Search Documents

TWO recent developments in open hearth steelmaking have had a substantial impact on metallurgical practices and operating procedures. These are: (1) the use of oxygen roof lances for accelerating the refining reactions, and (2) the use of a spring-arch, basic roof for prolonging the life of the furnace. Although these practices can be used separately, they are generally used to complement each other in an effort to obtain minimum heat time consistent with an acceptable rate of wear of the refractory roof, walls and port ends. DECARBONIZATION BY OXYGEN INJECTION The use of oxygen to speed carbon elimination was perceived by Sir Henry Bessmer but its practical use in steelmaking could not be realized until processes were developed for the manufacture of low cost, tonnage oxygen. However, as early as 1922 Bigge1 obtained a patent covering the use of gaseous oxygen to speed decarbonization of a molten steel bath. At that time, oxygen was available only in bottles and at a cost of $240 per net ton. At the end of World War II the price of oxygen had dropped to $80 per net ton, and as a result, metallurgical oxygen (99.5 per cent began to come into widespread experimental use for decarbonization in open hearth and electric furnace shops.2-8 Even this price prevented oxygen's routine use for other than decarbonizing the bath in shops producing substantial quantities of steels containing less than 0.40 per cent carbon. Today, tonnage metallurgical oxygen can be manufactured for less than $15 per net ton, and commercial purity oxygen (95 per cent is reported to cost less than $5 per ton. Thus, it is not at all surprising to find many open hearth shops effectively using large quantities of oxygen to accelerate decarbonization. Equipment for Oxygen Injection. The oxygen may be injected by a lance pipe inserted through the wicket hole and pushed several inches into the steel bath, or by a water-cooled jet inserted through the back- wall, endwall, or roof, and immersed in the slag or set just a few inches above the slag. Oxygen at approximately 100 psi is piped directly to control stations adjacent to each furnace. The installations should include adequate safety devices such as fire checks and emergency valves,

Jan 1, 1964

I;. D. Godshall, Everett, Wash. (communication to the Secretary) : In Mr. Morse's interesting paper several statements occur which seem to require correction and comment. This is the more appropriate, since Mr. Morse has mentioned me by name, and has cited my "Review of the Russell Process,"* so that silence on my part might be taken as indicating an assent which I cannot give. On the first page of his paper Mr. Morse says that the " goingback " of chlorination was " the only difficulty encountered at Aspen," and adds that he has " never seen any explanation " of the cause. The plain inference is that he now fills this complete

Jan 1, 1896

By Hamilton Wingate

In his paper on the hydraulic mining of a low-grade gravel in California,* Mr. W. H. Radford expresses the hope that other members of the Institute will contribute, for the benefit of all, their experience in similar lines. In these notes 1 shall describe the conditions and results of the operation of the Gold Bug Mining Co., of Cleveland, O., at Georgetown, Eldorado county, Cal.

Jan 1, 1903

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who called at Institute headquarters during the period Jan. 10, 1916 to Feb. 10, 1916: William Rettie, Yonkers, N. Y. Wallace E. Pratt, Manila, P. I. R. V. Norris, Wilkesbarre, Pa. T. Skewes Saunders, El Oro, Mex. Fred MacCoy, El Oro, Mex. M. L. Requa, San Francisco, Cal. Reno H. Sales, Butte, Mont. R. W. Schultz, Ravenna, O. R. T. White, Batourn, Russia. H. J. Brown, Chester, Pa. David T. Day, Washington, D: C. A. M. Van Rensselaer, New Rochelle, N. Y. H. M. LaFollette, LaFollette, Tenn. Norman C. Stines, Russia. F. N. Speller, Pittsburgh, Pa. Howard R. Hughes, Houston, Tex. Robert W. Hunt, Chicago, Ill. C. F. Schnepp, Ridgefield Park, N. J. B. E. Fernow, Toronto, Ont., Can. George L. A. Thomson, Elizabeth, N. J. A. F. Bennett, New York City. Jasper T. Robertson, Chicago, Ill. J. C. Ralston, Spokane, Wash. J. B. Tyrrell, Toronto, Ont., Can. George J. Lyon, Schenectady, N. Y. H. G. Officer, New York Cty. Jesse C. Porter is now superintendent of the San Fernando Mine, Hoyo de Manicaragua, Santa Clara Province, Cuba.

