Search Documents

By Frank J. Tolonen

BENEFICIATION of iron-bearing formations is one of the major problems of research at the Michigan College of Mining arid Technology. Funds for this purpose hate been supplied by the State of Michigan supplemented by contributions of labor and some supplies from the Federal Government during the depression. The iron-mining companies have cooperated in securing samples and have also furnished much valuable information relative to the various formations.

Jan 1, 1937

By A. L. Mular

Two equations express the integral rate at which fines are produced from a homogeneous material: It has been demonstrated that the Gaudin-Meloy distribution for single fracture is equally applicable to multiple fracture and is related to the Gaudin-Schuhmann distribution at least when the distribution modulus a is close to unity. A, xoY was found to be independent of starting mass over the range studied when particle size was held constant. The equations are related to the input energy to the mill. In an earlier paper,' it was shown that when Mo g of uniformly sized homogeneous material is ground dry in a batch rod mill, the energy-size reduction equation is expressed at any time by the mass of unbroken starting material left at time t, ku is the size modulus of the portion Mo - Mt, and P is a constant that is generally equal to the distribution modulus a. If the power to the mill is constant, Et is proportional to time and Eq. 1 is rewritten where (Mo -Mt)/t is actually the integral rate at which fines are produced from a parent material, and A, is another constant. The size modulus, k,, is determined from the Gaudin-Schuhmann equation:2 where y is the cumulative fraction finer than any size x. Recently, Gaudin and Meloy derived a distribution equation for single fracture on the assumption that the random fracture of a homogeneous material produces daughter particles of similar shape. Their equation is given by where y is the cumulative fraction finer than size X, x, is the size of the unfractured parent, and r is designated the size ratio. Although Eq. 4 is derived for a single event, it should also approximately hold for a series of com-

Jan 1, 1962

The General Electric Co., in cooperation with the Montana School of Mines and under a research grant from the Anaconda Co., is presently experimenting on a new non-explosive method of breaking rock with radio-frequency electrical power. The method is known as electrothermal forcing. It must be understood that present equipment has not been designed to perform primary blasting functions. Its conceived use will be restricted to small pieces of rock too large to pass through a chute or grizzly. However, even this use is still far in the future. Experiments to date have been limited mostly to rock smaller than 18 in.

Jan 11, 1961

By W. C. Phalen

SALT-MAKING PROCESSES THE production of salt in the United States divides itself at the outset into two distinct classes: (1) The mining of rock salt and its purification and separation into marketable sizes, and (2) the production of salt by evaporation from brines, bitterns, and other solutions. The processes employed at the present time in the manufacture of salt by evaporation may be outlined as follows: 1. Solar evaporation. 2. Direct-heat evaporation (a) in open kettles; (b) in open pans. 3. Steam evaporation, (a) in jacketed kettles, (b) in grainers. 4. Vacuum-pan evaporation. In this paper only the solar-evaporation processes practised in different parts of the United States will be described. SOLAR EVAPORATION Localities In the Eastern States the solar-evaporation process is not generally employed for climatic reasons. In the Western States, particularly in California and Utah, the great bulk of the salt produced originates in the solar-evaporation process. Of the Eastern States producing salt, this process, so far as the writer is aware, is employed in New York State only.

Jan 9, 1914

IN the early period of steelmaking, ingot structure and segregation were of no practical importance. Crucible melting required very small ingots that gave little segregation, and a small inserted hot top prevented pipe. As larger ingots were poured from bessemer converters and open-hearth furnaces, segrega- [ ] tion, piping, and gas evolution became increasingly important. The techniques of making semikilled and rimmed ingots were developed with little knowledge of the actual mechanism of the process. The first studies of solidification were made by the Brearleysl and Gathmann,2 who used stearine to show the effects of shrinkage and mold shape. Fig 11-1 is a picture of a series of stearine ingots at various stages of solidification. These studies showed that the liquid solidifies at a nearly uniform rate from the sides and bottom of the mold and demonstrated the formation of

