Search Documents

By Maynard H. Jameson

EARLIER investigations of the potential-drop-ratio method of electrical prospecting have indicated that under suitable conditions this method is well adapted to the location of formation boundaries in stratified ground. A description of this development was given several years ago by H. Lundberg and Th. Zuschlag.1 The curves published by these authors for the potential-drop-ratio variation above a horizontal contact indicated a definite relation of the position of the curve peak to the depth of the interface. The theory underlying this relation was subsequently studied by Z. Mitera in greater detail,2 and the theoretical deductions were compared with the results of tank experiments. The investigations available at this writing were confined to studies of horizontal formation boundaries. It is the purpose of this paper to extend the scope of the previous work to the problem of dipping layers. THEORY Consider the case of three media of different resistivities, whose interfaces are not parallel. If a point-source is located in one of these interfaces, its images do not lie in a straight line, but on the circumference of a circle whose center is at the hypothetical junction of the interfaces. R. F. Aldredge3 determined the relation that exists between the degrees of dip of the two interfaces and the distances between the various images and the point for which the potential is to be found. As seen in Fig. I, three media of resistivities po, pi, and p2 are involved, and the source I is located at the interface of the media (po) and (pi). The perpendicular depth of the lower interface is h,? is the dip, R is the distance between source I and potential point P, and r is the distance between the images and that point. To distinguish between images lying above the ground interface and those below, the notation "odd" and "even" images will be employed; images below the ground interface will be termed "odd" and those above "even." The following relations govern the distances between either kind of images and the potential point: [ ] As previously pointed out, the images of the source are on the circumference of a circle. If the angle of dip is ?, the angle measured from the horizontal to the first image is 2? to the second image it is 4?,, and so on. Since the limit of the reflecting interface is at its outcrop, the last possible

Jan 1, 1941

By H. F. Moore

AT PRESENT, I am connected with an investigation of the so-called fatigue of metals under stress. So far we have studied the more fundamental and simple case of the repeated stress, without the additional complexity of impact, which might bring in other factors. We feel that this investigation, which has been in active progress for a little over a year, has shown more conclusively than has been shown before that steel under repeated applications of stress, reversed from positive to negative, will not fail below some fairly clearly defined limiting stress that,, so far we can see, does not bear any definite relation to the ordinary elastic limit, being as large as the elastic limit in some cases and about one-half the elastic limit in others. I might be asked, first, what is fatigue. The old view is summed up "in the word "crystallization." The idea was that under repeated stress the material changed its crystalline structure. I do not know of any evidence in favor of the theory that metals materially change their crystalline structure under repeated stress. The crystals are broken under repeated stress. The second theory, advanced by Bauschinger, the German scientist, is that under repeated stress some inherent property of the material changes its elastic limit; it is an inherent property of the material, possibly some property of the amorphous cement between the crystal. The third view is that all fatigue of metals is the result of the spread of damage from little localized overstresses. I do not feel justified in stating my positive belief in the third view as against the second, but I have yet to run across a case of failure of steel or other metal, either in the laboratory or in service, that could not be explained by the gradual spread of damage from some nucleus. We have found, for example, that it is possible to subject a homogeneous steel, like Armco iron or a 0.90 per cent. carbon steel, that hag been thoroughly annealed, to one hundred million reversals f stress as high as the elastic limit of the steel with no sign of failure. We stopped the test at one hundred million because the machines Were required for other work. Forty-five days, continuous running at 1500 revolutions a minute is required to produce one hundred million repetitions. On the other hand, a complex structured steel, like a chrome-nickel steel that

