect on the average resistivity of the soil. Much work has been done using such measurements, but in general the method of interpretation employed is empirical. Since certain simple cases can be investigated mathematically, it appears to be quite sound to endeavor to apply the mathematical solutions to the practical results, in order to deduce from the latter such unknown quantities as depth. This paper deals with such a method of interpretation for the simple case of a single horizontal stratum. In the method described by Wennerl for measuring earth resistivity, four stake electrodes are driven into the earth in a straight line as shown in Fig. 1. A current I amperes is passed between the two outer stakes and the potential difference V volts between the two inner stakes is measured. Then if a is the electrode separation, the specific resistance of the soil, which is assumed to be homogeneous, is given by the formula P = 2?v/1 [1] v or if v/1 is called a resistance R ohms, p = 2?aR [2] If a is in inches, p will be in ohms per inch cube, or ohm-inches, and if a is in centimeters, p will be in ohms per centimeter cube or ohm-centimeters. As stated above, this formula is true only if the earth is homogeneous, and when this is not the case an application of one of these formulas

Jan 1, 1934

By K. R. Carson, J. Weertman

An attempt is made to ascertain the mechanism of tangle and cell formation and its dependence upon dislocation-interstitial carbon interactions. The strain-hardening behavior of single crystals of 3.25 pct Si-Fe was determined at 300° and 425°K and under conditions of both continuous and interrupted tensile strain. Significantly enhanced hardening was observed in crystals deformed at the elevated temperature, and it was further accentuated by interrupted straining. Transmission electron microscopy was used to study the resultant dislocation structures. Strain aging was found to aid tangle and cell formation at 425°K, but at both temperatures embryo tangles formed solely from primary glide dislocations, presumably by a process involving cross slip and "mushrooming". IN the course of plastic deformation all bcc metals and alloys develop a dislocation structure characterized by loose-knit groups of tangled dislocations. With increasing strain the tangles become more tightly knit and grow larger; finally a three-dimensional cellular substructure is formed:1 This process has been observed with the transmission electron microscope.'-l7 However, most investigations were confined to the study of nearly pure polycrystalline metals at relatively low temperatures. At intermediate temperatures, 0.17 to 0.14 Tm where T, is the melting temperature in degrees absolute, the mobility of interstitial impurities such as carbon is high enough to permit migration to nearby glide dislocations but is still low enough so that a significant drag force is exerted.18,19 it is also in this temperature range that a hump occurs in the curve of work-hardening rate vs temperature for iron. Analogous plots for tantalum" and columbiumzo show a definite upward trend in the work-hardening rate. Keh and Weissman1 have pointed out that this behavior may be explained solely on the basis of changes in the dislocation configuration: at low temperatures the dislocations tend to be relatively straight and uniformly distributed, but at intermediate temperatures tightly knit tangles and cellular substructure appear. The interference of these tangles with glide dislocations causes the observed increase in the work-hardening rate. This explanation appears reasonable, yet one might ask what factors cause tangle formation to be so favorable at intermediate temperatures. It seens likely that the strong dislocation-interstitial interactions which are known to occur in this temperature range are at least partly responsible," with the magnitude of the effect being proportional to the interstitial concentration. The purpose of the present work is to study the relationship between tangle formation and strain hardening in a bcc metal in the temperature range 0.17 to 0.4 Tm. Particular emphasis was placed upon a study of the effects of interstitial-dislocation interactions. Single crystals of 3.25 pct Si-Fe containing about 200 ppm of C in solid solution were used in the investigation for the following reasons: 1) The mobility of interstitial carbon in 3.25 pct Si-Fe is negligible at 300°K but increases rapidly at slightly elevated temperature22. Hence, differences between the flow curves and dislocation structures of crystals deformed at 300°K, 0.17 T,, and crystals deformed, say, at 425°K, 0.24 Tm, should be appreciable because of the enhanced dislocation-carbon interactions at the elevated temperature. This effect was accentuated in some samples by interrupted straining, thereby introducing a certain amount of aging. 2) Near room temperature, slip in suitably oriented 3.25 pct Si-Fe single crystals is largely confined to the (110) planes.23'24 Dislocation structures formed under conditions of single glide are the least complicated and their method of formation is the most easily discernable. 3) Dislocations in Si-Fe can be tightly locked with carbon atmospheres by a low-temperature aging treatment. The subsequent thinning of samples to foil thicbess causes little or no rearrangement in the dislocation structure.25 EXPERIMENTAL PROCEDURE Large single-crystal sheets of 3.25 pct Si-Fe were donated by Dr. C. G. Dunn of the General Electric Research Laboratory, Schenectady, N. Y. The orientations of the sheets were determined and slabs 1.0 by 0.25 by 0.05 in. were cut such that the desired tensile axis corresponded to the long dimension. The slabs were mechanically polished and subsequently decar-burized by heating at 1000°C for 3 days in a flowing wet-hydrogen atmosphere. A carbon content of about 200 ppm was introduced by heating at 805°C for 25 min in a flowing atmosphere of dry hydrogen containing heptane vapor. Shaped copper tools were then used to spark-machine at 0.125 by 0.50 in. gage length onto each slab. Vacuum annealing at 1225°C for 2 days followed by a quench into the cold end of the furnace to retain carbon in solid solution concluded the soecimen preparation. Continuous tensile flow curves for crystals of severa1 orientations Were obtained both at 300' and 425°K. A strain rate of 6.67 x 10-4 Per set was used in these and all other tests. Crystals oriented for single glide, B and D in Fig. 1, were subjected to a 3.5 pct plastic elongation to insure uniform slip along the gage length; they were then immediately subjected to interrupted strain cycling as indicated in Fig. 2(a). Each cycle consisted of unloading to 1.5 kg per sq mm, holding