Jan 1, 1951

By H. Ries

Introduction BODIES of pyritic ore in schistose rocks have long been known in different parts of the world. The several occurrences resemble each other in being usually of more or less lenticular shape, inclosed in walls of schist or gneiss, and carrying pyrite, chalcopyrite, and pyrrhotite in varying proportions, as the chief ore minerals. The deposits differ, however, in that sometimes one, sometimes another, of the three sulphides mentioned may predominate. The orebodies in general are more or less closely conformable with the schistosity of the wall rocks, although in cases this may not hold true. The boundaries may or may not be sharp, but in general are fairly distinct. The lenses vary in size, may occur singly, or in groups; in the latter case they may be in line, overlapping, or occasionally parallel. Pinching and swelling of individual lenses is not uncommon. The genesis of these pyritic bodies has provoked much discussion, and they have been variously classed as sedimentary, igneous intrusions, hydrothermal replacements or impregnations, etc. Indeed, in some cases different geologists have most positively assigned widely diverse origins to the same deposit, as in the case of Rio Tinto 1 and Rammelsberg.2 It is true that in the light of modern criteria, we have been able in a few cases to decipher clearly the process of origin and so there seems no doubt now regarding the genesis of the deposits at Rio Tinto, Spain;3 Rammelsberg, Germany ;4 Ducktown, Tenn.;5 southwestern Virginia;6

Jan 8, 1917

By W. M. Robertson

The kinetics of grain boundary groove formation on copper surfaces immersed in liquid lead have been studied over the temperature range of 400° to 900°C. The groove widths were Proportional to the cube root of the annealing time, indicating that the diffusion of copper through the saturated liquid-lead solution is the mechanism by which grooves form. The rate constant for the process can be calculated by a theory due to Mullins. Using published data for the solubility of copper in liquid lead, for the interfacial energy of the solid copper-liquid lead interface, and for the diffusion coefficient of copper in liquid lead, the calculated rate constants almost exactly reproduce the measured values over the entire temperature range. The decay of scratches placed on copper surfaces has also been studied. The rate constant for scratch decay agrees with that for grain boundary groove growth, though scratch decay is sensitive to convection currents in the liquid. The interaction of solid and liquid metals has been studied extensively and has been found to be rather complex. Many of the studies have been complicated by a host of competing effects, including temperature gradients, concentration gradients, the formation of one or more intermetallic phases, natural or forced convection, and the presence in both the solid and liquid of considerable amounts of impurities and alloying elements. Recently theories have been developed of changes in surface profiles driven by capillary forces,' which allow the interaction of the solid and liquid to be analyzed quite directly. The present paper reports a study of the formation of grain boundary grooves on pure copper immersed in liquid lead, which allows the theory to be checked quantitatively. The Cu-Pb equilibrium diagram is quite simple: there are no intermetallic compounds, copper is just slightly soluble in liquid lead, and lead is almost completely insoluble in solid copper.2 The Cu-Pb system has been studied extensively,3-9 and all of the quantities—interfacial energy, diffusion coefficients, and equilibrium solubilities-necessary to calculate the rate of groove growth by a volume-diffusion mechanism are known. The kinetics of grain boundary grooving and scratch smoothing have been studied on the noble metals and the iron group metals in a reducing atmosphere or in vacuum.10 The main interest of these studies has been the determination of surface-diffusion coefficients at metal-gas interfaces using the theories developed by Mullins.1 The present paper uses similar methods for the study of diffusion processes at the interface between two condensed phases. There has been one previous study" of the kinetics of groove growth in a solid-liquid system, which, however, was troubled by the fact that neither interface energies nor diffusion coefficients were known in the Ni-S system studied. THEORY The theory of grain boundary groove growth has been developed by Mullins for the cases of volume diffusion," surface diffusion," and a combination of the two processes.14 He has also analyzed the kinetics of the flattening of a scratched surface by these processes.l5,l6 Several assumptions and approximations were used in the derivations of the surface profile shapes. The applicability of these assumptions and approximations to the present system will be considered in the discussion. At the intersection of a grain boundary with an initially flat interface the equilibrium between the interfacial energy and the grain boundary energy establishes an equilibrium groove angle. This induces curvatures in the interface. The chemical potential of material at a curved interface is higher than at a flat interface, so that material moves away from the region of the grain boundary. Mullins' calculations indicated that the groove profile would be similar to that shown schematically in Fig. 1. Small humps form above the level of the original flat surface. For a volume-diffusion mechanism the separation, w, of these humps at a time, t, is given by and where co is the equilibrium concentration of the solid in the liquid, y, the solid-liquid interfacial free energy, O the volume occupied by a solute atom in the liquid, D the diffusion coefficient of the solid in the liquid, and kT has its usual meaning. For a surface-diffusion mechanism the groove width is proportional to the fourth root of the time. For grooves forming by a combined surface and volume-diffusion mechanism the exponent of the

