Search Documents

By N. Christensen, B. Augland, T. H. Johansen

Samples of an Fe-Nb alloy were brought to equilibriurtr with hydrogen-methane mixtures in the temperature range from 950° to 1050°C, and subsequently analyzed on their carbon contents. The solubility pvoduct L = [%Nb] [%C] may be represented by the equation Approximate solubilities indirectly assessed through hardness measurements have been included from a previous report. These data are shown to be in a fair agreement with the present solubility measurements. IN an investigation based on hardness measurements by de Kazinczy, Ms, and pachleitnerl the molal heat of solution of NbC was estimated to 11.5 kcal per mole. This value was considered rather small, and an investigation using a similar technique was carried out. The results indicated a heat of solution about 35 kcal per mole.2 At this stage it was decided to determine the solubility under conditions of true equilibrium . During the course of this work a similar investigation was published by Smith. 3 His heat of solution, 41.6 kcal per mole, is not very different from the value resulting from the present work (42.5 kcal per mole). Our solubility product, on the other hand, is at considerable variance with that reported by Smith. Possible reasons for these differences are discussed below. Mori, Tokizane, and saheki 7 have studied the behavior of niobium in commercial steels, with special attention to the formation of niobium carbide, nitride, and sulfide. Assuming a carbide composition Nbco.87 based on X-ray diffraction and chemical analysis of residues extracted from Fe-Nb-C-S alloys, the molal heat of solution of niobium carbide was estimated to 35.2 kcal per mole. MATERIALS AND EQUIPMENT The chemical analysis of the materials is given in Table I. Electrolytic iron* was used in the preparation of

Jan 1, 1968

By Glenn C. Waterman

Richard Strong (Oliver Iron Mining Div., U. S. Steel Corp.)—Mr. Waterman states (p. 59, Trans., January 1954): "Core-sludge combining factors have been calculaied for any combination of core-sludge recovery on the basis of several logical assumptions: 1—The sludge sample loses reliability geometrically as sludge recovery drops. 2—The sludge sample should not be used if the percentage of sludge return is less than the percentage of core recovered. 3—A core sample should receive a weighting at least equal to the percentage of core recovery." Assumptions 1 and 2 seem justified at Chuquicamata and most geologists would agree to the validity of assumption 3. However, contrary to the statement quoted above, the core sample does not in general receive a weighting at least equal to the percentage of core recovery when the Chuquicamata methgd is used. Furthermore, the basic Chuquicamata method is identical to the Longyear or relative volume core-sludge assay combining method. Finally, the Chuquicamata method does not, in its present form, reflect true geometric loss in sludge sample reliability according to the relationship L = AR (N-1) The basic equations representing the two steps of the Chuquicamata method can be combined algebraically as follows (using the symbology of the original article except as noted): Vol A + B Assay 2 = ASA = Assay 1 Vol A VolB Core Assay [I] Vol A CA.F + ASA (100 —F) Combined grade =[21 100 Pct where F and (100 — F) are the core and adjusted sludge assay factors from Fig. 3. Substituting Eqs. 1 and 2 and collecting terms Combined grade = Vol B Vol A + B CAF (100—-F) + Assay 1 (100-F) Vol A Vol A 100 pct Eq. 3 is a unified and general statement of the Chuquicamata method. The true core factor includes not only the factor F from Fig. 3 but also the quantity VolB ------------- (100 — F), which is implicit in the value of Vol A the adjusted sludge assay. This quantity is real and positive for all values of F and core recovery less than 100. Therefore the true core factor is always less than F except when F is equal to 100. If sludge recovery is 100 pct, Eq. 3 can be further simplified as follows: Let F = percentage of core recovered. Let Vol A = Vdh (100 Pct — Pct CR) where Vdh is the total volume of the sampled interval and let Vol B = (Vdh — Vc.) Pct CR where V, is the core volume in the sampled interval at 100 pct core recovery. Then combined grade = Vo V. CA Pct CR- + Assay 1, 100 Pct — Pct CR Vdh Vdh [4] 100 Pct Eq. 4 shows that when sludge recovery is 100 pct the laboratory sludge assay receives significant weight in the Chuquicamata method, even at 100 pct core recovery. The maximum weight assigned to the laboratory sludge assay depends on drillhole size, as follows: Eq. 4, with suitable changes in symbology, is identical to Royce's formula 8,' which is a statement of the Longyear or relative volume method of combining core and sludge assays. If Mr. Waterman's assumption 3 is of paramount concern to the geologist, the Royce method (for core recoveries of 60 pct and above) or a method employing the percentage of core recovered as a core weighting factor are the only recognized methods known to the writer which achieve the desired result. A modification of the latter method embodying Mr. Waterman's assumptions 1 and 2 would result from applying the factors from Fig. 3 directly to the laboratory core and sludge assays.