Jan 6, 1921

By A. Yoshikawa, T. Sugeno

To detenmine the origin of the sharp fatigue limit in many ferrous metals, S-N curvces were determined in push-pull fatigue at 18.6 kc per sec at room temperature and - 67°C for various kinds of iron. These differed in carbon and nitrogen content and grain size (25 and 2500 grains per sq mm). Sharp knees appeared in the S-N curves of fine-grained specimens with high interstitial content at both temperatures. In coarse-gruined specimens, knees were not sharp .regardless of the interstitial content and the testing temperature. It is concluded from these results that the controlling factov for the appeavance of the sharp fatigue limit is not strain aging but grain size. It has already been mentioned that iron and some iron alloys show fatigue curves characterized by a more or less sharp knee and a fatigue limit.' Explanations of the origin of this characteristic behavior of fatigue in iron appear to fall into two broad classes. One is concerned with interstitial impurities through the aging or locking effect and the other is based on intrinsic plastic properties of iron. Levy and sinclair2 and Lipsit and Horne3 have suggested that the fatigue limit observed generally in iron and steel is due to interstitial solute aging during the course of fatigue. On the other hand, Thompson and wadsworthl have suggested that the fatigue limit may be analogous to the sharp yield point, in the sense that alternating stresses above the fatigue limit are necessary to break down the dislocation locking. However, there are some experimental results which cast doubt on the general validity of these suppositions.4-8 Ferro and Montalenti' have recently suggested that the typical form of the fatigue curve of iron seems to come from an intrinsic plastic characteristic of the iron structure. This suggestion is based on the experimental result that pure iron containing an insufficient amount of interstitial solute to alldw appreciable strain-aging effects still showed a fatigue limit at room temperature. Although systematic investigations on the effect of grain size are scarce, it is thought that this effect is important in relation to the sharp fatigue limit. In fact, sensible differences were observed by Oates and Wilson4 in fatigue behaviors of a low-carbon steel depending on grain size. Ideally, the fatigue limit will be defined as the upper limit of stress amplitudes at which the life is infinite. This ideal fatigue limit can never be determined because of the limited time available for experiments, and moreover scattered data points often leave the construction of S-N curves somewhat arbitrary. And, it is usually stated that a material has a fatigue limit when its statistical S-N curve becomes apparently parallel to the N axis with a more or less sharp knee. The meaning of the fatigue limit and the sharp knee will be discussed in detail in relation to the construction of S-N curves. The origin of this sharp knee was investigated by determining S-N curves of iron for various interstitial contents, testing temperatures, and grain sizes. EXPERTMENTAL PROCEDURE The material as received was a commercial-grade low-carbon steel in the form of 4-mm-diameter rods with the following composition in weight percent: C, 0.09; Si, 0.017; Mn, 0.43; P, 0.006; S, 0.012; Cu, 0.11. Five different groups of specimens were tested. The grain sizes and interstitial contents in each group are given in Table I. The specimens of group C-02 were decarburized by annealing for 100 hr at 700°C, followed by an additional 100 hr at 850°C in wet hydrogen. Specimens of groups N-2 and N-9 nitrided in a mixed atmosphere of ammonia and hydrogen after an initial treatment identical to group C-02. The specimens of group C-9 were prepared in a manner similar to those of group C-02, except heat treatment was carried out in a vacuum. After polishing their surface with emery paper, the specimens of all groups were given a final anneal for 30 min at 930°C and air-cooled in an evacuated quartz tube. For group C*-9 this

Jan 1, 1965

By J. W. Matousek, C. S. Samis

me thermodynamic properties of the components in the Cu-Ni-S ternary system have been studied by measuring the H2S/H2 ratios in a gas phase equilibrated with the molten matte at 1200°C. The measured sulficr potentials have been extended by extrapolation and combtned with previously published data to permit the thermodynamic analysis of the ternary system by integration techniques. A simplifying assumption of ideality in the Ni3Sz-CuS pseudobinary has been made. SINCE copper and nickel metals were first extracted from their sulfide ores the interaction between the two metals and sulfur has been of industrial and theoretical interest. The processes developed to extract copper and nickel have been reported periodically in the literature. The theoretical studies on the Cu-Ni-S ternary have been restricted to problems directly associated with production. It is only within recent years that the binary systems related to this ternary have been analyzed thermodynamically and mathematical devices developed to permit a corresponding treatment of the ternary system. In 1910 an investigation of the role of nickel in Cu-Ni-Fe-S mattes was reported,' It was concluded from this work that nickel is not an element replacing iron in mattes, but rather that Cu-Ni alloys behave as a single metal during the matte converting operation. The laws which govern the converting of Cu-Ni alloys were found to be the same laws as those that govern the conventional converting of copper alone. Although considerable information has been reported on the theoretical aspects of copper smelting, little data is available on the smelting of Cu-Ni ores except for phase diagrams and process descriptions. The available information on the Cu-Fe-S ternary and related systems prior to 1953 has been summarized by Ruddle.2 Since Ruddle's publication, Rosenqvist and coworkers have completed phase equilibria investigations of the Fe-S, Co-S, and Ni-S binaries,3 the Fe-S-O ternary,4 and the Cu-Fe-S-O quaternary.4 An extensive investigation of the Cu-Fe-S ternary system at smelting temperatures has been made by Krivsky and Schuhmann.5 At these temperatures, the Cu-Fe-S system is very similar to the Cu-Ni-S ternary with respect to the location of the single-phase and two-phase liquid matte regions. In the former, however, the area of immiscibility is more extensive and the region of liquid matte-liquid metal-solid metal equilibria is much more extensive. Krivsky and Schumann observed that the Cu2S-FeS pseudobinary system is, for practical purposes, an ideal mixture. This investigation has served as a valuable guide in analyzing the Cu-Ni-S ternary. EXPERIMENTAL The experimental procedure employed in this investigation was the conventional technique of equilibration of the sulfide matte with gaseous mixtures of hydrogen and hydrogen sulfide at 1200°C. The thermodynamic properties of sulfur (S2) in the gas phase are determined by means of Eq. [I] and the activity of sulfur in the matte by Eq. [2].

