Search Documents

Jan 1, 1879

By R. E. Ogilvie, N. L. Peterson

Intevdiffusion and intrinsic diffusiorz coefficients were determined in the uranium-niobium system from diffusion couples analyzed with an electron microbeam probe. A Previously unveported intermediate phase, designated in this report as the delta phase, was found to exist along the mobium-rich side of the miscibility gap. Its composition width was determined from the concentration gradients in the diffusion couples. The presence of this phase was also confirmed by microhardness analysis and metallographic observations. THE excellent corrosion resistant properties, high-temperature strength and reasonable nuclear properties of niobium have prompted its use as an alloying element with uranium and as a possible cladding material for reactor fuel elements. Hence the formation and growth of intermetallic phases as well as diffusion data for the uranium-niobium system are of considerable practical importance to metallurgists and nuclear engineers. Diffusion zones may exhibit varying degrees of complexity dependi.ng upon the mutual solubility of the metals involved, and the intermediate phases which may form. In the simplest case where the metals exhibit a calmplete range of solid solubility, a single phase region is produced. Generally, however, the metals may react to produce a multiphase diffusion zone containing several layers of intermetallic phases. A number of investigatorsl-6 have analyzed the concentration gradients present in diffusion couples in order to investigate phase equilibria and solu- bility limits. If diffusion is the rate-controlling process in establishing a concentration gradient, the compositions at the interfaces of the intermediate phases will represent the equilibrium values expected from the phase diagram at the temperature at which diffusion has taken place. No published information is available at this time on diffusion in the uranium-niobium system. A number of investigators7-" have contributed information to the construction of the uranium-niobium phase diagram from other than diffusion techniques. There is good agreement on the high uranium side of the phase diagram, but the high niobium side of the miscibility gap still remains somewhat in doubt. The phase diagram as determined by B. A. Rogers, et al.7 is shown in Fig. 1. The present work was aimed at obtaining fundamental information about the solubility limits of the miscibility gap and diffusion in the uranium-niobium system. A Kirkendall effect, which might be expected on the basis of the rather large difference in melting points between uranium (1132°C) and niobium (2415" C), was also investigated. The concentration gradients were measured by an electron microbeam probe technique, similar to that used by Castaing,l2 Adda and philibert,13, l4 and Macres.4

Jan 1, 1961

Jan 1, 1927

Jan 1, 1885

Jan 1, 1937

Jan 1, 1890

By J. V. Emmons

THE processes of hardening and tempering steel tools within the past 15 or 20 years have been so developed that the forward strides of the industry can scarcely be followed by the average observer. No small part of the credit for this phenomenal advancement is due to the improved methods of measuring the high temperatures necessary. Pyrometry has made possible the discovery and use of the many special alloy steels the wonderful properties of which are revolutionizing the industrial world. So sensitive are these steels to changes of temperature that often a variation of only 10° F. at a critical point of the heat treatment will cause the failure of the tool. In the tool-manufacturing industry today, accurate control of the many heating operations is imperative. The principal processes in the manufacture of tools that require accurate high-temperature measurements are annealing, carburizing, hardening, tempering, and laboratory research. Several other operations, such as forging and straightening, use rougher and correspondingly less accurate methods. These operations are usually performed in the following approximate ranges of temperature: DEGREES F. DEGREES F. Annealing 1000 to 1700 Tempering 200 to 1200 Carburizing 1400 to 1000 Forging 1400 to 1800 Hardening 1400 to 2500 Straightening 300 to 1300 Laboratory research covers the entire range. Annealing and carburizing are usually done in muffle or semi-muffle furnaces, heated with coal, coke, oil, gas, or electricity. Many of them are of large size, holding several tons of steel at one charge. Both indicating and recording pyrometers are used. The recording instruments are generally of the thermoelectric type, while for the indicating, both optical and thermoelectric are used.

Jan 9, 1919

The suggestions of the members of the Institute are very much desired by the Committee on Nominations prior to deciding upon its nominations to fill the places of those officers who retire early in 1917. The Committee must make its final report to the Board of Directors early in October. The members are, therefore, asked to send in promptly their .suggestions for Directors as well as for Vice-Presidents and President. The Committee hopes to hear from a large number of the members. The officers to be elected at the annual meeting in February, 1917, are: One officer, known as Director and President. Two officers, known as Director and Vice-President

