Search Documents

By J. L. Walter, W. R. Hibbard

A GREAT deal of work has been done on the rolling of single crystals of iron. Barrett and evensoon studied end orientations of heavily cold-rolled iron crystals and found that some crystals maintained a sharp single orientation during rolling. Others rotated into two or more orientations, and some fragmented and approached the entire polycrystalline texture depending on the original orientation of both the normal and rolling directions. Barrett, Ansel, and Mehl2 studied iron-silicon alloys and found that the addition of silicon to the iron had little effect on heavily rolled polycrystalline material. Dunn3 has extensively studied the cold-rolling and recrystallization of silicon-iron single crystals. Dunn found that for single crystals having initial orientation between (110) [001] and (111) [112], the principalcomponent of the cold-rolled texture is (111) [112]. Koh and Dunn4 studied the cold-rolled textures of single crystals having initial orientations in the range (001) [110] to (111) [IT01 and found that these are stable end orientations. They also found that all orientations having a [110] direction parallel to the transverse direction rotate to either the (001) [110] or the (111) [112] stable end orientation except for orientations near (112) [11], which divide and produce a final texture consisting of (001) [110]and (111) [112] components. Crystals having a (111) <112>-type texture re-crystallized to a (120) [001] or (110) [001]-type texture. Crystals having orientations with a range of (001) to (335) in the rolling plane and [110] in the rolling direction recrystallized5 to a wide spread of the initial orientations resulting from a multiplicity of 30-deg rotations about several (110) poles. The present study was undertaken to relate other orientations of crystals of silicon-iron to their cold-rolling and recrystallization textures, so that one might rationalize polycrystalline recrystallization data on the basis of the known deformation texture and the behavior of single crystals in these orientations. PROCEDURE Samples were obtained from a cylindrical ingot of 3 pct silicon iron prepared as follows: Armco iron was melted with high-purity silicon flakes under an atmosphere of argon to minimize oxidation. The alloy was poured into a special mold to form an ingot which consisted partially of large columnar crystals. Plates were cut from the columnar portions of the ingot with the longitudinal direction parallel to the columnar axes and ground to 0.040 in. thick. The plates were heavily etched to a thickness of 0.032 in. to remove the cold-worked surface. Orientations of seventeen crystals were determined by Laue back-reflection techniques keeping the mean columnar axis as the reference direction. The plate was then cut in two, parallel to the columnar axis. One portion of the plate was rolled at room temperature parallel to the columnar axis to a reduction in thickness of 84 pct. The remaining portion of the plate was rolled also at room temperature across the columnar axis to a reduction of 66 pct, at which point the crystals began to separate at the boundaries. After rolling, nine individual crystals were removed from the strip by cutting along the crystal boundaries with a jeweler&apos;s saw. Fig. 1 shows the original orientations of the six crystals that were straight-rolled and of the three crystals (4, 7, and 8) that were cross-rolled. Each rolled crystal was carefully etched to approximately 0.002 in. thick. Textures of the cold-rolled crystals were determined by use of the diffractometer with a non-integrating sample holder. The pole figures were made for the (200) poles using molybdenum Ka radiation and were plotted by an automatic stereographic projection recorder.&apos; Spurious poles were determined by rerunning portions of the pole figures using strontium oxide to filter out the Ka radiation. The central portions of the pole figures have not been determined. The pole figures were completed to about 55 deg from the periphery at which point the sample holder interfered with passage of the beam. Following the determination of the cold-rolled

Jan 1, 1959

PRESIDENTS DAVID THOMAS 1871 R W RAYMOND 1872-1874 A L HOLLEY1875 ABRAM S HEWITT 1876 T STERRY HUNT 1877 ECKLEY B COXE 1878 - 1879 WILLIAM P SHINN 1880 WILLIAM METCALF 1881 RICHARD P ROTHWELL 1882 ROBERY W HUNT 1883 JAMES C, BAYLES 1884-1885 ROBERT H RICHARDS 1886 THOMAS EGLESTON 1887 WILLIAM B POTTER 1888 RICHARD PEARCE 1889 ADAM S HEWITT 1890 JOHN BIRKINBINE 1891-1892 H M HOWE 1893

Jan 1, 1923

By J. E. Tobey

NATIONAL DEFENSE should not create a dilemma in coal utilization such as obtained during the World War. Even under the heavy pressure of a total preparedness program there should be a smooth flow of the right coals from mines to plants. The more than 100,000 industrial plants of the nation must he served with coal of such characteristics and qualities for their individual requirements that no loss of production due to coal failure shall occur. This problem challenges the ingenuity and cooperativeness of producers. transportation executives, consumers and engineers.

