Search Documents

By Charles Becker

THE practice of drying phosphate in Florida is as old as the industry, which began a little more than half a century ago. The methods, however, have changed considerably. At first, the natural process of exposure to the sun and air was used, later supplemented by wood fires beneath open-air stationary dry kilns and drying towers of various designs. It was not until the early nineties that rotary driers came into use, and at first they were of very small design and fired with wood. As the industry grew and tonnage increased, so likewise grew the number and size of rotary driers, until today the largest installations are 6 ft. up to 7 ft. 6 in. in diameter, and 55 to 60 ft. long, fired with crude oil. The reasons for drying phosphate rock are: (1) to eliminate freight on water in the shipment and (2) to facilitate the good grinding qualities required by the buyers in their acidulation. Phosphate pebbles vary materially in natural characteristics and each property has a direct bearing on the processing. In making comparisons of cost and operating conditions, the following are usually taken into consideration: 1. The hard dense pebbles, which contain very little interior moisture and 6 to 8 per cent total moisture, usually produced from the low-grade deposits. 2. The lighter, porous pebbles, which contain 4 to 5 per cent interior moisture and a total moisture ranging from 9 to 15 per cent. 3. The product of recovery operations using oily reagents, containing from 15 to 25 per cent moisture. 4. The size of the pebbles. Usually the plus 5-mesh material is considered as "coarse rock"; the minus 5-mesh plus 24-mesh is "fine rock," and the minute particles below 24 mesh are called "concentrate." 5. The amount of moisture allowed in the dried product. The practice is generally to dry down to 1.5 to 2 per cent moisture. There is, however, an actual range in guarantee of from 1 per cent maximum to 3 per cent maximum.

Jan 1, 1936

By Charles N. Becker

The practice of drying phosphate in Florida is as old as the industry, which began a little more than half a century ago. The methods, however, have changed considerably. At first, the natural process of exposure to the sun and air was used, later supplemented by wood fires beneath open-air stationary dry kilns and drying towers of various designs. It was not until the early nineties that rotary driers came into use, and at first they were of very small design and fired with wood. As the industry grew and tonnage increased, so likewise grew the number and size of rotary driers, until today the largest installations are 6 ft. up to 7 ft. 6 in. in diameter, and 55 to 60 ft. long, fired with crude oil. The reasons for drying phosphate rock are: (1) to eliminate freight on water in the shipment and (2) to facilitate the good grinding qualities required by the buyers in their acidulation. Phosphate pebbles vary materially in natural characteristics and each property has a direct bearing on the processing. In making comparisons of cost and operating conditions, the following are usually taken into consideration: 1. The hard dense pebbles, which contain very little interior moisture and 6 to 8 per cent total moisture, usually produced from the low-grade deposits. 2. The lighter, porous pebbles, which contain 4 to 5 per cent interior moisture and a total moisture ranging from 9 to 15 per cent. 3. The product of recovery operations using oily reagents, containing from 15 to 25 per cent moisture. 4. The size of the pebbles Usually the plus 5-mesh material is considered as "coarse rock"; the minus 5-mesh plus 24-mesh is "fine rock," and the minute particles below 24 mesh are called "concentrate." 5. The amount of moisture allowed in the dried product. The practice is generally to dry down to 1.5 to 2 per cent moisture. There is, however, an actual range in guarantee of from 1 per cent maximum to 3 per cent maximum.

Jan 1, 1938

By Charles N. Becker

The practice of drying phosphate in Florida is as old as the industry, which began a little more than half a century ago. The methods, however, have changed considerably. At first, the natural process of exposure to the sun and air was used, later supplemented by wood fires beneath open-air stationary dry kilns and drying towers of various designs. It was not until the early nineties that rotary driers came into use, and at first they were of very small design and fired with wood. As the industry grew and tonnage increased, so likewise grew the number and size of rotary driers, until today the largest installations are 6 ft. up to 7 ft. 6 in. in diameter, and 55 to 60 ft. long, fired with crude oil. The reasons for drying phosphate rock are: (1) to eliminate freight on water in the shipment and (2) to facilitate the good grinding qualities required by the buyers in their acidulation. Phosphate pebbles vary materially in natural characteristics and each property has a direct bearing on the processing. In making comparisons of cost and operating conditions, the following are usually taken into consideration: 1. The hard dense pebbles, which contain very little interior moisture and 6 to 8 per cent total moisture, usually produced from the low-grade deposits. 2. The lighter, porous pebbles, which contain 4 to 5 per cent interior moisture and a total moisture ranging from 9 to 15 per cent. 3. The product of recovery operations using oily reagents, containing from 15 to 25 per cent moisture. 4. The size of the pebbles Usually the plus 5-mesh material is considered as "coarse rock"; the minus 5-mesh plus 24-mesh is "fine rock," and the minute particles below 24 mesh are called "concentrate." 5. The amount of moisture allowed in the dried product. The practice is generally to dry down to 1.5 to 2 per cent moisture. There is, however, an actual range in guarantee of from 1 per cent maximum to 3 per cent maximum.

