Search Documents

By R. W. Hertzberg, F. D. Lemkey, J. A. Ford

The technique of unidirectional solidification has been applied to the A1-AI3Ni and A1-CuAl2 ezltectic alloy systems; the controlled microstructure of A1-A3Ni consists of parallel A13Ni whiskers emhedded in an aluminum matrix while the Al-CuAl2, system solidifies as parallel alternate lamellae of aluminm and CuAl2. Mechanical tests (tension and flexure) have shown that the particle-matrix interface bond formed during unidirectional solidification allowes for efficient load transfer from the matrix to the reinforcing phase. Strength and fracture characterstics of the alloys were studied as a function of phase orientation; the tensile strength of controlled Al-Al3Ni samples was 43,000 psi (three times greater than that of as-cast specime~s). The strength of the Al-CIA2, cutectic was studied as a function of lamellae-flexure stress-axis orientation using a microbend apparatus. A twofold increase in outer fiber stress was observed as the lamellae were rotated from a position of no reinforcing (perpendicular to the stress axis) to one of maximum reinforcing (parallel to the stress axis), The brittle reinforcing constituent in each alloy (A13Ni and CuAl2) was observed to he the nucleating phase for fracture. It is to be concluded from this investigation that unidirectionally solidified eutectic alloys have a potential use as reinforcing coniposite) materials. In a recent review article, Chadwick1 has described the work of many investigators in the area of controlled solidification of binary eutectic alloys. Thus far, more than twenty eutectic alloys have been unidirectionally solidified to produce structures consisting of two phases in the form of alternating lamellae or as whiskers embedded within a continuous matrix; in either case, the phases are aligned parallel to the growth direction. In particular, Kraft and Albright2 have shown that the Al-CuA1, eutectic alloy exhibits a lamellar microstruc- ture as a result of unidirectional solidification while Lemkey, Hertzberg, and Ford3 have studied the A13Ni whisker-aluminum matrix morphology in the A1-A13Ni system. Whether these alloys could exhibit reinforcing behavior would have to depend upon the strength and volume fraction of the reinforcing phase (AI3Ni and CuA12) and the nature of the bond between the reinforcing phase and the matrix. Hertzberg and Kraft4 have shown that the interface bond between chromium whiskers and a copper matrix in unidirectionally solidified Cu-Cr is particularly good while Lemkey and Kraft5 have reported chromium-whisker tensile strengths in excess of 1,000,000 psi. However, with the chromium volume fraction being less than 2 pct, no reinforcing behavior was displayed by the Cu-Cr alloy.6 In view of the encouraging results concerning the good interfacial bond and high strength of the reinforcing phase in the Cu-Cr system and preliminary mechanical test data reported by Lemkey et al.3 for the A1-A13Ni system, the A1-CuA1, and A1-A13Ni eutectic alloys containing 50 and 10 vol pct, respectively, of the reinforcing phase give promise of possessing mechanical reinforcing behavior. Based on this premise, the objective of the investigation was to study the strength and fracture behavior exhibited by these anisotropic microstructures. EXPERIMENTAL PROCEDURE Controlled Solidification Procedure. An extensive description of the technique of unidirectional solidification has been presented elsewhere.' However, the pertinent details for each eutectic system studied are discussed below. Al-A13Ni System. Several master heats of this alloy were prepared by vacuum-induction melting in an A12O3crucible and casting in SiO2 mold or by induction melting in alumina crucibles under argon. The initial heats were prepared from 99.99 pct A1 and 99.99+ pct Ni, while later heats used 99.999+ pct A1 and 99.99+ pct Ni. Specimens of these master heats were unidirectionally solidified using induction and resistance heating sources and argon atmospheres at growth rates from 1.1 to 28.7 cm per hr. The thermal gradients in the liquid were controlled in the range of 26" to 36°C per cm for these runs. Al-CuA12 System. The master heat and controlled

