Search Documents

By Frank Alfred Fahrenwald

Discussion of the paper of FRANK ALFRED FAHRENWALD, presented at the New York meeting, February, 1916, and printed in Bulletin No. 109, January, 1916, pp. 103 to 149. F. A. FAHRENWALD, Cleveland, Ohio (communication to the Secretary*).-Since the publication of my paper in the January Bulletin, (which was largely a metallographic treatise), I have been questioned regarding two points referred to therein. One of these is that which deals with the application I have made, p. 119, of the equation for melting pressures which correspond with different working temperatures. The other refers to the statement, p. 137, that "Prolonged heating at relatively low temperatures gave fewer and larger crystals and crystals of different sizes, while a flashing at higher temperatures gave a very fine and uniform crystalline structure, which was much' to be preferred." Especial emphasis was not placed upon either of these two factors, for each seemed perfectly logical and obvious. As they do not seem to be self-explanatory, I will supplement with those portions of my notes which were purposely omitted from the manuscript submitted for publication. A few practical illustrations may serve as evidence in support of the first of these, but it must be understood that in this work the "amorphous theory" is considered as being sound, and that it is assumed that metals allow of distortion, without fracture, by virtue of the formation of slip surfaces, accompanied by the transformation of crystalline material to the, amorphous phase. Effect of Pressure.-In all forging, rolling, and drawing operations, it is known that specimens of small cross-section may be worked at a lower temperature than can be used for the same material in much greater mass and sectional area. In -the larger pieces the maximum pressure is brought to bear upon the material near the surface, so that the interior is not subjected to great pressure, but to, a stress more nearly tensile, or shearing, so only the surface is subjected to the critical melting pressure. In the case of wires which draw hollow, the center is subjected to practically a tensile stress which breaks it, while the surface skin draws perfectly, due to the enormous "flowing" pressure exerted upon it by the surface of the draw-plate.

Jan 5, 1916

F. W. Matthiessen, who, with E. C. Hegeler, of La Salle, was one of the creators of the zinc industry in the-United States, was born in Altona, Schleswig-Holstein, Germany, Mar. 5, 1835. He was one of a family of remarkable brothers, two of whom were long absociated in this country with the sugar and glucose industry. Mr. Matthiessen was educated at Freiberg, and came to this country in 1857 with Mr. E. C. Hegeler, after having, in company with that gentleman, visited the mining districts of Germany, Belgium, and England. They first went to Friedensville, near Bethlehem, Lehigh County, Penn., wherc attempts had already been made to produce zinc from the ore deposits found in that place. The ore was a he silicate but all attempts to extract zinc from it had failed. Mr. Matthiessen and Mr. Hegclcr were successful, but declined to invest their money in the zinc industry at Bethlehem because 01 certain local conditions. Hearing of the discovery of zinc -ore in the West, they visited both Wisconsin and Missouri and thought of settling in the coal region of East St. Louis. Finally La Salle, as being near to the Wisconsin fields and having much coal, was selected ae the site of the new smelting company, and on Dec. 24, 1858, the first shovelful of dirt was turned for the buildings of the new industry. The Civil War at first interfered with the manufacture of zinc, but afterward a lively demand for the metal arose and the future success of the institution was established. A large rolling mill was added in 1866, and in 1881 the manufacture of sulfuric acid as a byproduct was begun. Mr. Matthiessen also developed the Western Clock hlanufacturing Co. of La Salle, which manufactures the Big Ben alarm clock, from a small plant having 25 men to the present large institution which employs some 2000 workers. Mr. Matthiessen's affiliations with other metal industriefi have been numerous. But the contributions of the great zinc manufacturer to the causes of philanthropy and education have made his name known throughout the country, beyond industrial circles. He has given to the city of La Salle probably a sum total of $500,000 in various benefactions. Among the objects of his philanthropy were the La Salle-Peru Township High School, which he has made a model institution of secondary education for the entire United States; also the Tri-City Hygienic Institute of La Salle, Peru, and Oglesby, Ill., which he endowed for $200,000 This Hygienic Institute, which is unique in the United States, has a traincd staff of health officers, bacteriological laboratory, medical library, infant welfare station, milk station, free dental clinic, school nurse, and isolation hospital. Mr. Matthiessen was elected mayor of the City of La Salle three times and gave generously to the municipality of which he was the head. He also saved for the people of Illinois one of the great scenic districts of the state, Deer Park, with its cafions and natural beauties, which he con-verted into a model scenic resort, and the proceeds of which he gave to the charities of the Tri-Cities in which he lived. He died on Feb. 11, 1918.

