Search Documents

By C. A. Wert

THE change in mechanical properties accompanying quench aging of carbon in a iron has been known for a number of years. Since the amount of carbon involved is rather small, however, no measurements could be made to correlate the property change with the state of precipitation of the carbide. Indeed, until a few years ago it was not plain which property might be used to indicate the state of the progress of precipitation. Some years ago the internal friction of solid solutions of carbon in a iron was demonstrated, and the use of this phenomenon to ascertain the amount of carbon in solid solution at any given time was developed. Shortly afterward the author made a number of measurements in which changes in electrical resistance, thermoelectric emf, and hardness were determined simultaneously with the internal friction (and hence with the precipitation) ? A little later Dijkstra and Wert measured the change in magnetic coercive force accompanying aging.' The present work was undertaken to inquire into the changes in yield strength accompanying aging. The work was done on specimens made of Puron. These specimens were 0.05 in. in diam and about 6 in. long. Though specimens of this small size are not ideal for yield strength measurements, such specimens are desirable for internal friction meas-

Jan 1, 1952

By Thomas M. Tharp

INTRODUCTION Attempts to analyze the stability of slopes, foundations and underground openings in discontinuously jointed rock have generally assumed full joint continuity or ignored the role of stress concentration at the tips of discontinuous joints. The most common approach in rock slopes is to consider a failure plane consisting of coplanar, but discontinuous joints separated by intact rock. The intact rock is assumed to fail in shear as a Mohr- Coulomb material and to contribute a strength component proportional to the fraction of the failure plane that is intact rock (Jennings, 1970). An alternative approach by Stimpson (1978) applies Lajtai's (1969) theory for shear strength of discontinuously jointed rock masses to slopes. Lajtai allows tensile failure in the intact rock of a composite surface. This theory yields lower shear strength than that of Jennings (1970) except in the presence of high normal compression, however it also fails to account for the stress concentration at the tip of a discontinuous joint. For a given slope geometry, stresses increase with slope height, but in both of these models rock mass strength is independent of size. A fracture mechanics analysis shows that particularly for small slopes, rock mass strength decreases with size. A continuous stepped failure surf ace produced by propagation of preexisting joints may develop at lower shear stress than predicted by the Jennings (1970) or Lajtai (1969) models. This fracture mechanics model applied to slopes in competent rock is more realistic in its assumed failure mechanism, and for large slopes more conservative than the Jennings (1970) or Lajtai models (1969).

Jan 1, 1984

By Eugene S. Perry

The most notable development in oil and gas operations in Montana during 1938 were extensions to the Kevin-Sunburst and Cut Bank fields. No new fields were discovered, although about 20 widely scattered wildcat wells were operated. Within or adjacent to proved fields about 100 wells were drilled, resulting in 81 oil wells and 14 gas wells. In general, production activities were below those of 1937, largely because of market conditions. Markets for crude were improved late in the year by construction of refinerirs at Pocatello, Idaho, Spokane, Washington and Cut Bank; and also by price concessions. However, demand was much

Jan 1, 1939

By Eugene S. Perry

The most notable development in oil and gas operations in Montana during 1938 were extensions to the Kevin-Sunburst and Cut Bank fields. No new fields were discovered, although about 20 widely scattered wildcat wells were operated. Within or adjacent to proved fields about 100 wells were drilled, resulting in 81 oil wells and 14 gas wells. In general, production activities were below those of 1937, largely because of market conditions. Markets for crude were improved late in the year by construction of refinerirs at Pocatello, Idaho, Spokane, Washington and Cut Bank; and also by price concessions. However, demand was much

Jan 1, 1939

By E. P. Pfleider, C. A. Dufresne

The problem of mooing open-pit ores over large vertical distances is increasing in importance because of the immense deposits being mined. Gravity fall of ore through transfer raises to central haulage points underground has advantages for certain open-pit operations, and this method is being seriously considered for the Carol Project now underway in Canada.

Jan 6, 1961

Jan 1, 1930

By D. M. Bondurant

Auger mining-extraction of coal with large diameter augers is proving profitable in recovering coal left after stripping has ceased to be economical. Its many advantages-low initial cost of equipment, low operating cost, low power demand, adaptability to selective mining, simplicity of operation, etc.-have excited the interest of some in the industry in its possibilities for underground operation.

Jan 5, 1951

New Products Equipment

Jan 12, 1950

By E. C. Winegartner, A. A. Ubbens

The company attempting to sell coal to large utility plants is faced with a confusing array of quality parameters and specifications which are often poorly understood by both the utility company and coal supplier. While these specifications are placed on the coal by the utility company, many of them originate with the boiler manufacturer who must guarantee that his product will perform satisfactorily on the design coal. A proper understanding of these parameters by both the coal supplier and utility company can lead to a better understanding of their mutual problem. This paper brings together most of the parameters in common use today and attempts to show what the parameters mean to the boiler designer, particularly in the area of boiler slagging and fouling.

