Search Documents

By J. L. Gillson

Historically, rock deposits and sand deposits of titanium minerals came into production about the same time, although there may be some argument as to what is meant by production. Beach deposits of heavy minerals in India (Figs. 1-4) and Brazil (Figs. 5) were worked for monazite about the turn of century, but as there was then no market for titanium minerals, these were thrown away. The rock rutile deposits at Roseland, Va., Fig. 6, were worked to supply rutile for titanium chemicals and for coloring ceramics long before there was a titanium pigment business. The pigment industry started about the middle twenties, both in Europe and the U. S., and almost simultaneously the rock deposits at Ponte Vedra Beach near Jacksonville, Fla., were worked for titanium content. Since those days, production from both types of deposits has continued to grow at a rapid rate; many deposits of both types have been found, and reserves have grown to very large figures. In total tonnage of reserves, there is no doubt that the rock deposits are far ahead of the sand deposits; nevertheless there is a very large tonnage of commercial sands available. It is the quality of titanium mineral in the sand and the relatively lower costs of operating sand deposits that have kept them abreast, at least in annual tonnage produced, with the rock deposits. The principal titanium mineral used is ilmenite, but as soon as that mineral began to be sought as a titanium ore, it was obvious that there are ilmenites and ilmenites. Textbook ilmenite should have the composition FeOTiO2 and should analyze 52.6 pct TiO2 and 36.8 pct iron as Fe. The Indian ilmenite, for almost a generation the standard ore for manufacturing pigment in the U. S., was found to analyze about 60 pct TiO, and only 24 pct. Fe, and most of the iron is in the ferric condition. The whole process of pigment manufacture in the U. S. was built up on the use of a raw material of that grade, and the American chemical engineers who operate the pigment plants shuddered at the thought of using a rock ilmenite with 45 pct or so of TiO, and nearly 40 pct Fe. Intensive search was made around the world to find other deposits of rich black sand, like the Indian beaches, but although a few were found, there was some objectionable feature about each. A deposit in Senegal, south of Dakar (Fig. 7), was worked for a while, but an organic coating on the grains made attack by acid difficult. Modern practice would have included a scrubbing operation, in a caustic soda bath, to eliminate the organic coating. Brazilian deposits were numerous, but individually small, and shipping from them difficult. Deposits on the east coast of Ceylon had many attractive features, but the ilmenite analyzed only 54 pct TiO2 and could have been used only with a penalty. Sand deposits with 2 pct ilmenite, like those now worked in Florida, would not have been considered commercial ore, even if they had been known at that time. Most rock ilmenites are associated or mixed with hematite or magnetite, which accounts for the lower titanium and higher iron values than in the sand ilmenites. The Norwegians, English, and Germans, with cheap Norwegian rock ore at hand, learned to install in their pigment plants adequate capacity on the black side, as it is calltd, and counterbalanced the extra cost of plant, and larger amount of acid used, by the lower cost of ore. When World War II arrived, two of the largest pigment manufacturers in the U. S. had to learn how to use the Adirondack ilmenite, but one of them very gladly went back to sand ores when the Florida deposits came into large-scale production after the war. The other continues to use Adirondack ilmenite and finds it commercially attractive to do so. Rutile is not a raw material for titanium pigment manufacture by the sulfate process, since it is insoluble in sulfuric acid. In addition to its small consumption in chemicals and ceramics it began to be used in quantity in welding rod coatings. With the outbreak of World War 11, and the tremendous need for welding rods in shipbuilding and other structural steel construction, rutile suddenly became in heavy demand. The sand deposits on the eastern shore of Australia (Fig. 8A) which had been worked in a small way since 1934 were brought into production, and some stream placers in Brazil were worked and rutile concentrates shipped to American

Jan 1, 1960

By T. E. Godson

As this is the age of reform, a uniform mining law for North America is a moot subject for discussion at this meeting of the Institute. The question is one of peculiarly technical and, in many respects, local character. We all appreciate the value of the metal-producing industries and recognize the necessity and importance of a well-considered and evenly balanced mining law as a branch of our jurisprudence either for the Provinces or the Dominion as a whole. Mining has taken its place as a foremost industry and legislation that seeks to control and govern it is the concern of not only the active miner but the citizens of the state. A law that, through its charitable measures brings into being the prospector, the pathfinder and superstructure of all mining activity and industry, protects his interests, safeguards invested capital, and encourages and enforces development, possesses at least the salient requirements of a businesslike Act. The manner of doing so is, I think, one of local and internal concern. May I be permitted to say without presumption that of the five mining codes, or Acts, that we have in the Dominion of Canada born and bred within the Provinces of British Columbia, Ontario, Quebec, New Brunswick, and Nova Scotia, some of them could be materially improved. In many respects they do not measure up to the times; they were no doubt creations of merit at the date of their birth but they have not been clothed in seasonable raiment as the years passed by. It is a stern fundamental principle that all natural resources are the inalienable property of the crown. If it is mineral land, then it follows for the protection of the state and the direct advancement of the occupant that the land should be developed as such. The method or machinery by which this must be accomplished is a matter of detail, not of principle. If the right to possession as a licensee depends on discovery, it is not inconsistent with the duty the crown owes to, the state that a grant in fee should pass to the discoverer if there is imposed, after patent issues, a requirement of continuous work or the alternative of an acreage tax sufficiently burdensome to make it unprofitable that the land should be held in an undeveloped state. If, this requirement is recognized, the mental distinction between a grant and lease ceases to exist. A