Jan 1, 1941

By J. Szekely, G. P. Martins

A formulation is given for describing the rate of expansion of spherical bubbles rising in liquids the freeboard of which is evacuated. The computer solution of the resultant differential equations has shown that, for low freeboard pressures (less than about 5 mm Hg), on approaching the free surface the bubbles expand much less rapidly than predictable from equilibrium considerations. In other words, in this region the pressure inside the bubbles will be significantly larger than the static pressure in the liquid corresponding to the position of the bubble. These theoretical predictions were confirmed by experimental work, using two-dimensional air bubbles rising in mercury. The important consequence of these findings is that the expansion of gas bubbles in vacuum degassing operations will be a great deal less than expected from hydrostatic considerations. This would lead to a significant reduction in the available interfacial area and may explain the apparent poor efficiency of many vacuum degassing units. VACUUM degassing as a treatment for liquid steel has gained widespread popularity in recent years; the number of known installations exceeds several hundred at the present time.&apos; Although much information is available on both the thermodynamics of the system and the overall performance of various industrial units, much less is known about the fundamental aspects of the process kinetics.2-4 The basic physical situation common to virtually all vacuum degassing operations is the interaction between gas bubbles (swarms of bubbles) and the surrounding molten metal, held in a container, the freeborad of which is at a low absolute pressure. Once formed (or introduced from an external source) the bubbles will ascend, due to the buoyancy forces, and, during this ascent, a significant increase in their volume will occur. This progressive increase in the bubble volume is due to two factors: a) the continuous reduction in the static pressure acting on the bubble during its rise; and b) mass transfer into the bubble from the surrounding molten steel. In a recent paper Richardson and Bradshaw developed equations5 for describing mass transfer into gas bubbles from molten metals at reduced pressures. However, in deriving these expressions it was assumed that the pressure inside the bubble was identical to the static pressure in the adjacent liquid. In other words, the volume of the bubble was considered to be in equilibrium with the pressure of the fluid adjacent to it. This assumption, thus their analysis presented, was thought to be reasonably accurate for most of the bubble&apos;s ascent; however, it was unlikely to be valid in the immediate vicinity of the free surface, held at a low pressure. It was pointed out in the discussion6 that the region close to the surface may be of considerable importance as both the driving force and the interfacial area available for mass transfer are at their highest value here. The &apos; &apos;anomalous" behavior of gas bubbles when approaching a free surface at low pressures was recently confirmed in a preliminary investigation by Szekely and Martins. ?1 Here high-speed motion photography was used to study air bubbles rising in a column of n-tetradecane with a freeboard pressure of 0.1 mm Hg. It was found that significant distortion of the bubbles occurred on approaching the free surface; furthermore, the expansion observed was much less than what one could expect from hydrostatic considerations, i.e., factor a previously discussed. It follows from the foregoing that a detailed study of these phenomena would be justified both from fundamental considerations and because of their potential relevance to technology. The purpose of the paper is to present a more realistic formulation for the expansion of a gas bubble approaching a low-pressure region, together with a comparison of the theoretical prediction with experimental measurement. An inert bubble will be considered in the first instance; it is thought that the understanding of the fluid mechanics is an essential first step toward the realistic formulation of the mass transfer process. This latter problem will be the subject of a subsequent publication. FORMULATION The Physical Model. Consider a spherical bubble, of initial radius Ro, rising in a fluid, having a density pL. Initially let the bubble be at a distance H from the free surface, and at a pressure Pgo, as illustrated in Fig. 1. Pgo, the initial pressure in the bubble, is given by the following equation: pgo = Po = Ptp +pLgH [ la] where Po is the pressure in the liquid corresponding to the initial position of the bubble and Ptp is the pressure at the free surface. The fluid pressure at

Jan 1, 1970

By MARSHALL D. DRAPER

CHINA is one of the large producers of the world&apos;s tin. About 95 per cent of the total Chinese production comes from the Kotchiu district in the southern part of the province of Yunnan. Yunnan occupies the southwestern part of China, bordering on Burma,. Siam and. French Indo-China. From the British port of Hong Kong,&apos; small steamers sail southwest at about four-day intervals, reaching Haiphong in French Indo-China in two or three days. This, one of the principal ports in Indo-China, is a modern French city of some 50,000 population which, with its tropical surroundings, has much natural beauty. It is a few miles from the sea on the Red River, which has its source in China. Both at Haiphong and Hanoi, the capital of Indo-China, sixty-three miles north of Haiphong and also on&apos; the Red River, there are foundries, shipyards, machine shops, cement and brick plants and various similar industries.

