Search Documents

By John Towers, Paul A. Beck, W. D. Manly

Recent work on grain growth in high purity aluminum and in a solid solution type alloy of aluminum and magnesium1 showed that the isothermal increase of the average grain diameter D with time follows the equation D = K(tg + A)2 Eq 1 Here tg is that portion of the total annealing time 1, which is available for grain growth, that is the annealing time less the time necessary for complete recrystallization. The parameters A and n depend only on the temperature. A has the dimension of time, and is usually of the same order of magnitude as the time for recrystallization: R. In some instances R may be substituted for A in Eq I. This is the case for example at long periods of annealing or at high temperatures, where both A and R become small in comparison with t. In such instances Eq I is simplified to D = K, tn Eq 2 For high purity aluminum the exponent n increases in the ratio of about I to 5 in. the temperature range of 350' to 6w°C. 70-30 brass has been long known to exhibit grain growth of the continuous type, such as occurs in pure metals. For this reason, it was of interest to determine whether grain growth in brass also follows Eq I and 2 as it does in aluminum. Isotherma1 grain growth data for 70-30 brass were published in recent years by R. S. French2 and by H. L. Walker.' Fig I shows a log D vs. log t plot of French's data, together with the 500, 600 and 700°C data by Walker for 42.8 pct reduction by rolling. In such a log D vs. log t plot Eq 2 corresponds to a straight line with a slope of n. As seen in Fig I, the data of French and the 600°C data of Walker can be represented by straight lines. However, the 500 and 7c0°C data of Walker give curved lines and the average slope of his 500°C line is very different from the slope of the line representing French's data for the same temperature. Furthermore the curvature of the 700°C line suggests a tendency for grain growth to stop after 8 hr. If confirmed, this would constitute a definite deviation from Eq 2, not explainable on the basis of the specimen thickness effect found in high purity aluminum.' Walker's specimens were 0.125 in., or 3.18 mm thick, while the deviation occurs at a grain size of approximately 0.4 mm. A further point of divergence arose recently, when J. E. Burke suggested4 on the basis of Walker's data, that, instead of Eq 2, grain growth in 70-30 brass follows the equation D - D, = K . tgn Eq 3 Here D, is the grain size as recrystallized at the temperature in question. Although it was possible to show5 that, for pure aluminum, for which isothermal grain growth has been carefully investigated, Eq 3 is incompatible with the experimental facts, the situation remained somewhat obscure with respect to 70-30 brass. In view of the discrepancies between the published data on brass from different

Jan 1, 1949

By C. A. Stetefeldt

FoR the convenience of those who do not care to enter into the details of this long essay, I begin with a summary of the most important results it presents. The extraction of silver by the lixiviation-process from ores which have been subjected to a chloridizing-roasting, is based upon the fact that silver chloride is easily soluble in solutions of sodium or calcium hyposulphite, and that silver is precipitated from such solutions by an alkaline sulphide, with regeneration of the hyposulphite salts. In case the ore contains lead a large portion of the latter is and dissolved, lead sulphate being soluble in hyposulphite solutions. If, at the same time, copper is present, the sulphides precipitated from the solution, contain silver, copper, and lead, a combination of metals not desirable for subsequent treatment. Mr. E. H. Russell, of Park City, Utah, is the inventor and the patentee in the United States and several foreign countries of a new lixiviation-process, based upon the chemical facts discussed in this paper. Mr. Russell has discovered that lead can be completely separated from a sodium hyposulphite solution, as lead carbonate, by sodium carbonate or purified soda-ash, without precipitating any copper or silver. After decanting the solution from the lead carbonate, silver and copper are obtained from it in the usual way. This method of separating lead prohibits the use of calcium poly-sulphide as a precipitant for the sulphides, because any calcium entering the regenerated lixiviationsolution would also be precipitated as a carbonate with the lead by soda-ash. Hence, a sodium sulphide must be employed. A full investigation has demonstrated that this is by no means detrimental. Sodium sulphide and hyposulphite are more advantageously used in the lixiviation-process than the corresponding calcium-salts. Another defect in the lixiviation-process consisted in the necessity of a very perfect chlorination of the silver in the ore, because silver in

