Search Documents

By Frank Robertson Van Horn

In June, 1911, the writer spent a few days in studying the economic geology of the vicinity of Park City. During this rather hurried visit a number of specimens of ore were collected, which have since been examind. The results of these investigations show that bournonite (PbCu-SbSa) is present in the ores in greater or less quantity. This fact has never before been reported, as far as can be learned. The failure to recognize this mineral is due to its similarity to tetrahedrite, with which it has probably been confused during a long period of years. Jamesonite (Pb2sb2s6) has been reported from the region in a rather doubtful manner, but the writer has seen it in notable amounts from several mines, and can offer the first analysis of this mineral from the district. Calamine (HzZn2SiO5) was found at one mine and has never been ecognized and reported from the district. Geogbaphy and Geology Park City, Utah, is located at an elevation of about 7,000 ft. above sea level on the eastern slope of the Wasatch mountains. It is situated approximately 25 miles southeast of Salt Lake City. ' The geology and ore deposits have been described in detail by Bout well and Woolsey.' The mines visited are situated south-southeast from the town. The Silver King Coalition mine is located in Woodside gulch about 1 mile southeast of Park City, at an altitude of about 8,100 ft. The other mines visited were the Daly West and Quincy, which are in Empire canyon about 2 miles sontheast of the town, at elevations of 8,300 to 8,500 ft. respectively. The Daly Judge tunnel goes into the mountain from Empire canyon about 1 mile south of the city, at an altitude of 7,700ft.

Jan 1, 1915

Discussion of the paper of DWIGHT T. FARNHAM, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 93, September, 1914, pp. 2357 to 2364. DAVID T. DAY, Washington, D. C.-Do you know anything about the character of that clay as to organic matter? H. RIES, Ithaca, N. Y.-No; it is a dark brownish clay, sandy in its nature. The brownish coloring is probably due to organic matter. Some lignite is also present. DONALD W. Ross.*-I have worked at the plant under consideration. I have not seen Mr. Farnham's paper; but in answering the question as to the organic matter, I might say there is practically no organic material scattered through the shale. There are, however, several layers of carbonaceous shale and rather low-grade coal interbedded with the formation. There are two very serious drawbacks-one which threatens to shut down the plant and another which merely means the expenditure of money. The first is taking care of the sediment from the washing away of the overburden. The government is doing extensive work at different points about Lake Washington with a view to creating a fresh-water harbor for Seattle. I understand that they keep at the Denny-Renton people to keep the channel of Cedar River clear. The Denny-Renton Co. can hardly help filling up the channel so long as they continue their hydraulic work, so this is probably one of their most serious problems. The other is this: There is a large percentage of what I should call micaceous shale or sandstone-a sandstone which contains a large amount of light-colored mica. Of course only a limited amount of this can be used in the manufacture of paving brick. As they shoot down the bank after the overburden of gravel and loam is washed away, these large boulders of micaceous sandstone come down. The strata have apparently been crushed where the clay pit is located so that the exact formation cannot be readily determined. These pieces of sandstone, 5 or 6 ft. in diameter, have to be blasted and removed from the shale. They bother both in the open pit and in the tunnel mining. In the tunnel mining of the shale blocks frequently cover the holes in the roof of the tunnel through which the shale is loaded into cars.

Jan 4, 1915

Map

Jan 1, 1958

Aalde, Kaare, (S'40) Box 827, Socorro, N. M. Aase, Glenn D., (S'40) Engr. Experiment Sta., Univ. of Utah, Salt Lake City, Utah. Abadesco, Enrique A., (S'39) Student. College of Engrg., Univ- of the Philippines, Manila, P. 1. Abbott, John L., (S'40) Met. Engr., Engr. Trainee. Wright Aeronantical Corp., Paterson, N. .J. Abbott, Robert H., (S'42). Agricultural & Mech. College of Texas, College Sta., Tex. Abreu, Ovidio M., (S'38) Dept. of Geol., Compauia Cousulidada de Petroleo, Caracas, Venezuela. Acomb, Allen, (S'41) 3921 Chestnut St., New Or¬ leans, La. Adam, Howard W., (S'41) Montana School of Mines, Butte, Mont. Adams, Charles E., (S'42) Uuiv. of California, Los Angeles, Calif. Adams, Charles W., (S'39) Student, Michigan Col¬ lege of Min. & Tech., Houghton, Mich. Adams, H. Travis, (S'39) 310 South 5th St., Bur¬ bank, Calif. Adams, John W., (S'42) Univ. of Texas, Austin, Tex. Adams, Rob L., (S'40) Lt., B. 0. C. No. 12, Fort Sill, Okla. Adamson, Charles R., (S'41) Uuiv. of Utah, Salt Lake City, Utah.