Jan 1, 1931

By A. E. Dwight

Lattice parameters were determined for eighteen equiatornic alloys of the CsCl-type structure, ten of which were previously un-reported. It was found that fomation of the CsCl-type structure in binary alloys of the transition elements is largely dependent on position of the elements in the periodic table. The relative size of the two elements was not found to be a controlling factor. A recent paper by Beck, Darby, and Arora1 corre-lates the occurrence of CsC1-type ordered structures with the position of the constituent elements in the periodic table for the first long period. It was also suggested that a definite increase in relative bond strength between unlike atoms occurred when, in binary alloys of iron-group elements, the other component is changed from a chromium-group element, to a vanadium-group element, to titanium. A later paper by Philip and Beck2 noted that the lattice contraction increased in the order CrFe, VFe, and TiFe. It was also noted by Philip and Beck2 that the lattice contractions of CsC1-type alloys decreased in the order: TiFe, TiCo, and TiNi, which is an apparent reversal of the contractions expected from the position in the periodic table. It was suggested that the increasing lattice contraction is an indication of increased stability, i.e., greater A-Bbond strength. The present investigation was carried out to determine whether the relation of the position in the periodic table to the formation of the CsC1-type structure was also correct for alloys involving the second and third long-period elements. A systematic search was made for CsC1-type structures among equiatomic alloys and for those found, the lattice contraction was determined. EXPERIMENTAL TECHNIQUE The elements Y, Gd, Ti, Zr, Hf, V, and Cb are designated the A group and the elements Mn, Re, Fe, Ru, Os, Co, Rh, Ir, Ni, Pd, Pt, Cu, Ag, and Au are designated the B group. Equiatomic alloys were prepared for 57 AB combinations. The alloys were arc melted in a multicrucible furnace3 in buttons ranging from 5 to 20 g. Chemical analyses were not made, as the charge weights agreed closely with those of the buttons after melting. The alloy buttons were homogenized at 800° to 900°C. Metal log raphic and X-ray specimens were prepared and heat treated at temperatures from 600° to 1200°C. Specimens for X-ray diffraction were usually ground to a powder in an agate mortar; however, needle-shaped solid specimens were used when the alloy was sufficiently ductile to permit their preparation. Diffraction patterns were taken with a Straumanistype Debye-Scherrer camera using filtered Cu or Co radiation. The lattice parameters were obtained in A by plotting the calculated a0 values against the cos29/sin 0 + cos2?/? function and extrapolating linearly to ?= 900. Metallographic control specimens were polished on cloth wheels with diamond paste and etched with various phosphoric and nitric acid reagents. RESULTS The eighteen equiatomic alloys listed in Table I gave evidence of a cubic structure with two atoms in the unit cell, although two of these cubic structures exist only at elevated temperatures and transform to a tetragonal structure on quenching. Nine of these eighteen alloys gave diffraction patterns with super-lattice lines showing that the structure is of the CsC1-type. The lack of superlattice lines in patterns of the other nine alloys may be attributed to the small difference in atomic scattering power of the components. Metallographic study indicates the occurrence of nine narrow single-phase fields at the AB composition. Any or all of these nine may also have a CsC1-type structure. The VFe alloy was found to have a CsCl-type structure by Philip and Beck2 through the use of CrKa radiation (for which the scattering factor of V is anomalously low), whereas the Cu radiation used

Jan 1, 1960

By A. E. Nehrenberg

THE mechanism by which austenite forms in steels has received a great deal of attention in the literature in past years.&apos;-&apos;* Our present knowledge concerning this mechanism has been recently summarized quite concisely by Bain and Vilella,1 while a few years ago the literature was carefully reviewed by Roberts and Mehl.² The consensus is that any ferrite-carbide interface is a potential site for the nucleation of austenite during heating above the Acl temperature, and that the new austenite generally grows freely to produce approximately equiaxed grains, whether the carbides are initially present in the lamellar or the spheroidal form. In the case of eutectoid steels, growth of the new grains of austenite continues until contact is established with other grains. Then growth stops and an initial austenite grain size is established which does not change until the heating is continued to some high temperature at which grain coarsening begins. In the case of pearlitic steels which are not of eutectoid composition, the proeutectoid ferrite or carbide may interfere with the growth of the austenite if the temperature is not above that designated the A63 or the Acm, respectively. Although a large amount of work has been done to establish the mechanism of austenite formation in steels, it became clear to the present author while he was studying the transformation characteristics of a new 0.25 C Mn-Si-Ni-Mo hypoeutectoid steel" that the manner in which austenite grows in steels depends upon some factor, or factors, not previously considered. This was indicated by the fact that when this steel in the spheroidized condition was heated above the Ae1 temperature the new austenite which was formed did not envelop the carbides and grow in an equiaxed manner as described by Bain³ or spheroidized steels. Instead, in this steel, the austenite was observed to grow much more readily in certain directions than in others with the result that at temperatures within the Ac1-Ac³ ransformation range the austenite grains were acicular in shape. The excess ferrite was also found to be acicular with the distribution of these phases being such that a lamellar pattern was developed. This unusual directional growth of austenite in this new steel initially in the spheroidized condition is illustrated by fig. 1. A search of the literature revealed that this type of growth was not necessarily peculiar to this steel for similar microstructures had been observed by other investigators.4-8 However, the full significance of these microstructures does not appear to have been appreciated, and no work has been done to determine the conditions responsible for this directional growth of austenite or to arrive at an understanding of it. It was for this purpose that the work described in the present paper was carried out. Material: During the course of this investigation a total of 15 steels was studied. They consisted of hypoeutectoid, eutectoid and hypereutectoid carbon steels, and hypoeutectoid and hypereutectoid alloy steels, all of which were obtained in the annealed condition from commercial warehouse stock. As received, the carbon and alloy hypereutectoid steels had microstructures which consisted of spheroidal carbides in ferrite, whereas the eutectoid steel and the hypoeutectoid steels were pearlitic. The grades of steel represented were 1050, 1080, 10110, 3310, 4140, 4340, 4615, 6145, 8620, 9260, 9442,