Jan 1, 1977

By P. K. Guerrero, Nathaniel Arbiter

The correlation of power consumed by a tumbling mill with the dimensions, speed, and load has been attempted by three principal methods. One of these, the torque formula, has been reviewed critically elsewhere. This approach, while analytical, disregards the individual motion and speed of the tumbling bodies and assumes that the gross geometry of the entire load is sufficient to establish the power requirement. A more general approach, using dimensional analysis, has been applied in this laboratory by the present authors, and more recently by Rose. This disregards the internal conditions within the mill entirely and in effect is an empirical procedure for correlating data. Finally, the complete analysis of tumbling mill dynamics as first made by Davis attempts to develop the power requirement from individual ball and rod paths and velocities. Although Davis' result is applicable only at a single speed for a given size and load it could be useful, since his optimum speed is at the upper limits of conventional tumbling mill practice. Where power values predicted by the Davis equation were compared with actual mill requirements, they were found too low for small mills and much too high for the largest mills. This suggested that the agreement with actual intermediate range requirements might be fortuitous, and the development of the equation was examined critically.

Jan 5, 1960

[ ]

Jan 1, 1938

Jan 1, 1913

Organization Place Date 1917 American Society of Sanitary Engineers Grand Rapids, Mich. Aug. 1-3 National Association of Stationary Engineers... Evansville, Ind. Sept. 10-15 National Safety Council New York City. Sept. 10-15 National Exposition of Safety and Sanitation. New York City Sept. 10-15 American Iron, Steel & Electrical Engineers..:. Philadelphia, Pa. Sept. 10-14 American Institute of Metals Boston, Mass. Sept. 24-29 American Foundrymen's Association Boston, Mass. Sept. 24-29 Chemical Industries, Third National Exhibition. New York City Sept. 24-29

Jan 8, 1917

By Charles P. Williams

THE determinations of the specific gravities of a number of samples of lead produced in Missouri, which form the subject of this note, were undertaken with the view of ascertaining if any approximation to the purity of such leads could be reached in this manner. The results would seem to indicate that, whatever value the method may have in the case of the crude and more impure

Jan 1, 1877

By Charles P. Williams

The determinations of the specific gravities of a number of samples of lead produced in Missouri, which form the subject of this note, were undertaken with the view of ascertaining if any approximation to the purity of such leads could be reached in this manner. The results would seem to indicate that, whatever value the method may have in the case of the crude and more impure

AMERICAN INSTITUTE OF MINING ENGINEERS 29 West 39th Street, New .York, N. Y. PROPOSAL FOR MEMBERSHIP Address Member is hereby proposed by the undersigned, as a Associate Junior Member of the American Institute of Mining Engineers. Signatures of .-' three Members or Associates. Place of birth Year of birth Education, when, where and how acquired, with degrees, if any. " A technical education is not requisite for membership. Dates Please give record of experience on following page with dates; for example, in the form used by "Who's Who In America" and similar publications.

Jan 7, 1917

New York Holds monthly meetings, except June, July and August J E SPURR, Chairman A D BROKAW, Vice-chairman SIDNEY ROLLE, Vice-chairman M H MERRISS, Secretary-treasures, Nichols Copper Co, 25 Broad St, New York M F CHASE KARL HOFFMAN Boston Meets first Monday of each winter month C R HAYWARD, Chairman E C GEITHER, Vice-chairman D H McLAUGHLIN, Secretary-treasurer, Rotch Bldg, Harvard Univ Cambridge, Mass GEO H GILMAN GEO A PACKARD

Jan 1, 1923

By J. Wes Blakely

In the mid-1950s the importation of foreign oil began to encroach on traditional coal markets such as railroad steam engine fuel, home heating, electrical generating plants, and others. Many of the smaller coal companies with substantial coal reserves subsequently found that they could no longer continue to mine economically and merged in various ways with larger established coal mining concerns. As the seats of top management and authority were removed from the mines to large metro centers such as New York, Pittsburgh, and Chicago, the more personal relationship between mine workers and management that had existed prior to these mergers began to be eroded and replaced by 'remote control mine management. The disappearance of this face-to-face contact of upper management with mine employees tended to create barriers blocking simple effective communications between coal mine management and labor. In examining the human relations aspects of the coal mining industry, many elements, some concerned with work and others not, have depicted the industry as almost devoid of good applied human relations and communications practices, and, in truth, little has been done to alleviate this situation . In past years many coal producing companies, with the exception of one of the largest, failed to adequately define the term “communications” as it applied to their companies, whether internally or externally. Internally many still place heavy reliance on written communications such as company-wide newspapers to do the job of communicating with their employees which they feel ought to be done. One company puts an inordinate belief in its company "newspaper" as the primary instrument to stimulate its work force into increasing productivity. Primarily aimed at the workers, who greatly outnumber the salaried administrative people, this publication mainly documents the fortunes of individual mine workers who are felt to have achieved something with their lives, e.g., a mine worker who had managed to put four children through universities, the

Jan 1, 1981

Meeting of April 24, 1914.-President Thayer announced the appointment of the Committee on Safety and Sanitation. The Committee on Nominations for officers for 1915 was appointed, as follows: William J. Cox, Chairman; H. Poster Bain, Joseph Daniels, Charles E. Mills, R. V. Norris, E. Gybbon Spilsbury, and Herbert A. Wheeler. The request of twenty residents of Salt Lake City and vicinity for permission to establish the Utah-Nevada Local Section was granted and R. C. Gemmell was appointed Chairman of the Committee on Organization. The following resolution was adopted: Resolved: That under authority of Article V, Section 7, of the Constitution, a special Committee be and hereby is appointed, to consist of the President and six other members of the Institute, to be named by him, Who shall be authorized to appear before the proper authorities at Washington and urge that Mining Engineers be appointed upon the proposed Commission for revision of the Federal Mining Laws. Further Resolved: That the activities of this special Committee be restricted to the authority given in this resolution.

Jan 6, 1914