Search Documents

[NORTH AMERICA ALASKA Anchorage.-Strandberg, H. Chlchagoff.-Russell, J. C. College.-Barber. R. J. Dorsh, J. B. Fox, E. F. Joesting, H. R. McAnerney, J., M. Douglas.-Cahill, W. E. Fairbanks.-Beistline, E. H. Crawford, J. D. Earling, R. B. Greves, J. H. Harris, Q. P., Jr. Henton, H. M. Herbert, C. F. Hester. W. B. Hopkins, J. E. Kreitlow, E. J. MacDonald, D., III March, J. P. Mathews, T. C.]

Jan 1, 1940

By F. E. Pawlek, J. K. Gerlach

The chloridizing roasting of ores is applied when metal sulfides and oxides are to be converted into soluble or volatile compounds. The chlorine required is either obtained from the admixed chlorides of sodium or calcium or added in the gaseous state. In the first part of the investigations the reaction rate of the chlorides of sodium or calcium with gas mixtures of SO,-0, or SO ,-O2 ,-SO , was measured. The rate for reactions with gas mixtures SO2-O2 is ThE chloridizing roasting of ores is applied when metal sulfides and oxides are to be converted into soluble or volatile compounds. At present the process is mainly applied to produce nonferrous metals which occur in pyrite cinders in small concentrations. Thereby the nonferrous metals are converted into water-soluble, acid-soluble, or volatile compounds whereas all the iron remains as insoluble oxide. The chlorine required is either obtained from the admixed chlorides of sodium or calcium or added in the gaseous state. The reactions occurring during the roasting process can be divided into two groups: solid-solid reaction and gas-solid reaction. The reactions between solids proceed by means of solid-state diffusion and are therefore of low velocity. The heterogeneous reactions between solids and gases of the roasting atmosphere5 are high-velocity processes and determine the velocity of the chloridizing roasting. These gas-solid reactions shall be the subject of the paper presented. In order to investigate the still little-known processes which occur during the chloridizing roasting 6-' the complex reaction is split into several partial steps. First the reactions of NaCl and CaCl, with gas mixtures of SO2 and 0, have been investigated at temperatures between 500" and 600°C by measuring the weight increase of the samples. The gas mixtures used in this series of experiments had first variable compositions, then the amount of SO 2 had been increased. Furthermore the influence of Fe 2 O3 admixtures upon these reactions, the behavior of pure Fe 2 O3 with the gaseous reactants, and the chlorination of the sulfides of lead, copper, nickel, and zinc have been investigated. FORMATION OF GASEOUS CHLORINE Pyrite cinders are never completely roasted and therefore contain still a small amount of sulfide sulfur. When heated again in air, this sulfur is converted into SO,. Accordingly the formation of chlorine can first be described by the reactions: dependent on the composition of the gas phase. If more than 1 pct SO 3 is added to the roasting gas, the reaction rate is determined only by the concentrations of the SO,. In the second part the reactions between chlorine and metal sulfides are discussed. The rate of formation of gaseous chlorine is higher by me order of magnitude than is the reaction rate between ZnS and chlorine. The reaction rate of NiS and PbS lies considerably below that of ZnS. The conversion rate of both pure Fe 2 O 3 and Fe 2 O 3 containing NaCl or CaCl2 when reacting with SO2-O2, mixtures with and without SO3 portions was measured at temperatures of 500", 550°, and 600°C. The weight increase of pressings was determined by means of a spiral balanceg and the reaction rate calculated therefrom according to Eqs. [ll to [31 and [5] to [7]. The prepared samples were suspended on a platinum filament in a vertically mounted tube of mullite (ID 4 cm, length 110 cm) which could be heated by a resistance tube furnace. The platinum filament was tied to the lower end of the spiral balance. A supremax glass tube (length 70 cm) was mounted gas-tight on top of the reaction tube. The unit was sealed up at its top by a ground-in stopper which was holding the spiral balance with the sample. The spiral balance therefore hung outside the high-temperature region of the furnace. Fig. 2 shows the experimental arrangement schematically. While lowering the sample into the reaction tube pure nitrogen was flowing through the reaction zone providing a protective atmosphere. After the sample had reached the reaction temperature within approximately 1 min, the protective gas was replaced by the sulfur dioxide-oxygen reaction mixture. It took about 30 sec until the mixture filled the tube homogeneously. A Ni/NiCr thermocouple placed in the center of the furnace where the sample hung during the measure-

