Search Documents

By Keith Sutherland

AEROFLOAT 25 is a complex mixture of free cresylic acid with aryl substituted dithiophosphoric acids, sulphides, disulphides, etc. Its complete composition has not been published by the makers or patentees. It is prepared1 by the reaction between phosphorus pentasulphide and carefully selected cresylic acid. We have been informed that this acid contains no phenol and very little cresol, and that it is rich in the higher alkyl phenols, particularly the xylenols. The reaction between a phenol ROH and phosphorus pentasulphide may produce compounds of the following type:2 (i) RO S P Diaryldithiophosphoric acids RO SH (ii) R-SH Thiophenolic compounds (iii) R-S-R Diaryl sulphides (iv) R-S-S-R Diaryl disulphides (v) Substituted thianthren compounds Except for the simplest type, the thiophenols (ii), the boiling points of these compounds lie above 300° C. The amounts of the thianthren compounds formed from the five xylenols (if all these are present) will vary according to the position of the substituents. In an attempt to ascertain something of the nature of the reagent, fractional distillation under atmospheric pressure was undertaken. At the outset, hydrogen sulphide was freely evolved, and-particularly below 200° C.-the fractions had the strong odor characteristic of the

Jan 1, 1939

By Thomas C. Wilder

ALTHOUGH there is an abundance of thermodynamic information available in the literature today, no experimental data on the standard molar properties of formation of zinc oxide have ever been reported for the temperature range 419.5" to 908°C. This is the temperature range for which zinc metal is a liquid. so that the formation reaction is: Data have been reported for Reaction [I] where zinc is a solid or a gas. Maier. Parks, and nderson' measured the electromotive force of the cell: in order to obtain the free energy of the reaction: over a limited temperature range. With the known properties of H2O, those of ZnO were calculated. These workers found that t;j of ZnO is -75,930 ± 150 cal per gfw and Mtf is-83,000 300 cal per gfw at 25°C. akolkin made similar measurements to obtain ilF7 and AH; of -75,870 and -82,540 cal per dw respectively at the same temperature. Truesdale and arirlg and Kitchener and 1gnatowicz4 measured the equilibrium of the reactions: respectively, in order to determine Ff of ZnO from the known values of CO, CO2, and H/X The thermodynamic properties of ZnO, presumably taken from the above investigations, are tabulated by Kubaschewski and vans' and Wicks and Block" The latter reference also gives values for the range where zinc is a liquid. These numbers are probably acquired from the known extremities of the range plus Cp data of the components. In the present work the electromotive force of the cell: was measured in order to calculate the properties of ZnO from the well known values of NiO for the temperature range where zinc is a liquid. In Cell [B] the cathode reaction is: and at the anode: The overall reaction is: for which the free energy change is: where is the electromotive force in volts of cell [B] after correction for the Pt-Ta thermocouple. The standard molar free energy of formation of NiO is very well known as a function of temperature. Kiukkola and agner's data are used in most tabulations. The error is probably less than I00 cal per gfw, The latter authors were the first to use solid mixed oxide electrolytes in galvanic cells. Their work with NiO and other oxides was performed with cells similar to Cell [B] using a variety of reference electrodes of fixed oxygen potential. There may be a small composition range for which either NiO, ZnO or both exist. If nonstoichiometry does exist for these oxides, then the properties described herein are those for the metal saturated compositions. The simple cell design was the same as described elsewheres except that the molten metal electrode was about 125 g of pure zinc including a small (0.25 to 0.50 g) amount of ZnO. The mixture of pure nickel and NiO powders making up the reference electrode was contained in a tube of the ZrOl + CaO electrolyte which was immersed in the molten zinc. A platinum contact was made to the reference electrode; tantalum to the zinc. A refractory cement plug was necessary at the open end of the electrolyte tube in order to prevent zinc vapor from contaminating the reference electrode. Experimental details such as the vessel containing the cell, furnace, temperature control and measurement, and electromotive force determinations of the cell have all been outlined previously. The temperature was varied randomly in the range between the freezing and boiling points of zinc. After each temperature change, time was allowed for the drift at the new temperature to be less than +;"c whereupon a series of three cell readings was taken at least 10