Jan 1, 1920

By A. G. Guy

Zinc vapor from a reservoir of liquid zinc maintained at lower temperatures was diffused into sets of copper-zinc alloys at 759° and 870° C and into sets of silver-zinc alloys at 650° and 700° C. Each set of ,four copper-zinc alloys consisted of pure copper and 90/10, 80/20, and 70/30 brass. Similarly the set of silver-base alloys consisted of specimens containing 0, 7, 15, and 20 pct Zn. Natural markers at the initial surfaces of the specimens ware "trapped" under a thin electroplate and their depth of burying was measured after diffusion. The ratio of diffusivities of the two components determined from these data and the chemical diffusion coefficient calculated by the Matano method agreed with previously reported results. The line of markers was irregular and was often discontinuous when a grain boundary was crossed. TECHNIQUES involving the vapor phase have been widely employed in studying diffusion phenomena in metals. Many investigators have evaporated the more volatile component from an alloy, but it is generally believed that the porosity created under these conditions interferes with adequate interpretation of the experimental results. The extensive work of Gertsriken6 has been criticized on this score. Accary1 found that the diffusion coefficient for de-zincification of brass is larger by a factor of five than that for zincification, although he attributed the difference to a higher vacancy concentration under conditions of dezincification. Balluffi and siegle2 thoroughly investigated the technique of adding a more volatile component to a less volatile base metal as a means for studying diffusion. They verified that no porosity forms in a brass under these conditions and that the diffusivities of the two components can be determined from observations of the motion of markers originally placed on the surface of the specimen. The mathematical analysis that they developed for treating the experimental data was modified in a later note, but essentially it involved using the graphical Boltzmann-Matano method that is customarily applied to solid-solid diffusion couples. The experimental method used in the present research was similar to that employed by Balluffi and Siegle except for two modifications. Balluffi and Siegle used alloy chips as the source of metal vapor. This procedure has the disadvantage that the concentration of solute at the surface of the specimen changes during the diffusion experiment as the alloy content of the chips is gradually decreased. This disadvantage was overcome by employing liquid zinc as the source of zinc vapor in a manner similar to that described by Herasymenko.9 There was then no limitation on the amount of solute usefully available, and several relatively large specimens could be diffused in a given experiment. The second modification was the use of natural markers on the surface of the specimen rather than larger, artificial markers, such as the alumina powder employed by Balluffi and Siegle. It was expected that the fine, natural markers would permit more precise measurement of the buried interface as in the case of ordinary sandwich specimens.10 EXPERIMENTAL The experiments were designed so that zinc from the vapor phase would maintain a constant zinc content at the surface of pure copper (or silver) and

Jan 1, 1960

By Chas. A. Dobbel

The Chief Consolidated properties are situated in the Tintic mining district of Utah, being included in Juab and Utah Counties, about 70 miles south of Salt Lake City. The drilling referred to in this paper has been carried on in the Chief Consolidated No. Pmine, the Gemini mine, and the Eureka Hill mine at Eureka, the Grand Central mine, above Mammoth, and the Apex Standard mine just south of Dividend. The occurrence of ore through the district is typically in lenses on bedding or breaks, and in connecting pipes, without accurate geometrical trend so that the ratio between the total length of development in drifts and crosscuts to the square feet of ore exposed is very high. A section of one of the western channels (Fig. 1) through the Tintic district, shows, roughly, the irregularities calling for excessive development work, so typical of the Tintic mines. This irregular trend of the ore constantly calls for excessive cutting up of the whole area for offshoots and the connecting links always present. In the planning of prospecting and development, no regular system may be laid out without overlooking some orebodies or segments of orebodies. It was with these facts in mind that Cecil Fitch, the general manager of the Chief Consolidated Mining Co., decided that some method of drilling was the more feasible way of successfully cutting up and bringing about the discovery of ore believed to exist; yet this drilling had to compete with a great margin of cost over crosscutting, as a crosscut in the Tintic district, even though barren, brings out geologic facts that, in many cases, are worth the price of the working itself. Diamond drills met with the success that might be expected in a district that has a reputation for the Gear and loss of diamonds; after 6 or 8 months, this method was discarded on account of the high costs. Simultaneously, a small churn drill outfit was set up underground but a few shifts proved its inapplicability. At the same time, the ordinary hammer drill was used to drive prospect holes with jointed steel. Just what equipment to develop for this work with the hammer drill involved much experimenting, as nothing was found in the literature

Jan 1, 1925

Joseph Esrey Johnson, Jr., had already achieved rare distinction as an able metallurgist, clear thinker, brilliant author, and wise consulting engineer to bankers and operators; he had achieved the essentials of a great career when dcath cut short his activities on Apr. 4, 1919, in the forty-ninth year of his age. He belonged to a family of iron blast-furnace men and mine managers. His father, Major J. E. Johnson, after serving with distinction in the Army of the North, identified himself with the iron mines and blast furnace at Longdale, Va., with which he was connected during almost his entire business life. It is significant, that, during those troublous times of reconstruction in the South, he enjoyed always the affection and respect of his neighbors and associates alike. From him his son obtained not only a thorough training in blast-furnace practice and iron mining, but great personal courage and force of character. His mother, who survives both her husband and sons, possesses rare intellectuality, humor and a tenderness and human sympathy which those who were privileged to know well J. E. Johnson, Jr., recognized beneath his exterior of aggressiveness and will power. In a recently published analysis of the qualities which characterize the world's great men, three traits stand out preeminently; viz., independence, courage, and intellectuality. Each of these characteristics J. E. Johnson, Jr., possessed in extraordinary degree. His early education was obtained under a private tutor at Longdale, and this circumstance probably enhanced a natural tendency to independence of character and individuality which, however, under the control of his unusual power of straight thinking and clear analysis never allowed him to go far astray. It has been said of him that if once he set his mind to a problem, however knotty, he scored a bull's-eye before the subject was dropped. His manner of attacking a subject involved first mastering the details of the available knowledge; then, putting this acquired information to one side, with an untrammeled mind blazing out a path of his own, so clear, so well-defined, and expressed in such simple terms that he illuminated the whole subject without distorting the original data or discussion. His two books, "Blast-furnace Construction in America" and "The Principles, Operation, and Products of the Blast Furnace, "on the iron blast furnace together form the most comprehensive, the most enlightening, and the most useful treatise on the subject ever produced in any language. But his ability did not end with the mastery and elucidation of principles enunciated by his predecessors; his own