Jan 1, 1942

By G. H. Anderson

During an investigation of the copper-rich portion of the copper-silicon-iron system as part of an extensive research program on P.M.G. alloys, which was begun in 1937 in the research laboratory of the Phelps Dodge Corporation, it became apparent that the binary copper-silicon system below 7 per cent Si needed revision, therefore an investigation was undertaken. Both X-ray methods and microscopic technique were employed. Despite the many investigations that have the clarification of this system as their object, no two successive reports on the system have agreed in placement of the alpha-phase solubility limit, and uncertainty about the secondary phase first to appear has been voiced several times.3,4,5 It was therefore not surprising, when T. Isawa's6 and M. Okamoto's7 works were reported at the time we were finishing up our experimental work, to find essential disagreement between their results and ours. But when C. 5. Smith's latest work on the copper-silicon systema was published just as we were finishing our laboratory report, it was indeed gratifying to find that the latter's diagram and ours checked in all essential features, except the temperature of the peritectoid line above 830" C. Many attempts were made to retain the beta phase during the present investigation, but none was successful. Isawa,6 however, reports that he has been able to obtain X-ray photograms of the beta phase. The structure, he states, is body-centcrcd cubic with a lattiee constant of 2.848 ,&. at 7.2 per cent Si. Okamoto7 and Smith8 both use the designation Kappa for the hexagonal phase, and to avoid confusion this designation will he adhered to in the present paper. Preparation of Samples The alloys were melted in vacuum in a high-frequency furnace. from copper cathodes containing 99.98 per cent Cu, and specially refined silicon supplied by The Electro Metallurgical Co. This silicon is stated

Jan 1, 1940

By G. H. Anderson

During an investigation of the copper-rich portion of the copper-silicon-iron system as part of an extensive research program on P.M.G. alloys, which was begun in 1937 in the research laboratory of the Phelps Dodge Corporation, it became apparent that the binary copper-silicon system below 7 per cent Si needed revision, therefore an investigation was undertaken. Both X-ray methods and microscopic technique were employed. Despite the many investigations that have the clarification of this system as their object, no two successive reports on the system have agreed in placement of the alpha-phase solubility limit, and uncertainty about the secondary phase first to appear has been voiced several times.3,4,5 It was therefore not surprising, when T. Isawa's6 and M. Okamoto's7 works were reported at the time we were finishing up our experimental work, to find essential disagreement between their results and ours. But when C. 5. Smith's latest work on the copper-silicon systema was published just as we were finishing our laboratory report, it was indeed gratifying to find that the latter's diagram and ours checked in all essential features, except the temperature of the peritectoid line above 830" C. Many attempts were made to retain the beta phase during the present investigation, but none was successful. Isawa,6 however, reports that he has been able to obtain X-ray photograms of the beta phase. The structure, he states, is body-centcrcd cubic with a lattiee constant of 2.848 ,&. at 7.2 per cent Si. Okamoto7 and Smith8 both use the designation Kappa for the hexagonal phase, and to avoid confusion this designation will he adhered to in the present paper. Preparation of Samples The alloys were melted in vacuum in a high-frequency furnace. from copper cathodes containing 99.98 per cent Cu, and specially refined silicon supplied by The Electro Metallurgical Co. This silicon is stated

Jan 1, 1940

By James Hyslop

THE Pittsburgh seam in eastern Ohio has an average thickness of 5 ft and lies almost level Immediately above it is a layer of draw slate about 12 in thick, which normally has little structural strength, and is pulled down or allowed to fall as mining progresses Above the slate is a, variable thickness of roof coal, which in places will stand for the life of the working section and sometimes for the life of a secondary haulage entry The thickness of this roof coal varies from zero to 24 in In general, however, it does not provide a satisfactory roof, and usually is supported or pulled down About it is a mass of shale, soapstone and clay, of quite variable thickness, usually running from 5 to 8 ft and above this is a stratum of hard blue limestone, which provides a permanent roof Where entries are to be used for less than five years, the roof usually can be supported by wood or steel crossbars, but if they are to be used for a longer time, roof support is a serious problem All the roof material below the limestone disintegrates when exposed to air or moisture, and in a few years falls out between and over the crossbars Where this material is removed for a considerable height above the coal, the ribs scale and thus contribute to a further collapse of the roof As the height of the entry increases, cost of timbering is greatly increased, a problem that always is encountered where old entries are recovered or repaired METHODS During the last six years the Hanna Coal Co has used gunite for roof protection in mine entries Two general methods of guniting are practiced The first consists of the application of a I-in coating of unreinforced material This application does not provide any appreciable structural strength, and serves principally to protect the strata from exposure to air and moisture With the other method a coat at least 2 in thick is applied and provided with suitable reinforcing, which provides a structural strength proportional to the thickness of the coat and the reinforcing used The first method is adopted as a general practice, modified only where additional support is required "Gunite" is a mixture of cement, sand and water * The cement and sand are thoroughly mixed and screened before being fed into the hopper of a cement gun After the hopper lid is closed, compressed air is applied to force this dry mixture through the hose line to the nozzle, where the quantity of water needed to effect the proper hydration of the cement is added The coating is dense, and stronger than poured concrete

