Search Documents

By Theodore Nagel

Fuel-oil, natural gas and coke oven gas, producing the higher temperatures of open-hearth current practice, have been gradually displacing producer gas the lowest cost fuel for open hearth operations. The lower temperatures of combusts on products from producer gas is caused by nitrogen dilution. Practical Application of Combustion Thermochemistry One pound of carbon burned to CO produces 3,960 B.T.U. and one pound of carbon burned to C02 produces 14,140 B.T.U. The second unit of oxygen uniting with gasified carbon (CO) produces (14,140 - 3,960) 10,180 B.T.U. which is (10,180 - 3,960) 6,220 B.T.U. more heat than produced by the first unit of oxygen forming CO by uniting with solid carbon. A review of the relative combustion heating values of commercial gaseous fuels reveals CO requires a minimum of air for combustion and because of minimum nitrogen dilution and the high thermal release from CO higher temperature combustion products are produced from CO than from natural gas or from coke-oven gas under similar combustion conditions. Inert nitrogen diluent lowers the calorific value of fuel gas and its diluting effect is cumulative in lowering the temperature of the products of total combustion. It is not only logical but practical in partial combustion, converting bituminous coal to gas, to generate the gas with reduced nitrogen dilution.

Jan 1, 1936

By Gilman C. Ritter

Moisture sampling of uranium ore should coincide as nearly as possible with weighing of the lot represented by the sample. This requires care by the sampler since the sample must usually be taken as a grab from each truckload as dumped. Correct proportions of coarse and fine material are necessary. A sample of at least 10 lb should be collected, placed in an air tight container, and promptly taken to the moisture determination room. Further, the sample should be dried for a minimum of 24 hr or until there is no further apparent loss of weight at a temperature no greater than 110°C.

Jan 10, 1958

By Robert P. Uhley, LeRoy Scharon

TEST gravity surveys were made in the Washington County barite district of Missouri on property owned by the Baroid Sales Division of the National Lead Co. This property is located just northeast of Richwoods in the northeastern corner of Washington County, Fig. 1. The area to which the surveys were confined comprised approximately 5000 acres, of which some 525 acres were surveyed gravitationally. Gravity observations were made at 2600 points within the area, observations being confined to relatively clear and gently sloping ground. Part of the area was heavily wooded, and the terrain too rugged for either the occurrence of a commercial barite deposit or a feasible gravity survey. The relief along the central drainage, Ditch Creek, was about 140 ft, the maxi- mum difference in elevation being 400 ft in a distance of 3 ½ miles.

Jan 1, 1954

By Rana P. Singh

Electrolytic metal reduction operatios in both aqueous and molten salt electrolytes are being studied by digital signal analysis. The purpose is to determine the relationship between the physical processes occurring in the cell and the frequency spectrum of the cell's fluctuating electrical parameters. The fast Fourier transform of cell voltage (in galvanostatic operations) or cell current (in potentiostatic operations) is computed on-line in real time for the electrorefining of zinc in aqueous acid chloride solutions.

Jan 1, 1984

By Theodore H. Eyde

In the southwest porphyry copper province, the virgin prospect with good copper mineralization cropping out has disappeared. Future discoveries will require an increasingly sophisticated arsenal of exploration techniques and concepts. One of the latter, stratigraphic analysis, is a technique which is often overlooked. A surprising number of exploration geologists still think of porphyry copper deposits as occurring wholly within intrusive bodies such as quartz monzonite or granodiorite. Disseminated copper mineralization, though genetically related to intrusive rocks, can occur within both the intrusive and the intruded rocks. At present, as much as 30% of the total copper produced from disseminated copper deposits in the Southwest originate from the intruded rocks rather than the intrusive.

Jan 4, 1972

By J. G. Davis, P. C. Thakur

Hazardous methane gas in coal mining is receiving increased attention due to the increased US demand for coal which has resulted in the exploitation of deeper seams and the utilization of more productive equipment. Problems posed by methane emission has the Mining Research Division of Continental Oil Co. (Conoco) accelerating efforts that began in the early 1950's with Consolidation Coal Co. (Consol).1 The program's focus is on finding new techniques for degasification of virgin areas as well as control of methane in gob areas.

