Search Documents

By Ellsworth Daggett

THE system of pitwork used with the Cornish pumping engine, and which, for want of a better name, we may call the Cornish system of pitwork, consists essentially of a series of plunger-pumps, situated one below the other, in a shaft or incline, the plungers being operated by a rod called the pitman or pump-rod, which must, therefore, extend from the motor at the surface to the lowest pump. The subject will be best understood by reference to Fig. 1, in which k may be taken as typical of the ordinary plunger-pump, in which S is the suction pipe, u, the lower valve situated in the H piece T; v, the upper valve situated in the valve-box O; I, the mounting-pipe or column through which the water is carried to the surface; L, the plunger-barrel, and P, the plunger working through the stuffing-box, and actuated by the branch rod r, which is attached to the main pump-rod, R. The action of the pump is as follows : On the ascent of the plunger, acting now by suction, the water flows from the reservoir through the valve u, into the barrel, L. On the descent of the plunger, the water is forced up through the valve, v, which acts merely as a check valve, into the pipe, I, through which it is, at each successive down-stroke of the plunger, forced upward until it reaches the next reservoir, from which it is taken by another similar pump, and so on until it reaches the surface or drain-tunnel. The pump is obviously only single-acting, i. e., it acts only during one-half of its entire stroke. The weight of water raised during the up-stroke of the plunger is equal to the weight of a column of water whose base is the area of the plunger and whose height is the mean distance between the plunger-face and the surface of water in the lower reservoir, a distance not usually exceeding 12 or 15 feet, and which obviously cannot under the most favorable circumstances, exceed 25 or 30 feet. The water forced up during the down-stroke is equal to the weight of a column of water whose base equals the area of the plunger and whose height equals the length of the mounting column above the mean position of the plunger-face, say from 150 to 300 feet. Almost all of the useful work, therefore, is done on the de-

Jan 1, 1879

By J. M. Steininger

The mechanism of flotation of sphalerite with sulthydryl compounds of different acidities has been interpreted in terms of chemisorption of unionized collector molecules on hydroxylated zinc surface sites. At a constant collector concentration of 1.5 x 10 -4 M, the upper pH limit of flotation has been found to be directly and closely related to the negative logarithm of the collector acidity constant, pKa The experimental results indicate that flotation is prevented when about 95% of the collector is ionized. At low pH, collector adsorption decreases because of the reduction in number of hydroxylated zinc surface sites. These two effects explain why sphalerite does not float with the more acidic sulfhydryl compounds. Typical anionic collectors for sulfide minerals are short chain xanthates or dithiophosphates which are nearly completely ionized in the generally alka- line flotation circuits.1,2 Flotation mechanisms have therefore been usually interpreted in terms of ionic collector adsorption and competition with ionic depressants of the same sign as the collector. A few attempts have been made, however, to consider adsorption of neutral collector molecules. Contact angle measurements obtained by Wark and cox3 have been interpreted by Cook and Nixon4 as representing adsorption of the free acid molecules on sulfide minerals such as pyrite, galena, chalcopyrite, and sphalerite. Cook and Nixon tried to show that the free acid concentration of the collector was substantially constant along the curves relating collector addition and minimum pH for bubble adherence. However, in a review of the subject,5 Sutherland presented new data on the flotation of pyrite with mercaptobenzothiazole which did not support the hypothesis of constant concentration of either collector ions or collector free molecules. He further showed that, with the assumption of constant occupation of surface sites, both theories lead to relations between pH and collector addition having similar mathematical expressions. In fact, with the more likely assumption of variable occupation of surface sites which results in more complex relationships, it appears impossible to