Jan 1, 1963

Jan 10, 1951

By P. Bardzil, J. Gurland

An experimental study of the variation of transverse-rupture strength with composition Anexperimentaland grain studysize has shown that the strength reaches a maximum for values of the mean free path between carbide particles of 0.3 to 0.6 microns. The fracture oforiginates in and proceeds through the carbide grains mainly. Impact strength and hardness also were recorded. MOST of the physical properties of sintered carbides vary linearly with composition. The transverse-rupture strength, however, shows a unique behavior. As the amount of binder metal is varied from 6 to 25 pct by weight, the strength at first increases; then, between 15 and 20 pct Co, it reaches a maximum of nearly 400,000 psi, and finally decreases with further additions of binder metal. This behavior of the transverse-rupture strength has been reported, among others, by Englel and Sandford and Trent.' The significance of these observations has not been discussed in the literature. That it may be of more than specific importance is indicated by the very similar variation of strength with composition encountered in other systems sintered in the presence of a liquid phase, such as Tic-Ni3 and Fe-Cu.' Experimental Details All compacts were prepared and sintered according to normal industrial practice. The average diameter of WC grains and the mean free path between grains were measured on metallographically prepared samples by a method of linear and planar analysis sing the relations where d is the average diameter of dispersed grains; Nl is the number of noncontiguous grains intersected on a metallographic plane by a line of unit length; N, is the number of noncontiguous grains per unit area; P is the mean free path between grains of dispersed phase; and f is the volume fraction of dispersed phase. Approximately 1000 grains were counted on each sample. For each composition d2 was plotted against P, the resulting straight lines serving as a check on the measurements. The distribution curves of the WC powders of different average diameters were homologous, and no attempt was made to influence the grain size by blending powders, adjusting the sintering conditions, or otherwise altering the particle size distribution. Densities were measured by differential weighings in air and water. The degree of densification did not vary consistently with either composition or grain size. The density is influenced by slight amounts of impurities, specifically by 0.1 to 0.2 pct Fe which enters the powders during ball milling. As an illus- -tration of the experimental variations, a number of measured densities are listed in Table I. They are expressed in percentage of theoretical density, as calculated from the published X-ray densities of WC and Co.' For the purpose of determining the transverse-rupture strength, rectangular test specimens (3/16x 3/8x3/4 in.) were broken by loading at the center of a 9/16 in. span. The average strength of five or more samples is reported for each composition and grain size. The compacts were ground on two parallel surfaces only. The load was applied at an average rate of 6,800 psi per sec. Since the elongation after fracture of the alloys is very small, it was assumed that the compacts deform elastically to failure and the fracture stress was calculated by the conventional beam formula. The data for one alloy are presented in Table II as an example of the results and scattering ranges encountered. The precision of the test, as measured by the average difference between duplicates, is of the order of 15,000 psi. The results are strictly comparable only to compacts prepared and tested in the manner described and of similar chemical composition and grain size characteristics. Unnotched Charpy specimens were used for impact testing. Each point represents the average of 3 to 20 samples, the larger number being used in an attempt to determine the influence of grain size. Considerable scatter was encountered, the range from lowest to highest value often amounting to 30 pct of the impact strength. The hardness is reported as a Ra reading, using a 60 kg load with diamond brale indenter. Compositions are given in weight percent.

Jan 1, 1956

By R. S. Bradley

WHAT are known as insulating firebrick are lightweight firebrick with low thermal conductivity designed primarily for use in direct contact with furnace gases. These are a recent development in the refractories industry, and are really an outgrowth of the type of insulating brick suitable for use behind refractory walls developed by the insulation manufacturers. To differentiate between these two types of brick, the manufacturers have recently agreed upon the use of the term "Insulating Firebrick" to apply to the type of brick suited for use in direct contact with furnace gases, and the term "Insulating Brick" for the type suitable for use behind refractory walls. Insulation was applied to steam pipes as far back as 1900. This was a low-temperature insulation, the most common type being magnesia blocks. The next development was applying insulation to the outside of furnace walls, a service which necessitated an insulating material of higher temperature resistance. Natural diatomaceous earth, both in the powdered and brick form, was used; this was efficient and is still used extensively for backing up refractory walls where the inner surface temperature of the insulation does not exceed 1600° F.