Jan 1, 1920

By E. S. Leaver

The authors of the paper above mentioned have sent the following statement to correct erroneous com-ments and implications in their article with the re-quest that it be published: "In the above mentioned article the reference to Bendelari jigs is used in the generic sense as applying to the mechanically driven diaphragm jigs. No attempt was made to dif-ferentiate between the various machines as installed on different dredges. The Natomas Company use a jig of their own manufacture. The Yuba Company installed the Placer jig as manufactured by the Pan American Engineer-ing Company. "The Pan American Engineering Company also manufactures the Crangle jig under their own name. This is a diaphragm jig in which the pulsations are produced by intermittent flow of water through the patent Crangle Valve and it has no driving mechanism."

Jan 1, 1937

By S. H. McFarlane, K. H. Zaininger, G. W. Cullen, C. C. Wang, G. E. Gottlieb

Heteroepitaxy of silicon on stoichiometric spinel has been studied. Both boron-doped (p-type) and arsenic-doped (n-type) single-crystal silicon films have been grown by the pyrolysis of silane on sioichiometric spinel (MgAl2O4) substrates prepared by a flux technique. The spinel crystals are free from strain and subgrains, and exhibit no thermal instability at temperatures employed for silicon deposition. The growth parameters of epitaxial silicon have been studied. Effects of substrate orientation, surface preparation, and growth conditions on the silicon Properties have been determined. The silicon-spinel composite was characterized by X-ray diffraction, electron diffraction, electron microscopy, and optical techniques. Information on epitaxial orientation relationship, defect structures and film-substrate interface has been obtained. A parallel orientation relationship was found between silicon and spinel. The silicon films exhibit no subgrain structures. However, growth pyramids, microtwins, stacking faults, and dislocations are the prevalent defects. The deformation of epitaxial silicon was measured by an X-ray technique. It was found that the epitaxial silicon is strained under compres-sive stress due to the thermal expansion difference between the film and substrate. The stress was estimated using the classical plate theory and beam equation. Electrical properties of the epitaxial silicon have been measured, including resistivity, carrier concentration, and Hall mobility. MIS and vertical through diffused junction structures have been fabricated wing silicon-spinel composite. Information on MIS characteristics, minority carrier life time, and junction properties has been obtained. THE achievement of single-crystal growth of large area silicon semiconductor films on oxide insulating substrates is of technical importance to many solid state electronic devices. The semiconductor-insulator composite structure is also of scientific interest because the heteroepitaxy is determined by the spatial relationship between the atomic arrangement in the substrate and that of the atoms in the appropriate crystallographic plane of silicon. The degree of crystalline perfection of the silicon deposits depends also on the physical condition of substrate surface. Epitaxial growth of silicon on commercial flame fusion Al-rich spinel (MgO:3.3A12O3) has been reported by several investigators.'-4 The lattice of spinel of this composition is distorted. The material cracks and exsolves the excess alumina in the lattice at temperatures (-1200°C) used in fabricating silicon devices. Stoichiometric MgA12O4 spinel exhibits neither lattice distortion nor thermal instability. Results are given on the epitaxial growth and characterization of silicon on stoichiometric spinel. EXPERIMENTAL Fabrication of Silicon-Spinel Composite Structures. The MgA12O4 spinel substrate wafers were prepared from bulk single crystals grown at about 1200°C by a flux technique5 using a PbF2 flux. The crystals are free from strain and subgrains, and exhibit a typical dislocation density of less than 50 lines per sq cm. The crystals are thermally stable without cracking and exsolution of alumina to at least 1500°C. The spinel crystals were oriented for cutting by the Laue X-ray back-reflection method.6 Substrate wafers (about 25 mil thick) of (Ill), (loo), and (110) orientations have been obtained bu cutting the X-ray oriented crystals using a standard type diamond wheel. An accuracy of better than 1/2 deg is maintained throughout the operation. The spinel substrate wafers were mechanically lapped and polished to produce the flat and smooth surface which is required for silicon epitaxy. Lapping was carried out with about 30-µ boron carbide abrasives to obtain a flat coplanar surface. The lapped surface was further polished using successively finer grades of alumina, ending with the 0.3-µ grade. After polishing the wafers generally have a flatness of ±0.4 µ per cm, as revealed by interferometry. Fig. 1 shows (111) oriented MgA12O4 spinel wafers of various shapes.

Jan 1, 1970

MINING ENGINEERING presents the annual membership report of the Society of Mining Engineers; see page 109.

