Search Documents

By J. M. Flaitz, A. S. Parks

OF the various methods of sampling gas-condensate wells, a method that secures a continuous representative sample of the well stream is desirable. Such a method, consisting of a sampling tube introduced into the well tubing, has proved satisfactory. The method is sufficiently accurate for operating and engineering problems A portable testing apparatus can be used with the sampling tube to obtain data useful in studying the economic and technical aspects of the development and operation of gas-condensate properties. Introduction The recent discovery and development of gas reserves that contain hydrocarbons that condense with reduction of temperature or Pressure, or both, to form a product known as condensate, has brought many new problems to the oil and gas industries. With further discovery of deep, high-pressure fields it is presumable that many more gas fields of this type will be added to the steadily increasing number. Such gas reserves are found either associated with oil as a gas cap or in separate formations. There seems to be no positive correlation between the physical or geological nature of the reservoir, and the chemical composition or phase characteristics of its contents. Knowledge of the chemical make-up and phase behavior of gas-condensate reserves is needed to cope with many problems. A knowledge of the chemical composition and phase characteristics of the reservoir material is necessary to properly design a gasoline or recycling plant, to estimate natural gas and condensate reserves, to enable the operator to study the economic and technical aspects of various methods of operation and development, and to carry Out the plan of operating subsurface and surface lease equipment. This information is often useful in questions of mineral ownership, proration, legal position, and taxation. It is the purpose of this paper to discuss methods used by the writers to determine the chemica1 composition and phase characteristics of the fluids produced from a condensate well. The scope of the paper includes a discussion and description of the method of sampling, the results of tests on the accuracy of the sampling method, a description of a portable testing apparatus used to examine the phase characteristics, typical results of tests on wells from several condensate fields, and some of the applications of these data to production problems. References to previous work on this subject are cited at the end of the paper. The Problem At reservoir conditions of temperature and pressure, the fluids produced from a condensate well exist in a homogeneous vaporous condition. The consequent reduction of temperature and pressure that occurs as this gas enters and flows up the well tube results in condensation of some of the hydrocarbon material to form a liquid. The relative amount of liquid condensed at any point in the flowing system

Jan 1, 1942

By J. M. Flaitz, A. S. Parks

OF the various methods of sampling gas-condensate wells, a method that secures a continuous representative sample of the well stream is desirable. Such a method, consisting of a sampling tube introduced into the well tubing, has proved satisfactory. The method is sufficiently accurate for operating and engineering problems A portable testing apparatus can be used with the sampling tube to obtain data useful in studying the economic and technical aspects of the development and operation of gas-condensate properties. Introduction The recent discovery and development of gas reserves that contain hydrocarbons that condense with reduction of temperature or Pressure, or both, to form a product known as condensate, has brought many new problems to the oil and gas industries. With further discovery of deep, high-pressure fields it is presumable that many more gas fields of this type will be added to the steadily increasing number. Such gas reserves are found either associated with oil as a gas cap or in separate formations. There seems to be no positive correlation between the physical or geological nature of the reservoir, and the chemical composition or phase characteristics of its contents. Knowledge of the chemical make-up and phase behavior of gas-condensate reserves is needed to cope with many problems. A knowledge of the chemical composition and phase characteristics of the reservoir material is necessary to properly design a gasoline or recycling plant, to estimate natural gas and condensate reserves, to enable the operator to study the economic and technical aspects of various methods of operation and development, and to carry Out the plan of operating subsurface and surface lease equipment. This information is often useful in questions of mineral ownership, proration, legal position, and taxation. It is the purpose of this paper to discuss methods used by the writers to determine the chemica1 composition and phase characteristics of the fluids produced from a condensate well. The scope of the paper includes a discussion and description of the method of sampling, the results of tests on the accuracy of the sampling method, a description of a portable testing apparatus used to examine the phase characteristics, typical results of tests on wells from several condensate fields, and some of the applications of these data to production problems. References to previous work on this subject are cited at the end of the paper. The Problem At reservoir conditions of temperature and pressure, the fluids produced from a condensate well exist in a homogeneous vaporous condition. The consequent reduction of temperature and pressure that occurs as this gas enters and flows up the well tube results in condensation of some of the hydrocarbon material to form a liquid. The relative amount of liquid condensed at any point in the flowing system

