Search Documents

By Herbert Johnson

DURING the past 10 or 12 years very little information has been made generally available concerning the commercial possibilities of separating materials by means of static electricity; and yet during that same period important improvements have been made in various branches of the science of electricity, which, when taken together, and applied to electro-static separation, have resulted in important improvements in that art as well. For example, much improvement has been made in high-voltage electrical equipment such as full-wave vacuum-tube rectification and improved mechanical rectification. Great strides have likewise been made in the development of insulators for high-voltage work, not only in the materials used but also in the design of the insulators themselves. Again, in another field, the development of air-conditioning equipment has improved the technique of controlling the surface condition, through drying or humidifying, of the various materials that are passed through the electrostatic separator. In many authoritative publications and textbooks, the electrostatic separation process is declared to require a balance far too sensitive for general commercial application. For example, one publication1 in the past has referred to an unfavorable effect on the process caused by varying atmospheric conditions such as humidity. Some2 have even gone so far as to state that sunlight and shadows may seriously affect the separating efficiency of the process. Such statements may have been true in the early development of the art, when the source of static elec-tricity was derived from a friction disk machine, such as the Wimshurst. The Blake Mosher equipment and the work of Huff in applying motor-generator sets, transformers and mechanical rectification overcame much of this kind of objection to the commercial application of the elec-trostatic separating process.

Jan 1, 1938

By E. G. Leonardon, D. C. McCann

The search for oil has required, and without a doubt supplies, a tremendous amount of information on the structure, composition, physical properties, and history of sedimentary rocks. The earliest and most complete source of knowledge is the sample or core of the rock itself, the uses of which are well known. The purpose of this paper is primarily to discuss a new method for obtaining these cores, and to illustrate its use in connection with electrical logs. Most cores have been obtained through a special adaptation of rotary drilling, and the results have been remarkably good, considering the mechanical problems involved. Unfortunately, because of the time and expense, this method cannot be used for the entire length of the drill hole. Even though ingenious contrivances have been evolved in order to reduce the time spent in round trips, such as wire-line coring equipment, mechanical coring still remains too expensive to be carried out continuously. In practice, therefore, one is finally compelled to estimate the probable depths of the more interesting horizons and, allowing a wide margin of safety, to core through those sections only. It is true also that interesting results have been obtained by examining the cuttings brought to the surface by the mud circulated in the well during the process of drilling. Be that as it may, the inescapable fact remains that key horizons may be passed inadvertently, for one reason or another, while the drilling operations are being performed. The only continuous record of the formations encountered is that furnished by electrical surveys. Obviously, it would be desirable to make the electrical survey first and to take the samples from the wall of the hole according to the indications on the electrical log. In this way, it would be possible to core only the exact sections desired, eliminating the otherwise inevitable estimates as to the point at which to start coring, and thereby reducing to a minimum this expensive operation. At the same time this method would provide a maximum of useful samples. A device for taking samples of the formation from the walls of a hole therefore offers the possibility of recovering cores from zones otherwise lost as a source of this type of information. Furthermore, by coring

Jan 1, 1939

By E. G. Leonardon, D. C. McCann

The search for oil has required, and without a doubt supplies, a tremendous amount of information on the structure, composition, physical properties, and history of sedimentary rocks. The earliest and most complete source of knowledge is the sample or core of the rock itself, the uses of which are well known. The purpose of this paper is primarily to discuss a new method for obtaining these cores, and to illustrate its use in connection with electrical logs. Most cores have been obtained through a special adaptation of rotary drilling, and the results have been remarkably good, considering the mechanical problems involved. Unfortunately, because of the time and expense, this method cannot be used for the entire length of the drill hole. Even though ingenious contrivances have been evolved in order to reduce the time spent in round trips, such as wire-line coring equipment, mechanical coring still remains too expensive to be carried out continuously. In practice, therefore, one is finally compelled to estimate the probable depths of the more interesting horizons and, allowing a wide margin of safety, to core through those sections only. It is true also that interesting results have been obtained by examining the cuttings brought to the surface by the mud circulated in the well during the process of drilling. Be that as it may, the inescapable fact remains that key horizons may be passed inadvertently, for one reason or another, while the drilling operations are being performed. The only continuous record of the formations encountered is that furnished by electrical surveys. Obviously, it would be desirable to make the electrical survey first and to take the samples from the wall of the hole according to the indications on the electrical log. In this way, it would be possible to core only the exact sections desired, eliminating the otherwise inevitable estimates as to the point at which to start coring, and thereby reducing to a minimum this expensive operation. At the same time this method would provide a maximum of useful samples. A device for taking samples of the formation from the walls of a hole therefore offers the possibility of recovering cores from zones otherwise lost as a source of this type of information. Furthermore, by coring