Jan 3, 1916

by their overdogmatic picture of geology and their resulting drastic oversimplification and idealization of geologic features. I am in hearty disagreement with the recommendation that geophysics should be done by cooperative work between a geologist and a geophysi-cist. That arrangement would be comparable to doing petrography by having a physicist at the microscope and a geologist sitting by his side. The interpretation of the geological significance of geophysical data can be done efficiently only by a physicist who has become also a good geologist or by a geologist who is also a good geophysicist. Less Well-trained Men The rank and file, composing perhaps two-thirds of the personnel of exploratory geophysics, is not, and should not be, composed of highly trained men. The routine, stereotyped character of the work and the impossibility of promotion of more than a few from these lower ranks even under the best circumstances justify companies in filling the bulk of these rank and file positions with men having only a bachelor's degree at the most. There can be a wide range of training for such positions, although certain lines of study are preferred for certain kinds of work, and different employers have different preferences. For work in gravitational and magnetic prospecting, first preference will be for men having geological training and second for men with civil engineering training. In seismic work, men with geological training are preferred by some employers for computers; physicists, electrical engineers and all whose technical education has covered radio circuits are preferred for the other technical positions. Collegiate training in geophysical prospecting brings no preference and by many employers is given a slightly inferior rating. One large company seldom hires men who have just graduated with a major in geophysical prospecting. This prejudice is based on the reasoning that much of what is learned in college is obsolete or obsolescent, that most of the techniques learned in college will have to be unlearned, because different from those used by the employing company, and that in the long run additional courses in basic physics, mathematics and geology are of more value to a man than the courses on geophysical prospecting. DISCUSSION [This discussion refers to the five papers beginning on page 23 and ending on page 74.1 L. W. Blau,* Houston, Texas.—I have had some rather sad experiences with forecasting. For example, I could not foresee 10 years ago my present occupation, and I do not profess to be able to look ahead 10 years and tell anyone what he will be doing then. Referring to the point raised in the discussion, I do not know, for example, what the price of oil will be 10 years from now. If an appreciable number of

Jan 1, 1940

by their overdogmatic picture of geology and their resulting drastic oversimplification and idealization of geologic features. I am in hearty disagreement with the recommendation that geophysics should be done by cooperative work between a geologist and a geophysi-cist. That arrangement would be comparable to doing petrography by having a physicist at the microscope and a geologist sitting by his side. The interpretation of the geological significance of geophysical data can be done efficiently only by a physicist who has become also a good geologist or by a geologist who is also a good geophysicist. Less Well-trained Men The rank and file, composing perhaps two-thirds of the personnel of exploratory geophysics, is not, and should not be, composed of highly trained men. The routine, stereotyped character of the work and the impossibility of promotion of more than a few from these lower ranks even under the best circumstances justify companies in filling the bulk of these rank and file positions with men having only a bachelor's degree at the most. There can be a wide range of training for such positions, although certain lines of study are preferred for certain kinds of work, and different employers have different preferences. For work in gravitational and magnetic prospecting, first preference will be for men having geological training and second for men with civil engineering training. In seismic work, men with geological training are preferred by some employers for computers; physicists, electrical engineers and all whose technical education has covered radio circuits are preferred for the other technical positions. Collegiate training in geophysical prospecting brings no preference and by many employers is given a slightly inferior rating. One large company seldom hires men who have just graduated with a major in geophysical prospecting. This prejudice is based on the reasoning that much of what is learned in college is obsolete or obsolescent, that most of the techniques learned in college will have to be unlearned, because different from those used by the employing company, and that in the long run additional courses in basic physics, mathematics and geology are of more value to a man than the courses on geophysical prospecting. DISCUSSION [This discussion refers to the five papers beginning on page 23 and ending on page 74.1 L. W. Blau,* Houston, Texas.—I have had some rather sad experiences with forecasting. For example, I could not foresee 10 years ago my present occupation, and I do not profess to be able to look ahead 10 years and tell anyone what he will be doing then. Referring to the point raised in the discussion, I do not know, for example, what the price of oil will be 10 years from now. If an appreciable number of

Jan 1, 1940

THE CHAIRMAN.- This meeting is under the auspices of the American Institute of Mining and Metallurgical Engineers, and I think the germ of the idea originated in the steel business. Last year there was a meeting of prominent people in the steel industry with the idea of getting together and discussing practical phases of their business, so that everybody could contribute and from that there might be benefit derived for the industry. Several months ago when Mr. Bain was in Salt Lake City, he and Mr. Oldright asked me what I, as an individual, thought of it. From that originated this idea of having the copper people come together to discuss reverberatory smelting and all its phases. In starting out, it seemed the best plan to ask members what particular subjects they wished to discuss first; that is, the ones that would be considered more important. We asked Mr. Oldright, or suggested sometime ago that the meeting be postponed until May because May is a lovely month in Salt Lake. There are a number of attractive features around the city. We have a number of smelters here and I think that probably the most of the benefit will be derived from talking in an informal way and visiting the various plants around. the valley. At any rate, speaking as a resident of Salt Lake, I am glad to see all of you gentlemen here, and hope you have an interesting and instructive time. The tentative list of subjects for discussion at this conference is as follows: Construction Walls, etc. Walls, proper design and thickness of brick for various types of charging. Bottoms, construction of. Binding steel, correct weight and arrangement, where thrust of arch should be taken. Refractory materials, feasibility of using different material in various parts of the furnace. Water jackets, where applicable. Should bricks be used inside of same. Gas space, proper design for, height of roof above bath, etc. Roof Shape of Roof, in hot zone and elsewhere, longitudinally. Construction of roof, in various zones, around openings.