Jan 1, 1937

PRESIDENT E DEGOLYER, District 0 NEW YORK, N Y PAST PRESIDENTS J V. W. REYNDERS, District 0 NEW YORK, N Y SAMUEL A TAYLOR, District 3 PITTSBURGH, PA FIRST VICE-PRESIDENT GEORGE OTIS SMITH, District 4 WASHINGTON, D C TREASURER CHARLES F. RAND NEW YORK, N Y SECRETARY H. FOSTER BAIN NEW YORK, N Y

Jan 1, 1923

By J. P. Heller, H. B. Bradley, A. S. Odeh

A potentiometric model technique is presented for determining the areal sweep efficiency of a five-spot well pattern, at and beyond breakthrough. A sharp interface between displaced and displacing fluids is assumed. Although the prototype svstem is referred to as a waterflood operation, obvious changes in the notation and computations will adapt the results to other displacement processes. The results of the study include the following. 1. Areal sweep efficiencies for a five-spot well pattern, at and beyond breakthrough, for mobility ratios (displacing to displaced fluid) of 4:1, 2:1, 1:1 and 1:4. 2. Extension of potentiometric analysis to the investigation of the areal sweep efficiency beyond breakthrough in a five-spot pattern by the application of conformal mapping and conductive-solid models. 3. The use of layers of conductive fabric in representing mobility ratio changes in potentiometric models. 4. The development of a probe mechanism for probing conductive solids. The results obtained by conductive-cloth models agree with earlier areal sweep efficiencies at breakthrough obtained by Aronofsky and Ramey 1 on the potentiometric analyzer using electrolytic-tank models. Results beyond breakthrough differ from those obtained by the X-Ray Shadowgraph technique. Data from this study show that, for mobility ratios greater than one, water cut rises rapidly as fluid is produced after breakthrough. However, for mobility ratios smaller than one, a large increase in area swept resulted with only a small increase in water cut. INTRODUCTION In calculating reservoir performance of waterflood-ing operations and other fluid-injection programs, it is necesssary to estimate the areal sweep efficiency * before and after injected-fluid breakthrough into production wells. Influence of mobility ratio on oil-production history, before and after breakthrough for a five-spot well pattern, has been studied by X-Ray Shadowgraph techniques 2-5 and by gelatin models.6 In none of these investigations was the transition zone controlled experimentally. Steady-state anaiog techniques assume that a vertical and discrete interface exists between the displacing and displaced phase. Thus, when using a potentiometric analysis, it is assumed that no transition zone exists. To determine the areal sweep efficiency beyond breakthrough for a five-spot well pattern using the potentiometric analyzer, four principal problems had to be resolved. These were the following. 1. The laborious method of representing changes in mobility ratio in electrolytic tanks by means of contoured wooden blocks. 2. Vapcrization of the electrolyte solution during the study causing concentration changes and, thereby, variable conductivity. 3. The scale-limitation problem 7 that is accentuated by abrupt eiectrolyte depth changes. 4. A wellbore geometry problem. EXPERIhlENTAL EQUIPMENT AND PROCEDURES CONDUCTIVE-SOLID MODEL The theory, equipment and procedural techniques of the electrolytic-tank potentiometric model have been treaced excellently by Lee8 and by Muskat.9 By the use of a conductive solid to represent the fluid conductivity of the porous media, the need for contouring wooden blocks to represent mobility ratio was eliminated. It was found that a carbon-black coated fabric, Uskon D-16,** could be employed as a fairly uniform conductive media. This material, when stacked in appropriate layers and pressed together, can be used to represent changes in mo-

By C. DeWitt Smith

"It just looks like everything is doing fine but humans," wrote Will Rogers fifty years ago. "Animals are having a great year, grass was never higher, flowers were never more in bloom, trees are throwing out an abundance of shade for us to loaf under. Everything the Lord has a hand in is going great, but the minute you notice anything that is in any way under the supervision of man, why, it's cockeyed." Do these words from two generations ago apply to oil shale? The United States has been blessed with deposits that can yield synthetic crude oil at a cost competitive with natural crude oil-under present economic conditions and with existing technology. Yet, the oil shale program is cockeyed because of the artificial obstacles that have been placed in its path "under the supervision of man." But more about this later. For the moment, let's focus on...

Jan 10, 1974

By T. M. Dr. Drown

(Read at the Philadelphia Meeting, February, 1878.) ZINC is, as is well known, very brittle at a temperature of about 210° C. (410° F.), and may then be readily pulverized in a mortar. By sifting it may be obtained of uniform grain. I have been accustomed to prepare products passing through 40, 60, and 80-mesh sieves, and also by bolting through a fine handkerchief. The principal analytical uses to which I have hitherto applied this material are to the reduction of iron directly from the ore by heating it with the pulverized zinc, and the reduction of ferric to ferrous compounds in solution. In the first case the pulverized ore, 0.5 gram or less, is intimately mixed with about ten times its weight of the pulverized zinc (the finer the zinc the better), in a porcelain crucible, and this mixture is covered with about the same amount of zinc. The crucible is then heated at the top of the flame of a Bunsen burner, at a dull red heat, for about ten minutes. The crucible should not be covered. When cool, the crucible, with its contents, is placed in a flask treated with hot dilute sulphuric acid, and brought quickly to a boil. The zinc and reduced iron are dissolved in a few minutes and the flask is then tightly corked and allowed to cool. When cool, the iron is directly titrated by potassium permanganate.

