Search Documents

By A. D. Hughes

C. W. MERRILL*—Mr. Hughes' paper not only is very well presented but is most timely in that it covers a subject of vital interest to the United States. Tin is one of the strategic metals which has not been found here in appreciable quantities. The total United States tin output since the first recorded production over 100 years ago would not supply current consumption for a fortnight. On the consumption side, tin is extremely important in national defense because of its use in tin plate which, in the form of tin cans, makes it possible to feed properly the armies that the United States recruits from its civilian population in emergencies. Moreover, the internal combustion engines so important in powering tanks, planes, and other war machines, require large quantities of tin alloys for bearings and for soldering. These considerations, along with the fact that Malaya, historically, has been the leading source of tin to the United States, make the kind of information that Mr. Hughes has presented so ably. a matter of vital interest. Your Chairman, Mr. Romanowitz, in his introduction, referred to the fact that I had been a member of the United States delegations to the three meetings of the International Tin Study Group. Some cominents on the Group's objectives and deliberations may be of interest. When it appeared that the International Tin Committee, the prewar producer's cartel, might soon revive its operations and extend its control agreement beyond the expiration date of Dec. 31, 1946, the United States Government became interested in some kind of an international trade organization concerned with tin which would give the consumers' interest equal representation with the producers' interests. An international meeting was called in London in October 1946 to consider this problem. I did not attend that meeting hut the result of the meeting was the organization of the International 'Tin Study Group which

Jan 1, 1950

By William J. Priestley

In the manufacture of gun forgings and other steel parts that, in service, are subject to sudden high stresses and shocks, it is most desirable to use steel possessing the greatest toughness and ductility possible without sacrifice of strength. In order to obtain this condition, it is necessary to procure steel that shows the highest possible elongation and reduction of area without lowering the tensile strength and clastic limit. Proper heat treatment of the steel can control this condition within certain limits. When heat treatment has failed to produce the desired results, metallurgists have used steels containing molybdenum, zirconium, vanadium, chromium, tungston, etc. The purpose of this paper is to describe a method by which these desired physical properties may be procured—by the elimination of certain impurities that inherently exist in steel made by the open-hearth process, and without the use of expensive alloys. Design of Gun Forgings In the manufacture of gun forgings, a certain elastic limit is fixed by the designer, and the walls of the gun arc made of the proper thickness, allowing a suitable factor of safety for the high stresses and sudden shocks that occur during gun firing. The clastic strength of the gun is about 1.4 times the stress set up at any point along the bore of the gun during firing with the maximum powder charge. As the stresses set up in the walls of the gun during firing are mostly "tangential," all physical tests are taken in this direction. Due to the length of the forgings, these tangential test bars are always taken at right angles and transverse to the direction of flow of the metal in forging. Furthermore, test bars taken across the grain of the metal will more frequently expose defects and foreign inclusions in the steel than will bars

Jan 1, 1922

By William J. Priestley

In the manufacture of gun forgings and other steel parts that, in service, are subject to sudden high stresses and shocks, it is most desirable to use steel possessing the greatest toughness and ductility possible without sacrifice of strength. In order to obtain this condition, it is necessary to procure steel that shows the highest possible elongation and reduction of area without lowering the tensile strength and clastic limit. Proper heat treatment of the steel can control this condition within certain limits. When heat treatment has failed to produce the desired results, metallurgists have used steels containing molybdenum, zirconium, vanadium, chromium, tungston, etc. The purpose of this paper is to describe a method by which these desired physical properties may be procured—by the elimination of certain impurities that inherently exist in steel made by the open-hearth process, and without the use of expensive alloys. Design of Gun Forgings In the manufacture of gun forgings, a certain elastic limit is fixed by the designer, and the walls of the gun arc made of the proper thickness, allowing a suitable factor of safety for the high stresses and sudden shocks that occur during gun firing. The clastic strength of the gun is about 1.4 times the stress set up at any point along the bore of the gun during firing with the maximum powder charge. As the stresses set up in the walls of the gun during firing are mostly "tangential," all physical tests are taken in this direction. Due to the length of the forgings, these tangential test bars are always taken at right angles and transverse to the direction of flow of the metal in forging. Furthermore, test bars taken across the grain of the metal will more frequently expose defects and foreign inclusions in the steel than will bars

Jan 1, 1922

By L. Adler

A relatively simple and effective technique is proposed to deal with the failure of geologic masses containing weakness planes. This technique, termed irextended" rupture envelope, provides a means to clearly distinguish rock and soil from fractured rock and, on a theoretical level, considers a matrix-inclusion system. It may also constitute the link between Mohr's and Griffith's failure theories. Included in the article are five sample problems concerning site location, structural design, strengthening the plane of weakness, changing the magnitudes of major and minor principal stresses and changing the orientations of major and minor principal stresses. Engineers trying to solve design problems in rock and soil mechanics have often assumed an iso-tropic and homogeneous medium. For naturally occurring geologic masses this assumption has always been viewed with regret. The following analysis which deals with the effects of plane anisotropy on failure presents a solution to this. The planes of weakness are joints, faults, bedding planes, fracture and cleavage (natural and induced), foliation and schistosity. The physical properties of these weakness planes include an undulating surface, frictional resistance, discontinuous extent, filling material, tightness and presence of water to cause a hydrostatic pore pressure. All of these properties relating to failure can be summarized in Mohr's rupture envelope for the plane of weakness. This, along with the geometrical orientation, strike and dip, of the plane of weakness produces what is termed an irextended" rupture envelope. MOHR'S STRESS CIRCLE AND RUPTURE ENVELOPE The significant features of these concepts are listed below.' 1) A point on the u - r coordinate plane represents the normal and tangential stress components on a reference area in the material. This area can have any orientation. (Fig. la)