Jan 1, 1956

By F. J. Williams

BARITE, naturally occurring barium sulphate, is the chief barium mineral that is produced commercially. Barite is also called "barytes," "heavy spar," sometimes "baryta" and, locally in Missouri, "tiff." Pure barite is white, opaque to transparent. It crystallizes in the orthorhombic system, frequently with twinning. Impurities cause a wide variation in color, commonly buff, gray and white with irregular reddish iron stains. Less frequently found are shades of yellow, green, blue, brown, and black. The rock is brittle and breaks with an uneven fracture, although specimens from some of the residual deposits, particularly in Missouri, appear to have a cleavage due to the separation of the different layers of deposition. The hardness varies from 2.5 to 3.5 on Mohs' scale and different localities are said to produce either "hard" or "soft" barite. This generally refers to the ease of grinding of the product. The specific gravity of pure barite is 4.5 and this will vary downward, depending on the impurities present. The mineral has a white streak and a pearly to vitreous or sometimes stony luster. Pure barite contains 65.7 pct BaO and 34.3 pct SO3. Witherite, native barium carbonate, is not mined in the United States at the present time although a number of occurrences have been reported. A small quantity of witherite has been removed from a mine at El Portal, California, but the area high in witherite was small and soon depleted. The bulk of the deposit is predominantly barite. Great Britain is the world source of witherite and small quantities are imported into the United States. DISTRIBUTION OF DEPOSITS Occurrence of barite is widespread; it has been reported on all the continents and in all the major countries of the world. Deposits vary from those containing millions of tons down to scattered rock fragments

Jan 1, 1949

By Nicholas J. Grant, John Chipman

A full understanding of the behavior of sulphur in the basic open-hearth process has been delayed by lack of dependable data covering a wide range of slag conditions in the absence of other complicating factors that are likely to be present under operating conditions. It has been generally accepted that strongly basic slags will dissolve more sulphur than will those in which the acidic and basic constituents are more nearly balanced. It has been known that both slag and metal would absorb sulphur from the flame when the sulphur content of the fuel is high. It has been generally believed that manganese assists in the transfer of sulphur from metal to slag. Almost nothing has been known of the effect of temperature upon desulphurization;the data have been conflicting and there has been a tendency to depend rather heavily upon analogy with the better understood desulphurizing reaction of the blast furnace. Many attempts have been made to build up from open-hearth data a satisfactory theory of the chemical reactions involved in the process. That this has been an extremely difficult task is owing to two reasons that have been very generally recognized. The first is the parallel and simultaneous reaction of sulphur transfer between flame and bath. The second is the difficulty of distinguishing between the factors that ultimately limit the transfer from metal to slag—i.e., equilibrium conditions—and those whose influence is only upon the rate of transfer. It has been the object of the work here recounted to study the equilibrium distribution of sulphur between slag and metal in the absence of these complicating factors, with the hope that a better understanding of the equilibria involved would lead to a better control of the over-all process in the open-hearth furnace. A review of the literature on steelmaking reveals almost complete agreement with respect to the paramount importance of lime in promoting desulphurization. In expressing this effect in quantitative terms, however, and in formulating the relationships between the concentrations of other slag components and the desulphurizing power, there is little agreement. For instance, the "basicity" or basic strength of the slag is commonly measured by some kind of ratio of concentration of basic to acidic oxides. Of these, the following have been reviewed by Schenck:20 V radio = % CaO/%SiO, Körber and Oelsen's _ % CaO'. 100/% CaO + % SiO2 where (%CaO') = % CaO- 1.18% P2O5. Herty's B ratio = % CaO - (0.93 . % SO2) - (1.18% P205) Among others there appear the following: 20 References are at the end of the paper.