Jan 1, 1938

By C. G. Dunn, F. Lionetti

W. G. BURGERS*—It seems almost certain that this investigation shows the way which finally, when more analogous data have been obtained, must lead to the understanding of many features of preferential growth-directions of crystals and of the occurrence of recrystallization textures. In this connection I should like to mention that Mr. Tiedema in my laboratory succeeded in developing an analogous method for preparing crystals in aluminum plates with a chosen crystal-lographic plane and direction parallel to the surface of the plate (to be published in Cryst. Ada). If such crystals were grown in high purity aluminum and test-pieces containing a few crystals such as the authors describe were prepared for this metal, it might be possible that due to the absence of growth obstructing particles, even in this low-melting point metal boundary displacements approaching equilibrium positions might be realized. With regard to the apparently marked drop in surface energy for orientation differences approaching zero degree, and orientation differences approaching those existing between twins, it seems of interest to remark that in aluminum a crystal growing at the expense of fine grained material cannot (or can only very reluctantly) absorb grains in either ap- proximately (within 5—10°) parallel or spinel twin orientation (May, Tiedema and Burgers, Nature (1948) 162, 740 and Cryst. Ada in press). Consequently with aluminum the method of preparing a crystal with a definite orientation does not succeed when the new crystal has to absorb its own texture; for example it is not possible to grow in a polycrystalline wire with a [lll]-texture a crystal with a [11 Indirection parallel to the wire axis (Tiedema: Cryst. Ada, in press). Finally I should like to mention the well-known fact (Burgers: Proc. Acad. Amsterdam (1947) 50, 723) that prolonged annealing of recrystallized nickel-iron sheet with cube-texture never succeeds in transforming this into one single crystal of the same orientation; if, by "secondary re-crystallization," large crystals are formed

Jan 1, 1950

By Charles Becker

THE practice of drying phosphate in Florida is as old as the industry, which began a little more than half a century ago. The methods, however, have changed considerably. At first, the natural process of exposure to the sun and air was used, later supplemented by wood fires beneath open-air stationary dry kilns and drying towers of various designs. It was not until the early nineties that rotary driers came into use, and at first they were of very small design and fired with wood. As the industry grew and tonnage increased, so likewise grew the number and size of rotary driers, until today the largest installations are 6 ft. up to 7 ft. 6 in. in diameter, and 55 to 60 ft. long, fired with crude oil. The reasons for drying phosphate rock are: (1) to eliminate freight on water in the shipment and (2) to facilitate the good grinding qualities required by the buyers in their acidulation. Phosphate pebbles vary materially in natural characteristics and each property has a direct bearing on the processing. In making comparisons of cost and operating conditions, the following are usually taken into consideration: 1. The hard dense pebbles, which contain very little interior moisture and 6 to 8 per cent total moisture, usually produced from the low-grade deposits. 2. The lighter, porous pebbles, which contain 4 to 5 per cent interior moisture and a total moisture ranging from 9 to 15 per cent. 3. The product of recovery operations using oily reagents, containing from 15 to 25 per cent moisture. 4. The size of the pebbles. Usually the plus 5-mesh material is considered as "coarse rock"; the minus 5-mesh plus 24-mesh is "fine rock," and the minute particles below 24 mesh are called "concentrate." 5. The amount of moisture allowed in the dried product. The practice is generally to dry down to 1.5 to 2 per cent moisture. There is, however, an actual range in guarantee of from 1 per cent maximum to 3 per cent maximum.

Jan 1, 1936

By AIME AIME

As already announced, the XCIIId meeting of the Institute will be held at Toronto, beginning July 23, 1907. Hotel Headquarters will be at the King Edward Hotel, in which also the sessions will be held. The Queens, Rossin, Wallen, Iroquois and Palmer are good hotels not far from the King Edward. Members must secure their hotel-accommodations beforehand, by direct correspondence with the hotel they select. For those who neglect this precaution, the Local Committee will doubtless do what it can, but is unable to promise anything. Correspondence concerning this meeting (including notices of intention to attend it) should be addressed hereafter exclusively to Mr. W. G. Miller, Provincial Geologist, Bureau of Mines, Toronto, who is the representative of the Local Committee. The excursion to Cobalt, Lake Tenagami, Sudbury, etc., arranged by that Committee, involves the use of a special Pullman train for meals and lodging. After waiting a reasonable time to hear from members, the Local Committee has made its contract for Pullman cars. According to its latest report, there was still room for additional excursionists. Under this head, application made immediately to Mr. Miller may not be too late. Sessions for the presentation of papers, etc., will be held at the King Edward Hotel on Tuesday afternoon, July 23, and Wednesday morning and afternoon, July 24. The following papers have been accepted: 1. Sonic Reflections on Secrecy in the Arts, by James Douglas, New York, N. Y. .2. The Wilfley Table, by R. H. Richards, Boston, Mass. 3. The Tar-Sands of the Athabaska District, by' Robert Bell, Ottawa, Can. 4. The Occurrence of Nickel in Virginia, by Thomas L. Watson, Blacksburg, Va. 5. Coal-Briquetting in the United States, by E. W. Parker, Washington, D. C.