Jan 1, 1941

By A. Ghosh, T. B. King

The kinetics of the discharge reaction: 20'- (in silicate melt) = O,(g) + 4e- at a platinum anode in lithium silicate melts have been studied al 1350°C by galvanostatic methods. Plots of the sleady-state overpotential, q, as a function of the logarithm of the current density, i, showed injlections and were linear only at high current densities. The value of the overpotential was influenced by bubbling gas through the electrolyte. The ocer potential was also studied as a function of time. The rise and decay of overpotential were very slow processes. At low current densities transport is the likely rate-controlling process but at high current densities passivation of the electrode, Presumably by an oxide film on the surface, seems to be a contributory functor. IT is well-established that molten silicates behave as electrolytes'5 and, except in a few cases,6 conduction is entirely ionic. Moreover, it is supposed that a possible, and perhaps predominant, mechanism for phase boundary reactions between metals and slags is similar to that in corrosion whereby anodic and cathodic processes occur at unrelated sites, the metal serving to conduct electrons.1'8 Thus electrochemical studies of some slag-metal reactions would seem to be a useful way to diagnose the rate-controlling steps in the overall reaction. The electrochemical method is, in principle, a better diagnostic tool than the direct chemical method for the following reasons: 1) The partial electrochemical reactions, which are simpler than the overall reaction, may be studied individually. 2) The rate of reaction can be controlled at will and independently of the concentrations of reactants. 3) Fast reactions can be studied by relaxation methods.' Esin and his coworkers5'10"12 have pioneered such studies in silicates and have deviloped some ingenious techniques. Not all of their findings, however. can be accepted without a good deal of further work. In this investigation, the kinetics of the oxygen discharge reaction: 202- (in silicate melt) = Oz(g) + 4e- [I] at a platinum electrode were studied by both steady-state and transient galvanostatic techniques. Interest in this reaction was first developed as a result of the findings of Fulton and chipman13 that the reduction of silica, in a silicate slag, by carbon, dissolved in liquid iron, is a very slow reaction. Subsequent work, for example, by Rawling and ~lliott,'~ has demonstrated that the reaction under these conditions must be slow, because the rate is limited by diffusion of oxygen in the iron to the metal-crucible phase boundary at which a CO bubble may be nucleated. Further work by Tarassof,'~ in which the reduction of silica by aluminum dissolved in copper was studied, has shown that under these conditions, where carbon monoxide evolution is not involved, control of the reaction rate resides in diffusion of silica in the slag phase. However, there is no practical way of inducing sufficient convection in the system to make it clear that the phase boundary reaction is indeed fast. The overall reaction of silica reduction involves the discharge of silicon ions at cathodic sites and oxygen ions at anodic sites. In the examples cited, the discharged ions are dissolved in a liquid metal. In the present study of oxygen ion discharge, gaseous oxygen may be evolved at high current densities or oxygen may simply dissolve, possibly as oxygen molecules, in the silicate at very low current densities. The discharge of an oxygen ion at an anode must, in silicates less basic than the orthosilicate composition, be preceded by a reaction in the vicinity of the electrode, such as: which makes oxygen ions available. Platinum was chosen as the working electrode since it is comparatively inert to oxygen and is, therefore, expected to come rapidly into equilibrium with the electrolyte and with gaseous oxygen. Minenko, Petrov, and Ivanova16 have measured the electromotive force at a platinum electrode in molten silicates as a function of the partial pressure of oxygen in the atmosphere, the concentration of oxide ions in the melt, and the temperature. They found platinum to behave as a reversible oxygen electrode. At two different oxygen pressures, Po2 (I) and Pq (11). the electromotive force is given by: where F is the Faraday constant, equal to 23,060 cal per v equivalent, indicating that the electrode reaction is as written in Eq. [I.]. Platinum has been similarly used in molten silicates by other inve~ti~ators. "'~~ In this investigation platinum was used only as an anode, since a current deposits other elements on its surface and changes its characteristics.

Jan 1, 1970

By L. F. Mondolfo

An aluminum-copper 4 pct Cu alloy aged at room temperature for times increasing up to 78,000 hr was annealed at 170°C and the hardness and electrolytic potential determined during retrogression and subsequent aging. It was found that there is a change of behavior with increasing time of aging at room temperature which indicates that, given sufficient time, retrogression disappears and the room-temperature aging tends to progress directly into the high-temperature aging. WHEN an age-hardenable alloy is aged at low temperature after proper quench, changes of properties and structure take place. If this material is then heated to a temperature higher than the previous one, but still well below the solution-treatment temperature, the properties and structure changes produced by the low-temperature aging disappear and the material apparently reverts to the as-quenched condition, ready to undergo aging from the start. This phenomenon is termed reversion or retrogression. First discovered by Cayler3l it has been extensively investigated, as shown by the number of publications listed in the bibliography. From all the information available the following facts emerge: 1) All aeg hardenable alloys can be retrogressed.9 13, 19) 24, 33, 41, 42, 44, 47, 53, 54, 61, 63, 64, 66, 73, 78 2) All the properties changes that take place during aging at low temperature can be retrogressed to a smaller or larger extent.4,5,7,12,19,32,49,50,57,58,60,67,75,76 67, 75, 76 3) Retrogression requires that the temperature be well above the preliminary aging temperature. If the difference between the two temperatures is small, Little or no retrogression takes place.7,20,32,33,41,49 57. 65 4) The larger the difference between the preliminary aging and the retrogression temperature, the faster and more complete is the retrogression.20, 33, 41, 48, 65, 67 5) Retrogression can be produced several times in the same alloy.23, 35,41,57,59 6) The amount of retrogression that can be obtained depends on the aging temperature. Alloys aged at the lower temperatures can be retrogressed the most. The higher the preliminary aging temperature the less retrogression can be produced.20,25,33,37,44,49,54,58 7) Appreciable retrogression after aging at elevated temperatures is possible only if the preliminary aging has lasted a short time. After a certain time of aging at high temerature retrogression does not take place any more,:5,6,9,10,11,21,40,58 8) During retrogression the Guinier-Preston zones redissolve and disappear. The other precipitate