Jan 1, 1969

By Cyril Stanley Smith

ON the 6th of February 1684, Dr. Martin Lister mentioned at a meeting of the Royal Society1 that "brass is magnetical," and promised to give an account of that assertion at some other time. He repeated his promise but never fulfilled it, and it was left for William Arderon2 to show, in 1958, that brass could be made magnetic by hammering and that it would retain polarity after magnetizing. Twenty-seven years later Cavallo3,4 examined the matter in great detail. Working with cast calamine brass, he showed that it could be made magnetic by hammering and nonmagnetic by subsequent annealing at a red heat. He found that annealing at a very high temperature caused the samples to lose their magnetic quality permanently, even after subsequent cold-working, but that remelting and cold-working restored it. He encountered some samples of brass that could not be rendered magnetic by any treatment. Experiments in which these were remelted with iron additions gave negative results, and Cavallo concluded that iron impurity was not the cause of the magnetism. He worked with 50-grain (3-gram) samples melted under the blowpipe, hence cooled very quickly. Bennet5 made whole crucible charges from copper and zinc, and found the resulting brass ingots to be magnetic only when iron had been added and then only after cold-working. All these observations applied to material in the cast condition, in which coring would produce a continuous spectrum of composition and cooling would result in varying degrees of precipitation. This knowledge of the subject seems to have been forgotten in the nineteenth century. The older brass was made by the calamine process and frequently contained iron in amounts of 0.5 per cent or more, absorbed from the impure ore with which the copper and charcoal were heated in making the brass. When metallic zinc became available in commercial quantities, calamine brass gradually disappeared, and with it the knowledge of its curious magnetic properties. Only when sensitive apparatus replaced the compass needle of the earlier investigators could the effects be detected in relatively pure metal. The effect of cold-working in inducing ferromagnetism was rediscovered by Bitters in 1930 in a sample of impure copper, and this was confirmed by Lowance and Constant,9 Honda and Shimizu, 10,11 and others. In the same year, Tammann and Oelsen12 showed that copper-rich copper-iron alloys after certain heat-treatments could be rendered ferromagnetic or made more strongly ferromagnetic by cold-rolling. Kussman and Seeman13 showed that the change of susceptibility of relatively pure copper on cold-working was associated with the iron content, and concluded that actual precipitation of iron was caused by cold-working, which is a satisfactory theory until one considers the improbably high rate of diffusion that this would involve. When studying precipitation phenomena in

Jan 1, 1941

By Parke A. Hodges

CHROMIUM, one of the most vital of the strategic metals, has constantly increasing importance as research expands potential uses in alloy steel metallurgy. All signs point to a steadily growing use for chrome ore, and the general subject has received a great deal of attention recently.1 A relatively little known country, Southern Rhodesia produced a total of 5.949 million tons, or 18.6 pct of the total world chrome output, between 1906 and 1950, according to figures from the U. S. Dept. of Commerce. According to U. S. Bureau of Mines figures, Southern Rhodesia produced 291,525 tons in 1950 and 300,267 tons in 1951, or approximately 13 and 11 pct, respectively, of world production for the two years. In 1953 the Rhodesian Vanadium Corp. produced about 85,000 tons of which probably 7,000 tons were concentrate. Production by other companies was high. Large in themselves, the figures assume even greater significance because most of this output is of metallurgical grade.