Jan 1, 1947

By Nicholas J. Grant, John Chipman

A full understanding of the behavior of sulphur in the basic open-hearth process has been delayed by lack of dependable data covering a wide range of slag conditions in the absence of other complicating factors that are likely to be present under operating conditions. It has been generally accepted that strongly basic slags will dissolve more sulphur than will those in which the acidic and basic constituents are more nearly balanced. It has been known that both slag and metal would absorb sulphur from the flame when the sulphur content of the fuel is high. It has been generally believed that manganese assists in the transfer of sulphur from metal to slag. Almost nothing has been known of the effect of temperature upon desulphurization;the data have been conflicting and there has been a tendency to depend rather heavily upon analogy with the better understood desulphurizing reaction of the blast furnace. Many attempts have been made to build up from open-hearth data a satisfactory theory of the chemical reactions involved in the process. That this has been an extremely difficult task is owing to two reasons that have been very generally recognized. The first is the parallel and simultaneous reaction of sulphur transfer between flame and bath. The second is the difficulty of distinguishing between the factors that ultimately limit the transfer from metal to slag—i.e., equilibrium conditions—and those whose influence is only upon the rate of transfer. It has been the object of the work here recounted to study the equilibrium distribution of sulphur between slag and metal in the absence of these complicating factors, with the hope that a better understanding of the equilibria involved would lead to a better control of the over-all process in the open-hearth furnace. A review of the literature on steelmaking reveals almost complete agreement with respect to the paramount importance of lime in promoting desulphurization. In expressing this effect in quantitative terms, however, and in formulating the relationships between the concentrations of other slag components and the desulphurizing power, there is little agreement. For instance, the "basicity" or basic strength of the slag is commonly measured by some kind of ratio of concentration of basic to acidic oxides. Of these, the following have been reviewed by Schenck:20 V radio = % CaO/%SiO, Körber and Oelsen's _ % CaO'. 100/% CaO + % SiO2 where (%CaO') = % CaO- 1.18% P2O5. Herty's B ratio = % CaO - (0.93 . % SO2) - (1.18% P205) Among others there appear the following: 20 References are at the end of the paper.

Jan 1, 1947

By O. D. Gaither

This paper is an analytical study of the flow of fluids through small vertical conduits. Small conduits are defined as 11/4-in. nominal diameter tubing size and smaller, and approximately twice this area for annular conduits (i.e., 1- X 21/2-in. annulus and smaller). Experimental data are presented for the 1-X2-in. and 11/4- X 2%-in. annuli, and the I-in. and 11/4-in. tubing, since these represent the small conduit sizes and configurations generally encountered in oilfield applications. Data have been gathered for these conduits for single-phase water, single-phase gas and two-phase water-gas mixtures, with particular emphasis on high gas-liquid ratios. Water rates in excess of 2,000 BID and gas rates in excess of 2.5 MMcf/D, and two-phase flow ratios in between these two, represent the scope of the data gathered. Existing equations have been applied to predict flowing pressures and compared with experimental data. New correlations have been developed. INTRODUCTION The increased economic pressure on the domestic oil industry in the United States has constantly required the use of new techniques and equipment designed to reduce the cost of finding and producing oil and gas. Since tangible items are most readily apparent in economic analysis, the advent of lower-cost well completions was inevitable. One of the methods used to reduce costs which has received widespread attention is the slim-hole completion technique where tubing is used as the well casing and in which small conduits are used for tubing if necessary. Small conduits, defined by Kirkpatrick1 as "11/4-in. diameter nominal tubing and smaller for tubing flow and less than twice the 11/4-in. diameter nominal tubing internal flow area for annulus flow", have also found widespread usage as siphon strings for de-watering gas wells and as "kill" strings in deep high-pressure oil and gas wells. The growing use of small-diameter tubing has resulted in an increased need for development of improved methods to measure or predict flowing bottom-hole pressures since the physical dimensions generally preclude the use of subsurface-recording pressure gauges. Even in the cases where small bombs are available, the relatively high velocities encountered at nominal flow rates make it necessary to use excessive weight bars or special hold-down devices. Attempts to use recognized correlations to accurately predict flowing or gas-lift performance in wells equipped with small conduits have been generally unsuccessful. Insufficient field data were available to allow the development of a correlation on this basis, and an experimental approach was applied in an attempt to obtain a workable relation. The experimental approach used to obtain the data presented in this paper was actually a compromise between a field installation and a laboratory study. A test well 1,000 ft in length was used to obtain flow data on single-phase liquid, single-phase gas and two-phase water-gas flowing mixtures. Liquid rates up to 2,200 B/D and gas rates up to 3 MMcf/D were used in the single-phase flow studies. Two-phase flow rates from 100 to 600 B/D with gas-liquid ratios from 500 to 8,000 cu ft/bbl were recorded. Experimental data were obtained for single- and two-phase flow through 1-in and 11/4-in. nominal tubing, and through the annuli between 1- and 2-in. and 11/4- and 2%-in. nominal tubing strings. Experimental results for the two-phase flow are compared to the Poettmann-Carpenter correlation2 which is widely used as a comparative standard for development of multiphase flow predictions in flowing and gas-lift wells. Correlations developed by Tek,3 Baxendell and Thomas" were also investigated. The experimental data recorded herein fell in between the two flow regimes as defined by Ros," and this correlation also failed to yield satisfactory results. The fact that existing correlations failed to confirm the experimental data led to the need for development of a new correlation. Although a two-phase flow study was the primary objective of this investigation, data were also recorded for single-phase flow of water and gas, and constants were developed relating to pipe roughness and equivalent diameters for annular flow. These single-phase studies assisted materially in the development of certain of the two-phase flow results. Considerable previous work has been published which presented relationship of surface measurements to bottom-hole condition. The works of Buthod and Whiteley,6 Jones,' Poettmannb and the Texas Railroad Commission" are classic examples of the successful use of mathematical relationships which allow acceptable predictions of subsurface pressures, when gas is the flowing fluid. Darcy and others have derived relationships which may be used with minor modifications to predict subsurface flowing conditions in injection and water-supply wells. As previously stated, the application of the single-phase flow relationships