Jan 1, 1968

By H. E. Exner

This article is a critical review of the influence of surface preparation on crack formation at Vickers indentations in the test used by Palmqvist3-7 to evaluate the toughness of cemented carbides. Experimental results are presented which clearly show that grinding introduces compressive surface stresses into the cobalt phase and thus reduces the crack length. The deformed surface layer is removed by polishing and a stress pattern is approached corresponding to that in the bulk material. Cracks of maximum length are characteristic of this stress state. Deformation stresses can be removed by annealing above 800°C. On the basis of these results , sample preparation for the crack length test can be simplified, the accuracy of measurement is improved, and a simple and significani parameter is found to describe crack resistance of cemented carbides. FOLLOWING suggestions by Ammann and Hinniiber,1'2 Palmqvist3-7 developed a method for testing the toughness of cemented carbides using as a measure the sum of crack lengths at the four corners of a Vickers hardness indentation. This method has several advantages over the bend test commonly used in carbide technology: a) specially formed samples are unnecessary; b) sufficient information can be obtained from one sample; c) the scatter is relatively small; d) the range of actual values for commercial cutting alloys is wide. Thus, this test is both cheaper and more precise than the bend test. Nevertheless, Palmqvist's method is not widely used, mainly for two reasons: a) The relationship between crack length and the technological properties of the material (wear and shock resistance) is not clear. b) The crack length is strongly dependent on surface treatment. It is necessary, therefore, that surface preparation be very precise and reproducible, conditions usually hard to obtain. While any other simple mechanical test has this first drawback, the second became crucial in the application of the crack length method as a practical test. The reasons that this drawback could not be eliminated are, in our opinion, misleading and inconsistent interpretations of the influence of surface preparation on the crack length given in literature. In the following, after a short review of previous experimental results the interpretations given by different authors,4?'-11 cf. Table I, are discussed critically and a consistent explanation is presented on the basis of which improvements of the method of crack length testing are proposed. 1) PREVIOUS EXPERIMENTAL RESULTS In his first attempt to use the cracks at Vickers impressions as a quantitative measure of the toughness of cemented carbides, palmqvist3 calculated the work necessary to initiate cracks by the formula: Sk =k.Pk. [I] where k = numerical constant = 6.49, Sk = critical work to initiate cracks (gf cm), Pk = critical load (load necessary to initiate cracks) HV = Vickers hardness (kp per sq mm). The difficulties involved in experimental determination of the critical load were overcome by the observation that a linear relation holds between the applied load and the sum of the crack lengths at the four corners of the indentation. This linear function, given by Eq. [2] below, was confirmed by Dawihl and Alt-meyer9and by our experiments, see Fig. 1: I = a1.P +a2 [2] where 1 = sum of the crack lengths at a Vickers indentation, P = applied load, al, a2 = parameters dependent on the toughness of the alloy and the surface preparation. The critical load, Pk, is now given by a2, which can be obtained by extrapolating the load vs crack length line to zero crack length, see Fig. 1. This simple relationship, Eq. [2], led Palmqvist1,7 to a parameter which was more reproducible and easier to obtain experimentally than the critical work: the work, S300, put into the sample to produce an average crack length of 300 µm per indentation. This parameter is calculated using the formula: where the load, P3oo, giving a crack length of 300 µm, can be taken from the load-crack length plot, Fig. 1,

Jan 1, 1970

By Peter Tegart

The discovery of gold in the Toodoggone River area is credited to Charles McClair who mined placer deposits in 1925, reportedly valued at $17,500. After he and his partner went missing in 1927, efforts to relocate their workings resulted in the formation of Two Brothers Valley Gold Mines Ltd. in 1933, in which the legendary Grant McConachie (first president of CP Air) played an active role. This was the age when the prospector first utilized the airplane to reconnoitre remote areas. What greeted the observer from the air was an area rich in orange and yellow colours characteristic of gossans formed by the oxidation of sulphides. However, Samuel Black, a Hudson Bay Company fur trader, had also noted in his diary as early as 1824, the unusual and many gossanous colours in the headwaters of the Finlay River. These gossans, coupled with white limestone bluffs and the presence of placer gold, attracted the first reconnaissance of the area by Cominco in 1929. Cominco was ever active in remote areas at this time. They staked and worked several base-metal showings hosted by limestone at the margins of intrusive stocks. These early workers also obtained erratic high gold assays from chalcedony float samples found in creeks draining into the Toodoggone River. However, because the samples gave inconsistent assays, no concerted effort was made to locate their source. Except for the occasional horse-supported prospecting party of the late 1940s and early 1950s, the area did not receive much attention until 1968. Work until this time focused on the base metal lead-zinc showings which contained attractive silver credits. Gold was not an attraction because of the set price established by the US government. The late 1960s saw the northward expansion of porphyry copper exploration into the Toodoggone. A program of gossan soil sampling (gossans which had attracted the early workers) was carried out by Kennco Explorations (Western) Ltd. in 1966-1967. They analysed for base metals in the field, using a cold extraction method. The Kemess copper- gold prospect was staked as a result of anomalous copper values from this early geochemical program. In 1968, Kennco continued the program of silt traversing and field geochemical testing. The samples were further subjected to multielement analysis consisting of copper, molybdenum, lead, zinc, cobalt, nickel, and silver at Kennco's North Vancouver laboratory. Several anomalous creeks, high in combinations of copper, molybdenum, and silver, were outlined. Some initial soil grids were also established. The fall of 1969 saw the return of Kennco prospector Gordon Davies and geologist Bob Stevenson to check out a well-defined molybdenum, scattered copper and silver anomaly in soils from a grid on the Chappelle claims. The subsequent analysis of several selected quartz felsenmeer floats yielded one assay which ran in the order of 0.25 kg/t (8 oz per st) gold and 2.2 kg/t (70 oz per st) silver. Subsequent trenching on the Chappelle claims exposed the source of float in a 4- m (134) wide vein of high grade gold-silver mineralization. These results led quickly to the realization that the district had precious metal potential. Subsequent exploration in the period 1969-1974 by Kennco resulted in the discovery of most of the gold and silver occurrences on the Chappelle and Lawyers properties. Several other gold and silver occurrences were found in this district by Cordilleran, Cominco, and Sumitomo, working the district during this period. Conwest optioned the Chappelle in 1973 and explored underground by adit entry as part of a one-year program. In 1974, Du Pont of Canada Exploration Ltd. optioned the Chappelle claims and in March 1980, using reserves developed on the A vein, placed the Baker mine into production at a rate of 90.7 Vd (100 stpd). The Amethyst zone on the Lawyers property, 8 km (5 miles) north of Chappelle, was found in 1973 by Kennco using continued, persistent followup prospecting of silver silt geochemical anomalies. A silt anomaly in the order of 3.4 ppm silver occurred in a stream flowing 300 m (984 ft)