Jan 1, 1939

By W. A. Forbes

by the combustion of this gas as it reached the air was a familiar sight in the days when open-top furnaces were in vogue. As blast-furnace practice progressed, however, involving the use of hot blast and the development of power from the gas, blast-furnace construction was modified to conserve this gas for heating hot-blast stoves, raising steam under boilers, and various miscellaneous purposes. When the use of blast-furnace gas was extended to the driving of gas engines, the necessity for thoroughly cleaning the gas became apparent., and soon the advantages of also properly cleaning the gas for use in stoves and udder boilers became more fully recognized.

Jan 10, 1913

Jan 1, 1933

By S. P. Barber, G. W. Cutting, V. Alesse, M. Ciriachi

Just what is happening in the preparation and mineral separation stages are questions frequently asked about most processing plants. It is unusual to find the answers readily available in the operating metallurgical data. Knowledge is nominally available from metallurgical balances about the head ore grade, grade and recovery of the concentrates, and the plant tailings. However, the mechanisms which control grade recovery and losses are seldom monitored in such a way as to permit specific analysis: Thus, when questions about the effectiveness of the process are asked, the answers are based frequently upon intuitive professional judgments and local expertise. Detailed investigations of process functions are extensive in terms of manpower, time, and interference with production. An investigation method in which process operating conditions could be provided in a cost effective manner would assist in local process assessment and control. Such a collection of process operating data is defined as a process audit and the development of the necessary techniques forms the subject of this paper. A typical application to a lead-zinc concentrator highlights both the manner of implementing a process and the plant data made available for local use.

Jan 1, 1980

By H. R. Spedden, A. M. Gaudin, M. P. Corriveau

A preliminary study of silver ion adsorption by sphalerite in ion exchange column with influent electrolyte marked with radiosilver is described. Rapid ion exchange occurs at first followed by slow reaction controlled perhaps by solid state diffusion. One experiment with radiocopper instead of radiosilver is reported briefly. IT has been known for many years that sphalerite is floated after it has been activated by a metallic cation, particularly copper.' The activation of sphalerite by copper is known to be an exchange of an atom of copper for an atom of zinc at the surface of the sphalerite.2,3 It has been estimated from various guesses of the available mineral surface that the depth of the copper-bearing coating is of the order of thickness of one atom. However, the exact mechanism of the activation process is unknown. A number of metals other than copper act in the same general manner."' " In particular, it has been known that silver replaces zinc at the surface of sphalerite. As copper is usually divalent, whereas silver is monovalent, it may well be assumed that there are differences, perhaps major differences, in the detailed scheme of activation by these two cations. Furthermore, since silver has unusual photoelectric properties and may be a contributor to the fluorescence of sphalerite, a study of its activating mechanism might open up some interesting avenues for exploring these other phenomena. The choice of silver as an activator of sphalerite was suggested also by the fact that its radioactive tracer, silver 110, is particularly convenient in that it has a long half-life and is energetic enough to permit counting through a counter window. The experimental technique selected, therefore, included the preparation of solutions of silver nitrate con- taining a proportion of active silver nitrate sufficient to give convenient counting data. In further considering the method to be used, a desirable choice seemed the use of batch experimentation in which a given solution was allowed to act on a certain lot of mineral for a given length of time at a given temperature, this period of mutual reaction being followed by analyses of the separated solid and solution. But an alternative method seemed more attractive. This is the method now so familiar to the users of ion-exchange resins, which was first made famous by the Russian chromatographer, Tswett.6-8 It consists in forming the mineral into a porous column through which the solution is allowed to flow at a constant rate. The usual method of allowing a batch of solid to react with solution is the equivalent of a single plate distillation operation while the chromatographic or ion-exchange column is a multiple-plate method—the multiplicity of the plates being represented by the reciprocal of the rate of flow of solution through the column. It seemed to us that the chromatographic method had such