Jan 1, 1968

By John H. Hollomon

IN a recent paper,1 a very early suggestion by Ludwik2 concerning the nature of the mechanical behavior of metals has been reexamined and extended. In essence it was [ ] suggested that there exists, at least under certain conditions, a mechanical equation of state; that the stress required for flow depends upon the instantaneous values of the strain, strain rate, and temperature, and not upon their past values. It is proposed that under these circumstances the stress does not depend upon past history of these variables, but is like the temperature of a gas that depends only upon the I instantaneous values of the pressure and volume. This notion has not been applied to present day studies of metals, though it is especially applicable to the study of creep. It is the purpose of this paper to analyze the significance and possible range [ ] of applicability of this idea and to deter- mine how it influences the accepted ideas concerning creep. STRESS-STRAIN RELATIONS It is well known that the stress-strain curves of metals are influenced by both strain rate and temperature. For a fixed strain rate and temperature there is associated with each metal a stress-strain curve. If either the strain rate or temperature is changed a new stress-strain curve will be characteristic (Fig. I). A much more general relation between the effects of the sevariables is possible, however. Consider the stress-strain curves of Fig. I determined at

Jan 1, 1946

By C. D. King

THE key to maximum production of ingots for the war effort is maximum production of pig iron. For any given furnace and ore, the most important single influence on blast-furnace production is the quality of the furnace coke. It is generally recognized that undoubtedly deterioration of Pittsburgh coking coals will be accelerated by the depletion of some of the better grades of coal; the extension of mine mechanization, with attendant degradation of coal quality; and the opening of new coal fields, some of which are known to be fairly high in sulphur. All of these factors, contributing as they do to higher ash and sulphur, and not infrequently to inferior quality of coke, made it desirable that an extensive study be undertaken to determine the effect of washing some coals that closely approximate the average chemical composition of coking coals to be expected in the future by the subsidiaries of the United States Steel Corporation in the Pittsburgh district. It was deemed advisable to study the improvement obtained by washing such coals and to determine the need for supplementing the existing coal washery at Clairton to assure continued maximum production of pig iron from presently available furnace stacks. The existence of the coal washer at Clairton made it possible to conduct tests on coals used in raw form and on similar coals after washing. This study covers an investigation of the quality of furnace coke as affected by washing coking coals, and is confined to the use of IOO per cent high-volatile Pittsburgh seam coals from Fayette and Greene Counties in the manufacture of furnace coke. It covers the improvement in chemical and physical properties as well as the degree of uniformity in coke obtained by washing these coals, and includes the effect on blast-furnace production and practice. The test period involved is four months; the plants, Clairton by-product coke plant, and the Carrie No. I and No. 2 blast furnaces at Rankin, Pa., Carnegie- Illinois Steel Corporation. Clairton By-Product Coke Plant And Coal Washer The Clairton by-product coke plant carbonizes 30,800 net tons of coal daily in 22 batteries containing 1482 ovens. Three oven sizes are used, commonly known as wide, medium, and narrow types, recognizing the difference in oven width. These ovens also differ in height and length. The present coal washer has a daily capacity of approximately 14,000 tons, leaving 16,800 tons to be carbonized in raw form. Washed coal is used on all the narrow ovens and on three of the six batteries with ovens of medium width, raw coals being used on all the remaining ovens. The customary arrangement is

