Search Documents

By Nicholas J. Grant, Rolf Nordheim, Bill C. Gissen

The system Cb-Re was examined in detail utilizing pure metals, careful melting techniques, and heat treatments. Metallographic and X-my methods were utilized for phase identification. In addition to soli-dus determinations, the composition limits and mode of formation of the intermetallic compounds 0 and X were determined. The binary constitution diagram Cb-Re has been the subject of a number of investigations.'-7 Two intermetallic phases have been described and tentative diagrams have been proposed. It was the aim of this investigation to obtain a complete and more accurate diagram through the use of purer alloys and improved techniques. The diagram worked out by Knapton7 was published after our experiments were concluded. EXPERIMENTAL METHODS The starting materials were Re powder of 99.95 pct purity, supplied by the Chase Brass and Copper Co., and Cb rondelles of 99.6 pct purity, supplied by the Electro Metallurgical Co. Typical analyses are given in Table I. The alloys were prepared from compacted Re powder and Cb rondelles; for critical compositions master alloys were used. The melts varied from 5 to 50 g and were melted nonconsumably in an Heraeus arc furnace, under ti-tanium-gettered laboratory grade argon. It was necessary to invert the buttons and remelt, followed by crushing and further remeltings, the number of which depended on the nature of the fracture of the alloy. The weight of each alloy was carefully checked after each melting operation. It was found that significant weight losses occurred only when loose Re powder was used. These losses amounted to a maximum of 3 wt pct in such instances, but did not occur after the charge was once molten, regardless of the composition. Typical loss of weight after 4 remelts, including crushing, amounted to 0.2 wt pct. Oxygen pickup during successive melting cycles did not appear to be significant, since the weight gain values never exceeded 0.01 wt pct. Control of the composition of the alloys was not too difficult; however, the problem of homogenization was a far greater one. Optimum alloying conditions were finally achieved by a combination of master alloy production and repeated crushing and remelting cycles. The compositions of the alloys utilized to determine the constitution diagram are listed in Table 11. The weight balance method was used ultimately as the sole analytical method, since repeated checks indicated that it was accurate to 0.2 pct, if the weight losses were small. The results were double-checked by a metallographic study of the homogeneity of the samples, since this was presumed to be the more serious factor. Heat treatments at 1200°C or lower were accomplished by sealing the specimens in Vycor tubes, heating in a Globar furnace, followed by air cooling. This was considered to be an adequate quench because of the very low temperatures involved. For temperatures of 1200" to 1900°, alloys were homogenized and heat treated in a tungsten-filament resistance vacuum furnace. From 1900" to 2750" a tantalum-tube resistance furnace was utilized, operating under a vacuum of 105 mm Hg. The temperature measurements up to 1200" were made by means of platinum-platinum 10 pct Rh thermocouples, with an accuracy of 5°C. For temperature measurements greater than 1200°C, optical pyrometers were used. They were calibrated against a standardized instru-

Jan 1, 1962

CONTENTS PAGE UREN, LESTER C.-Increasing Production of Petroleum by Increasing Diameter of Wells. Discussed by A. Beeby Thompson 1 LAHEE, FREDERIC H.-Comparative Study of Well Logs on the Mexia Type of Structure. Discussed by W. A. I. M. van Waterschoot van -der Gracht.... 4 Increasing Production of Petroleum by Increasing Diameter of Wells Discussion of the paper of LESTER C. UREN, presented at the New York Meeting, February, 1925, and issued, as Paper No. 1364-G, with MINING AND METAL-LURGY, October, 1924. A. BEEBY THOMPSON, London, Eng. (written discussion).-The subject discussed in this paper has long been debated by operators in European fields, where very strong views are held regarding the advisability of controlling gas pressures by shutting in wells. While unwilling to theorize on the subject of restricted flow, the writer has always been disposed to associate himself with those who hesitate to impose any obstruction to a natural transitory state that breaks up the oil-containing strata and establishes a feeder system which no subsequent events, natural or artificial, can approach in intensity. In both Russia and Roumania, where the oil is concentrated in discontinuous, disturbed, and irregular lenticles of sand varying, within short distances, in coarseness of grain, extent of impregnation and degree of cementation, it has been the practice to let the wells run wild in order to provoke disruption of strata. By encouraging violent eruptions, an extended feeder system is created and the ejection of enormous quantities of sand, rock, and clay creates a sump and seepage area that it would be difficult to imitate by any artificial means, not excluding actual mining. Before discussing the somewhat novel method suggested for enlarging the infiltration area, the writer would like to confirm the fact that many valuable data applicable to oil are forthcoming from a study of water phenomena. Long association with water-supply problems in many parts of the world has shown how closely the phenomena of underground movements of water and oil are related, so that it is pleasing to note the author's use of water formulas. But there is one great distinction;