Jan 1, 1952

By J. A. Pusateri, M. A. Orehoski, N. R. Arant

Plant studies on commercial-size ingots and laboratory experiments with induction furnace heats have demonstrated that the major source of ingot cracks is associated with two conditions arising during top-pouring practice: 1—solidification during pouring, and 2—turbulence created by the impact of the stream. Methods of controlling the two factors were effective in eliminating or significantly reducing ingot cracks. BECAUSE the process of removing surface defects from hot-rolled product is so costly, the steel industry is striving constantly to develop methods of preventing, or at least decreasing, the occurrence of surface defects. Investigations have revealed steel-making and processing variables related to major surface defects, and controlling these variables has led to improvements in surface quality. However, the fundamental causes of major surface defects, such as ingot cracks, have not been determined; consequently such defects persist. At the Research and Development Laboratory of the United States Steel Corp. in Pittsburgh, a seam research program was initiated to determine the fundamental causes of certain major defects. As a part of the program, ingot cracks in killed, finegrained C1020 steel were selected for study. A cost survey indicated that, of the steels produced in sizable tonnages, carbon steels in the range of 0.18 to 0.23 pct C content require the most conditioning. Since this is particularly true of C1020, any im-provement of surface quality that might be effected from the study would be beneficial. Also, since the frequency of ingot cracks is exceedingly high for this grade, the steel would provide an excellent opportunity for a thorough study of the ingot-crack-ing problem. Why steels in this carbon range tend to exhibit more ingot cracks than do other steels was not considered in the investigation; the mechanism of ingot-crack formation was of paramount importance. Also, only the top-pouring practice was considered in the investigation, because this pouring procedure is used more extensively than others. In this study, ingot cracks are defined. as deep surface defects that sometimes are observed in an ingot prior to rolling but usually are observed during the initial stages of rolling on the primary mills. These defects may occur at any angle to the rolling direction but are most prominent in the transverse or nearly transverse direction. The appearance of ingot cracks on the rolled product varies with respect to their angle of formation and with the extent of rolling after their first occurrence. Ingot cracks are also termed "deep seams," "arrowheads," "irregular cracks," and "transverse cracks." Fig. 1 shows ingot cracks in a rolled bloom. This report summarizes: l—the exploratory investigation of commercial-size ingots; 2—the labor-atory investigations related to determining the source of ingot cracks and developing corrective methods; and 3—the plant evaluations of laboratory methods of decreasing ingot cracks. Exploration of lngot Cracks in Commercial Ingots Materials and Experimental Work: At the Du-quesne Works of the United States Steel Corp., five heats of killed, fine-grained C1020 steel were selected for the exploratory phase of the seam-research program. The heats were made by open-hearth practices that are considered most conducive to good surface quality. They were top-poured into 22x25 in. big-end-up hot-topped molds. One as-cast ingot and four other ingots rolled to the following cross-sectional sizes were set aside from each heat: 16x20 in.; 9 1/2x10 in.; 5x5 in.; and 2x2 in. The processing of the heats, from the time of charging in the open hearth furnaces to the end of the rolling operation on the primary mill, was observed carefully and recorded. The cast ingot and the four rolled ingots from each heat were examined for surface defects. The cast ingots were split longitudinally near the vertical center plane to expose the ingot structure beneath badly cracked regions. Also, a series of transverse sections was cut at about 1 in. intervals in a badly cracked area of one ingot. All sections were ground, polished, examined by sulphur printing and deep etching, and photographed. The rolled ingots