Jan 1, 1942

By AIME AIME

OUR own Institute of Metals and Iron and Steel divisions cooperated with the Iron and Steel Division of the American Society of Mechanical Engineers, the American Welding Society, and the American Society for Steel Treating in a busy week at Cleveland. The morning sessions were held at the Hotel Cleveland and the afternoon ones at the Auditorium, where the metallurgical exhibition under the auspices of the American Society for Steel Treating not only occupied the arena of the Auditorium but completely filled the huge adjacent Annex. In the intervals of sessions the members thronged the exhibits but in the evenings the local attendance was so great that if the crowds had been any larger it would have been difficult to see the exhibits. With so many firms, both producers of metals and of equipment accessory to their production and use, it would be impossible to mention them -all and unfair to single out a few, since no two individuals' judgment would coincide as to relative interest and importance. In any case an exhibit is a thing to be seen rather than described, and these were well worth seeing.

Jan 1, 1929

By Frank L. Gaddy

Falls of roof account for over 50% of the fatalities that occur in coal mines in the US. Thus, roof control is one of the more important phases of underground mining. In reality, the control of roof influences the system of mining and is a major determinant of the width and spacing of working places, operations at the mining face, ventilation control, and surface subsidence. Frequently, the control of roof is the largest single cost item. Roof control is a never-ending task, not only at the working face and throughout sections where men are working, but along haulways and air- ways that must be maintained for the life of the mine. This is because roof, even the hest of roof, slowly deteriorates, so it must be frequently examined, with corrective support applied when needed. As coal is excavated, stresses are set up in the roof because the previous equilibrium is upset, resulting in pressures that cause fractures and slight movements that are frequently hard to detect. Unless the immediate roof, in the excavated area, is given support by artificial means, it might fall or there might be a succession of falls, varying from a thin scale to several feet, depending on the nature of the top. Exceptions to this are those rare mines, or sections of mines, with hard, strong, nonweathering roof that requires no support. GENERAL CLASSIFICATION OF ROOF There are two broad types of roof as far as support is concerned: the immediate roof above the coal and the main roof. Artificial support for mining purposes is only concerned with the immediate roof as nothing except large blocks of solid coal, or massive concrete, will support the main roof. The immediate roof is generally a few feet thick but call vary from inches to 6.1 m (20 ft) or more. There are examples of where there is no imrncdiate roof as the massive main roof lies directly on the coal

Jan 1, 1981

By Carlton D. Hulin

The usual concurrence in time and space of intrusive igneous activity, favorable structural disturbance and mineralization, which is so manifest in the mineralized district necessarily indicates a close interrelationship between these events. Evaluation of available evidence leads to the recognition that an appreciable time interval exists between the emplacement of the igneous intrusive and the formation of associated ore deposits. During this interval known portions of the intrusive are completely solidified, highly differentiated magma facies are injected as dikes, and important faulting occurs, which may fracture and shatter the solidified intrusive body. The highly differentiated dike types could only have originated in some deep portion of an underlying plutonic body that had reached an advanced stage of magmatic differentiation. Appearing after these dikes, the mineralizing solutions may likewise be presumed to have originated at great depth. Certainly no source for these solutions can be found in near-by portions of the intrusive igneous body. The association of igneous intrusives and clustering ore deposits must be recognized as resulting from structural control. The emplacemerit and the subsequent solidification and cooling of the intrusive set in operation forces that are responsible for the favorable structural disturbances that control the mineralized district. The emplacement of the body of fluid magma weakens the crustal rocks to the extent that failure due to strains originally present in the rock body may occur. Faulting of any type and of any magnitude may be the result. Subsequently, owing to the change of state from fluid magma to crystalline granitic rock, volume decreases approximating 10 Per cent may Occur, with resultant shrinkage and collapse within the rock body. Following solidification, thermal contraction, induced by cooling of the rock body, causes a further volume reduction of 6 per cent. This thermal contraction, extending over a lengthy period of time, results in a succession of minor fault movements. These small fault movements, occurring progressively throughout the period of mineralization, are responsible for maintaining the permeability of the rock body, without which access of the mineralizing solutions and the formation of the ore deposits of the mineralized district would be impossible. Introduction A proper understanding of the causes that have localized our mineralized districts should be of considerable value to geologist and engineer alike. under current conditions the known ore reserves of productive mining camps are being rapidly depleted. Although ore of the future will be derived in part from deposits now known and from Ore bodies that are still to be discovered within the limits of productive mining districts, in part at least it must come from mineralized districts whose existence or importance yet remain to be recognized. The mining geologist is thus faced with two problems of paramount importance: (I) the location of new ore bodies within known mineralized areas and (2) the location of new mineralized districts within whose confines, previously unknown, valuable Ore deposits may occur. Any contribution to our knowledge concerning the causes for the localization of mineralized districts