Jan 1, 1965

By AIME AIME

APROXIMATELY one third of the world's iron ore is mined in the United States; and about 80 per cent of this third is mined in the Lake Superior ore region, and about 60 per cent in Minnesota. The Lake Superior iron ore region covers a vast area in the vicinity of Lake Superior that contained in early geological times large areas of iron-bearing sediments, which today form metamorphosed iron-bearing rocks, such as jasper, chert, taconite, and slates. Concentration of the iron content chiefly through solution and resultant removal of silica produced the ore bodies we find today in rock folds as on the Menominee range, at dike or impervious wall intersections such as on the Gogebic range, and blanket-type enriched ore bodies ly¬ing on or within the ore formation, such as occur on the Mesabi and in steeply pitching ore lenses elsewhere. In many places, folding and subsequent erosion of the tops of the folded areas has resulted in steep dips in the ore formation and contained ore bodies. The upper eroded edges are mostly buried under glacial over-burden. The slightly dipping Mesabi formation is the principal exception as to steeply dipping ore bodies.

Jan 1, 1941

COLUMBIA SECTION STANLY A. EASTON, Chairman, FREDERIC KEFFER, Vice-Chairman, L. K. ARMSTRONG, Secretary-Treasurer, P. 0. Drawer 2154, Spokane, Wash. D. C. LIVINGSTON FRANK A. Ross The first meeting of the Columbia Section was held on March 24, as a part of the 1916 Northwest Mining Convention which was held under the -auspices of the Spokane Mining Men's Club assisted by the Spokane Chamber of Commerce, the technical program being in charge of the Spokane Engineering and Technical Association assisted by the local sections of the A. I. E. E., A. S. C. E., and A. I. M. E. The program of the successive sessions was carefully arranged with view to its application to mining, and in addition to the technical program there were exhibits of ores, minerals, devices, etc., of interest to the delegates, who numbered over 500. A portion of the program was also arranged with special reference to the requirements of the prospector and miner. A reception, a banquet, a complimentary luncheon, a regular daily call' of the Stock Exchange, a visit to the High Schools and to one of the substations of the Washington Water Power Company and to the Union Iron Works kept the visitors entertained, the ladies being looked after by a special committee of ladies who held open house during the entire week. Several important resolutions were passed by the Convention and one by the Columbia Section, A. 1. M. E. With Stanly A. Easton, chairman, presiding, the Columbia Section, American Institute of Mining Engineers, occupied the time between 2.00 and 5.30 p.m., March 24th, the Moorish room of the Spokane hotel being filled with members and their guests. "The Apex Law and the Mineral Surveyor" was a paper presented by F. W. Callaway and generally dis-cussed because of its local application in the Coeur d'Alenes, the conclusions being reached after expensive litigation between two of the large mining operators in that district.

Jan 6, 1916

By W. C. Williamson, J. L. Shugert

DUST control is receiving considerable attention today by most companies as is evidenced by the many articles, papers, and books written on the subject. ~~~t of the larger mining companies have given this subject close study and have established standardized methods of control. W. C. WILLIAMSON and J. L. SHUGERT, Members AIME, are Assistant Ventilation Engineers, Anaconda Copper Mining Co., Butte, Mont. San Francisco Meeting, February 1949. TP 2705 A. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Jan. 17, 1949. Permissible Limits: The question of permissible dust limits has been considered by medical commit-ties and various national conferences. Dr. Lanza, of the Metropolitan Life Insurance Company, Dr. Le-roy U. Gardner, of the Saranac Laboratory for the study of Tuberculosis, and Dr. Pancoast, of the University of Pennsylvania, have been members of these committees. A statement included in reports of some of these committees is as follows: Concentrations to which the dust must be induced in order to be safe have not been absolutely determined. There is evidence that a concentration of more than five million particles per cubic foot of a highly siliceous dust is dangerous. Therefore, it may be stated that it is desirable to avoid counts of more than five million particles of dust containing free silica to a high percent in working places. Table I gives the safe limits adopted by several state industrial codes. Table I. Safe Limits of Dust Concentration Limit Million Particles State Per Cu Ft Cal~fornia Silica (less rhdn 10 pct) 50 Silica (10 pct to 50 pcr) 10 Sllica (more than 50 pct) 5 New York Frcc silica less than 10 pet by weight of rock formation 100 Frec silica more than 10 Pct by weight of rock formation 10 Oregon Silica (over 40 pct) 5 Silica (20 to 40 pct) 10 Silica (10 to 20 pet) 20 Wisconsin 15 million particles, under 10 nicrons in longest dimension per cu ft of air, when the quartz content of the dust is 35 pct, variations in free silica content will make proportional inverse changer in this standard Close attention to dust concentrations has been given to mining operations, since these operations are frequently carried on at considerable distances