Jan 1, 1955

By C. S. Brooks

Several of the commonly used methods for deter-mination of effective grain densities of minerals have been evaluated for accuracy and precision, and their applicability to various types of petroleum reservoir minerals tested. Consideration was given to the effect of consolidation, swelling clay, and wettability on these grain-density determinations. Procedures with helium displacement, a modified low-pressure Boyle's law porosimeter, and liquid displacement (water, n-decane, and n-octanol) were tested. The helium-displacement procedure was used primarily as an independent reference for which the effects of fluid-solid interaction, e.g., adsorption and wettability, were negligible. The procedures with the Boyle's law porosimeter and with liquid displacement are the methods in common use. Minerals investigated included calcite, West Texas limestone core samples, California sandstone core samples, and Wyoming bentonite. The number of samples tested, while not large, was adequate to permit application of statistical methods. Grain-density measurements on calcite (Iceland spar) provided a basis of comparison for the accuracy and precision of the procedures under investigation for a material with a high degree of chemical and physical homogeneity and for which fluid-solid interactions were at a minimum. Liquid-displacement procedures (water or n-decane) provided the greatest reliability and precision for measurement of the grain densities of the limestone tested. Gas-displacement procedures (helium or Boyle's law porosimeter) provided the greatest reliability and experimental convenience, if not the greatest precision, for the measurement of the grain densities of the swell- ing clay, Wyoming bentonite, and the shah sandstones which -contained appreciable amounts of swelling, in-terstitial clays. These experiments were designed to evaluate the applicability of the grain-density procedures in common we to some of the less tractable minerals—tight limestones, shaly sandstones, and swelling clays. The results should provide a useful basis for a selection of the method most suitable for application to the various petroleum reservoir minerals encountered and especially for use in the estimation of formation porosity. INTRODUCTION These experiments were undertaken to evaluate the accuracy and precision of several commonly used methods for determination of effective grain densities of minerals, and to test their applicability to various types of petroleum reservoir minerals. Consideration was also given to the effect of consolidation, clay, and wettability on these grain-density determinations. Procedures used included measurements with helium displacement, with a modified low-pressure Boyle's law porosimeter, and with liquid displacement (water, n-decane, and n-octanol). The minerals investigated included calcite, West Texas limestone core samples, California sandstone core samples, and Wyoming bentonite. The accurate determination of the porosity of petroleum reservoir formations, in particular those of low porosity, has received much attention. Both bulk-volume and grain-volume measurements necessary in the evaluation of porosity have been examined by many investigators with the objectives of improving both the accuracy and the precision of these determinations. In this investigation statistical criteria for selection of the most reliable and suitable procedure for use with a given type of mineral are demonstrated. The grain-volume measurement procedures appear to be the most susceptible to improvement.