Jan 1, 1949

By Carlton D. Hulin

The usual concurrence in time and space of intrusive igneous activity, favorable structural disturbance and mineralization, which is so manifest in the mineralized district necessarily indicates a close interrelationship between these events. Evaluation of available evidence leads to the recognition that an appreciable time interval exists between the emplacement of the igneous intrusive and the formation of associated ore deposits. During this interval known portions of the intrusive are completely solidified, highly differentiated magma facies are injected as dikes, and important faulting occurs, which may fracture and shatter the solidified intrusive body. The highly differentiated dike types could only have originated in some deep portion of an underlying plutonic body that had reached an advanced stage of magmatic differentiation. Appearing after these dikes, the mineralizing solutions may likewise be presumed to have originated at great depth. Certainly no source for these solutions can be found in near-by portions of the intrusive igneous body. The association of igneous intrusives and clustering ore deposits must be recognized as resulting from structural control. The emplacemerit and the subsequent solidification and cooling of the intrusive set in operation forces that are responsible for the favorable structural disturbances that control the mineralized district. The emplacement of the body of fluid magma weakens the crustal rocks to the extent that failure due to strains originally present in the rock body may occur. Faulting of any type and of any magnitude may be the result. Subsequently, owing to the change of state from fluid magma to crystalline granitic rock, volume decreases approximating 10 Per cent may Occur, with resultant shrinkage and collapse within the rock body. Following solidification, thermal contraction, induced by cooling of the rock body, causes a further volume reduction of 6 per cent. This thermal contraction, extending over a lengthy period of time, results in a succession of minor fault movements. These small fault movements, occurring progressively throughout the period of mineralization, are responsible for maintaining the permeability of the rock body, without which access of the mineralizing solutions and the formation of the ore deposits of the mineralized district would be impossible. Introduction A proper understanding of the causes that have localized our mineralized districts should be of considerable value to geologist and engineer alike. under current conditions the known ore reserves of productive mining camps are being rapidly depleted. Although ore of the future will be derived in part from deposits now known and from Ore bodies that are still to be discovered within the limits of productive mining districts, in part at least it must come from mineralized districts whose existence or importance yet remain to be recognized. The mining geologist is thus faced with two problems of paramount importance: (I) the location of new ore bodies within known mineralized areas and (2) the location of new mineralized districts within whose confines, previously unknown, valuable Ore deposits may occur. Any contribution to our knowledge concerning the causes for the localization of mineralized districts