Jan 7, 1925

By M. C. Smith, W. V. Green, D. M. Olsen

The creep-rupture behavior of commercial powder-metallurgy molybdenum rod is reported in the temperature range 1600" to 250O°C, at stresses up to 9000 psi and times up to 1 month. The effects of temperature, stress, and grain growth are discussed. Rupture time is fitted to the Larson-Miller parameter and compared to lower-temperature and higher-stress results reported by pugh.1 BECAUSE of its high melting point, molybdenum should retain useful strength to relatively high temperatures. Combined with its ready availability in the United States, this makes it attractive for many applications in missiles, rockets, and so forth—wherever its susceptibility to oxidation can be tolerated or overcome. The mechanical properties of molybdenum rod in the temperature range —200" to 1540°C have been reported by pugh,' Bechtold,' Parke,3 and Carriker and Guard.4 Madden and chen5 have measured the tensile properties of molybdenum single crystals in vacuum up to about 2500°C. As one further step in evaluating its mechanical usefulness, the constant-load creep-rupture properties of commercial powder-metallurgy molybdenum rod have been investigated in the range 1600" to 2500°C. MATERIAL TESTED Creep specimens were machined from 1/2-in. round commercial molybdenum rod, manufactured from powder by pressing, sintering, and swaging. Spectrochemical analysis of the rod showed "traces" (less than 0.01 pct) of silicon, aluminum, chromium, iron, and zirconium, and "faint traces" (less than 0.001 pct) of manganese, magnesium, cobalt, and nickel. Carbon content was 130 to 200 ppm, nitrogen was 110 to 180 ppm, and oxygen 30 to 35 ppm. A typical microstructure of the as-received rod is shown in Fig. 1. Room temperature tensile properties for five specimens strained at about 0.015 in. per in. per min are shown in Table I. CREEP SPECIMENS USED The specimens used for creep-rupture testing are illustrated in Fig. 2. The 1/4-in.-diam gage section was 3/4 in. long, and terminated at shoulders 5 mils high. These shoulders served as fiducial marks for optical strain measurements. Surface finish on the gage section was 16pin. r.m.s. One specimen, for a "long-time" test described below, was modified by dividing the 3/4-in. gage length into three 1/4-in. long sections with individual diameters of 0.250, 0.230, and 0.210 in., each terminating in a pair of fiducial shoulders. TESTING PROCEDURE The constant-load creep-testing machine used has been described by Smith, Olson, and Brown.6 In it the specimen is held vertically on the axis of a cylindrical tantalum or tungsten heater tube by threaded molybdenum or tungsten grips. Both specimen and grips are heated by radiation from the heater-tube, which is heated by its own electrical resistance. The bottom specimen grip is held at its lower end by a clevis pin. The testing load is applied to the specimen through the upper grip by means of hanging weights, a constant force-multiplication lever system, and a pull rod sealed to the chamber lid by a bellows. The incandescent specimen is viewed by an external optical system through slots in the heater-tube and radiation shielding, and an enlarged image of it is projected on a ground-glass screen. Gage-length measurements are made on this image with a pair of cathetometers. Thorium oxide coatings were applied to the threaded ends of most specimens, to prevent diffusion-welding of specimens to grips during testing. Without such a coating welding usually occurred, and grips were often broken by subsequent efforts to remove the tested specimens.

Jan 1, 1960

By O. Hall, V. P. Row

Diamond drilling has become a very important factor in mining. It is the most satisfactory method of obtaining proof of the existence of an orebody and of determining the character and extent of the body in measures where a core can be made. Large investments are based on the information obtained. The method of development, the mine and reduction plants, and subsidiary essentials established are often without other information. The Mond Nickel Co. has drilled about 50,000 ft. (15,240 m.) per yr. for sevéral years and has given considerable study to the question of improving the methods and of overcoming the limitations of this means of securing information. One of the main limitations of the diamond drill has been its inability to drill a straight hole. To depths of 1000 ft. (304 m.) the deflection is often not large but all holes tend to curve and take somewhat erratic courses. A hole running at a small angle to a fissure plane tends to run along the fissure. If the hole is at a large angle, the tendency is to penetrate the fissure plane at right angles. The face of the bit having one side in solid formation beyond the fissure, the other in the selvage of the fissure, tends to turn, the rods curving to the extent of their clearance in the hole. Usually rock measures have somewhat regular fissuring or strata and holes take somewhat similar courses, usually at right angles to the fissuring or strata. Excessive pressure or short or worn core barrels increase curvature. Slow speeds, correct feeds, sharp bits, and core barrels the full size of the bit, tend to decrease curvature but do not prevent it Curvature once started increases rapidly. The disappointments from crooked holes have been numerous. Discoveries have later been found to be on the properties of others. One Canadian company had a hole, supposedly discovering ore 300 ft. (91 m.) from old workings, unexpectedly turn in 8 ft. (2.4 m.) of wooden core from a timber in the old workings. In many cases the information secured by a curved hole is satisfactory, if it can be accurately surveyed. The inclination of the hole at any point