Jan 1, 1963

By S. A. Falconer

Much attention and publicity has been given, during recent years, to grinding, classification, flotation, and thickening. The various technical papers, and symposiums held to discuss these important phases of milling, have contributed to a better under- standing of the fundamental principles and operating variables involved. Another important part of milling- to the flotation operator-is a treatment step to which frequently too little attention is given-" conditioning," or the treatment the ground mineral pulp receives before it enters the flotation machines. Conditioning" is a hackneyed and frequently misused term, commonly employed to describe the pretreatment of surfaces of minerals in ore pulps or mill pr6ducts prior to froth flotation. In general, such pretreatment is for the purpose of changing the flotation characteristics of these mineral surfaces to enable them to respond in some desired predetermined manner when subjected to flotation. Taggartl states that the function of conditioning is "either to insure selective collector coating of one mineral species while another species is not; or to take such steps as will compensate for departure there from."

Jan 1, 1949

By V. Pasupathi, R. E. Hummel, J. W. Koger

Specimens of P1 brass were plastically deformed at room temperature to various degrees of deformation and subsequently cooled in order to transform them to low-temperature martensite. Deformation shifts Ms. A, , and the temperature of minimum resistivity to lower temperatures, and also decreases the temperature coefficient of electrical resistivity. These properties change rapidly up to about 15 pct reduction but vary very little with higher deformation. The possible relationships between martensite formed by deformation and the M, temperature of low-temperature martensite are discussed. Evidence is given that deformation martensite delays the formation of low-temperature martensite. BETA' brass undergoes at least two different types of martensitic transformations. One of these transformations (B1- B2) was first observed by Kaminski and ~urdjumov' and occurs when 81 brass with a zinc content between 38 and 42 wt pct (quenched from the single-phase region) is cooled below room temperature. Jollev and Hull' determined the structure of 0" from X-ray and electron-diffraction data as ortho-rhombic. Kunze came to the conclusion that the super-lattice cell of 0" is one-sided face-centered triclinic (pseudomonoclinic). The second martensitic transformation (B1-A1) occurs when the specimens are deformed at or somewhat above room temperature. This type of martensite will be called deformation martensite. Horn-bogen, Segmuller, and Wassermann4 determined the structure of deformation martensite to be bct. (An intermediate phase, az, occurs before the final phase appears.) At deformations higher than 70 pct, a, transforms into a.4 A critical temperature Md exists above which no transformation occurs during deformation and is estimated to be around 400°C in P1 brass.5 This martensite has elastic properties.6 When the sample is stressed, martensitic plates appear; when the stress is released, the plates disappear. The present paper studies the effect of deformation martensite on the formation of low-temperature martensite. The experiments involved samples of 8, brass which were plastically deformed by various amounts and were subsequently cooled below the transformation temperature. EXPERIMENTAL PROCEDURE The 13 brass investigated was made from 99.999 pct pure copper and 99.9999 pct pure zinc and contained 38.8 wt pct Zn. The specimens, consisting of foils 0.1 mm in thickness, were heat-treated at 8'70°C for 15 min in an argon atmosphere and then quenched into ice water. They were then deformed by cold rolling and subsequently cooled at a rate of 1°C per min. The martensitic transformation that occurred during cooling was followed by electrical resistivity measurements. The resistance measurement technique and its accuracy have been described in a previous paper. Because the transformation 81 —-8" occurs below room temperature, the samples were placed in a cryo-stat which contained isopentane as a cooling medium. The isopentane was cooled by liquid nitrogen pumped under pressure through a 15-ft coil of copper tubing which was immersed in the isopentane. The nitrogen flow was regulated by a temperature controller using two thermistors in the cooling medium. The cryogenic liquid could be heated with an immersion heater. The useful temperature range with this device was from +25° to approximately -155~C. EXPERIMENTAL RESULTS Resistivity Measurements. The following abbreviations are used in this paper to label the characteristic temperatures during the martensitic transformation. M, is the starting point of the martensitic transformation and is defined as that temperature where the resistivity vs temperature curve on cooling first deviates from a straight line. Mf is the temperature at which the martensitic transformation is completed. On reheating, the transformation from martensite to the parent phase starts at a temperature A, and ceases at a temperature Af. Fig. 1 presents five different resistivity vs temperature curves corresponding to the transformation of brass from Dl to 8" after different degrees of reduction in thickness. The following observations can be made from these curves. 1) With increasing degree of deformation the Ms temperature is shifted to lower temperatures. This shift ranges up to 35°C compared to the undeformed state. This is also indicated in Fig. 2, where AM, (the shift of Ms, compared to the undeformed state) is plotted vs the degree of deformation. AM, increases rapidly until a reduction of about 15 pct is reached. With higher deformations, no additional increase in AM, was found. 2) With increasing degree of deformation the temperature of minimum resistivity (M) is also shifted to lower temperatures. The shift, attains a maximum of about 61°C compared to the undeformed state. In Fig. 3, AM is plotted as a function of deformation. It can be seen that, as in 1 above, AM increases rapidly and no further shift of M occurs for deformations greater than 15 pct. 3) The temperature coefficient of resistivity, is given by the slopes (dp/dT) of the linear portions of