Jan 1, 1885

By AIME AIME

COMMITTEES. CENTRAL GENERAL COMMITTEE.-Wm. Fleet Robertson, Chairman; Win. M. Brewer,. Secretary. LOCAL COMMITTEE OF NELSON, B. C.-A. S. Farwell, Chairman; W. C. Bayly, Secretary; William Blakemore, M. S. Davys, S. S. Fowler, R. R. Hedley, Leslie Hill, A. H. Telly; W. C E. Koch, J. J. Campbell. LOCAL COMMITTEE OF ROSSLAND, B. C.-His Worship Mayor Hamilton, Chairman; AV. H. Aldridge, Charles Biesel, H. H. Claudet, F. W. Guernsey, R. Marsh, J. W. Astley, R. W. Brock, A. A. Cole, A. G. Larsen, R. H. Stewart. Also the Rossland Board of Trade, Robert Hunter, President; K. E. Mackenzie, Vice-President; A. B. Mackenzie, Secretary. LOCAL COMMITTEE OF GRAND FORKS, B. C.-His Worship Mayor Hammor, Chairman ; A. W. B. Hodges, A. L. White, G. M. Fripp, L. A. Manley, W. T. Spier, G. W. Wooster. LOCAL COMMITTEE OF VICTORIA, B. C.-Wm. Fleet Robertson, Chairman; William Al. Brewer, Secretary; Harold Grant, Thomas Kiddie, Clermont Livingston, E. C. Musgrave, W. J. Sutton, Francis A. Thomson. LOCAL COMMITTEE OF VANCOUVER, B. C.-C. F. Jackson, Chairman; His Worship Mayor F. Buscombe, J. J. Banfield, A. Bethune, John Boyd, H. C. Clarke, A. B. Erskine, E. P. Gilman, William Godfrey, W. D. Haywood, R. K. Houlgate, H. T. Lockyer, J. I. McAdam, H. M. McDowell, C. W. McMeekin, W. H. Malkin, F. Richards, T. J. Smith, George A. Walkem, G. Slieldon Williams. LOCAL COMMITTEE OF WHITE HORSE, Y. T.-Robert Lowe, Chairman.; T. W. Jackson, Secretary; George -Armstrong, A. L. Bindley, Rev. Father Corbeil, L. De Gex, A. E. Fisher, W. P. Grainger, P. D. McMillan, Rev. Mr. Main, George C. Mallot, Alfred Parre, George Pulham, George Reid, William Robinson, J. P. Scharschmidt, J. C. Schraeder, Major A. E. Snyder, Rev. Mr. Stringer, Judge George L. Taylor, William Taylor, H. Wheeler, E. J. White, J. P. Whitney;' ; LOCAL COMMITTEE OF DAWSON, Y. T.-Hon. W.W. B. McInnes, Commissioner of the Yukon Territory, Honorary Chairman; Major Z. T, Wood, Assistant Commissioner of the Yukon Territory, Honorary Chairman; J. B. Tyrrell, Chairman; J. Moore Elmer, Vice-Chairman; George Black, Secretary; Hon. Mr. Justice Dugas, Hon. Mr. Justice Macaulay, Hon. Mr. Justice Craig, Dr. Alfred Thompson, D. A. Cameron,. E. W. Griffin. The first session, held in the ministers' room of the Parliament Building, 3 p.m., Saturday, July 1st, was presided over by Past-President Robert W. Hunt. His Excellency the Lieut.-

Nov 1, 1905

By T. D. Yensen

Discussion of the paper of T. D. YENSEN, presented at the New York meeting, February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 483 to 512. JOHN A. MATHEWS, Syracuse, N. Y.-Concerning the critical composition of the steel containing 2.50 per cent. of silicon, I may say that 12 or 13 years ago we made some of these alloys. They. were not as pure as the alloys made by Mr. Yensen, nor were they melted in vacuo, but one of them contained exactly 2.50 per cent. silicon, and about 0.25 per cent. carbon. It gave us no trouble whatever in hammering to a billet or rolling into bars, nor even when rolling into ¼ -in. wire rods. The steel in question was practically free from everything except carbon or silicon and contained no manganese sulphur or phosphorus worth mention. The alloy containing 2.50 per cent. of silicon worked perfectly well, as well as one containing 0.5 per cent. silicon, and it seems to me that further work should be done by Mr. Yensen on the physical properties of alloys at this seemingly critical change point. W. E. -RUDER, Schenectady, N. Y.-We -have made silicon steels of practically every composition and have never obtained any material under 5 or 6 per cent. of silicon which was brittle. This may be due, of course, to the presence of carbon, in some of the 'commercial materials, and I presume that Mr. Yensen would argue that the: presence of this carbon might prevent inter-granular brittleness. However, all of our silicon steels, up to 5 per cent. of silicon, by treatment in hydrogen at temperatures near the melting point, can be made to show inter-granular brittleness. Furthermore, the material made brittle in this way could be restored by treating at the same temperature in hydrogen containing a hydrocarbon vapor. I discussed this matter some years ago in a paper on inter-granular cement. It therefore appears likely to me that Mr.