Jan 1, 1930

By N. J. Grant, D. S. Bloom

THE development of high temperature, high stress alloys had proceeded with such rapidity during the war, and for a short time afterward, that our knowledge of the constitution of the alloys had become seriously inadequate. To interpret correctly alloy behavior it is not only necessary to recognize the phases present, but also to know the properties of the phases under all varieties of conditions and treatments. Chromium in these high temperature alloys holds the unique distinction of being the only one element which must be present when an oxidizing or generally corrosive atmosphere is present and when a long life is desired in service. Carbon and nitrogen must also be considered where chromium is present. Carbon is always present, either as an impurity in the raw alloying elements, or as a deliberate addition agent to increase the strength. Nitrogen is generally picked up from the atmosphere during melting or may be added as an alloying element. The effect of nitrogen additions is not too dissimilar to that of carbon additions. As such, chromium carbides and nitrides become of great interest since they are present in a very large number of alloys, including alloy steels, stainless steels, super alloys, and the like. In the chromium-carbon system there are three accepted, carbides: Cr,C, Cr7C8, and Cr3C2. The existence of one more carbide, a still higher carbon form CrC, has been advanced. The phase diagrams of chromium and carbon as published by Friemann and Sauerwald² and by Tofaute, Kuttner and But- tinghaus³ -do not extend beyond the carbide Cr3C2, which contains 13.3 pct carbon; but Hatsuta has extended the diagram up to 20 pct carbon, and in doing so hypothesized, with the use of some questionable experimental results, the compound CrC. This carbide would contain 18.75 pct carbon, 81.25 pct chromium, by weight. It is further known that as the chromium carbides increase in carbon the acid resistance increases but the oxidation resistance decreases4,5 This is of great importance in high temperature alloys where time-temperature stability, as well as oxidation resistance, is of prime importance. The possible existence of a carbide of the formula CrC thus becomes of prime importance and it was considered important to recheck the chromium-carbon binary constitutional diagram for such a compound. In view of the wide spread of values listed for the melting point of chromium (1500° to 1850°C) and 1930°C8, it was considered .that the liquidus temperatures might well be redetermined more ac-

Jan 1, 1951

By R. Taggart, R. H. Ericksen, D. H. Polonis

MarTENSITIC a has been observed to form spontaneously from the retained ß phase during the preparation of thin foil specimens of metastable Ti-Cr alloys containing from 6.9 to 20 wt pet Cr. Similar spontaneous martensite reactions have been reported in thin foils of 0 brass' and other alloys.2 4 The absence of retained austenite in iron-based alloys has also been attributed to spontaneous decomposition during thinning.5 The present work indicates that a unique situation occurs during which the spontaneous transformation takes place when the transitional ? phase is present in the as-quenched or partially aged ß phase. Alloys containing 6.9, 7.0, 8.0, 12.0, and 20.0 wt pet Cr were prepared by the levitation melting of "io-chrome" chromium and iodide titanium. The 0.5-in.-diam ingots were vacuum-annealed at 1000oC, and wafers 0.020 in. thick were then cut from the ingots. These wafers were wrapped in molybdenum foil, encapsulated in Vycor under a reduced pressure of purified helium, and then held for 30 min at 1000°C. The specimens were quenched in water to retain the metastable high-temperature ß phase. The quenched alloys were thinned by mechanical grinding to about 0.005 in. thick, then electropolished in a solution of 300 ml methyl alcohol, 175 ml n-butyl alcohol, and 30 ml perchloric acid at a temperature of -40°C. Needle specimens 0.005 to 0.010 in. diam were taken from each ingot and heat-treated with the foil specimens. X-ray diffraction patterns indicated the structure of the 6.9, 7.0, and 8 wt pet alloys to be a

