Search Documents

Jan 1, 1889

By D. G. Brubaker

IN the history of geophysical exploration by the electromagnetic method many procedures and types of equipment have been used. Source arrangements for surveying on the ground have included long wires grounded at both ends, large loops laid on the ground, small horizontal loops, and vertical loops of moderate to small sizes. Receivers have ranged from simple direction-finding coils to combinations of coils and a bridge circuit to measure quantities related to both amplitude and phase of the received signal. Primary considerations in choosing a survey method are effectiveness, speed, and economy. In work on the ground in which locating and out- lining conducting bodies is the objective, methods using a vertical coil and a simple direction-finder have been found the most satisfactory. Mason1 and his associates applied such a method by setting up a vertical source loop, fed with low frequency alternating current by an engine-generator set. With a direction-finding receiver they surveyed lines along the ground in the plane of the loop, taking measurements at each station of the azimuth and inclination of the magnetic field direction. Deviations of this direction from the normal direction, that is, from horizontal and perpendicular to the traverse line, indicated a conducting body. Recent advances in design of light-weight generating equipment have encouraged using this and similar methods.

Jan 7, 1957

Jan 1, 1947

Jan 1, 1947

By Michael D. Loy

While the coal industry in general has been slow in accepting automation, the last few years have seen a myriad of products developed by the private sector. These packages run the full gamut from sophisticated geological information systems to line entry discounted cash flow analyses. This paper is an attempt to unravel the confusion that may exist about mining software. Discussions will highlight major differences between software products (such as block vs. grid models, prefeasibility programs vs. Monte Carlo analyses), briefly discuss known vendors, list known package features and touch on hardware requirements. The paper also focuses on the costs of automation (both software and hardware), possible trade-offs, advantages to in-house systems (vs. timesharing), a recommended review/selection process (including suggested RFP format), a test case procedure, when to bring in a consultant, and staffing considerations.

Jan 1, 1983

By Charles Barron McIntosh

BECAUSE of the well known relationship between a low atmospheric pressure and increased amounts of methane in coal mines, attempts have been made to find associations between low pressures and coal mine explosions. An early study by F. Able disclaimed this relationship. He found that half the explosions took place during a rising barometer when methane content in a ventilated mine would be decreasing. A more recent study by C. L. Hosler revealed a close relationship between anthracite mine explosions and low atmospheric pressure. Bituminous coal mine explosions, where coal dust as well as methane can be exploded, were found to be more closely associated with a rising pressure following a low barometer than with the falling or low pressure period.

Jan 10, 1957

THE Howe Memorial Lecture, in memory of Henry Marion Howe, Past President of the Institute, was authorized in April, 1923, as an annual address to be delivered by invitation under the auspices of the Institute by an individual of recognized and outstanding attainment in the science and practice of iron and steel metallurgy or metallography, chosen by the Board of Directors upon recommendation of the Iron and Steel Division. The following were the Howe lectures and lecturers for the years indicated: 1924 What is Steel? By Albert Sauveur. 1925 Austenite and Austenitic Steels. By John A. Mathews. 1926 Twenty-five Years of Metallography. By William Campbell. 1927 Alloy Steels. By Bradley Stoughton. 1928 Significance of the Simple Steel Analysis. By Henry D. Hibbard. 1929 Studies of Hadfield's Manganese Steel with the High-power Microscope. By John Howe Hall. 1930 The Future of the American Ironand Steel Industry. By Zay Jeffries. 1931 On the Art of Metallography. By Francis F. Lucas. 1932 On the Rates of Reactions in Solid Steel. By Edgar C. Bain. 1933 Steelmaking, Processes. By . George B. Waterhouse.

Jan 1, 1946

By M. J. Scoble, N. Rowlands, L. Piciacchia

Pronounced non-linear behaviour of mine backfill arises from the influence of confining pressure, cementing agent content, curing time, void ratio and water content. Past research into backfill behaviour under stress is reviewed and related to the needs for constitutive laws which can be integrated into numerical modelling for mine design where structures employ backfill support. A method for representing non-linear backfill behaviour is proposed, which is based upon numerical regression treatment of triaxial laboratory data. The non-linear behaviour observed from a program of laboratory triaxial testing of cemented hydraulic backfill is presented. The particular influence of confining stress and curing duration is high- lighted. The paper concludes by considering the alternative means of accounting for such behaviour in mine design.