Jan 5, 1916

By C. O. Lee, Z. W. Bartlett, R. H. Feierabend

DESPITE the fact that American brimstone production has increased 2 ½ times since the prewar period 1935-1939, the demand for sulphur exceeds the supply. To alleviate this situation efforts are being made to increase the production of sulphur and bring the shortage to an end. The most important developments are being undertaken on the Gulf Coast. One new brimstone mine has been put into operation and three others are being developed. These projects are expected to account for a large part of the additional sulphur production now anticipated for the free world.1,2 Except for a small amount of byproduct sulphur from sour natural gas and refinery gases, American brimstone is produced by the same process devised by Frasch 60 years ago, consisting essentially of the injection of superheated water at about 325°F into sulphur-bearing formations through wells which are drilled from the surface by standard oilfield methods. Sulphur deposits vary in depth from a few hundred feet to 2500 ft from the surface; in a typical deposit the sulphur occurs as crystalline aggregates in porous limestone and gypsum in concentrations varying from 5 to 40 pct, the thickness of the formation ranging from a few feet to several hundred.3 The deposits are usually surrounded by formations impermeable to the flow of hot water, the top and sides being enclosed by impermeable sediments and the bottom by dense impermeable anhydrite. As the hot water leaves the well bore, it percolates through the formation and transmits its heat to the rock and sulphur. When the sulphur reaches 240°F it melts, separates from the rock, and flows through the hot channels downward to the bottom of the well. Here it is freed from incoming water and from formation water, which saturates the porous rock, by gravity separation, liquid sulphur being 1.8 times as heavy as water. It then is pumped to the surface in a relatively pure state, 99.5 pct or better. Chief contaminants are organic impurities, such as petroleum residues, which are soluble in sulphur and tend to discolor it.4 Sixteen deposits of commercial magnitude have been discovered in the Gulf Coast area. Five of these deposits have been depleted and abandoned with production totalling more than 26,886,000 tons. Eight properties are operating and have produced 65,875,000 tons to Jan. 1, 1952, for a total Frasch-type production of 92,761,000 tons. Three new deposits are under development. Aforementioned deposits are listed in Table I. Each of these deposits has been found in the caprock overlying shallow intrusive salt plugs or domes and buried in several hundred to as much as 2500 ft of sediments. All salt domes do not contain sulphur; only 16 sulphur deposits have been found in a total of 231 salt domes which are known to exist in the Gulf Coastal states of Texas, Louisiana, Mississippi, and Alabama. Ten of the salt domes lie in the Gulf of Mexico offshore from the Texas and Louisiana coasts. Additional offshore domes may be found, but their value as a sulphur potential is questionable owing to the great hazard and high cost that can be visualized at these exposed locations where depths of water reach 50 ft. Marsh operations of Freeport Sulphur Co. are in the southeast section of Louisiana. In general, the country is low, flat, relatively uninhabited marshland broken by many shallow lakes and bayous which extend for irregular distances inland. Geologically, the coastal area is of sedimentary origin, having been built up gradually under the sea by deposition of material carried down by large streams to their deltas. Offshore bars were formed enclosing

Jan 1, 1952

By Walter E. Heinrichs

The following is a condensed version of an open letter addressed to Bil Gilbert of Sports Illustrated: Your article, "When a Law Fights a Law, Sports Illustrated. April 26, 1971, betrays considerable unfamiliarity with the subjects of ecology, social science, mining law and history. In a magazine as widely circulated as Sports Illustrated, an article of such a slanted nature misleads the general public.