Jan 1, 1958

Jan 1, 1927

By J. H. Frye, C. P. Sun

A Frimary substitutional solid solution is a solution that has the same crystalline structure as the solvent metal, and in which solute atoms have replaced, solvent atoms at random on the host lattice. This replacement usually results in an increase in hardness as measured by conventional penetration tests. The factors controlling this hardness increase have been investigated in some detail for copper and silver alloys.1-5 It has been shown that at least four factors are involved: (1) concentration of solute, (2) row of the periodic table from which the solute is taken, (3) increase in lattice parameter of the solvent produced by the solute, and (4) work-hardening produced by penetration of the hardness indenter.2,4 The last factor is of the utmost importance. An investigation of the available data2,4 leads to the conclusion that the solutes that produce large hardness increases in copper or silver do so principally because they increase the rate of work-hardening. Furthermore, it is doubtful whether any solute produces appreciable hardening in the absence of plastic deformation and hence work-hardening. Thus it is clear that an understanding of the effect of solutes on rate of work-hardening is essential to an understanding of the hardness of solid solutions. This effect of solutes is also important in forming operations such as rolling or deep drawing. The presence of elements that confer rapid rates of work-hardening will increase power consumption and may well decrease the amount of deformation possible between anneals. This paper is the report of an investigation of the factors that control rates of work-hardening in copper and silver solid solutions. The silver and copper alloys considered are those in which all solutes are from the B subgroups or second short period of the periodic table. Experience with hardness, with structure of alloys, and with electrical conductivity has proved that results of a fundamental nature are most likely to be obtained if alloys are made up on the basis of the positions of the constituent elements in the periodic table. In previous work, Meyer analysis data on high-purity copper and silver solid solutions were obtained through careful measurements with fully calibrated equipment and these data were corrected to correspond to a standard grain size. From these corrected Meyer analysis data rates of work-hardening have now been calculated. Calculation of Rates as Work- HARDENING The Meyer analyses, on which this study of rates of work-hardening is based, consisted in determining impression

Jan 1, 1944

By J. H. Frye, C. P. Sun

A Frimary substitutional solid solution is a solution that has the same crystalline structure as the solvent metal, and in which solute atoms have replaced, solvent atoms at random on the host lattice. This replacement usually results in an increase in hardness as measured by conventional penetration tests. The factors controlling this hardness increase have been investigated in some detail for copper and silver alloys.1-5 It has been shown that at least four factors are involved: (1) concentration of solute, (2) row of the periodic table from which the solute is taken, (3) increase in lattice parameter of the solvent produced by the solute, and (4) work-hardening produced by penetration of the hardness indenter.2,4 The last factor is of the utmost importance. An investigation of the available data2,4 leads to the conclusion that the solutes that produce large hardness increases in copper or silver do so principally because they increase the rate of work-hardening. Furthermore, it is doubtful whether any solute produces appreciable hardening in the absence of plastic deformation and hence work-hardening. Thus it is clear that an understanding of the effect of solutes on rate of work-hardening is essential to an understanding of the hardness of solid solutions. This effect of solutes is also important in forming operations such as rolling or deep drawing. The presence of elements that confer rapid rates of work-hardening will increase power consumption and may well decrease the amount of deformation possible between anneals. This paper is the report of an investigation of the factors that control rates of work-hardening in copper and silver solid solutions. The silver and copper alloys considered are those in which all solutes are from the B subgroups or second short period of the periodic table. Experience with hardness, with structure of alloys, and with electrical conductivity has proved that results of a fundamental nature are most likely to be obtained if alloys are made up on the basis of the positions of the constituent elements in the periodic table. In previous work, Meyer analysis data on high-purity copper and silver solid solutions were obtained through careful measurements with fully calibrated equipment and these data were corrected to correspond to a standard grain size. From these corrected Meyer analysis data rates of work-hardening have now been calculated. Calculation of Rates as Work- HARDENING The Meyer analyses, on which this study of rates of work-hardening is based, consisted in determining impression

Jan 1, 1944

By M. J. Humenick, K. Garwacka

A laboratory experimental research project was conducted to evaluate the use of chlorine for the oxidative destruction of residual ammonia that may remain in ground water after in-situ uranium solution mining operations. The work tested the idea of injecting high strength calcium hypochlorite solution into the mining zone to convert ammonia to nitrogen gas as a final cleanup process for ammonia removal from the ground water system. This paper details ammonia removal efficiency as a function of chlorine dose, reactant, and product material balances, and how the concept may be used as a final ground water restoration process.