Jan 1, 1920

By Gilbert Santoro

In this study tantalum carbide filaments of various compositions in the fcc region were prepared by heating a tantalum wire in a measured amount of hydrocarbon vapor. Such properties as tensile strength, transverse-rupture strength, microhard-ness, lattice parameter, electrical resistivity, and magnetic susceptibility were measured as a function of carbon content. Some of these properties showed a maximum or a minimum between a carbon-to-tantalum molar ratio of 0.80 and 0.85, the composition range at which the color changes from metallic gray to gold. The recent literature has shown that in the large homogeneity range for the fcc phase of the Ta-C system there is a marked variation for such properties as microhardness,' electrical resistivity, ' thermodynamic properties,z'3 lattice parameter and superconductivity. In addition to the technological interest of these variations within a single phase, important theoretical benefits may ensue from a continuous investigation of properties vs stoichiometry in tantalum carbide and other refractory defect compounds, for example the effect of the metal-metal distance and crystal structure upon bond formation and electronic structure. Whether there is a similar variation of the tensile strength is of practical importance. Of theoretical interest would be the knowledge of how the magnetic susceptibility varies with carbon composition. Both of these properties, as well as the transverse-rupture strength, were determined for tantalum carbide filaments in the fcc phase region. The lattice parameter, the electrical resistivity, and the microhardness were also investigated and compared with values appearing in the literature. EXPERIMENTAL PROCEDURE Material Preparation. Tantalum carbide specimens of various carbon content were prepared by statically carburizing high-purity tantalum filaments in measured quantities of pure hydrocarbon gas. The filaments, which were 10 mil in diameter and 20 or 40 cm long, were heated by their own resistance at temperatures from 1800" to 2200°C using alternating current in some cases and direct current in others. Tantalum wire from two sources was used. One had a reported purity of 99.96 wt pct Ta. The ingot from which this wire was drawn had been electron beam-melted as the final step in its purification. The reported purity of the other wire, which was prepared by a powder metallurgical process, was 99.88 wt pct Ta. The impurities of both tantalum sources are listed in Table I. Spec-trographic-grade toluene or research-grade propane was used as the source of carbon. The apparatus for the carburization of the filaments is shown schematically in Fig. 1. The system was evacuated to 1 x l0-' mm of Hg when using the electron beam-melted tantalum and to less than 1 p when using the less-pure tantalum. Neither the difference in the base vacuum, nor in the hydrocarbon gas, nor in the tantalum filaments resulted in any detectable difference in the properties studied in this work. However, only the carbides prepared from the higher-purity tantalum were used in the magnetic-susceptibility determinations. Once the base vacuum had been reached, the system was flushed with the hydrocarbon and re-evacuated. For any desired composition of the carbide, hydrocarbon gas was allowed to leak into a constant-volume flask to a predetermined pressure. These pressures were measured by a Cartesian diver-type mercury gage with a range from 0 to 20 mm and with a scale expanded to nine times. The hydrocarbon gas was allowed into the reaction tube and the filament was quickly raised to the reaction temperature. The slack in the filament due to thermal expansion was taken up by drawing out the movable electrode with a screw mechanism. The filaments were kept at temperature from a few minutes to 200 hr. In the majority of cases the heating time was 6 hr. The reaction tube was cooled by cascading water on its outer surface. By means of an ammeter and a voltmeter the electrical resistance at the reaction