Jan 8, 1954

By J. M. Locke

BRÜCKNER's revolving cylinders for roasting ores, etc., are now used at a number of the mills in Colorado and New Mexico, for the purpose of roasting and chloridizing silver ores, with highly satisfactory results, even from those cylinders of small size, erected before the many improvements of recent date. As examples of the larger improved cylinders, reference can be made to those erected at the Tennessee Reduction Works, Silver City, Grant County, New Mexico, and those which were built, in 1871, at the celebrated Caribou Silver Mill and Mines, Colorado, a mining enterprise which has proved so satisfactory as to have been lately sold to a Holland company for an enormous amount. These cylinders, as now constructed by Messrs. Lane & Bodley, of Cincinnati,, Ohio, are shown in Plate III, in which Fig. 1 is an elevation in perspective, Fig. 2 a longitudinal, and Fig. 3 a trans¬verse section. Fig. 4 is a sketch of a mill, with Brückner's cylinder. The exterior of the cylinder is a shell of boiler iron, 12 feet long by 5 feet 6 inches in diameter. The ends are partially closed with similar material, leaving in the centre a circular opening about 2 feet in diameter, bounded by a flange projecting several inches.. Upon one side is placed an opening closed by a hinged door. Upon the outside of the cylinder are bolted three bands, as shown in Fig. 1, in which the section of the first is square, and that of the third semi¬circular; the second, or middle band, is a strong spur gear. Passing through the cylinder are six pipes parallel to one another, in a plane at an angle of 15° to the axis of the cylinder; these pipes also lie in this plane at an angle of from 30° to 35° to the longitudinal, axis of the plane, as shown in Fig. 2, where the internal arrangement of the cylinder is seen, a perforated diaphragm being formed through part of the cylinder by means of perforated plates placed between

Jan 1, 1874

By Gerald Edmunds, R. K. Waring, E. A. Anderson

Brass is liable to failure under the combined influence of stress, certain corrosion media, and time, a phenomenon commonly termed season cracking or stress-corrosion cracking. The consequences of this are serious in applications of brass generally, including the important field of cartridge cases. Cartridge cases (70 Cu: 30 Zn) that fail from this cause may allow the escape of gas from the gun breech, a hazard to the shooter, and may not eject, thus temporarily putting the gun out of action. In loaded cartridge cases, the stress present is partly residual from the, drawing and necking operations and partly applied by the insertion of the projectile. Ammonia, present as a decomposition product of smokeless powder, air and moisture constitute corrosive media. The prevalence of season cracking has been reduced considerably, but not eliminated, during the past quarter of a century by low-temperature annealing to relieve stresses residual from fabrication, a method suggested by Diegel 38 yr. ago(I).2

Jan 1, 1945

By Heinrich Ries

In another place,* the writer has called attention to the modern methods of the laboratory investigation of clay, and it is desired here simply to discuss one branch of the subject, which, though of considerable importance, has heretofore received little attention in this country, viz., the rational analysis of clay. In order, however, the better to point out the bearings and advantages of this procedure, it is necessary to refer briefly to the ultimate analysis as well. The remarks in this paper refer only to the use of clay for the manufacture of clay-products. Pure clay or kaolin-f is extremely refractory, possesses little plasticity, and usually shrinks aud warps considerably in burning. Even the smallest proportion of impurities changes these properties, so that the kaolin exhibits variations in shrinkage, plasticity, tensile strength, fusibility, and often color when burned. The majority of nearly pure kaolins consist of kaolinite (A1,O2 2SiO,, 2H20), undecomposed feldspar, and quartz. The kaolinite generally forms the finest particles of the clay and is known as the clay-substance, while the rest of the clay-particles are collectively spoken of as sand. In the ordinary or ultimate analysis, the substances generally determined are silica, alumina, ferric oxide, lime, magnesia, alkalies and water. An analysis of this type simply regards the clay as a mixture of elements or oxides, but gives no clue as to the actual condition in which these substances exist, i.e., whether as silicates, oxides or carbonates, etc., a point which it is of the highest importance to know; for the individual components of the clay influence its properties not only according