Jan 8, 1916

By C. E. Feltner

In a recent note, Meleka and Hiarris1 have reported that the application of a constant strain rate Ad a superimposed cyclic stress to 99.99 pct polycrystal-line zinc at room temperature produced some marked effects in the resultant behavior. In their work, one end of the specimen was pulled in tension at a constant strain rate while the other end was subjected to a sinusoidally varying load (20 cps) of constant amplitude. For the slower strain rates and the larger superimposed cyclic loads, it was observed that the specimen could withstand strains prior to failure more than 100 pct greater than the fracture strains obtainable in simple unidirectional straining. This ductility effect was interpreted as being due to a cyclic stress enhanced thermal recovery process. It is the purpose of the present note to describe some related effects in 99.99 pct polycrystalline cadmium. Specimens were loaded in repeated tension at room temperature with a stress of sufficient magnitude to cause failure in about 1000 cycles and the accumulated strain was measured as a function of cycles and time. In addition, some specimens were subjected to a steady creep stress equal in magnitude to the peak value of the cyclic tensile stress. The resultant strain-cycle and strain-time curves for both types of test are shown in Fig. 1. It should be noted that the static creep specimen failed in about one third the time required to produce a cyclic failure but in the cyclic test the specimen was able to withstand a uniform strain before necking more than 50 pct greater than that possible

Jan 1, 1963

By L. J. Lorig, B. H. G. Brady

The Discrete Element Method is a numerical technique suitable for use in modeling the discontinuum behavior of jointed rock. The disadvantage of this method, in its application to analysis of underground excavations, is the necessity to discretize the complete problem domain. Since the far-field rock responds to the excavation as an elastic continuum, it may be appropriately represented by the Boundary Element Method. This exploits the inherent advantage of the Boundary Element Method in representing a quasi-infinite domain in terms of its internal surface geometry and associated boundary conditions. The procedures employed in developing a first-generation coupled Discrete Element-Boundary Element algorithm are described and the solution to a simple problem verifying the performance of the coupled code is presented. A procedure for numerical treatment of installed support systems is also presented.

Jan 1, 1982

POSITIONS VACANT No. 255. A company manufacturing malleable iron fittings in Connecticut needs a manager for its steel department. Experience with converter is essential. No. 256. A prominent mining company in Central America wishes a shift boss for its mill and cyanide plant, who is technically trained, experienced, and can speak Spanish. He should he sufficiently expert to be able to take entire charge of the mill in case of emergency. Salary $150 per month on a two years' contract, with additional allowance for board, lodging and transportation expenses. No. 257. A Mexican copper mining company in the State of Puebla needs an engineer on surveying and mapping and drafting in connection with field construction. Healthy locality. Salary $150 per month.

Jan 1, 1918

By Irvin Mayes, Maher E. Tadros

The effects of particle properties and dispersion on the filtration behavior of magnesiumhydroxide, silica, and polystyrene suspensions in aqueous media were examined. It was found that effective separation of particles can be achieved using filter media with larger pore diameters than the size of the particles. The addition of electrolytes, at concentrations lower than the critical coagulation concentration, to suspensions of polystyrene or silica resulted in an increase of the cake resistance. This result was interpreted in terms of a decrease in the effective particle size due to the increase in ionic strength. For magnesium hydroxide, an increase in the absolute value of the surface charge was associated with an increase in cake resistance and a decrease in cake compressibility. Low cake resistance values were obtained with suspensions of large particles with low surface charge and blocky morphology.

Jan 1, 1980

By Calvin C. Brown, John Bigando

Pit slopes at Cananea commonly vary from 50-55°, and some have been standing for over 25 years. Their maximum vertical extent is 700 ft. Investigation of these slopes and the rocks of which they are composed has led to the decision to experiment with final pit slope angles of up to 70". Precision blasting to obtain a smooth final pit wall with minimum raveling is an integral part of this field experiment. Presplitting, one of the precision blasting techniques, requires the drilling of a single row of holes along the limit of a pre- designed excavation. The hole spacings and charge concentrations must be experimentally determined in the field, using published data as a base (Table 1). The holes are fired prior to the main round and carry no burden and therefore produce no broken rock. Thus, it is an operational cost with no direct return on investment.

Jan 9, 1972

By Louis B. Slichter

Prospecting is certainly the world's biggest and best gambling business. It is a game where the chips cost many thousands and where many millions, even billions, can be won. An attractive feature of this gamble is the fact that the players are free to rig the odds as favorably as possible. Only the limited bounty of nature, the restrictions of the laws of the land, the competition from other players, the limited sagacity of the player himself- only these, and other factors, restrict the possibilities for large winnings. Today probably about half the land surface of the earth remains to be searched for signs of ore visible at the surface. It is fortunate that so much land still remains for exploration by relatively economical methods. Looking to the future, it is a good guess that the costs of finding ore will increase in response to increasing technical difficulties. To continue to achieve profits from prospecting, it will become necessary to analyze the business more skillfully, in a more and more sophisticated manner. Whenever feasible, qualitative concepts must be replaced by their quantitative equivalents, improvements, and extensions.