Jan 1, 1985

By A. H. Geisler, R. F. Mehl, C. S. Barrett

The mechanism by which the supersaturated solid solution of 20 per cent silver in aluminum decomposes has been reported in two previous publications.1'2 The analysis of streaks in Laue photograms showed that thin platelike particles (the so-called Guinier-Preston aggregates) form upon matrix planes in the early state of decomposition.1 The size of these particles is larger, the higher the temperature at which they form in accordance with nucleation theory;³ at all temperatures they increase in size with aging.2 When they have grown thick enough to afford three-dimensional diffraction, powder X-ray photograms show that the structure is not that of the equilibrium precipitate but that of a transition lattice . Sincc this is also platelike in shape and also lies upon the (III) matrix planes with the [IIO] direction in the matrix parallel to the [II.O] direction in it seems likely that the original platelet particles are merely in an early stage of formation, and thus finely dispersed. The atomic spacing and pattern on the (00.1) plane in y' are identical with those on the (111) matrix plane to which it lies parallel, and since comparable directions in the two planes are parallel, the lattices are thus coherent at the interface; an analogous coherence has been found in aluminum-copper alloys.3 The structures y' and y are both close-packed hexagonal and are oriented alike; they differ only in interatomic distances. Consequently, y' is regarded as y strained from its ordinary dimensions by the lattice coherency between it and the matrix.2 The lattice movements that transform the matrix to the equilibrium precipitate appear to be very simple.2 The mechanism of precipitation in this system is simpler and is more precisely known than that in any other system hence the system should be a profitable one for the difficult task of correlating property changes with structural alterations. The present report provides additional studies on powder X-ray diffraction from alloys of 10 per cent, 20 per cent and 30 per cent Ag, and presents the correlation of crystallographic changes with changes in microstructurc, Brinell hardness and electrical resistivity of the three alloys. Preparation of Samples and Experimental Procedure The preparation of the 20.2 per cent Ag alloy has been described2 Alloys containing 9.9 and 29.7 per cent Ag were prepared from 99.97 per cent A1 and 99.99+ per cent Ag using a similar procedure. Rolled

Jan 1, 1943

By R. F. Mehl, C. S. Barrett, A. H. Geisler

The mechanism by which the supersaturated solid solution of 20 per cent silver in aluminum decomposes has been reported in two previous publications.1'2 The analysis of streaks in Laue photograms showed that thin platelike particles (the so-called Guinier-Preston aggregates) form upon matrix planes in the early state of decomposition.1 The size of these particles is larger, the higher the temperature at which they form in accordance with nucleation theory;³ at all temperatures they increase in size with aging.2 When they have grown thick enough to afford three-dimensional diffraction, powder X-ray photograms show that the structure is not that of the equilibrium precipitate but that of a transition lattice . Sincc this is also platelike in shape and also lies upon the (III) matrix planes with the [IIO] direction in the matrix parallel to the [II.O] direction in it seems likely that the original platelet particles are merely in an early stage of formation, and thus finely dispersed. The atomic spacing and pattern on the (00.1) plane in y' are identical with those on the (111) matrix plane to which it lies parallel, and since comparable directions in the two planes are parallel, the lattices are thus coherent at the interface; an analogous coherence has been found in aluminum-copper alloys.3 The structures y' and y are both close-packed hexagonal and are oriented alike; they differ only in interatomic distances. Consequently, y' is regarded as y strained from its ordinary dimensions by the lattice coherency between it and the matrix.2 The lattice movements that transform the matrix to the equilibrium precipitate appear to be very simple.2 The mechanism of precipitation in this system is simpler and is more precisely known than that in any other system hence the system should be a profitable one for the difficult task of correlating property changes with structural alterations. The present report provides additional studies on powder X-ray diffraction from alloys of 10 per cent, 20 per cent and 30 per cent Ag, and presents the correlation of crystallographic changes with changes in microstructurc, Brinell hardness and electrical resistivity of the three alloys. Preparation of Samples and Experimental Procedure The preparation of the 20.2 per cent Ag alloy has been described2 Alloys containing 9.9 and 29.7 per cent Ag were prepared from 99.97 per cent A1 and 99.99+ per cent Ag using a similar procedure. Rolled