Jan 1, 1949

By K. H. Coats

This paper describes an approximate technique for handling the problem of percolation of evolved gas upwards through the oil column in computer simulation of natural depletion. This technique has been incorporated into a general model for simulating three-phase flow in one, two or three dimensions. The mathematical model for perfonning these calculations is described in detail in a separate article. 1 While vertical gas percolation occurs during natural depletion in a reservoir of any configuration, it is especially pronounced in the pinnacle reel or bioherm. The reel may have an areal extent less than one section with a thickness of up to 800 It. The upward percolation of evolved gas often limits the time step in calculations as little as one day. Using this small time step, computer expense for a single 30- to 40-year simulation on even a one-dimensional basis has exceeded 92,000. The method described here for handling the percolation allows time steps of 60 days or more (depending on reservoir size and production rate), resulting in a considerable reduction in computing expense. The method also allows calculations in which secondary gas caps build up in tight zones of the oil column below the main gas cap. The validity of the method is indicated in connection with an example pinnacle reef field. Calculated results using a 2-day time step (where the method in question is not needed and not invoked) are compared with results using the method and a 60-day time step. The comparison shows good agreement. Results from one- and two-dimensional simulations of the reef are presented along with the corresponding computing times on the CDC 6600 computer. A three-dimensional simulation was also performed and the required computing time is given. INTRODUCTION A general analysis for simulating three-dimensional, three-phase flow in reservoirs has been developed. 1 In applying this model to reservoirs undergoing natural depletion, a time-step restriction was encountered due to the flow of evolved gas upwards through the oil column and toward the gas cap. A remedy for this problem has been incorporated in the analysis and is described here. The time-step restriction is encountered only in calculations which include flow in the vertical or near vertical direction. The restriction occurs to some extent in reservoirs of any geometrical configuration, but it is especially pronounced in the pinnacle reef or bioherm where the ratio of thickness to areal extent is unusually large. This paper describes the problem, a method of handling it, incorporation of the method in the three-dimensional, three-phase model, and, finally, a test of the method's validity in an application to an example pinnacle reef reservoir. THE PROBLEM During the early stages of reservoir depletion, pressure falls below bubble point in progressively lower regions of the oil column. Continuing production results in evolution of dissoived gas throughout the oil column. This gas then percolates upwards toward the top of the reservoir. If the gas encounters a sufficiently low permeability zone in its travel upward, then it can accumulate and form a secondary gas cap. If no zones are encountered which are tight enough to hold gas against the gravity forces, then the gas travels on until it reaches the top of the sand or the main gas cap. Numerical simulation of multiphase flow in reservoirs is generally performed with time steps such that the flow of a fluid into or out of a block in one time step is a fraction (considerably less than one) of the total amount of that fluid present in the block. Use of a time step where the time step's

Jan 1, 1969

By John Birkinbine

In the preparation of the paper upon " The Operation of Warwick Furnace, Pennsylvania, from August 27, 1880, to September 1,1885," presented at the Pittsburgh meeting, I purposely refrained from offering theories to explain the peculiarities of furnace operation, on the ground that it was better for those actively engaged in blast-furnace management to present records of operations, than for one more directly interested in blast-furnace engineering and construction to venture upon the sea of speculation as to causes. The manager of an iron-works naturally feels that he knows as much about his particular furnace or furnaces as any one else, and as Mr. Cook, after his close attention to and study of the Warwick furnace, was at that time unwilling to present theories, I felt a disinclination to assume more acumen than the manager.