Jan 1, 1969

By C. H. Mathewson

MICROSCOPIC rnetallography has been exploited quite well enough to bring about a very general understanding that the typical metal or alloy is composed of minute crystalline particles blended into a coherent microstructural mosaic. One does not have to be a specialist in metallography to realize that the properties of such an aggregate are essentially a summation in appropriate form of individual effects derived from the shape, size, placement or orientation and cohesive characteristics of the component particles. It is clearly of great importance to consider the various forms of discontinuity which may occur at the boundaries between these crystalline particles. When a number of particles each possessing the same orderly arrangement of atoms are brought together into a close-fitting system of purely haphazard contacts, not unlike a handful of snowflakes compacted into a snowball, the particles are said to possess random orientation. There are no generally accepted views concerning the arrangement of the atomis or the constitutional reaction between atoms where one crystal meets another, but these contact regions are characterized by strength rather than weakness and it is customary to require the presence of many rather than few boundaries in preparing metal for useful service. Under certain circumstances all of the particles in a metal may be nearly alike in orientation. Other general tendencies of orientation may be associated with particular forms of mechanical and thermal treatment. In contrast with these cases of fortuitous or statistical diversity of orientation, we often find adjacent particles united along a plane which possesses a grouping of atoms belonging equally well to both structures. This, of course, determines a fixed relationship between the two orientations and it is always possible to derive one from the other by some form of rotation or reflection prescribed by the symmetry of the crystal structure under consideration. Particles united in this manner are known as twin crystals although the term refers to the form of association rather than the number of individuals concerned.

By S. V. Krusiewski, J. W. Gabelman

Regional metallogenic zones and areas of equal paragenetic range have been interpreted from a compiled metallogenic map. of Mexico. Mineralization gradients of the pattern subsequently identified extend inland from coastal zones of high-temperature mineralization, and join in a central longitudinal zone of relatively low-temperature mineralization, apparently leaving no zonal room for lowest temperature deposits. The striking regional zoning pattern can be correlated with regional deformation gradients of similar position and orientation. The gradients represent at least three major orogenic cycles in two structural belts. Paleozoic structural belts existed along each coast with deformation gradients diminishing inland toward a narrow, central peninsular craton. The Mesozoic-Tertiary Mexican (Cordilleran) belt covered the entire country with a gradient oriented toward the Gulf of Mexico. Most ore deposits in this belt are of Tertiary age, although Tertiary mineralization gradients seem to have "inherited" the pattern left by Paleozoic tectonic gradients. Mineralization gradients can be used to identify the regions most favorable for the occurrence of selected metals. A metallogenic province is characterized by particular proportions of various metals, and the relative proportions can vary from province to province; but within any province the same intensity of mineralization would produce similar deposits in different places. Declining intensity of minetalization produces different kinds and sizes of deposits in zones that are concentrically arranged around sites of strongest rock alteration. On a regional basis, districts of similar average intensity of mineralization occur in zones that generally parallel some tectonic grain with the result that tectonic deformation has been designated a principal cause of mineralization. Variations in the type and intensity of deformation would determine the type as well as size of metal deposits. Mexico is especially favorable for such a study be- cause of its great abundance and variety of epi-genetic mineral deposits in various lithologic, structural and tectonic environments. The concept is also useful in recognizing portions of Mexico favorable for the occurrence of specific metals. METALLOTECTONIC ZONING IN MEXICO Theory: In studies of individual districts and groups of districts throughout North and South America, areal zoning of metal deposits generally seemed to respond to the paragenetic sequence of iron, gold, copper, zinc, lead, silver, antimony and arsenic, gold and fluorite. However, the definition of district zones is greatly obscured by contemporaneous or rhythmic deposition of metals, especially in the middle of the paragenetic range, and by the common superimposi-tions of different generations of metals. Zones could usually be distinguished only for groups of metals, such as early precious metals, base-metal sulfides, sulfosalts and late precious metals. The best defined zoning in a district is normally the spatial separation of the greatest volumes of altered and metallized rocks.' Exceptions are districts representing the high- and low-temperature extremes of the mineralization range where the former creates a matrix for the latter. In most districts the total quantity of alteration products is greatly in excess of, and appears to be roughly proportional to, the total quantity of metallization products. Subsequent to the bicomponent nature of each district, the most important mineralogical feature is the great excess of one to several metals or minerals which results in a district identifiable as one of predominantly gold, copper, lead-zinc, fluorite, etc., although a great variety of other elements may be present. The para-genetic range for the abundant elements in any district is only a portion of the entire possible range for all the elements representing the complete process throughout the region. Early during investigations of this type, it became apparent that the consistent bicomponent character of districts allows two methods for studying epi-genetic mineralization patterns. One is to identify and plot altered rock "pipes,"* which are easily recognizable in the landscape by their anomalous