Jan 1, 1960

By Arthur F. Taggart, A. W. Thomas, T.C. Fitt

It was noticed early by operators that high recoveries and flocculation of the sulphide minerals were closely correlated in agitation-froth flotation. Later, this readily visible flocculation was found almost invariably to be due to the binding together of the oiled sulphides by minute air bubbles, and is now known to be characteristic of pulps in which at least one of the mineral species is coated with an insoluble collecting oil. In 1930 it was reported1 that in differential flotation a correlation exists between Brownian movement of particles in the pulp and their nonfloatability, and that Brownian movement and dispersion are likewise correlated, whence it would appear to follow that dispersion of a mineral particle in a flotation pulp denotes a particle condition unfavorable to flotation. In 1934 it was postulated2 that Brownian movement, dispersion and nonfloatability all flow from the condition of the surface of the dispersed particles. It was also postulated at that time that the surfaces of dispersed particles are ionized, the ionized compound being a product of reaction between a component of the particle and a component of the pulp, of a mass solubility of the general order of a fraction of a milligram to I 5 to 20 mg. per liter. It was then further asserted, and has since been confirmed by Bankoff,3 that sulphides so conditioned with soluble collectors as to be floatable flocculate without the intervention of air bubbles as binding media. The present paper comprises an inquiry into the nature of the bound and counter ions in zinc sulphide dispersed by sodium arsenate. A part of its findings was mentioned in the 1934 paper above cited.= The tests show that: I. When powdered granular zinc sulphide is immersed in aqueous solutions of sodium arsenate, arsenate ion is abstracted from solution and anchored to the solid surface, while sulphate and lower sulphoxy ions are concurrently displaced therefrom in substantially stoichiometric quantities. 2. The ion counterbalancing the anchored arsenate ion is zinc. 3. Dispersion and Brownian movement of zinc sulphide are concurrently maxima at an arsenate-ion concentration lying between 0.01 and 0.001-molar sodium arsenate. 4. Any condition or reaction that tends. to remove the zinc arsenate coating from the zinc sulphide particles decreases dispersion and Brownian movement concurrently. Experimental Three samples of zinc sulphide were used. Lot I was C.P. zinc sulphide, washed well be~ond absence of chloride, as shown by test with silver ion. Lot 2 was prepared by precipitation from hydrochloric acid solution of arsenic-free zinc, and was washed as lot I. Lot 3 was prepared by heating a portion of lot 2 in absence of air at 1200° to r300°C. for one hour."

Jan 1, 1943

By Arthur F. Taggart, T. C. Fitt, A. W. Thomas

It was noticed early by operators that high recoveries and flocculation of the sulphide minerals were closely correlated in agitation-froth flotation. Later, this readily visible flocculation was found almost invariably to be due to the binding together of the oiled sulphides by minute air bubbles, and is now known to be characteristic of pulps in which at least one of the mineral species is coated with an insoluble collecting oil. In 1930 it was reported1 that in differential flotation a correlation exists between Brownian movement of particles in the pulp and their nonfloatability, and that Brownian movement and dispersion are likewise correlated, whence it would appear to follow that dispersion of a mineral particle in a flotation pulp denotes a particle condition unfavorable to flotation. In 1934 it was postulated2 that Brownian movement, dispersion and nonfloatability all flow from the condition of the surface of the dispersed particles. It was also postulated at that time that the surfaces of dispersed particles are ionized, the ionized compound being a product of reaction between a component of the particle and a component of the pulp, of a mass solubility of the general order of a fraction of a milligram to I 5 to 20 mg. per liter. It was then further asserted, and has since been confirmed by Bankoff,3 that sulphides so conditioned with soluble collectors as to be floatable flocculate without the intervention of air bubbles as binding media. The present paper comprises an inquiry into the nature of the bound and counter ions in zinc sulphide dispersed by sodium arsenate. A part of its findings was mentioned in the 1934 paper above cited.= The tests show that: I. When powdered granular zinc sulphide is immersed in aqueous solutions of sodium arsenate, arsenate ion is abstracted from solution and anchored to the solid surface, while sulphate and lower sulphoxy ions are concurrently displaced therefrom in substantially stoichiometric quantities. 2. The ion counterbalancing the anchored arsenate ion is zinc. 3. Dispersion and Brownian movement of zinc sulphide are concurrently maxima at an arsenate-ion concentration lying between 0.01 and 0.001-molar sodium arsenate. 4. Any condition or reaction that tends. to remove the zinc arsenate coating from the zinc sulphide particles decreases dispersion and Brownian movement concurrently. Experimental Three samples of zinc sulphide were used. Lot I was C.P. zinc sulphide, washed well be~ond absence of chloride, as shown by test with silver ion. Lot 2 was prepared by precipitation from hydrochloric acid solution of arsenic-free zinc, and was washed as lot I. Lot 3 was prepared by heating a portion of lot 2 in absence of air at 1200° to r300°C. for one hour."