Jan 4, 1919

By C. Gatlin, C. E. Nemir

A common cure of lost circulation is the introduction of granular bridging agents into the mud system. Many materials, such as ground nut shells, are used for this purpose. If the trouble causing void (fracture, fissure, vug, etc.) is not too large, the granular agent forms a "bridge" across or within the opening. Successively smaller particles in the mud stream then accumulate on and/or within this bridge until normal filtration is finally established. The efficiency of many bridging agents has been studied in the laboratory using various slot testers.',' Many investigators have remarked that a granular bridging material should have the proper particle size distribution. With the exception of the broad range specified in the patent of Goins and Nash,3 here is apparently no definition as to what this distribution should be. A bridge may be initiated when several particles of lost circulation material lodge against each other in a fracture or other void. Smaller particles then may bridge the openings between the larger, previously bridged particles. This process continues until the voids become quite small and the problem becomes one of filtration. It would seem logical that an optimum particle size distribution exists, i.e., one containing the proper quantity of properly sized material to fill the successively smaller voids of the bridge. The filtration characteristics of drilling fluids may be subject to a similar analysis. It has been clearly demonstrated by many workers that the filtration behavior of various muds can be altered by particle size control.'.' Slusser, et al, divided filtration into three periods and showed that particle sizes affecting a given period did not necessarily affect other portions of the filtration curve. An analagous problem is the proper sizing of gravel, liner slots and screen sizes in various sand-exclusion problems. Here the situation is reversed in that a proper "void" size, rather than the size of the bridging agent, is sought. The classic work of Coberly 9 forms the quantitative basis for most sand-exclusion processes. It is interesting to note that, in general, Coberly's work has been overlooked by most drilling-mud researchers. Other investigators have made various studies of the effect of particle size distribution .on drilling-mud properties. As a part of their studies, Fancher and Oliphant reported 30-minute filtration loss of a variety of mixtures of particle sizes.'' Gates and Bowie noted an effect of particle size distribution on filtration, as well as on other physical properties.' MAXIMUM DENSITY THEORY A maximum density mixture has been mentioned as the possible solution for both lost circulation and mud filtration problems. Furnas 12 derived mathematically a method for obtaining maximum density of beds of packed solids, having either a given number of component sizes or a continuous gradation of sizes. This work was verified experimentally by Anderegg.13 or mixtures having a continuous grading of sizes, the interval between sizes is taken as successive screen sizes of interval 2 The ratio of the quantity of each size and the next smaller size is given by the equation Fig. I, number of size intervals of ratio 2 taken from Furnas' paper, gives the value of n + 1 for any given values of + and K, where K is the ratio of the diameter of the smallest particles to the diameter of the largest particles. Measurement by weight assumes, of course, constant density for all particle sizes. Choosing the quantity of the smallest particle size as a unit weight, the required weights of the successively larger interials are then r1 r2 r3 . ®1,2,3. Thus, the grading curve of a maximum density mixture represents a geometric pro gression of ratio r.

By Charles Barrett

THE experiments reported in this paper have been fruitful in disclosing the mechanism of the deformation of iron in compression. They have established the nature of "deformation bands," "etch bands," or "X-bands," that have been a recognized but little understood feature in the structure of cold-worked metals since the early days of metal-lography, and have shown the role of the bands in the development of preferred orientations by cold-working. The work has also shown the relation of the orientation of individual grains to the preferred orientation of the aggregate. Some of the methods previously used in the determination of the indices of slip planes and slip directions are shown to be untrustworthy in the presence of deformation bands. The conclusion is reached that many slip planes and slip directions must operate during each stage in the compression of a single crystal, and that theories failing to take account of this require revision. In conducting the experiments a method f compression has been used by which extreme reductions can easily be reached, even to the limit set by the metal's capacity to deform with-out fracture. The work is a portion of a research program on the plastic properties of iron and steel. It is being used as a foundation for studies of orienta-tions resulting from recrystallization and is being extended to other metals and other types of deformation.