Jan 1, 1951

By S. P. Kinney, A. J. Boynton

THIS paper is not the result of recent research with regard to any particular feature of iron metallurgy, blast-furnace practice or mechanical engineering. It is rather a series of notes with regard to contemporaneous progress in blast-furnace construction and operation, together with some suggestions as to changes and improvements that seem to be desirable. On April 1, 1930, a committee of the Chicago District Blast Furnace and Coke Association presented to that association a rather ambitious study of blast-furnace equipment, together with recommendations for the design of construction of a complete blast-furnace unit for the production of 1000 tons of pig iron per day. This report represented the result of months of study by members of the committee, all of whom were actively engaged in operation or design of blast-furnace plants. It is natural, therefore, that comments on the present state of the art should take this 1000-tons furnace, as recommended by the Association, as a basis for comparison with corresponding features of construction or design. See Table 1. In looking through this report at the present time, the significant difference is in the nature of the gas-washing equipment that today would be specified. In other respects, the installation would remain generally very much as it was outlined in 1930. The change in furnace dimensions would be very slight and of no especial significance, except with respect to changes in stock-line diameter, of which more will be said hereafter. The high-efficiency stove as developed by various designers is thoroughly described within this report, and few changes have taken place since. Blowing equipment shows refinement and reflects the improvement in steam engineering. Hoisting and charging equipment and ladles for the conveyance of iron and slag remain, in general, as they were in 1930. In accordance with a general tendency

Jan 1, 1935

By Charles C. Goddard

Since discovery of silver-gold lode deposits in 1864, the Butte district has produced more than $2.25 billion worth of copper, zinc, manganese, silver, and gold, an unprecedented value in the mining world. Exhaustion of the gold placer deposits along Silver Bow Creek, southwest of Butte, forced the early-day placer miners to turn their attention to the bold out- crops of the many veins exposed on the hillsides above the placer diggings. These outcrops bore silver and gold, and enough so that many lode claims were located. Such famous silver mines as the Alice, Moulton, Magna Carta, Nettie, and Blue Bird were developed. These and many smaller operations contributed to making Montana the leading silver-producing state in the 1880&apos;s. As depth was gained in the silver mines in certain parts of the district, occurrence of zinc minerals became troublesome. Zinc was not recoverable at the time, and in the chloridizing, roasting, and amalgamation of the ores, silver and gold recovery was greatly reduced. A period of active silver mining continued until 1892, when a decline in the price of silver brought the silver mining period to a close. Elsewhere in the district it was discovered that while some of the veins contained silver ores in the oxidized portions, the predominant minerals that were deeper were copper-bearing. Marcus Daly exposed rich copper ore on the 300 level of the Anaconda mine in 1891, and mining in the district disclosed that copper was destined to be developed in abundance. Early copper ore shipments were made to Swansea, Wales.

Jan 3, 1959

By S. A. Allison, N. P. Finkelstein

After a brief consideration of the properties of zinc sulfide minerals, their flotation characteristics, and their reactions with thiol collectors, the literature on the activation of the minerals by cupric ion, their deactivation by cyanide, and their depression is reviewed in detail. The distinction between deactivation and depression is stressed. The contradictions in the published results and theories are discussed and attempts are made to resolve them. It is concluded that, whereas all aspects of the subject require further investigation, the study of depression is most likely to yield benefits in practice.

Jan 1, 1976

By AIME AIME

THE 131st meeting of the American Institute of Mining and Metallurgical Engineers was held in New York on Feb. 16 to 20, 1925, with the largest registration of any previous meeting, the total being 1320 compared to 1276 in 1924. The technical sessions were more largely attended and aroused more discussion than ever before. There were joint meetings with the Mining Section of the National Safety Council, under the auspices of the Industrial Relations Committee of the Institute and two very important lectures, the Howe Memorial Lecture, under the auspices of the Iron and Steel Committee, and the lecture by Dr. Carl Benedicks, of Sweden, on Corrosion, under the auspices of the Institute of Metals Division. The Petroleum Division conducted its annual Symposium on Oil which will be published later in book form. At the annual business meeting on Feb. 17, the following ticket was elected, and the reports of the President, Treasurer, and Secretary &apos;were presented:

Jan 1, 1925

By Oliver C., Ralston

THE following data were obtained during Tan exhaustive research into the possibilities of concentrating United Verde massive sulfide copper-zinc-iron ores by flotation. The composition of these ores approximates the following mineralogical analysis: 3 to 15 per cent chalcopyrite; 3 to 11 per cent marmatite (ferruginous sphalerite) ; 47 to 69 per cent pyrite; and 10 per cent quartz. The remainder is usually schist gangue. The sulfide minerals are finely dis-seminated; chalcopvrite and marmatite begin to be liberated on grinding at about 100 mesh, but complete liberation from gangue (pyrite in this case is considered a gangue mineral) is

Jan 1, 1935

By J. L. Bruce

After six years of war-enforced idleness, Cyprus copper mines are operating again. This relatively long shutdown seems infinitesimal when compared with something like seventeen hundred years of inactivity that followed the important operations of the ancient Romans, and continued until the twentieth century. The historical records of the ancient operators are scarce but full of interest to those who realize that Cyprus copper production was important more than two thousand years ago. This paper, however, will give only a brief review of the ancient history and the evidence of ancient mining which have been quite fully covered in other publications.1-6 The purpose of this paper is to give a general sketch of the Cyprus Mines Corporation&apos;s enterprise in the Island of Cyprus, with special emphasis on those conditions and practices which are unusual. The picture is not intended to be complete, and many interesting details will be omitted. Some of these may be described in subsequent papers covering departmental practices. The principal operations of Cyprus Mines Corp. are in Cyprus, where it has leasehold concessions from the Cyprus Government covering about 50 square miles. It holds additional areas under "Prospecting Permits." The consideration for the concessions is a royalty on production, coupled with minimum annual rentals. Cyprus is a British Colony in the Eastern end of the Mediterranean with an area of about 3000 square miles and a population of about 400,000, of which 65 pct may be classed as Greeks on the basis of language, religious training, and traditions. About 25 pct are Moslems, principally of Turkish extraction. Prevailing languages are Greek and Turkish. A large proportion of the supervisory and administrative staff and practically all of the skilled and unskilled craftsmen and laborers are drawn from the native population. The "overseas" staff constitutes not more than 2 pct of the employees. The majority of these are from the United Kingdom, the British Dominions and Colonies. About one-third are from the United States of America. The topography of the Island is rugged, with mountains and foothills covering more than two-thirds of the area. Between the Kyrenea range rising to 3000-ft elevation, along the north coast, and the Troodos range (maximum elevation 6400 ft) occupying the southwest half of the Island, lies a cultivated rolling plain, the "Mesaoria," dry in summer and watered only by the winter rains and by scanty irrigation from small mountain streams and wells in the spring and summer. Climate and natural vegetation are characteristic of semi-arid conditions. The "urban" population, about one-fourth of the total, lives in the five port towns, Famagusta, Larnaca, Limassol, Paphos and Kyrenia, and in the capitol Nicosia, near the center of the Island. The suburban population lives almost entirely in villages or small towns, with very few people residing in isolated country homes.

Jan 1, 1949

By Frederic Dewey

BONE-ASH cupels have been used from time immemorial to absorb litharge, and accompanying oxides; in assaying. Doubtless, also, from the earliest days cupels have been most unjustly blamed for much poor assaying. It has long been known that the precious metals go with the litharge into the cupel. This occasions a loss of precious metals and reduces the results of the assay. There have been many investigations of cupels and the most diverse views have been expressed, the extremes being the statements of Lodge 1 that every cupel has some effect upon the loss in assaying telluride ores and of the Campredons2 that coarse and fine and hard and soft cupels all give the same loss of silver when cupelling the same weights. The truth lies between these statements and much nearer the latter. In a vast majority of cases the influence of the cupel is not dominant and is outweighed by other conditions, particularly the temperature of the cupelling bead. At the Spokane meeting of the Institute I presented a paper on the Assay and Valuation of Gold Bullion,3 which recorded the results of many hundreds of assays made in the Mint service under everyday commercial conditions, which of necessity differ from scientific conditions. In following this matter up, for the purpose of increasing the accuracy of our commercial methods of bullion assays, the question of the absorption of gold by the cupel was found to be a most important one and was taken up for investigation. In a lesser degree, the silver absorption is important and interesting, but at present it appears to be far more complicated and, while many figures showing silver absorption may be found through this paper, much further investigation is required to put the subject upon a satisfactory basis.