Jan 1, 1963

By S. Senderoff, D. E. Couch

A PROCESS for the electrolytic preparation of molybdenum from molten salts has been described previously. This previous work centered on electrowinning and electroplating characteristics of the process. In this paper the properties of the process as a refining medium are discussed. In producing metals from ores, it frequently has proven most economical to obtain a comparatively impure metal by smelting, and to purify the product by electro refining. Direct electrowinning from molten salts is rather difficult when a porous diaphragm is required in the process, as in the case of molybdenum, since satisfactory refractory materials for such a diaphragm in molten salts have not yet been developed. In electrorefining, however, a soluble anode is used. By suitable control of anode and cathode current densities, the lower-valent molybdenum compound used in the electrolyte is not oxidized, and a diaphragm is not needed, thus avoiding difficulties which are encountered with other electrowinning processes. Electrorefining may result from two different processes in the cell: Dissolution of the molybdenum and the less noble impurities with a separation of the more noble impurities as an anode sludge; the electrodeposition of molybdenum and the more noble metals at the cathode, leaving the less noble metals in the electrolyte. The amount of separation which occurs in each process is determined by the potential of the operating electrode and the relative concentration of the various species at (or in) that electrode. Since molybdenum has a comparatively noble position in the EMF series in molten alkali halides,2 most refining would be expected to occur at the cathode. In this work only the cathodic process was studied. The objective was to determine to what extent various metallic ions, if they dissolve from the anode or are otherwise introduced, were concentrated in the electrolyte. The necessary conditions for the separation of each and the limiting concentration which may be tolerated in the electrolyte for effective refining were studied. The deposits were chipped from the cathode and analyzed spectrochemically for metallic impurities. Besides determining the major contaminant, a general qualitative analysis was obtained to be sure that other metallic ions were kept at a very low level during each series of runs and to be sure that the baths were not being contaminated accidentally. Samples of the bath, for analysis, were taken at the temperature of operation so there was no chance of selective crystallization during cooling. In this way the ratio of molybdenum in the bath to the other metal could be determined readily. These data permitted a check on the anode efficiency and any volatilization that took place during the electrolysis. Experimental Apparatus—The apparatus as shown in Fig. 1 was used to determine the effect of the various foreign ions upon electrodeposited molybdenum. The entry chamber A allowed the cathodes to be removed without cooling the bath and without allowing oxygen or moisture to enter." The cathodes were made Prom 0.25-in. tungsten rods and were rotated during the electrolysis. The balloon in the lower arm B was inflated with helium after the cathode was drawn up into the upper section for removal. A new cathode was then placed into the entrance chamber A after which the chamber was flushed

Jan 1, 1959

By B. M. Larsen

Jan 1, 1965

By D. C. Hilty, W. Crafts

A qualitative pseudoternary solidification diagram for the Fe-S-O system modified by manganese is proposed and supported by experimental derivation of an isothermal section at 1475°C and substantially 1 pct Mn in the solid-metal phase. The solubility of oxygen in liquid iron containing 1 pct Mn and sulphur contents up to 0.9 pct has been measured at 1600°C and found to increase as the sulphur content exceeds 0.15 pct. AS has been pointed out previously,' all oxide and sulphide inclusions in steel, excluding mechanically entrained matter, result from modifications of the basic Fe-S-O system. Therefore, one method of attack on the problem of the mechanism of deoxida-tion and inclusion formation is to examine the influence of deoxidizers on the Fe-S-O liquidus diagram. This approach has been adopted in work on the subject being carried out at the Metals Research Laboratories of the Electro Metallurgical Co. and has resulted in the postulation of types of solidification diagrams for the Fe-S-O system modified with common deoxidizers. This method has been of considerable assistance in interpretation of the factors affecting the formation of inclusions.' For the most part, however, these diagrams have been highly speculative. They were constructed primarily by inference from the pertinent binary and ternary systems and from the appearance of inclusions produced by specific deoxidizers. Moreover, since the systems contain four or more components, simplifying assumptions and qualifications were necessary in order to permit their representation as modifications of the Fe-S-O diagram. Consequently, experimental confirmation of the type of construction employed for these diagrams is desirable, and the present paper is concerned with such evidence. The addition of manganese to the Fe-S-O system was selected for initial investigation. Manganese is an important component of practically all steel and is, therefore, of fundamental interest. Because of its great affinity for sulphur, manganese has a more profound effect on the sulphide side of the Fe-S-O diagram than any of the other common deoxidizing eletments. In addition, more quantitative information pertaining to the contiguous binary and ternary systems involving iron, manganese, sulphur, and oxygen is available than for the other deoxidizers. Fe(Mn)-S-O Solidification Diagram Many of the side diagrams of interest in connection with this system are known. The Fe-Mn binary has been well established by several investigators;% the Fe-O system has been clarified by Darken and Gurry;' and FeO-MnO diagrams have been published by Herty,5 Andrew, Maddocks, and Howat,6 and by Hay, Howat, and White.7 The Mn-O diagram does not appear to have been derived experimentally, but the portion of 'it that is of interest can be visualized easily from a consideration of the melting points of Mn and MnO and the fact that a broad miscibility gap must exist between them. The ternary Fe-Mn-O diagram has been discussed by Benedicks and Löfquist,8 Wentrup,9 and by Körber and Oelsen.10 Experimental study of the Fe-Mn-O system has been carried out by Körber and Oelsen and to a lesser degree by Chipman, Gero, and Winkler,11 Hilty and Crafts," and others. On the basis of published information, then, an outline of the Fe-Mn-O liquidus diagram can be constructed as illustrated by Fig. 1. In this, as in all succeeding diagrams, transformations such as the ?-? reaction in iron have been ignored for purposes of simplification. The arrows denote falling temperature. The distinguishing feature of this diagram is the broad region of liquid immiscibility extending