Jan 1, 1938

By G.A. Moore, C. E. Sims

In previous publications of the writers4-7 it has been shown that vacuum extraction of steel can be carried as close to quantitative completion as desired provided the steel is in the austenitic state and sufficiellt time is allowed. For precise work, the method claims preference because the equipmelit for holding and heating the sample can be made simple, and because crucibles, boats, and other unnecessary materials can be eliminated and the blanks thus made very small. It is well known that the evolution rate of hydrogen is smaller just above the trans. formation than immediately below, as would be expected from the increase in solubility when passing into the gamma state. Many attempts have been made to obtain analyses by extraction just below the transition, using times of approxi. mately 2 hr. while it is true that the rate of evolution drops nearly to zero under these conditions, it has repeatedly been shown that the process is incomplete since on raising the temperature into the austenitic range, evolution will be resumed, usually after a, considerable induction period. The low-temperature evolution process appears to be useful in some cases for comparative tests where the residual crror may be more or less constant between samples, For general use, however, there is no guarantee that the error caused by incomplete extraction is constant; hence, the more laborious but more reliable high-temPe'atu'e Process must be used. At high temperature, an original flash evolution, similar to that at lower temperature, is first observed. After not more than an hour, the flash subsides and cvolution settles down to a regular first-order reaction rate for which the half-life* is usually of the order of a few hours for the 5/8-in. diam cylinder at 1050°C. The regular evolution may be followed for whatever period appears justified, after which the residual gas may be estimated as equal to that which was evolved in the last observed half-life period. Tests have shown that the composition of the evolved gas does not vary greatly during the progress of evolution; therefore the residual gas may safely be taken to have the same composition as the portion col-

Jan 1, 1949

By C. E. Sims, G. A. Moore

In previous publications of the writers4-7 it has been shown that vacuum extraction of steel can be carried as close to quantitative completion as desired provided the steel is in the austenitic state and sufficiellt time is allowed. For precise work, the method claims preference because the equipmelit for holding and heating the sample can be made simple, and because crucibles, boats, and other unnecessary materials can be eliminated and the blanks thus made very small. It is well known that the evolution rate of hydrogen is smaller just above the trans. formation than immediately below, as would be expected from the increase in solubility when passing into the gamma state. Many attempts have been made to obtain analyses by extraction just below the transition, using times of approxi. mately 2 hr. while it is true that the rate of evolution drops nearly to zero under these conditions, it has repeatedly been shown that the process is incomplete since on raising the temperature into the austenitic range, evolution will be resumed, usually after a, considerable induction period. The low-temperature evolution process appears to be useful in some cases for comparative tests where the residual crror may be more or less constant between samples, For general use, however, there is no guarantee that the error caused by incomplete extraction is constant; hence, the more laborious but more reliable high-temPe'atu'e Process must be used. At high temperature, an original flash evolution, similar to that at lower temperature, is first observed. After not more than an hour, the flash subsides and cvolution settles down to a regular first-order reaction rate for which the half-life* is usually of the order of a few hours for the 5/8-in. diam cylinder at 1050°C. The regular evolution may be followed for whatever period appears justified, after which the residual gas may be estimated as equal to that which was evolved in the last observed half-life period. Tests have shown that the composition of the evolved gas does not vary greatly during the progress of evolution; therefore the residual gas may safely be taken to have the same composition as the portion col-

Jan 1, 1949

By Byron W. Cheever

Of the elements found in iron and steel, none has attracted more attention than phosphorus. It is considered the great enemy of the steel manufacturer-, and the chief aim has been and is to keep it out by using pure crude material, or when once in, to eliminate it or counteract its effect. Its presence is manifested in various ways, but most of all by producing a condition called cold-shortness. The first question, then, which presents itself is, What per cent. of phosphorus produces this condition ? I have searched very carefully for an answer to this question, but have failed to find one. Authors generally agree that wrought-iron may have a larger per