Jan 1, 1899

By Paul J. Sirkegian

The problem of properly controlling the movements of underground trains in the Emma Nevada and Morris Brooks workings of the Consolidated Coppermines Corporation of Kimberly, Nev., became more complex as the rate of production increased. Ore from these mines, which are connected through a 7000-ft. single-track haulageway (Fig. I), is hoisted through the Emma Nevada shalt. All production to date has been from one level. Because of heavy ground, even on the main haulage horizon, experience has shown that it is necessary to have a minimum cross section in the drifts, thus making it impractical to have a double track system. In 1937, production was 3000 tons per day; in 1938 it was increased to 6000 tons per day and in 1940 to 9000 tons per day. Each increase necessitated a revision in the method of controlling the underground traffic. In 1937 the tramming signal system consisted of a few signal lights in the main haulage drift. These lights were two 100-watt bulbs in a metal box that had one green and one red lens on each side. The box was mounted on the underside of a drift cap timber and could be seen For a considerable distance. The lights were so arranged that all boxes showed either red or green at the same time and all were controlled by a magnetic contactor at the entrance to each lateral drift. When the lights showed green, the main haulage was clear of traffic and a train could enter it. As the motor entered the main haulage drift, the motorman pulled the cord of the magnetic contactor switch, thus changing all the main haulage lights to red, which indicated that no other train could use the main haulage until the first train had turned into a lateral drift. When a train left the main line, its motorman pulled the cord connected with the magnetic contactors, causing the haulage lights to show green again. This arrangement permitted only one train at a time to use the main haulage and thus limited the number of train trips per shift, but it was satisfactory when the ore handled was only 3000 tons per day. Second SystEM Installed With a gradual increase in production it became necessary to place a train dispatcher in charge of all trains. He controlled their movements orally, giving his orders direct or by mine phone, instructing them where to load, when to leave for the station and when to return. His objective was to group several trains traveling in the same direction. Because of the human element involved, some mistakes were made. The danger of a serious collision was always possible. There was a 90° turn and curve in the underground haulageway, therefore travel in this section was always dangerous if mistakes were made in directing traffic. To protect the train crew, particularly the rear switchman who rode the last car or caboose, a two-way push button and flash-signal system was installed on the

Jan 1, 1946

By George M. Bouton, Lawrence Ferguson

The experiments described in this publication were inspired by the Bell System's large interest in lead-alloy sheathed cables and by the wide range of fatigue and corroding conditions to which they are sometimes subjected in service. The first experiments consisted of operating specimens of lead + I per cent antimony telephone cable sheath alloy in a fatigue test while they were immersed in water taken from a manhole. Because of many published reports concerning corrosion-fatigue phenomena of various metals and alloys, a reduction in fatigue life was expected(1)2 Instead, however, the fatigue test ran on for many times the normal number of cycles an4 was finally stopped without failure. Because of this, the experiments were broadened to include the effect of many media on the fatigue properties of four lead alloys over a wide range of testing speeds and strains. One material, a viscous tacky polymerized isobutylene3 used in

Jan 1, 1945

By J. C. Van de Water

In June the supply of M3 army demolition powder being used for mudcapping was depleted and we switched to 4 by 8, 60% Special Quarry Gelatin dynamite. This size cartridge has proved convenient, as a half stick will handle the average boulder. By keeping the gelatin in the paper while cutting it in two, there is little contact with the gelatin and therefore fewer headaches among the powdermen. To further help prevent the headache nuisance the men are furnished with plastic coated gloves. Boulder breaking costs as reported last year were $0.426 using M3. This year, 8180 boulders have been broken with M3 at a cost of $0.472 each and 7479 with 60% Quarry Gelatin at a cost of $0.660 each. This rise in cost is due entirely to the greater cost of the Gelatin as the method has not changed.