Jan 1, 1970

J. E. Johnson, Jr., Glen Wilton, Va. (communication to the Secretary*):—Mr. Meissner announces early in his paper that one of its purposes is the discussion of my paper entitled, Notes on the Physical Action of the Blast-Furnace,' with which he disagrees in part; and as the second stage of the discussion of this important subject has centered around his paper, some reply by me may not be amiss. Unfortunately, Mr. Meissner has not indicated a single statement or conclusion in my paper that he wishes to controvert; but as there is evidently a difference of opinion between us I will disregard this fact, and will discuss those conclusions of his that seem to me not to be justified by the facts of general practice, or even by the data which he produces to support them. Let me say, however, that I am a believer in the dry-air

Jan 1, 1908

By Robert L. Voss, Richard D. Hagni

Sparry dolomite from all of the operating mines in the Viburnum Trend of Southeast Missouri have been found by cathodoluminescence microscopy to reveal a systematic pattern of banding resulting from a growth zoning within individual dolomite rhombs. Four principal bands have been recognized throughout the entire Trend and each of the major bands contain even finer internal banding. Minor bands a few microns in width can be correlated in specimens collected ten's of kilometers apart along the trend. The first three principal dolomite bands decrease from south to north. This feature, together with the fact that the white sparry dolomite crystals decrease in abundance from south to north in the Trend, suggests that a major source for the fluids was from the south. The application of cathodoluminescence microscopy to crystalline dolomite demonstrates a strong correlation between ore grade and the intensity of internal banding and dissolution textures.

Jan 1, 1985

By W. E. Keck, W. C. Lowry, G. C. Eggleston

The potential iron ores of Michigan can be classified from the stand-point of the predominant impurities into siliceous, sulphurous and phos-pllorous ores. Research on the flotation of each of these classes of ore was carried out in the following manner. The flotative properties of the valuable minerals of iron and of the worthless and deleterious ones were first determined under carefully controlled conditions. This information was then applied to synthetic mixtures of these minerals, which simulated the potential ores. Finally, data obtained during the two foregoing stages of the investigation were used in the flotation beneficiation of samples of the potential ores. Hematite is the most important mineral of iron in each of the above classes of iron ores. This paper deals with a study of that mineral in the very nearly pure state. There are two varieties of the mineral—specular hematite and massive hematite. The latter is the principal variety, but the former is an impor-tant' mineral of iron in some of the potential ores. Because of this condition, flotation research was performed with both varieties. This research consisted essentially of: (I) a survey of the literature on hematite flotation, (2) the preparation of pure massive hematite, (3) the preparation of pure specular hematite, (4) the development of a laboratory procedure and (5) flotation experimentation. For the purpose of this discussion, the results of previous work on the flotative properties of hematite can be summarized as follows: Specular hematite has been readily floated with terpineol and sodium oleate or heptylic acid1. Further, hematite has been likewise floated with a proprietary frother and oleic acid or other soluble oils2. Finally, lead nitrate, copper sulphate, silver nitrate, chromium nitrate, mercuric chloride, ferric

Jan 1, 1939

By G. C. Eggleston, W. E. Keck, W. C. Lowry

The potential iron ores of Michigan can be classified from the stand-point of the predominant impurities into siliceous, sulphurous and phos-pllorous ores. Research on the flotation of each of these classes of ore was carried out in the following manner. The flotative properties of the valuable minerals of iron and of the worthless and deleterious ones were first determined under carefully controlled conditions. This information was then applied to synthetic mixtures of these minerals, which simulated the potential ores. Finally, data obtained during the two foregoing stages of the investigation were used in the flotation beneficiation of samples of the potential ores. Hematite is the most important mineral of iron in each of the above classes of iron ores. This paper deals with a study of that mineral in the very nearly pure state. There are two varieties of the mineral—specular hematite and massive hematite. The latter is the principal variety, but the former is an impor-tant' mineral of iron in some of the potential ores. Because of this condition, flotation research was performed with both varieties. This research consisted essentially of: (I) a survey of the literature on hematite flotation, (2) the preparation of pure massive hematite, (3) the preparation of pure specular hematite, (4) the development of a laboratory procedure and (5) flotation experimentation. For the purpose of this discussion, the results of previous work on the flotative properties of hematite can be summarized as follows: Specular hematite has been readily floated with terpineol and sodium oleate or heptylic acid1. Further, hematite has been likewise floated with a proprietary frother and oleic acid or other soluble oils2. Finally, lead nitrate, copper sulphate, silver nitrate, chromium nitrate, mercuric chloride, ferric