Jan 1, 1969

By Frederick Laist

F. N. FLYNN, Clifton, Ariz.-I would like to ask Mr. Mathewson what percentage of his leaching liquor is wasted at this time? It has a bearing on the question in connection with the New Cornelia, and I think it is a very important question. E. P. MATHEWSON, Anaconda, Mont.-I am not sure what the percentage is now, but we don't discard the strong liquors. Something like 25 per cent. of the wash water taken out each day is sent over a special set of scrap iron tanks, and the copper recovered there. We had a little trouble at first. We did not proceed to use the sponge iron for the reason that the plant we originally contemplated was abandoned for flotation. Our original idea was to use a leaching process on all the tailings of the mill, but we found it would take a great deal of time to build a plant; and the cost of operating the plant we estimated to be about the same and the recovery the same. It was a question of time with us, and we decided to adopt flotation. That changed our plans. We now have the leaching plant, treating the tailings of the old dump, and the flotation applied to the current tailings. The sponge iron was figured for the large plant. We can get all the scrap iron necessary for the small plant-plenty from the scrap produced in the main plant of the smelter.

Jan 12, 1916

By W. M. Weigel

The general term "sand" applies to a multitude of similar materials consisting of fine granular mineral. As usually understood, it means the ordinary natural product used for structural purposes and made up largely of grains of quartz. Quartz sand constitutes by far the greater bulk of the production, but there are other grades used for industrial purposes, such as molding sand, glass sand and many others, that may be grouped under the general name of special sands. Under this general group would fall filter sand, sand-blast sand, engine sand, potter's sand, abrasive sands of all kinds, sand for pulverizing, roofing sand, flooring sand, fire or furnace sand, standard sand, burnishing sand, sand for magnesium oxychloride cement-plasters and sand for chemical and metallurgical purposes. Sources of Supply Sand is a widely distributed natural product and even the better grades are low-priced commodities. For these reasons development has occurred near points of consumption where sand meeting the requirements is available. Some special grades, however, cannot be prepared from any sand bed and shipments are often made over considerable distances when the only developed deposit is remote from the consuming center. This is true of filter sand, sand-blast sand, sand for pulverizing and some of the others when chemical purity or grain size, coupled with the need of a properly equipped plant for preparation, are required. New Jersey is a large producer of filter, engine, sand-blast, fire, and pulverizing sand. Pennsylvania, and West Virginia produce special sands for pulverizing, fire sand, abrasive sand, engine sand and sand for chemical and metallurgical use. Ohio produces much sand-blast, fire and abrasive sand, and some filter sand. Illinois and Minnesota produce

Jan 1, 1926

By C. E. Arnold

THE CHAIRMAN (PERCY G. BECKETT, Globe, Ariz.).-When you are at Miami tomorrow, you will see a very interesting comparison on the surface of the two mining methods that are being employed there largely. In the case of the surface over the Inspiration mining method, you won't see very much left of the surface. Everything has gone down. In the case right at the line of the Inspiration ground and the Miami, you will see that the surface over the top slicing which the Miami company has been doing in that country has been riding down evenly and uniformly; and it gives a very marked comparison of the two types of mining, and, to a certain extent, of the different degrees of waste dilution. I would ilke to hear from Mr. Maclennan on this subject. F. W. MACLENNAN, Miami, Ariz.-A paper based on percentage extraction by shrinkage stoping is a difficult one to discuss for the reason that it is hard to arrive at extraction figures until a section has been completely mined out. In the Miami mine we are using a method of shrinkage stoping with narrow stopes and pillars. This ore has been completely broken up and we have started in at the far end to draw off the ore mass maintaining the top of the broken ore dipping at an angle of 60° away from the direction in which we are retreating. A very important point I think about drawing a large. mass of ore down at an angle rather than trying to maintain the top of the ore more or less horizontal is that drawing at a steep angle has a tendency to create a horizontal movement in the ore mass as well as the vertical movement of the ore traveling down to the drawing off chutes. We know that this takes place, on account of the horizontal movement of marked

Jan 12, 1916

By E. S. Moore

The Kolar gold field has been for a long time the most important gold-producing area of India. It is situated in the Skate of Mysore, southern India, and not far from the City of Bangalore. The productive field is about 3 miles long and in it a gold-bearing quartz vein varying in width from 1 in. to over 10 ft. is worked. The vein carries high values to great depths and many of the mines have paid large dividends. Geological Formations In KolaR Region The rocks of the Kolar region are pre-Cambrian in age and bear a close resemblance to some of the pre-Cambrian formations of America. The oldest rocks seen are basic lavas, now mostly altered to hornblende-schists, with which is associated some banded iron-formation; these rocks are similar to the Keewatin schists and iron-formation in the Lake Superior region. The schist is cut by the gold-bearing quartz vein. In certain parts of the area there is also a conglomerate containing pebbles of granite, jasper, and schist. The matrix resembles a hornblende-schist and is intruded by small granite dikes, which in some cases have been pinched off by squeezing of the rock. This has led Dr. W. I?. Smeeth, Chief Inspector of Mines of Mysore, to whom the writer is greatly indebted for information regarding this area and for his hospitality while visiting the field, to regard this conglomerate as a breccia due to crushing of granite dikes in the schist. Dr. J. W. Evans has regarded the conglomerate as probably a squeezed glacial boulder clay. From analogy with pre-Cambrian conglomerates in America, the writer regards it as a metamorphosed rock similar to our basal Huronian conglomerate. However, the main bearing which it has upon the problem under discussion is the apparent fact that it is younger than the schist and that it indicates the presence of a syncline in the rocks cut by the quartz vein. Surrounding the area of schist and conglomerate is a large mass of granite-gneiss resembling the Laurentian gneiss of the Lake Superior region. Still later than the rocks mentioned above are basic intrusions which cut the quartz and schists; in the mines these are known as trap. One dike of this type is 50 to 60 yd. wide.