Jan 4, 1950

By W. C. Lacy

A WIDE variety of metalliferous deposits in Peru shows a close and consistent relationship to intrusive and extrusive igneous rdcks. This relationship furnishes a clue to the comp(osition of ore-bearing fluids and to the timing in separation of these fluids from differentiation magma Conclusions presented here are based on ten years' study of a large number of metalliferous deposits in Peru. The most important of these areas are shown in Fig. 1. The structural relationship of meta1 mineralization to the intrusive series and of the members of the series to each other can be illustrated by three examples: I The well described Cerro de Pasco (Ref. 1, p. 160) sulfide mass shown in Fig. 2 is localized along the ' eastern contact of an agglomerate-filled crater. Quartz-monzonite porphyry and related intrusive breccias, which in places border the pyrite mass On west, are replaced by the pyrite and cut by later transverse vein structures. Late unmineralized but

Jan 1, 1958

By Charles Catlett

Some years ago the writer was struck by what might be called the remarkable vitality of the Virginia furnaces during the panic of 1893; and attention was called to the fact in the American Manufacturer of February 8,1895. From the second half of 1892, which was a period of maximum output, to the second half of 1893, when the full effects of the depression had been reached, the output of pig-iron had fallen off in Illinois 85; in New York, 66; in Ohio, 51; in Tennessee, 44; in Pennsylvania, 28; and in Virginia only 15 per cent. It seemed a reasonable inference that the State which had thus shown its marked ability to meet hard times could make and market its product with a larger margin of profit than any of the other States. This was true at that time, and to a certain extent the reasoning still holds good; but my mistake was in not fully realizing the marked effect of the Mesabi development, combined with reduced economies in transportation, and the consequent advantage to those furnaces which were so situated as to utilize these new commercial factors. The effect of these factors is seen in comparing the second half of 1894 with the second half of 1892. New York had dropped off 44, Alabama 23, Tennessee 21, Illinois 19, and Virginia 16 per cent., while Pennsylvania had increased 5 and Ohio 10 per cent. While there is no question of the great economy which has been made possible for certain interests which are peculiarly situated with reference to the ores of the Northwest, it is yet too early to say what furnaces not so fortunate will have to pay for their raw material. Already an increase of twenty cents per ton of ore has been announced, based upon increased cost of production.

Jan 1, 1900

By J. J. B. Rutherford

IT is now well known that troublesome intercrystalline corrosion may occur in austenitic stainless steels following exposure of the metal to a temperature within the range 1000° to 1500° F. (540° to 815° C.). The present paper describes a satisfactory method of estimating the extent of such corrosion, based on the measurement of the electrical resistance of a specimen before and after attack. This new method enabled us to study quantitatively the effect of several factors upon intergranular corrosion in the 18 Cr, 8 Ni type of alloy. The results show that susceptibility to this attack increases with increasing carbon content and grain size and appears to pass through a maximum for certain combinations of temperature of sensitization and period during which the alloy was maintained at that temperature; and are in complete accord with our interpretation of the mechanism of this phenomenon. The method is probably applicable to other metals or alloys subject to intercrystalline attack, such as the aluminum alloys of the duralumin type. The methods hitherto in use for estimating the degree of intergranular attack fall into three types: (1) microscopic examination,1 (2) macroscopic examination of fractures, and (3) determination of the time required for complete failure or disintegration .2 None of these lends itself very well to a measurement of the extent of corrosion. The first two are qualitative in nature and the third provides an arbitrary value largely dependent on individual judgment, since failure is a progressive phenomenon and not a sudden event. Our experience is that weight-loss determinations, although valuable in some types of corrosion investigations, bear no simple relation to intercrystalline corrosion in this type of alloy, as is to be expected since the phenomenon probably involves only the thinnest films between adjacent metallic grains.