Jan 1, 1887

By C. E. Sims

In some experimental work conducted several years ago, it was noted that sulphur seemed to have a distinct influence on grain size of carbon steels. 111 order to check this observation, a series of S..A.E. 1040 steels was made with the normal composition held as nearly constant as possible. The steels were made with three sulphur levels, which were 0.012, 0.024 and 0.038 per cent sulphur, respectively. For each of the sulphur levels, steels were made with only silicon deoxidization and with aluminum additions of 0.1015, 0.025, 0.050 and 0.10 per cent. The melting medium was an acid-lined high-frequency induction furnace. These steels were forged and rolled and differentiall!. quenched from temperaturcs in the range of 1500O to 1800°F. After this, the A.S.T.M. grain size was determined and plotted as in Fig. I. It will be noted, first of all, that the aluminum-free steels had filler grain size with higher sulphur when heated to 1500, but that this condition was reversed at 1700°. When aluminum was added to produce fine grain size, the steels in the lowest sulphur level were fine-grained only to 1600°. and then only with an addition of one pound of aluminum per ton. The medium sulphur steels werc fine-grained to 1600' with a wider range of aluminum addition. The steels in the highest sulphur level were fine-grained at 1600° over a still wider range of aluminum additions and fine- grained at 1700° with an addition of one pound per ton. Fig. 2 shows curves of the grain-coarsening temperature for these steels and illustrates how sulphur and aluminum combine to give greater inhibition to grain growth than aluminum alone. Only the highest sulphur steels have a grain-coarsening temperaturc above 1700°.. At 1650°, the low sulphur steel is fine-grained only at its peak, while the highest sulphur steel is fine-grained over a wide range. In these tests, one pound of aluminum per ton gave the best results; this is equivalent to about 1 1/2 lb. per ton for commercial condition. IllcQuaid-Ehn tests made on these steels showed the same trend but to a lesser degree. The tests were repeated on a series of S.A.E:. 1015 steels with sulphur levels of 0.02 and 0.03j per cent. Aluminum additions were made in the range from 0.025 to 0.15 per cent. These steels were forged and rolled, normalized at 2000°F. to put them all in the same starting condition, then reheated to various temperatures from 1600" to 1800" and cooled at rates that would allow ferrite precipitation in the austenitic grain boundaries. The results of these tests arc shown in Fig. 3. It will be noted that. up to the temperature of 1650°, there is very little difference in the grain size obtained from the two levels of sulphur. .At temperatures of 1700° and 1750°, however, the lower sulphur steel was fine-grained only with an aluminum addition of 1 1/2 lb, per ton;

Jan 1, 1945

Reports on process control computer projects at the Kamioka Plant are summarized from the Japanese technical literature (see references). Fluidized Bed Roaster and Sulfuric Acid plant1 A small process control computer (Yokogawa CCS-200 with an OKITAC 5090P 8K central processor) was installed in the Kamioka smelter in the summer of 1964. A year-and-one-half installation project followed, which successfully brought the roaster and acid converters under computer control. The process plant consisted of two 130 RPD fluosolids roasters and two Monsan to acid units. The roasters are charged with lead-zinc concentrates with SO2 from the roaster processed to sulfuric acid. The computer system provides the following functions: 1) log data from the plant--the input is taken from 50 analog signals, 130 high-low digital alarm points, and 50 analog high- low alarm points; 2) set-point control on 18 control loops; 3) direct digital control (DDC) on eight control loops for which conventional controllers were difficult to adapt due to abnormal loop characteristics or delay times; 4) execution of a safe shut-down procedure

Jan 1, 1969

By E. E. Underwood, L. L. Marsh

Aluminum single crystals, alloyed with 0.042 atomic pet Cu and 0.11 and 1.1 atomic pct Mg, were subjected to constant stress creep tests, tensile tests, and hot hardness measurements within a temperature range of 300° to 866OK. Calculations based on Dorn's temperature-compensated time parameter, 6, gave a value of DH, = 27,000 cal per mol for the activation energy of early creep in aluminum single crystals. Correlations have been obtained for aluminum alloy single crystals with the parameter E for solid solution strengthening, as well as with the parameter F for solid solution hardening, by using a valence of three for aluminum. Limited measurements on tensile specimens show that the slip band density tends to decrease with increasing temperature and with decreasing solute concentration. INCREASING interest is being shown in the mechanisms of plastic deformation in single crystals during tensile and creep testing. The complexity of deformational processes in polycrystalline materials has led to a search for simpler experimental conditions. Numerous creep and tensile investigations have been conducted with pure, metallic single crystals. To a lesser degree, the effects of alloying elements on the tensile properties of single crystals have been determined. However: the literature dealing with the effects of alloying additions in single crystals under creep conditions is vanishingly small. This paper represents an attempt to narrow this gap in the knowledge of the subject. Previous investigations of creep behavior at the Battelle Memorial Institute1-1 have been of great value in the analysis of the present single crystal data. It is equally desirable, however, to ascertain the extent of correspondence between the behavior of single crystal and polycrystalline materials. For this purpose, correlations, similar to those developed for polycrystalline aluminum alloys by Dorn and co-workers, have been made with the single crystal data. The results from this study have tended to confirm and extend those correlations to the case of alloyed single crystals. Materials and Procedures Three dilute binary aluminum alloys were prepared for this investigation from 99.99 + wt pct Al, 99.8 wt pct Mg, and 99.92 wt pct (electrolytic) Cu. The nominal compositions of the alloys were 0.042 atomic pct Cu, and 0.11 and 1.1 atomic pet Mg. Precautions were taken to avoid contamination of the stock during melting and casting of the alloys. After a heat treatment of 8 hr at 925°F the alloys were extruded, then machined into) threaded tensile specimens with a 3 in. reduced section and a 0.505 in. diam. Spectrographic examination showed less than 47 ppm metallic impurities in each alloy. The single crystals were grown by the strain-anneal method, with a critical strain of about 11/4 pet giving the optimum results. In general, 3 in. crystals were obtained with the Al-Cu alloy, but smaller crystals in the magnesium alloys necessitated the use of 2 in. and 1 in. gage lengths with the low and high magnesium alloy specimens, respectively. After an electrolytic polish, the orientation of that portion of the specimen containing the largest single crystal was determined from Laue back-reflection photographs. Tensile tests were conducted at a constant load rate of about 2 lb per min. Creep runs were made in a constant temperature room, under constant stress at the higher creep temperatures, and constant load at the lower temperatures. The eloneation was measured to within ±5 microin. by a specially designed capacitance extensometer. The ex-tensometer arms were attached to the 3 in. specimens at the shoulders of the test piece or, where the crystals were smaller than 3 in., by knife-edge grips.