Jan 10, 1977

By John L. Schroder, Woods G. Talman

EXPERIENCE has shown that certain known natural conditions and other indefinite characteristics combine to make a mining area vulnerable to mountain bumps. Some of the known conditions are heavy overburden, an overlying stratum of strong non-elastic rock, a structurally strong coal seam that does not crush easily and yet is the weakest stratum in the series, and a floor stratum of more than ordinary firmness. The indefinite characteristics could include resistance of top or bottom of a coal seam to lateral flow, effect of immediate top and bottom strata, nature of the coal seam, and other factors about which very little is known. It is in this area that exhaustive study is needed to achieve positive control of the dreaded mountain bump hazard.

Jan 8, 1958

G. F. COMSTOCK (author's reply to discussion *).-The discussion of this paper has been of such volume and interest as to constitute in itself a sufficient excuse for the paper, even though the paper itself may have been as much in error as some of its critics have maintained. Mr. Howard does not appear to realize some very practical facts that the opponents of his theory have advanced. Among these are: the coarsely crystalline fracture of the nucleus of a transverse fissure, so different from the smooth fatigue break around it; the occurrence of fissures in large numbers in certain heats or rollings of rails, while other heats or rollings do not develop them; and the much smaller proportion of transverse fissures found in rails rolled .from reheated blooms as compared with direct-rolled rails. These facts are not explained by Mr.

Jan 6, 1919

By H. R., Collins

THE purpose of pulverizing coal before burning it is to make available every heat unit it contains. Machinery has been developed which will pulverize coal in one operation, delivering it to bins in front of the furnaces at an expenditure of about 17 hp.-hr. per ton, in a medium-sized plant. The cost of the operation depends upon the amount of moisture that must be expelled before pulverizing, the cost of labor, and the cost of coal delivered at the plant. At a small plant, requiring a pulverizer with a capacity of only ½ ton per hour, the cost per ton pulverized will naturally be greater than at a plant requiring the largest pulverizer, with a capacity of 7 tons per hour. The first step is to reduce large lumps to a size suitable for drying uniformly, before passing to the pulverizing mills; this is done in rolls, at a single pass. The second -step is the elimination of moisture, in order to facilitate pulverizing to great fineness, while also increasing the heating effect and the temperature attainable when the coal is burned. There are other mechanical advantages in the handling of, dried coal. Driers are now manufactured which are able to eliminate moisture without distilling any of the volatile combustible matter in the coal; they are fired by hand or with pulverized fuel. The heat first surrounds the shell of the drier, being confined within a chamber where complete combustion takes place; the heated gases are then led through a duct to the discharge end of the drier and enter the inside of the shell at a temperature not exceeding 300° F. This temperature is maintained by the operator and is indicated by a pyrometer. Volatile combustible matter is not likely to be distilled until the temperature rises above 400° F. On discharging from the drier, the coal is usually passed over a magnetic separator in order to prevent pieces of iron from going to the pulverizer. Two types are used: a magnetic pulley which automatically discharges its collection of iron, and a lifting type, from which the iron is removed by hand when convenient.

Jan 4, 1918

By John F. Lundeberg

CLAUSS1 observed that if isothermal creep data could be approximated as straight lines on a log stress-log time plot, a relationship existed that could be expressed as log t = m log s + b [ l] where t = time,

Jan 1, 1965

By B. C. Craft

Oil and gas development in Arkansas during the year 1933 has been marked by considerable wildcat drilling, considering the overproduction prevalent in the oil industry. Arkansas showed an increase in drilling operations during 1933. There were 45 completions from 10 counties resulting in 7 oil wells and 38 dry holes, compared with 37 completions resulting in 4 oil wells and 33 dry holes during 1932. Miller County continued to be the most active area, with 18 completions resulting in 3 oil wells and 15 dry holes. Extensive exploration around the Miller County field has more definitely established the producing limits. It has confirmed the belief that produc-