Jan 1, 1944

By Hsun Hu

Direct observations were made on the recrystalli-zntion of a cold-rolled (110) [001] crystal of 3 pct Si-Fe by annealing thin sections of the specimen inside the electron microscope during examination. Subgrain formation, presumably by polygonization, occurs rapidly, followed by a slow increase in the subgrain size before recrystallization can be detected. No migration of the subgrain boundaries was observed, and the formation of recrystallization nuclei by coalescence of subgrains is suggested. Re-c~ystallization characteristics of various texture components were individually examined. AS reported in a previous paper: orientations of the various deformation texture components in a 70 pct cold-rolled (110) [0011 crystal of 3 pct Si-Fe were completely confirmed by transmission electron diffraction patterns taken at various areas of the specimen. These orientations can be summarized as follows: Over most areas of the deformed crystal (111) planes are parallel to the surface. These areas correspond to either $- the two main defor: mation textures, the (111) [112] or the (111) [112].2-5 Within a few areas, (100) planes parallel to the surface are frequently found. These areas represent the minor deformation texture component, the (100) [Oll] type, which is derived from rotated Neumann bands.2'4'5 Only in very rare instances are (110) planes found parallel to the surface. This orientation corresponds to the very weak texture component of the (110) [001] type. In a pole figure, this (110) [0011 orientation is located within the orientation spread between the two main (111) [1121 type textures. Usually the electron diffraction patterns taken at various areas of the specimen are very simple ones, i.e., for any one area the pattern consists only of sharply defined spots of a single orientation. In some areas, however, more or less continuous rings of weaker intensities are superimposed on a simple pattern, indicating the presence of a wide range of additional orientations. In order to understand in detail the recrystallization of this cold-worked crystal, the recrywtallization characteristics of each of the various deformation texture components must be examined. This can best be done by using a high-temperature stage and transmission electron microscopy techniques, whereby small areas corresponding to the various texture components can be selected individually for examination. The present paper presents results obtained by this method. MATERIAL AND METHOD Specimens were prepared from a previously studied1 single crystal of a commercial grade 3 pct Si-Fe alloy with an initial orientation (110) [00l], cold-rolled 70 pct from 0.014 in. to 0.004 in. in thickness. Thin foils were prepared by electrolytic polishing as described in the earlier paper.' Specimens of this thin foil were then mounted in a high temperature stage similar to the one designed by Whelan.6 A direct current was used as the heating source. The temperature of the heating grid was calibrated by means of a Pt vs Pt-10 pct Rh thermocouple in a vacuum chamber (0.01 to 0.02µHg). Maximum variation within the temperature range of 250o to 000°C was about ± 25°C. After the desired areas were selected for examination, the specimen was heated to a low temperature for some time while the selected area was constantly watched. When no further change in structure and orientation could be observed, a higher temperature was applied. Photomicrographs and diffraction patterns were taken from time to time during examination, with the heater temporarily turned off* while the photographs were

Jan 1, 1962

By Theodor Knutzen, Charles H. Fulton

The plant of the National Smelting Co., a corporation controlled by the Horseshoe Mining Co., was built during 1901 to smelt the dry siliceous ores of the northern Black Hills, extracting the gold- and silver-values in a matte of low copper-percentage which is shipped to Omaha and Denver for refining. Originally, the plant was designed to collect the values of the siliceous ores in an iron-matte, which mas to be resmelted with lead-ores, in a lead-furnace, the lead-bullion produced to be refined into Doré bullion in English cupelling-furnaces. However, the scarcity of lead-silver ores in the Black Hills, owing to the present non-productiveness of the Galena district, led to

Jan 1, 1905

ALTHOUGH I have already described to you the procedure for making assays of the ores (a thing that is not very different from what I wish to describe in the present chapter), I shall repeat it in substance, with the addition of the method of assaying gold, in order to tell you certain rules for weights which are very necessary to know, and above all in order to demonstrate to you the method of refining a small quantity of silver by the use of a cupel, and in order to tell you how there are (I find) only two ways that are customary for bringing silver to fineness. One is that of the cupel [copella] and the other is that of the cupeling hearth [cenneraccio], one for a small and the other for a large quantity. But although they are called by two names and appear to be two methods, the aim and the procedure of both is actually the same. Nor do I know of other difference between them than the carrying out of the method and the large or small quantity. Cupeling is a very useful thing for anyone who handles gold or silver to know. Indeed it is necessary, because it not only throws light on the work that is to be done but it also shows the truth [55] and the correct weights in large quantities. It is a quicker and easier way of bringing the work to the desired perfection than is afforded by the method for large quantities. Therefore, as you have heard, it is used in making assays in order to know exactly what quantity of the substance of silver or gold is in copper and lead or in ores, as well as in that melted material which remains among the charcoal and ashes. In short, it is the measure by which you have the certainty and safety of knowing that you have not been deceived by art or by your workmen, who had no other interest than their simple wages. Many workmen are found who are so untrustworthy that they no sooner get control of a thing than they think up some fraud, and even though some know that they must give an accounting they do not restrain themselves, although sometimes they would perhaps act with greater security and more deception than they do if they did not fear detection. For, truly, since silver is a valuable thing and every bit is worth much, a man should not enter into refining it with closed eyes. If for no other reason this pro-