Jan 1, 1943

By B. N. Bose, M. F. Hawk

SINCE Davenport and Bain' introduced the isothermal transformation technique for the study of austenite decomposition in steels, a new field of investigation has opened up. Extensive research has been carried out on many different steels, but relatively little work has been done on eutectoid transformations in analogous alloy systems. The researches of Smith and Lindlief,² Mack,³ and Klier and Grymko²0 on the beta-phase transformation in copper-aluminum alloys, of Hibbard, Eichelrnan, and Saunders4 and Smith5 on the kappa-phase transformation in copper-silicon alloys, of Chaudron and Forester6 on the decomposition of "FeO," and of Wasserman7 on similarities between the iron-carbon, copper-aluminum, copper-tin, and copper-beryllium systems essentially comprise the field. The iron-nitrogen system, in view of its remarkable similarity to the iron-carbon system, is particularly attractive for the study of eutectoid decomposition. The present investigation is concerned with the study of isothermal transformation, proceeding by the familiar nucleation and growth processes, and of martensitic transformation characteristics of pure iron-nitrogen alloys. The kinetics of transformation and the morphology of the transformation products have been investigated, for these must be the factors determining the properties and behavior of the final product. The Iron-Nitrogen System he binary iron-nitrogen phase diagram has been a matter of considerable disagreement among vari01.1s investigators. However, the phase diagram according to Eisenhut and Kaupp8 and Lehrer10 is now considered essentially correct as reproduced in fig. 1. The important values, 2.35 pct nitrogen and 591°C, for the co-ordinates of the eutectoid point (obtained from this diagram and used in the re- search to be described) were confirmed in a concurrent study of Paranjpe, Cohen, Bever and Floe." The eutectoid decomposition involves the transformation of the ? face-centered cubic interstitial solid solution of nitrogen in iron to the a body-centered cubic interstitial solid solution of nitrogen in iron and the ?' nitride of iron. This nitride is essentially the compound Fe,N; it also possesses a face-centered cubic lattice but a considerably larger one than the ?; the nitrogen atoms in ?' are arranged in an ordered way in the centers of the unit cubes.8,10,11 A martensitic structure has also been reported8,12 in iron-nitrogen alloys and was studied in the research to be described here. Materials and Methods The specimens used in this investigation were prepared by nitriding "pure" iron. This iron was supplied by the Westinghouse Research Laboratories and is the product bearing their trade name "Puron"; it contains about 0.04 wt pct total impurities, the major portion of which is oxygen. Specimens were ribbons several inches long, a tenth of an inch wide, and 0.125 mm thick; this was the

Jan 1, 1951

By Arthur F. Taggart, T. C. Fitt, A. W. Thomas

IT was noticed early by operators that high recoveries and flocculation of the sulphide minerals were closely correlated in agitation-froth flotation. Later, this readily visible flocculation was found almost invariably to be due to the binding together of the oiled sulphides by minute air bubbles, and is now known to be characteristic of pulps in which at least one of the mineral species is coated with an insoluble collecting oil. In 1930 it was reported1 that in differential flotation a correlation exists between Brownian movement of particles in the pulp and their nonfloatability, and that Brownian movement and dispersion are likewise correlated, whence it would appear to follow that dispersion of a mineral particle in a flotation pulp denotes a particle condition unfavorable to flotation. In 1934 it was postulated2 that Brownian movement, dispersion and nonfloatability all flow from the condition of the surface of the dispersed particles. It was also postulated at that time that the surfaces of dispersed particles are ionized, the ionized compound being a product of reaction between a component of the particle and a. component of the pulp, of a mass solubility of the general order of a fraction of a milligram to 15 to 20 mg. per liter. It was then further asserted, and has since been confirmed by Bankoff,3 that sulphides so conditioned with soluble collectors as to be floatable flocculate without the intervention of air bubbles as binding media. The present paper comprises an inquiry into the nature of the bound and counter ions in zinc sulphide dispersed by sodium arsenate. A part of its findings was mentioned in the 1934 paper above cited.2 The tests show that: I. When powdered granular zinc sulphide is immersed in aqueous solutions of sodium arsenate, arsenate ion is abstracted from solution and anchored to the solid surface, while sulphate and lower sulphoxy ions are concurrently displaced therefrom in substantially stoichiometric quantities. 2. The ion counterbalancing the anchored arsenate ion is zinc. 3. Dispersion and Brownian movement of zinc sulphide are concurrently maxima at an arsenate-ion concentration lying between 0.01 and 0.001-molar sodium arsenate. 4. Any condition or reaction that tends to remove the zinc arsenate coating from the zinc sulphide particles decreases dispersion and Brownian movement concurrently. EXPERIMENTAL Three samples of zinc sulphide were used. Lot I was C.P. zinc sulphide, washed well beyond absence of chloride, as shown by test with silver ion. Lot 2 was prepared by precipita-

Jan 1, 1943

By G. R. Leverant

RECENT investigations1,2 of the low-cycle fatigue behavior of pure copper under strain cycling conditions have shown that a unique saturation stress level is eventually attained for each value of applied plastic strain amplitude. The dislocation substructure of copper at the saturation stress level is in the form of cells whose diameter decreases with increasing saturation stress level, i.e., plastic strain amplitude. In addition, both the saturation stress level and the cellular substructure are completely reversible. That is, the saturation stress level and accompanying cell size are determined solely by the present conditions of testing and are, therefore, independent of any previous cyclic history. The mechanical and substructural reversibility observed in pure copper, which has a relatively high stacking fault energy, is not observedz for Cu-7.5A1 which has a much lower stacking fault energy. This implies that easy cross slip (wavy slip) is a prerequisite for reversible fatigue behavior. A dispersion of fine, nondeformable particles of a second phase in a metal matrix tends to stabilize substruc- tures introduced by forming operations during subsequent elevated-temperature heat treatments.3 This raises the question as to whether a finely dispersed second phase can induce an element of irre-versibility into the cyclic deformation behavior of a wavy slip material at room temperature, due to partial stabilization of the initially introduced substructure. Since nickel has a higher stacking fault energy than copper,6 pure nickel should be characterized by cyclic reversibility. Therefore, TD-nickel* (Ni-2ThO.r) was