By E. B. Thornhill

Discussion of the paper of E. B. THORNHILL, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 104, August, 1915, pp. 1653 to 1670. D. B. HUNTLEY, Oakland, Cal.-About 15 years ago it chanced to be my lot to cyanide some mill tailings, assaying about $5 per toll in gold and, a few cents in silver. It was in southern Idaho, a. desert region where costs are nearly as large as in central Nevada. We knew that we had a lot of tailings that had been amalgamated and contained about 1 lb. of quicksilver per ton. We knew that we would dissolve some of the quicksilver when we cyanided them with say 0.25 per cent. cyanide solution. We figured (optimistically) that the cyanide would dissolve all of the quicksilver, and we thought to capture all of that, 1 lb. per ton; and we figured out profits as partly gold, partly silver, and partly quicksilver from the recovery in working those tailings. Actually, however, we did this: We had a battery of three large, old-fashioned silver-mill retorts. We retorted our zinc-dust precipitate, recovering about ¼ lb. of quicksilver per ton treated. That was only a loss of 75 per cent. of what we originally had, but still it was profitable by virtue of the conditions. I mention it partly to call attention to the crude old way of doing it, and partly to call attention to how chemical methods for recovering quicksilver have developed in the last 15 years.

Jan 12, 1915

By R. W. Heins, N. Street

Recently Hiller1 reported results on the impairment of the strength of quartz glass rods through wetting, indicating that there was general agreement with the prediction of the Griffith formula in that for the liquids used the rods were weakest in water i.e. the liquid which probably had the greatest free energy of immersion. The Griffith equation predicts that the tensile stress necessary to propagate a crack of length c is where ? is the interfacial free energy, E Young's modulus. Since for a solid immersed in a liquid of surface tension ?L and contact angle 8 at the solid-liquid-gas contact, ?s - ?SL = ?L cos ? where ?s is the surface free energy of the solid. Hence comparison between ?L cos 0 and strength impairment should be possible. In a study of the usefulness of the Kuznetsov pendulum2 as a means of studying rock drillability we have determined the effects of various liquids on the pendulum hardness of Bavarian limestone. The pendulum used had diamond points (Burgess Vibro-graver), a period of 1.14 sec and a total on sample weight of 1191 g. The decline of the pendulum oscillations was recorded by a light beam on light sensitive paper carried on a kymograph. Rehbinder's expression relating hardness to amplitude attenuation as a function of time can be written In A = - (1/H) t + In Ao where A, A, = amplitude at time t and initial amplitude respectively, H = hardness parameter, and t = time. The line of best fit to the experimental points was determined using the IBM 7090 electronic computer, the computer also gave A, by extrapolation to zero time. The results for the various liquids tested are given in Table I and Fig. 1. The limestone surfaces were highly polished before testing and each reported hardness value represents the average of at least ten separate determinations of the pendulum decline curve. On each newly prepared surface the water value was again determined (also

Jan 1, 1964

By H. M. Davis, T. S. Jones

A methodfor accelerating the reduction of a metal oxide by carbon monoxide is to incorporate in the reduction system a nonreducible oxide which has a strong affinity for carbon dioxide and will remove it from the product gases. The effectiveness of this method was investigated by veduction experiments on specially prepared powder mixtures of SrO-ZnO ("active'.) and SrCO3-ZnO (reference). Measurements at 750o and 677°C showed that the rate of reduction of ZnO by CO was as much as an order of magnitude greater in the presence of SrO. Under the experimental conditions at least as much CO2 as generated by veduction was absorbed when SrO was present. Enlzancernent of the veduction rate by SvO resulted from modification of' gaseous djfitsion processes. THE specific question posed in this investigation was whether the reduction reaction CO + ZnO - Zn(g) + COa [1] could be accelerated by incorporating strontium oxide into the oxide charge undergoing reduction. Provided the strontium oxide was active enough, it could remove carbon dioxide from the product gases of ( 11 and form strontium carbonate, thus modifying Reaction [ 1] to CO + ZnO + SrO = Zn(g) + SrCO3 [ 2] This study of the comparative rates of Reactions [ I] and [2] can be considered as a particular case of a general scheme for increasing the rates of reduction of metal oxides by carbon monoxide. The limits of applicability of this scheme are indicated in the simple thermodynamic analysis presented in the appendix. This analysis primarily dictated the choice of the system, CO-ZnO-SrO, employed in this investigation. In addition, it was thought that a study of this scheme by use of the CO-ZnO-SrO reaction system would be of special interest in view of indications in the literature1-3 that the gaseous reduction of zinc oxide is prone to rate control by diffusion in the gas phase. The distinction should be pointed out between this and other efforts to increase the rates of reduction reactions through the use of addition agents. Additions of a wide range of chemicals have been tried with de- grees of apparent success varying from slightly negative to highly positive. The reasons for making additions have included the use of salts to produce effects akin to catalysis,4, 5 the alteration of the microstruc-tural details of the reduction process (including solid-state diffusion),6-8 and the conversion of an en-dothermic reaction into one that is exothermic or autogenous.9-12 The means used to attempt alteration of the enthalpy change has commonly been to incorporate lime into the charge, so that heat is generated by reaction with either of the reaction products, carbon dioxide or water. The use of lime in this way makes endeavors such as that of Edstrom and Wiberg similar to the present one. Furthermore, the basic principle behind the present work has previously been set forth.13 However, a detailed investigation of the type of reaction described in this work does not appear to have been conducted. EXPERIMENTAL PROCEDURE From both conceptual and physical standpoints, Reaction [2] is to be considered as the sum of two reactions:

Jan 1, 1968

By D. R. Irving

Prior to this time, ample supplies of high grade mineral fillers, such as clay, have been available close to consuming centers. Now depletion of these accessible deposits, coupled with other factors such as increasing demand due to population expansion and standard of living rise, has made development of upgrading techniques attractive to producers. Various investigations being carried out by the U.S. Bureau of Mines are described. Factors making the development of improved methods for upgrading clays attractive to producers include: depletion of accessible deposits of high-grade clays, rising transportation and labor costs, more exacting specifications, and increased demand resulting from an expanding population and a constantly rising standard of living. Industry recognizes the need for upgrading presently unusable materials and has cooperated with the U.S. Bureau of Mines by providing samples from submarginal deposits and by evaluating the products that USBM upgrades. Following are some examples of recent clay beneficiation work by the Bureau. FIRE CLAY BENEFICIATION At the Rolla Metallurgical Center, Rolla, Mo., the Bureau is conducting research to develop technically and economically feasible mineral-dressing methods to remove quartz, pyrite, and other impurities from submarginal fire clays. The research has been spurred by the growing shortage of high-grade bur-ley, flint, and plastic clays in the Missouri fire-clay district resulting from increased consumption and the low rate of discovery of new deposits of adequate quality. There apparently is ample tonnage of submarginal flint and plastic clays to maintain the industry for many years if such material can be upgraded to commercial quality. Samples have been submitted to USBM by several major producers of refractories, including A. P. Green Fire Brick Co.; Harbison-Walker Refractories Co.; Mexico Refractories Div., Kaiser Aluminum and Chemical Corp.; and Wellsville Fire Brick Co. Research on some samples has been completed and still is in progress on others. The Bureau has found that specimens containing quartz or pyrite in grains coarser than the accompanying clay generally can be upgraded either with a gravity table or hydraulic cyclone. The improvement in quality is notable not only in chemical analysis but in an increase in pyrometric cone equivalent (PCE) of one or more cones. As an example, consider the results attained on a sandy flint—a fine-grained mixture of kaolin and halloysite with quartz and minor quantities of iron and manganese oxides. Chemical analysis was: 35.4 pct alumina (A12O3) and 47.8 pct silica (SiO2). The sample contained 9.2 pct free silica as quartz. The PCE was 33. The sample was crushed to -10-mesh, blunged with water, and then stage-ground to -48-mesh. The ground sample was tabled to yield a clay fraction containing 37.6 pct A12O3, and 45.3 pct SiO2 of which 2.4 pct was free silica. The PCE was 34. Recovery of alumina by this process was 73.6 pct. Concentration of the same clay in the hydraulic cyclone was even more effective in respect to quartz removal. The clay fraction analyzed 38.6 pct A12O3, 45.0 pct SiO2 of which 0.5 pct was free silica as quartz, and had a PCE of 34. Recovery of alumina was 71.9 pct. The hydraulic cyclone was also effective in reducing the pyrite content of a plastic clay which likewise was a mixture of kaolin and halloysite, plus some pyrite, quartz, and carbonaceous material. It analyzed 30.6 pct Al2O3, 52.3 pct SiO2, 2.3 pct Fe2O3, and 0.76 pct S. The sample was blunged and screened through 10-mesh to remove some coarse pyrite, then ground to -65-mesh and cycloned to remove most of the remainder. The final product recovered 81.8 pct of the alumina at a grade of 32.3 pct A12O3, 50.9 pct SiO2, 1.4 pct Fe2O3, and 0.1 pct S. The PCE was 32-1/2, compared with a PCE of 31-1/2 for the crude clay. The fine beneficiated clays, of course, must be pelletized and dried or fired to meet commercial acceptance. This operation has already been solved by industry. Little progress has been made on two remaining problems. One is that of fine-grained impurities, not separable by table or cyclone. Flotation is being investigated to solve this. Although fine pyrite is readily rejected, a satisfactory quartz-clay separation has not been attained. The second problem, a stubborn one, is that of alkali. Samples containing as much as 5 pct potas-