Jan 1, 1943

By H. M. Day, C. H. Mathewson

THE constitution of the system silver-mercury has attracted the attention of many investigators during the last two decades, but since their results are for the most part in poor agreement, there is little need for a review of their individual contributions. It remained for the very careful thermal and microscopic investigation of Murphy' in 1931 to give the constitutional diagram in its present and unquestioned form, which is shown in Fig. 1. He devised methods for taking cooling curves on alloys under high pressures and for the microscopic observation of alloys which contained liquid mercury as a structural constituent at ordinary temperatures. The compositions of the intermediate phases were confirmed and supplemented through X-ray analyses by Preston2 and Stenbeck.3 According to Murphy, at 276° C. silver is able to dissolve 44 to 45 weight per cent of mercury, which may increase at lower temperatures to about 50 per cent. Preston concluded that the saturation boundary occurred at 46 ± 2 per cent at 100° C. From the values reported in the literature, these are the only ones that may be accepted as lying even in. the right region. PREPARATION OF ALLOYS The silver used in the present investigation was supplied by the United States Metals Refining Co. through the courtesy of the Committee on Industrial Uses of Silver and, since a complete spectrographic and chemical analysis was furnished, no attempt was made to purify it or to further establish the impurities present. The analyses reported by the company are shown in Table 1. Milligan4 has found that the magnesium content is probably less than 0.0005 per cent.

Jan 1, 1938

By M. Deighton, R. N. Parkins

The metals Cd, ,Wg-, Sn, TI, Zn, and Zr reach a peak hardness after a criticfir1 deformation by rolling- and then soften with fwther rolling-, thereby exhibiting wovk softening. Optical metallography on Cd, Mg, and Zn shows that work softening is accompanied by a change in grain size occurring during deformation. The creep of zinc from -1l° to +60°C at stresses in the range of 7.9 to 17.3 kg per sq mm is given by € = e0 -t- Bt + Kt +at6. The third and second rate constcints are related by the equation a = K~ K6 and their stress and temperature dependence can be represented by the equations K = A, . exp - (u, - Bu)/kT. A model based upon the stress activated glide of sub-boundaries is proposed which qualitatively accounts for the metallog-raphic observations. Expressions, which are in reasonable quantitative agreement with the ex-pe~inzental observations, are derived for the creep of zinc. THE term "work softening" has been used previously by Polakowski1 and by Cottrell and stokes2 to describe phenomena where further strain of a deformed material leads to a decrease in flow stress. In both cases, however, the conditions were changed for the second straining. Here, the term "work softening" is intended to refer to a decrease in flow stress after continued straining in the same direction at the same temperature: work softening is the antithesis of "work hardening". Work softening of zinc was reported by chadwick3 and in discussion of that paper Jenkins4 indicated that cadmium also work softens. More recently work softening has been reported5 in two magnesium alloys, -99.5 pct Mg. Chadwick found that the hardness, 0.2 pct Proof Stress and the UTS of electrolytic zinc all increased with progressive cold reductions up to 30 pct and then progressively decreased with further rolling. Gay and Kelly6 used a back-reflection X-ray technique to study the effect of cold rolling zinc and found that although deformations greater than 2 to 5 pct reduction in thickness produced some recrystallized grains, deformations greater than 40 pct caused com-plete spontaneous recrystallization. At deformations greater than 60 pct the material was found to consist solely of recrystallized grains, -20 pm diam, the size of which decreased with increasing reduction and was much less than the initial grain size of the annealed material (-300 pm diam). Similar results were also reported for cadmium, tin, and lead.6 Gay, Hirsch, and Kelly' suggest that these experiments indicate recrys-tallization takes place when the dislocation density exceeds a certain value. However, no measurements of MATERIALS AND EXPERIMENTAL PROCEDURE The purity of the metals used in this work is indicated by the following figures: Zn (99.99); Cd (99.94); Mg (99.95); T1 (99.99). The zirconium was iodide crys tal bar with a probable purity of about 98 pct. The metals were obtained in the form of 0.25 in. thick strip or 0.425 in. diam rod by various fabrication methods and then annealed to ensure complete re-crystallization. Hardness-deformation curves were obtained at room temperature by rolling 4 in. thick strip under conditions which left a surface adequate for diamond pyramid hardness tests immediately after rolling. The hardness was taken as the niean of five impressions made using a 5 kg load and the time elapsing between rolling and making the last impression never exceeded 5 min. The zinc specimens for creep testing were from 3 by 3 by 4 in. cast slabs which were rolled to 0.10 in. thickness starting at 350°C and finishing cold. The resulting strip was cut into pieces 1 in. wide and annealed in batches. With suitable choices of annealing temperature between 100" arid 400°C five different grain sizes varying from 4.54 x 10' to 3.03 x l05 grains per sq cm (530 to 20 um diam) were obtained. Creep tests were done in compression using a sub-press, based on a design after Ford,8 in which the strip is compressed between dies 0.100 in. wide under conditions of plane strain. Since there is no lateral spread of the material, the area of contact between the dies and strip remains constant throughout the test and the application of a constant load, using the load maintaining device of a hydraulic testing machine, resulted in a constant stress. Covering the dies with strips of P.T.F.E. reduced frictional effects to a minimum. The creep strain was obtained by measuring the travel of the crosshead of the testing machine to a sensitivity of 0.1 pct reduction in thickness. The complete subpress assembly was contained in a steel box and for tests above the ambient this was filled with liquid paraffin and heated electrically. Temperatures below the ambient were obtained with a cooling mixture of acetone and solid carbon dioxide in the box. The liquids were stirred and the temperature of the specimen, which was controlled to ±0.5"C dur-ing a test, was measured by a thermocouple placed near the dies. Compression testing of cylindrical specimens was also carried out in the subpress using hardened flat discs separated from the test material by P.T.F.E. sheets which obviated barrelling of the specimens. Various initial strain rates were supplied by the hydraulic testing machine, and the deformation was measured by a clock dial gage resting on the cross-