Jan 1, 1968

By Paul A. Farrar, Harold Margolin

The Ti-Al-V system has been delineated from 50 to 100 wt pct Ti and front 600 to 1400°C by X-ray and ntetallographic techniques. Isothermal sections were delineated at 600, 700, 800, 900, 1000, 1100, 1200, 1300, and 1400°C. X-ray and metallographic evidence indicated the presence of two phases and in addition to those reported by previous investigators of the ternary system'-3. T HE titanium-rich region of the Ti-Al-V system as originally proposed by Rausch et UZ, and Jordan and Duwez3 was based on the binary Ti-Al diagram as proposed by Bumps et uZ. As additional phases have been shown to exist5-' in the region previously thought to be all a, the titanium-rich region of the Ti-Al-V system is open to serious question. Therefore, in order to determine the effect of the indicated changes in the Binary Ti-Al system on the ternary Ti-Al-V system the present investigation was initiated. EXPERIMENTAL PROCEDURE The experimental procedures in this investigation are the standard techniques used in the study of titanium-alloy systems which have been described in detail previously.1° Consequently, only details pertinent to the present work are discussed. The alloys employed for the delineation of this system were prepared from titanium obtained from the Bureau of Mines (73 BHN) 99.99 pct Al and 99.7 pct V, by the consumable arc-melting technique. The titanium was premelted into buttons of 25 g because spattering during the first melt caused uncontrollable loss of alloying constituents. Typical analyses of the material used have been reported elsewhere Attempts to hot roll the alloys prior to heat treatment were made on the first series of alloys prepared, but as the area of extensive hot workability was fairly restricted, see Table I, this practice was discontinued. The times of isothermal annealing are given in Table 11. A preliminary heat treatment of 96 hr at 1000°C was used prior to heat treatment at lower temperatures. The standard techniques used for polishing specimens involved belt-grinding, grinding on emery paper, polishing electrolytically, and etching with Remington "A" etch. In the low-alloy region it was found that the oRo etch, developed by Ence and Margolin,o gave better contrast between phases. Where this procedure did not differentiate between phases clearly, the method of stain etching developed by Ence and was used. It has been previously reported15 that filing of titanium alloys is not desirable for producing X-ray powders, since the powder becomes contaminated by the file material. Therefore, for those samples not brittle enough to Crush, the procedure described below was used. The specimen was wrapped in molybdenum sheet and placed in a vacuum system and evacuated to 0.03 p. Palladium-pur if ied hydrogen was then admitted to the system until a partial pressure of 5o Cm of H was reached. The specimen was heated in the system to the temperature of original heat treatment and was slowly cooled over a period of 3 hr to 400°C while the partial pressure of hydrogen was maintained. The sample was removed from the system after it had completely cooled and was crushed to a powder of 230 to 270 mesh. The powder, wrapped in molybdenum sheet, was dehydrogenated at the temperature of original heat treatment until a partial pressure of 0.03 p was maintained in the system for at least 1/2 hr. The tube containing the powders was quenched in iced brine while still connected to the vacuum system. After dehydrogenation, the powder, except for the

Jan 1, 1962

By O. Chanute

all of' level atid grade curve excepting Nos. 897, 898, 899, and 900, because of the impossibility of grouping them in the same nlonner, no two Iraving the chemical composition and physical prnprtiw as tho only v:iriubles. Phosphorus ~tnits have been taken to show the relatia h:wdnes. Of these 16 groups, 10 decidedly indicate slower wear firr tile harder rail. Of the remaining 6 groups, three (groups 2, 9, and 15) come well within the limits of error (.25 pound per yard) inherent in the palculation of the data as pointed out by Dr. Dndley; they catrnot, therefore, be considered tls exceptions. Group 2 and 15 arc but little outside of the limita of error. Rail 923 of group 9 is obviously abnornlal. This is probahly due to its being overheated, which the chemical analysis shows might easily be the case, and which the physical tc~ts and its low specific gravity tend to c-nfirm. We inry say, then, thnt 13 of these 16 groups fairly indicate, if they do not definitely point out, th:kt, under the same condition% tbe harder rail gives the slower wear. Of course, these comparisons are too few to enable us to arrive at positive ~?o-nclusions; but indications thus obtained are, I believe, fir more vsluitblc and tresttvc~rthy than those fhzt averages rvottld give us, mnde up from any ~lumhr of rails under intloy difi~rcal, conditions. Finally, it, seems to me, that the conclusions arrived at earlier in my remarks, together with, and confirmed by the last, show strong evidence that, under the same conditions, the harder rail will givc the slower wear. 0. C~~anute, New York CITY: We are very much shlipl, 1 ant sure, to Mr. Sandberg for his paper upn " Rail Ryaifications and Rail Inspertion in Europe." We have in thp United States bithhrto Been inspecting mils sonlewl~at haphazard, and we ore glad to gtbt tfie results of Mr. Sandberg's long experience. We recognize that he was an)ong the first, if not the very firwt, to iipply mare rittional and scientific rules to the designing of irou rails., niora recently, to adapt tlitve rules to the clesigtting of steel I':I~]R, to conform to the oapaljilities and rqniretnento of this new n1:ttcrial. Although we have generally adopted, in this country, sectinns for hteel rails which marly of our railway men think even bottar than those of Mr. Snlldlmrg, he is neverthelees the Ieat3er in foot.iito11~ we have followed ever since it has been est~blished