Jan 1, 1971

By A. J. Mcintosh

PRICE changes in competing fuels in the last three decades have reflected the changes in the consuming habits of the people of the United States. Prior to World War 11 the importance of fuel oil and fuel gas increased almost constantly while the relative importance of both bituminous and anthracite coal decreased. During this same prewar period coal prices increased to a much greater extent than oil prices. In fact, in many years, oil prices declined and in most cases are now no higher than they were back in 1925-26. During the war natural economic trends were entirely upset because of the tremendous petroleum requirements of the Army and Navy. Under these conditions many industrial plants were converted to the use of coal and the new installations in home heating and industrial plants of all kinds which might have used oil were practically eliminated. Although petroleum prices were rigidly controlled by OPA coal prices increased several times during the war. An over-all statement as to the rela-

Jan 1, 1947

By G. A. Savanick

Borehole (slurry) mining, where a tool incorporating a water-jet cutter and a downhole slurry pump mines phosphate through a borehole, was field tested in northeastern Florida as part of a US Bureau of Mines program to increase the domestic availability of critical minerals. About 1.5 kt (1700 st) of phosphate ore were mined at 23.6 t/h (26 stph) from a depth of 76 m (250 ft). The borehole was filled with water during mining for roof support and to assist slurry pumping. Underwater cutting was enhanced with an air-shrouded water jet. Mined cavities were backfilled to prevent subsidence after abandonment. Roof subsidence during mining was avoided only when the cavity was filled with water. Environmental monitoring before, during, and after mining included hydrological studies and measurements of water quality. Significant water quality changes occurred only in the zone being mined and were confined to the immediate area of the borehole.

Jan 1, 1986

By H. W. McQuaid, E. W. Ehn

It is usually assumed that chemical specifications are sufficient for steel to be used for case carburizing, and if the steel analyzes within the ordinary limits specified for steel for this purpose, no difficulty traceable to the steel used should be encountered in obtaining satisfactory results in the case carburizing and hardening. Much work has been done to determine the effect of various alloying elements on the rate of carbon penetration, etc. but, to our knowledge, little if anything has been published in regard to the effeet of the quality of the steel on the final results in the hardening of case-carburized steel parts. The writers believe that the structure of the case both before and after quenching is greatly affected by the actual condition of the steel itself as made, and that for good results in the case-carburizing and hardening departments, the steel should be of the best possible quality as regards non-metallic impurities. It is the purpose of this paper to prove that the presence of excess dissolved oxides in the steel, as made in the melting furnace, affects permanently the results obtained in carburizing and hardening and that it is possible that the presence of dissolved oxide call result in total unfit-ness of low-carbon steel for case hardening purposes. When races and rolls for roller bearings are made from a low-carbon steel, case carburized and hardened, it is of primary importance that the results of this treatment be of the highest quality. It is necessary, therefore, that in the case-carburizing work each detail be rigorously checked to avoid any defects which would cause the loss of much time and material. The case carburizing with which this paper deals was done in under-fired oil furnaces. The temperature of each furnace is controlled by means of a platinum platinum-rhodium thermocouple, in connection with a potentiometer indicator and potentiometer recorder. The temperature of each furnace is registered every 15 min. by an operator, who is continually checked by the automatic recorders.

Jan 1, 1922

By H. W. McQuaid, E. W. Ehn

It is usually assumed that chemical specifications are sufficient for steel to be used for case carburizing, and if the steel analyzes within the ordinary limits specified for steel for this purpose, no difficulty traceable to the steel used should be encountered in obtaining satisfactory results in the case carburizing and hardening. Much work has been done to determine the effect of various alloying elements on the rate of carbon penetration, etc. but, to our knowledge, little if anything has been published in regard to the effeet of the quality of the steel on the final results in the hardening of case-carburized steel parts. The writers believe that the structure of the case both before and after quenching is greatly affected by the actual condition of the steel itself as made, and that for good results in the case-carburizing and hardening departments, the steel should be of the best possible quality as regards non-metallic impurities. It is the purpose of this paper to prove that the presence of excess dissolved oxides in the steel, as made in the melting furnace, affects permanently the results obtained in carburizing and hardening and that it is possible that the presence of dissolved oxide call result in total unfit-ness of low-carbon steel for case hardening purposes. When races and rolls for roller bearings are made from a low-carbon steel, case carburized and hardened, it is of primary importance that the results of this treatment be of the highest quality. It is necessary, therefore, that in the case-carburizing work each detail be rigorously checked to avoid any defects which would cause the loss of much time and material. The case carburizing with which this paper deals was done in under-fired oil furnaces. The temperature of each furnace is controlled by means of a platinum platinum-rhodium thermocouple, in connection with a potentiometer indicator and potentiometer recorder. The temperature of each furnace is registered every 15 min. by an operator, who is continually checked by the automatic recorders.