Jan 1, 1942

By RALPH HAYES SWEETSER

IRON ore and bituminous coal are the two basic raw materials for the whole iron and steel industry. The ore furnishes the iron and is absolutely necessary-all iron and steel products come directly or in- directly from the iron ores. The bituminous coal furnishes the carbon needed for the smelting of the ores and for the fuel used in all the processes of iron and steel manufacture. The necessary carbon could be furnished in some other form besides bituminous coal. In fact, it is only since the Civil War that bituminous coal has been the chief source of the carbon for metallurgical fuel. For many years only charcoal made from the forests furnished the carbon for smelting iron ores. About 90 years ago, anthracite coal was first used as blast-furnace fuel and for many years continued to be the chief blast furnace and steel making source for carbon. Even in my own blast-furnace experience, I have used charcoal in Canada and anthracite in Pennsylvania for smelting ores in an iron blast furnace. Bituminous coal, now almost exclusively the source for the carbon used in smelting iron ores, also furnishes most of the heat used in the steel-making processes. It is seldom used in blast furnaces in its natural condition, hut is first coked in beehive, or in by-product coke ovens; such bituminous coal is called "coking coal." Bituminous coal that is suitable for making the producer gas used in the open-hearth steel process is called gas coal. Any bituminous coals suitable for making blast-furnace coke or foundry coke, or that can be satisfactorily used for making producer gas, are classed as metallurgical coals and as such are to be considered in my proposed plan for the evaluation of metallurgical coals. According to Bureau of Mines Bulletin No. 449 these coals comprised 22 per cent of the bituminous coals mined in this country in 1923.

Jan 1, 1926

By C. W. Hall

MINE executives, as a rule, have always been willing to adopt new ideas of operation, or to listen to proposals which might increase the effectiveness of their enterprise, more especially so if they could be shown how definite results might be attained by introducing any conception suggested. In these days of high wages, high cost of supplies, and high taxes, operators are even more inclined to accord consideration to innovations or improvements, and many go so far as to employ men to conduct special investigations and make studies for the purpose of advancing production. Where a man is brought into an organization to do work of an efficiency nature, it often creates resentment among the operative heads because of having their work directly scrutinized, or investigated, and there is a tendency, if not actually to obstruct, to fa.il to cooperate; in which case the investigator is handi-

Jan 1, 1925

By John Birkinbine

(New Haven 'Meeting, February, 1909.) AWAKENED public interest in efforts to conserve natural resources will certainly be appreciated by the members of the American Institute of Mining Engineers, and a discussion upon conservation may well form a part of one of the Institute meetings, for the records of papers and discussions which appear in the 38 volumes of its Transactions are replete with evidence of effort's in this direction. Every process which reduces the fuel consumed or the power applied per unit of product; every utilization of waste material, or employment of that formerly rejected, to obtain something of value ; every feature of construction or operation which lessens the labor required or increases the output per employee, is an advance in the direction of true conservation. This may not appear from the records of late conferences or from published articles, in which the effort seems to be concentrated upon reducing the consumption and presenting to the people of the country estimates of exhaustion of natural resources. I rejoice in the awakening of public interest in a matter so important for the present and future welfare of our nation; I appreciate the possibility of much good following conferences of the Governors and delegates from various States and from national societies; and I recognize the interdependence, not only of different States, but of contiguous nations. In fact, the marvelous development of transportation by land and by water, and the decreasing rates at which commodities can be moved great distances, have in many cases practically obliterated geographical boundaries, and nearly every country on the globe can either market its product in other lands or draw upon them for raw or manufactured materials ; hence, conservation is an international subject.