Jan 1, 1881

Upper Peninsula W. O. HOTCHKISS, Chairman C. H. BAXTER, Secretary-Treasurer, Michigan College of Mining and Technology, Houghton, Mich. S. R. ELLIOTT RUDOLPH ERICSON W. H. SCHACHT Utah Meets second Thursday of each month, October to May, inclusive B. L. SACKETT, Chairman C. T. VAN WINKLE, Vice-chairman G. L. OLDRIGHT, Secretary-Treasurer, U. S. Bureau of Mines, Salt Lake City, Utah A. E. RING L. A. WALKER

Jan 1, 1932

By C. J. Bauer

WHEN the pipe lines from the Middle East to the Mediterranean are completed, the Middle East supplies will relieve the strain on Western Hemisphere petroleum resources, part of which are now shipped for Eastern Hemisphere use. A sketch of the world petroleum situation as it appears today and in the immediate future will help in understanding the future place of Middle East oil supplies. Anticipated 1951 world demand is slightly under four billion barrels. To meet this requirement, crude output and refinery runs throughout the world (including Russia) must be increased about two million barrels per day above the average of 1947. This increment, together with pipe lines, tankers, and other facilities, will require in excess of ten billion dollars of new capital in the next four years. We are, therefore, looking forward to the greatest expansion program in the history of the industry.

Jan 1, 1948

By Frank T. Sisco, Selma F. Hermann

gancse constituent in the alpha grains. Nickel produces a structure of alpha plus cutectoid almost identical with that of the normal aluminum bronze (Fig. 38), except for the rod-shaped nickel constituent in the alpha grains. Silicon produccs a light structure with small regular needles, possibly a modified form of beta. Fig. 45 shows the alpha plus beta structure of the normal 10 per cent. aluminum alloy as quenched. Manganese produces large grains of beta with alpha as a tiny constituent scattered throughout the spceimen. Silicon, on the other hand, produces all alpha, with free silicon present. One per cent. iron produces alpha plus beta, with a tiny constituent present in the alpha grains. Five per cent. iron introduces twins in the alpha and a nodular iron constituent in both the alpha and the beta. Figs. 50-58 include the structures of the alloys with 8 per cent, aluminum, tempered at 400" C. and at 650" C. Fig. 50 is the normal structure as drawn at 400" C!. It consists of large grains of twinned alpha plus a very small amount of beta. One per cent. silicon increases the amount of beta enormously, but when tempered at 650' C, the beta degenerates to a hard blue network constituent. One per cent. cobalt results in a structure of exceedingly fine-grained, twinned alpha, heavily mottled. Nickel produces large soft grains of alpha with a dot constituent in some of the grains, when tempered at 650" C. Manganese, when tempered at 400" C. produces alpha grains and shows the decom-

Jan 1, 1931

By H. Reiss

The zone-melting process in which redistribution of solute in a solid bar is effected by the passage of a molten zone is considered mathematically. Simple approximate techniques are developed for computing the manner in which redistribution occurs as molten zones continue to pass. The introduction of the "zone-melting flux" provides valuable insight into the nature of the phenomenon, as well as a central mathematical theme in terms of which the process can be discussed. Curves are presented for typical and general cases. AN extremely efficient purification technique was described recently by Pfann.1 Known as zone refining, it consisted of the slow passage of a series of molten zones, produced by external heaters, through a long solid ingot of the substance to be purified. Equations were given for the maximum separation attainable, and a numerical computation method was described for obtaining the concentration in the ingot after a given number of zone passes. The present paper offers an interpretation of the physical nature of zone melting in terms of a transport process in which formal diffusive and convec-tive flows occur. This interpretation, in addition to providing insight into the physical nature of the process, also provides a basis for its mathematical treatment. From this basis, useful equations are developed for the solute concentration in the ingot as a function of the number of zone passes. These are applicable particularly where large numbers of passes are necessary and where numerical computational methods might be laborious. All considerations will deal with the limiting form of the process, described by Pfann,' in which: 1—Diffusion in the solid is considered negligible. 2—Mixing in the liquid is supposed, complete. 3—The distribution coefficient, k, measuring the ratio (at equilibrium) of solute concentration in the solid to that in the liquid is supposed, independent of composition. In general, this paper will be concerned with a bar of uniform (actually unit) cross section, ex- tending in the x-direction from x = 0 to x = L, where L may be infinite. Zone melting is a transport process, and as such must admit of interpretation in terms of a flux of transported quantity. However, the progress of operation is not measured in units of time but in terms of the number of completed zone passes. Consequently, the zone-melting flux will be a rate, per unit pass, rather than per unit time. The description of this flux and the examination of its properties is given below. Zone-Melting Flux Fig. 1 represents an intermediate stage of the nth pass. Concentration C is plotted against distance, x. The molten zone with its back at the point x and front at x + I moves in the direction indicated by the arrow. As it moves, it leaves behind the nth