Jul 1, 1907

By John V. Beall

Hard as the Revett quartzite are conditions governing the deep mines of the Coeur d'Al6ne. In fourscore years of mining, heat and pressure have been the rewards of preseverance. Such obstacles are the natural concommitant to search for ore at depth. But high cost and shortage of miners is a creeping frustration of the decade. These grim observations were made on a trip to the mines of the Coeur d'Al6ne in the first week of May. But the bouncy optimism of competent mining engineers and geologists overrides by far the tough conditions. This is the story of what they are doing. I think they are setting the stage for the wonder mines of tomorrow. I didn't meet all the people or see all the mines, so there are unfortunate gaps in the story. Then too, sometimes the muck and water blotched my notes, or I couldn't write fast enough or I was too tired. No matter. There is much to tell and, because it is basically a human story, I am flouting the rules of technical journalism and couching it in the neglected "I" person. First then, a little history . . . .

Jan 7, 1966

By A. T. Tye

REGARDING the results of preferential flotation at Cananea, Weinig has stated that "The concentrating mill of the Cananea Consolidated Copper Company at Cananea, Mexico, furnishes an excellent example of modern flotation practice. The complete figures are given because they present so forcibly the advantages of modern selective flotation."' L. O. Howard notes that "Perhaps the outstanding example so far published of improvements in results through the use of selective flotation is that at Cananea, Mexico." The following notes indicate the conditions under which the results were obtained at Cananea; also the effect of preferential flotation at the concentrator and at the smelter. In the majority of cases the full benefit of selective flotation is not fully realized, as the concentrates are shipped from the mill to smelters owned by other companies. The saving made at a certain concentrator by this method of flotation may be well understood but the saving resulting at the smelter from the results of preferential flotation at the mill is not so apparent, as the data are contained in the smelting records of some other company. Even at the smelter the great gains following preferential flotation may not be noted, as a variety of ores and concentrates from various sources are received and the difference from the changed concentrator operations of a certain mill may be obscured. As noted by Professor Weinig and Professor Howard, the results obtained at Cananea brought about a veritable metallurgical revolution at the smelter. There are probably plants at which a better preferential separation is being made than at Cananea. Many ores contain barren iron pyrite which, when depressed, does not carry copper into the tailing. Some concentrators use clean uncontaminated water for milling and in others the ore is ground much finer than at Cananea. All of these items are concerned in perfect separation. The details of preferential flotation at Cananea, therefore, are not presented on account of the perfection of the

Jan 1, 1928

By L. Webster Wickes

The bad effects of arsenic in commercial copper are well-known to metallurgists. The refining of copper by electrolysis eliminates practically all of the arsenic, provided certain requirements are fulfilled. The first, and most important, of these requirements is, that the voltage of the depositing current shall not be too high. It has been known for some time that the percentage of arsenic in the deposited copper increases with the voltage. To investigate the relation between the electro-motive force (e.m.f.) and the freedom of the precipitated copper from arsenic, the experiments were made, of which a brief summary is here given: I made three copper-arsenic alloys, containing respectively 3.56, 2.24 and 0.96 per cent. of arsenic. From these alloys I cast several anodes. For cathodes I used sheets of thin copper,