Jan 1, 1968

By W. A. Backofen, D. Lee

Tlze condition of superplasticity or neck-resistanl flow that results front high strain-rate sensitivity has been observed in isothermal tension tests on several titanium alloys and one of zirconium hi general, il was associated with reasonably fine-grain micro-structures being stvained in the transformation range at rates below i - 10 -3 sec-&apos;. The metallographic mean-free path, L, was measured at room temperature after rapid cooling from the temperature of test-ing. The flow stress of Ti-GAL-4V at 950°C was proportional to La at different constanl <; the value of a decreased with increasing. E but at E< 1.5 x 10-4 sec-1 it varied only from 0.9 to 1.25. The findings were interpreted to mean that viscous boundary shear is the rate-controlling process of deformation at high levels of strain rate sensitivity in these materials. Elongation of over 1000 pet could be obtained, but a1 temperatures so high and rates so low that any practical application of the full effect would probably be difficult. As the transformation range was narrowed, by turning from Ti-6AL-4V to Ti-5Al-2.5sn to nomznally pure titanium, the allowable temperature varialion was correspondingly reduced. Superplasticily was not found in Armco iron, presumably because the transformation range was too narrow to allow the developtnenl of a reasonably stable microstructure for isolhermal lesting. THE work represented by this paper grew out of a recent study of texture hardening in a(hcp) titanium and zirconium-alloy sheet,&apos; of which part has now been published.2 It was found that, with heating, the tensile plastic-anisotropy index, R,* was decreased from well above 1 towards 1 as the temperature range for the a(hcp) -ß(bcc) phase change was entered. The clearest example of that trend is illustrated with previously unpublished data in Fig. 1. It might have been thought that such a development resulted simply from introduction of the cubic and therefore plastically less anisotropic phase. However, the accompanying change in the index of tensile strain-rate sensitivity, m = a log a/a log E, was rapidly upwards, to a high of 0.85 in some cases (also illustrated in Fig. 1). At the same time, the total tensile elongation rose to a maximum and the flow strength dropped away as R (and m) approached 1. Taken together, the observations cannot be understood as resulting from the presence of cubic phase, per se. It has been concluded instead that they reflect the largely noncrystallographic deformation which characterizes superplasticity. As demonstrated in other recent work? a necessary condition for super-plasticity is strain-rate sensitivity of flow stress sufficiently high that m is above a lower limit of -0.3. The origin of large m has been traced, in turn, to grain size so small that a substantial amount of viscous deformation is introduced by such processes as Nabarro-Herring diffusional flow4 and/or grain boundary shear.5,6 Because of problems in the processing of titanium and zirconium alloys—problems of high strength, limited ductility, and excessive springback, originating largely in slip resistance-it was natural to wonder if something useful might be done with superplasticity in those materials. Therefore experiments were made for more closely identifying and generally bounding the phenomenon with temperature and strain-rate limits, before attempting to decide about its exploitation. The results are being reported here. EXPERIMENTAL Materials. The two of primary interest were the titanium alloys of nominal composition (in wt pct) 5A1-2.5Sn and 6A1-4V. Others were a 4A1-1/4O2 titanium alloy, titanium of commercial purity (RC-70), Zircaloy-4. and Armco iron. All were received as annealed 3/16 in. thick sheet, except RC-70 which was & in. thick, and tested in that condition. Details of transformation temperature and grain size are given in Table I. The results of dilatometry for the measurement of transformation temperatures were unsatisfactory. Data were finally obtained by metallographic examination of each specimen after test, to determine from the amount of transformed 4 where the specimen had been heated in relation to the critical temperatures. Results were in reasonable agreement with information from the supplier. Strip tensile specimens were of full sheet thickness and taken along the rolling direction, except for those

Jan 1, 1968

By AIME AIME

REGISTRATION and licensing of engineers is now being given consideration by a special committee of the Institute, authorized at the March meeting of the Board of Directors. The subject is one that has recently been or is now actively before engineering organizations in many of the States of the Union. In Washington, D. C., the Washington Society of Engineers and the local sections of ten national engineering societies, including the A.I.M.E., recently had a joint committee investigate the subject: this committee formulating a proposed law that has been presented to Washington engineers for their consideration. At the same time, the committee has summarized the reasons for and against registration of engineers in Washington, D. C. As many of these reasons are of more than local application, they are here reprinted so that all members of the A.I.M.E. may be informed on the subject. It is expected that some report of the Institute&apos;s Committee on Registration, State Councils and Professional Development will he made at some forthcoming meeting of the Board of Directors.