Jan 6, 1960

By Merle L. Bowser, Lawrence W. Scott, John N. Murphy

The environmental status of underground mining operations is critical to the health and safety of the miners; particularly in a large mine, the multitude of interacting parameters that can favorably or adversely affect the environmental status makes the manpower requirement of the routine checking of specific areas and conditions a formidable one. While the concept of environmental monitoring for miners has been considered for some time, until recently the availability of sensors to reliably measure the parameters of interest severely limited the utility of such systems. The status of sensors for mine use and the evaluation of enviornmental monitoring systems is reviewed.

Jan 1, 1980

Jan 1, 1897

By A. Azis

The problem of expressing a nation's mineral resources in terms that convey a sense of economic reality poses a great challenge to those charged with keeping government policymakers informed. A model is presented that can be used to simulate and examine the effects of, for instance, differences in levels of output, transportation costs, mining costs or selling prices on the exploitability and expected order of development of new mineral deposits. The model in its present form can be used to screen, as a first cut, the economic from uneconomic deposits in cases where little or nothing is known about them in detail. To date, this has generally been done - reluctantly - by subjective judgments. This model provides an improvement on the "informed opinion" approach, as it forces those who use the model to be both systematic and explicit in their assumptions. Moreover, the procedure is repeat- able and each step can be defended and justified. Implications can be examined of the uncertainty associated with many of the variables. The model is entirely too general to be of use for actual feasibility studies. It is not useful, in the case of speculative or little-known deposits, to provide a model that has an input format more detailed than the information that is likely to be available. Should the user see a need for it, the model can easily be expanded to allow for the input of more detail or more variables.

Jan 1, 1977

By R. P. Olsen, A. K. Schellinger

Molten silicate salts, the important industrial byproducts termed "slags," are known to be electrolytic conductors at furnace temperatures. This property is due to their partial dissociation into ions with the ion kind and size being closely related to the slag composition. Ionic conductance, in liquids, is a function of the viscosity, which in turn is a function of the temperature. It could be anticipated, therefore, that a semi-log plot of conductivity vs. reciprocal absolute temperature might yield a straight line, in the case of molten silicates and salts. As liquids, the viscosity of these slags should follow the Shepard1 relationship: log viscosity = A/T + B Then, if the resistance of the molten slag is directly proportional to the viscosity: log Rs = A/T + B Resistance measurements of molten halide salts,2 and silicate salts34 by various investigators have, indeed, shown this straight line relationship between resistance and temperature. A further relationship between the conductivity versus the degree of ioni-zation, the size of the ions, and the slag composition is, also, to be expected. Large ions, and fewer ions, would move more slowly in a potential field and could not carry as much current as smaller, more numerous, and mobile, ions. Conductivity, therefore, would be smaller in the presence of such large ions and higher slag viscosities. The conductivity-composition relationship is of considerable interest in the case of the industrial slags produced in iron blast furnaces, and non-ferrous smelting furnaces. These slags usually approximate three component systems with several minor components as impurities. At least one of the major components is commonly purchased for the sole purpose of rendering the slag less viscous at a reasonable furnace temperature. Should the conductivity be related rather directly to the concentration of such a purchased slag component (that is, CaO) instrumental measurement and control at the furnace might be possible. Modern tele-metric control methods in aqueous chemical process industries are often based on the property of conductivity of solutions, and its variation with composition. Investigators3 of the phenomenon of electrical conductivity in molten blast furnace slags have established that these systems show lines of equal conductivity on their ternary diagrams at one temperature level. These isocon-ductivity lines form closed contours on the diagrams, and at times, minimum areas occur at which these contours are essentially closed down to a point. The conductivity reading at such a point, at one temperature , would, of course, locate one on the diagram, and give the slag composition. Research in this field is understandably scanty. The reactive nature of

Jan 1, 1950

By G. Hergert

SUMMARY Three gradients have been identified in regard to the average horizontal ground stress increase with depth. [S (0-900 m) = 9.86 MPa + 0.0371 MPa/m SHa (900-2200 m) = 33.41 MPa + 0.0111 MPa/m SHae (extreme)= 12.36 MPa + 0.0586 MPa/m] The extreme stress values are not caused by mining geometry and are of limited extent only. In some cases geological disturbances like faults and rock type boundaries suggest an explanation but in other cases the unusually high stresses cannot be explained readily. It is interesting to note that in the same locations the vertical stress components are very much higher than those derived from overburden weight and that the vertical stress gradient is similar to the gradient obtained from the extreme horizontal stress components. INTRODUCTION Ground stress determinations have been carried out in mines in Ontario and Manitoba, Canada, over more than a decade (Herget, 1980). Most of the sites are located in the Superior and Southern Tectonic Province of the Canadian Shield, which consist of Archaen and Proterozoic rocks comprising volcanics, metamorphosed sediments and granites. The youngest orogenic deformation occurred during the Grenville Orogeny (955 million years ago).

Jan 1, 1982

Jan 1, 1946