Jan 1, 1957

By E. H. Dix

During an investigation of high-strength manganese bronze by til Engineering Division of the Air Service, at McCook Field, Dayton, Ohio, particles of a "blue constituent" were noted in the microstructure of most of the bronzes examined. The constitution of the simple copper-zinc base alloy is still a matter of dispute in spite of the fact that the copper-zinc series is one of the oldest industrially important groups of alloys, and has received thc carly co~l+itlcl-ntio11 of scirntific rcsc:trch. Thc diagram, according to the rnost rcrent \vork.' IS shown in Fig. 1. The disputed questions involve the tcrmi~r:~tiorl of the beta field and the lint at 470' C. The parliest expc~imc>ntcr, Rol)erts--~1~11stcri, detectrd an arrest in some of his cooling curves :it approximately this temperature and ascribed them to the formation of a cutectic; it has since been proved that there arc no eutectics in this series. Shepherd? was unable to detect any thermal arrests at this temperature, his. diagram was essentially as shown in Fig. 1, except that the line at 470" ('. was omitted and the beta phase carried down to normal temperature. 1,:ttcr. carpenter and Edwards, by a very painstaking research, definitely established the authenticity of the line but attributed it to the breakdown of the BETA constituent into a cutectoid of alpha and gamma. microscopic evidence of the formation of the cutectoid is doubtful and it seems more likely to he due to an allo-tropic change in the beta constituent as shown by Fig. 1. At least for practical purpose?, it is more convenient to think of the structure of a 60-40 brass as a mixture of alpha and beta prime crystals rather thin alpha plus an unresoluble eutectoid of "apparent beta" as it has often been called. * Chief, Metals branch, Engineering Division, Air Service. 1 0. F. Hudson: Jnl. Inst. of hlvtals (1913) 12, 2 E. S. Shepherd: Jnl. Phys Chrm. (10141 8, 421. H. C. H. Carpenter and O. A. Edwards: Jnl, Inst. of Metals (1911) 5, 127.

Jan 1, 1923

By E. H. Dix

During an investigation of high-strength manganese bronze by til Engineering Division of the Air Service, at McCook Field, Dayton, Ohio, particles of a "blue constituent" were noted in the microstructure of most of the bronzes examined. The constitution of the simple copper-zinc base alloy is still a matter of dispute in spite of the fact that the copper-zinc series is one of the oldest industrially important groups of alloys, and has received thc carly co~l+itlcl-ntio11 of scirntific rcsc:trch. Thc diagram, according to the rnost rcrent \vork.' IS shown in Fig. 1. The disputed questions involve the tcrmi~r:~tiorl of the beta field and the lint at 470' C. The parliest expc~imc>ntcr, Rol)erts--~1~11stcri, detectrd an arrest in some of his cooling curves :it approximately this temperature and ascribed them to the formation of a cutectic; it has since been proved that there arc no eutectics in this series. Shepherd? was unable to detect any thermal arrests at this temperature, his. diagram was essentially as shown in Fig. 1, except that the line at 470" ('. was omitted and the beta phase carried down to normal temperature. 1,:ttcr. carpenter and Edwards, by a very painstaking research, definitely established the authenticity of the line but attributed it to the breakdown of the BETA constituent into a cutectoid of alpha and gamma. microscopic evidence of the formation of the cutectoid is doubtful and it seems more likely to he due to an allo-tropic change in the beta constituent as shown by Fig. 1. At least for practical purpose?, it is more convenient to think of the structure of a 60-40 brass as a mixture of alpha and beta prime crystals rather thin alpha plus an unresoluble eutectoid of "apparent beta" as it has often been called. * Chief, Metals branch, Engineering Division, Air Service. 1 0. F. Hudson: Jnl. Inst. of hlvtals (1913) 12, 2 E. S. Shepherd: Jnl. Phys Chrm. (10141 8, 421. H. C. H. Carpenter and O. A. Edwards: Jnl, Inst. of Metals (1911) 5, 127.