Jan 1, 1970

By Stephen Royce

[PAGE Ground Movement Adjacent to a Caving Block in the Climax Molybdenum Mine (TP 2000 by JOHN W. VANDERWILT, Min. Tech., May 1946. Discussion by STEPHEN ROYCE and the Studies of the Design of Shaped Explosive Charges and Their Effect in Breaking Concrete Blocks (TP 2157 by GEORGE B. CLARK, Min. Tech. May 1947. Discussion by PHILIP B. BUCKY, V. H. CLARK, E. D. GARDNER, M. H. HAWKINS, H. L. WALKER, and the author) 2 See TP 2377, Min. Tech., May 1948 for discussion of San Manuel ProsPect (TP 2255 by H. J. STEELE and G. R. RUBLY, Min. Tech., Sept. 1947. Discussion by L. KENNETH WILSON, ELDRED D. WILSON and the authors)] Ground Movement Adjacent to a Caving Block in the Climax Molybdenum Mine STEPHEN ROYCE•-It is interesting to note from B, Fig 2, how closely the subsidence limits approximate to the 60° angle of draw, which is so commonly found to rule in large scale rock subsidence. The tension cracks shown at B are commonly found in the initial stages of subsidence movement and spread like a halo about subsidence limits as movement extends. These tension cracks usually grow into escarpments later on. Apparently from the illustrations and description given, a system of vertical fractures is the predominating weakness in the wall rock at Climax, and therefore both tension cracks and escarpments are prevailingly vertical in attitude. The illustrations in Mr. Vanderwilt's article seem to conform to the general rule that yield by subsidence is heralded by tension cracks which foreshadow the appearance of the subsidence scarps which are both described in the paper and shown in Fig 2. The difference between the B side and the A side of Fig 2 is apparently caused mainly by the vertical fracturing which controls subsidence at Climax as compared to the relatively homogeneous rock formation at A upon which the original figure in Peele's Handbook was based. The draw at B is exactly 60°, while the draw at A is a little flatter. The influence of the vertical fractures explains the difference. The surprising feature is the relatively small deviation from the general 60° draw line, which is about the average of rock subsidence experience. The influence of local fracture systems, faults and bedding in controlling subsidence all the way from extremely low angles of draw to vertical is rather fully discussed in the Peele's Handbook article referred to. The more illustrations of subsidence there are published the better will be our knowledge. The general principles are pretty well established. The wide local differences reflect the effect of local conditions. This paper is a very valuable contribution to the subject, and for the benefit of the mining industry, it is to be hoped that there will be many more such clear and concise presentations. Particularly block caving is apt to be of greatly increasing importance in the future of a mining industry that must meet high labor costs. More examples of block caving from small scale to large scale operations like those at Climax will serve a vital need. JOHN W. VANDERWILT (author's reply)-I would like to thank Mr. Royce for his discussion; however, in his comments the meaning of subsidence, draw and tension cracks is not entirely clear. As used in my discussion of subsidence at Climax, subsidence refers to movements involving appreciable downward displacement. Tension cracks indicate only

Jan 1, 1947

Executive Committee. ROBERT H. RICHARDS, Chairman. ALBERT SAUVEUR, Vice-Chairman. TIMOTHY W. SPRAGUE. HENRY A. WENTWORTH. AUGUSTUS H. EUSTIS, Secretary, 131 State St., Boston, Mass. The twelfth meeting of the Boston Section was held at the Engineers' Club, 2 Commonwealth Ave., Boston, on Monday evening, May 5, 1913, fifteen members and three guests being present. The meeting was called to order by Vice-Chairman Albert Sauveur, who introduced the speaker of the evening, Utley Wedge, of Ardmore, Pa. Mr. Wedge read his paper on the chloridizing roasting of copper ores, which he illustrated with a stereopticon, and which will be published in full by the Institute. After Mr. Wedge had closed his paper, which was received with great interest by all the members, the following discussion took place: Professor Hofman said that iron was formerly thought to ho essential to the Henderson process, but that it is not absolutely essential. Mr.Wedge said that, as far as he. knew, the presence of some sulphates was an abso¬lute necessity, and that line ores can be worked satisfactorily, although lime has an effect on the subsequent leaching. He added that the low fuel consumption of the latest Wedge furnace is a result of direct application of the combustion gases to the ore. Ten per cent. of fuel was needed with the muffle furnace. By direct firing he has been able to reduce the fuel needed to from 2 to 4 per cent. In the latest types of furnaces the gases from the upper hearth are not used. There is doubtless some temperature at which the loss. from copper chloride volatilization becomes serious, but in practice on Rio Tinto ores troublesome losses are not experienced. The copper apparently does not become volatile at. the temperatures where we would expect that it would. There are doubtless ores in which there would be serious danger from losses from this source. The latest furnaces do not use the high temperatures that were needed in the former single-hearth Wedge furnaces.