Jan 1, 1920

By R. W. Raymond

This name is applied to the present mining law, as enacted in 1872 and since, to indicate its leading characteristic—in which it differs from all previous mining laws of this or any other country. The earlier act, passed in 1866, was practically the first attempt of Congress to deal with the question of mining titles upon the public domain. It was framed after nearly twenty years of acquiescence on the part of the Government in the self-constituted tribunals, officials, rules, and customs of the mining districts. In its recognition of these, and in several other particulars, the act of 1866 was open to serious criticisms. It is the purpose of this paper, not to trace the history of legislation on this subject, or show in detail what were the faults of the earlier law, but rather, by a discussion of certain aspects of the present law, to point out how great a revoluition it has effected in the rights of mining locators, and to indicate some of the difficulties attending its application. In the attempt to correct the vagueness of the act of 1866 an entirely new elernent was introduced into the law, bringing with it a new set of difficulties. Under the act of 1866 and the miners' customs which it followed, the lode was the thing claimed and subsequently acquired by patent. And the claim to a given number of feet on the longitudinal course of the lode was rooted in 'a discovery of any part of the lode in any part of the claim. ("Extensions" could in many districts—perhaps universally—be located and claimed on the strength of the discovery in the principal claim to which they referred; but this is a point not essential to the present discussion.) It was not necessary to find the outcrop or the upper edge of a lode in order to lay a valid location upon it. An explorer, sinking a shaft and intersecting a lode not already discovered and claimed by another, could claim by that discovery the number of feet along that lode which the local laws might permit (not exceeding the maximum set by the United States statute) whether his sur-

Jan 1, 1884

By C. H. Mathewson

MICROSCOPIC. rnetallography has been exploited quite well enough to bring about a very general understanding that the typical metal or alloy is composed of minute crystalline particles blended into a coherent microstructural mosaic. One does not have to be a specialist in metallography to realize that the properties of such an aggregate are essentially a summation in appropriate form of individual effects derived from the shape, size, placement or orientation and cohesive characteristics of the component particles. It is clearly of great importance to consider the various forms of discontinuity which may occur at the boundaries between these crystalline particles. When a number of 'particles each possessing the same orderly arrangement of atoms are brought together into a close-fitting system of purely haphazard contacts, not unlike a handful of snowflakes compacted into a snowball, the particles are said to possess random orientation. There are no generally accepted views concerning the arrangement of the atoms or the constitutional reaction between atoms where one crystal meets another, but these contact regions are characterized by strength rather than weakness and it is customary to require the presence of many rather than few boundaries in preparing metal for useful service. Under certain circumstances all of the particles in a metal may be nearly alike in orientation. Other general tendencies of orientation may be associated with particular forms of mechanical and thermal treatment. In contrast with these cases of fortuitous or statistical diversity of orientation, we often find adjacent particles united along a plane which possesses a grouping of atoms belonging equally well to both structures. This, of course, determines a fixed relationship between the two orientations and it is always possible to derive one from the other by some form of rotation or reflection prescribed by the symmetry of the crystal structure under consideration. Particles united in this manner are known as twin crystals although the term refers to the form of association rather than the number of individuals concerned.

Jan 1, 1928

By Harrison Souder

THE object of this paper is to bring to. the notice of engineers a safety detonating fuse by the use of which misfires in blasting may be eliminated and safety in blasting operations promoted. This new detonator is a French invention and is known as Cordeau detonant or detonating fuse and is sold under the name of Cordeau-Bickford. It consists of a lead tube 5 to 6 mm. in diameter, filled with trinitro-toluene. While applicable to all classes of mining it will appeal especially to those who have to do with deep-hole blasting in open-cut clines or quarries, or any operations where a large number of holes are to be shot at one time. Since the introduction of the deep-hole blasting in the Cornwall iron mines, much trouble has been experienced from misfires and many experiments were made to determine the best and safest method of blasting. Before the introduction of the detonating fuse it was found that to insure the best results, two or more high-power electric exploders, not less than No. 6, with specially insulated conductors, should be placed in each hole; the holes wired in parallel, and for a large number of holes the current to be supplied by a live wire to the bus or lead wires at about the middle of the bench. The voltage in general use is 110 to 220, but as our material is a magnetic iron ore and the holes are generally damp, we found it advisable to reduce this to about 30 volts to prevent short circuits. A No. 7 or No. 8 special insulated detonator was adopted. But with the best of care and attention to the minutest detail, we were not able to eliminate occasional misfires and the consequent ever present danger of accidents.