Jan 11, 1917

By D. C. Hilty, W. Crafts

J. Chipman—It has been my privilege to discuss this work with the authors on several occasions and to observe at first hand the experimental methods employed. I wish, therefore, to emphasize certain points which they have mentioned only briefly with regard to the experimental techniques. The rotating induction furnace as here employed interposes liquid metal between slag and refractory thus preventing the two nonmetallic parts of the system from reaching equilibrium with one another. It is therefore impossible for the metallic phase to be completely in equilibrium with both the slag and the crucible. The metal also acts as a partially permeable membrane allowing certain components, including oxygen, to diffuse from slag to crucible. This transfer results in building up on the face of the crucible a layer of material whose composition is in part dependent on that of the bath. Reactions between the layer and the solid refractory are slow, as evidenced by the rather good life of the crucible. Hence it seems probable that the layer is more nearly in equilibrium with the metal than with the underlying crucible material and that, once it is established under a bath of a given composition, its further reactions with that bath are slow. Additions to slag or bath may be followed by changes in the layer; and time must be allowed for virtual completion of such changes, before it can be assumed that slag and metal are in equilibrium. We may judge from the results reported that, in general, this was the case and that the data represent at least quite close approximations to slag-metal equilibrium. Data on deoxidation and on oxygen solubility are no better than the analytical methods employed. The vacuum fusion method as used by the authors seems entirely adequate for the samples analyzed. I have had frequent occasion to compare results with their laboratory, always with very satisfactory agreement. The determination of aluminum at very low concentrations is perhaps an even more difficult procedure. Here also the colorimetric method used has been worked out with great care and is undoubtedly the most dependable method available. The discrepancy between observed and calculated deoxidation or solubility lines is not to be explained as the result of experimental errors, either in the sampling or analysis of the metal. Nor is it to be blamed upon inaccuracies in the several kinds of indirect data upon which the calculated results were based. It is true that both the observed and the calculated lines admit of some uncertainty as to their exact locations, but the uncertainties are small compared to the wide gap which separates the two lines. The authors have pointed out the real cause of the discrepancy. In all of their experiments the solid phase was not Al2O3 but a mixed oxide containing iron and aluminum. This suggests an extension of the calculated values to include equilibrium with the spinel FeO . A12O3. The free energies of FeO and A12O3 are known, that of the spinel is not. However, it cannot differ greatly from that of its component oxides for even in the more stable spinel, chromite, the free energy of formation from the oxides is less than 10,000 cal. For purposes of calculation we shall call this free energy X and solve for values of X lying between zero and 10,000 cal. The other data required are taken from the forthcoming revision of "Basic Open Hearth Steelmaking" and are given in the following equations in which underlined symbols indicate elements dissolved in liquid steel and the standard concentrations are 1 pct. ?F° at 1600°C, cal ?LA = 2 Al + 3 O; + 107,200 FeO = Fe + 0; + 5,460 FeO + A12O3 = Fe + 2A1 + 4 0; + 112,660 — X The corresponding equilibrium concentrations are shown in fig. 21. The line marked A12O3 corresponds to the first equation, those marked FeO . AL2O3 correspond to the last, with X = 0, 5000 and 10,000 cal, respectively. The two upper lines represent the data of Hilty and Crafts and of Wentrup and Hieber. The points are the observations of Hilty and Crafts in the presence of 0.50 pct Mn.

Jan 1, 1951

By T. L. Loucks, E. T. Guerrero

Pressure drop characteristics in a system composed of two adjacent concentric regions of different permeability were studied. The differential equations for continuity of mass flow in the two regions were solved using the Laplace transformation and the necessary boundary conditions to give the pressure distribution in the composite reservoir, the resulting equation for pressure drop at the inner boundary was evaluated for a variety of composite reservoirs and compared with the results for a uniform reservoir. From this study it was found that under certain conditions the permeability in both zones, as well as the size of the inner zone, can be determined from the pressure drop curve. INTRODUCTION The theory for the pressure distribution and pressure build-up behavior of a well producing a single, slightly compressible fluid from infinite and finite homogeneous reservoirs was presented by Hornerl and Miller, Dyes and Hutchinson.2 Extensions on this original work to provide improved and extended interpretations and better agreement between theory and observed results have been made by Matthews, et a1,3 van Everdingen,4 Gladfelter, et al5 Stegemeierand Matthews,6 Hurst and Guerrero,7 and Perrine.8 More recently Lefkovits, et al,9 studied pressure build-up behavior in bounded reservoirs composed of stratified layers. Houpeurtl0 has suggested various approaches to the general problem of variable permeability and porosity but presented no analytic solutions for particular permeability variations. Albert, Jaisson and Marionll studied the finite composite reservoir and presented numerical solutions to the unsteady-state case and an analytical solution valid only for large times. They also studied the so-called pseudo-steady state for several examples of radial permeability variations. Very similar examples have been treated in the unsteady state with application to pressure build-up by Loucks in an unpublished manuscript. More recently Hurst12 has presented the complete point-sink solution (valid for all times) for the infinite composite reservoir. He applied these solutions to interference between oil fields along with an even more elegant application of his explicit solution to the material-balance equation including water influx. Mortada 13 approaches the same application by avoiding the point-source limitation but gives the solution for the aquifer region which is valid only for large times. Hopkinson, Natanson and Temple14 have treated both the finite and infinite composite reservoir obtaining the pressure distribution for the inner zone valid for large times. This paper presents a theoretical study of the pressure distribution in an infinite composite reservoir composed of two adjacent concentric regions of different permeability. The object was to determine the manner in which pressure drop at the inner boundary of a composite reservoir depends upon time, the permeability of each zone and the size of the inner zone. Expressions for the pressure distribution in both zones are developed which take into account the radius of the sink and are valid for small times as well as large times. It was felt that an understanding of the pressure drop behavior in various composite reservoirs would be of assistance in the interpretation of some pressure build-up curves which do not behave according to the theory derived for uniform systems. Often the region surrounding the wellbore is either more permeable or less permeable than the reservoir because of the various drilling and completion practices. The effects of reduced permeability due to drilling-fluid invasion and of increased permeability due to fracturing or acidizing need to be more carefully defined. Therefore, an equation for the pressure drop in a composite reservoir was developed, and the effects of both the permeability in each zone and the size of the inner zone were studied. STATEMENT AND SOLUTION OF PROBLEM BOUNDARY CONDITIONS AND ASSUMPTIONS The physical system studied was a composite