Jan 1, 1955

By C. J. Bier, J. F. O?Keefe

THIS study was carried out with copper because it represents the simplest form of sintering, in that but one metal is involved and all reactions occur in the solid state. [ ] The present work will cover three variables affecting the sintering process; namely, briquetting pressure, sintering temperature and time in hot zone. Although strength and dimensional changes were observed, this is primarily a metallographic study of the sintering process in copper. The term "sintering" should be understood to mean the process by which the metal powder particles of the compact become united into one body. MATERIAL USED The copper powder used was made from reduced copper oxide, and is typical of a grade used for the mass production of parts formed of metal powders. The screen analysis of the powder was as follows: [ ] The minus 325-mesh analysis was made by using a Roller Air Analyzer.1,2 The apparent density is here defined as the weight per cubic centimeter of the [ ] loose, unpacked powder as measured with the Hall flowmeter. The value for the powder used was 2.57 grams per cubic centimeter.

Jan 1, 1944

By Oscar E. Harder

THE TERM "physical metallurgy' is used in the title of this lecture in preference to "metallography ?because the former has a broader meaning with most audiences, some people thinking of the latter as being limited to work with the microscope. This distinction, how- ever, has not been held by the out- standing workers in the field of metallography, such as the late Professor Sauveur. In the broadest sense metallography is essentially the same as physical metallurgy. The American Society for Testing Materials has adopted-the following definition: "Metallography is that branch of science which relates to the constitution and structure, and their relation to the properties of metals and alloys." This definition might be improved by adding after "properties" -"and their industrial and scientific uses." Metallography has also been defined as the science of metals and alloys. Physical metallurgy is to be distinguished from process metallurgy in that the latter relates particularly to the production of metals from the ores.

Jan 1, 1940

By Garth M. Crosby, F. McIntosh Galbraith, Bronson Stringham

THE Hercules mine is located in the northeastern section of the Coeur d'Alene district, approximately 1 1/2 miles north of the town of Burke, Idaho. Surface indications of the ore deposit were first discovered in 1886, but regular mine production was not started until 1902 and was continuous until April 1925, when the known ore had been extracted. Incomplete records show that from 1912 until operations were suspended the mine produced 2 1/2 million tons of ore containing 9.4 pct lead and 7.7 oz of silver per ton, together with an estimated 2 pct zinc, 0.3 pct copper, and 20 pct iron. This operation was the first in. a series of mining enterprises culminating in October 1947 with the consolidation of Day Mines, Inc. In the same year it was decided to unwater the levels below the collar of the Hercules shaft in the hope of finding some indication of a recurrence of ore. The unwatering operation has been described in a. previous paper.' The initial exploration, following recapture of the workings, showed sufficient promise to warrant a detailed study of the mineralogy with modern techniques. The general geo1ogy of the Coeur d'Alene district, including a detailed description of the rock types encountered, has been comprehensively treated by Ransome and Calkins' in their classic paper, and only local background description, therefore, is felt to be appropriate here. The Hercules deposit transects a portion of the trough of a broad south-trending synclinorium which has been greatly complicated by faulting. More locally, it lies within a block of ground bounded on the east; by the O'Neil Gulch fault, a steep north-south overthrust of considerable magnitude, and on the west by a monzonite stock, the outcrop of which is 1/2 mile or more wide and 5 miles long. The country rock is composed of thin to medium-bedded argillites and argillaceous quartz-ites of the Prichard and Burke formations, the oldest members of the Pre-cambrian Belt Series of sediments in the area, believed to be of Algonkian age. The contact between them is a conformable gradation. The argillite is colored gray to tannish-gray and is fine-grained, compact, and generally massive in structure. Under the microscope the unaltered argillite is seen to be composed principally of anhedral quartz and a few feldspar grains which were at one time presumably partly rounded sand grains, but as a result of recrystallization and cementation by silica, the interstices are now almost obliterated and quartz grains show crenulate boundaries. The sizes of these crystals vary from 0.5 mm down to 0.1 mm in greatest dimension. In all specimens sericite comprises 10 to 20 pct of the rock and is present abundantly between most of the grains as flakes or shreds which vary considerably in size. Sometimes they form a fine felt-like mat or aggregate, and sometimes flakes are seen which appear to be good muscovite. In some specimens, separated rhombic-shaped carbonate grains are abundant, and in some instances these have been changed to sericite. Mining operations to date have explored the Hercules vein to a maximum vertical depth of 3600 ft below its outcrop, and along a maximum strike-length of 3600 ft on certain of the lower mine levels. The main orebody is irregular in outline, extending over a variable strike-length of 400 to 1500 ft; and it is intersected by a strong transverse fault that has been traced from the surface to the bottom level. This has been named the Hercules fault, and apart from the vein itself, it is the most prominent structural feature in the mine. There is good evidence that it existed prior to the introduction of ore solutions and may have influenced ore deposition, but it was also the locus of important post-ore displacement and shows a progressive right-handed horizontal component reaching 200 ft on the deeper levels. Its vertical component is not definitely known but may be considerably greater. The fault strikes 20° N to 50° E and dips westerly at angles of 70" to 45", flattening in dip where it crosses the original orebody from east to west between 1000 and 1600 ft below the surface. At about 3000 ft in depth the Hercules fault is joined by a vertical fault of similar strike, and the major post-ore dis-placement below their junction is taken up along this vertical branch of the structure, now called the Mercury fault. Recent work has been concentrated in this vicinity. Another structural feature of special geologic interest, though of little economic importance, is the occurrence of a porphyritic dike in this area. This lies a short distance above the Hercules fault, essentially parallel to it, and is 5 to 15 ft in thickness. It appears at first glance to cut the mineralization, suggesting push-apart relationship, but small stringers of the vein minerals have been observed to penetrate the dike for a matter of inches at several points. The dike is thought to be related to the monzonite intrusion. A vertical longitudinal projection of the mine is shown in Fig. 1, which illustrates most of the features discussed above. The Hercules vein was deposited along the course of a strong, persistent shear zone that now appears as a braided network of gouge seams running through more or less crushed and shattered country rock. It strikes 70° N to 80° W and dips southerly at an average of 75". Barren parts of the structure vary in width from less than 1 ft to more than 15 ft. The width of mineralized segments may be double that. Although the evidence is not conclusive, pre-mineral, normal movement along the zone may be 1000 or 1500 ft. The horizontal component is unknown. Post-ore movement appears to have been