Jan 7, 1913

By J. H. Jensen

Bromine is the intermediate member of the halogen family of elements between iodine, a solid: and chlorine, a gas. The name is derived from the Greek "bromos," meaning stench. Bromine is the only nonmetallic element that is liquid at room temperatures with a melting point of -7.2" C and a boiling point of 58.78" C. Reddish brown in color, it dissolves easily in water to yield a red solution. Bromine volatilizes at ordinary temperatures to a red vapor that is very irritating to the eyes, nose, and throat. Density of the liquid is 3.12 and gas weighs 7.59 gpl at standard conditions. As the element is highly active, it exists in nature only as bromide compounds. Bromine was discovered by Antoine Jerome Balard in seawater bitterns in 1826 and first prepared in quantity in 1860. Distribution Bromine is widely distributed in nature and compounds occur in solution in natural brines, in seawater, saline lakes, oil and gas well brines, and in evaporite chloride minerals. The concentration of bromine salts ranges from 60- 65 ppm in seawater to several thousand ppm in oil well brines and saline lakes. The distribution of bromine in marine evaporite minerals and in the solutions from which they crystallized was determined many years ago by H. E. Boeke (1 908). Theoretical aspects regarding the geochemistry of bromine have been published in numerous papers (Raup and Mite, 1969). Bromine occurs in solid solution in carnallite and sylvite associated in potash de- posits; in halite in salt beds; salt in oil shales; and in trona deposits. Its presence is useful as a guide in geochemical exploration. The analysis of small amounts of bromides in the presence of large amounts of chlorides is discussed by W. Schwerdtner (1963). Manganese, iron, and iodine may interfere with the determination. Other analytical methods are discussed at length in the literature (Stenger and Atchison, 1964). Sources and Reserves The sources and reserves of bromine, given in [Table 1], appear ample to meet present and foreseeable requirements in all producing countries. With the occurrence of bromine salts in sea-water and other brines, the potential for bromine production is worldwide. It has been estimated that 99% of all commercially recoverable bromine is in the ocean. However, actual subterranean brines having a higher bromine content than seawater will continue to be the preferred sources of bromine for the foreseeable future. Markets and Prices About 17% (1968) of bromine produced is used in its elemental form, with the balance consumed as bromides and bromates. The largest use for bromine is ethylene dibromide which, together with tetraethyl lead, are used as an antiknock additive in gasoline. Tetra-ethyl lead is the antiknock agent. Ethylene dibromide combines with the lead after combustion in the engine to form a volatile com- pound that escapes from the engine with the exhaust gases.

Jan 1, 1975

By G. Sachs, S. I. Liu

Introduction In a previous investigation on the effects of repeated strains of large magnitude on the aluminum alloy 24 ST, it was found that the reduction in ductility by straining in tension was partially restored by a subsequent compression.&apos; As illustrated by the dashed line in Fig I,$ the ductility (e~) retained after prestraining in tension by a certain amount (el) and measured in a subsequent tension test is represented by a straight line sloping down under 4s°. If a compression of the same magnitude as the first tension is inserted (€2 = — €1) between prestraining and final testing in tension, such a "balanced" tension-compression cycle yields a ductility considerably higher than that present after prestraining in tension only. The results of these tests can be correlated with those of an investigation on the effects of prestraining in compression.~ As also shown in Fig I, the ductility in subsequent tensile tests decreased with com- pression, at a rate considerably slower than that after prestraining in tension. The above discussed testing conditions can be considered as special cases of a general straining cycle, consisting of first, straining in tension by an amount el, subsequently straining in compression by an amount e2, and finally determining the retained &apos;ductility, e,, in a tensile test. Prestraining in tension is then represented by el > o and e2 = o. Prestraining in compression is given by e~ = o and e~ < o. Balanced cyclic straining is defined by the condition el > o and cz = — 61. In order to obtain further information on the effects of straining cycles consisting of tension and subsequent compression, further tests were made, varying both the tension strain, el, and the compression strain, e2, within extreme limits; el varied between 0.06 and 0.28 and e2 between — 0.008 and —0.h approximately. Apparently, such tests have not been previously performed. They revealed phenomena which have not been recognized to date, The results of the investigation are herewith reported, without attempting to correlate them with internal processes within the metal structure. However, in order to assist in an analysis of this type, the results have been represented in various manners. In addition, further test data on the effects of prestraining by compression were provided by using specimens of various contours (notched specimens) in the sub-