Jan 1, 1955

By G. W. Jones

THIS paper describes experiments in which eight test samples of gelatin dynamite were fired in three different types of apparatus and the quantity and composition of the gaseous products of detonation determined. The special dynamites were so prepared that the oxygen balance of the samples varied from -35.0 to +6.0 g. per 100 g. of explosive, including the wrapper. By means of this graded series of explosives, the relation between oxygen balance and gaseous products of detonation could be studied explicitly. The effect of varying oxygen balance on explosive strength has been discussed in another paper.1 The apparatus employed in the work described in the present paper included (1) the Bichel gage, a steel bomb of 15-1. volume; (2) the Crawshaw-Jones confined detonation apparatus, a steel cannon from which the explosive is fired into a pipe of 90-1. volume; and (3) the Hercules tank, an apparatus in which the explosive is confined in a quartz block which is placed in a steel tank of about 4500-1. volume. A full description of the apparatus is given later. VARIABLES AFFECTING COMPOSITION OF DETONATION PRODUCTS The character of the detonation products of commercial explosives is governed in part by the same factors that affect the combustion products from explosive mixtures of air with gases or vapors. In either case, combustible materials-namely, carbon, hydrogen, and sometimes sulfur-are present and combined variously. In an exploding gas mixture the combustibles are oxidized by oxygen in the admixed air, whereas with explosives the necessary oxygen is provided by oxygen-carrying materials in the explosive ingredients.

Jan 1, 1928

By F. J. Martin, W. G. Hubler

The Beattie mine is at about the center of Duparquet township in the Province of Quebec, Canada. It is 22 miles northwest of the town of Noranda. The elevation is approximately 1200 ft. above sea level. This locality, long considered a favorable one from the geological point of view, has been prospected for over 20 years, but no discoveries of economic importance were made until the present orebody was found by John Beattie in 1930. The specific gravity of the ore is 2.77. The gold occurs in intimate association with the sulfides, pyrite and arsenopyrite, which in turn are very finely disseminated in a silicified porphyry. The bulk of the gold is associated with the pyrite, only a small proportion being with the arsenopyrite. There are small amounts of magnetite, ilmenite and chalcopyrite present in the ore. There is also some hematite in the ore that is mined from near the surface in the open pit. Metallurgical Problems and Methods or Attack 1. The ore is extremely hard and resistant to grinding. 2. The sulfide minerals are finely disseminated in the gangue. 3. The gold, in turn, is so intimately associated with the sulfides that grinding to even 5 microns will not release all of the values for cyanidation. 4. It is necessary to make a high ratio of concentration in order to obtain a product sufficiently high in gold to meet high shipping and treatment charges. Hardness of the Ore.—Owing to the extreme resistance of the ore to grinding, it was recognized that grinding costs would be high. Microscopic tests showed that grinding to 95 per cent minus 325 mesh would be necessary to liberate a sufficient amount of the values in order to obtain a tailing assaying 0.02 oz. gold per ton, which is considered to have the economical minimum gold content that can be obtained. It is not feasible to grind this hard low-grade ore (0.18 to 0.20 oz.) to 95 per cent minus 325 mesh, so it was necessary to overcome the problem in another way. The following method was decided upon: (1) Fine crushing to minus 1/4 in.; (2) relatively coarse primary grinding; flotation of low-grade concentrates in the primary and rougher circuits and discarding the

Jan 1, 1935

By Albert Sauveur

(New York Meeting, February, 1913.) IT is delightful to read a technical paper like that of J. E. Johnson, The Effect of High Carbon on the Quality of Charcoal-Iron, presented in October, 1912, at the Cleveland meeting of the American Institute of Mining Engineers.1 The clear, simple, and straightforward manner in which he describes his experiments and results makes you feel as if you had been, so to speak, at his elbow during the course of his investigations, while his method of procedure is so rational that you can fairly anticipate each step in the logical sequence of the tests performed. The following notes suggested by Mr. Johnson's paper are presented here in the hope that they may help, if only a mite, towards the final solution of a problem of considerable scientific and industrial importance.