Jan 1, 1939

CURRENT MATTERS Page Page Colorado Meeting iii. Members in Military Service... xxxvi New York Meeting, Proceedings. iv Personal xxxix War Smoker xi Positions Vacant xli Woman's Auxiliary xxiii Engineers Available xli Meeting of Board of Directors... xxvii Forthcoming Meetings xlii Publication Notes xxviii Library xliii Local Section News: Membership xlvii Colorado xxix Biographical Notices: Montana xxx Arthur B. de Saulles lxxi Puget Sound xxxi James W. Malcolmson lxxii Tulsa xxxii Frank Firmstone lxxiii Affiliated Student Societies xxxii A. Stanley Hill lxxv Eleventh Engineers xxxiii Frederic W. Matthiessen lxxvi Enlistments in Engineer Organ- _ Institute Committees lxxviii izations xxxv Officers and Directors lxxxvi

Jan 4, 1918

Univ of Alabama-University, Alabama-Mining and Metallurgical Society William L Mason, Faculty Sponsor, E C Wright, Dept Head Univ of Alaska-College, Alaska-Mining Society of the Univ of Alaska Douglas W Huber, Faculty Sponsor, E H Beistline, Mining & Metallurgy Dept Head, Troy L Pewe, Geology Dept Head, James Crawford, Chapter Counselor Univ of Arizona-Tucson, Arizona-Miners Society Willard C Lacy, Faculty Sponsor, J D Forrester, Mining & Metallurgy Dept Head, F W Galbraith, Geology Dept Head Univ of California-Berkeley, California-Mineral Technology Association H E Hawkes, Faculty Sponsor, Joseph A Pask, Dept Head

Jan 1, 1959

By F. W. Lee

A GREAT CURTAILMENT of field activities among the geophysicists occurred last year, especially in prospecting for the common metals. In gold, however, an "outstanding achievement . . . was made by the engineers of Consolidated Goldfields. Here the suboutcrop of the Main Reef Series was traced from Middelvlei through properties of the westward area, a distance of from 30 to 40 miles. Here Drs. Reineche and Krahman prospected with the aid of a sensitive magnetometer and established the singularities of the various beds which heretofore had not been sufficiently appreciated. Several underlying shale beds were used to determine this suboutcrop under the dolomite. This area promises to be the equivalent of one-half the size of the present gold fields and to rank in value with the Far East Rand." The present temperature compensated magnetometers permit accurate field observations to less than 5 gammas. Since magnetic anomalies may have their origin due to a change of elevation as well as to the outcropping of a bed of another magnetically different material, intimate geological knowledge is of great assistance in the interpretation of these measurements. To what extent magnetic measurements reflect the basement when the material is homogeneous, consisting primarily of red granite, was determined by members of the Bureau of Mines and described by Dr. J. H. Swartz. Because of the diverse causes of magnetic anomalies, some of which were discussed and correlated by Stratton and Joyce upon known conditions, magnetometer measurements are often difficult to interpret.

Jan 1, 1933

By D. R. George

Preliminary research has identified several organic and aqueous solutions that are effective absorbents for SO, from simulated smelter gas containing 0.3 to 2% SO2. These SO2 loaded solutions are also compatible to the reaction of H2S and SO2 to precipitate a readily filtered elemental sulfur. The economic removal of SO2 and production of elemental sulfur from stack gases discharged by base- metal smelters is a challenging goal. The magnitude of this task is illustrated by the estimate that about 3.5 million tons of SO2 are discharged to the atmosphere by smelters annually in the U.S. The SO2 concentration of the gases ranges from about 0.5 to more than 3%. As the sulfur content of SO2 is 50% a potential production of 1,750,000 tons of sulfur per year is indicated.