Jan 10, 1914

By Thomas G. Murdock

EthIopia, the first country to be liberated from Axis domination, has recovered remarkably from the ravages of occupation and war. Mineral production has contributed significantly towards this recovery, as it has provided a means of obtaining foreign exchange and has given employment to hundreds of workmen whose maintenance otherwise would have presented a problem. Although primarily an agricultural country, never with a large mineral production, Ethiopia has within its borders a variety of minerals, both precious metals and nonmetallics. Some of these are important to the country as a national asset and others contribute greatly to local economy and can be expected to do so even to a greater extent in the future1 (Fig I). Physiography and Geology The Empire of Ethiopia is essentially a mountainous and volcanic country, in northeast Africa, situated principally between latitude 4° and 15°N and longitude 34° and 44°E. It is bounded on the north by Eritrea, on the northeast by French Somaliland, on the southeast by Italian Somaliland, on the south by Kenya Colony, and on the west by Anglo-Egyptian Sudan. These European possessions thus completely surround the country. Its access to the Red Sea is through Eritrea; to the Gulf of Aden, through French or British Somali- land ; and, to the Indian Ocean, via Italian Somaliland. These routes range in length from 40 to 250 miles. Ethiopia has an area of approximately 350,000 square miles, with a width from north to south of 625 miles, and a maximum length from east to west, along latitude 8°N, of about 875 miles. Physiographically the country is characterized by two very extensive sub-tabular plateaus: the Ethiopian Plateau to the northwest and the Somaliland Plateau to the southeast, separated by a long tectonic graben—the Rift Valley of the Galla Lakes and Danakil. The Ethiopian Plateau, deeply cut and notched by the drainage, slopes in a general northwest direction toward the Sudanese Plains and the valley of the Nile; the Somaliland Plateau slopes to the southeast, toward the Indian Ocean. The valley of the Galla Lakes and its extension to the northeast—the Awash River Valley, separates the plateaus, from Lake Rudolph to Danakil. This depression which constitutes a continuation or ramification of the Great Rift Valley of Central Africa joins in turn the trough of the Gulf of Aden and the Danakil-Eritrean Rift, continuations of the Red Sea and the Jordan Valley. The general basement of Ethiopia is made up of very old rocks, usually considered as Archaen.2 These rocks are represented by the metamorphic crystallines, such as gneisses, different kinds of schists, included lenses of crystalline limestone, and massive intrusives such as granites, diorites, and syenites, all cut by

Jan 1, 1949

By C. A. Stickels

The preferred crystallographic orientations developed during recrystallization of polycrystalline electrolytic iron sheet, cold-rolled 90 pct, were ivestigated. Recrystallization at 500° or 565° C for relatively short limes produces a texture which is similar to the rolling texture. A duplex partial fiber texture, significantly different from the rolling texture, is found when the annealing time is increased. Recrystallization at 700°C also produces a sequence of textures with increasing annealing time. In order of their appearance, these textures are: 1) the duplex partial fiber texture found at lower temperatures, 2) a four-component texture "near {322}(296)", 3) a {112)(110) +(111)(110) texture, and 4) a two-component "near {554)(225)" texture. Secondary recrystallization, or discontinuous grain growth, accompanies the development of the latter texture. However, the "near {554} (225)" texture was nol observed when secondary recrystallization occurred under other conditions. All of the ideal orientations found in recrystallization textures can be accounted for by the growth of minor components of the deformation texture. IN recent years there has been increased interest in improving the drawability of metals by controlling the preferred crystallographic orientation of the sheet.1-l3 Since more low-carbon steel is drawn than any other material, considerable attention has been focused on the properties of sheet steel. Efforts to improve drawability through texture control have been hampered by the lack of any published systematic study of the recrystallization textures developed in iron annealed below Acl. The purpose of the present work was to supply some of this missing information, specifically, the recrystallization textures obtained by isothermal anneals of polycrystalline iron, cold-rolled 90 pct. LITERATURE REVIEW—DEFORMATION TEXTURES Barrett14 reviewed and summarized the investigations of rolling textures in iron and low-carbon steel prior to 1952. The texture of heavily deformed iron (rolled 90 pct or more) is described as consisting of two partial fiber textures. The dominant fiber texture (designated here as fiber texture A) has a (110) fiber axis in the rolling direction and includes the orientations (001)[110], {112}( 110), and {111}(110). The secondary texture (designated here as fiber texture B) is described as having a (111) fiber axis in the sheet normal direction, and includes the orientations {111)( 110) and (111)(112). Since the publication of Barrett's book, there have been two detailed studies of the deformation texture in polycrystalline iron. In both instances, the more sensitive diffractometer methods of pole-figure determination were used. Bennewitz15 studied the cold-rolling textures developed in polycrystalline low-carbon steel and a 3 pct Si steel. He determined (110), (2OO), and (222) pole figures for specimens reduced 30, 50, 60, and 90 pct and analyzed his results in terms of partial fiber textures. He distinguished three stages in the development of the final deformation texture. 1) Grains rotate to form two incomplete fiber textures, with (110) fiber axes inclined 30 deg to the sheet normal toward the rolling direction (fiber texture B). After 50 pct reduction, the highest density of poles is near an ideal orientation {554}(225), the two components of which are members of this duplex fiber texture. 2) With increasing amounts of reduction, grains rotate about the former fiber axes toward ideal orientations of the type {112)( 110) (common to fiber textures A and B). 3) Finally, grains rotate about their ( 110) axis in the rolling direction, clockwise and counterclockwise from the orientations {112}(110). This produces the range of orientations from (111)(110) to (001)(110) commonly found in the rolling texture of heavily deformed iron (fiber texture A). No significant difference was found between the deformation textures of low-carbon and silicon steels. A few years earlier, Haessner and weik16 had determined (110) pole figures for carbonyl iron rolled to 30, 60, 80, and 90 pct reduction in thickness. heir data agree quite well with the more complete data of Bennewitz, but a somewhat different description of the evolution of the deformation texture was given. The appearance of (110) poles in the transverse direction is ascribed to a (100)[011] component rather than "near {554}( 225) " components, and the (110) fiber axes of fiber texture B are described as located 35 deg rather than 30 deg from the sheet normal. Both of these studies agree that the secondary texture present in heavily rolled iron, the duplex fiber texture B, has (110) fiber axes and not a single ( 111) fiber axis normal to the sheet, as