Jan 1, 1922

By Alfred Boyles

"Heredity"1 in cast iron has been a subject of much discussion. Numerous experimenters have found that the properties of gray iron may vary greatly without corresponding variations in composition or thermal treatment. The main structural difference in such cases is in the size and distribution of the graphite flakes and the explanations given usually attribute this difference to some chemical element not shown by ordinary analysis or to some physical factor, such as inclusions in the melt. It cannot be said that any of these theories is completely satisfactory. Much remains to be learned about cast iron and for this reason a study of the material was undertaken as a part of the program of fundamental research at Battelle Memorial Institute. A review of the literature indicated that very little systematic work had been done on the mechanism of freezing in cast iron. The experiments described below are largely concerned with that problem. Normal and "Dendritic" Cast Iron As examples of variation in type of structure, photomicrographs of two test bars of cast iron are shown (Figs. 1 and 2) and the composition and properties are given in Table 1. Both are common, unalloyed gray iron. Test bar No. 13 has normal graphite flakes while No. 49 has very fine, lacy graphite arranged in a dendritic pattern, the matrix in both being pearlite. These two types of cast iron are well known to foundry-men and need no detailed description.

Jan 1, 1937

By C. Graeme-Barber, R. L. Bell, T. G. Langdon

An analysis is made of the formulas and ,methods used to estimate the contribution of grain boundary sliding to the overall strain of a polycrystal. The errors involved in the approximations and/or ,mistakes in earlier work are assessed quantitatively so as to make possible the critical use of previously published data. SINCE it has been found that, under conditions of very slow creep, the strain due to grain boundary sliding (?gb) may contribute as much as 80 pct of the total creep strain,1,2 it is obviously important to have reliable methods for estimating this grain boundary strain. In two recent papers Stevens3,4 has drawn attention to the pitfalls encountered in assessing ?gb. He criticizes 1) the assumptions made in the derivation of some of the formulas for ?gb, and 2) the indiscriminate averaging procedures used for obtaining the quantities substituted in these formulas. These and further criticisms of earlier work are mostly valid. Unfortunately the only formulas and procedures recommended are either impossible or very difficult to apply in practice. Furthermore no attempt is made to assess the errors involved by the earlier approximations or mistakes, and so it is not possible to make critical use of any of these early dab. The present article attempts to improve on these shortcomings by reference to empirical verification of easily applied formulas whose theoretical derivations involve some otherwise unjustifiable assumptions, and by a quantitative assessment of the errors in previous work. DEFINITIONS First it is necessary to define the terms and symbols to be used. The choice of symbols preferred here is a logical combination and extension of the v introduced by McLean5 and the u by Brunner and rant.' In Fig. 1 the two grains X and Y are displaced by the sliding vector AC. u is the component of sliding resolved along the stress axis, v is that measured perpendicular both to the stress axis and to the specimen surface, and w is that measured perpendicular to the stress axis but in the plane of the surface. Two angles define the orientation of the grain boundary: 8, between the stress axis and the surface trace of the boundary, and +, the internal angle on a longitudinal section cut perpendicular to the surface. In computing the strain resulting from the boundary displacement at all the in- dividual boundaries in a polycrystal the components u, v, or w are sometimes averaged along a longitudinal line (i.e., parallel to the stress axis), sometimes along a transverse line, and sometimes at randomly chosen boundaries. Averages obtained in these three ways are given subscripts 1, t, and r, respectively. Stevens rightly calls attention to the possibility of non-equiaxed grain shapes either at the start or at the end of deformation. In this article all values of numbers of grains per unit length will refer to measurements made before deformation. The subscripts 1 and t will be used for the number of grains per unit length obtained along longitudinal and transverse lines, r for that obtained by averaging along a number of randomly directed lines. FORMULAS FOR ?gb ?gt, as a Function of u. An obvious truth is that cgb can, in principle, be obtained by summation of all the v components at the boundaries intersected by a longitudinal line of known length I, viz.: where nl is the number of grains per unit length, parallel to the stress axis, in the unstrained specimen. There are assumptions in the analytic derivation of Eq. [I] due to Brunner and rant' but ~achinger' arrived at Eq. [la] by a rigorous method. Unfortunately the experimental procedure required by Eq. [ la] proves very difficult as boundary migration tends to obscure the points at which the longitudinal line meets the grain boundary and the errors on such measurements tend to be large, see Fig. 2. For example, on a specimen of Magnox AL 80 at a creep strain of 9.7 pct, 300 measurements of u obtained from the points of intersection of a longitudinal line with the grain boundaries gave ul = 8.95 ± 3.58 pm, or an error of ±40 pct, at the 95 pct confidence limit. These large errors due to migration may be avoided by measuring u from the separation of the segments