Jan 1, 1923

By E. C. Franz

IN an effort to understand high cycle fatigue, as well as to study the mechanism of fracture in general, a number of researches have been undertaken whereby the fracture properties of a metal have been determined under conditions of repeated cyclic prestsain employing high strains with relatively few cycles. Liu, Lynch, Ripling, and Sachs' showed the effect of a definite strain history consisting of small increments of tensile or compressive prestrain upon the flow and fracture characteristics of metals after a limited number of repeated loadings. Liu and SachsW emonstrated by cyclic straining of the aluminum alloy 24s-T4 that the least reduction in ductility was obtained when the compressive stress was nearly equal to the tensile stress. Attempts have been made to correlate the reduction in ductility under such prestraining with conventional fatigue data, as was done by Liu and co-workers.' The following research was conducted to determine if such reduction as has been noted could be correlated with conventional fatigue data or whether the effect resulted from causes extraneous to the basic mechanism of fatigue failure such as strain aging. It might be pointed out in this connection that the reduction in ductility has occurred in alloys that might be susceptible to strain aging or similar behavior, such as alloy 24s-T4. In the present investigation, the test specimens were prepared from the aluminum alloy 75s-T6 and annealed electrolytic copper. Alloy 75s-T6 is a complex precipitation hardenable alloy, whereas electrolytic copper would not be expected to exhibit strain aging effects, particularly at room temperature. The experimental procedure consisted of prestraining test specimens repeatedly by increasing tension in small increments to various total prestrain values, followed by testing to failure in a tension test. The prestraining as well as the final testing was performed on a tensile machine using special fixtures9 0 maintain concentricity of the specimens. After prestraining, the specimens were unloaded as rapidly as possible and immediately reloaded so that the total time lapse between strains was held to a few seconds. Logarithmic or true natural strain was used in all calculations. The results are presented in Figs. 1 and 2. In Fig. 1, the retained ductility, area after prestrain area at fracture is plotted against the tensile prestrain, initial area area after prestrain as abscissa with the number of stress reversals executed to attain the required prestrain plotted as parameter. Several specimens that fractured during

Jan 1, 1955

By R. W. Parsons, P. R. Chaney

Oil recovery by the imbibition mechanism can be important in fractured carbonate reservoirs with a bottom water drive. Laboratory experiments were performed on water-wet carbonate rocks to model this process. The results are interpreted in light of the applicable scaling laws. The imbibition production behavior of a pillar of rock subjected to a slowly rising water table can be synthesized from data on total immersion experiments on small rock samples. If the rate of water table rise is slow enough and if the physical properties are such that the imbibition zone is of a small vertical extent, then only the final oil recovery on the small samples need be known. Applying laboratory imbibition data to a real reservoir should be done with caution because of possible wettability problems and the unknown behavior of two-phase flow in fractures. INTRODUCTION The spontaneous taking up of a preferential wetting fluid into a porous medium with the simultaneous expulsion of the contained fluid is termed imbibition. One of the many physical imbibition processes is the production of oil by the taking up of water into a water-wet reservoir rock. In certain types of heterogeneous reservoirs, e.g., fractured, it is realized that imbibition alone may be the dominant mechanism. Theoretical studies of imbibition oil recovery have followed several lines of attack. The behavior of certain mathematically tractable and conceptually simple models have been analyzed. Birks1 considered a bundle of vertical capillaries model, while Perotti et al.2 and Kelemen3 used a model of a series of vertically oriented fractures. If the oil production behavior from a block of reservoir rock is known, then the cumulative behavior of a vertical stack of these blocks subjected to a rising water table can be determined by a method outlined by Aronofsky et al. 4 Knowing the capillary pressure and relative permeability functions should uniquely set the imbibition behavior for a given sample. Solutions of the partial differential equations describing the process, however, present some formidable problems. Digital computer techniques have been applied to displacement processes in which the capillary pressure has been included.5"8 More recently, similar techniques have been used by Blair 9 to calculate countercurrent imbibition behavior. The fact that imbibition behavior is described by the usual fluid flow equations (Darcy's Law and continuity equation) implies that the derived scaling laws should apply equally to this situation. Use of model experiments to study imbibition has been employed by Graham and Richardson 10 and Mattax and Kyte,11 who actually tested the scaling law applicability. This study is concerned with scaled model imbibition experiments on water-wet carbonate rocks. Of particular interest is the slowly rising water table experiment. This simulates a highly fractured reservoir with the water table rising uniformly through the vertical fracture system. Experiments were performed on different sized samples and with different rates of rise of the water-oil interface surrounding the rock pillar. Total immersion imbibition experiments on smaller rock samples were performed to test the basic linear scaling laws and to see if these simpler tests could be used to synthesize the rising water table experimental results. THEORY IMBIBITION SCALING LAWS Scaling laws for the flow of two incompressible immiscible fluids in a porous medium have been presented by Rapoport.12 These are derived directly from Darcy's Law for the individual phases and the continuity equation. Results from a laboratory model experiment will duplicate those from some reservoir prototype if a constant proportion is maintained among the three forces acting on the fluids — the capillary pressure gradient, the gravitational gradient and the flowing pressure gradient. Operation of the model (i.e., fluid injection or withdrawal) must be conducted in accordance with specific equations. If the