By H. Kazemi

An ideal theoretical model of a naturally fractured reservoir with a uniform fracture distribution, motivated by an earlier model by Warren and Root, has been developed. This model consists of a finite circular reservoir with a centrally located well and two distinct porous regions, referred to as matrix and fracture, respectively. The matrix has high storage, but low flow capacity; the fracture has low storage, but high flow capacity. The flow in the entire reservoir is unsteady state. The results of this study are compared with the results of the earlier models, and it has been concluded that major conclusions of Warren and Root are quite substantial. Furthermore, an attempt has been made to study critically other analytical methods reported in the literature. In general, it may be concluded that the analysis of a naturally fractured reservoir from pressure transient data relies considerably on the degree and the type of heterogeneity of the system; the testing procedure and test facilities are sometimes as important. Nevertheless, under favorable conditions, one should be able to calculate in-situ characteristics of the matrix-fracture system, such as pore-volume ratio, over-all capacity of the formation, total storage capacity of the porous matrix, and some measure of matrix permeability. INTRODUCTION The analysis of flow and buildup tests for obtaining in-situ characteristics of oil and gas reservoirs has received considerable attention in the past decade. Most of the available techniques result in reliable conclusions in macroscopically homogeneous reservoirs or in the homogeneous reservoirs with only certain types of induced and/or inherent heterogeneity (such as wellbore damage, etc.). In general, the greater the degree of heterogeneity, the less the reliability of the information deduced from the pressure transient data. A commonly encountered heterogeneous system is a naturally fractured reservoir where two types of distinct porosities occur in the same formation. The region containing finer pores may have high storage and low flow capacities. This is called the matrix. The remaining region may have high flow capacity with low storage. The latter region is generally the set of interconnecting fractures and fissures of the rock, and for this reason it is called the fracture. Ordinarily, we wish to obtain the permeability and porosity of each region and perhaps the frequency of the fracture distribution in a reservoir. Such information is necessary for reservoir engineering. Other information, such as wellbore damage, will be useful in evaluating possible remedial work for such fields. Few authors have suggested theories to aid in calculating the in-situ characteristics of a naturally fractured reservoir similar to what we have described above. Pollardl suggested that a naturally fractured reservoir contained three distinct regions: a damaged or an improved region surrounding the wellbore, and the two remaining regions the same as described earlier. He suggested that the flow was taking place from the tight matrix into the highly conductive fractures, then into the we wllbore region and finally into the well column. He concluded that the average pressure buildup in each of these distinct regions can be expressed approximately in terms of an exponential decay function of time. He also hypothesized that the decay coefficients for each of these functions were significantly different from each other; consequently, each of these functions became dominant in turn, in the process of pressure buildup. Thus, by a proper graphic plot of the logarithm of wellbore pressure differences vs buildup time, each of these functions could be determined (see Fig. 1). Pollard suggested methods of determining the wellbore damage and fracture volume. Later Pirson and Pirson2 extended

Jan 1, 1970

By Charles Fettke

IN THE present day manufacture of glass nearly pure quartz sands are used almost exclusively as the source of the silica, which is the major constituent of all common varieties of glass. Ordinary soda-lime, such as bottle, common tableware, plate, and window glasses, contain from 65 to 75 per cent. of silica. OCCURRENCE Glass sands occur in nature either in the form of loose, unconsolidated sediments or in deposits in which the individual grains have been more or less thoroughly bound together by some cementing agent so as to form sandstones. While deposits of sand and sandstones occur both widely and abundantly distributed, deposits that are sufficiently free from other constituents than quartz grains, so that they can be employed in the manufacture of the better grades of glass, are, comparatively speaking, of rare occurrence. The major portion of the glass sand produced in the United States comes from sandstones. In order to be suitable for glass sand, they should be rather friable. The rock should break down readily along the cementing material between the grains and should not break across the grains rather than along the bond. Some of the sandstones used are so friable that only light shots of slow-burning dynamite are necessary to disintegrate them sufficiently for hydraulic mining, while others have to be passed through crushers in order to disintegrate the rock into its individual grains.