Jan 1, 1887

By Colin Baker, G. C. Smith

Investigation of the initiation and propagation of ductile failure in OFHC copper was undertaken to determine the role of nonmetallic inclusions. The effect of inclusion initiated voids on the formation of the internal cavity and the final shear separation was studied by metallographic eranzination of strained test pieces. A strain anneal technique was used to enlarge the voids under uniaxial stress conditions to elinzinate triaxial stress effects. Measurements of void size us stress and strain were made to show the point at which void im'tiation begins and becomes an important factor in the deformation process. The work of separation of copper-cuprous oxide was determined to attempt to correlate the breakdown of the matrix inclusion interface with void initiation and propagation. The zloid shape and position relative to the tensile axis suggested an interface breakdown mechanisnz of initiation. Evidence is presented that shows a basic similarity between the central cavity propagation and the 45-deg shear portions of the failure. DUCTILE fracture has been studied by a number of workers1-lo and attention drawn to the importance of hard second phase particles in the initiation of the failure. Holes formed at the matrix-particle interface can elongate by plastic deformation and then subsequently expand sideways to link up and produce a major crack. This is usually observed first in the center of the macroscopically necked region of a test-piece where the hydrostatic stresses are at a maximum. As the crack spreads sideways towards the free surface of the specimen, well defined shear zones develop from the crack tip and the final separation is along a direction at approximately 45 deg to the stress axis. This shear failure may also be associated with voids formed adjacent to second phase particles. In this way a cup and cone type fracture is produced. The stage at which separation takes place between particles and the surrounding matrix has not been clearly identified. In addition, although researchers have dealt with anisotropy of tensile behavior" as a result of material fabrication variables, not much is known about the microstructural features of aniso-tropic behavior. In the present work evidence on these points is presented in relation to the behavior of copper containing second phase particles of cuprous oxide. I. MATERIALS AND PROCEDURES EMPLOYED The material used was +-in. diam or 2-in. sq cold-drawn OFHC copper bar which contained 0.6 pct by volume of cuprous oxide inclusions. These ranged in COLIN BAKER, Junior Member AIME, formerly at -mnF of Metallurgy, University of Cambridge, Cambridge, England, is presently Research Scientist Reynolds Metals Co., Richrnand, Va. G. C. SMITH, Member AIME, is Senior Lecturer, Department of Metallurgy, University of Cambridge. Manuscript submitted June 20, 1967. IMD size from approximately 1 to 6 p in length and 1 to 4 p in width. The shape was generally slightly ovoid. Tensile tests were made on specimens having a gage length of 2.5 cm and diameter of 0.643 cm. Metallographic examination was carried out by sectioning deformed and fractured specimens; in addition fracture surfaces were examined optically and with a scanning electron microscope. Some measurements of the work of separation between copper and cuprous oxide were made, using a sessile drop technique which was a modification of that used by Kingery and umenick." The best metallographic results were obtained by using a vibratory polisher, which minimized smearing of the surface. 11. RESULTS A) Initial Experiments. Specimens from the +-in. diam rod were annealed for 2 hr at 650°C in uacuo, at which temperature complete recrystallization occurred without any change in the form of the inclusion. They were then fractured at temperatures from -190" to 600°C. Cup and cone fractures were obtained at all temperatures from -196" to 400°C. With increase in temperature there was, however, a continuous increase in the extent of the central transverse area and a corresponding decrease in the shear portion of the fracture. Above 400°C, the fractures became intergranular. Sections of specimens tested below 400°C revealed extensive small voids which were always associated with inclusions. However, the voids only reached dimensions greater than the inclusion size in the region of the macroscopic neck, where they were many times longer. Lateral expansion was found only near the fracture surface of the test pieces. As observed by Puttick, the voids were either (a) triangular holes initiated in the direction of the tensile axis and elon-

Jan 1, 1969

By John T. Norton, V.G. Mooradian

The diffusion of metal atoms into the crystal lattice of another metal and the assumption of regular positions to form a homogeneous alloy are some of the most fundamental phenomena of structural metallurgy. The mechanism of this process has been the subject of a great deal of study from many viewpoints, but the picture is still far from complete. It is generally believed that if one metal is to diffuse into another, the first must have some solubility in the second1. This means that the solvent must be able to accommodate the stranger atoms, either on points of its own lattice or in the interstices between, without losing its own crystal-lographic identity. It is also a general observation that cold-working is a distinct aid in the diffusion process, causing it to take place with greater rapidity at the same temperature or with the same speed at a lower temperature. There is considerable doubt, however, as to the real significance of the deformation in its effect on the diffusion mechanism. Several factors associated with the cold-working may be responsible for the increased diffusion rate. The plastic deformation causes a distortion of the solvent lattice, which may be an aid in the assimulation of atoms of another kind. There are many references2 in the literature that suggest that some distortion or "loosening" of the lattice is necessary for atomic migration and that diffusion cannot take place in the undis-torted lattice. On the other hand, it may be that the cold-working causes an increase in surface of contact between the two metals through fragmentation or provides a more intimate contact that is necessary for diffusion. If it is true that lattice distortion is an important factor in diffusion, it seems as if there should be some particular relation between