Jan 1, 1984

Now producing 35,000 tpd of coal from a deposit whose estimated reserves total 1.1 billion t, the Navajo mine of Utah International Inc. near Farmington, N. M., is the largest open-pit coal operation in the US. The history of this mine began in 1953 when, foreseeing the growing need for electrical power in the southwest, Utah International obtained a prospecting permit from the Navajo tribe. The lease, now covering 31,000 acres of the 12-million acre New Mexico-Utah-Arizona Navajo Indian reservation, was entered in 1957; in the next 3 years, Utah International negotiated with the State of New Mexico for water rights on the San Juan River, and finalized an agreement with the Arizona Public Service Co. to provide coal for the proposed Four Corners power-generating plant near Farmington.

Jan 10, 1974

Jan 1, 1946

[ ]

Jan 1, 1946

By R. Dawson Hall

THE stresses in the e simplest structures are often those we find most difficult to analyze. The most complex condition in mine stresses is found in simple tunnels where the roof, the sides, and the floor are a monolith. The functions of the parts are like the parts themselves not distinct and specialized, and the problems to be solved are like those in a metal structure with riveted joints or a redundancy of bars. This difficulty explains perhaps why the condition has not been treated. But just because it cannot be discussed in its entirety is no reason why it should be treated as an action of parts with specialized functions as a roof 'beans with supports and a foundation. The problem cannot be ignored on the ground that it is not of sufficient importance to warrant careful consideration, because conditions of complete monolithism, of which the tunnel is the type, are found materially unchanged) in room-and-pillar and in longwall work. This unity between roof, sides, and floor, which to the coal miner is a difficult conception, really deserves a scientific appellation, and perhaps holoid (from holos, whole, and eidos, form) will serve the purpose as well as any other. In a simple tunnel the roof, the sides, and the floor form integral parts of one and the same structure; and the distortion of one cannot be conceived without a consequent strain in the others. Thus when the roof of the tunnel droops by reason of its weight, the upper parts of the sides are drawn in because they are integrally-connected with the roof and must approach each other whenever, by the sagging of the roof, the distance between any two points in it is diminished. (See Fig. 1.)

Jan 9, 1915

Jan 1, 1951

Jan 1, 1951

Jan 1, 1936

Jan 1, 1949

By D. W. Jessup

ONLY during the past few years, have the old-fashioned methods for treating ores and byproducts progressed to any marked degree. The advent of multiple-hearth roasting, blast roasting, the baghouse, and the Cottrell plant indicate this change. It is the ability to roast and smelt sulfide ores and concentrates that gave this later advance. Further investigations that will solve the problem of efficient handling of flotation concentrates and their attendant ills are of the utmost importance. With future developments, the metallurgist will be able to smelt more economically and to treat still more refractory ores, making the early methods appear small by comparison. GROWTH OF SMELTING Well within the memory of pioneer smeltermen, the ore was charged directly into the blast furnace as it came from the mine;, only the richer, ores were smelted, the lower grade and sulfide ores were undesirable. Matte was, at first, thrown away and only two products) were desired-slag and lead bullion. Scores of the early smelting companies failed because of improper reduction of ores, high costs, short- furnace campaigns, inability to treat sulfide ores, and ores containing-zinc. With the failure of weaker companies, consolidation eliminated many others, until today the field is dominated by a comparatively few organizations, each strong financially. Formerly, a few thousand dollars would erect a small plant, whereas the modern smelter costs over a million dollars. Ore and products to which formerly no attention was paid are now treated with comparative ease and at a good profit. Mechanical improvements have modernized smelting, furnace tonnages show an increase, and metal recoveries have made enormous strides. Even though costs have decreased, they have not dropped in proportion to the improvements, because of the higher wages, greater costs of fluxes and coke, more undesirable ores smelted, etc.

Jan 8, 1925

Jan 1, 1931

By Raul Ramirez

Jan 1, 1983