Jan 1, 1932

By E. D. Levine

A study was made to delineate the dislocation mechanistns controlling prismatic and basal slip at low temperatu.ves in titanium containing approximately 100 ppm interstitial impurities. Mechanical tests were performed on single crystals prepared from electron-beam zone-refined crystal bar by a thermal cycling technique. Measurements were made of critical shear stress and activation volume as functions of temperature. The study revealed that, for prismatic slip, two overlapping thermally activated processes aye rate-controlling below 300°K. From absolute zero to 220°K, reasonable agreement is obtained between experiment and the mechanism which involves overcoming 01. the Peierl&apos;s stress by the formation of double kinks in dislocation lines lying in close-packed directions. Between 220°and 300°K prismatic slip is controlled by a difierent thermally activated process which is characterized by a stronger temperature dependence of critical shear stress. Above 300OK, prismatic slip is controlled by an athermal process. Basal slip is controlled by a thermally activated process between 195&apos; and 400°K. An approximate analysis suggests that it is the Peierl&apos;s mechanism that is rate-controlling in this range. Below 195°K, the occurrence of mechanical twinning obscures the features of basal slip. Above &apos;400 X, basal slip is controlled by an athermal process. TITANIUM, an hcp metal with a less-than-ideal axial ratio of 1.587, deforms primarily by {1010}( 1210) slip at low temperatures.&apos;-3 The critical shear stress is strongly affected by the presence of interstitial impurities. For example, churchman3 reported that a decrease in the combined nitrogen plus oxygen content from 0.1 to 0.01 pct decreased the critical shear stress for prismatic slip from 9.19 to 1.4 kg per sq mm at room temperature. Basal slip, however, is less strongly affected by interstitials; Churchman&apos;s data for {0001}( 1210) slip show a smaller decrease in critical shear stress from 10.90 to 6.3 kg per sq mm at room temperature, for the same decrease in interstitial content. In the present study, an attempt has been made to delineate the dislocation mechanisms controlling prismatic and basal slip in titanium. In view of the strong effects that impurities may have on at least some of these mechanisms, experiments were performed on material of reasonably high purity, so that comparisons could be made with investigations on material of both lower and higher impurity contents. EXPERIMENTAL PROCEDURE Single crystals were prepared from 1/4-in.-diam electron-beam zone-refined crystal bar, furnished by Materials Research Corp. The analysis of the zone-refined material is given in Table I, indicating that the interstitial content is of the same order as the purer of the two materials investigated by Churchman. The Vickers diamond pyramid hardness number of this material was 85.6. This value agrees quite well with the correlation between hardness and interstitial content proposed by Ogden and Jaffee.4 On the basis of hardness, the material investigated in this study is, therefore, intermediate in purity between that studied by Churchman (Vpn = 97) and that studied by Spangler and Herman (Vpn = 62.4).5 Single crystals were grown by thermal cycling through the a-ß transformation. Two-in.-long by 1/2-in.-diam bars were heat-treated in vacuum for 4 hr at 1160°C. The temperature of the furnace was then lowered to 865°C, and the specimens were maintained at this temperature for 7 days. This procedure was repeated several times, resulting in the growth of individual crystals up to 14 in. in length. Specimens for testing in direct shear along either {l010}(1210) or {0001}(1210) were obtained by electrical-discharge machining. The specimens were in the form of cylinders 1/4 in. in diam by approximately 1/2 in. in length, with a reduced section 1/8 in. in diam and a in. in length. All specimens were electropol-ished subsequent to electrical-discharge machining. The ends of the test specimens were cemented in stainless-steel collars. Shear tests were conducted in an Instron Tensile Tester at various temperatures from 4.2° to 508°K. Measurements were made of critical shear stress and activation volume. The latter measurements were performed by measuring the change in flow stress upon cycling the strain rate between ?1 = 2.62 x 10-3 per sec and ?2 = 2.62 x 10-4 per sec. Activation volume, I)*, is defined as u* =ßkT [11

Jan 1, 1967

A dinner was given to Ambrose Swasey by the United Engineering Society, at the Engineers&apos; Club, on November 14. Those present -included -twenty-one presidents and past presidents of the Founder Societies. Charles F. Rand, President of United Engineering Society, presided. President Robert S. Woodward, of the Carnegie Institution of Washington, and Dr. Robert W. Hunt, of Chicago, made addresses to which Mr. Swasey responded. Dr. Michael I. Pupin, Chairman of Engineering Foundation, made the closing address. The evening was marked by the high character of the addresses, inspiration for grave duties lying before the engineering profession, and by the spirit of good fellowship. Among the seventy-two persons present were the following members of the Institute: E. E. Bartlett, William N. Best, J. Parke, Channing, C. R. Corning, F. C. Cottrell, J. V. Davies, J. V. N. Dorr, H. S. Drinker, Karl Eilers, H. M. Howe, A. C. Humphreys, Robert W. Hunt, Wm.. B. Jackson, D. S. Jacobus, J. H. Janeway, J. E. Johnson, Jr., John Johnston, George F. Kunz, Edwin Ludlow, Philip N. Moore, Fred&apos;k. H. Newell; Wm. H. Nichols, H. Hobart Porter, Charles F. Rand, R. M. Raymond, .Jesse M. Smith, E. Gybbon Spilsbury, Bradley Stoughton, . Joseph Struthers, Benj. B. Thayer, Wm. H. Wiley, S. T. Wellman.