Jan 1, 1965

By N. F. Schulz, H. A. Lex

Representative samples of typical manganiferous iron ores from the Cuyuna Range, Minn., were reduced to the metallic iron state at temperatures just short of fusion with an excess of coke in the manner prescribed by the R-N Direct Reduction Process. The magnetic separation characteristics of the reduced ores were determined at several grinds by means of the Davis magnetic tube concentrator. The efficiency of metallic iron concentration by magnetic separation was a direct function of the degree of metallization of the ore sample and of the degree of liberation at-tained in grinding. Some improvement of liberation characteristics was observed if a small amount of sodium chloride was present in the ore during reduction. Despite the extremely fine-grained structure of the crude ores, iron concentrates containing more than 90% Fe at iron unit recoveries of 90% or more were obtained from well-metallized samples of three of the four ores tested. The rejection of manganese to the tailings corresponding to such separations varied from 80% to 95%. The manganiferous iron ores of the Cuyuna Range in Minnesota constitute a major potential source of manganese in the United States provided that a technically and economically feasible process can be devised for its recovery. The iron and manganese of these ores occur chiefly as oxides or carbonates in the form of very small, irregular, discrete grains embedded in a matrix of quartz or other siliceous gangue. The present investigation was undertaken as a sequel to an earlier one conducted jointly by the U.S. Bureau of Mines and the R-N Corp. Those results indicated that the R-N Direct Reduction Process might be a means for recovering both a metallic iron concentrate and a marketable manganese by-product from Cuyuna manganiferous iron ores.' The R-N Process is one of many proposed schemes for the treatment of crude iron ores involving the di- rect reduction of the iron content to metallic iron followed by physical extraction of the iron. In general, it consists of the following stepsz2 1) Iron oxide in crushed natural ores or iron concentrates is about 95% reduced to metallic iron at elevated temperatures but without fusion in a rotary kiln in the presence of a solid carbonaceous fuel (usually coke), limestone, and combustible gases. 2) The kiln product, consisting of metallized ore, excess coke, lime, and coke ash is cooled. The excess coke is recovered and recycled to the kiln feed. 3) The metallized ore is ground for liberation and magnetically separated to yield a metallic iron concentrate. 4) The metallic iron concentrate is agglomerated by a briquetting process. The reduction kiln temperatures must be high enough for the desirable chemical reactions to proceed at practical rates without causing fusion of any of the ore constituents. The time of exposure of the ore to the reducing conditions must be ample for 90% to 95% metallization of the iron oxides present. If more than 95% of the iron is metallized, however, difficulties may arise in the briquetting step, presumably because of accompanying higher carbon content of the metallic iron. Although not always necessary, powdered limestone or dolomite may be added at some time during reduction to aid in eliminating sulfur and phosphorus from the final product.3,4 Other additives, notably sodium chloride, when present during reduction, result in improved liberation characteristics of the metallic iron from certain reduced ores.'v6 Under the reducing conditions normally employed, P(co + H2)= 1 atmosphere, and 1830' to 2150°F (1000° to 1170°C), the R-N Process is claimed to be adaptable to a wide variety of low, medium, and high grade iron and manganiferous iron ores. The manganese oxides and carbonates are reduced mostly to nonmagnetic MnO which is rejected to the nonmagnetic tailings. Manganese-bearing pyroxenes of the original ore, however, may be rejected poorly, if at all, apparently because these minerals occur within the iron lattice or are entrapped in the metal particles.7 The investigation was limited to studies of the Cuyuna ores listed in Table I, which were reduced to the metallic iron state under various conditions