Apr 1, 1909

By R. M. Brick, R. G. Treuting

DESPITE the basic importance of slip in the plastic deformation of metals, and the considerable experimental investigation, thought, and speculation that have been devoted to the fundamental nature of these processes, surprisingly few data have been reported regarding the microscopic appear- [ ] ance and distribution of slip lines,[$] the external manifestation of the slip process. Photographs hitherto reproduced in the literature are in general at low or unspecified magnifications with no correlation to the prior shear. A single-crystal cylindrical tensile specimen of alpha brass about ½ in. in diameter, one of many previously prepared by H. L. Burghoff,1 was available for study. A plane about 3/16 in. wide, parallel to the specimen axis and normal to the plane containing the slip direction and the specimen axis, was ground and metallographically polished along the entire 5-in. gauge length. Heavy etching produced a surface free of both scratches and flow. The specimen was strained in tension until slip markings first became visible on the polished surface (Figs. I and 2). Restressing the crystal caused additional markings to appear at an initially lower [ ] stress than previously was required. Stretching the specimen to produce a dense concentration of slip lines caused such variations in level in the polished surface (normal to the slip direction) that microscopic study at higher magnifications became impossible. After annealing 15 hr. at 850°C., the specimen recrystallized to form two grains with a boundary approximately normal to the specimen axis and about midway along its length. Each was X-rayed, and two planes were again polished along the length of the specimen, in this case each parallel to the slip direction in one of the two crystals. A light longitudinal scratch parallel to the specimen axis was drawn down the center of each plane. A Huggenberger extensometer was attached to the crystal A, whose slip plane would have the higher resolved shear stress of the two, and the specimen was again strained in tension.

Jan 1, 1941

By C. D. King

THE key to maximum production of ingots for the war effort is maximum production of pig iron. For any given furnace and ore, the most important single influence on blast-furnace production is the quality of the furnace coke. It is generally recognized that undoubtedly deterioration of Pittsburgh coking coals will be accelerated by the depletion of some of the better grades' of coal; the extension of mine mechanization, with attendant degradation of coal quality; and the opening of new coal fields, some of which are known to be fairly high in sulphur. All of these factors, contributing as they do to higher ash and sulphur, and not infrequently to inferior quality of coke, made it desirable that an extensive study be undertaken to determine the effect of washing some coals that closely approximate the average chemical composition of coking coals to be expected in the future by the subsidiaries of the United States Steel Corporation in the Pittsburgh district. It was deemed advisable to study the improvement obtained by washing such coals and to determine the need for supplementing the existing coal washery at Clairton to assure continued maximum production of pig iron from presently available furnace stacks. The existence of the coal washer at Clairton made it possible to conduct tests on coals used in raw form and on similar coals after washing. This study covers an investigation of the quality of furnace coke as affected by washing coking coals, and is confined to the use of 100 per cent high-volatile Pittsburgh seam coals from Fayette and Greene Counties in the manufacture of furnace coke. It covers the improvement in chemical and physical properties as well as the degree of uniformity in coke obtained by washing these coals, and includes the effect on blast-furnace production and practice. The test period involved is four months; the plants, Clairton by-product coke plant, and the Carrie No. I and No. 2 blast furnaces at Rankin, Pa., Carnegie-Illinois Steel Corporation. CLAIRTON BY-PRODUCT COKE PLANT AND COAL WASHER The Clairton by-product coke plant carbonizes 30,800 net tons of coal daily in 22 batteries containing 1482 ovens. Three oven sizes are used, commonly known as wide, medium, and narrow types, recognizing the difference in oven width. These ovens also differ in height and length. The present coal washer has a daily capacity of- approximately 14,000 tons, leaving 16,800 tons to be carbonized in raw form. Washed coal is used on all the narrow ovens and on three of the six batteries with ovens of medium width, raw coals being used on all the remaining ovens. The customary arrangement is