Jan 1, 1951

By J. L. Shugert, W. C. Williamson

DUST control is receiving considerable attention today by most companies as is evidenced by the many articles, papers, and books written on the subject. ~~~t of the larger mining companies have given this subject close study and have established standardized methods of control. W. C. WILLIAMSON and J. L. SHUGERT, Members AIME, are Assistant Ventilation Engineers, Anaconda Copper Mining Co., Butte, Mont. San Francisco Meeting, February 1949. TP 2705 A. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Jan. 17, 1949. Permissible Limits: The question of permissible dust limits has been considered by medical commit-ties and various national conferences. Dr. Lanza, of the Metropolitan Life Insurance Company, Dr. Le-roy U. Gardner, of the Saranac Laboratory for the study of Tuberculosis, and Dr. Pancoast, of the University of Pennsylvania, have been members of these committees. A statement included in reports of some of these committees is as follows: Concentrations to which the dust must be induced in order to be safe have not been absolutely determined. There is evidence that a concentration of more than five million particles per cubic foot of a highly siliceous dust is dangerous. Therefore, it may be stated that it is desirable to avoid counts of more than five million particles of dust containing free silica to a high percent in working places. Table I gives the safe limits adopted by several state industrial codes. Table I. Safe Limits of Dust Concentration Limit Million Particles State Per Cu Ft Cal~fornia Silica (less rhdn 10 pct) 50 Silica (10 pct to 50 pcr) 10 Sllica (more than 50 pct) 5 New York Frcc silica less than 10 pet by weight of rock formation 100 Frec silica more than 10 Pct by weight of rock formation 10 Oregon Silica (over 40 pct) 5 Silica (20 to 40 pct) 10 Silica (10 to 20 pet) 20 Wisconsin 15 million particles, under 10 nicrons in longest dimension per cu ft of air, when the quartz content of the dust is 35 pct, variations in free silica content will make proportional inverse changer in this standard Close attention to dust concentrations has been given to mining operations, since these operations are frequently carried on at considerable distances

Jan 1, 1951

By H. B. Pulsifer

THIS paper outlines a method for rapid production of flat, granular surfaces on many of the medium hard- alloys. Grinding wheels and fabrics on wheels are not used; the purpose is accomplished by rubbing on emery papers and on fine abrasives heaped on hand boards. The advantages of chromic acid in the solutions for etching nickel and copper alloys are explained. Steels may require an additional step in the mechanical smoothing owing to the lack of an ideal etchant. Chloric acid is a. rapid etchant for steel. Thirty-six photomicrographs illustrate the steps in smoothing and the clearness with which structures can be rapidly exposed. New structures in low-carbon steels are announced. After a little practice, many materials can be finished within two or three minutes. CUPRONICKELS In the previous papers on the metallography of copper and magnesium which the author has presented to this Institute there has been an attempt to demonstrate the advantages of minimizing the mechanical work of surfacing and depending more on chemical means; the present paper continues the research into a still wider field. It is obvious that the success of a chemical method for smoothing and etching depends almost entirely on the use of a suitable reagent. The etchant must remove the surface granulations and outline the structures. A very special type of reaction between reagent and metal must be displayed. Promiscuous corrosion or the intensification of the attack about local couples -formed by impurities or components must not be in evidence. There are several reagents that etch highly polished nickel and copper alloys very well. Acidified ferric chloride solutions, concentrated and dilute nitric acid solutions, and nitric and acetic acids in acetone have -been used to good advantage for the purpose. However, if they are expected to etch rather deeply-that is, smooth as well as characterize-the results may be far from satisfactory.