Jan 1, 1968

By E. T. Turkdogan, P. Grieveson

It is shown experimentally that, by making use of the coupled S-O reaction in ionic melts, it is possible to transfer slclJur or oxygen from a lozv to a high chemical potential through an ionic nzenzbrane. This uphill transfer of sulfur is accompanied by a counter downhill transfer of oxygen and vice versa. The Materials balance shows that the amoulits of sul -fur and oxygen lost or gained by one system are the same as those gained or lost by the other systenz — the two systejns being separated by an iofzic membmne. The systems used in these experi?nents were solid Mn-MnS-Mno and liquid Fe-S-0. Sufficient results were obtained Lo study the kinetics of the transfer and the indications are that the counter diffusion of sulfide and oxide iojzs in the membrane is the rate controlling process. WHEN an ionic oxide-melt reacts with an atmosphere containing sulfur and oxygen-bear ing gases the following reaction occurs: 1/2 S2 (gas) +O2- (melt) = S2- (melt) + 1/2 0, (gas) [1] Under the restrictions that i) electric conductance in the melt is purely ionic and ii) each constituent element in the melt does not change valence, the solution of an atom of sulfur in the melt will result in the evolution of an atom of oxygen, so that the electric neutrality is maintained. For a given temperature and melt composition, the equilibrium concentration of sulfur in the melt is determined by the ratio, po2 /ps2 , in the gas phase and not by the individual partial pressures of oxygen and sulfur. This has been demonstrated by a number of investigators, for example by Richardson and withers', Fincham and Richardson,la by St Pierre and Chipman,' and by Turkdogan and Darken.3 In his Howe Memorial Lecture for 1961, Darken discussed the possibility of uphill pumping of sulfur through an ionic membrane at the expense of oxygen. TO test the validity of this concept associated with coupled reactions, experiments were carried out in the following manner. A presintered mixture of Mn-MnS-MnO and prefused mixture of Fe-S-0, contained in platinum and iridium crucibles, respectively, and separated by a thin layer of soda-glass (to act as an ionic membrane), were placed side by side in an evacuated silica capsule and sealed. This was then kept at 1400°K for a required time to allow Reaction [11 to occur via the ionic membrane. When partial equilibrium is reached, the ratios Po2 /pS2, for systems on either side of the membrane, are equal and the flux of sulfur and oxygen through the membrane becomes zero, although the individual partial pressures po2 andp,, in these two systems may differ considerably.

Jan 1, 1962

By Bert Sandell

MUCH has been said and written about the various uses of die-castings, their applications in the various industries and their advantages and disadvantages. Examination of this literature, however, fails to disclose any data concerning the effect of temperature upon any of the physical properties of die-casting alloys. The uses and applications of die castings are so numerous, and of such a varied nature, that far too lengthy a manuscript would be required to list all of them. Brief mention of some specific cases will suffice to illustrate the temperature ranges in which certain die castings function. Automobile hardware, such as hub caps, door handles, radiator caps, etc., can be used as one example. Castings of this type are constantly exposed to varying climatic conditions, temperatures ranging from below zero to upwards of 100° F. Refrigerator parts, such as ice-cube trays, etc., form another example. Approaching the other temperature extreme, we encounter conditions such as are found in kitchens in which oven-heat indicator parts, cooking utensils, waffle grids, etc., embody use of die castings, where temperatures as high as 500° F. are often met with. Because of this variation in service temperatures, it was felt necessary to ascertain the effect of these temperatures upon the physical properties of die-casting alloys. The Charpy impact test was chosen first because of its simplicity, and because of the fact that brittleness is more likely to be objectionable in die castings than hardness or other physical properties.