Jan 1, 1943

By J. W. Rutter, K. T. Aust

The temperature dependence of the rate of grain boundary migration was measured in bicrystals of zone-refined lead containing from 20 to less than 1 ppm by wezght of tin. The apparent activation energy in the temperature range from 320" to 200oC is markedly dependent upon the solute tin concentration and upon the orientation relationship of the grains adjacent to the grain boundavy. The quantitative experimental observat~ons are compared with the predictions of various theories of grain boundary migration. In previous work.&apos;?&apos; the mobility of individual grain boundaries was studied as a function of impurity concentration and type of boundary. Grain boundary migration occurred at the expense of dislocation arrays which were introduced into the specimen during solidification. Boundary mobility in zone-refined lead at 300°C was markedly decreased by small additions of tin. 0.004 wt pct being sufficient to decrease the rate of grain boundary migration by a factor of 1000. The mobility of grain boundaries having polar orientation relationships near 38 and 22 deg about <Ill>, and 28 deg about <100>, was much less sensitive to tin concentration in the range studied. As a result, these boundaries have relatively high mobilities. The present paper is a continuation of the above study. Data are now presented on the temperature dependence of the motion of individual grain boundaries in zone-refined lead as a function of solute tin concentration and orientation relationship of adjacent grains at the grain boundary. The experimental observations are compared with the predictions of a number of theories of grain boundary migration3-8 which, prior to the present experimental investigation, could not be critically evaluated. EXPERIMENTAL PROCEDURE The striation or lineage structure of melt-grown single crystals of zone-refined lead, containing various additions of tin, was utilized to provide a driving force for grain boundary migration, as previously described.1,2 Each grain boundary under study separated the striated single crystal from another grain which was introduced by localized plastic deformation and recrystallization of a small region of the sample. The speed of migration of grain boundaries in dilute alloys of tin in zone-refined lead was investigated as a function of 1) tin concentration from < 0.0001 to 0.002 wt pct, 2) temperature in the range of 200" to 320°C, and 3) orientation relationship of the adjacent grains at the grain boundary. The substructure driving energy available for grain boundary migration was estimated to be about 4000 ergs per cu cm, within a factor of two, from specimen to specimen.&apos; The specimen dimensions, and growth and alloying procedures for the preparation of striated single crystals of lead of known tin composition, were as described previously.&apos; Each bicrystal was carefully wrapped in aluminum foil, and annealed in a well-stirred salt bath consisting of 50 pct NaNO2 and 50 pct KNO3, for known periods of time at a series of constant temperatures (*2°C). The grain boundary positions, before and after each anneal, were determined by etching lightly in a solution of 5 pct nitric acid in methyl alcohol, in order to follow the motion of the boundary and determine its rate of migration. Thus, the rate of motion of the grain boundary in a single specimen was measured at various temperatures. The above procedure was carried out for each grain boundary in seventeen different bicrystal specimens.

Jan 1, 1960

US 4,194,729 - Sintering of iron oxide ore on a straight sinter belt. The upper strand of the belt is divided into sintering and cooling sections with windboxes for removing their respective gases. The main for collecting cooling gas is located beneath the lower strand and is connected to opposite sides of the windboxes, while the main for collecting sinter exhaust gas is located beneath the lower strand and connected to sinter section windboxes. Both mains are exhausted via gas-evacuating fans and pipes to a flue. Space requirements are lessened and plant accessibility can be maintained at optimum conditions. K. Wacker and F. Feigk, assigned to Dravo Corp. Mar. 25, 1980. 8 pp. (266-144). Filed: 10-30-78 (956,058). Priority: West Germany, 12-16-77 (2,756,082).