Jan 7, 1963

By T. Egleston

THE ores of mercury of North California are composed of metallic mercury and cinnabar. They are found in serpentine, and are very often associated with chalcedony, in masses more or less irregular, often concentrated enough, however, to furnish ores yielding from three to ten per cent., and sometimes richer. This deposit makes its appearance in Vallejo where it has been worked. North of here the mines are more developed. Most of the quicksilver mines, how¬ever, are situated in Sonoma and Napa Counties. On its outcrop the serpentine rocks have become decomposed, and have often been washed away to a considerable depth, so that in many cases in their neighborhood, what is apparently nothing but ordinary dirt, will frequently contain from two to three per cent. of metallic mercury, with but a trace of cinnabar, in which case, as at the Sonoma mine, it is made up into adobes and distilled. Such material does not require to be mixed with dirt to be made into adobes. Very often, also, the outcrop of the rock, where it is not decomposed, is filled with metallic mercury, so that by striking a pick into it, as at the Rattle-snake mine, a pound or more of mercury at a time will sometimes spurt out. Such rock as this is found in several localities in every stage of impregnation, and usually makes very rich ore. There is generally, however, very little of it, and it is found only in the first workings ; the ore in depth is always cinnabar. At the Rattlesnake mine near Pine Flat, where large quantities of metallic mercury are found, the rock contains so much petroleum that it has been necessary to make special arrangements to burn the carbides of hydrogen, since the distillation of the petroleum causes an extra quantity of poor soot to be formed in the condensation-chambers. At the Geysers the ore is associated with large quantities of sulphur and gypsum, so that in a hand specimen there is often more sulphur than cinnabar, which is a serious impediment to working, especially for the modern style of furnace with iron condensers, and causes so much soot to be formed that it has been known to penetrate as far as the blower, and to so completely clog it as to prevent its revolution. The ore coming from the mine is more or less hand-picked. In one or two cases attempts have been made to treat the poorest, and especially the very fine ores, mechanically as at the California works.

Jan 1, 1875

By Thomas Egleston

The ores of mercury of North California are composed of metallic mercury and cinnabar. They are found in serpentine, and are very often associated with chalcedony, in masses more or less irregular, often concentrated enough, however, to furnish ores yielding from three to ten per cent., and sometimes richer. This deposit makes its appearance in Vallejo where it has been worked. North of here the mines are more developed. Most of the quicksilver mines, however, are situated in Sonoma and Napa Counties. On its outcrop the serpentine rocks have become decomposed, and have often been washed away to a considerable depth, so that in many cases in their neighborhood, what is apparently nothing but ordinary dirt, will frequently contain from two to three per cent. of metallic mercury, with but a trace of cinnabar, in which case, as at the Sonoma mine, it is made up into adobes and distilled. Such material does not require to be mixed with dirt to be made into adobes. Very often, also, the outcrop of the rock, where it is not decomposed, is filled with metallic mercury, so that by striking a pick into it, as at the Rattlesnake mine, a pound or more of mercury at a time will sometimes spurt out. Such rock as this is found in several localities in every stage of impregnation, and usually makes very rich ore. There is generally, however, very little of it, and it is found only in the first workings; the ore in depth is always cinnabar. At the Rattlesnake mine near Pine Flat, where large quantities of metallic mercury are found, the rock contains so much petroleum that it has been necessary to make special arrangements to burn the carbides of hydrogen, since the distillation of the petroleum causes an extra quantity of poor soot to be formed in the condensation-chambers. At the Geysers the ore is associated with large quantities of sulphur and gypsum, so that in a hand specimen there is often more sulphur than cinnabar, which is a serious impediment to working, especially for the modern style of furnace with iron condensers, and causes so much soot to be formed that it has been known to penetrate as far as the blower, and to so completely clog it as to prevent its revolution. The ore coming from the mine is more or less hand-picked. In one or two cases attempts have been made to treat the poorest, and especially the very fine ores, mechanically as at the California works.