Jan 1, 1928

By Alexander Bowie

Of the following problems, some have been suggested by recent articles in technical journals, which have led me to believe that the mathematical discussion here submitted may be of use to mining engineers. Problem I. To Find the Grade or Angle of Inclination upon which the Power Required to Move a Loaded Car Down-hill Will Haul an Empty One Up-hill. Let a be the desired angle of inclination; C, the coefficient of' friction; W and w, the weight in pounds of the loaded and of the empty car, respectively.

Jan 1, 1902

By Albert F. Hill

The manufacture of structural shapes in steel of uniform quality, which shall command the full confidence of the engineer, is a problem in practical metallurgy which is beginning to attract much attention in this country. The progress of the past fern years in the improvement of plant and processes has placed it within the power of the steel-maker to supply a material of such chemical composition as will meet the requirements; but this solves only in part the difficulties of the constractor. It is well understood that the influence of shop manipulations is a most decisive one upon the mechanical properties of the finished product; in many cases so great, in fact, as to cause an entire transformation in the character of the material, and to render it unfit for the service for which it was intended. On the other hand, mechanical treatment is frequently resorted to as an efficient corrective of certain undesirable properties, which may be due either to chemical composition or previous manipulation. This understood and accepted, it is evident that careful investigation of the effects of mechanical treatment is fully as necessary to the successful use of steel in engineering structures, as the investigation of the influence exerted by its chemical composition. All structural material has to undergo more or less mechanical treatment, such as shearing, punching, upsetting, etc. Each of these operations produces effects which are far more marked and decisive in steel than they are in iron, and means must therefore be adopted to counteract, or at least to modify, these effects before the material is permitted to enter the structure. The fact that both shearing and punching affect the tenacity and elasticity of steel has long been recognized; bat, through more recent investigations, it has been established that these effects are purely local, and are therefore susceptible of correction by other and simpler means than annealing. The importance of this discovery to the use of steel in structures is very great. The impracticability of

Jan 1, 1883

By G. W. Phelps

The field of industrial minerals is concerned with both sieve size and distribution of sub-sieve particles. A great deal of work has been reported on the techniques designed to provide information of this work. The term sub-sieve is here considered to include particular material that will pass a 325-mesh testing sieve. Plant men require rapid, precise and simple testing techniques that are, if possible, inexpensive with respect to equipment and manpower. A number of particle-size procedures have been developed, based on the Stokes equation for streamline movement of a particle of diam D, moving at velocity V through a liquid of viscosity n. 1 Particles are considered to be rigid, smooth spheres, completely dispersed at low concentration and moving at low velocity through the suspending medium with no slippage between particle and liquid. In particle size determinations the particle moves either from natural gravitational forces or those provided by centrifugal means. The diagram of Fig. 1 shows a spherical particle of density S and diam D moving downward at velocity L/T (or V) through a liquid of density So and viscosity n. The forces of gravity G (natural) or Gc (centrifugal) cause the particle to move through the liquid, thereby creating a viscous drag F or Fc. Within the streamline flow