Jan 1, 1961

By Edmund J. Korber, Donald E. Raab, Frank A. Burns

During the early 1960s, the advent of self- advancing longwall roof supports triggered serious consideration by Bethlehem management to introduce the technique of longwall mining at one of our central Pennsylvania coal mines. Although longwall mining was initially justified as a means to cope with the severe roof conditions at our Mine 32 (Watson, B., 1971), the result of the endeavor has been a consistent and reliable level of coal production, first from Mine 32 and then later from Mine 33, over a period of fifteen years. Longwall production from the Cambria Division has been the mainstay of the low volatile coal required by Bethlehem Steel for steel production. Let us review the events that led to this accomplishment, as well as where we stand today.

Jan 1, 1981

By Mark Sheppard

DURING the winter of 1937, the writer visited a West Virginia stone quarry at which the overburden is stripped hydraulically. The quarry is in a bed of limestone, about 200 ft. thick, which outcrops on a hillside above a small river; the quarry face is 175 ft. high. The top of the stone is cut in all directions by erosion channels, which are filled with a tough, red clay. Some of the larger channels are 30 ft. deep and 8 ft. wide. The thickness of the clay overburden ranges from a few inches to 10 ft., the average being estimated as less than 3 feet. The topography of the district is rugged, and the hillside above the quarry face is not suited to the use of the usual mechanical methods of moving dirt. Until hydraulicking was started 10 years ago, the over- burden was dug by hand labor, dumped to the quarry floor and transported to the dump in quarry cars. Cleaning deep channels was a slow and expensive process. When hydraulicking was started, the top of the quarry face was over 200 ft. above the level of the river. The pipe line was carried in a semi- circle around the top of the quarry about 200 ft. from the face and about 50 ft. above it. As there is no adequate supply of water above the quarry, the water must be pumped from the river. As quarrying progressed the pipe line was moved until the discharge points are now over 300 ft. above the river. Water is pumped from the river by a four-stage centrifugal pump having a 5-in. intake and a 4-in. discharge. It is direct-connected to a 200-hp., 2300-volt, 1760-r.p.m. induction motor. At 1760 r.p.m. the rated capacity of the pump is 750 gal. per minute under a head of 600 ft. The pump is installed in a house of frame construction on the river bank, about 10 ft. above normal water level, which also houses the pump for the mill-water supply. Above the pumps are hoisting bays into which the motors are raised whenever the river reaches flood stage. An 8-in. suction line, equipped with a strainer and a foot valve, takes the water from a concrete sump at the edge of the river. The pipe line from the pump consists of 1750 ft. of 8-in. spiral steel flanged pipe and 800 ft. of 4-in. spiral steel flanged pipe. The connection from the pump

Jan 1, 1938

By R. H. Dourson, B. H. Sage, W. N. Lacey

The compositions of coexisting phases in the methane-propane-n-pentane system were determined at 160° and -2 20°F. throughout the two-phase region, at pressures above 500 lb. per sq. in. The experimental results permitted the calculation of gas-liquid equilibrium constants as well as the establishment of the critical behavior of this ternary system. Although many binary paraffin hydrocarbon systems have been investigated, the experimental work relating to the phase behavior of ternary paraffin hydrocarbon mixtures at elevated pressures is relatively scarce, being limited to a study of the meth-ane-propane-PL-pentane system at 100°F.l,2 However, Guter and co-workers have studied the phase behavior of the methane-ethane-ethylene system at relatively low temperatures. Information concerning the phase behavior of ternary systems is of value in predicting the behavior of the components in multicomponent systems, since the influence of pressure, temperature, and concentration may be individually ascertained. In the light of the importance of such information, the study of this ternary system was extended to higher temperatures in order to increase the field of temperature in which the data could be applied. Since all states encountered in this investigation are above the critical temperature of methane, the details of its phase behavior are not of direct significance. The properties of propane in the heterogeneous region were taken from a correlation3 based upon recently published data. The corresponding information for n-pentane was taken from experimentally measured vapor pressures and volumetric data.4 The rnethane-propane system has been studied throughout the two-phase region at temperatures above 70°F.,5 while the phase behavior of the propane-n-pentane system has been established for temperatures above 160°F.6 The volumetric and phase behavior of the methane-72-pentane system has been studied in detai1.7,8 The experimental measurements serve to establish with adequate accuracy the phase behavior of the components and of the constituent binary systems for this ternary system. It is believed that, with the exception of the measurements for the methane-propane system, the uncertainties in the earlier data relating to the pure substances and the binary mixtures are probably less than those associated with the values reported here. Method The methods and apparatus employed in this investigation have been described.137 In principle, the method involved the withdrawal of samples of the coexisting gas and liquid phases from a vessel containing a heterogeneous mixture of methane, propane and n-pentane. Provision was made so that