Jan 1, 1935

By V. G. Mooradian, John T. Norton

The diffusion of metal atoms into the crystal lattice of another metal and the assumption of regular positions to form a homogeneous alloy are some of the most fundamental phenomena of structural metallurgy. The mechanism of this process has been the subject of a great deal of study from many viewpoints, but the picture is still far from complete. It is generally believed that if one metal is to diffuse into another, the first must have some solubility in the second1. This means that the solvent must be able to accommodate the stranger atoms, either on points of its own lattice or in the interstices between, without losing its own crystal-lographic identity. It is also a general observation that cold-working is a distinct aid in the diffusion process, causing it to take place with greater rapidity at the same temperature or with the same speed at a lower temperature. There is considerable doubt, however, as to the real significance of the deformation in its effect on the diffusion mechanism. Several factors associated with the cold-working may be responsible for the increased diffusion rate. The plastic deformation causes a distortion of the solvent lattice, which may be an aid in the assimulation of atoms of another kind. There are many references2 in the literature that suggest that some distortion or "loosening" of the lattice is necessary for atomic migration and that diffusion cannot take place in the undis-torted lattice. On the other hand, it may be that the cold-working causes an increase in surface of contact between the two metals through fragmentation or provides a more intimate contact that is necessary for diffusion. If it is true that lattice distortion is an important factor in diffusion, it seems as if there should be some particular relation between

Jan 1, 1935

By Chester R. McKee, Robert W. Terhune, Merle E. Hanson

The relationships describing the enhancement of permeability by firing explosives in boreholes have been derived and combined to yield permeability enhancement as, [ ] or the case in which the stress decays asymptotically as a power law kc and nc represent permeability and fracture density at the edge of the pulverized region near the cavity wall, f is a geometric attenuation factor, m is the dissipation due to real material effects, ko is the original permeability and rd is the scaled radius. This relationship has been compared with available measurements from the American nuclear shot "Hardhat", the French nuclear events in Hoggar granite and the chemical explosive shot in coal near Kemmerer, Wyoming. Significant correlation between this theory and the experimental measurement is observed. A comparison between single and multiple detonations shows that permeability enhancement falls off steeply near the shot; however enhancement can be considerable midway between two shots spaced 10 cavity radii apart. The degree to which enhancement, can be significant depends on material properties and fracture density. Porosity distribution from the explosive 1s the dominate parameter in permeability enhancement. Existing theories of permeability enhancement have also been reviewed.

Jan 1, 1976

By M. E. Wadsworth

The region about the south shore of Lake Superior is to geologists one of the most interesting districts of the United States, embracing as it does, in a limited area, old crystalline rocks, together with forms that are almost in their original condition of a beach sand and mud. In this region was first established the base of the geological column, the Azoic (" without life") System of Foster and Whitney, or the Archæan (" the beginning ") of Dana. Overlying this system are found the sandstones and limestones of the Paleozoic (" ancient life "), and their associated lava-flows (Algonkian ?). These systems possess a strong economic interest, owing to the stores of iron in the Azoic and of copper in the Paleozoic or Eozoic of this district, which forms one of the most important mining regions in America. The geology of this section is so difficult and complicated that, in its general discussion, perhaps no proposition can be stated concerning any portion of it to which exceptions cannot be taken. Indeed, out of the general discussion of different points comes in time the truth, and various geologists, even now, are working over this region in the endeavor to arrive at some consensus, or at least to determine upon what points they can agree, and upon what points difference of opinion will have to exist between them at present, until further evidence can be obtained. The writer will endeavor to give in a brief form that which appears to him at present to be the most correct statement of the geological structure of the region, admitting that from time to time, as more complete evidence shall be obtained, he expects to change his views in the future, as he has done in the past, if that evidence shall cause him to believe that he has been mistaken.