Jan 1, 1967

By E. J. Rapperport, E. D. Levine

The boundaries of the (a +ß) field in the Al-Li system were determined between 150°and 550°C utilizing quantitative metallography and lattice-parameter measurements. The solubility of lithium in aluminum decreases from 12.0at. pct Li at 550°C to 5.5 at. pct Li at 150°C. P Al-Li is saturated with aluminum at 45.8 at. pct Li and has this boundary value constant over the temperature range 150°to 550°C. THE solid solubility of lithium in aluminum has been determined by several investigators, 1-6 but, as shown in Fig. 1, there is little agreement among the various determinations. The earliest investiga-tions'-' are suspect because of the use of impure materials. Although high-purity materials were employed in more recent work,4'5 the experimental techniques may have led to contamination of the specimens. Probably the best work has been that of Costas and Marshall,6 who obtained close agreement between results obtained by two independent phase-boundary techniques: electrical resistivity and mi-crohardness. No detailed studies of the solubility of aluminum in the bcc ß phase, Al-Li, have been reported. Cursory investigations1,2,6 have indicated only that the (a+ß) -p boundary lies between 40 and 50 at. pct Li and is relatively independent of temperature. The present work was undertaken in order to provide an independent check on Costas and Marshall's determination of the solubility of lithium in aluminum, to extend knowledge of this solubility limit to temperatures below 225°C, and to make an accurate determination of the solubility of aluminum in Al-Li. EXPEFUMENTAL Alloy Preparation. In view of the difficulties encountered in previous investigations of the A1-Li system, close attention was paid to the use of methods of alloy preparation and treatment that would minimize contamination. Aluminum sheet (99.99 + pct Al) was vacuum-induction melted in a beryllia crucible to remove hydrogen. Lithium (99.9 pct Li) was charged with pre-melted aluminum into a beryllia crucible, in a helium-filled drybox. The crucible was sealed in a Vycor tube and transferred from the drybox to an induction furnace. Melting of alloys was performed by induction heating in a helium atmosphere. Solidification was accomplished by means of a suction apparatus, shown in Fig. 2, in which the alloy was forced by changes of pressure into a 3/16-in. inside diam closed-end beryllia tube. This technique produced rapid solidification of a small portion of the melt, resulting in alloys with a high degree of homogeneity. Typical lithium distributions are presented in Table I. Transverse sections 1/8 in. long were cut from the alloy rods, and each section was split in half longitudinally. One half of each section was analyzed for lithium, and the opposing halves were employed for phase-boundary determinations. Lithium contents were determined by flame photometry with an accuracy of 1 pct of the amount of lithium present. Thermal Treatments. Homogenization and equilibration heat treatments were performed in electrical-resistance furnaces with temperatures controlled to ± 2OC. Calibrated chromel-alumel thermocouples were employed to measure temperature. Homogenization was performed in helium-filled l?yrex tubes for 1 hr at 565°C. The encapsulated specimens were then transferred directly to furnaces maintained at lower temperatures for equilibration. Equilibration times were 2 hr at 550°C, 8 hr at 450°C, 27 hr at 350°c, 90 hr at 250°c, and 285 hr at 150"~. These times were chosen on the basis of conditions employed by previous investigators. Alloys were quenched from the equilibration temperatures by breaking the capsules into a silicone oil bath. By performing all possible operations either in sealed capsules or in a helium-filled drybox, the specimens were given minimum exposure to the atmosphere. Quantitative Metallography. Metallography of Al-Li alloys is difficult because of the atmospheric reactivity of the ß phase. It was found possible, however, to prepare surfaces of good metallographic quality by preventing contact with moisture during preparation. Grinding through 4/0 paper was performed in the drybox. The specimens were then transferred under kerosene to the polishing wheel. Three polishing stages were employed: 25-p alundum with kerosene lubricant on billiard cloth, 1-µ diamond paste on Microcloth, and 1/4-p diamond paste on Microcloth. Between stages the samples were cleaned by rinsing in trichloroethylene and buffing