By R. D. Burlingame, T. L. Joseph, Gust Bitsianes

DESPITE almost fifty years of commercial practice, the sintering of iron ore has received little fundamental study. Much of the theoretical work1-'has dealt with the constitution of sinter produced under widely varying conditions. While these studies have broadened our knowledge of the changes that occur in the sintering zone and in the freshly formed sinter during the early stages of cooling, they provide little insight into the changes that precede the formation of sinter. These preliminary changes merit study as a part of the overall process. Hessle. working with beds of Swedish magnetite concentrates, was one of the first investigators to study the sintering process in its entirety. On the basis of temperatures observed at various levels of the bed during sintering, he postulated a number of distinct reaction zones to account for the chemical changes leading to the formation of sinter. A more direct method of attack is that of arresting the sintering zone after it has progressed part way through the bed. A study of a vertical cross section through such a quenched bed provides direct information on the changes taking place at various levels. This method was used by McBriar et al.' to show that several well-defined zones of chemical change existed within beds that were typical of British sintering practice. The same general method of attack was developed independently in the present investigation to study partially sintered beds typical of American practice. Experimental Sintering Equipment The sintering operation was carried out on an experimental scale with the equipment shown in Fig. 1. The refractory-walled sintering chamber A was 11 in. deep and averaged 9 in. in diameter. Air was introduced through a tapered flow section B, which contained the orifice C for accurate metering of the incoming air. This section was located directly above the square ignition housing D, which in turn rested upon the sintering chamber A. The bed was ignited with burner E. The required suction for the operation was furnished by a fan F, which had an air capacity of 500 cfm (stp). Hot exhaust gases from the sintering chamber were cleaned in the dustcatcher G before entering the exhaust fan. In the study of partially sintered beds, it was essential to find some technique for removing the entire charge from the sintering pot without disarranging the unsintered bottom portion. This problem was finally solved by sintering the charge in a removable basket, which snugly fitted the sintering chamber. This basket was constructed of two thicknesses of window screen and was lined with a 3/16-in. layer of asbestos paper. The bottom of the basket consisted of two thicknesses of wire screen, which were fastened to the basket wall. For high fuel mixtures, additional insulation was provided by a somewhat thicker layer of asbestos cement. Preparation of Partially Sintered Mixtures The moist feed was carefully placed in the sintering basket, to prevent segregation of the particles, which varied widely in size and composition. A thermocouple was placed in the center of the basket with the hot junction halfway down, and the mixture was evenly distributed around it. During ignition and throughout the sintering of the upper half of the bed, the hot junction temperature increased very little. When the sintering zone reached the halfway point, as indicated by the sudden increase in the hot junction temperature, the charge was quenched. During quenching the suction was turned off and the orifice was tightly stoppered to prevent further influx of air. At the same time, nitrogen was admitted to the sintering chamber through the orifice tap. As soon as the nitrogen had displaced the air and products of combustion, the charge was removed from the sintering pot for immediate dissection. It is impossible to preserve the exact zone structure of the bed at the instant that combustion is arrested unless the downward transmission of heat is also immediately stopped. Fortunately, heat transfer is very slow in beds containing a stationary fluid, especially if the particle size is small. It follows that the minimum quantity of nitrogen should be used to displace the air and that static conditions be established as soon as possible. A very steep temperature gradient across the combustion zone for some time after the quench was evidence of in-

Jan 1, 1957

By W. L. Freyberger, R. B. Booth

Froth flotation is a chemically induced method for beneficiating or up- grading an ore, which utilizes a layer or column of froth as a separating medium to segregate and remove the valuable minerals from the worthless gangue components of a finely ground ore suspended in water. The object of this chapter is to discuss the theoretical aspects of froth formation, the various frothing agents employed in flotation, and the effect of chemical structure on froth formation, and to correlate these factors with flotation technology. The flotation method of separation is conducted in three main steps: 1) selective chemical modification of the surface of specific mineral particles to effect floatability or nonfloatability; 2) contact between air bubbles and mineral particles, the selective adherence of floatable minerals to these bubbles, and the rejection of nonfloatable minerals; and 3) separation of the floatable minerals from the nonfloatable minerals. As indicated above, these three operations are achieved by the use of chemicals. Frothers play their most important role in the second and third steps by influencing particle- bubble contact and by affecting the degree of separation obtained in the froth column. Frothers, as defined by flotation operators, are compounds that are used specifically for the purpose of creating a froth in a flotation separation. How- ever, some collectors produce froths that are adequate for some flotation operations. Although this chapter is chiefly concerned with the specific frothers used in flotation, some discussion of frothing collectors is included. Otherwise, collectors (or promoters) and modifiersare not discussed at length; for information on these types of flotation chemicals, the reader is referred to other sections of this book or to other sources.l HISTORICAL DEVELOPMENT OF FROTHING AGENTS Historically, there are two distinct phases in the development of frothing agents and other flotation chemicals: 1) 1860 to 1920-oil flotation, and 1921 to date-chemical flotati0n.2~3 Early in the first period, large quantities of fatty and oily materials, up to 10 to 20% of the weight of the ore, were used as a means of separating the sulfide and oxide components from the gangue minerals in ore pulps. Later, various gases replaced these large quantities of oil as a buoyant and separating medium, decreasing oil requirements to less than 1% of the weight of the ore. With this reduction in oil

Jan 1, 1962

By C. C. Wright, T. S. Spicer

A characteristic property of bituminous coal is that upon being heated the coal becomes plastic, evolves volatile gases, and finally solidifies into coke. This fundamental characteristic is of utmost importance and is utilized in the production of the high-temperature coke upon which the steel industry is so dependent; but from the standpoint of operation in the domestic underfeed stoker this coking tendency seriously interferes with efficient combustion. When the coke formed has too strong a structure, certain difficulties result, such as low rate of burning, slow response to heat demand, and, in extreme cases, extinction of fire. The plastic mass prevents uniform distribution of air through the fuel bed and, with strongly coking coals, large dense pieces of coke are produced which have much less reacting surface than was possessed by the original coal. In both ignition and combustion of solid fuels, the extent of the reacting surface is an accelerating factor. Poor combustion permits a surplus of fuel to accumulate in the furnace because the rate of feed and the rate of combustion are not in equilibrium, and this produces an unbalanced condition detrimental to continued automatic service. In order to bum strongly coking coals satisfactorily in a conventional stoker during the three requisite types of operation—continuous, intermittent and hold-fire, frequent attention is necessary. Domestic stokers are defined by the industry as residential stoker heaters that burn 60 lb. of coal or less per hour. With a few exceptions, these units employ the underfeed principle of combustion in which both air and coal move in the same direction up and through the fuel bed. Domestic combustion equipment has difficulty in meeting the problems presented by the several variations in ash and volatile matter, in ash-clinkering tendencies, in coking properties, and in the particle size of bituminous coals. The work of Bituminous Coal Research Inc. at Battelle Memorial Institute has shown that, of these, coking characteristics and the clinkering tendencies have the greatest effect upon the operation of the conventional clinkering type of stoker. Typical coke formations in a clinkering type of underfeed domestic stoker are illustratcd in Fig. I, which shows (A) the ideal fuel bed obtained with a noncoking or free-burning coal; (B) the type of fuel bed formed with a coal that produces a weak coke; and (C) the type of fuel bed obtained with a strongly coking coal. C is characteristic of the fuel bed developed when the average Pennsylvania bituminous coal is burned in an underfeed stoker of conventional type. It is apparent from these pictures that the formation of coke trees will seriously interfere with the efficient automatic combustion of Pennsylvania bituminous coals.