Jan 1, 1985

By P. L. Menaul, P. P. Spafford

This paper discusses the most dangerous form of corrosion encountered in condensate-well oil production, the discovery of the agent causing this corrosion and the remedial chemical treatment proved effective by field use. The injection of ammonium hydroxide, even as little as one quart per day, has proved effective in preventing gas-condensate well corrosion. The injection of "Bone oil" is applied to wells producing brines containing calcium and magnesium salts. Introduction The severe corrosion of equipment in high pressure gas condensate wells has been a problem for several years and numerous papers have been presented on the subject. The term "gas condensate" or "distillate well" is applied to a distinct variety of hydrocarbon producing well, the characteristics of these wells being high bottom-hole (formation) pressures and temperatures and high gas production. These wells usually produce about 40 gal of water per million cubic feet of gas and the gas contains from 0.1 pct to 2 pct carbon dioxide. In the operation of this type of well, the operators soon noted severe internal corrosion of the pipe carrying the production. In some instances the dl tubing has been found to be corroded to perforation in eight months. The high well head pressures of 2500 to 8000 psi makes any weakening of the well equipment by corrosion extremely hazardous. Bursting of the well equipment results in very expensive repair operations and may result in the loss of valuable production, loss of the costly well, or even loss of life. In November 1944, a gas-condensate well in a Gulf Coast field producing from 9500 ft showed a tubing leak. The well was "killed" by filling it with mud through the tubing, and then the tubing was pulled. Corrosion was found to have caused several perforations in the tubing, Fig I. While the mud was being circulated to kill the well, a high pressure jet from the corroded hole in the tubing perforated the casing and damaged the well to the extent that the cost of repairs amounted to $75,000. In November 1944, another gas-con-densate well in a Gulf Coast field producing from 11,400 ft showed tubing failure. This well had been producing an average of 2,500,000 cu ft of gas daily for two years. In the workover of this well, it was found that a hole one inch in diameter had corroded through the tubing and that corrosion had reduced the wall of the tubing to less than half the standard thickness over large areas of the interior of the tubing. It was found that corrosion had also caused two leaks in the casing. After four months spent in an attempted workover failed to make the well safe for further production, the well was plugged and abandoned at a total loss of $300,000,00.

Jan 1, 1948

By P. L. Menaul, P. P. Spafford

This paper discusses the most dangerous form of corrosion encountered in condensate-well oil production, the discovery of the agent causing this corrosion and the remedial chemical treatment proved effective by field use. The injection of ammonium hydroxide, even as little as one quart per day, has proved effective in preventing gas-condensate well corrosion. The injection of "Bone oil" is applied to wells producing brines containing calcium and magnesium salts. Introduction The severe corrosion of equipment in high pressure gas condensate wells has been a problem for several years and numerous papers have been presented on the subject. The term "gas condensate" or "distillate well" is applied to a distinct variety of hydrocarbon producing well, the characteristics of these wells being high bottom-hole (formation) pressures and temperatures and high gas production. These wells usually produce about 40 gal of water per million cubic feet of gas and the gas contains from 0.1 pct to 2 pct carbon dioxide. In the operation of this type of well, the operators soon noted severe internal corrosion of the pipe carrying the production. In some instances the dl tubing has been found to be corroded to perforation in eight months. The high well head pressures of 2500 to 8000 psi makes any weakening of the well equipment by corrosion extremely hazardous. Bursting of the well equipment results in very expensive repair operations and may result in the loss of valuable production, loss of the costly well, or even loss of life. In November 1944, a gas-condensate well in a Gulf Coast field producing from 9500 ft showed a tubing leak. The well was "killed" by filling it with mud through the tubing, and then the tubing was pulled. Corrosion was found to have caused several perforations in the tubing, Fig I. While the mud was being circulated to kill the well, a high pressure jet from the corroded hole in the tubing perforated the casing and damaged the well to the extent that the cost of repairs amounted to $75,000. In November 1944, another gas-con-densate well in a Gulf Coast field producing from 11,400 ft showed tubing failure. This well had been producing an average of 2,500,000 cu ft of gas daily for two years. In the workover of this well, it was found that a hole one inch in diameter had corroded through the tubing and that corrosion had reduced the wall of the tubing to less than half the standard thickness over large areas of the interior of the tubing. It was found that corrosion had also caused two leaks in the casing. After four months spent in an attempted workover failed to make the well safe for further production, the well was plugged and abandoned at a total loss of $300,000,00.