Jan 1, 1963

By Herbert Clark Hoover, Lou Henry Hoover

As stated in the preface, the nomenclature to be adopted for weights and measures has presented great difficulty. Agricola uses, throughout, the Roman and the Romanized Greek scales, but in many cases he uses these terms merely as lingual equivalents for the .German quantities of his day. Moreover the classic language sometimes failed him, whereupon he coined new Latin terms adapted from the Roman scale, and thus added further confusion. We can, perhaps, make the matter dearer by an illustration of a case in weights. The Roman centumpondium, composed of zoo librae, the old German ceniner of 100 pfundt, and the English hundredweight of 1112 pounds can be called lingual equivalents. The first weighs about 494,600 Troy grains, the second 721,900, and the third 784,000. While the divisions of the centumpondium and the centner are the same, the Libra is divided into 12 unciae and the pfundt into 16 unizen, and in most places a summation of the units given proves that the author had in mind the Roman ratios. However, on p. 509 he makes the direct statement that the centumpondium weighs 146 librae, which would be about the correct weight if the centumpondium referred to was a ceniner. If we take an example such as " each centumpondium of lead contains one uncia of silver", and reduce it according to purely lingual equivalents, we should find that it runs 24.3 Troy ounces per short ton, on the basis of Roman values, and 18.25 ounces per short ton, on the basis of old German. If we were to translate these into English lingual equivalents of one ounce per hundredweight, then the value would be 17.9 ounces per short ton. [ ]

Jan 1, 1950

By Jay F. Smith

The Alan Wood BOF Shop consists of two 140 ton furnaces with a rated yearly capacity of 1-1/4 million ingot tons, he hot metal for the BOF Shop is supplied by two 18 foot blast furnaces which produce an average of 2000 tons per day, To achieve the rated ingot ton capacity with this limited supply of hot metal, the preheating of scrap is necessary. This is accomplished in the furnace by using an oxygen-natural gas burner. Piping Arrangement The natural gas and oxygen are piped into the Shop through 8-inch lines to their respective valving stations. As can be seen from Figure 1, the flow of natural gas passes through a flow control valve which is common to both furnaces, after which it divides into two 6-inch lines forming two identical and independent gas control lines, one for each furnace.

Jan 1, 1972

By Dever Ashmead

ANTHRACITE was first mined in the Wyoming Valley and sold as an article of commerce in 1808. As some preparation has always been necessary to make it ready to burn, the preparation of anthracite must date back over a hundred years. Two vital factors have determined to a large extent the degree and method of anthracite preparation. These are, first, the character of the beds worked and the methods by which they were mined and, second, the equipment used and practices followed in the burning of the coal. It is not the intention here to go deeply into these phases of preparation as a paper of no mean length could be prepared on the history of either. Rather, the intention here is to point out the main considerations and to show the influence they have exerted on the preparation of anthracite. MINING METHODS AND THEIR RELATION TO PREPARATION In the beginning f the nineteenth century, the coal beds were virgin with the possible exception of some outcroppings that had been worked, to a slight extent, by the Indians. It is known that the American aborigines had a knowledge of the use of this fuel, because when the Wyoming Valley was purchased from them, in 1754, they mentioned the fact that, by selling the land, they would lose their coal.

Jan 9, 1921

By Kenneth S. Ritchie

THE discovery well of the world's -deepest oil producing structure, University 1-B of Group No. One Oil Corporation, in the Big Lake oil field, Reagan County, Texas, has had a remarkable record. The well is outstanding for the following reasons: (1) It is the world's pioneer well to produce. oil in commercial quantities from a structure 8500 ft. below the earth's . surface; (2) this well was the only. producer from the 8500-ft. pay for a period of 17 months and 24 days; (3) the flow of the discovery well has been free from-the customary changes at the casinghead, with the exception of putting on a back-pressure of 185 lb.; and, (4) the well's daily production of oil and gas increased rather steadily for 17 months and 18 days from an initial of 40 bbl. per day to a maximum of 2926 bbl. per day, and then six months later, after a period of decline and self-readjustment to subsurface changes caused by six more deep producers, the well set its real record for one day's production of oil at 2950 bbl