Jan 2, 1926

By J. A. Elias, A. J. Heckler

A simplified method is described for the prepauatior~ of comnposite samples for determination of one quadrant of an X-ray pole figure of a sheet material by the Schulz reflection method. Other special conzposite sampling methods were used to investigate specific areas of the pole figures. Plotting nets for these sampling plans were drawn by a computer. Step-scanning techniques were used to obtain detailed information about specific regions of a pole figure. Satisfactory pole figures were obtained for large-grained (0.5 to 1 in. diam) sheet materials. COMPOSITE sampling techniques for preparing one quadrant of an X-ray pole figure have been reported by a number of authors.&apos;-5 All of these methods are similar in that they use a composite sample prepared by stacking and holding together coupons cut from a sheet material. The schulze reflection technique is applicable to the composite sample so that only minor corrections are needed for defocusing and absorption effects. Also, a relatively large area of a sheet is sampled through the use of multiple cross sectional pieces. In general, sampling methods necessary to obtain a composite-type specimen have been formidable enough to discourage their use in routine pole figure determinations. This paper presents a versatile sampling technique which is simpler than those previously described along with an accurate method for obtaining stereographic plotting nets for any orientation of a composite specimen surface. A step-scanning technique is used to obtain more quantitative determinations of specific regions in pole figures, and the composite technique is satisfactorily applied to determine pole figures of very large grained sheet materials. REVIEW OF PREVIOUS TECHNIQUES Mueller and ~nott&apos; first proposed a technique for obtaining one complete quadrant of an X-ray pole figure by using a sheet sample and six different composite samples in which the individual coupons were aligned and held together by two types of jigs. Data from the seven different samples were overlapped to obtain a single quadrant. ~eieran~ and Lopata and ~ula~ obtained a complete quadrant of a pole figure from a single sample prepared by forming a cube from coupons cut from a sheet. These coupons were bonded together using an epoxy cement, and a cut was made at 54.7 deg to the normal, transverse, and rolling directions of the sheet, Fig. I. The normal direction of the cut face projects into one quadrant of a stereographic projection at equal angles to the three principal orthogonal reference directions mentioned above. X-ray reflection data obtained along a spiral path in physical space could then be plotted on a stereographic net offset 54.7 deg from the normal, as shown in Fig. 2. A rotation about an axis representing the surface normal is designated as a, and a rotation about an axis lying in the plane of the surface is 4. From Fig. 2 it is apparent that a tilting angle of no more than 55 deg @ is necessary to obtain the complete quadrant. ~eber~ devised an improved sampling technique by cutting coupons 45 deg to the rolling direction of a sheet, stacking and bonding these with an epoxy cement at an angle of 54.7 deg to a reference plane, and finally grinding and lapping a flat specimen surface parallel to this plane. An important consideration of this technique and that of Lopata and ~ula~ is variation in the diffracting power of the specimen surface due to the bonding medium. While any composite-type sample will have some such variation due to boundaries between coupons, the problem can be minimized by elimination of the bonding medium and by avoiding prolonged etching times which could lead to significant inter lame llar attack of the coupon faces. EXPERIMENTAL TECHNIQUE We were working concurrently though independently on a technique similar to ~eber&apos;s,&apos; but which does not

Jan 1, 1968

By Clarence P. Linville

(Pittsburg Meeting, March, 1910.) IT is recognized that, in all metallurgical operations, the greatest possible uniformity in all conditions is essential to the best results. It is the constant aim of metallurgists to secure this uniformity, and their success in this respect has been in many cases the cause of great advances in the metallurgical processes themselves. Of all such processes, the production of pig-iron in the modern blast-furnace is perhaps the most complex and the most difficult of control. Notwithstanding the great progress of recent years, there is still great difficulty in obtaining anything like uniform conditions and results in the manufacture of pig-iron. The reason is not far to seek. The ores vary in composition and physical properties, often carrying a varying amount of gangue material, unevenly distributed The coke may vary in composition, cell-structure, moisture, hardness, and other properties. The blast, the weight of which far exceeds that of any other constituent, varies in its moisture-content and consequently in its chemical composition ; and its temperature, by reason of the method of heating, is not uniform, but, besides varying from time to time with atmospheric and other outside conditions, has a maximum and minimum for every changing of stoves. Now, with regard to these variations, the modern demand for uniformity has been greatly aided. Chemical analysis has made it possible to select ores so that the composition of the charge can be kept fairly constant; coal may be obtained from a given field, and coked in the same kind of ovens under conditions which . make the fuel practically uniform ; the Gayley

Mar 1, 1910