Jan 1, 1878

H. McD. Lorain says in regard to his son, Captain S. H. Lorain; "It might be of interest to you to know that, although but 23 years of age, my son is captain of Co. C 107th U. S. Engineers, Thirty-second Division. He landed in France about the middle of February, 1918, and was commissioned a captain on Sept. 5, 1918. He started for the front the latter part of June and was there continuously until the armi-stice was signed, on Nov. 11, being on the front lines in the Argonne at that time. He is, at present, in Coblenz, Germany, with the Army of Occupation. Although much of his work was clone under artillery and machine-blur fire, as well as airplane bombs and fire, he escaped without a scratch. Once, he was the only one of a group who escaped without a scratch from an exploding shell." Lieut. Bernard H. Lasky, on a post card received a short time ago, gave the following brief record of his military career. "I have been serving with the 316th Engineers in France and in Flanders and had the satisfaction of being in the last big drive in Belgium which sent the enemy beyond Avaenarde and did much to increase their gait on their way to Brussels. On Oct. 1, I received a commission as second lieutenant and was assigned to Co. C of the 316th Engineers."

Jan 3, 1919

By Spencer Cragoe

I have read with much interest the elaborate and able paper of Messrs. Granger and Treville on the Mining Districts of Colombia, presented at the Atlantic City Meeting (ante, p. 33). Going into detail, however, as the paper does—and particularly with reference to the department of Antioquia, I am somewhat surprised that the property of the Frontino and Bolivia Company, probably one of the richest and most extensive in Colombia, should come off with such scant notice. The entire property embraces an area of some 28 square miles, and is situated at a distance of about 2 leagues from Remedios—after Medellin probably the most important town of the Department—and lying in approximately '7° N. latitude. The neighborhood of Remedios has been long celebrated for its production of the precious metal. Alluvial gold in large quantities has been obtained from the vicinity for upwards of two centuries; and even to-day a large proportion of the population finds a comfortable livelihood, during the dry season, in washing the sands of various rivers, notably the Rio Porce; while the amount of gold, in the form of nuggets, brought almost daily to Remedios and other points, from streams in the immediate neighborhood, is astonishing. These nuggets vary much in size. The majority, of course, are small, but larger ones are by no means scarce. I have been considerably surprised at the amount and value of the trade thus transacted between natives and merchants of the various towns. The property owned by the Frontino and Bolivia Company has been, I believe, for the larger part of the present century,

Jan 1, 1899

THE CHAIRMAN (EDWIN LUDLOW, Lansford; Pa.).-Mr. Wang's paper reminded me that some years ago I was asked if I would not go into the Tien Tsin district and take charge of Americanizing a Chinese mine. They said the trouble was that, while wages were only 9 c. a day, the coke cost $2 a ton delivered to the cars. Reading Mr: Wang's paper would indicate the need of a little Americanization in the Manchurian field. Wages are only 40 c: a day, yet the cost is $3.60 a ton. An efficiency engineer would have an excellent opportunity in that field. T. T. READ, New York, N. Y.-It is always true that low-priced labor is inefficient, wherever we find it; for example, in Japan, where wages are low, but not so low as in Manchuria, working costs are not relatively much lower than ours. Mr. Padshah, describing his experience in India, once told me that, while wages were only about one-fifth as high

Jan 4, 1918

By D. E. Wolfson, H. J. Gluskoter, M. R. Geer, John A. Harrison, H. F. Yancey, I. S. Latimer

When this chapter was prepared for the kst edition in 1942, continuous mining machines virtually were unknown, and hand loading in underground mines, which gave an opportunity to discard impurities, accounted for 55 percent of the production of bituminous coal and lignite as compared with the 1965 figure of 11 percent. Only 24 percent of the total production was cleaned mechanically, compared with the present (1965) figure of 65 percent. The amount of refuse discarded during preparation for the same period increased from 13 to 21 percent. Changes in the equipment used in the cleaning process were as follows: [ ] Unclassified nearly 8 percent. Data on the amount cleaned by flotation was not collected until 1960 when 1.8 million net tons was so treated. In 1965 this figure increased to 6.9 million tons. Although the great increase in mechanization and full seam mining has resulted in substantial increases in the impurity content of the raw coal as well as in a finer size consist, some phases of face preparation are still important, particularly the variability of the distribution and thickness of the interbedded impurities and the changes in the character of the roof and floor from place to place in the mine. Knowledge of these factors in relation to all phases of the mining operation, particularly selective mining, are still of importance to the treatment of raw coal in the preparation plant. The major characteristics of coal and impurities from the standpoint of mechanical cleaning are particle size composition, generally called size consist, density differences, the relative friability of the coal and of its associated impurities, hardness, and strength. Some of the other factors related to preparation are petrographic composition and rank. COAL PROPERTIES Rank Perhaps 95 percent or more of the coal cleaned mechanically is of bituminous rank. Only a very small tonnage is subbituminous and prac-