Jan 1, 1942

By T. S. Spicer, C. C. Wright

A characteristic property of bituminous coal is that upon being heated the coal becomes plastic, evolves volatile gases, and finally solidifies into coke. This fundamental characteristic is of utmost importance and is utilized in the production of the high-temperature coke upon which the steel industry is so dependent; but from the standpoint of operation in the domestic underfeed stoker this coking tendency seriously interferes with efficient combustion. When the coke formed has too strong a structure, certain difficulties result, such as low rate of burning, slow response to heat demand, and, in extreme cases, extinction of fire. The plastic mass prevents uniform distribution of air through the fuel bed and, with strongly coking coals, large dense pieces of coke are produced which have much less reacting surface than was possessed by the original coal. In both ignition and combustion of solid fuels, the extent of the reacting surface is an accelerating factor. Poor combustion permits a surplus of fuel to accumulate in the furnace because the rate of feed and the rate of combustion are not in equilibrium, and this produces an unbalanced condition detrimental to continued automatic service. In order to bum strongly coking coals satisfactorily in a conventional stoker during the three requisite types of operation—continuous, intermittent and hold-fire, frequent attention is necessary. Domestic stokers are defined by the industry as residential stoker heaters that burn 60 lb. of coal or less per hour. With a few exceptions, these units employ the underfeed principle of combustion in which both air and coal move in the same direction up and through the fuel bed. Domestic combustion equipment has difficulty in meeting the problems presented by the several variations in ash and volatile matter, in ash-clinkering tendencies, in coking properties, and in the particle size of bituminous coals. The work of Bituminous Coal Research Inc. at Battelle Memorial Institute has shown that, of these, coking characteristics and the clinkering tendencies have the greatest effect upon the operation of the conventional clinkering type of stoker. Typical coke formations in a clinkering type of underfeed domestic stoker are illustratcd in Fig. I, which shows (A) the ideal fuel bed obtained with a noncoking or free-burning coal; (B) the type of fuel bed formed with a coal that produces a weak coke; and (C) the type of fuel bed obtained with a strongly coking coal. C is characteristic of the fuel bed developed when the average Pennsylvania bituminous coal is burned in an underfeed stoker of conventional type. It is apparent from these pictures that the formation of coke trees will seriously interfere with the efficient automatic combustion of Pennsylvania bituminous coals.

Jan 1, 1942

By R. W. Raymond

It is impracticable to prepare for the present number of the Bi-Monthly Bulletin a detailed account of the memorable Joint Meeting of the Iron and Steel Institute and our Institute, held in London, the last week in July, and of the, innumerable festivities, entertainments and excursions which accompanied and followed it, in England, Scotland, Wales and Germany. This preliminary sketch, from which all " useful particulars "' have been carefully omitted, is published unofficially, as a convenient answer to the manifold inquiries of members who did not go, and who are now trying to alleviate their unavailing regret by indulging their curiosity. Perhaps they secretly hope to hear that they did not lose so very much, after all-that the affair was not all that could have been desired or dreamed; that there were serious drawbacks, shortcomings and disappointments; and that it is just as well to have stayed it home, and now to hear about it. Let them lay no such flattering unction to their souls. The month they have missed would have been the time of their lives. They will never, never know how good a time it was, or adequately repent of their folly, if they could have gone with us, and voluntarily did not go of course, those who would but could not, have our immeasurable pity, without blame. I shall present here no consecutive and minute story, but only a series of general paragraphs concerning different aspects and stages of our experience. THE WEATHER. The proverbial good fortune of the Institute attended its visiting members and guests at every stage of the late London meeting and the numerous excursions which accompanied or followed it. Even the process of crossing the Atlantic was made delightful by smooth seas, through which the great modern transatlantic liners made their way without disagreeable