Jan 1, 1943

By W. N. Lacey, R. H. Dourson, B. H. Sage

The compositions of coexisting phases in the methane-propane-n-pentane system were determined at 160° and -2 20°F. throughout the two-phase region, at pressures above 500 lb. per sq. in. The experimental results permitted the calculation of gas-liquid equilibrium constants as well as the establishment of the critical behavior of this ternary system. Although many binary paraffin hydrocarbon systems have been investigated, the experimental work relating to the phase behavior of ternary paraffin hydrocarbon mixtures at elevated pressures is relatively scarce, being limited to a study of the meth-ane-propane-PL-pentane system at 100°F.l,2 However, Guter and co-workers have studied the phase behavior of the methane-ethane-ethylene system at relatively low temperatures. Information concerning the phase behavior of ternary systems is of value in predicting the behavior of the components in multicomponent systems, since the influence of pressure, temperature, and concentration may be individually ascertained. In the light of the importance of such information, the study of this ternary system was extended to higher temperatures in order to increase the field of temperature in which the data could be applied. Since all states encountered in this investigation are above the critical temperature of methane, the details of its phase behavior are not of direct significance. The properties of propane in the heterogeneous region were taken from a correlation3 based upon recently published data. The corresponding information for n-pentane was taken from experimentally measured vapor pressures and volumetric data.4 The rnethane-propane system has been studied throughout the two-phase region at temperatures above 70°F.,5 while the phase behavior of the propane-n-pentane system has been established for temperatures above 160°F.6 The volumetric and phase behavior of the methane-72-pentane system has been studied in detai1.7,8 The experimental measurements serve to establish with adequate accuracy the phase behavior of the components and of the constituent binary systems for this ternary system. It is believed that, with the exception of the measurements for the methane-propane system, the uncertainties in the earlier data relating to the pure substances and the binary mixtures are probably less than those associated with the values reported here. Method The methods and apparatus employed in this investigation have been described.137 In principle, the method involved the withdrawal of samples of the coexisting gas and liquid phases from a vessel containing a heterogeneous mixture of methane, propane and n-pentane. Provision was made so that

Jan 1, 1943

[NORTH AMERICA UNITED STATES ALABAMA AUBURN Sturm & O'Brien, Consult. Engrs. °Sturm, Rolland G. BESSEMER Granger, W. C. BIRMINGHAM Air Reduction Sales Crockett, John M. Amer. Cast Iron Pipe Co. Carter, Sam F., Jr. Donoho, C. K. Anderson Elec. Corp. Davis, Moss V. J. B. Clow & Sons Neptune, Maurice D. Connors Steel Div. °Sandelin, Robert W. Hayes Aircraft Corp. Ricketts, W. E., Jr. Willhelm, A. Clyde, Jr. McWaine Cast Iron King, O. H. Worthington, B. W. Shook & Fletcher Sup. Co. Gearhart, Thomas A. Southern Res. Inst. Dismukes, Edward B., Wheelahan, Edmund J. Thomas Foys Miller, Ralph M. Union Carbide Metals, Co. Brandler, Edgar A. U. S. Pipe & Fdry. Co. Clay, Donald H. Unaffiliated Berg, H. A. Caldwell, H. A. Gilmer, H. U. Harris, Thomas H. Templeton, J. B.]

Jan 1, 1961

By Frederick T. Williams

THE purpose of this paper is to discuss the relative merits of the large 31/8 in. machine and the small 21/4-in. tappett machine in driving development-headings ; and although the . data here presented were obtained from cross-cut headings alone, experience has shown that the results are equally true in drifting, raising and winning. Recently we drove two parallel cross-cuts through the same formation, using a 3k-in. machine at the breast of one cross-cut., and a 2k-in. machine of the same make at the breast of the other. The results of this work afforded an ideal comparison, since in both cases the headings were advanced through rock practically of the same hardness and breaking-properties ; the amount of sludging was equal, and there was no difference in the condition of the steel or the machines, in the air-pressure or in the experience of the operating-crews. Some operators in the Cripple Creek district contend that there is ground which cannot be handled with the small machine, the holes being too small to contain enough powder to pull the ground, etc. The results obtained in working the property of the Portland Gold Mining Co., however, show that the ground worked by them does not fall in this class. During a period of two years there have been driven, with the small machine, 4 miles and 308 ft. of development-headings, through a diversity of ground, including Pike's Peak granite (a coarsely porphyritic type of granite), highly indurated, andesitic or phonolytic breccia, true massive andesite, trachytic phonolyte, tuffas, and along dikes of decomposed basalt and hard phonolyte; in every instance a satisfactory record was made. The headings here described were driven through highly indurated, andesitic breccia, having a hardness of from 5.2 to 7.2