Jan 1, 1905

By M. Sheffield

This paper presents a technique lor predicting the flow of oil, gas and water through a petroleum reservoir. Gravitational, viscous arid capillary lorces are considered, and all fluids are considered to be slightly compressible. Some theoretical work concerning the fluid flow in one-, two- and three-space dimensions is given along with example performance predictions in one- and two-space dimensions. INTRODUCTION Since the introduction of high speed computing equipment, one of the goals of reservoir engineering research has been to develop more accurate methods of describing fluid movement through underground reservoirs. Various mathematical methods have been developed or used by reservoir engineers to predict reservoir performance, 193-5,7,8 The work reported in this paper extends previously published work on three-phase fluid flow (1) by including a rigorous treatment of capillary forces and (2) by showing certain theoretical mathematical results proving that these equations can be approximated by certain numerical techniques and that a unique solution exists. DISCUSSION The method of predicting three-phase compressible fluid flow. in a reservoir can be summarized briefly by the following steps. 1. The reservoir, or a section of a reservoir, is characterized by a series of mesh points with varying rock and fluid properties simulated at each mesh point. 2. Three partial differential equations are written to describe the movement at any point in the reservoir of each of the three compressible fluids. All forces influencing movement are considered in the equations. 3. At each mesh point, the partial differential equations are replaced by a system of analogous difference equations. 4. A numerical technique is used to solve the resulting system of difference equations. Capillary forces have been included in two-phase flow calculations.1,4,8 The literature, however, does not contain examples of prediction techniques for three-phase flow that include capillary forces. Where capillary forces are considered, each of the three partial differential equations previously discussed has a different dependent variable, namely pressure in one of the three fluid phases. Therefore, three difference equations must be solved at each point in the reservoir. Where large systems of equations must be solved simultaneously, an engineer might question whether a unique solution to this system of equations actually exists and, if so, what numerical techniques may be used to obtain a good approximation to the solution. It is shown in the Appendix that a unique solution to the three-phase flow problem, as formulated, always exists. It is also shown that several methods may be used to obtain a good approximation to the solution. The partial differential equations and differenceequations used are shown in the Appendix. Matrix notation has been used in developing the mathematical results. Two sample problems were solved on a CDC 1604. They illustrate the type of problems that can be solved using a three-phase prediction technique. SAMPLE ONE-DIMENSIONAL RESERVOIR PERFORMANCE PREDICTION A hypothetical reservoir was studied to provide an example of a one-dimensional problem that can be solved. Of the several techniques available, the direct method of solution as shown in the Appendix was used. The reservoir section studied was a truncated, wedge-shaped section, 2,400 ft long, with a 6' dip. (A schematic is shown in Fig. 1.) This section was represented by 49 mesh points, uniformly spaced at 50-ft intervals. The upper end of the wedge was 2 ft wide, and the lower end was 6 ft wide. The section

Jan 1, 1970

By C. B. Alcock, R. A. Oriani

Some simple models of solutions are described; these include the regular solution, the subregular solution, and the quasichemical model. The assunzption underlying these models, the physical signzficance thereof, and the experimental manifestations are discussed. Examples are presented from the fields of liquid and solid metallic solutions, liquid slags, mattes, liquid and solid ionic solutions, and mixed carbides to show under what conditions and for which systems these solution models are fair descriptions. The deviations of real solutions from the models are of theoretical interest. Some such deviations, both for dilute and for concentrated solutions, arc pointed out and their Physical sigtzzficance discussed. DURING the past half century there has been a gradual accumulation of thermodynamic data for systems of interest to the metallurgist. There remain many gaps in the data, however, and the metallurgist must often face the problem of estimation of thermodynamic quantities where measured values do not exist. One might hope that the experimental progress would be matched by theoretical advances which would make such estimations possible with a high degree of confidence. However, theoretical progress has been disappointingly slow even for the simplest kinds of solutions, and since the multicomponent systems in which the metallurgist is interested are very complex, one cannot expect theory to be of much help to the metallurgist. In this situation, therefore, it seems worthwhile to examine some simple models of solutions from two points of view: firstly, to see if such crude models represent the thermodynamic facts in as many types of solutions as possible sufficiently well for the needs of the metallurgist, and secondly to see what the deviations from such models show to be important for consideration by theorists. BOND ENERGY MODELS OF SOLUTIONS The simple models that we will examine from these points of view may be termed statistical models, in that they are concerned with the thermodynamic consequences of some simple assumptions about the energy of an assembly of atoms, molecules, or ions, and do not inquire into the physical basis of the interaction. The underlying assumption of these models is that the energy of an assembly of molecules (by which we include also atoms or ions) is given by the sum over all interaction energies of molecules taken two at a time; we will discuss only those models in which the pairwise interactions are restricted to those between nearest neighbors. Thus, in a pure substance of bond energy EAA, the internal energy (with respect to some specific reference state) will be expressed as NAA EAA where NAA is the number of nearest-neighbor pairs. A solution of molecules A and B will be characterized by NAA EAA + NBB EBB + NAB EAB where the Eij represent the bond energies of the nearest-neighbor i-j pairs. If one assumes that the EAA and EBB are the same in the pure components as in the solution, and that the coordination numbers in the two pure substances and in the solution are the same, then the energy of the solution with respect to the pure components (i.e., the energy of solution) is a function of the following linear combination of the bond energies: EAB - 1/2(EAA +EBB) = w. The thermodynamically ideal solution is defined as one in which the activity of each component is equal to the mole fraction of that component at all concentrations and all temperatures. It follows that

Jan 1, 1962

By S. Frederick Ravitz

JUDGING from the inquiries that are constantly being received by the Utah Engineering Experiment Station as to the "Why," so to speak, of the flotation process of concentrating minerals, it occurred to me that perhaps a brief statement of the more important theories might interest those who have not followed the technical literature. Like many other industrial processes, flotation has hitherto been developed on an almost purely empirical basis, with relatively little practical contribution from the fundamental chemistry and physics on which the phenomena are based. In fact, its development by the trial - and - error method has been perfected to such a high state that it is becoming generally thought that further important advances can be brought about only by a thorough understanding of the actual mechanism of the process. Natur¬ally, such a complicated process has brought forth numerous theories, most of which have failed to withstand the test of time. It is significant that no theory has yet been advanced which is universally accepted.