Jan 1, 1967

By A. L. Engel

STRICTLY speaking, ore-dressing does not commence until after the ore is in the mill bins, but where complex ores are treated and their minerals separated to make the best commercial concentrate with the lowest economical tailing, ore-dressing problems begin and often center in the mine itself. This does not refer to the grade of the ore, but rather to the frequent condition in which metallurgical results radically different from customary are obtained because of changes in the character of the ore treated. Different varieties of ore can usually be identified as coming from well-defined depths or zones in the mine, or from known sections of the orebody. Varying degrees of alteration of the ore, inclusions of harmful gangue material, or variations in the quantities of component metallic minerals are often causes of temporarily bad metallurgical results in otherwise successfully operated plants, especially those employing differential flotation to. recover several valuable minerals contained in the ore.

Jan 1, 1931

By C. L. Baker

The total production of petroleum in the Gulf Coast in 1927 was 54.541.180 bbl., .5.655.665 bbl. more than in 1926. The Texas total was 49.129.910 bbl. (Table 1) and the Louisiana tota1 5.411.270 bbl. (Table 2). Louisiana production decreased 278.028 bbl., compared with that of 1926. Spindletop produced nearly 44 per cent. of the Texas total. Initial production in Louisiana amounted to 62.865 bbl. and in Texas to 352.955 bbl.' The Oil and Gas Journal gives a total of 1145 wells

Jan 1, 1928

ALABAMA Altoona.-Cain, J. America.-Foreman, J. T. Anniston.-Cowie, L. K. Foster, R. N. Rogers, R. F. White, H. E. Ashland.-Sturdevant, J. C. Bessemer. Ball, E. M. McKenzie. W. C., Jr. Morgan, C. Birmingham.-Abbott, C. E. Adler, J. E. Aldrich, T. H. Aldrich, T. H., Jr. Ashton, J. J. Burgin, G. E.

Jan 1, 1923

By H. H. Kaveler, W. R. Evans, Jack Tarner

The geological features, development history and engineering detail of the Shuler Field and the results of approximately two years of unitized operation of the Shuler Jones Sand Pool, were discussed in a prior publication.' The purpose of this paper is to present the results of pressure maintenance in the Shuler Jones Sand Pool after nine years of unit operation. GENERAL INFORMATION The Shuler Jones Sand Pool is located in and about Section 18, Township 18 South, Range 17 West, Union County, Ark. The pool was discovered .in September, 1937, unitized in February, 1941, and subjected to gas injection operations in July, 1941. Water was first returned to the reservoir in July, 1944. The reservoir is an anticlinal trap covering about 4,000 acres. The 154,000 acre-ft of sandstone initially consisted of approximately 150,000 acre-ft of productive oil zone and 4,000 acre-ft of gas-cap. The average depth of production is 7,400 ft. Maximum closure of the reservoir is 135 ft and the oil column lies between a gas-oil contact at -7,270 ft and a water-oil contact at -7,370 to -7,380 ft. The field is approximately four miles long. east and .west, and one and one-half miles wide. The sand grains are angular and vary from fine to medium size. The porosity of the sandstone averages 20.2 per cent. The specific permeability averages 400 md. Some zones have as high as 30 per cent porosity and specific permeability of 4,000 md. The reservoir rock is not uniform in character but consists of sandstone zones interspersed with shale. The variation in rock characteristics is evident in the electric log and core analyses presented in the original publication. Asphalt present in the pore space of the sandstone limited the reservoir to the southeast and apparently blocked any encroachment of water from that direction. The initial reservoir pressure at a subsea depth of 7,300 ft was 3,520 psi. The reservoir temperature was 198ºF. Initially, the solution gas volume was 765 cu ft per bbl and the reservoir volume factor was 1.45. The gas solubility and formation-volume-factors of the reservoir liquid are related with reservoir pressures above 300 psi as follows: Solution gas, cu ft per cu ft, S = 0.0334 P + 18.65 Formation volume factor of reservoir oil, FVF = 8.0 x 10 -5 P + 1.168 Gas volume factor, standard cu ft of gas equivalent to one cu ft of gas at reservoir conditions of temperature and pressure, F = .062 P - 4 Pressure (P) measured in psia. The equation for the gas volume factor presented above is based on a direct measurement of a sample of the gas and is a correction of that used in the original paper. The gravity of the oil produced is from 32 to 34" API. CALCULATION OF INITIAL OIL IN PLACE The Jones Sand production history is interesting because it lends itself to analysis by material balance. Production statistics from discovery of the Jones Sand through 1949 and material balance calculations of the initial stock tank oil in place are shown in Table I. The usual procedure in testing the application of material balance calculations is to compute the apparent initial volume of oil in place, using production and pressure information obtained at different time periods. If the apparent oil in place volumes computed increase with successive time periods, water encroachment is indicated and approximations must be mads to correct for its influence. The first requirement in utilizing such calculations is reliable reservoir pressure, accumulated gas, oil and water production, and PVT data. Calculations of apparent oil in place in the Jones Pool, based on field data