Jan 3, 1913

By Joel H. Watkins

The terms kaolin, china clay, ball clay, and paper clay are more or less loosely and interchangeably applied to a large class of white-burning clays. These clays are made up chiefly of hydrous amorphous (colloidal) aluminum silicates with variable amounts of free silica and other impurities in small quantities. Occasionally also the term kaolinite is wrongly applied to a white-burning clay, for kaolinite is a mineral of definite chemical composition and definite crystalline form which occurs but sparingly in nature. It is not the purpose of this paper, however, to define or classify clays, or to enter into a discussion of the chemistry of clays. It is rather a general description of the occurrence and methods of mining of a kindred group of clays, and a discussion of their future economic aspect. In the Southern Appalachian States, the mining of white-burning clays has in recent years become an important industry. Although these clays are of several distinct types, which occur in as many localities under different geologic conditions, they are for the most part primarily of the same origin. They are essentially the same in elementary constituents, and are largely consumed in the game industrial arts. From the standpoint of a mining engineer, therefore, and for convenience in comparison and correlation, it should be interesting to discuss them under one heading. Kinds of Clay The most important types of clay which are now being actively mined in the Southern Appalachian States and with which this paper is particularly concerned are the North Carolina, Virginia, and Georgia kaolins or china clays (residual); the South Carolina and Georgia kaolins or paper clays (sedimentary); and the Florida and Tennessee plastic kaolins or ball clays (sedimentary). Other varieties which are interesting but which are as yet of little importance are the pocket deposits of white clay in Augusta County, Virginia, the bauxitic kaolins of Tennessee,

Jan 1, 1915

By J. C. De Haven, Harry Seltz

INTERMETALLIC compounds are formed in many binary metal systems. Some compounds are stable to their melting points, and others decompose at lower transition temperatures. Even those of the first class are dissociated in the liquid state, as indicated by the continuous form of their solubility curves at their melting points'. While the lattice structures of some of these compounds' have been determined, their thermodynamic properties have not been investigated. In this paper is described the determination of the free energy and heat of formation of the compound CdSb, which is of the first class mentioned above, melting congruently at 455° C. This compound shows a rhombic structure, and the lengths of the edges of the elementary cell containing four molecules are: a = 6.52,b=8.60,c=4.16Å2 There are three possible methods of determining the free energy of formation of a compound of this type. The first method, applying the third law of thermodynamics, requires the measurement of its heat capacity preferably to liquid hydrogen temperatures, and a calorimetric determination of its heat of formation. The second method involves the study of the equilibrium of the compound in some gas reaction, such as: CdSb + CO2 = CdO + CO + Sb. From the known free energies of formation of, CdO, CO2 and CO the free energy of formation of CdSb could be calculated. The third method measures the electromotive force of a galvanic cell in which the cell

Jan 1, 1935

By R. E. Lamborn

A summary of oil and gas development in Ohio for 1935 must necessarily be brief. As attention of the state government to the oil and gas industry has never included the collection and compilation of statistics on production, either by producing sands, by counties, by fields, or for the state as a whole, such information as requested in Table 1 of this symposium is impossible to secure for this state. In the absence of production data chief attention must be directed to drilling activity for the year. Information such as can be compiled from various sources, including weekly drilling reports to operating companies and trade journals, is given in the following paragraphs with the realization that the data may not be complete in all its details. Drilling Activity by Fields Drilling activity during 1935 was similar to the preceding year in , that the major operating companies were generally content to drill lease-requirement and offset wells and in that comparatively little effort was made to discover new pools. A compilation of completions recorded in weekly reports to drilling companies and in trade journals show 1022 tests completed for the year in 53 counties of the state. Of this total number, 653 wells were commercial producers and 369 were classed as dry holes. Production was secured in 40 counties from formations ranging in depth to 5700 ft. and ranging in age from Middle Ordovician to upper Pennsyl-vanian. From the standpoint of new production for the year, the most important sands are the Clinton of Silurian age, the Berea of Mississippian age and the Shallow sands of Mississippian above the Berea and of Pennsylvanian age. Trenton Sand Field Production in the field of Trenton sand, which originally included parts of 15 counties in northwestern Ohio, is now on the decline. Seventy-three completions were reported in this field during 1935, of which 33.8 per cent were dry holes. Activity centered in Allen County with 12 completions, two of which were dry holes; in Hardin County with 11 producers; and in Wyandot County with 12 producers and 2 dry holes.