Jan 1, 1970

By D. L. Albright, G. A. Colligan

An investigation has been conducted to determine the nature of the crystallographic substructure of nickel and a 1.0 wt pct Ag-Ni alloy which had been undercooled 105°C prior to solidification. A rotating back-reflection X-ray technique and modified Weissmann diffractometer were used to orient single-crystal sections from these poly-crystalline ingots and to determine the substruc-tural features of these single crystals, The sub-grain size in the pure nickel ingot is 0.5 mm diam while the silver-doped nickel subgrain size is only 0.1 mm diam. The misorientation between adjacent subgrains is approximately 1 deg of arc in both ingots, and the spread of orientation of sub-grains about the mean orientation of the crystal is 5 deg of arc in both ingots. The addition of silver results in a stable impurity substructure which is preserved during isothermal solidification and subsequent cooling to room temperature. In the absence of silver the initial impurity substructure is destroyed by dislocation interactions which produce a secondary substructure which grows to a size five times larger than the initial substructure. THE process of undercooling a metal entails cooling of the molten sample below the equilibrium freezing point without the occurrence of solidification, i.e., by exercising proper constraint over the experimental variables contributing to nucleation in the melt. The current work of walker1 and Colligan Metal reports undercooling large continuous samples of nickel by imposing appropriate restrictions upon the parameters of solidification. The silver-nickel equilibrium diagram3 reveals the presence of a monotectic reaction at 1435°C. At this temperature the maximum solid solubility of silver in nickel is approximately 3 wt pct, but this solubility decreases with decreasing temperature and the solute is rejected as a silver-rich liquid phase at temperatures below 1435°C. Thus, the 1.0 wt pct solute should be held in solution during undercooling and solidification and subsequently precipitate as a silver-rich liquid phase at grain and subgrain boundaries following solidification during cooling below 1435. This assumes no solute segregation sufficient to cause the monotectic reaction. One would expect this second phase to inhibit grain and subgrain growth by retarding dislocation motion after solidification is complete. The effectiveness of silver addition in growth retardation of high-angle grain boundaries has been demonstrated by Colligan and suprenantS4 The principal [l00] dendrite growth directions in a 2 wt pct Ag-Ni alloy undercooled 53 all radiated from the nucleation site. A similar pure nickel ingot undercooled 59°C exhibited a random orientation of [l00] dendrite directions with respect to the nucleation site. Since undoped nickel ingots do not retain any evidence of the casting or solidification texture and silver-doped ingots do retain this texture, it is reasonable to assume that considerable grain growth has taken place in the pure nickel. These particular experiments were performed in order to reveal the differences, if any, in the features of the crystallographic substructure of undoped undercooled nickel and silver-doped undercooled nickel. 1) EXPERIMENTAL PROCEDURE Data are reported on selected specimens from two massive (approximately 260 g) undercooled ingots of nickel. One ingot consisted of electrolytic nickel and the other of this same material with 1.0 wt pct addition of high-purity silver. Powder patterns were taken of both the as-received and as-solidified materials; in all cases the reflections recorded were attributable to the individual elements nickel and/or silver. Fig. 1 is a. schematic diagram of the apparatus employed for the undercooling experiments. The equipment consists in part of a fused silica crucible for containing the charge. A fused silica tube encloses the system, which is covered by a brass cap to permit partial sealing of the inert atmosphere. This cap contains a hole through which a Pt-Pt 13 pct Rh thermocouple is inserted for temperature measurement. The charge is inductively heated under a purified argon atmosphere.