Jan 1, 1932

By C. Y. Garber

INTEREST in the sink-float plant operated by the Bunker Hill and Sullivan Mining and Concentrating Co. at Kellogg, Idaho, has recently been largely confined to the preparation and reconditioning of the galena medium. The ease and simplicity of these operations in a concentrating mill producing a flotation lead concentrate has occasioned enough comment to possibly justify a brief description. The subject is treated from an operator's viewpoint only; no effort is made to discuss it in a theoretical or technical manner. PLANT AT BUNKER HILL The sink-float plant was first operated in December 1941. It was built for the purpose of quickly increasing mill capacity with a minimum of equipment. It is the Huntington-Heberlein sink and float process using galena medium and is operated under license from the Sink and Float Corporation, New York city. Lead-zinc ore from the Bunker Hill mine is crushed to pass a I ¼ in. screen and is then washed and separated on vibrating screens having 4 ½ -mm. round-hole punched plates. The screen undersize, amounting to 33 per cent of the mill feed, is dewatered and sent to the ball-mill feed bins. The screen oversize goes to the sink-float plant, where 50 per cent of the oversize, or 33 per cent of the mill feed, is float, which is washed free of medium and disposed of as a tailing. The remaining 33 per cent is sink, which, after washing, is crushed to pass ½ in. and joins the undersize in the ball-mill feed bins. The normal plant capacity is 1700 tons per 24 hr. About 1.7 per cent of the total lead and 3.3 per cent of the total zinc in the feed is lost with the sink-float tailings (Table I). [ ] More complete descriptions of the H. H. process and Bunker Hill sink-float plant are given in several recent articles, listed at the end of the paper. PREPARATION OF MEDIUM AT BUNKER HILL New medium is made intermittently as needed, usually 12 hr. in each 6 days. A small portion of the current mill flotation concentrate is diverted from the lead cleaner cells to a I-in. vertical sand pump and pumped to a two-cell 36-in. Agitair flotation machine, where NaCn and ZnSO4 are added and the grade of concentrate is improved as shown in Table 2. Tailing from this operation is returned by gravity

Jan 1, 1946

By Byron W. Cheever

In working up the process which I described at the Chicago Meeting, May, 1884 (p. 163 of the present volume), for the estimation of phosphorus in iron and steel, I employed samples of steel obtained from one works only, and of a given brand. Since then I have had frequent occasion to test the process on other steels, and find that it works equally well. But some steels present certain colors which may mislead the operator; and I therefore propose a slight change in the directions formerly given. On the second page of my paper, in the second paragraph, I would substitute the following modified directions: Place the flask under the hydrant, till the solution is perfectly cold ; then add, gradually, strong ammonia, with constant stirring, till the solution is changed into a pasty mass and the ammonia is in slight excess; then add cautiously HNO3 (1.40 specific gravity)

Jan 1, 1885

By W. N. Lacey, B. H. Sage

In recent years there has been an increase of interest in the flow of gases at relatively high pressures. Hydrodynamic calculation of the energy losses in the flow of gases in conduits, as well as through the porous solid materials constituting natural petroleum reservoirs, requires a knowledge of the viscosity of the fluid at the pressure and temperature involved. Although there are numerous publications concerning the absolute viscosity † of hydrocarbon gases at atmospheric pressure, there appears to be little information available relating to the effect of pressure upon the viscosity of these gases. Voge133 determined the viscosity of methane at 32° F. and atmospheric pressure. His measurements at 32° F. were later substantiated by the measurements of Rankine and Smith20 at 63° and 212° F. Ishida14 also reported values for the viscosity of methane at atmospheric pressure. Trautz and Kurz30 measured the viscosity of propane at atmospheric pressure, from 83° to 530°F., by the use of a short capillary tube. Rap-penecker2' determined the viscosity of gaseous isopentane at elevated temperatures. Day6 made an accurate investigation of the effect of pressure upon the viscosity of n-pentane and isopentane at pressures from 2 lb. per sq. in.‡ to the vapor pressure at 77° F. (approximately 9.8 and 13.3 lb. per sq. in., respectively). Earhart7 reported data upon the viscosity of several natural gases measured by the long capillary-tube method. The viscosity of air, at atmospheric pressure and 73.4° F., was measured by Harrington9 by the rotating-cylinder method. Kellstrom15 has rec,ently made an elaborate investigation of the viscosity of air at atmospheric pressure. The latter work is perhaps the most accurate investigation of the viscosity of a gas that has been made.

Jan 1, 1938

By Alden Greninger

MANY recent contributions in the field of theoretical metallography have been concerned with crystallographic definitions or descriptions of various phenomena. The lattice orientation of the crystal being studied must be known before such definitions can be made. Practically all the metallic crystals used do not have crystal faces-other than the unknown "plane of polish"; hence resort must be had to other means of determin-ing orientations. Some use has been made of etch-figures, slip bands, optical properties, etc., for this purpose; but for. accurate results, and because of the fewer restrictions to their use, the various X-ray methods have been the most satisfactory.1 The methods that, have been used may be divided into two general classes: (1) oscillation methods, and (2) transmission Laue methods-2

Jan 1, 1934