Jan 1, 1948

By Otto Wartenweiler

After the phenomenal development of the new mine, the United Eastern Mining Co., with Mr. Frank A. Keith as President, decided to install a reduction plant. The character of the ore, closely resembling the product of other mines in the district, did not offer any particular metallurgical problems, since these neighboring mines had been operating milling plants very successfully for several years. Thus, with the general metallurgical treatment fairly well-defined, the matter of next importance was to design and construct a plant as economically as possible, that would give the best results obtainable. The ore consists of a mixture of calcite and quartz in about equal quantities, with some decomposed andesite, while the average value of mill feed was calculated to be $20 or more in gold, no silver being present. The tonnage to be treated at the start was fixed at 200 tons, but, in view of the favorable condition of the mine, it was considered advisable to arrange facilities for increasing the capacity to 400 tons. While it is best in some cases to adopt a distinct independent unit system where future enlargement is contemplated, in this instance the plans worked out differently. Summarized, the treatment adopted consists of coarse crushing, coarse grinding, fine grinding and cyanidation. For coarse crushing the selection of the No. 6 size gyratory crusher was governed not so much by its capacity as by the size of the feed openings to receive the run-of-mine material, which was too coarse for a No. 5 crusher. TO accomplish the coarse grinding to best advantage, a careful comparison was made between the modern steel ball-mill—the last word in crushing and grinding—and one of its older, and, at that time better-established, competitors, the rolls. The following conclusion was reached: While it is possible that for the sized plant under consideration the cost of operating rolls might be a little cheaper, it is preferable to use ball-mills because a simpler arrangement is possible, and because the handling of ball-mills is preferred by the operator. A marked departure was introduced for fine grinding. Instead of the long type of tube-mill, using pebbles, a mill of similar design was selected, but of much shorter length, using small cast-steel balls as grinding medium. For cyanidation, the Dorr continuous countercurrent process was

Jan 1, 1918

By Sir Nathaniel Barnaby

We must not conceal from ourselves that, against the perils arising from perforation of the shells or hulls of ships, we are greatly worse off in these days of steel and iron than we were when our ships were built of oak, teak and pine. Apart from the greater

Jan 1, 1891

By Harry A. Roe

The power drag scrapers and the slackline cableway excavator have been called "long-range excavators." Broadly, their field of usefulness is restricted to work in which their long range of action permits them to operate economically, and which other, possibly more conventional, excavating units cannot do. Both of these machines dig or lift material and transport it to a remote dumping point. They combine these two functions in a single machine, nearly always in a single straight-line motion. The purpose of this paper is to examine the important features that distinguish the machines in this group from each other, as well as from other groups. The Machines The "power drag scraper" is a long-range excavating machine that employs a bottomless drag scraper operated back and forth between digging and dumping points by two haulage cables. The typical arrangement is that of Fig. 1. This is the "slusher" of the underground mine, as well as the "dragline scraper" of the sand and gravel industry, and other open-pit mining operations.

Jan 1, 1938

By Harry A. Roe

The power drag scrapers and the slackline cableway excavator have been called "long-range excavators." Broadly, their field of usefulness is restricted to work in which their long range of action permits them to operate economically, and which other, possibly more conventional, excavating units cannot do. Both of these machines dig or lift material and transport it to a remote dumping point. They combine these two functions in a single machine, nearly always in a single straight-line motion. The purpose of this paper is to examine the important features that distinguish the machines in this group from each other, as well as from other groups. The Machines The "power drag scraper" is a long-range excavating machine that employs a bottomless drag scraper operated back and forth between digging and dumping points by two haulage cables. The typical arrangement is that of Fig. 1. This is the "slusher" of the underground mine, as well as the "dragline scraper" of the sand and gravel industry, and other open-pit mining operations.