Jan 1, 1931

Executive Committee Board of Directors L F Reinartz, Chairman, H DeWitt Smith, Vice-Chairman, T B Counselman, M L Haider, Philip Kraft Finance Committee Board of Directors Andrew Fletcher, Chairman, A B Kinzel, D Wilson Endowment Fund "X" G F Moulton, Chairman, Erle V Daveler, '55, Philip Kraft, '56, I Brigden, '57 Honorary Memberships W M Peirce, Chairman, '56, M L Haider, ex officio, Andrew Fletcher, ex officio, John M Lovejoy, '55, D H McLaughlin, '57, Henry Krumb, '58, L F Reinartz, ex officio Investments Erle V Daveler, '57, Chairman, W M Peirce, '55, Henry Krumb, '56, G F Moulton, ex officio as Treasurer, Andrew Fletcher, ex officio as Chairman Finance Committee Local Section Appropriations A B Kinzel, Chairman, M L Haider, W S. Cumings, Fred J Meek

Jan 1, 1954

By Leo Ranney

ANY years ago a prospector came to a Nevada town and built himself a shack. Day after day he searched the hills for gold -but he found none. He closed his shack and hurried north, where a strike had been made. Next he tried to trap the flour gold that floats down the Snake River. He panned the black sands along the Oregon coast. He ranged over the mountains and up the gulches of far-off Alaska. At last, broken in health, six years ago he came back to his old home in Nevada. There his shack still stood-nobody wanted it. One day he started a garden in the rocky soil that he owned. His spade turned up a chunk of quartz, and in that quartz were stringers of gold. He had found a rich gold vein, running right under his own house. You gas producers who have hurried to Oklahoma, Louisiana, East Texas, South Texas, West Texas, even to California to drill wildcat holes a mile or two miles deep-why not, like the old gold prospector, have a look in your own back yard? Some of your coal seams contain 20,000,000 cu. ft. of natural gas per acre.

Jan 1, 1943

By Claude P. Heiner

While the title of this paper embraces the entire West Coast, the author, in the interest of simplification. has confined the discussion to California-particularly the central section. California's population has, risen 45 pct since 1940. Its electric requirements have also increased, not only because of the growth in industry and population but also because of the widespread tendency of all types of electric consumers to use more electricity than ever before. The growth of California's electric utilities is shown by published data covering operations, of three of its large systems and is given in Table 1.

Jan 1, 1949

By PHILIP N. MOORE

THE development of the power of the Tennessee River at Muscle Shoals has become a matter of political interest as well as engineering possibility. The controversy over it has been so active that the facts have been obscured, the possibilities exaggerated. Although the members of the American Institute of Mining & Metallurgical Engineers are not generally specialists in hydroelectric development, those who visited Muscle Shoals in October, following the Birmingham meeting of the Institute, were interested, and many of them surprised to learn the actual conditions. These have long been familiar to those who have studied the matter through the reports of the U. S. Engineers on the subject. The approved plan contemplates three dams-No. 1, a low dam close to the City of Florence, planned in the interests of navigation, since the construction of the other dams has rendered impossible the use of the river without it. No. 2-named the Wilson Dam is now under construction. Concerning it political argumentation has waged. No. 3 Dam-much smaller, is planned to be erected several miles above No. 2.

Jan 1, 1925

By J. L. Rodda, M. L. Fuller

In connection with an investigation in this laboratory on the high-zinc side of the copper-zinc system, it was observed that well developed segregate structures of the Widmansttten type were formed when a secondary phase precipitated from the solid solution of copper in zinc. This paper presents an analysis of the crystallographic relationship between the segregate and the solid solution matrix. The data to be presented are an interesting addition to the literature on segregate structures in that the plane of segregation is one of the less densely populated planes. In agreement with the generalization of C. H. Mathewson and D. W. Smith' the plane of segregation in the matrix contains the direction of closest atomic packing of the lattice. Furthermore, the matrix and the segregate are both hexagonal close-packed, which has not been reported hitherto in the 1iternture.l The increasing commercial importance of zinc alloys containing copper makes this fundamental study of value to the metallography of zinc alloys. Zinoeich Copper-zinc Alloys Copper enters into solid solution with zinc to at least 1.8 per cent at 400" C., according to W. M. Peirce.3 The solubility is less at lower temperatures. Thus a solid solution of copper in zinc, saturated at an elevated temperature, will precipitate the excess copper in a separate phase at a lower temperature, conditions of concentration, time, and temperature being suitable. The nature of these two phases has been established by the X-ray method of crystal analysis. Westgren and Phmgmén4 and also Owen and Preston5 have shown that the solid solution eta (7) is of the substitu-tional type with copper atoms replacing zinc atoms on the hexagonal