Jan 1, 1898

By J. E. Pollock

IN the oil-refining industry, steel comprises by far the greatest proportion of the materials used in construction work, but with an enormous number of alloy steels and nonferrous alloys available, and a greater knowledge of their properties and corrosion resistance; a substitu-tion first in the "hot spots" and then in locations of moderately severe corrosive conditions will be made as the greater expense can be justified. In new construction work, advantage is taken of the experience already gained and appropriate materials used, whether for high temperatures and pressures demanding additional strength or for corrosive conditions. The locations, however, where equipment in operation constantly requires replacement will soon become evident, as will the necessity for replacement in more resistant materials, if considerable down-time is to be avoided. In what direction and how far to go in the matter of alloys then becomes a question of the highest importance. Obviously, any replace-ment with more costly material must be. justified economically by the promise of longer life, thereby saving both material and installation costs besides the reduction of loss of production. Where the equipment is overcapacity and a regular schedule of cleaning periods is in force, the last item frequently must be ruled out and justification made on the basis of the first two only. Installation of material that will outlast the remainder of the equipment and have no recovery value must also be avoided; this is particularly important in temporary construction or in old equipment that will soon become obsolete.

Jan 1, 1935

By C. W. Wahsburne

Former studies of sedimentatry strata have been based upon the mineralogical and mechanical characters of the solid components, rather than upon the open spaces between them.

Jan 1, 1915

By F. Brons, W. C. Miller

Pressure information for use in material-balance calculations is obtained, where possible, from pressure build-up surveys in shut-in wells. Using proper extrapolation methods, static pressures are obtained which, by averaging, give the field static pressure. Often, particularly in fields with a large number of wells, only spot pressure readings are available. A graphical method is presented here which enables the determination of the corrections which must be applied to the spot readings to give an estinzate of the static pressure. Although the static pressures thus obtained are not so reliable as those from build-up surveys, they are more nearly correct than the spot readings themselves for use in material-balance calculations. INTRODUCTION The average static pressure in a bounded reservoir is determined from a number of individual-well pressure measurements. Where pressure build-up curves are available, extrapolation methods such as described in Ref. 3 may be used to determine the static pressure in the drainage area of each individual well. The possibility of using pressure build-up curves presupposes that each well being surveyed is closed in during a certain period and that, during this time, a pressure recorder is left suspended in the hole. For surveys in fields with a large number of wells, this is usually not feasible for economic and other reasons. Either a large number of pressure recorders would have to be used simultaneously or, using a limited number of recorders, the time interval needed to complete a field-wide survey would be too long. The data obtained for this incomplete coverage are insufficient to permit reliable averaging of the few calculated static pressures over the entire reservoir. In many such cases another type of pressure information is available, i.e., spot pressure readings. During this type of pressure survey all wells are closed-in simultaneously and, after a reasonable shut-in time (e.g., three days), pressure readings are taken by running the recorder in and out of each successive well. These surveys, which are less expensive, are often taken at regular intervals, say once or twice a year. In fact, such surveys are required by the state regulatory bodies in many portions of the united States. These spot readings are normally lower than the static (fully built-up) pressure due to the relatively short shut-in time. No direct means of extrapolating such a reading to the static pressure is available because no pressure build-up record is obtainable. Consequently, these data are inferior to pressure build-up information as a basis for estimating the stabilized reservoir pressure in the drainage area of a specific well. For the common case where abundant spot readings but only a few pressure build-up surveys are available, our studies suggest that it may be possible to design a program which will combine the two types of information and provide an estimate of the average reservoir pressure that is more reliable than that obtainable solely from either set of data. in time) gives a point marked p. The actual static pressure at the time the well was shut-in is marked by p.. The illustration shows that, even if a build-up curve is available and can be extrapolated, a correction

A GREAT labor, surely, is that of the coppersmith, since his every work must be hewn from the mass of copper by force of the hammer. At the beginning, middle, and, end all his works are inconvenient pieces and unpleasant to handle. If the work is done on the forge with the fire, it is done in order to refine or compose it into masses again, for drawing these out while hot with the blows of some heavy hammer, or in order to put the works in a condition that allows them to be drawn out while cold and worked. In this he puts all his labor and industry. He who works at this art often makes use of large hammers, sometimes of small ones, and sometimes of those that have a long iron head and a short handle. With these he is obliged ever to proceed in one of these activities, either extending the work lengthwise, narrowing it, or widening it. This is achieved by the manner and direction of striking and therefore it is sometimes hammered on the inside, sometimes on the outside, sometimes with the peen, and sometimes with the flat head. For instance, when he wishes to close it up he strikes it on the outside with the peen, and if he wishes to widen it he strikes it on the inside with either the flat head or the peen. In this way he proceeds to shape it with constant patience, and to make all the vessels that he works graceful. This metal, as I have told you, is soft, flexible, and tenacious under the hammer. It yields with a certain toughness, provided, however, that it is fine and without admixture of a trace of tin or other metal. That craftsman is a good master of this art who best makes every desired work