Jan 1, 1965

By W. J. Millard

It is well known that the excellent mica from Brazil played a most vital role in World War 11. Increased production from Brazil was necessary and with the assent of the Brazilian Government engineers from the united' States went down to study the problem. One of the means advocated by a former Chief of Metals and Minerals Branch of the Board of Economic Warfare, Mr. Carl Schwegler, was the use of stripping machinery. On a pegmatite dike favorable for stripping, a small number of miners could produce as much mica per day as an underground mine employing many times the same number of men. Type of Deposit Favorable The most favorable type of pegmatite for stripping is that which lies more or less parallel to the surface of the slope of a hill. Pegmatite dikes that cut directly into a hill are not suitable for stripping except where a long outcrop extends along the slope. Then just the outcrop could be stripped to some advantage. The ratio at no time should be greater than 1: 3; i.e., I cu. m. of pegmatite to 3 cu. m. of waste, unless the pegmatite was extremely rich throughout the dike. The Economics of Stripping When a mineral is badly needed to win a war, not too much heed can be paid to costs. The object is to produce rapidly and in quantity. Again, a deposit containing a superior grade of mica may be worked although the pegmatite is more costly to work than another deposit containing a considerably greater amount of poor-grade mica. For example: one deposit may have a little mica that will run 11 per cent good stain and better when trimmed and contain 2 kg, of crude mica per cubic meter of pegmatite, while another may run 0.2 per cent of good stain and better, and have a mica content of 10 kg. per cubic meter. A number of stripping projects were found in the vicinity of Raul Soares, Minas Gerais. These were sampled in the various old workings by cutting out a cubic meter of pegmatite and saving the usable mica. Because of the proximity to the surface of most stripping projects, about 34 per cent only of the mica is good for trimming. The other 66 per cent is too badly weathered to be of use. In Table I are given data collected on five properties near Raul Soares. In Table I, "value per cubic meter of pegmatite" means the value of the qualified mica obtainable. This does not include the half trimmed and splittings. By "value per cubic meter of matter" is meant the value of the qualified mica per cubic meter of material excavated; i.e. both waste and pegmatite. This is the figure that should be used to determine whether the operation will be profitable or not, as the cost of stripping is about $0.14 per cubic meter. With new machinery not subject to breakdowns, the cost per cubic meter should be around $0.10 to $0.15. To this should be