Jan 1, 1963

By Geo. T. Lynch

PALEOLITHIC MAN, laboriously shaping a stone implement in his cave, discovered that the dust irritated his eyes and nostrils and hindered his labors, whereupon, muttering a few incantations, forerunners of modern profanity, he removed himself and his work outside. There, ignoring the jeers of the hairy ?old-timers,? he turned his back to the wind and resumed operations in comparative comfort. Thus originated the dust problem in the mineral industries, and its solution. Despite long familiarity with the annoyance, danger, and loss occasioned by dust, little progress was made in the engineering solution of its problems until recent years. Some advance can now be reported but too many traces of ancient tradition and practice still remain. Considerable published information is available but only a part of this is of proved accuracy and utility. The greater portion is either misleading, being derived from too few cases to be of general application, or entirely erroneous, originating in guesswork, legend, or individual inspiration, divine or otherwise. The engineer, confronted with a dust problem, has neither the time nor the special training required to extract the values from this mass of low-grade. It is, therefore, desirable that we attempt to correlate the known values and to put them into a form upon which actual progress can be based. This discussion is, then, for the benefit of that engineer, particularly the engineer in the mineral industries and more particularly in ore-dressing plants, and is merely a gathering of facts already known but difficult to segregate.

Jan 1, 1938

By Leonard Waldo

(New York Meeting, February, 1911.) THE recent and rapid development of the physics of engineering materials at temperatures as low as that of liquid air and as high is that of the electric are, has drawn renewed attention to the absence of tables, properly printed and spaced, for the convenient and accurate translation of temperature from centigrade to Fahrenheit scales and vice versa. It is to be noted that the Fahrenheit scale is the almost universal usage in foundries and shops in the United States, though the laboratories of the same works employ the centigrade notation. The growing use of the electric furnace in Germany and France calls for much American citation all in centigrade high temperatures, and while the arithmetical calculation is simple, it becomes burdensome when often repeated. I have been surprised at the numerous reprints of Table I. from centigrade to Fahrenheit degrees, first privately printed for personal use, which have been made by works, blue-prints, test-books, and technical journals, and I hope that Table II., from Fahrenheit to centigrade degrees, will be equally useful.

Jan 4, 1913

United Engineering Trustees, Inc C E Reistle, Jr (to Oct '55), A B Kinzel, '56, Andrew Fletcher, '57, Philip Kraft (from Oct '55 to '59) The Engineering Foundation W M Peirce, '56, A M Gaudin, '58 Engineering Societies Library Board Frank T Sisco, '58, C H Behre, Jr Engineering Societies Personnel Service Board of Directors E J Kennedy, Jr, E H Robie Advisory Committee, Milwaukee F T Agthe Special Survey Committee C M Cooley American Standards Association Mining Standards Board E R Borcherdt, '55, Otto Herres, '55, J K Richardson, '56, E W Bullard, '56, Alternate

Jan 1, 1955

By Mark David Rankin

This paper represents a general assessment of the primary factors driving the market for mobile offshore drilling rigs and the utility of those factors as choice variables for the offshore drilling program planner.

Jan 1, 1982

By C. S. Smith, K. K. Ikeuye

In an earlier paper1 one of the authors called attention to the significance of the relative free energies of grain boundaries and interphase boundaries in alloys in determining the shape and distribution of micro-constituents. The ratio of the interphase and inter-crystalline boundary energies (that is, —?12, where ?12 is the energy of the interface between a crystal of phase 1 and a crystal of phase 2, and ?11 is the energy of the boundary between two crystals of phase 1) will be denoted by F. It is this ratio that determines, by the simple triangle of forces relation, the dihedral angle, ?, of phase 2 where it adjoins a boundary between two grains of phase 1. On a metallographic sample various angles are actually obtained because of the random orientation of the plane of observation, but the statistically most frequent angle is the true one. These basic principles were discussed in detail in the earlier paper. The experiments described below show the effect of both composition and temperature on ? and T for some alloys containing a liquid phase, and provide data on the rate of approach to the equilibrium angles in both solid and liquid phases. All the alloys were melted in a graphite crucible and cast into ingots 3/4 by 11/8 in. cross-section. Some of the aluminum alloys consisted of two immiscible liquids from which uniform castings could not be obtained. The amount of liquid phase varied locally to a considerable extent and the analyses were meaningless. Nevertheless, the composition of the liquid would not differ from that in an alloy of the intended gross composition, and the synthetic composition of the alloys was therefore used in considering the surface energy results. The ingots were given initial deformation by cold-rolling to 50 pct reduction, annealed, and given a second 50 pct reduction prior to cutting into small samples for heat treatment at the times and temperatures subsequently reported. The resulting micro-samples were carefully prepared metallographically and examined at magnifications of 650, 1280, or 2500. The objectives used were 21X, 0.40 NA (dry); 41X, 0.65 NA (dry); and 80X, 1.40 NA (oil emulsion). The appropriate angles were measured by rotation of the stage of a Bausch and Lomb metallograph to align the appropriate boundaries successively with a cross-hair in a micrometer eyepiece. About 250 angles were measured on each phase. Though the angles were read to 1°, the accuracy is probably not above 3°, because of uncertainty in setting the cross-hair tangent to the sometimes curved boundary. The corners of very small particles, particularly in early stages of adjustment after cold-rolling, were difficult to measure and the results were slightly dependent on the magnification used (compare Fig 1-C and 1-D). With particles of larger size and more nearly equilibrium shape, magnification made no difference (vide Fig 1-F and 1-G). The measured angles were grouped in 10° intervals (5° if ? was less than 20°) and plotted in bar