Jan 1, 1968

By R. J. Sherman, M. R. Achter

IT has often been reported that coatings may strengthen single crystals and polycrystalline specimens of coarse grain size. This note reports the effect of a surface layer of fine grains on the creep-rupture properties of coarse grained nickel 99.8 pct pure. Sheet specimens were machined from cold-rolled material, finished by surface grinding and annealed at 1230°C in vacuum for 4 hr. Half of them were re-ground on faces and sides and annealed at 925"C for 1 1/4 hr. The double grind-anneal treatment produced a structure consisting of a surface layer of fine grains of 0.02 mm diam on a coarse-grained substrate of grains of 0.40 mm diam. Comparison with specimens which received only the single grind showed that the second grind-anneal did not alter the structure of the substrate. Several modifications were made in specimen design to eliminate erratic rupture behavior outside of the gage length. In the final design the gage section, oriented parallel to the rolling direction, was 1.00 in. long, 0.4 in. wide, and 0.0625 in. thick. End tabs were pinned in place. Although other configurations (welded end tabs, transverse orientation, and wider gage section) showed similar effects of a layer of fine grains, because of the erratic rupture behavior, only the data from the final design are reported here. Creep tests were performed at 650°C in air and in a vacuum of 10~5 mm Hg. Creep rates were measured from the movements of the lever arm. Since the broken sheet specimens could not be fitted together, elongations at fracture measured by means of gage marks, do not include the necked portions adjacent to the fracture. Results of the creep tests with and without the fine grained surface are given in Table I. An explanation for the lower strength in air than in vacuum has been proposed previously in terms of the reduction of crack propagation energy by gas adsorption.l In both environments the fine-grained layer produced a small decrease in minimum creep rate and, except for the shortest test in air, a substantial increase in rupture life. The elongation values at rupture, as they are measured here, do not demonstrate an appreciable effect of the grain structure but do show much smaller ductilities in air than in vacuum. Greater elongations maybe associated with the finegrained layer, however, especially in vacuum, in creep curves such as those in Fig. 1. Duplicate tests were not run to determine the re-producibility of the data. It is felt, however, that, in view of the consistent behavior, the prolongation of rupture life may be attributed to the effect of the fine-grained surface. In the data not reported be-

Jan 1, 1962

By J. S. Miller

This paper describes the method of mining a steeply pitching anthracite seam on a heavy pitch in the Orchard vein in No. 1 Tunnel of the Lehigh Coal and Navigation Co. The Orchard vein in the Neaquehoning district has a thickness of about 15 ft. on the level of the gangway, which is sufficient thickness for the gangway to be driven full width in coal. Above the gangway, the vein becomes thinner and near the surface is about 8 it. thick. The coal is of good hard quality and carries a fairly good roof. The pitch of the vein is between 65" and 70". Usually the breast-and-pillar method has been employed in the mining of the steeply pitching veins in this section. This method produced good results as far as the mining of the breast was concerned but the recovery of the pillar was difficult as to full extraction and expensive as regards costs. To recover these pillars after the breasts were driven, three methods were commonly employed; they were known as the pillar-breast method, pillar-skipping method, and pillar-chute method. The pillar-breast method consisted in putting a battery in one corner of the pillar (Fig. I), coupling the manways A and B of the two adjacent breasts for two or three lengths ahead of the working face of the pillar being cut, and working the pillar as a breast. This method was used by the more skilled miners of the earlier days but has practically been abandoned. A slight variation of this method is used to some extent. In this case, the pillars are left wider than ordinarily and of sufficient width for the full-width breast to be driven in and a small pillar left on each side of the pillar breast between it and the regular breasts. With the completion of the "pillar breast," the ribs are drilled full of holes, loaded, and fired. In the pillar-skipping method (Fig. 2), the middle breast of three is not driven through and is drawn empty while the outside and inside breasts are kept full. At the corners of the two pillars standing, batteries are put in and a skip of the two pillars started; the coal in the two pillars is blasted over into the empty breast. A small pillar is kept along the