Jan 1, 1951

By W. R. Evans, H. H. Kaveler, Jack Tarner

The geological features, development history and engineering detail of the Shuler Field and the results of approximately two years of unitized operation of the Shuler Jones Sand Pool, were discussed in a prior publication.' The purpose of this paper is to present the results of pressure maintenance in the Shuler Jones Sand Pool after nine years of unit operation. GENERAL INFORMATION The Shuler Jones Sand Pool is located in and about Section 18, Township 18 South, Range 17 West, Union County, Ark. The pool was discovered .in September, 1937, unitized in February, 1941, and subjected to gas injection operations in July, 1941. Water was first returned to the reservoir in July, 1944. The reservoir is an anticlinal trap covering about 4,000 acres. The 154,000 acre-ft of sandstone initially consisted of approximately 150,000 acre-ft of productive oil zone and 4,000 acre-ft of gas-cap. The average depth of production is 7,400 ft. Maximum closure of the reservoir is 135 ft and the oil column lies between a gas-oil contact at -7,270 ft and a water-oil contact at -7,370 to -7,380 ft. The field is approximately four miles long. east and .west, and one and one-half miles wide. The sand grains are angular and vary from fine to medium size. The porosity of the sandstone averages 20.2 per cent. The specific permeability averages 400 md. Some zones have as high as 30 per cent porosity and specific permeability of 4,000 md. The reservoir rock is not uniform in character but consists of sandstone zones interspersed with shale. The variation in rock characteristics is evident in the electric log and core analyses presented in the original publication. Asphalt present in the pore space of the sandstone limited the reservoir to the southeast and apparently blocked any encroachment of water from that direction. The initial reservoir pressure at a subsea depth of 7,300 ft was 3,520 psi. The reservoir temperature was 198ºF. Initially, the solution gas volume was 765 cu ft per bbl and the reservoir volume factor was 1.45. The gas solubility and formation-volume-factors of the reservoir liquid are related with reservoir pressures above 300 psi as follows: Solution gas, cu ft per cu ft, S = 0.0334 P + 18.65 Formation volume factor of reservoir oil, FVF = 8.0 x 10 -5 P + 1.168 Gas volume factor, standard cu ft of gas equivalent to one cu ft of gas at reservoir conditions of temperature and pressure, F = .062 P - 4 Pressure (P) measured in psia. The equation for the gas volume factor presented above is based on a direct measurement of a sample of the gas and is a correction of that used in the original paper. The gravity of the oil produced is from 32 to 34" API. CALCULATION OF INITIAL OIL IN PLACE The Jones Sand production history is interesting because it lends itself to analysis by material balance. Production statistics from discovery of the Jones Sand through 1949 and material balance calculations of the initial stock tank oil in place are shown in Table I. The usual procedure in testing the application of material balance calculations is to compute the apparent initial volume of oil in place, using production and pressure information obtained at different time periods. If the apparent oil in place volumes computed increase with successive time periods, water encroachment is indicated and approximations must be mads to correct for its influence. The first requirement in utilizing such calculations is reliable reservoir pressure, accumulated gas, oil and water production, and PVT data. Calculations of apparent oil in place in the Jones Pool, based on field data

Jan 1, 1951

By R. C. Wilmoth, R. D. Hill, R. B. Scott

A cost breakdown is given for reclamation and mine drainage abatement conducted by the Federal Water Quality Administration's demonstration project near Elkins, W. Va. Costs for construction of control measures have been developed and include backfilling strip mines, sealing subsidence areas, reconstructing stream channels, and installing mine seals to prevent the entrance of water and air.

Jan 1, 1973