Jan 1, 1969

By Morris Muskat

A theory is presented for calculating the performance history of complete water-drive systems producing from idealized stratified formations. The general equations are applied to systems where the permeability stratification is either of the exponential or linear type. Calculations were carried through for different degrees of permeability stratification, but with special emphasis on the effect of the mobility ratio between the produced oil and the invading water on the resultant performance. These results are also expressed graphically as curves for the initial water breakthrough recovery, for the different degrees of stratification, as a function of the mobility ratio, and of the composition of the produced fluid stream as a function of the cumulative oil recovery. For several typical cases the latter has also been plotted as a function of the cumulative oil and water throughflow. The general result is that when the mobility of the oil is lower than that of the invading water the channelling tendency resulting from the permeability stratification becomes aggravated as the higher permeability zones become flooded out. Situations of this type would obtain when producing low gravity or highly viscous oils. Conversely, if the mobility of the oil is high compared to that of the invading water, the flooding of the high permeability zones will lead to a retarding and choking effect, and the gross bypassing phenomena will be partially suppressed. These conditions would correspond to those of flooding high gravity or low viscosity oils. A discussion is given of the various basic assumptions made in the analysis, including that of ignoring the stripping phase of the production history as implied by relative permeability concepts. INTRODUCTION The physical ultimate recoveries from oil reservoirs are basically determined and limited by the physical oil displacement processes associated with the reservoir producing mechanism. In practice, however, the economic ultimate recoveries are further limited by the mobility of the reservoir fluids and the uniformity and continuity of the producing formation. In fact, it is the differential depletion between the component parts of the composite reservoir which ultimately determines the total recovery at the time of field abandonment. While this observation applies to both the solution gas drive and gravity drainage mechanisms, in which use is made only of the energy contained within the original oil-bearing reservoir, it is of even more paramount importance under operations wherein the energy associated with extraneous fluids provides the ultimate oil expulsion mechanism. Whether the invading fluid is the water from an edgewater drive, water injected for pressure maintenance, gas injected for pressure maintenance, or gas returned to the formation in a cycling program, it is often the continuity and uniformity of the producing section which will control the economic efficiency of the operations. The importance of the problem of reservoir non-uniformity does not, of course, lessen its complexity or the difficulties of its solution. In fact, these are inherently such that the concept of a "general" solution is virtually meaningless. About all that can be reasonably hoped for is the analysis of specific and well-defined types of non-uniformity which may give some degree of approximation to actual reservoir conditions. Since variations in the nature of the reservoir which depend only on the position along the streamlines will not lead directly to major differential depletion development within the reservoir, the types of non-uniformity considered thus far have involved stratification assumptions. That is, the producing section has been replaced by a multi-layer "sandwich," each uniform areally, and differing from the others only in its basic physical constants as to thickness, porosity and permeability. The fluid motion in the composite system is thus approximated by a parallel superposition of the independent fluid movements in the individual strata. For the specific application to cycling operations the theory of the effect of permeability stratification has been developed for both discontinuous' and continuous types of permeability stratification. Among the latter, treatments have been given of systems in which permeability distributions are governed by exponential, linear' or probability3 functions. In all these studies complete dynamical equivalence was assumed between the injected dry gas and the displaced wet gas. The overall effective permeability of each stratum was therefore considered as constant and independent of the degree of invasion of the injected fluid. In the case of the displacement of oil by water, the assumption of dynamical equivalence between the water and oil will be strictly valid only by accident. Even if the oil viscosity should be the same as that of the water, the effective permeability to the oil in the presence of the connate water will in general be quite different from that of the water behind the water-oil interface flowing past the trapped residual oil. As a result the effective permeability for the stratum as a whole and rate of water invasion will change with time as the intrusion continues. The differential fluid motion in the individual strata will thus also vary with time. Qualitatively, it is easy to predict the resultant effects. If the permeability to viscosity ratio of the invading fluid exceeds that of the fluid displaced, the stratification and bypassing effect of the perme-

Jan 1, 1950

By A. R. Elsea, E. E. Fletcher

This paper describes a metallographic investigation of the influence of tungsten or molybdenum additions upon the transformation and precipitation reactions occurring in Co-rich Co-Cr alloys. It is shown that tungsten has little effect upon the a-ß transformation temperature range, while molybdenum tends to raise it. Both elements tend to promote the formation of ? phase, molybdenum being more potent in this respect than tungsten. HIGH temperature alloys, that is, alloys which have load-carrying ability at elevated temperatures, have been developed at an increasing rate during the past few years. This has resulted from the requirements in the design of modern aircraft engines. Although many alloys of this type are available, they have been developed on an empirical basis. Metallurgists do not have a clear understanding of the phases or structures that are responsible for these high temperature properties. In order to determine why these alloys possess this particular ability, a project was started at Battelle Memorial Institute with the object of learning more about the fundamental factors which promote high temperature strength in alloys. This study was to include a correlation of microstructure and the high temperature properties of Vitallium, an alloy which is widely used for high temperature service. Vitallium is a complex material both from the standpoint of composition and microstructure. Consequently, it was necessary to obtain informa- tion regarding the phase relationships in this alloy. The Co-Cr binary diagram was determined as the first phase of this investigation.' A second paper described the effects of iron, nickel, or nitrogen on the reactions occurring in the Co-rich end of this system.' The present paper covers a continuation of this investigation in which the effects of tungsten or molybdenum on the reactions occurring in Co-rich, Co-Cr-base alloys were determined. Preparation of 'rest Materials Two series of ternary Co-Cr-base alloys, representing Co-Cr ratios of 80:20 and 68:32 ( Cr x 100 =20 and 32 ) , were prepared containing ( Co + Cr = up to 6 pct W and up to 12 pct Mo. Melting stock consisted of electrolytic Co, electrolytic Cr, 99.9 pct pure W, and 99.9 pct pure Mo. Table I lists the chemical analyses of these materials. The melting furnace was a vertical porcelain tube

Jan 1, 1952