Jan 1, 1933

By George B. Clark

Many basic engineering principles of all four phases of mining operations, namely, prospecting, exploration, development, and exploitation, can be analyzed better in terms of quantitative geology. Geological data from both field and laboratory will also complement scientific methods now being developed. THE geological data emphasized so successfully in prospecting for new deposits, that is, structural controls, strength of solutions, and type of mineralization, are basically those required for successful exploitation. In the mining of newly discovered deposits the most economical methods should be employed as early as possible to keep the overall cost per unit produced at a minimum and to permit maximum extraction of valuable minerals. A crucial question is: How can geological data be translated into useful quantitative results which will aid in achieving this end? H. E. McKinistry' has suggested that a solution may be reached in one of two ways: 1—the usual approach, use of judgment based on experience; or 2—mathematical calculations and tests on models, both subject to certain limitations. He also suggests that in addition to better use of geology more case data and theoretical data are needed on which to base sound judgment. Further research, therefore, is necessary. Perhaps in this field the emphasis should be on more specialization in mining methods and ground movement by men with thorough training in physics, engineering, geology, and underground mining. These specialists would be equipped to point out the most economical and scientific methods of exploitation. Selection of a stoping method is governed by the amount and type of support a deposit will require in the process of being mined, or by the possibility of employing the structure of the deposit to advantage in mining the ore by a caving method. In addition to these factors there are others which almost invariably influence the choice of an economical method of mining:' 1—strength of ore and wall rocks; 2—shape, horizontal area, volume, and regularity of the boundaries of the orebody, and thickness, dip and/or pitch of the deposit and individual ore shoots; 3—grade, distribution of minerals, and continuity of the ore within the boundaries of the deposit; 4—depth below surface and nature of the capping or overburden: and 5—position of the de- posit relative to surface improvements, drainage, and other mine openings. In the final analysis it is usually necessary to disregard the less important of these factors to satisfy the requirements of the more important. Because of the variation of geological conditions throughout and surrounding the deposit, no mining method will be everywhere ideally applicable to the conditions encountered in one ore deposit. The immediate problem is to interpret the above physical characteristics of deposits in terms of geological characteristics. Very few quantitative geological data are available on the factors related to a choice of mining methods. However, there are many descriptive data in mining and geological literature which collectively show how important an effect details of geology have upon all phases of mining operations. The following categories of basic mining methods were investigated to establish the geological factors that have affected their successful application: 1— open stopes with pillars; 2—sublevel stoping; 3— shrinkage stoping; 4—cut-and-fill stoping; 5— square-set mining; 6—top slicing and sublevel caving; and 7—block caving. It should be noted that the first five of these methods are listed in the order of increasing support requirements. Mines were selected as examples only where geological descriptions were complete enough to warrant their use. A study of the geological factors involved in mining operations led to a choice of the following classifications, employed in Table I: 1—structural type of orebody; 2—dimensions (geometry); 3— country rock (type); 4—faulting, folding, and fracturing; 5—alteration of ore and rock; 6—type of mineralization; and 7—geological factors determining mining method (summary). Of these factors only one yielded results that can be defined from available data in a quantitative manner, i.e., dimensions of the deposit. These are the most reliable guides that can be used in selection of suitable mining methods. They are, in general, the properties of geologic structure most difficult to evaluate by studies of models, pho-toelastic studies, and other laboratory methods, all of which are at present more limited in their applications than the geologic method. Application of geology has proved a reliable guide in other phases

Jan 1, 1955

By W. H. McFarland

The mechanical properties have been determined for a large number of alloy-free martensitic steels with carbon contents ranging from 0.08 to 0.20 pct and with manganese contents of about 0.4 to 0.5 pet. These steels were tested 1) as water-quenched, 2) after quenching, temper rolling, and tinning, and 3) after tempering treatments which involved temperatures from 400o to 1300oF and times from 1 min to 8 hr. The majority of these tests represent steel from commercial-size coils, i.e., strip 32 in. wide, coil weights up to 20,000 16, and steel thicknesses from 0.0055 to 0.024 in. As a result of these treatments, it has been shown that as-quenched low-carbon alloy-free steels can be produced with tensile strengths ranging from 140,000 to 220,000 psi and tensile elongations from 3.0 to 4.0 pet in 2 in. The tensile strength of the as-quenched martensites can be represented by the equation, tensile strength (ksi) = 119 + 560 (wt pet C). The response to tempering of these steels is related to previous work by Muir, Averbach, and Cohen and by Grange and Baughman. Strain aging of low-carbon martensite has also been investigated. If low-carbon steels are defined as those steels with a maximum carbon content of 0.2 pet, it is found that the literature on low-carbon, alloy-free martensites contains little data on the mechanical properties of these steels. However, the following facts concerning low-carbon alloy-free martensites seem firmly established:'-' 1) The major factors in controlling the strength of the martensite appear to be a) fine structure, b) the internal strain resulting from the transformation, and, particularly, c) the amount of carbon in solid solution. 2) In low-carbon steels, the martensite is auto-tempered and is in the form of needles with only minor amounts of internal twinning, whereas the martensite in high-carbon steels forms as plates which are internally twinned on a fine scale. 3) Care must be taken in comparing the results of work that has been done on low-carbon steels with varying amounts of alloying elements to data on plain carbon steels. As has been noted by Irvine, Pickering, and Garstone,6 alloying elements generally lower the martensite start temperature and, thereby, decrease the amount of auto tempering obtained during the quench. This makes it difficult to