Mar 1, 1906

By Henry Howe

§1. FOUR ASPECTS OF FLOW in the plastic deformation of steel by overstrain, such as punching, wire-drawing, tensile rupture, etc., are: (1) The inter-granular, i.e., the relative movements of the several grains, each as a whole; (2) the intra-granular, i.e., the relative movements of the masses of ferrite or cementite and pearlite within those grains; (3) the intra-pearlitic, i.e., the relative movements of the pearlitic ferrite and cementite; and (4) the crystal unit slipping, i.e., the travel of the minute units past each other, along the slipping planes, giving rise to the slip bands of Ewing and Rosenhain. It may be objected justly that (2), (3), and (4) are in a sense "intra-granular," and that (4) is in a sense "intra-pearlitic." Hence clearness may be gained at times by calling these "Movements of the 2d, 3d, and 4th orders" respectively.

Jan 4, 1914

By John Hays, Hammond

IT is both a pleasure and an honor to be a guest of the Institute and I thank you, Mr. President and fellow-members, for giving. me the opportunity of meeting you this evening. My esteemed friend, President Smith, has requested me to do a bit of "reminiscing" as to the earlier years of my career as a mining engineer, which has now covered a period of fifty years. Let me reassure you by promising that my narrative will not include all the experiences I have had over that long period. You will, I trust, pardon what might seem egotistical but I do not see how a personal narrative could well be otherwise.

Jan 1, 1928

IRON AND STEEL COMMITTEE ALBERT SAUVEUR, Chairman .A. A. STEVENSON, Vice-Chairman HERBERT M. BOYLSTON, Secretary, Abbot Bldg., Cambridge, Mass. Guilliaem Aertsen, Robert W. Hunt, .-E: Gybbon Spilsbury, John Birkinbine, J. E. Johnson, Jr., J. S. Unger, William H. Blauvelt, William Kelly, Felix A. Vogel, Charles A. Buck, Charles Kirchhoff, Leonard Waldo, James Gayley, Richard Moldenke, William R. Walker, Henry D. Hibbard, Joseph W. Richards, William R. Webster, Henry M. Howe, C. F. W. Rys, Frederick W. Wood. Manuscripts of the following papers on iron and steel for the February -meeting have been received and accepted: Albert Sauveur, Notes on Heating and Cooling Curves of Professor Carpenter's Electrolytic Iron. H. M. Howe and A. G. Levy, Notes; on the Plastic Deformation of Steel during Overstrain.

Jan 2, 1914

By J. J. Kramer, W. A. Tiller, G. F. Bolling

THE axial orientations of columnar crystals in unidirectionally solidified ingots of zone-refined zinc and tin have been examined using the techniques recently described by us.' Both metals had an initial purity of 99.999+ pct before zone refining and satisfied all qualitative guides for very high purity after zone refining. Fig. 1 presents the orientations of the columnar crystals for tin and zinc, respectively. For tin, there is a preference for grains growing in the [I101 direction, i.e., the dendrite direction.' For zinc, a weak preference for the [0001] direction is seen (a random population in the unit triangle would give equal density on either side of the 60-deg circle centered on [0001]).' There was no apparent evidence for dendritic growth in either metal. These results, and those previously reported,' confirm the recent investigation by Hellawell and Herbert of casting textures observed for zone-refined lead, zinc, and tin.4 The preferred casting orientations for these metals in both the impure and zone-refined states are given in Table I. In the experiments on zone-refined lead,' it was shown that two separate textures existed: a preferred (111) nucleation texture existed at the chill surface and a preferred (111) texture developed during solidification. Either effect is sufficient to produce the result recorded in Table I. Similarly the results recorded for tin and zinc may be attributable to either a preferred nucleation or a preferred growth phenomenon and additional experiments are required to separate these two possible explanations. Hellawell and Herbert' attribute their results to a preferred growth process and account for it on the basis of a "layer-growth" model proposed much earlier by one of the present authors.5 An equally satisfactory growth model would be that based upon anisotropic surface energies. However, both of these growth models would indicate that the preferred growth direction for very pure metals should be normal to the plane of closest packing in the metal. This is consistent for zinc but, contrary to the conclusion of Hellawell and Herbert, it is not consistent for tin since here the (100) is expected to exhibit a greater density of packing than the (110). Although tin is expected to exhibit an anisotropy of thermal conductivity, we would expect the thermal conductivity to be the same in the [1101 as the [l00]

Jan 1, 1963