Jan 1, 1934

By J. J. Kramer, W. A. Tiller, G. F. Bolling

The solidification of poly crystalline zone-refined lead has been examined. A novel casting technique was used, with several advantages such as unidirectional heat flow, atmosphere control, and decanting of the liquid during any stage of growth. The experimental results show the separate existence of two textures, a (111) surface texture at the chill surface and a texture in the columnar zone, in the absence of conditions which would produce dendritic growth. WALTON and chalmers have most recently shown that the dendrite direction is the preferred axial orientation for the solidification of many metals in casting. Experimentally, for aluminum and lead, they showed that in the columnar zone the dendrite direction, <l00>, predominated, developing from an equiaxed chill cast layer that exhibited no preferred orientation. A reasonable description of the way in which grains closer to the dendrite orientation were able to encompass other grains was then set forth. For their materials, it was also shown that high superheats could inhibit a preferred axial orientation from developing, presumably by inhibiting dendrite growth. The observations of Rosenberg and iller, on the other hand, showed that zone-refined lead, cast under conditions similar to those of Walton and halmers,&apos; had a definite <111> texture in the columnar zone. However, no examination was made of the chill surface to find out if the columnar zone texture was independent of the orientations at the surface. Since the existence of preferred growth in Upure" lead is thus in doubt, a reexamination of the casting of zone-refined lead is presented here, using a novel casting technique. EXPERIMENTAL PROCEDURES AND RESULTS Zone-refined lead was prepared from two starting materials;99.999+pct supplied by ASARCO, and 99.999pct supplied by COMINCO. The manner of zone-refining and the phenomenological tests for purity after refining, have been describedelsewhere.&apos; The casting apparatus is shown schematically in Fig. 1. The following general procedure was used: The metal was cut directly from the best parts of

Jan 1, 1963

FRIENDS of the late Charles F. Rand presented in 1930 a sum of money from which. the income is available to support various phases of the work of the Institute in which Mr. Rand was so deeply interested. At present the fund amounts to $10,000. The specific terms of the deed of gift are as follows: "The fund collected to establish a memorial to the late Charles F. Rand shall be placed in the custody of the Board of Directors of the American Institute of Mining and Metallurgical Engineers, to be set up as a trust to be known as the `Charles F. Rand Foundation&apos;, the income of which shall each year be applied to a distinct purpose to be decided upon in that year by vote of the Board of Directors. This purpose shall be such as to promote the general welfare of the Institute and to constitute a permanent memorial of the usefulness of Mr. Rand, who for many years gave unstintingly of his time and talents in its service.

Jan 1, 1952

By W. B. Hall, Joy D. Lewis

Mine-run ore is received at Vitro in gondola cars and fed directly to a Cedar Rapids impact crusher. Following screening, the undersize travels through a recently installed three-stage sampling plant where successive cuts are executed by conventional Geary-Jennings type cutters to produce a final sample of 1 lb per ton of raw ore fed. Crushed ore is transported to one of three storage silos or to stockpile, depending upon grade and type of amen- ability. This permits the blending of a mill feed with some degree of consistency. Final grinding is accomplished in one of two closed circuit ball mill-classifier systems allowing simultaneous processing of two basic types of ores. High acid consumers may be leached separately in the required environment. Part of the free acid remaining can then be utilized by an ore stream entering later whose component ores require much less free acid for leaching.

Jan 11, 1958

By D. E. Buchanan

The: volatility of a motor fuel is an index to its quality and to the satisfaction that will attend its use as an internal combustion engine fuel. Natural gasoline is concentrated volatility; threfore, it is quite natural that the most important market for natural gasoline should be for blending with less volatile refinery gasolines. Progress in the art of manufacturing natural gasoline, particularly in fractionation, which has made possible the elimination of the fixed gases and lighter hydrocarbons having a tendency to gasify at atmospheric pressure and temperature, has made it possible and desirable for refiners to utilize an ever-increasing percentage of natural gasoline in their finished product. This, in turn, has enabled the industry at large with each succeeding year to supply to the consuming public a better grade of gasoline. While cracking processes and improved fractionation in refinery operation have resulted in higher yields of gasoline per barrel of crude oil refined, natural gasoline has also played a large part in this respect because it has enabled the refiner to cut deeper into the crude and still maintain proper standards of volatility by blending natural gasoline with the product from his stills. There is, of course, with even the present improved grades of natural gasoline, a limit to the percentage that may properly be used. This percentage varies with different grades of crude oil, varies according to the facilities employed at the refinery and varies according to the grade of motor fuel manufactured; therefore it is not possible to say that for a certain predetermined amount of motor fuel to be manufactured in a given area, a certain definite amount of natural gasoline will be required. It is, however, generally conceded, and statistics bear out the statement, that the average gallon of motor fuel sold in this country contains approxi-matcly 11 per cent. of natural gasoline. Isolated cases may be found where in a very few refineries during certain seasons no natural gasoline is used, while in other plants as high as 35 per cent. and 40 per cent, natural gasoline is used in certain grades of motor fuels. Production Statistics The total production of natural gasoline for 1927, including California, is estimated at 1,627,600,000 gal. This represents an increase of 20 per