Jan 1, 1919

By R. Taggart, D. H. Polonis, J. C. McMillan

Thin foil electron microscopy techniques have been used to study the micros tructure of a Ti- 7.5 wt pct vanadium alloy in the quenched and aged cond_itions. Selected area diffraction has identified a (1011) twinning mode accompanying the martens ite t9.an.sfo?rn~ation. Precipitation of the 0 phase during the aging of quenched alloys has been obsevced to occuv in the form of plates and needles with preferential growth along the (1120) direction in the a&apos; matrix. In the present work, the micro structures of quenched and aged alloys of the 0 isomorphous Ti-V system have been investigated by means of thin-foil electron-microscopy techniques. Most of the previous studies of martensitic phases in titanium-base alloys have utilized optical microscopy and X-ray diffraction techniques. The application of transmission electron microscopy is more recent, and only a few such studies have been reported.1-5 This paper is concerned particularly with the crystallographic nature of substructures formed in the martensitic a&apos; plates. The early stages of aging or tempering have also been examined to determine the modes of precipitation from the martensitic solid solutions. Such information is essential in studying strengthening mechanisms and in determining the feasibility of high-strength rnartensitic alloys based on titanium. Liu and Margolin6 reported several types of substructures within the martensitic plates of quenched Ti-Mn alloys. It was later suggested by Liu7 that the structure of martensitic plates might be very complex and not single crystals as normally assumed. The sub-markings could not be identified with the two possible habit-plane orientations {334}ß and {344}ß, and it was not positively determined whether they are associated with mechanical twinning. The recent studies by Armitage5 on titanium martensites in a variety of commercial alloys have indicated that twinning does not generally accompany the transformation. This observation is in accordance with the Mackenzie and Bowles model for the transformation in pure titanium8 which suggests that twinning is not to be expected. However, a number of other recent investigators have reported twinlike substructures in the martensitic plates of several titanium systems including commercia1 titanium,2,3 Ti-Cu,5,9 Ti-Ta,1 and the commercial alloy Ti-8A1-1Mo-1V. Blackburn* has reported that the structure of quenched Ti-8A1-1Mo-1V depends on the prior solution temperature. He identified two types of martensitic structures, one of which is described as a heavily faulted hcp or twinned fcc structure and the other an hcp structure with a high internal dislocation density. The latter type exhibited some twinning with a (1011) twin plane. EXPERIMENTAL PROCEDURES AND RESULTS The alloy used in the present work was a 7.5 wt pct V alloy that was prepared by conventional arc-melting techniques. This alloy composition was selected

Jan 1, 1968

By R. W. M. Lai

INTRODUCTION Manganese nodules were first discovered by the H.M.S. CHALLENGER expedition of 1873-76 and have engaged the interest of oceanographers and natural resources engineers ever since (1-4). Manganese nodules, some of them as large as grapefruit, cover vast stretches of the ocean floor throughout many parts of the world. In some areas the ocean floor is literally paved with nodules. The Pacific Ocean alone is estimated to contain 1.5 trillion tons of nodules which are forming at the rate of about 10 million tons per year (2). An analysis of the principal metal values for Pacific Ocean nodules is shown in Table I (5). [ ] The principal ingredients of the nodules are manganese and iron, but they also contain other important associated metal values such as copper, nickel, cobalt, and molybdenum. These associated metal values,

Jan 1, 1980

By A. English, M. J. Greaves

This paper is a discussion of pelletizing systems developed over the last 15 to 20 years for the agglomeration of fine iron ore concentrates. Five different pelletizing systems are now in commercial use in the U.S., and for the purposes of comparison, estimated operating costs and capital costs for the construction of four of them are included. Capacities of existing commercial plants are examined, together with the anticipated capabilities of plants presently being built or projected. In just 21 years, the art of pelletizing iron ore concentrates has reached maturity with mastery of the separation of finely divided concentrates from low-grade iron ores and their agglomeration into pellets containing about 65% iron. This accomplishment has firmly established an improved feed for the blast furnace, with resulting benefits in faster reduction of burdens and greater economy of operation. The present production capacity of pelletizing facilities in the U.S. is about 20 million tons annually, and it is expected to double by 1970. The rapid expansion of pelletizing in the U. S. has been closely observed in European countries, notably in Sweden and Germany, where pioneer agglomerating techniques were developed early in this century. PELLETIZING PLANTS AND PROCESSES Twelve commercial pelletizing plants are presently in operation in the U. S. and Canada. An equal number are in various stages of engineering and construction, and many others are being considered. The pelletizing systems currently employed include shaft furnaces, horizontal grates using three different airflow arrangements, and grate kilns. The capacity of pelletizing operations in North America is shown in Table I. All of these plants are integrated with the mine, the ore-crushing facilities and the concentrating plant and are equipped with storage and loading-out facilities for the product. Normally, a pelletizing plant is composed of a shuttle conveyor above the receiving bins; balling equipment; a heat-hardening system including the necessary auxiliaries such as furnaces, burners and controls, ducts, fans, meters and instrumentation; fines recovery equipment; and product handling equipment. Also included are the necessary auxiliaries and utilities such as boilers or power plant; oil unloading and storage facilities; coal unloading storage, grinding and distribution facilities; and bentonite or other additive storage and distribution equipment. Shaft Furnaces: Vertical shaft furnaces used in this country are limited to the treatment of natural magnetite concentrates containing minor quantities of residual fluxing elements. Fig. 1 shows a perspective view of the shaft furnace with balling, feeding and pellet-handling equipment. An elevation of a shaft furnace is shown in Fig. 2. A commercial shaft furnace unit is about 45 ft in height with a 6 x 14-ft rectangular cross section and has a nominal production rate of approximately 50 gross tons of pellets per hour. The upper portion of the furnace shaft is constructed of fire brick as protection from the high process temperatures involved. The lower portion of the shaft is lined with abrasion-resistant brick to withstand erosion from the fired pellets. Rectangular-shaped, refractory-lined and insulated combustion chambers are situated on each side of the shaft furnace. Oil or gas is burned to produce high temperature gases which are forced into the furnace through ports located near the top of the combustion chambers. The shaft furnaces operate at a pressure of approximately 6 psi. Pellets are fed into the top of the furnace by a pantographic feeder designed to produce the desired pellet stockline. The furnace is kept filled at all times and pellets are fed and discharged from the furnace at the same rate. In early development, 10 to 12 lb of solid fuel was incorporated in the pellets. However, the main source of process heat is now derived from the combustion chamber gases. In some instances no solid fuel is used. The pellet movement in the shaft furnace is counter-current to the flow of gases. Ambient air is introduced through louvers at the lower end of the furnace, at about 6 psi, cooling the fired pellets and supplementing the heat of the high temperature gases from the combustion chamber ports. The zone of maximum temperature, located above the ports of the combus-