Jan 1, 1925

By S. Lipson, H. W. Antes, H. Rosenthal

A study was made of the effect of ingot structure on the strength and ductility of high-strength wrought-aluminum alloys. It was found that a fine-cast structure facilitated complete homogenization which, in turn, resulted in significant increases in ductility and strength. A completely homogenized 7075-T6 alloy developed tensile properties of 85,000 psi UTS, 75,000 psi YS, with 40 pct RA. Completely homogenized 7001-T6 alloy tensile properties were 102,000 psi UTS, 99,000 psi YS, with 19 pct Ra. A method was devised for making small ingots having secondary dendrite arm spacing of less than 10 u. This method involved multiple-pass arc melting of commercial rolled plate with a tungsten electvode. This material could be completely homogenized after 3 hr at 900°F; homogenization of the original plate material was not complete after 120 hv at 900°F. Degree of homogeneity was determined by use of metallographic and electron-microprobe analyses. The electron-micro-probe study also showed the preferential segregation of solutes in the microstructure. HIGH-strength aluminum alloys, such as those of the 7000 series, usually freeze by the formation and growth of dendrites. The dendrite arm spacing (DAS) depends on the rate of solidification.' Commercial ingots are usually direct chill-cast to promote more rapid solidification, but, due to the large mass of the ingot, localized solidification times are long and a large DAS results. During solidification, solute elements are rejected by the solid as it forms, causing enrichment of the liquid and ultimately solute-rich interdendritic regions. In order to attain a homogeneous ingot, the segregated solutes must diffuse across the dendrite arms. The larger the DM, the longer the time for complete homogenization. In the case of commercial ingots, the DAS is so large that the time for complete homogenization is prohibitively long and, therefore, second phases or compounds are always present. These un-dissolved phases are carried over to the wrought material during processing, resulting in an impairment of strength and ductility. In addition, the mechanical fibering of the undissolved second phases or compounds during working results in mechanical property anisotropy. If complete homogenization could be attained, higher ductility could be expected. The realization of higher ductility at current strength levels is a desirable objective; however, if higher-strength alloys were wanted, it might be possible to sacrifice some of this ductility by adding more solute elements and produce even higher-strength alloys than are currently available. Further, if complete homogenization leads to more efficient utilization of solute elements, then more dilute alloys should have relatively high strengths with very high ductility. In all instances, it would be expected that the degree of mechanical property anisotropy due to mechanical fibering would be reduced. Therefore, it was the purpose of this investigation to produce cast structures that would facilitate homogenization and to determine the effect of homogenization on the properties of high-strength, wrought-aluminum alloys. MATERIAL CLASSIFICATION Commercial Alloys. In order to illustrate the non-homogeneous condition that exists in commercial high-strength, wrought-aluminum alloys, typical micro-structures of 7001, 7075, and 7178 are shown in Fig. 1. The chemical compositional specifications of these alloys are given in Table I. It can be seen in Fig. 1 that a considerable amount of undissolved second-phase material is present in each of these alloys. The solute elements associated with the undissolved phases were identified by electron microanalyses. Back-scattered electron images and characteristic X-ray images of the three commercial alloys are shown in Figs. 2, 3, and 4. These data indicate that the second phases are regions of high copper and high iron-copper concentrations. The second-phase material also was analyzed for magnesium, zinc, manganese, chromium, and silicon, but no significant enrichment above that of the matrix was found. Therefore, the problem of homogenization resolved itself into one of dissolving the copper-rich and the iron-copper-rich second phases. In order to accomplish this objective, two approaches were made. The first was to reduce the iron as low as possible since this element has a maximum solid solubility of 0.03 pct in aluminum. The second was to produce cast structures with finer DAS to facilitate dissolving the second phases. Commercially Produced High-Purity Alloys. A special high-purity, 2000-lb ingot of 7075 alloy was made by a commercial producer. This alloy contained the following weight percentages of solutes: 5.63 Zn, 2.48 Mg, 1.49 Cu, and 0.21 Cr. All other elements combined were less than 0.02 pct by wt including iron and silicon at less than 0.01 pct each. The ingot was cast and processed into rolled plate using standard commercial techniques. Microstructures of standard commercial 7075 and the special high-purity 7075 are shown in Fig. 5. It can be seen from this figure that the high-purity alloy has less undissolved second-phase material, but a significant amount was still present. The second phase in the high-purity material did not contain iron but it was found to be enriched with copper. The slight effects of the increased purity and de-