Sep 1, 1906

By J. Trevor Eyton

This paper addresses some of the financial risk hedging mechanisms available to a corporation contemplating entering the mining business at a significant level of investment. The approach which I have adopted is that of a case study relating to the risk hedging aspects of Brascan Limited's acquisition of 46% of Noranda Inc., formerly Noranda Mines Limited, followed by some remarks on options open to mining companies for reducing financial risks. To appreciate the rationale for Brascan committing over (Can.) $800 million to the natural resource sector, some knowledge of Brascan's parent company, Edper Investments Ltd., is required at the outset. Edper Investments, prior to acquiring a 48% interest in Brascan, controlled Trizec Corporation, one of the world's largest property companies. Edper also was involved in the financial services sector through Continental Bank of Canada and Hees International Corporation. For some considerable time prior to Edper's investment in Brascan, Edper felt a need to provide a better balance to its portfolio of property and financial services. Brascan was rich in cash, relatively unleveraged, and with important existing holdings in natural resources and consumer products. The acquisition of a controlling interest in Brascan provided an opportunity to balance Edper's portfolio of property and financial services with world class acquisitions in natural resources, supplemented by consumer products and financial services. The end result of Brascan's activities over the last few years is illustrated by the following analysis of the book value of Brascan's assets at the end of December 1983. [Can.$% Millions _ Natural Resources81748 Consumer Products 654 38 Financial Services 157 9 Other Operations895$1,717100% ] Source: Brascan 1983 Annual Report. The large emphasis on natural resources came about from the fact that for Canadians operating mainly in Canada, natural resources were attractive. We were impressed by Canada's position in the world natural resource industry as illustrated by some of the following statistics: [CommodityCanadian Estimated Production In 1983 As % of World Total Newsprint 30 Potash 21 Uranium 18 Molybdenum 17 Zinc 17 Pulp 16 Nickel 16 Saw Logs 11 Silver 8 Copper 7 Lead 6 Gas 5 Oil3] Source: U.S. Bureau of Mines and Brascan estimates. In addition, the quality of Canada's reserves looked good to us. The polymetallic nature of many of Canada's orebodies offered a hedge against risk relating to any one metal. Put another way, the by-product metal credits offered a net operating cost advantage with respect to many of the metals mined. Our energy costs also appeared to provide Canada's natural resource industries with an advantage. We considered Canadian mining expertise as amongst the world's finest, as were the exploration equipment and technology developed in Canada. In addition, Canada offered a stable political climate and one we knew. Further, we felt the Canadian Government's future role in the industry would, on balance, be benign, partly because the Canadian content of the mining industry was very high in contrast to the petroleum industry. Granted, we could find cheaper sources of copper; however, to do so would involve venturing into regions where country risks were higher.

Jan 1, 1985

By A. Andreas

New Mexico established an annual record by producing 38,897,741 bbl. of oil during 1940. This was approximately 6 per cent greater than the 1939 production of 36,746,840 bbl. The daily average produc-tion was 106,569 bbl. New Mexico retained its position as the seventh oil-producing state. The recommendations of the United States Bureau of Mines were followed by the Oil Conservation Commission in setting the monthly state allowable. At the beginning of the year the average top allowable for each qc-acre unit was 40 bbl. and at the close of the year it was 36 bbl. Remedial work by the operators has been extremely beneficial and satisfactory in reducing the gas-oil ratios in various fields. Gas formerly blown into the air is now being processed by numerous casinghead plants. The Oil Conservation Commission, with the full cooperation of the Proration Office and operators, has taken bottom-hole pressure surveys and has done considerable remedial work in various fields. Two new oil fields and one gas field were discovered in New Mexico during 1940. Numerous extensions to the existing fields were made. Some of these were definitely wildcats in the same townships designated as fields and some, although called extensions, were more than 3 miles from production. Lea County continued to be the largest oil-producing county in the state, with a production of 33,976,394 bbl. It had the largest number of completions during 1940, with 303 oil wells, 9 gas wells and 13 dry holes—a total of 325 wells. Eddy County was the next most active county, with 239 completions, of which 163 were oil wells, 8 gas wells and 68 dry holes. It produced 4,405,158 bbl. of oil during the year. The increased activity in Eddy County and the completion of a large number of producing oil wells have created a transportation problem that can be solved only by additional pipe-line facilities. During the year Eddy County was unable to produce 1,500,000 bbl. of its allowable oil, because there was no pipe-line outlet. There were 601 wells completed in New Mexico in 1940, of which 478 were oil wells, 22 gas wells and IOI dry holes. This was a decline of approximately 9.5 per cent in the number of completions compared with 1939, when 659 wells were drilled. Southeastern New Mexico Lea County.—The largest producing field in Lea County was the Monument field, with 6,894,475 bbl.; followed by Eunice with 6,559,348 bbl. and Vacuum with 4,743,065 bbl. The Hobbs pool, which for years was the largest producing field in the state of New Mexico, was fourth with 3,790,477 bbl. The Vacuum pool was the most active area, having 68 completions, of which 67 were oil wells and one was a dry hole. Only one new field was discovered in Lea County during 1940; the discovery well was in the Caprock area, the Livermore State No. I, in the SE. 1/4 SE. 1/4 sec. 30, T. 12 S, R. 32 E. This well was drilled to a