Jan 1, 1963

By Robert E. Green, Robert A. Swanson

Ultrasonic attenuation and stress were measured simultaneously as a function of strain for aluminum single crystals tested in compression. The propagation mode and polarization of the ultrasonic waves were chosen with reference to the theoretical analysis presented in Part I. Good experimental agreement was found with this theory and with earlier experimental work in tensile tests. Support is given to the contention that ultrasonic -attenuation measurements are much more sensitive to the early stages of plastic deformation than are conventional stress -strain measurements. Dislocation meclzanisms are suggested which are compatible with both the present and the earlier experimental observations. A brief historical introduction of previous work concerned with the study of dislocation motion by ultrasonic-attenuation measurements has been given in Part I. The purpose of the present experimental investigation was to make use of the theoretical considerations from Part I in order to gain further knowledge concerning dislocation motions during plastic deformation. Emphasis was placed on the choice of propagation modes and polarization of the waves, such that interactions between these waves and dislocation movement on a specific slip system could be investigated. EXPERIMENTAL PROCEDURE Since the primary concern of this investigation was dislocation damping, other sources of damping were eliminated as much as possible. The test specimens were 0.5-in.-diam single crystals of 99.99+ pct pure aluminum grown from the melt by a modified Bridgman technique. Ultrasonic-attenuation measurements were made at a frequency of 10 megacycles per sec using a Style 56A001 Ultrasonic Attenuation Comparator manufactured by Sperry Products Inc. after a design by Chick, An- derson, and Truell.1 At this frequency the particle vibrations are essentially adiabatic and thermo-elastic damping should be absent. This frequency was selected since it was one of the frequencies used by Hikata et al.2 n conjunction with tensile tests on aluminum crystals, thus allowing direct comparison with this work. The use of quartz-crystal transducers insures that the amplitude of vibration is not sufficient to cause the break away of the dislocation loops from weak pinning points. The quartz-crystal transducers used all possessed a resonance frequency of 10 megacycles per sec and were thin circular discs 0.375 in. in diameter. X-cut crystals were used to generate the longitudinal waves and AC-cut crystals to generate the transverse waves. Aluminum was chosen as the basic material because it is a typical fcc metal whose deformation behavior is well-known and because the most recent work at the time the present research was initiated was that by Hikata et al. who used aluminum. The present tests were run in compression to see if such tests could be satisfactorily run in compression without being severely masked by grip effects.. A second reason was to compare the results in compression with those of the tension experiments of Hikata et at. Finally, shorter specimens could be run in compression with less over-all damping than in tension. All of the aluminum-crystal test specimens used were oriented for plastic deformation by single slip; i.e., they possessed the orientation having a maximum Schmid factor of 0.5. Because of the well-known time dependence 3 of plastic strain at constant stress, the test specimens were subjected to a quasi-static loading. Previous investigations4-&apos; have indicated that attenuation after plastic deformation is also time-dependent, so any continuous loading of the specimen would show that changes in attenuation were also a function of strain rate. By loading the specimen to a given stress level and holding it constant until the recovery process was essentially complete, the time dependence was eliminated. The quartz transducer was permanently bonded to the aluminum crystal using Eastman 910 cement. Excess cement was removed from around the quartz with DMF (dimethyl formamide). Eastman 910 was found to be far superior for bonding, especially with regard to the shear-wave transducer, since it formed a solid bond which readily supports shear-wave propagation. The solid bond formed by the Eastman 910 cement also insured that the quartz