Jan 1, 1968

By William D. Klopp, Joseph R. Stephens

A substantial reduction in the 300°F ductile-to-brittle transition temperature for unalloyed chromium was achieved in alloys from systems which resemble the Cr-Re system. These alloy systems include Cr-Ru, Cr-Co, and Cr-Fe. Transition temperatures ranged from -300° F for Cr-35 at. pct Re to -75°F for 0-50 at. pct Fe. The ductile alloys have high grain gvowth rates at elevated temperatures. Also, Cr-24 at. pct Ru exhibited enhanced tensile ductility at elevated temperatures, characteristic of superplas-ticity. It is concluded that phase relations play an importarlt role in the rhenium ductilizing effect. The ductile alloys have compositions near the solubility limit in systems with a high terminal solubility and which contain an intermediate o phase. The importance of enhanced high-temperature ductility to the rhenium ductilizing effect is not well understood although both may have common basic features. CHROMIUM alloys are currently being investigated for advanced air-breathing engine applications, primarily as turbine buckets and/or stator vanes. The inherent advantages of chromium as a high-temperature structural material are well-known1 and include its high melting point relative to superalloys, moderately high modulus of elasticity, low density, good thermal shock resistance, and superior oxidation resistance as compared to the other refractory metals. Additionally, it is capable of being strengthened by conventional alloying techniques. The major disadvantage of chromium is its poor ductility at ambient temperatures, a problem which it shares with the other two Group VI-A metals, molybdenum and tungsten. For chromium, the problem is further amplified by its susceptibility to nitrogen em-brittlement during high-temperature air exposure. In cases of severe nitrogen embrittlement, the ductile-to-brittle transition temperature might exceed the steady-state operating temperature of the component. The low ductility of chromium would make stator vanes and turbine buckets prone to foreign object damage. The present work was directed towards improvement of the ductility of chromium through alloying, with the anticipation that any improvements so obtained might be additive to strengthening improvements achieved through different types of alloying. The alloying additions for ductility were selected on the basis of the similarity of their phase relations with chromium to that of Cr-Re. The reduction in the ductile-to-brittle transition temperatures of the Group VI-A metals as a result of alloying with 25 to 35 pct Re is well established.a4 the temperature range -300" to 750° F. This phenomenon is commonly referred to as the &apos;<rhenium ductilizing effect"; this term is also used to describe systems in which the ductilizing element is not rhenium. Other alloy systems which have recently been shown to exhibit the rhenium ductilizing effect include Cr-Co and c-Ru.= In order to explore the generality of this effect, alloys were selected from systems having phase relations similar to that of Cr-Re, primarily a high solubility in chromium and an intermediate o phase. The following compositions were prepared: Cr-35 and -40Re; Cr-10, -15, -18, -21, -24, and -27 pct Ru; Cr-25 and -30 pct Co; Cr-30, -40, and -50 pct Fe; Cr-45, -55, and -65 pct Mn. Seven other systems were also studied which partially resemble Cr-Re. These systems have extensive chromium solid solutions or a complex intermediate phase, not necessarily o. The compositions evaluated include the following: Cr-20 pct Ti; Cr-15, -30, and -45 pct V; Cr-2.5 pct Cb; Cr-2.5 pct Ta; Cr-20 pct Ni; Cr-6, -9, -12, and -15 pct 0s; Cr-10 pct Ir. The compositions of alloys in these systems were chosen near the solubility limit for the chromium-base solid solutions, since in the Group VI-A Re systems, the saturated alloys are the most ductile. These alloys were evaluated on the basis of hardness, fabricability, and ductile-to-brittle transition temperatures. In addition to the studies of alloying effects on ductility, an exploratory investigation was conducted on mechanical properties at high temperatures in Cr-Ru alloys EXPERIMENTAL PROCEDURE High-purity chromium prepared by the iodide deposition process was employed for all studies. An analysis of this chromium is given in Table I. Alloying elements were obtained in the following forms: Commercially pure powder — iridium, osmium, rhenium, and ruthenium. Arc-melted ingot — titanium and vanadium. Electrolytic flake — iron, manganese, and nickel. Sheet rolled from electron-bearn-melted ingot — columbium and tantalum. Electron-beam-melted ingot — cobalt. Sheet rolled from arc-melted ingot — rhenium. All alloys were initially consolidated by triple arc melting into 60-g button ingots on a water-cooled hearth using a nonconsumable tungsten electrode. The melting atmosphere was Ti-gettered Ar at a pressure of 20 torr. The ingots were drop cast into rectangular slabs and fabricated by heating at 1470" to 2800° F in argon followed by rolling in air. Bend specimens measuring 0.3 by 0.9 in. were cut from the 0.035-in. sheet parallel to the rolling direction. The specimens were annealed for 1 hr in argon, furnace cooled or water quenched, and electropolished prior to testing. Three-point loading bend tests were conducted at a crosshead speed of l-in. per min over

Jan 1, 1969

By T. T. Chen, P. Pint

Based on the mineralogy, phase characteristics and compositions of the smelter feed, the smelter products and the smelter wastes, the sources and distributions of mercury and arsenic in the Afton copper smelter, Kamloops, British Columbia have been determined. Of the total mercury In the feed, approximately 33% is in solid solution in tennantite, 51% is in native copper and 16% occurs as mercurian silver. Arsenic in the feed occurs mainly as tennantite. Under current smelting conditions, 99.6% of the total mercury In the feeds enters the off-gas cleaning system. From this off-gas, about 1% of the total mercury, occurring as dust, is recirculated to the flotation concentrate; 4.6% of the total mercury is contained in SO2 scrubber sludge which is discharged to tailings. Approximately 78% of the total arsenic in the smelter reports in the copper products; 20% is incorporated in the dust and slag which are subsequently recirculated to the mill. Only 1.8% is rejected as scrubber sludge, and less than 0.2% 1s released to the mercury scrubber.

Jan 1, 1984