Jan 1, 1942

Jan 1, 1932

By E. M. Norris

In the summer of 1917 it was decided to fireproof the main Tramway hoisting shaft of the Anaconda Copper Mining Co. at Butte, Mont. The shaft has three hoisting compartments and one pump compartment; it is timbered with 12 by 12-in. (30.5 by 30.5-cm.) fir timber, and is 2475 ft. (754 m.) deep. Subsidence and displacement of the surrounding country rock had produced exceedingly heavy ground, and had carried the shaft out of line, in several places, by as much as 2 ft. (0.6 m.) displacement. Constant repairing and realigning of the timbers had been necessary in order to maintain clearance for the cages. The most feasible method of fireproofing, therefore, seemed to be to cover the timbers with a coat of concrete applied with the cement gun. The cement gun, which is operated by compressed air at ordinary mine pressures, feeds a mixture of sand and cement through a hose to a nozzle having a water connection. The mortar in fluid form is thus sprayed upon the prepared surface in thin layers, which can be built up to any desired thickness. The cement gun can be set up at any convenient point; satisfactory results have been obtained with the nozzle a distance of 500 ft. (152 m.) from the gun. The shaft was thoroughly overhauled and the timbers put in the best possible state of repair. Between the 1000 and the 1400 levels, much loose ground lay against the shaft timbers on the north side; this was breast-boarded back and a 30-in. (76-cm.) reinforced-concrete retaining wall was erected, leaving a space of 12 in. (30.5 cm.) outside the shaft timbers to allow for future movements of the ground. For convenience in handling men and materials, it was arranged to concrete the auxiliary hoisting-cage compartment and the pump compartment first, using the cages of the main hoist to serve the cementing crews. The auxiliary cage was then available while the remainder of the shaft was being concreted. A tight partition of 2-in. (5.08-cm.) plank was erected between the auxiliary and the adjoining hoisting compartments, for better protection of men riding on the cages. The application of concrete made this

Jan 1, 1920

By Leonard C. Grimshaw

Diffusion of carbon from gases into iron has been the object of much research, because of its long recognized importance in carburizing processes, but the direct diffusion of carbon from steel into iron has received relatively little attention. Because of the increasing use of clad metals in industry, direct diffusion from steel into iron is becoming of practical importance. Therefore, the object of this investigation was to study the diffusion of carbon from several different kinds of steel directly into relatively pure iron, realizing that elements in the steels other than carbon might influence the rate of carbon diffusion. The previous work on diffusion of carbon into iron has been considerable, and includes many reports in foreign languages. This work has recently been well reviewed by Mehll and Krynitsky12 and the reader is referred to their excellent bibliographies. Methods of Study There are two main methods by which the direct diffusion of carbon from steel into iron may be studied. In one method, steel is first decar-burized in part, and diffusion of carbon then allowed to take place from the steel into the decarburized steel. This method is open to two serious objections: (1) the decarburized steel is not iron, but contains elements such as manganese, silicon, chromium or tungsten, which may be an essential part of the steel under study, and which may seriously influence the diffusion of carbon into the decarburized area; (2) there is from the start of diffusion an unknown carbon-concentration gradient between the steel and the decarburized area. Another method, which possesses neither of these disadvantages, is to study diffusion from steel into a thick plating of electrolytic iron. Herc the chief difficulty is to secure an electrolytic deposit of iron upon steel without introducing an oxide film at the interface that will interfere with diffusion. The author is able to deposit iron upon any kind of steel without introducing an oxide film at the interface, so that diffusion of elements from the steel into the iron is free to proceed unhindered.

Jan 1, 1938