Jan 1, 1949

By Walter Kauzmann

ALL viscous or plastic flow of incompressible matter is the result of shear strain; the changing shape of any body that is being plastically deformed can be completely described in terms of the shear strain occurring at each point in the body.[t] Furthermore, the relative amounts of shear strain occurring in different parts of a body under stress depend upon the relative rates of shear strain at those different points, so that if the dependence of the shear rate of any material on the temperature, shear stress, previous history, etc., were understood, the principles of plastic deformation would be known, and we could calculate how a body made of a given material, having a given shape, and subject to a specified system of forces, would change its shape with time. It may be said, then, that the problem of plasticity resolves itself into, first, the problem of the rates of pure shear processes, and second, the application of what is known about pure shear to actual cases. It is the purpose of this work to investigate the former problem -i.e., the dependence of shear rates on temperature, stress, etc.-from the standpoint of recent developments in the field of chemical-rate theory and with particular reference to the phenomena occurring in the creep of metals and in the plastic flow of crystalline solids in general. It is left for the mechanical engineer, and perhaps the expert in hydrodynamics, to deal with the problem of applications1 RESOLUTION OF MACROSCOPIC SHEAR INTO MICROSCOPIC MOVEMENTS; RESEMBLANCE TO CHEMICAL REACTIONS Just as any large body is made up of many small units, or atoms, so macroscopically observable shear is the result of many microscopic unit shear processes; just as the understanding of the behavior of large bodies demands the understanding of the atoms of which it is made, so the understanding of macroscopic shear demands the understanding of these fundamental unit processes. The study of shear from this "atomistic" point of view has made considerable progress. There has been fairly complete understanding of shear processes in gases for a long time, at least for nonturbulent flow, as a chapter on gaseous viscosity in any text on the kinetic theory of gases will prove. In recent years Andrade2 and Eyring3 have presented important theories for the flow of liquids and amorphous solids. Becker,4 Orowan,5 Taylor,6 Burgers,7 and Kanter8 have considered the

Jan 1, 1941

THE CHALRYAN.--I think that we have set the stage for the balance of the sym- posium. Most of the emphasis has been placed on the immediate value of every- thing we can do and everything we can learn for the furtherance of the war effort. I believe that ought to be first, but I also believe that this is the time for us to con- sider very seriously not only what these improved methods and techniques do to form a closer approach to ideal segregation but what effect these great quantities of scrap metals and alloys that are going to be produced this year and next, are going to have-what their impact will be-on post- war industry in general and in particular ,, on the primary metals fields. In some cases we have been hearing in the last month or two of the law of diminishing returns coming to the fore. We find alloy simplification growing and certain alloys being produced in great quantities, which will perhaps drop out of the picture some- what as the war ends but never to the lower ( stage they had before. We have I think a pretty good cross- section of the producers, the refiners, the reclaimers and ingot makers, the ultimate users here, and there ought to be some good and helpful discussion. The papers are open for discussion. Mr. Beattie, do you want to make any 1 comment? H. J. BEATTIE.*-To start the discussion I might ask Mr. Deitz what they do with manganese bronze turnings? We segregate the manganese bronze turnings from the other bronze turnings. The value of it seems to be much out of line with the price of ingot, that is, as compared to some of the other alloys like 88-10-2 or 85-5-5-5. I assume it is because they can only use a

Jan 1, 1943

Executive Committee. ROBERT H. RICHARDS, Chairman. ALBERT SAUVEUR, Vice-Chairman. TIMOTHY W. SPRAGUE. HENRY A. WENTWORTH. AUGUSTUS H. EUSTIS, Secretary, 131 State St.., Boston, Mass. The twelfth meeting of the Boston Section was held at the Engineers&apos; Club, 2 Commonwealth Ave., Boston, on Monday evening, May 5, 1913, fifteen members and three guests being present.. The meeting Was called to order by Vice-Chairman Albert Sauveur, Who introduced the speaker of the evening, Utley Wedge, of Ardmore. Pa. Mr. Wedge read a, paper on the chloridizing roasting of copper ores, Which lie illustrated With a stereopticon, and Which will be published in full by the Institute. After Mr. Wedge had closed his paper, Which was received with great interest by all the members. the following discussion took place: Professor Hofman said that iron was formerly thought to bo essential to the Henderson process, but that it is not absolutely essential. Mr. Wedge said that., as far as he knew, the presence of some sulphates Was an absolute necessity, and that lime ores can be worked satisfactorily, although lime has an effect on the subsequent leaching. He added that the low fuel consumption of the latest Wedge furnace is a result of direct application of the combustion gases to the ore. Ten per cent. of fuel Was needed with the muffle furnace. By direct firing lie has been able to reduce the fuel needed to from 2 to 4 per cent. In the latest types of furnaces the uses from the upper hearth are not used. There is doubtless some tem-perature at Which the loss from copper chloride volatilization becomes serious, but in practice on Rio Tinto ores troublesome losses are not experienced.. The copper apparently does not become volatile at the temperatures where we would expect that it would. There are doubtless ores in which there would be serious danger from losses from this source. The latest furnaces do not use the high temperatures that Were needed in the former single-hearth Wedge furnaces.

Jan 7, 1913