Jan 1, 1938

By B. H. Caudle, W. J. Bernard

Factors which influence the success or failure of a waterflood can seldom be determined in the laboratory. For this reason pilot waterfloods are initiated in a repreventative portion of the oil reservoir in question. For a pilot flood to predict quantitatively the recovery to be expected in a field-wide waterflood operation, the pilot area must behave as though it were confined (surrounded by similar areas). In this study, laboratory fluid-flow models were used to determine the simplest pilot pattern, for particular conditions of mobility ratio and initial gas saturation, that would behave as though it were confined. Pilot patterns studied ranged in complexity from a single inverted five-spot to a grouping of nine regular five-spots. Only the innermost producing well in each pattern was studied. Model results showed that the optimum number of wells in the pattern depends upon the oil-water mobility ratio and the expected oil-bank size. Unfavorable mobility ratios will, in general, require more wells in the pilot pattern than will favorable mobility ratios. Pilot patterns in reservoirs which contain a dispersed, flowable, free gas saturation will require fewer wells than for the under-saturated case. The single inverted five-spot pattern was found to be unsatisfactory for predicting behavior of fully developed waterfloods. In particular, it is possible that, in reservoirs which contain a flowable, dispersed gas phase, the oil bank will never be observed at the producers due to the large amounts of free gas which continue to be produced with the oil. INTRODUCTION One method which has been used to predict the performance of a waterflood is the pilot flood. The pilot waterflood is a flood which involves only a small cluster of the reservoir wells and is located in a small, representative portion of the reservoir. The object is that oil produced from the pilot can, in some way, be related to the oil recovery to be expected from a field-wide expansion of the waterflood. However, these field pilot waterfloods have often been unreliable in the prediction of oil recovery in a fully developed waterflood. This unreliability has also been demonstrated in several laboratory studies of pilot floods. Some of the investigators have shown that there are situations in which the pilot flood oil production is far too optimistic with respect to the oil recovery in the fully de- veloped flood. Others4-G have shown that the pilot results can also be pessimistic, especially if the pilot waterflood is initiated in an oil reservoir which has been depleted by primary recovery and is at very low pressure. The major reason for this unreliability of pilot water-floods is the migration of fluids into or out of the pilot area. By the well-known method of images, if straight lines can be drawn to represent vertical planes of symmetry in a porous medium which contains pressure sources and sinks (injectors and producers), then these lines are invariant streamlines, or lines across which there is no potential gradient, and therefore no flow. In an actual reservoir, these lines of symmetry can never be established exactly because of reservoir inhomogeneities and irregular reservoir boundaries. However, if the reservoir is relatively large and contains wells in repetitive patterns, these lines of symmetry are commonly assumed to exist for the pattern units sufficiently far removed from the reservoir boundary. Lines of symmetry for the five-spot injection pattern are shown in Fig. 1. Each five-spot unit in this figure can be considered confined with respect to flow across its boundary. In pilot floods this is not the case. The lines of symmetry for the pilot patterns investigated in this study are shown in Fig. 2. It is obvious that the fluid within these pilots is not confined and is therefore able to migrate into or out of the pilot area. Intuitively, one can see that, if more wells are added to the pilot, the innermost unit tends to behave more and more like the confined pattern. However, there is a practical limit to the number of wells which should be placed in the pilot. This limit is usually determined by economic factors. It was the purpose of this study to use laboratory fluid-flow models to determine which of the previously mentioned pilot patterns will force the innermost producing well to behave as it would in a fully developed waterflood. Since fluid migration is influenced by initial saturation conditions and the mobility ratio, these factors were included in the study. The ultimate objective of this study was to develop data which would allow the operator to choose a pilot pattern and operating conditions that will yield a production history which can be applied directly as an estimate of the performance of each production well of the fully developed waterflood. BASIS FOR THE STUDY The basic problem of field pilot floods is the migration of the reservoir fluids into or out of the pilot area. This problem has been the subject of previously reported model studies on pilot floods. These studies have been concerned mainly with the development of arbitrary "correction factors" to be applied to the simple, unconfined pilot systems such as the single five-spot. The correction factors were intended to adjust the production history of the un-