Jan 1, 1950

(Members are urged to send in for this column any notes of interest concerning, themselves or their fellow-members.) Members and visitors who registered at institute headquarters during October A. Adiassewich, St. Petersburg, Russia. Charles W. Merrill, San Francisco, Cal. A. F. Lucas, Washington, D. C. Carl J. Trauerman, Butte, Mont. Allan J. Clark, Lead, S. D. Herbert B. Cox, Boston, Mass. Prof. Loewinson-Lessing, St. Peters- James W. Malcolmson, Kansas City, Mo. burg, Russia. A. E. Sunderhauf, Paramaribo, Dutch F. Maury Gillespie, Abangarez, Costa Rica. Guiana, S. A. M. Gardner Talcott, Irvington-on-Hudson, N. Y. D. W. Brunton, Denver, Colo. A. P. Watt, Newark, N. J. Dwight E. Woodbridge, Duluth, Minn. S. A. Taylor, Pittsburg, Pa. Alexander Fyfe, Boston, Mass. Ralph Wilcox, Miami, Ariz. Robert A. Seip, Wilkes-Barre, Pa. William J. Cox, Denver, Colo. A. J. Eveland, Boston, Mass. E. P. Ross, Duquesne, Pa. M. F. Sayre, Brewster, N. 1. H. Mortimer-Lamb, Montreal, Canada. Albert Sauveur, Cambridge, Mass. F. L. Grammer, Leesburg, Va. Robert H. Leach, Brockton, Mass. R. R. Moore, Mexico City, Mex. Steinar Foslie, Kristiania, Norway. Charles E. van Barneveld, San William A. Wong, Honolulu, Hawaii. Fran¬cisco, Cal.