Jan 1, 1948

By W. J. Millard

It is well known that the excellent mica from Brazil played a most vital role in World War 11. Increased production from Brazil was necessary and with the assent of the Brazilian Government engineers from the united' States went down to study the problem. One of the means advocated by a former Chief of Metals and Minerals Branch of the Board of Economic Warfare, Mr. Carl Schwegler, was the use of stripping machinery. On a pegmatite dike favorable for stripping, a small number of miners could produce as much mica per day as an underground mine employing many times the same number of men. Type of Deposit Favorable The most favorable type of pegmatite for stripping is that which lies more or less parallel to the surface of the slope of a hill. Pegmatite dikes that cut directly into a hill are not suitable for stripping except where a long outcrop extends along the slope. Then just the outcrop could be stripped to some advantage. The ratio at no time should be greater than 1: 3; i.e., I cu. m. of pegmatite to 3 cu. m. of waste, unless the pegmatite was extremely rich throughout the dike. The Economics of Stripping When a mineral is badly needed to win a war, not too much heed can be paid to costs. The object is to produce rapidly and in quantity. Again, a deposit containing a superior grade of mica may be worked although the pegmatite is more costly to work than another deposit containing a considerably greater amount of poor-grade mica. For example: one deposit may have a little mica that will run 11 per cent good stain and better when trimmed and contain 2 kg, of crude mica per cubic meter of pegmatite, while another may run 0.2 per cent of good stain and better, and have a mica content of 10 kg. per cubic meter. A number of stripping projects were found in the vicinity of Raul Soares, Minas Gerais. These were sampled in the various old workings by cutting out a cubic meter of pegmatite and saving the usable mica. Because of the proximity to the surface of most stripping projects, about 34 per cent only of the mica is good for trimming. The other 66 per cent is too badly weathered to be of use. In Table I are given data collected on five properties near Raul Soares. In Table I, "value per cubic meter of pegmatite" means the value of the qualified mica obtainable. This does not include the half trimmed and splittings. By "value per cubic meter of matter" is meant the value of the qualified mica per cubic meter of material excavated; i.e. both waste and pegmatite. This is the figure that should be used to determine whether the operation will be profitable or not, as the cost of stripping is about $0.14 per cubic meter. With new machinery not subject to breakdowns, the cost per cubic meter should be around $0.10 to $0.15. To this should be

Jan 1, 1948

By G. W. Brock

Experiments in the form of aging of overstrained tension specimens and elevated temperature tension testing, have been carried out on recrystallized arc-cast molybdenum. The aging behavior of molybdenum was found to be strongly dependent on the degree of plastic strain present in the lattice: the reason for this being the low solid solubility for the common interstitial elements in molybdenum. GEORGE W. BROCK, formerly Research Associate, Department of Theoretical and Applied Mechanics, University of Illinois, Urbana, III., is Research Associate, Department of Engineering Sciences, IBM Research Center, Yorktown Heights, N. Y. Manuscript submitted January 19, 1961. IMD THE term strain aging is familiar in connection with the recovery of the yield point in mild steel after tensile overstraining, and there are other instances where it is known to exert an appreciable effect on mechanical properties. For example, steel exhibits a greater tensile strength at mildly elevated temperatures than at room temperature and serrated stress-strain flow curves occur under certain conditions. It has been known for a number of years that the phenomenon of strain aging is directly connected with the presence of carbon and nitrogen in the lattice; and extremely small amounts of either element are sufficient to produce the effect. In this study, the aging behavior of overstrained tensile specimens of recrystallized molybdenum has

Jan 1, 1962

By G. L. Oldright, T. B. Brighton, C. M. Dice

The base bullion from the lead blast furnace contains varying amounts of the impurities left in the smelter feed by the concentrator, regardless of the method of smelter operation. These impurities may be held in part in mechanical suspension rather than being present as true alloys. However, usually there is little free space in the crucible in which to separate these drosses before the bullion is taken from the lead well. When such a dross is melted in a laboratory crucible and allowed to cool, the products obtained are lead bullion, speiss, and matte in well separated layers. Typical analyses of layers are: Analyses. Per Cent Element Bullion Speiss Matte Pb.............................................. 92.0 41.2 38.3 Cu.............................................. 2.4 36.3 40.6 As............................................... 4.0 16.5 4.3 Sb............................................... 0.7 0.2 0.4 S................................................ 0.6 1.9 13.1 Fe............................................... 0.0 0.0 0.0 Totals......................................... 99.7 96.1 96.7 The absence of iron in these products drossed from the blast-furnace bullion proves that the impurities for the greater part are not simply finely divided blast-furnace speiss or matte that has been dissolved or dispersed in the lead, but are held in solution by the liquid metal and rise to its surface as infusible compounds when the temperature of the bath is lowered. In general, the drosses made locally are metal sulphides and arsenides and not oxidized compounds. The large content of metallic lead also does not seem to be retained because of oxidized compounds