Jan 1, 1982

By R. S. McClellan

Western Talc Company, Inc., with headquarters in Los Angeles, Calif., has just completed an extensive modernization and expansion program at its talc mine near Tecopa, Calif., and at its talc and clay mills at Dunn Siding, Calif., the nearest rail shipping point to the mine. The basic objective of the program was to provide facilities necessary to produce 300 tpd of a wide range of ground talc and clay grades for the ceramic, paint, paper, rubber and other industries. In the planning of the program every effort was made to provide a system which would permit a high degree of quality control and uniformity of the finished products, along with efficient operation. Several years ago, R. T. Vanderbilt Co., Inc. purchased Western Talc Co. after a comprehensive investigation of its properties, including an extensive diamond drilling campaign. Western Talc&apos;s properties embraced a number of claims in the Resting Springs mining district in the northern part of San Bernardino Co. and the southern part of Inyo Co., Calif., some seven miles southeast of the town of Tecopa. Operations by the original company were started on a small scale in 1913 and production from that date to the time of purchase of the company by Vanderbilt is estimated at 250,000 tons. The major part of this output was sold to the ceramic wall tile industry.

Jan 3, 1968

DR. PeRsifor Frazer, Philadelphia, Pa. (communication to the Secretary):* Mr. Campbell&apos;s very interesting contribution, after complimentary mention, finally decides against the acceptance of the classification proposed by me in a paper bearing the same title and read at the Wilkes-Barre meeting, May, 1877.2 That paper was written primarily for the Second Geological

Jan 1, 1906

By R. Schuhmann

The expression "unit process " comes up with increasing frequency in discussions among metallurgists and mineral engineers, especially among those concerned with training the next generation. The unit process approach characterizes a significant advance along the road from metallurgy as an empirical art to metallurgy as a branch of engineering. The purposes of this paper are to define and list the unit processes in specific terms, to indicate the scientific and engineering principles basic to all the unit processes, and finally to show how these ideas have been applied to a reorganization of instruction in chemical metallurgy. Unit Operations and Unit Processes Metals are extracted from ores and other raw materials by stepwise procedures. In general, each metallic element is extracted by a different procedure. For many of the metals there is a choice of several flowsheets. However, the procedures all have steps in common. In fact, the many different flowsheets are all made up of a relatively small number of steps which are combined in different groups and sequences. For example, crushing, screening, roasting, sintering, melting, and gaseous reduction are steps which each appear in the Bowsheets for extracting the majority of the metals. The individual steps or flowsheet units can be designated as unit operations or unit processes. These terms are well established in the field of chemical engineering, as the American Institute of Chemical Engineers&apos; definition of chemical engineering shows: " Chemical engineering is that branch of engineering concerned with the development and application of manufacturing processes in which chemical or certain physical changes of materials are involved. These processes may usually be resolved into a coordinated series of unit physical operations and unit chemical processes. The work of the chemical engineer is concerned primarily with the design, construction, and operation of equipment and plants in which these unit operations and processes are applied. Chemistry, physics, and mathematics are the underlying sciences of chemical engineering, and economics its guide in practice."&apos;1a In this definition, the distinction between unit operations and unit processes is that the unit operations are physical while the unit processes are chemical. Table I gives a list of the principal unit operations and unit processes of chemical engineering, taken from Shreve.1b Table 2 lists the principal unit operations and unit processes used for metal extraction. The division between unit operations and unit processes is similar to the chemical engineers&apos; distinction and also correspollds approximately to the division of labor bctween mineral dressing and chemical metallurgy which has been customary in the past. Furthermore, it will be noted that in the proposed classification the unit processes primarily involve chemical reactions and/or changes in state of aggregation; the unit operations primarily do not involve either bulk