Jan 1, 1941

By A. Andreas

New Mexico established an annual record by producing 38,897,741 bbl. of oil during 1940. This was approximately 6 per cent greater than the 1939 production of 36,746,840 bbl. The daily average produc-tion was 106,569 bbl. New Mexico retained its position as the seventh oil-producing state. The recommendations of the United States Bureau of Mines were followed by the Oil Conservation Commission in setting the monthly state allowable. At the beginning of the year the average top allowable for each qc-acre unit was 40 bbl. and at the close of the year it was 36 bbl. Remedial work by the operators has been extremely beneficial and satisfactory in reducing the gas-oil ratios in various fields. Gas formerly blown into the air is now being processed by numerous casinghead plants. The Oil Conservation Commission, with the full cooperation of the Proration Office and operators, has taken bottom-hole pressure surveys and has done considerable remedial work in various fields. Two new oil fields and one gas field were discovered in New Mexico during 1940. Numerous extensions to the existing fields were made. Some of these were definitely wildcats in the same townships designated as fields and some, although called extensions, were more than 3 miles from production. Lea County continued to be the largest oil-producing county in the state, with a production of 33,976,394 bbl. It had the largest number of completions during 1940, with 303 oil wells, 9 gas wells and 13 dry holes—a total of 325 wells. Eddy County was the next most active county, with 239 completions, of which 163 were oil wells, 8 gas wells and 68 dry holes. It produced 4,405,158 bbl. of oil during the year. The increased activity in Eddy County and the completion of a large number of producing oil wells have created a transportation problem that can be solved only by additional pipe-line facilities. During the year Eddy County was unable to produce 1,500,000 bbl. of its allowable oil, because there was no pipe-line outlet. There were 601 wells completed in New Mexico in 1940, of which 478 were oil wells, 22 gas wells and IOI dry holes. This was a decline of approximately 9.5 per cent in the number of completions compared with 1939, when 659 wells were drilled. Southeastern New Mexico Lea County.—The largest producing field in Lea County was the Monument field, with 6,894,475 bbl.; followed by Eunice with 6,559,348 bbl. and Vacuum with 4,743,065 bbl. The Hobbs pool, which for years was the largest producing field in the state of New Mexico, was fourth with 3,790,477 bbl. The Vacuum pool was the most active area, having 68 completions, of which 67 were oil wells and one was a dry hole. Only one new field was discovered in Lea County during 1940; the discovery well was in the Caprock area, the Livermore State No. I, in the SE. 1/4 SE. 1/4 sec. 30, T. 12 S, R. 32 E. This well was drilled to a

Jan 1, 1941

By J. A. Danko, C. D. Pears, L. D. Schmidt, J. P. McGee

This paper describes a pilot plant built on the campus of West Virginia University by the Federal Bureau of Mines station at Morgantown, West Virginia, for gasifying pulverized coal in a mixture of oxygen and steam at pressures in the gasifier up to 450 psig. The work upon which this report is based was done under a cooperative agreement between the Bureau of Mines and the West Virginia University. The goal of Bureau of Mines work at Morgantown is development of a low-cost process for producing mixtures of carbon monoxide and hydrogen for the modified Fischer-Tropsch synthetic-fuel plants, which may be shifted to produce hydrogen for coal-hydrogenation plants. Gasification with oxygen offers the inducement that the gas may be generated at the pressure at which the gas will be utilized in a gas-synthesis plant. Since the optimum pressure for the synthesis appears to be about 400 psig, the gas should be produced at approximately 450 psig to take care of pressure drops in the purification train and control valves. If the gas is generated at the pressure of utilization, only the oxygen need be compressed, not the raw synthesis gas. This means a saving in power of 5 hp per hour per 1000 cu ft (CO + H2), which is approximately a saving of 4 cents per gallon of gasoline. For example, consider a commercial plant generating 18,000,000 standard cubic feet per hour of raw gas that would produce approximately 10,000bbl of liquid product per stream-day. Assume that this gas would be 85 pd CO + H2 and that the oxygen required would be 320 cu ft per 1000 cu ft of CO + H2. The following estimate is based on a commercial centrifugal compressor. If the 18,000,000 std cu ft per hour of synthesis gas is compressed to 450 psig with 74 pd efficiency, 107,000 hp is required for compression. If the synthesis gas is generated at 450 psig pressure, only

Jan 1, 1953

By Hans Lundberg

GEOPHYSICAL methods as described in technical articles generally fail to answer the questions of prospectors and geologists as to which method they should apply and what information they may expect from their application. This article is an attempt to discuss the use of electrical methods with special reference to the prospecting for orebodies and the map¬ping of geologic structure. Especially on virgin ground, geological reconnaissance should precede electrical prospecting, with the object of outlining carefully the orebearing rock and determining the possibilities of elec¬trical prospecting. No electrical survey will then be carried out on ground which, for geological reasons, may be considered barren or where the electrical meth¬ods are inapplicable. As the success of electrical prospecting depends on the difference in conductivity between the ore and the country rock within which the orebody is inclosed, the conductivity of the two should be considered and de¬termined, if possible. The conductivity of an orebody depends on the distribution of conductive ore minerals and, in addition, on its size (length, width and depth). Most minerals with metallic luster show good electrical conductivity; for instance, the sulfides. Zinc-blende is an exception, but as it is often associated with the ore minerals of good conductivity (for instance, pyrite or galena), there is likelihood also of finding zinc.

Jan 1, 1930