Jan 1, 1937

By R. M. Brick

AN increased demand for information in regard to the effect of gaseous elements in steel has accompanied the recognition of the importance of grain size. Attempts to correlate grain-size characteristics with gas con-tent, particularly oxygen in solution or in the form of included metallic oxides, have not been universally successful. Certain definite effects of dissolved gases are recognized; specifically, the role of hydrogen in causing internal cracks or "flakes" and that of nitrogen in preventing excessive grain growth of ferritic chromium steels. When irregular behavior or properties are found in a well-known steel and no definite cause for the abnormality may be assigned on the basis of chemical and metallographic tests, dissolved gases are frequently blamed as the culprits. The solubilities of hydrogen1 and nitrogen2 in pure liquid iron are known but of the ternary systems, iron-alloying element-gas, only the Fe-Si-N3 and Fe-Cr-N systems have received attention and here the study was confined to liquid alloys. Krivobok4 published a curve show-ing the solubility of nitrogen in liquid Fe-Cr alloys but gave no informa-tion on the experimental procedure employed. The considerable experimental work reported on the Cr-N binary alloys has been reviewed by Hansen.5 It is generally agreed that the nitride CrN is a stable phase although the existence of nitrides within limited temperature ranges of stability, viz., Cr3N2 and Cr2N, has been disputed, Adcock6 and others7 have reported a eutectic between Cr and CrN at 1580°C., although the supporting evidence is not complete.

Jan 1, 1940

By Carl Zapffe

JUST as 85 per cent of the total ore produced annually in the United States comes from the Lake Superior region, so does one of its six producing districts-the Mesabi --dominate that region both as to production and total reserves; also in ore Treatment, Mesabi practice is dominant. Therefore, in discussing future reserves or ore treatment one may visualize one big district with five smaller districts as so many satellites. In considering the future less thought need be given to processes than to, economic policies. For thirty years experimental work has now been in progress and every possible ore-treatment process now known has been given attention. This work was started when there was no recognizable danger of running short of ore because of rapid consumption. Thirty years ago the annual production had just progressed beyond the twenty-million bracket for the first time. Today fifty million tons is considered a small production, and last year the aim was for 65 million. At the recent rate of production the life of the estimated reserves of good ore is about 35 years. All who know the local terrain are convinced that, unlike thirty years ago, the chances for discoveries of new big deposits are nil; treatment of lean ores obviously is to become an all-important topic.

Jan 1, 1938

By B. D. Cullity, A. Freda

It is well known that deformation by cold drawing or swaging produces a kind of preferred orientation called fiber texture in metal wires. Such textures have been extensively studied by means of X-ray diffraction, chiefly by techniques in which the diffracted X-rays are recorded photographically. This paper describes some results obtained with a new method, involving the use of a diffractometer. X-RAY METHOD Since the pole figure of a material having a fiber texture is symmetrical about the fiber axis, there is no need to present the entire pole figure. Instead, texture data can be summarized by means of a curve showing the variation of pole density along any meridian of the pole figure, if the north-south axis of the latter is made parallel to the fiber axis. The position of a pole on the meridian is specified by the angle 9 between the pole and the fiber axis (wire axis). The X-ray method1 used here to measure pole density as a function of 9 actually consists of two methods, referred to as A and B. In method a, X-rays are reflected from the wire surface. Pole densities can be measured by this method from O = 90 deg down to a limiting value which is dependent on the Bragg angle 8 and is typically of the order of 30 to 40 deg. Method B involves diffraction from the wire cross section and covers a range of 0 values from 0 up to an angle sufficient to overlap the measurements made by method A. By a combination of the two methods, a complete pole-density curve can be obtained. However, method A alone, which requires no specimen preparation other than etching, can often reveal enough of the pole-density curve to provide complete information about texture components. Both methods require that the measured diffracted intensities be corrected for changes in absorption and diffracting volume with changes in 9. A11 intensities I reported in this paper are corrected diffracted intensities; they are propor-

Jan 1, 1960

By Henry Mulryan

The largest and purest known deposit of diatomite is being actively mined and processed 3 1/2 miles south of Lompoc, Santa Barbara County, Calif., by the Johns-Nlanville Products Corporation. The workings cover 4000 acres, the depth of economically recoverable diatomite being 1000 ft. (Fig. 1). Lompoe, a community of 2500 population, is situated in the Santa Ynez River Valley 10 miles inland from the Pacific Ocean. It is 44 miles