Jan 1, 1949

By Joseph Hyde Pratt, Douglas B. Sterrett

Monazite is one of the minerals which, for a long time, was considered somewhat rare in its occurrence, but, upon a commercial demand arising for it, prospectors and engineers soon located large deposits of it in the Carolinas arid Brazil, and the supply has always been able to meet the demand. During 1908 further sources of supply of monazite have been discovered and developed in Idaho. North and South Carolina, however, are the only States that have thus far put any monazite on the market. Monazite is essentially an anhydrous phosphate of the rare-earth metals,ceriunl, lanthanum, and didymium,(Ce,La,Di)PO,. There is nearly always present a varying but small percentage of thoria, Tho2, and silicic acid, SiO2,, which are very probably united in the form of a thorium silicate, ThSiO4. Some mona-zites contain but a fraction of a per cent. of thoria, while others have been recorded that showed the presence of from 18 to 32 per cent.; but the majority contain from 3 to 9 per cent. of this oxide. It is the presence of the thorium oxide that gives the monazite its commercial value. The analysis occasionally shows also the presence of other constituents, as the yttrium and erbium oxides, zirconia, alumina, magnesia, lime, iron oxides, manganese oxide, and titanium oxide. Monazite is light-yellow, honey-yellow, reddish-, brownish-, or greenish-yellop. in color, with a resinous to vitreous luster, and is translucent to subtransparent. It is brittle, with a con-choidal to uneven fracture, and is from 5 to 5.5 in hardness, and from 4.64 to 5.3 in specific gravity. It crystallizes in the monoclinic system, and some crystals have been observed that werc 6 in. in length. The more perfect crystals are,-however,

Jan 1, 1910

By Tomoyuki Moritani, Atsuyuki Mizuno

A concentration of manganese nodule varies areally from 0 to 30 kg/m2 in the central-eastern deep sea bottom of Central Pacific Basin with depth of 5,600-5,900m, but generally it is low, mostly of the abundance order from 0 to less than some kilograms per square metres through the bottom. A high concentration over about l0kg/m is localized to the northwestern basin, besides "St. 414 Deep Sea Hill" and “GH 76-1 Trought”, and also it is likely related with the substratum of deep sea clay. Nodules are tentatively classified into nine types of Sr, SPr, SEr, Db, Ss/SPs, ISs, IDPs and V, in terms of morphology and surface feature. The types may be related with internal structure, nuculeus, mineral composition, chemical composition, occurrence and areal distribution, and might have resulted from various environmental factors of nodule genesis. The abundance of nodule at each station shows the interesting relation with acoustic records by 3.5KHz and seismic reflection profilings. In both the records, thick transparent layer over about 45m thick yield neither any nor significant amount of nodule. The layer less than 45m relates with abundant nodules up to 30kg/m2, though it yield also very little nodule in some cases. The relation suggests that the formation of nodule most likely could be related with the accumulation rate of the post-middle Eocene sedimentary sequence to some extent and also with other controlling factors. The relation can lead us to the tentative delineation of distribution of nodule deposits in the area. The comparative-consideration with the deposits in GH 74-5 area, just east- ward of the present area, shows the areal peculiarity of nodule genesis in deep sea bottom. The results of chemical analyses will be discussed elsewhere.

Jan 1, 1976

President Howe : It is not so clear to me that the facts which Dr. Waldo brings forward really argue that the nature of the combination between copper and aluminum differs from that of the combination between copper and zinc or copper and tin. As regards electric conductivity, I suppose that the fact, which he thinks points to a special intimate kind of union between aluminum and copper, is that the line in his Fig. 1 is neither straight nor uniformly curved, but that its curvature varies rapidly, not to say abruptly. But we find just such variation in like curves for the copper-zinc and copper-tin alloys. Thus, a slight addition of zinc or tin to copper causes a change in color wholly out of proportion to the quantity added; and, as we add zinc or tin to copper, the tenacity rises very greatly, only to fall off abruptly with further additions of either of these metals. Dr. Waldo : My curve related only to electrical conductivity. The President : If irregularity in one physical property argues

Jan 1, 1895