Jan 1, 1964

We the undersigned, being all persons of full age and citizens of the United States and a majority residents of the State of New York, desiring to form a corporation pursuant to the provisions of the Membership Corporations Law for the purpose of incorporating, as provided in Section 5 of Article I. of said law, the existing unincorporated association known as American Institute of Mining and Metallurgical Engineers, Incorporated, do hereby make, acknowledge and file this Certificate for that purpose, and do Certify as follows: I. That the American Institute of Mining Engineers is an unincorporated association organized and existing with the object of promoting the arts and sciences, connected with the economic production of the useful minerals and metals and the welfare of those employed in these industries by means of meetings for social intercourse and the reading and discussion of professional papers, and to circulate by means of publications among its members and associates the information thus obtained. II. That the persons duly appointed or designated to manage the affairs of said association are designated by the rules thereof Members of its Council; that the undersigned are all members of said Council as the same was constituted on the 29th day of December, 1904. III. That on said last-mentioned date a regularly called meeting of said association was held at its office in the Borough of Manhattan, City of New York; that thirty days before such meeting notice of the intention to incorporate said association was given by mail to each member thereof whose residence or post-office address is known; that at said meeting the following resolutions were offered, seconded and duly adopted by the unanimous vote of all its members then present, to wit: "Resolved, That it is the sense of the members and associates of the American Institute of Mining Engineers in general meeting assembled that it is desirable and necessary for the well being of said association and its members and for the furtherance of the objects for which the same has been formed, that said association incorporate under the Membership Corporations Law of the State of New York; "And Further Resolved, That the Members of the Council of this Association, or a majority thereof, be and they hereby are authorized, in accordance with the provisions of Section 5 of Article I. of the Membership Corporations Law, to incorporate this association for the same purposes for which it has been organized and conducted, in the manner provided in Article II. of said law;, "And Further Resolved, That the name of said corporation as hereby adopted by this meeting shall be American Institute of Mining Engineers; "And Further Resolved, That the said incorporators shall be named in the Certifi¬cate of Incorporation as directors of such corporation until its first annual meeting,

Jan 1, 1940

By Roger V. Pierce

INTRODUCTION IN the last few years, much study has been devoted to increasing stoping efficiency. The reasons for this are shortage of manpower, shorter working hours, operating regulations, and shortages of essential materials. More efficiency in mining methods is needed to offset these adverse factors. In the past, attention has been centered upon haulage, hoisting equipment, mill flowsheets, etc., but recently the spotlight has been focused on the cost of stoping and the cost of handling materials. Scrapers and scraper hoists have thus assumed greater importance. In order to make it possible for certain ore bodies to be mined at a profit, it has been necessary to apply assembly-line practices to the streamlining of mining methods. All cycles of the mining operation must balance, and the sooner broken ore is removed from the working face, the sooner another round can be started. Since the introduction of scraper hoists in metal mines more than thirty years ago, much progress has been made in their design and application. Alert operators are now constantly watching for methods in which to apply scrapers. The saving of manpower in development work and the changing of mining methods that once employed manual handling of materials are increasing vital wartime tonnages. Essential ores from newly discovered ore bodies are moving rapidly from stopes to reduction plants-because it is now possible to develop an ore body and place it in production with a minimum of manpower and development work. Today, speed is one of the prime essentials of mining. Everywhere, there is a concentrated effort to use experienced miners in breaking rock, in timbering, and in carrying out the various phases of mining that require many months of training. Much effort is being made to mechanize the working places because experienced men naturally prefer to work where the majority of materials are handled mechanically. In line with this policy, many new men are being taught the details of scraper work, because even green men can quickly become acquainted with scrapers and thereby release older heads to perform the more skilled phases of mining. In some places it has been found economical to change from one system of stoping to another that more readily allows the application of mechanical muck-handling equipment. Where blocks are worked faster, the cost of materials, time, and labor is cut drastically. This favorable situation allows more manpower to remain on straight breaking and timbering-or straight production mining. More-over, when blocks are mined faster, more floors can often be mined vertically before the mucking or wheel floor is moved. This results in several direct savings. There are cases where it has been proved that by working a given block faster more area, longitudinally or vertically, could be mined at one time, thus permitting the reduction of development cost. (Fig. I.)

Jan 1, 1943

By James P. Savely, Victor L. Kastner

Inspiration Consolidated Copper Company is currently mining in four pit areas; Live Oak, Red Hill, Thornton and Joe Bush Extension, near Globe, Arizona. Small satellite orebodies lying outside the main pits have been mined out in a series of small open pits. Major slope instability has affected production in every pit. Some consequences of the instability have been; (1) Serious interruption of mining plans, which resulted in deferred ore production, lost ore, reduced mining rates and increased stripping requirements. (2) Forced replacement of crushing facilities. (3) Serious effects on other production facilities. The introduction of a slope stability monitoring and control function as an integral part of mine planning has been successful in reducing the impact of these failures and will eventually result in economic pit design based on probabilistic slope analysis. This case history presents a brief review of the problems associated with slope instability at Inspiration&apos;s mines followed by a more detailed report on one specific failure area in the Thornton pit where the use of horizontal drain holes for slope stabilization appears to be successful. Relationships between slope movement rate, rainfall, and mining activity are shown.

Jan 1, 1983