Jan 1, 1938

By Henry Mulryan

The largest and purest known deposit of diatomite is being actively mined and processed 3 1/2 miles south of Lompoc, Santa Barbara County, Calif., by the Johns-Nlanville Products Corporation. The workings cover 4000 acres, the depth of economically recoverable diatomite being 1000 ft. (Fig. 1). Lompoe, a community of 2500 population, is situated in the Santa Ynez River Valley 10 miles inland from the Pacific Ocean. It is 44 miles

Jan 1, 1938

By J. L. O’Brien, M. Suenaga, K. M. Ralls, V. F. Zackay

The effecls of aging a1 400°C on tile resistive transition at 4.2°K of a superconducling 70Zr-30Nb alloy are reporled. Microstrclural changes were studied by critical temperature, resistiue critical field, residual resistiuily, and microhardness measurements and by X-ray diffraction, optical microscoby, ad replication electron microscopy. The result of the aging treat- A defect-free Type 11 superconductor in a magnetic field above Hc1 cannot sustain a transport current runt is a fine array of w-phase pavticles with a mean center to center interparticle spacing of about 800A. At an aging time of 300 hr the maximum onset critical current density is rcached. The particle size at the maximum current density if about 4202. At times longer than 300 hr effective particle impingement leads to lower onset critical current densities. perpendicular to the applied field without power loss in the sample.'-3 This power loss is due to flux line motion caused by the Lorentz force and is manifested by a longitudinal voltage.4-6 When defects are present in the material, flux lines are pinned until the Lorentz force exceeds the "pinning force". That is, it is thought that flux lines reside in free-energy wells existing at the defects, and the critical Lorentz force is that which when integrated over distance will supply the free-energy difference necessary to move the flux

Jan 1, 1968

By WILLIAM E. NEWNAM

THE molding and loading of pig lead has, in the past, been accomplished mainly by the strong arm method and, as the pigs are usually loaded directly into the cars, it has been a hot and laborious task. Of late years it has been difficult to obtain men willing to perform such labor and the need has been felt for loading and molding machinery which would eliminate all manual handling of the hot pigs and which would be sufficiently compact to permit of installation in existing plants with little or no

Jan 1, 1924

J. K. EVELETH, Anaconda, Montana (Communication to the Secretary): Partly for the reasons which Mr. Jones enumerates, and partly because of the presence of copper in greater or less quantities in so large a proportion of the ores throughout this region, I have also found Marguerite's method the most convenient and satisfactory for the determination of iron. In order to avoid the previous precipitation of the copper with H2S on the separation of the iron by means of ammonia, with the consequent necessity for re-precipitation

Jan 1, 1889

By William Kelly, F. H. Armstrong

The object of this paper is to describe the electric equipment at the iron-ore mines of Penn Iron Mining Co., Vulcan, Mich. and of Republic Iron Co., Republic, Mich.; to give the results of tests; and to discuss the methods in use from an operating as well as from an efficiency standpoint. Electricity was introduced at the Penn mines for pumping, hoisting, and compressing air in the spring of 1907, upon the completion of a hydro-electric plant built by that company on the Menominee river about 4 miles from the mines. This plant was described in a paper1 presented before the Lake Superior Mining Institute. A paper2 presented at a meeting of the same Institute describes some of the operating features, and the safety devices of the electric hoist at the Curry shaft were briefly described in the Proceedings of the First Co-operative Safety Congress held under the auspices of the Association of Iron and Steel Electrical Engineers at Milwaukee, Wis., Sept. 30 to Oct. 5, 1912. Generating PoweR Plants After the success of electrical operation was assured, a second set of water wheels and generator was installed at the falls, for which provision had been made in the original design and in the construction of the foundations, and later three additional wires were added to the main transmission line, doubling its capacity and reducing the line loss. The general conditions of this installation are particularly favorable for hydro-electric operation. In the neighborhood of three-fourths of the power used is for mine pumping, which in the main is regular and continuous. For air compressing, power is used for about 18 hr. a day for five days, and 9 hr. for one day in the week, though occasionally when shaft sinking is going on a very small amount of compressed air may be

Jan 1, 1915