Jan 1, 1932

By Herbert Clark Hoover, Lou Henry Hoover

MOST illustrious Princes, often have I considered the metallic arts as a whole, as Moderatus Columella2 considered the agricultural arts, just as if I had been considering the whole of the human body ; and when I had perceived the various parts of the subject, like so many members of the body, I became afraid that I might die before I should understand its full extent, much less before I could immortalise it in writing. This book itself indicates the length and breadth of the subject, and the number and importance of the sciences of which at least some little knowledge is necessary to miners. Indeed, the subject of mining is a very extensive one, and one very difficult to explain ; no part of it is fully dealt with by the Greek and Latin authors whose works survive ; and since the art is one of the most ancient, the most necessary and the most profitable to mankind, I considered that I ought not to neglect it. Without doubt, none of the arts is older than agriculture, but that of the metals is not , less ancient ; in fact they are at least equal and coeval, for no mortal man ever tilled a field without implements. In truth, in all the works of agricul- ture, as in the other arts, implements are used which are made from metals, or which could not be made without the use of metals ; for this reason the metals are of the greatest necessity to man. When an art is so poor that it lacks metals, it is not of much importance, for nothing is made without tools. Besides, of all ways whereby great wealth is acquired by good and honest means, none is more advantageous than mining ; for although from fields which are well tilled (not to mention other things) we derive rich yields, yet we obtain richer products from mines ; in fact, one mine is often much more beneficial to us than many fields. For this reason we learn from the history of nearly all ages that very many men have been made rich by the

Jan 1, 1950

By Neville J. Price

In order that the reader may not be misled, I feel it necessary to comment upon the title of this paper. "Laws of Rock Behavior," one may take as being part of the all-embracing "Law of Nature" and this, according to the Oxford Dictionary, relates to the principles of conduct recognized as being pleasing to God. I feel it would be presumptuous to erect a code of rock behavior on this basis, so turn to a secondary definition, namely that a "Law" is that which is intrinsically reasonable. It is extremely unlikely that any group of geologists, or workers in rock mechanics would be in complete agreement about what could be taken to be "intrinsically reasonable." Therefore, this paper does not present any deified utterances, but rather deals with a few aspects of rock behavior which I consider to be intrinsically reasonable and with which I hope the reader will concur. The mode of behavior of rocks in the Earth's crust covers the range from wholly brittle to completely ductile ; with a deformation time scale which may be measured in milliseconds, for some events such as meteoritic impact, or in millions of years for the tectonic deformation involved in mountain building. A complete survey is, of course, outside the scope of an introductory paper, so I must be both brief and selective in my treatment. Any attempt to establish the mode of rock behavior in the Earth's crust should take into account data and relationships established in laboratory experiments and correlate these with field evidence. Consequently, the first section of this paper presents a brief discussion of the experimental aspects of rock mechanics which are pertinent to the subsequent discussion.

Jan 1, 1970

By H. E. Montgomery

Engineering trends for some years have been toward higher temperatures, both in process work and in steam generation. Progress in design has been dependent upon the development and evaluation of suitable alloys. Elementary knowledge of the limitations of copper-base alloys indicate their unsuitability for the higher ranges of operating temperatures; say, for steam to 950°F. Emphasis upon the more severe conditions perhaps is a reason why more complete evaluations have not been made for copper-base alloys over their range of suitability. However, the few studies made show clearly the need for more accurate evaluations. Some copper-base alloys long looked upon favorably because of superior room-temperature properties are not as desirable as some others perhaps not so "strong" and "hard," as measured by usual acceptance tests. Load-carrying capacity and structural stability arc two important factors. Structural stability as influenced by temperature, by presence of corrosive media, or by the effects of stress itself, frequently is a limiting factor. An early reference to creep properties of the cast copper-base alloys is that of Brown1 (Admiralty gun metal, Cu 87.5, Sn 10.1, Zn 2.3 and Pb 0.08). His tests were similar to present-day stress-rupture tests without measurement of creep elongrttion. Loading was in steps with usually 24 hr. between steps, and continued until failure. He advocated a "useful strength value" of 61/2 tons (I4,560 Ib.) per sq. in. at 572°F. (300°C.). A specimen broken in 1/2 hr. at 572°F. had a strength of 21 tons (26,880 Ib.) per sq. in. The strength values as determined by 1/2-hr. tests and those by the longer stress-rupturc start to differentiate at 392°F. (200°C). This is the temperature at which time at load began to play an important part. Bolton, Price and Hebemann2 give creep curves on 88-10-2 (A.S.T.M. B-60, CU 88, Sn 10, Zn 2) and steam or valve bronze (A.S.T.M. B-6I, Cu 87.50, Sn 6.00, Zn 3.75, Pb 1.70) at 500°F. Direct comparison of the two alloys under 7500 lb. per sq. in. stress showed the steam bronze (A.S.T.M. B-61) superior in creep strength to the 88-10-2 (A.S.T.M. B-60). The steam bronze shows no creep after 700 hr. (1540-hr. test). The 88-10-2 shows a rate of about 7.0 per cent in 100,000 hr. over the last 700 hr. of the test. Creep curves on the steam bronze are also given at the same temperature (500°F.) with loads of 6500 lb. per sq. in. and 8000 lb. per sq. in. These indicate "creep strengths" (creep rate within I per cent in 100,000 hr.) in excess of 8000 lb. per sq, in. for this alloy. It was found that higher percentages of tin are detrimental to creep resistance. This is caused by the presence of or formation during test of considerable alpha-delta eutectoid in the higher tin alloys. Bolton also states that the high