Jan 1, 1936

By R. E. Lamborn

A summary of oil and gas development in Ohio for 1935 must necessarily be brief. As attention of the state government to the oil and gas industry has never included the collection and compilation of statistics on production, either by producing sands, by counties, by fields, or for the state as a whole, such information as requested in Table 1 of this symposium is impossible to secure for this state. In the absence of production data chief attention must be directed to drilling activity for the year. Information such as can be compiled from various sources, including weekly drilling reports to operating companies and trade journals, is given in the following paragraphs with the realization that the data may not be complete in all its details. Drilling Activity by Fields Drilling activity during 1935 was similar to the preceding year in , that the major operating companies were generally content to drill lease-requirement and offset wells and in that comparatively little effort was made to discover new pools. A compilation of completions recorded in weekly reports to drilling companies and in trade journals show 1022 tests completed for the year in 53 counties of the state. Of this total number, 653 wells were commercial producers and 369 were classed as dry holes. Production was secured in 40 counties from formations ranging in depth to 5700 ft. and ranging in age from Middle Ordovician to upper Pennsyl-vanian. From the standpoint of new production for the year, the most important sands are the Clinton of Silurian age, the Berea of Mississippian age and the Shallow sands of Mississippian above the Berea and of Pennsylvanian age. Trenton Sand Field Production in the field of Trenton sand, which originally included parts of 15 counties in northwestern Ohio, is now on the decline. Seventy-three completions were reported in this field during 1935, of which 33.8 per cent were dry holes. Activity centered in Allen County with 12 completions, two of which were dry holes; in Hardin County with 11 producers; and in Wyandot County with 12 producers and 2 dry holes.

Jan 1, 1936

By W. Rostoker, S. Spachner

A N alloy of 50 pct Ni-50 pct Fe is currently manu- factured in tape thickness down to 1/8 mil. In the annealed form, this alloy produces an almost square hysteresis loop. This has generally been related to the fact that by proper rolling and annealing practice a sharp cube, (100) [OOl], texture can be developed. As part of a program directed toward an understanding of the relationships between magnetic properties and structure of tape core materials, analyses were made of preferred orientations in tapes of various thicknesses. Annealed tapes of this alloy in 2, 1, 1/2, ¼, and Y' mil gages were acquired from commercial sources. Pole figures constructed for the 2 and 1 mil tapes showed the expected sharp cube texture. However, the ½, ¼, and ? mil annealed tapes showed no evidence of any preferred orientations. A comparison of two transmission patterns is shown in Fig. 1. The origin of the absence of texture in the tapes of less than 1 mil thickness was explored in some detail. The basic questions were whether the heat treatment for the thinner tapes was wrongly selected, whether the initial cold worked textures were different, or whether the actual thickness of the tape exercised some influence on its annealing characteristics. Quantities of the five gages of tape were acquired in the as-rolled condition just prior to the final anneal. Pole figures of the cold worked textures were constructed for each of the tapes. Eye estimates of in-

Jan 1, 1956

By Arthur McKee

As HEAT is the controlling factor in all smelting operations, it will be .most helpful to make a new set of calculations on the basis of a .unit of fuel burned at the tuyeres to carbon monoxide. This ties together the only two factors in this operation that seem to be constant with respect to each other-the fuel at the tuyere and the air or its oxygen content. If our usual smelting operations, using natural air heated to reasonably obtainable temperatures, furnish sufficient heat above this critical temperature for the purpose, it is doubtful whether additions of oxygen will be of marked benefit. A unit of fuel will not produce a single heat unit more if burned with pure oxygen than if burned with natural air and less heat will be available per unit of fuel by the amount of heat that is carried in by the preheated nitrogen in the natural air of the blast. This is more readily apparent if considered in connection with a heat balance sheet per unit of fuel at the tuyere. The heat available in the stack, as shown by the committee's report, is less by reason of the lower fuel consumption per unit of output assumed in this calculation. The balance sheet for enriched air shows a shortage of the amount of heat usually carried in with the blast; also a lack in the hearth of sufficient heat to melt the 18 per cent. additional metal and slag and in the shaft to the extent of the shaft heat required to heat the 18 per cent. additional stock to the melting point. These heat deficiencies are provided for by the largely increased conversion of carbon monoxide into carbon dioxide, which is assumed, as shown by the following figures: Calculation for natural air: Carbon dioxide 18.4 per cent. (after having eliminated the carbon dioxide from limestone) and 20.8 per cent. of carbon monoxide. Calculation for oxygen-enriched air: Carbon dioxide 28.4 per -cent. and carbon monoxide 23.2 per cent. (no carbon dioxide from stone as lime is charged instead).