Jan 1, 1933

By N. J. Grant, E. Gregory

The creep rupture properties of wrought aluminum powder products made from five grades of sintered aluminum powder were investigated at temperatures from 400° to 900°F for rupture times up to 1000 hr. The effect of stress concentrations on materials of this type was investigated by means of notched creep rupture tests. A tentative correlation was obtained between the creep rupture properties and the structure as revealed by electron micrographs. SEVERAL papers have been published recently concerning the production and properties of wrought aluminum powder products and their possible high temperature applications. Most of the published work in this field has come from abroad, notably Switzerland, and articles by Irmann and his colleagues were summarized in English recently.'.' Most of the papers published by Dr. Irmann are principally concerned with the retention of properties (by a product which is produced from extremely fine flake powder and is subsequently hot extruded) after heating to high temperature for prolonged times. The powder may be in atomized or flake form, and during hot working the applied pressure is reported to plastically deform the aluminum powder, thus breaking the oxide skin and welding the particles together. Irmann attributes the remarkable properties to the dispersion of oxide inclusions. Specifically, the product described by Irmann is one labeled SAP (Sintered Aluminum Powder) in which the initial flake powder is so fine that at least 50 pct of the flakes have one dimension of 2 microns or less. The composition of the starting aluminum shows in percent, Fe, 0.18; Si, 0.19; Zn, 0.06; Ti, 0.03; Cu, Mn, Mg, all nil; balance Al, approximately 99.5 pct. Aluminum is not the only material that has been found to have increased resistance to deformation at elevated temperatures when produced by powder metallurgy. It has been reported by Middleton, Pf eil, and Rhodes- hat platinum has a higher recrys-tallization temperature when produced by powder metallurgy and exhibits peculiar properties, many of which are similar to those of the aluminum powder products. Difficulties were encountered in explaining the reason for the strengthening in the case of platinum since the existence of the oxide is doubtful. The authors attributed the special properties to "a small amount of suitably dispersed porosity." This theory was supported by von -~eer-leder4 in the discussion to the paper, and the similarity between this method of hardening and that suggested by Rohner in his theory of age hardening was pointed out. R. de Fleury5 attempted to explain some of the properties in terms of the modulus of elasticity and elastic limit of alumina and aluminum while von Zeerleder examined the relationship between the yield strength and the reciprocal of the powder particle size. Boenisch and WiderholtQ dealt mainly with the corrosion resistance of the powder aluminum material and compared it with other aluminum alloys. The diffusion rates of other metals in SAP and pure aluminum have been compared by Seith and Lop-mann.' They showed that the alloying metals diffuse particularly quickly in SAP possibly due to the very fine grain size. The properties of the Alcoa products were given by Lyle.' The creep rupture properties of SAP and two of the Alcoa experimental powder products were compared by Gregory and Grant hnd it was shown that these products are vastly stronger at 900°F than are the best cast and wrought alloys at 600°F. Since the publication of these data, the authors have investigated two further aluminum powder products and it is the object of this paper to show how the high temperature creep rupture properties of the five materials vary with oxide content and with the structure as revealed by electron microscopy. Materials One of the five products, SAP, a sintered aluminum product, was supplied by the Societe Anonyme pourl Industrie de l,Aluminium, Neuhausen a/RHF, Switzerland, through Dr. R. Irmann, while the others, M276, M257, M293, and M255 were supplied by the Aluminum Company of America as experimental powder metallurgical products. M255- and M293 were made from coarse and fine atomized powders, respectively. The other materials were made from flake powders with significant differences in oxide content, the details of the type of powders used in the manufacture of these materials

Jan 1, 1955