Jan 1, 1945

By J. R. Campbell

THE need for standardizing methods of arriving at definite conclusions regarding the cleanability of a given coal, and for measuring the performance of coal-cleaning equipment, is constantly increasing. Earlier notes by the author on this subject are amplified in this paper, because he believes that better preparation of bituminous coal is a partial solution of the coal operators' troubles. WASHABILITY STUDIES The term "washability" of coal was coined when washing was the universal method of separating coal from its impurities by utilizing their difference in specific gravity. This and analogous terms are still used in their broad sense although pneumatic or air separation is now used to clean coal. These terms are so used in this paper. Too much time or money, can hardly be spent on "feed surveys" to get a "picture" of the coal that is to be cleaned. There have been too many "rule of thumb" methods used. Screen analyses and "sink-and-float" tests on the raw coal enable the coal operator and washery man to predict within reasonable limits the results that may be expected from any efficient cleaning apparatus.

Jan 1, 1928

THE CHAIRMAN.-Thank you. Since the papers are rather closely related, I think rather than taking them one at a time we will entertain discussion on any of these problems at this time. W. A. REICH.*-We, of course, quite a while ago got the yellow light that Mr. Cole spoke of, and like everyone else immediately started to study silicon bronzes and brasses. We were interested in the silicon bronzes and brasses because we felt that in order to replace gun metal which makes up a large part of our use we needed something with an elastic limit at least equal to that of gun metal. That means at least 12,000 lb. per sq. in. This study was aimed only at tin conservation. Then we dropped the study of silicon bronzes because high purity copper which is needed in their manufacture became a scarce item. To make a long story short we have recommended to our designing engineers that they use 85-5-5-5 wherever possible because 85-5-5-5 we understand can be made entirely from scrap with little or no tin addition. 85-5-5-5 has a lower elastic limit than 88-8-4, so we felt that we would need another substitute material, a structural alloy with an elastic limit equal to that of 88-8-4, and we immediately turned to the manganese bronze type of alloy. The poor foundry properties of standard manganese bronzes were mentioned by Mr. Thieme and since we feel that high zinc content is largely responsible for this difficulty, our development is directed along the lines of uncovering a material with a lower zinc content and which gains its elastic strength from the addition of other alloying elements, such as, aluminum, manganese and iron. It must be possible to make this alloy entirely from scrap with no additions of scarce high purity material. I would appreciate an expression of opinion on how low we can go in zinc content with this type of alloy without seriously impairing the availability, and how high we can go in aluminum content without making use of aluminum restricted for that use. We assume that the maximum lead content must be placed at 1 ½ per cent to insure good availability and we feel that about I per cent of tin in the alloy would improve salt water corrosion resistance similar to the effect of tin in Admiralty Metal. Has anyone here had experience with the effect of tin and lead on the weldability of such an alloy? C. S. COLE.-What percentage of lead and tin? W. A. REICH.-About 1 per cent of lead and 1 per cent of tin. We are studying the weldability of the alloy but perhaps someone already has the answer. (Pause, no answer) The claim has been made that 1 per cent of lead can be added to certain silicon bronzes without impairing their properties. A silicon bronze with a low zinc content requires high purity copper in its manufacture but if say the 15 per cent zinc, 44 silicon balance copper alloy could be made, with a I per cent lead content, some quantity could be made from scrap. We do not know whether the aforementioned is

Jan 1, 1943