Jan 11, 1913

By M. S. Burton, J. E. Ritter

The sessile-drop technique was employed to study the effect of atmosphere and alloy additions of titanium and chromium on the surface tension and contact angle of nickel on sapphire substrates at 1500oC. Shear tests were conducted on the solidified sessile drops. The liquid-gas surface tension of pure nickel on sapphire was found to be 1747 ergs per sq cm, with a contact angle of 109.6 deg. The surface tension and contact angle were not affected significantly by the four atmospheres, vacuum, impure argon, pure argon, and pure hydrogen. Small additions of titanium and chromium decreased the contact angle and for the same alloy content, contact angles were lower in pure argon than in pure hydrogen. On the basis of shear-test results , the most probable cause for adhesion in the Ni-Al2O system is the formation of NiO:Al2O3 spinel at the interface; in the titanium alloy-Al2O3 system adhesion is thought to be due to a mechanical interlocking effect; in the chromium alloy-Al2O3 system adhesion is believed to be the result of solid-solution formation involving Cr2O3 and Al2O3 at the interface. In the last few years there has been considerable interest in reinforcing metals with ceramic whiskers. It has been postulated that, by reinforcing nickel with sapphire whiskers, high-temperature strengths su- perior to those of the best current nickel alloys can be achieved.' To fabricate a whisker-metal composite having optimum density and strength, understanding of wettability and adherence in the system is of prime importance. Although there has been some previous research in this a a need for further studies has been cited4-8 to understand better the effects of impurities, alloys additions, and atmosphere on the wetting and bonding of metals to metal oxides. The purpose of this research was to investigate the factors involved in the wetting and adherence of nickel/nickel alloys to sapphire (single-crystal a Al2O3). Sessile-drop experiments were conducted in vacuum, impure argon, pure argon, and pure hydrogen, to determine the effect of atmosphere on the contact angle of the metals on sapphire, and the liquid-gas surface tension of pure nickel. The solidified sessile drops were sheared from the sapphire substrate to measure the bond strength between the metal and ceramic. The alloy additions chosen were titanium and chromium since both enhance the wetting of nickel on sapphire.2, 3c Also, titanium is commonly used when brazing metal-to-ceramic seals to improve adherence. Since chromium forms an oxide that is completely soluble in sapphire, it was thought that the oxide could serve as a transition phase to promote bonding between the Ni-Cr alloy and sapphire. I) EXPERIMENTAL APPARATUS AND PROCEDURE The sessile-drop apparatus was a horizontal furnace, with an induction-heated, cylindrical molybdenum susceptor in a water-cooled Pyrex chamber. This apparatus was patterned after that of Williams and Nielsen.7 A flat Pyrex window at each end of the furnace allowed temperature measurements to be made at one

Jan 1, 1968

By V. H. Wilhelm

In contrast with the previous year's activity, the California oil industry for 1938 showed a decrease in drilling, market demand, and discovery of new oil reserves, although there was an increase in oil production. Although additions to reserves from new fields and extensions were less than withdrawals during the year, reappraisals of discoveries in 1937 added to new discoreries during 1938 amounted to over 300,000,000 bbl. The following comparative statement shows the important changes in various phases of the industry: Throughout the year the storage situation became progressively more acute, owing principally to less Pacific foreign demand, and increased potential from drilling the newly discovered fields and pools (Fig. 1). California storage increased approximately 32,000,000 bbl. during 1938, most of which (approximately 18,000,000 bbl.) was heavy crude and residuum. The market demand for the year was around 600,000 bbl. per day. Because of the trend toward Diesel power for heavy transportation, the non-gasoline-bearing crudes arc fast becoming a drug on the market. New discoveries were instrumental in increasing the potential production of the state from 1,076,000 bbl. per day in January to an all-time high of 1,420,000 bbl. per day at the close of the year; although the indicated reserves of these new discoveries were not equal to the yearly withdrawal of 249,000,000 bbl. As of the end of 1938, the state was voluntarily curtailed about 58 per cent. As a result of prospecting during the year, six new fields were discovered, three fields were extended, and deeper zones were reached in five of the older fields.

Jan 1, 1939

By V. H. Wilhelm

In contrast with the previous year's activity, the California oil industry for 1938 showed a decrease in drilling, market demand, and discovery of new oil reserves, although there was an increase in oil production. Although additions to reserves from new fields and extensions were less than withdrawals during the year, reappraisals of discoveries in 1937 added to new discoreries during 1938 amounted to over 300,000,000 bbl. The following comparative statement shows the important changes in various phases of the industry: Throughout the year the storage situation became progressively more acute, owing principally to less Pacific foreign demand, and increased potential from drilling the newly discovered fields and pools (Fig. 1). California storage increased approximately 32,000,000 bbl. during 1938, most of which (approximately 18,000,000 bbl.) was heavy crude and residuum. The market demand for the year was around 600,000 bbl. per day. Because of the trend toward Diesel power for heavy transportation, the non-gasoline-bearing crudes arc fast becoming a drug on the market. New discoveries were instrumental in increasing the potential production of the state from 1,076,000 bbl. per day in January to an all-time high of 1,420,000 bbl. per day at the close of the year; although the indicated reserves of these new discoveries were not equal to the yearly withdrawal of 249,000,000 bbl. As of the end of 1938, the state was voluntarily curtailed about 58 per cent. As a result of prospecting during the year, six new fields were discovered, three fields were extended, and deeper zones were reached in five of the older fields.

Jan 1, 1939