Jan 1, 1954

By G. M. Ritcey, A. W. Ashbrook, E. G. Joe

Solvent-in-pulp extraction of uranium from acid leach slurries of flotation concentrates is described. Solvent extraction was carried out in a 10 in. diam pulsed-plate column. The extractant was a 0.1 M tertiary amine (General Mills Alamine 336) in a kerosene diluent containing isodecanol as an emulsion suppressor and third phase inhibitor. In pilot plant operation at the Beaverlodge mill of Eldorado Mining and Refining, Ltd., slurry feeds containing up to 35% solids were processed at a throughput rate of 13.5 tpd of dry feed. Uranium extraction obtained was as high as 98%. Amine losses to the raffinate were approximately 0.07 lb amine per ton of original dry feed. The Beaverlodge Mill of Eldorado Mining and Refining employs a carbonate leach for the extraction of uranium from the ore.',' Prior to carbonate leaching sulphides are removed by flotation to reduce reagent consumption. This flotation concentrate containing some uranium is then leached with sulfuric acid, filtered, and the uranium precipitated with magnesium hydroxide. The precipitate is then returned to the carbonate leach circuit. Although the tonnage of flotation concentrate treated by acid leaching is low, reagent costs are relatively high. Also maintenance costs on the acid leach filtration circuit were beginning to show significant increases. The choice of solvent extraction-in-pulp as an alternative to the present circuit was influenced by the following factors: 1) elimination of acid pulp filtration, 2) increase in overall recovery because of soluble loss elimination, 3) reduction of reagent cost (mill sodium carbonate solutions are used as strip), and 4) production of higher purity precipitate at the mill site. Because a solvent-in-pulp process would be difficult to test on a bench-scale, the Eldorado experience in the use of pulse columns,3-5 mixer-settlers,6 and solvent-in-pulp operations in particular7 was applied directly to the initial pilot plant carried out during the summer of 1965 and followed by the second pilot plant in 1966. The latter work, which is presented in this paper, determined the following factors for anticipated scale-up to plant production: 1) overall uranium recovery by this process, 2) tonnage throughput expected, and 3) solvent losses anticipated for the full-scale plant. The equipment used consisted of a 10 in. diam extraction pulse column and three mixer-settlers for scrubbing, stripping, and acid equilibration. All equipment was designed by Eldorado and much of the pilot plant was built at the mill site. PROCESS CHEMISTRY Feed to the acid leach plant consists of a sulphide flotation1,2 concentrate containing mainly pyrite, uranium and graphite, with a particle size of 90%

Jan 1, 1968

By Robert H. Merrill

In 1960, the Kennecott Copper Corp. and the U.S. Bureau of Mines entered into a joint research program to determine the changes in stress, strain, and displacement created by changes in slope angles. The field site was the Kimbley Pit, located near Ely, Nev. The supporting laboratory investigations were made at the Bureau's Denver Mining Research Center. Following a study to determine the rock stresses in the mining district, the strike and dip of geologic defects (fractures) in the rock, and the laboratory-determined strength of the rock, a new slope angle and pit configuration was selected, and instruments were installed to measure changes in stress, strain, displacement, microseismic noise rate, and sonic velocities at several points in the west wall of the pit. Between February and November 1966, the west slope was changed from an average angle of 45' to a slope angle that started at 45° on the south wall, and gradually increased to 575' at the center of the west wall, and to 61° on the north wall. The pit was deepened from about 500 ft to about 550 ft. About 2.55 million tons of waste and ore were removed by stripping and mining. Measurements made between November 1965 and September 1967 showed that the pit wall was stable before excavation began, that changes in the measured quantities occurred in the pit wall during the excavation, and that the wall returned to a condition of equilibrium after the mining was completed. The need for a method and the technology to pre-design a pit slope does not require elaboration. About 5 billion tons of material are excavated yearly by surface mining methods in the United States, and the economics, safety, and availability of lower grade metals, nonmetals and fuels could all be substantially improved if operators could preselect optimum slope angles. Mining companies and the Bureau of Mines have recognized the need for developing engineering methods to determine stable slope angles. In the industry, Kennecott Copper Corp. had been making an

Jan 1, 1969