Jan 11, 1924

By W. D. Haselton, J. B. Newsom

SAFER, cheaper, and faster sinking of mine openings seems to have been realized with the completion of a borehole 5 ½ ft. in diameter and 1208 ft. deep, in Minnesota, during 1938. Moreover, as the opening is to be used solely for ventilation, its circular cross section, smooth walls and freedom from fire hazard recommend it in comparison with the usual timbered shafts of rectilinear cross section. It should be pointed out that a drill hole sunk without the use of explosives frequently will stand open without support, whereas a shaft sunk by standard procedure using dynamite usually must be timbered because of the wall-shattering effect of explosives. The saving in maintenance resulting from the elimination of timber is obvious. The work was done by Pickands Mather & Co. at its Zenith mine, Ely, Minn. This company wanted a ventilation opening capable of delivering 50,000 cu. ft. of air per minute to the fourteenth level, 1200 ft. below the surface. While several general articles1-3 have described the method used, detailed time and performance records have not been presented before. Moreover, with a method as new as this, it is important to compare the results attained under widely varying conditions. Among the new conditions faced at Ely were some extremely hard rock, a series of vertical fractures, seepage water, and some long stretches of sound rock which, combined with excellent equipment, gave a chance to operate without unusual delays. Developments in boring large holes have generally taken the obvious course of increasing the size of the equipment, a line of attack that has resulted in putting down 3-ft. diameter holes at damsites for studying the foundations4 and in drilling ventilation openings between levels at Butte.5 Such drills operate from the collar of the hole, and the power from the drill is transmitted to the cutting tool through drill rods or pipes. In order to keep down the volume of rock that must be ground to sludge, the cores in large-diameter drilling are made as large in diameter as possible. Their large diameter increases their weight per foot of length, which

Jan 1, 1939

By P. D. Bush, E. H. Gates, M. D. Vijayaraghavan, L. F. Engle

The process developed over the last few years by Republic Steel Corporation in conjunction with Colorado School of Mines Research Institute has been used as a basis for the conceptual engineering of full size plants. The paper will cover the equipment design criteria, equipment design itself, and the integration of the complex unit operations. There are unique features of agitation and use of gas media through- out. The paper will provide an illustrative example of the process requirements for a variety of raw material feeds. It will discuss the materials of construction approach required.

Jan 1, 1973

By M. P. Tixier, F. Segesman

Explanations bused on theory and laboratory tests tire offered for certain unusual features of SP logs which may befog their interpretation, namely the "sawtooth" SP and the reduction or increase of SP with time. The sawtooth SP is frequently seen in SP recordings of thick, very permeable watcr. sands of the Louisiana Gulf Coast. Using SP data from a resistor network analog, this anomaly is explained on the basis of a thin shale streak within the sand. under which the invading filtrate accumulates by gravity segregcitiorr. The electromotive force then appearing across the shale streak gives rise to the anomalous SP. Reduction of the SP on successive logging runs Ira often been observed in very permeable sands when as indicated by the resistivity curves, the invasion depth has been reduced to practically zero. Laboratory results verify that this phenomenon may be due, to the presence of air electromotive force, across the mod rake when the fluids on either side differ in activity. Also, there is, in some cases; an increase of SP deflection on successive logging runs, because the emf initially present across the mud cake disappears as the somewhat saline water just behind the mud cake is progressively flushed out by the invading filtrate.. Field example and laboratory data are presented. I N T R ODUCT1ON Some unusual features are frequently observed on certain SP logs which make interpretation difficult. The purpose of this paper is to offer explanations of several cases of interest. All of these arc related to the conditions of invasion. The cases to be discussed are as follows. 1. The sawtooth SP anomaly which is frequently seen within the thick, highly permeable saltwater sands of the Louisiuana Gulf Coast 1. Reduction of the SP deflection from the usual sand line in very permeable sections when the depth of invasion is practically nil. As will be explained, such a reduction is attributable to a membrane electromotive force across the mud cake. 3. An increase of the SP with time just after the iormation is drilled as a result of progressive flushing of the invaded zone. FUNDAMENTALS OF SP PHENOMENA An explanation of SP phenomena must begin with the following basic ideas. 1. The SP log derives its character from ohmic potential differences in the hole produced by currents flowing through the mud.' These currents are driven by electromotive forces which are primarily electrochemical in origin. Other possible types of SP-producing electromotive forces may be disregarded for the purposes of this paper. 2. The electrochemical emf's associated with permeable formations are now understood to consist of liquid-junction emf's and membrane emf's.',' As schematically shown by thc battery symbols in Fig. 1, the liquid-junction emf, E,,,, exists at the contact between waters of different chemical activities, a,,,, (mud filtrate) and tr,,. (formation water); the shale membrane emf, lS.sn. exists across the adjacent shales whcn they separate waters of different activities. The emf's just cited are additivc in producing SP currents (arrowed circles of Fig. I). Thus, neglecting for the moment any possible membrane emf across thc mud cake, the total electrochemical emf, E,, will be given by their sum, where K,., -! K,q,, = 12 + 59, or 71 at 75 °F. In the log interpretations the SP of a thick sand (i.e.. the static SP) is generally related to the activities of the filtrate and formation water through Eq. 1. by setting the static SP equal to - E,.