Jan 1, 1965

By W. V. Green

The creep-rupture behavior of commercial powder-metallurgy tungsten rod is reported for temperatures of 2250°, 2500°, 2700°, and 2800°C, stresses up to 7000 psi, and times up to 4 hr. The temperature dependence and the stress dependence of creep rates are evaluated. Rupture time is fitted to the Larson-Miller parameter and compared to lower-temperature and higher stress results reported by pugh.4 THE tensile strength of single-crystal wire1 and of polycrystalline wire2 have been measured by Goucher. More recently Bechtold3 and pugh4 have studied the mechanical properties of tungsten rod between room temperature and 1200°C. Since tungsten has the highest melting point of all metals, it should retain useful strength to very high temperatures, and should find many applications in missiles, rockets, and so forth. Therefore, the mechanical usefulness of polycrystalline tungsten rod was investigated in the 2250" to 2800°C temperature range by short-time creep-rupture tests. MATERIALS TESTED Creep specimens were machined from 1/2-in. round commercial tungsten rod which was manufactured from powder by cold pressing, sintering, and hot swaging. Purity reported by the vendor was 99.95 pct W. Spectrochemical analyses showed "traces" (less than 0.01 pct) of silicon, iron, and titanium, and "faint traces" (less than 0.001 pct) of calcium and manganese. Carbon content was 30 ppm and nitrogen content was 70 to 110 ppm. No oxygen analysis was obtained. Room-temperature stress-strain tests on the as-received tungsten gave badly scattered results. Threaded end specimens broke at the threads. When these specimens were retested using shoulder grips, the specimens broke at the shoulders. No fractures occurred in the gage lengths. The fracture stresses were: 127,000; 137,000; and 154,000 psi for three specimens which fractured at the shoulders. The microstructure of the as-received tungsten rod is shown in Fig. 1. SPECIMENS USED Fig. 2 shows the two types of creep specimens tested. The threaded-end type specimen, which was used in most tests, had a 3/4-in. gage length and 1/4-in. gage diam. The cone-end specimen, which was used primarily to investigate the effects of a smaller gage diameter and the practicability of the modified grips and specimen, had a 3/4-in. gage length and a 1/8-in. gage diam. In both cases, the gage length terminated at 0.005-in. high shoulders which served as fiducial marks for optical strain measurements. Surface finish on the gage length was 16 µ-in. rms. Creep rates and rupture times were not significantly different for the two types of specimens and were not affected by electropolishing the specimens before testing. TESTING PROCEDURE The constant-load creep-testing machine used has been described by Smith, Olson, and Brown.5 In it the specimen is held vertically by grips of similar material and on the axis of a cylindrical tungsten or tantalum heater-tube. The specimen is loaded by means of the specimen grips, a pull rod (which is sealed to the chamber lid by a vacuum-tight bellows), a mechanical lever system, and hanging dead weights. Both specimen and grips are heated by radiation from the heater-tube, which is heated by its own electrical resistance. An optical system views the incandescent specimen through slits in the radiation shielding and heater-tube. The optical system projects an enlarged image of the specimen gage length on a ground-glass screen. Periodic gage-length measurements are made on this image with two cathetometers. Thorium oxide coatings on the specimen threads or conical end surfaces completely prevented diffusion-welding of specimens to grips, and were used

Jan 1, 1960

By P. Martinez, A. F. Hoyte, F. E. Senftle

The possibility of applying a neutron activation technique for silver exploration is considered. A mobile positive-ion accelerator type neutron source is used to irradiate a small area of rock or soil in situ. By using a short period of irradiation and gamma ray spectral analysis, a technique is shown for silver exploration. Two different mobile units are described. Laboratory and preliminary field tests both indicate that a sensitivity of less than 1 oz of silver per ton of ore can be achieved. The increasing consumption of silver for industrial uses and also for coinage has caused a serious shortage of silver in this country. The silver shortage has been reviewed and analyzed by kiilsgaard1 who concludes that, "The best hope for meeting future demands for silver is through accelerated exploration for precious ores." As almost all the exposed "bonanza" type silver deposits evidently have been found, it is urgent that some sensitive geophysical technique be found to detect large, extended, but generally low-grade, secondary ores, as well as hidden vein deposits. Silver is easily made radioactive by exposure to slow neutrons; hence a neutron activation method appears promising for locating silver deposits. The principles of mineral beneficiation using neutron activation techniques were discussed some years ago.2-4 Using the same approach, a preliminary description5 has been published of neutron activation as a mineral exploration tool. An exploration technique is described in which silver is made radioactive in situ and detected with a gamma radiation counter. The technique is similar to the well-known method used for uranium exploration. THEORETICAL CONSIDERATIONS Elemental silver consists of two isotopes, Ag107 and Ag109, having naturally occurring isotopic abundances of 51.4% and 48.6%, respectively. For short periods of irradiation of silver by thermal neutrons, the long-lived 250 day, half-life isotope, Ag110m, is not produced in significant quantities. However, significant quantities of 2.3 min half-life Ag108 and 24.5 sec half-life Agl10 are formed by the following reactions. Ag108 and Agl10 emit a 0.44 Mev (million electron volts) and a 0.66 Mev gamma ray, respectively. Ag107 + n + Ag108 (2.3 min) Ag109 + n + Ag110 (24.5 sec). Because of the large capture cross section (110 barns) of Ag109, and short half-life of Ag110 (24.5 sec), the 0.66-Mev gamma ray is the most prominent emission from silver for neutron activation periods of about a minute's duration.* The 0.44-Mev gamma ray from Ag108 will also be present, but will be one or two orders of magnitude lower in intensity. The decay scheme of Ag110 is shown in Fig. 1. If the neutron irradiation time is limited to about 100 sec, the Ag110 activity will essentially reach saturation and can be used to detect the presence of silver. In a neutron flux of 10 8 neutrons/cm2/set, the induced 0.66-Mev activity in 1 g of silver will be about 2 x 107 disintegrations per sec. This is about 1000 times the measurable gamma activity of 1 g of uranium in equilibrium with all its decay products; hence there is ample activity for detection. Under the same conditions of activation, most of the other elements do not reach this relatively high disintegration rate. Although this is in favor of the proposed technique, other problems must be considered. For mobile operation, it is desirable to obtain the largest neutron flux to weight ratio. Hence we have used a small 150-kev accelerator-type neutron source rather than an isotopic source such as an americium-beryllium neutron source. By use of remote control system, an accelerator-type neutron source can be safely used without the massive shield required for an isotopic source. Moreover, an accelerator-type source is more versatile in that it allows one to use a flux of either 14-Mev or 3-Mev neutrons, depending on whether a tritium or a deuterium target is used. With a 14-Mev generator, one can obtain a flux of 10 9 neutrons/cm 2/sec, and with a 3-Mev generator, the flux is generally two orders of magnitude less. Although silver will become activated with either generator using proper moderation, detection may be

Jan 1, 1968

By JESSE L. MAURY

DEVELOPMENT of new gold mines in Canada since the price of that metal was increased in 1932 and 1933 has been of interest and importance to many of us. The day-by-day story has given an impression of aggressive effort and enough good luck so that the spirit of enterprise has been encouraged. It is the purpose of this article to report the results of a statistical appraisal which give emphatic numerical confirmation to this impression, together with certain side lights on the costs of development and equipment of new mines. The data presented have been taken from all readily available published sources up to the close of 1938 and are representative of that year. A. B. Bower did a large part .of the spadework and Weston Thomas offered many helpful suggestions.

Jan 1, 1939

By J. B. Morrow

BITUMINOUS COAL production for 1937 up to Nov. 27, was 400,000,000 ions, an increase of 3.43 per cent over the comparative period in 1936. The in- crease in consumption, however, was not so great as the increase in production. Stocks of coal, mostly in the hands of consumers, on Nov. 1 were 57,000,000 tons, compared to 44,400,000 tons at the same periods in 1936. The prospects were that both production and consumption for December, 1937, would be lower than for the corresponding month of 1936. , Anthracite production for the period ending Nov. 20 was 43,900,000 tons, com- pared to 48,500,000 tons for the corresponding period in 1936, or a decrease of 9.5 per cent. Production of mechanically loaded coal in. 1936 was approximately 57,000,000 tons, an increase of 17.5 per cent over

Jan 1, 1938

By J. W. Spretnak, G. W. Powell, J. H. Bucher

Tlze room-temperature tensile fracture oj smooth, round specitnens of three ultrnhigh- strength steels tempered to a wide range of strength levels was studied by means by light and electron-microscopic examination of the fracture surfaces. The fracture of AISI 4340 and 300 M at all the strength levels studied, and H-11, except after tempering at 1200° and 1300°F, occurs in three stages. The initiation of fracture is internal (except in some lightly tcmpeved specimers in which fracture is initiated at surface flaws), and is nucleated largely by separation at metal-second phase intevjaces. TIze voids grow and, coalesce to form a crack. When the crack has reached a sufficienl size, rapid propngutio~z ensues. Failure in this stage of fracture usually occurs by dimpled rupture of inicroshear stefis. In the case of H-11 tempered in the 1125° to 1300°F range, fracture in the shear steps is predominantly by concentrated deformation without void formation. The termination of fracture is usually occomplished by the formation of a shear lib in which fracture occurs by shear dimpled rupture. In the case of H-11 tempered at 1200° and 1300°F, no shear lip was obserued, and the radial elelments extend to the surface—a true termination slage does not exist. ThE tensile fracture of several metals and alloys has been investigated.2-4 In the case of polycrystal-line materials, cup-cone fracture usually results. The mechanism of cup-cone fracture may be summarized as follows.5 Cavities are formed in the necked region of the specimen. They usually are initiated by inclusions or second-phase particles. The cavities extend outwards by means of internal necking, and a crack lying about perpendicular to the length of the specimen is formed in the necked region. Subsequent crack growth occurs by the spread of bands of concentrated plastic deformation inclined at an angle of 30 to 40 deg to the tensile axis. Cavities are formed in the bands of concentrated deformation. The deformation bands zigzag across the bar with the net result that mac-roscopically the crack extends about perpendicular to the specimen axis. The final separation, or cone formation, appears to occur by continued crack propagation along one of the deformation bands out to the surface of the specimen. The micromechanics of the tensile fracture of ultrahigh-strength steels have not been thoroughly investigated. Larson and carr6,7 studied the tensile-fracture surfaces of AISI 4340 with a low-power microscope and reported that three stages of fracture could be observed in general. A centrally located region characterized by circumferential ridges, an annular region characterized by radial surface striations, and a peripheral shear lip were found. It was first pointed out by 1rwin8 that the central region is very probably one of fracture initiation and slow growth, and that the annular, radially striated region is one of rapid crack growth. Presumably the crack grows slowly, assuming roughly a lenticular shape, until it is large enough for the initiation of rapid propagation. In this investigation, it was attempted to determine the fine-scale aspects of the room-temperature tensile fracture of some ultrahigh-strength steels, and to relate the variation in fracture mode with microstructure. The steels studied were AISI 4340, 300M, and H-11 tempered to a wide range of strength levels. I) EXPERIMENTAL PROCEDURE The compositions of the steels studied are given in Table I. The steel was received in the form of hot-rolled bar stock 5/8 to 1 in. in diameter from which oversized specimens were machined and heat-treated. The heat treatments employed are given in Table 11. Subsequent to heat treatment, the specimens were ground to the final dimensions and stress-relieved by heating for 1 hr at 350°F (with the exception of the as-quenched steel). Standard smooth round specimens of 0.252-in. diameter and 1-in. gage length were tested in a Tinius Olsen Universal Testing Machine using a cross-head speed of 0.025 in. per min. The relatively coarse aspects of the fracture topography were determined by light-microscopic examination of sections through the fracture surface of nickel-plated specimens. A direct carbon-replication technique9 was used in the electron-microscopic study of the fracture surfaces. The replicas were examined in the electron microscope, and stereo pairs of electron micrographs were taken. The stereo pairs were then examined using a Wild ST4 Mirror Stereoscope. Carbide and inclusion particles extracted in the replicas were analyzed by selected-area electron diffraction. II) EXPERIMENTAL RESULTS The mechanical testing data are summarized in Table 111. The values reported are the average of

Jan 1, 1965

By W. T. Ober

the hammering effect acts only to a point 3 in. back from the cutting edge, and the hardening heat extends back only 1 in. from the cutting edge. Then, as a steel is taken from the fire, the grain condition is as shown in Fig. I. After the forging operation has been performed the condition shown by Fig. 2 exists. The heating operation to harden the cutting edge produces the effect shown in Fig. 3. The questions that naturally arise are: Will the cost of the extra heat treatment necessary to change this condition (annealing) be more than the saving that may be effected in the drill steel or will the extra heating be an economical as well as a wise thing to do? Is this condition necessarily detrimental to the maximum service of the drill steel? Can this annealing action be obtained in the hardening heat by heating more of the bit, say at least 5 in., to the hardening temperature but quenching only the end of the bit by a shallow immersion? Short Rock-drill Steels Reclaimed by Welding By W. T. Ober, Lynn, Mass. Experimental tests by the Thompson Company have shown that short lengths of rock-drill steels may be reclaimed by electric butt welding. The drills used in the experiments were hollow drills l1/4-in. in diametcr containing 0.95 per cent. to 1.05 per cent. carbon. The ends to be joined must first be ground off fairly square and the greater part of the rust, scale, etc. removed for 3 or 4 in. back in order to insure good electrical contact with the dies of the welder and countersunk, with an 80° countersink, approximately 1/4 in. The steels are then clamped in the copper dies of the welder, so that a length projects from the inside edge of each pair of dies equivalent to from one-half to three-quarters the diameter of the drill. The drills should also be brought into accurate alignment. The first step is to bring the ends into close proximity and then close the primary circuit of the transformer, slowly bringing the steels together until their ends lightly touch, when they will "flash," that is, minute

Jan 1, 1922