Jan 1, 1928

By Ed Ramsay

The Kerr Addison process involves the cyanidation, flotation, and roasting of graphitic gold ore. The grinding and treatment section of the present mill has at the present time a capacity of 1400 stpd and the precipitation section has a capacity of 6000 stpd. The grind is maintained at 80%, -200 mesh, and a gold recovery of 92% is obtained in the cyanidation circuit. With flotation and roasting, the overall gold recovery is increased to 98%.

Jan 1, 1978

By Frank Peterson

THE manufacture of gasoline by extraction or precipitation from the natural gases in which it is found, the present status of. the industry, its past development and future extensions; offer a subject which is so broad that to handle it in its entirety would require a voluminous paper. The writer will, therefore, attempt to concentrate the essential matter of the subject for a general presentation, giving some of the most interesting details of the factors that are important to the industry. This industry has drawn liberally on the principles of physics and chemistry, and, to a large extent, has had to adapt such information as is most useful-not from data recorded with reference to petroleum, but from data recorded with reference to general treatment of other materials. Because of the complex character of the petroleum series of hydro-carbons and the fact that data, such as solubilities, vapor pressures, etc., of the different petroleum compounds have not been determined, we are still working by rule of thumb in. some essential phases of the industry. Furthermore, the difficulties of determining such data are almost insurmountable. We have not one,, but two butanes to deal with-not one, but several, pentanes, hexanes, heptanes, and, as we ascend in the series the complexity and multiplication of isomers increases at such a rate as to make the task of isolating and studying their physical characteristics almost beyond the hope of possible attainment. The industry is the connecting link knitting the interests of oil producers and refiners into a much closer relationship than ever existed .prior to its inception and development. The relation between the producer and the refiner of petroleum prior to 1910 was. a rather antagonistic one in a commercial sense. It was to the interest of the producer of crude petroleum to sell it for a maximum consideration; the refiner&apos;s interest was to obtain the same product for a minimum consideration; therefore, each side of the business transaction retained within his own hands as far as possible the trade secrets of his business. Each side maintained an attitude of cold-blooded business sympathy only for the other. Cas-

Jan 12, 1917

PRESIDENT AND DIRECTOR JOHN M. LOVEJOY NEW YORK, N. Y. PAST PRESIDENTS AND DIRECTORS HOWARD N. EAVENSON PITTSBURGH, PA. HENRY A. BUEHLER ROLLA, Mo. VICE-PRESIDENT, TREASURER AND DIRECTOR KARL EILERS NEW YORK, N. Y. VICE-PRESIDENTS AND DIRECTORS LOUIS S. CATES NEW YORK, N. Y. PAUL D. MERICA NEW YORK, N. Y. WILFRED SYKES CHICAGO, ILL. R. C. ALLEN CLEVELAND; OHIO HENRY KRUMB NEW YORK, N. Y.

Jan 1, 1936

THE task of the smith who works in iron is very laborious, indeed far more so than that of the coppersmith just described. For he also handles heavy weights continually, and stands constantly erect be- fore the fire of the forge, since the hardness of the iron cannot be softened except by means of heating and boiling it well. In this place he continually moves his body, now thrusting the iron into the heart of the fire with large thick tongs, now removing it to look at it and to put sand, tuff, or other earth over it, now putting on fresh charcoal, now moistening and slowing down the fire, and now cleaning it. Finally, while the iron is hot

Jan 1, 1942

By J. Marin, H. A. B. Wiseman

This paper presents results of an experimental study dealing with the plastic stress-strain relations of aluminum alloy 14s-T6 subjected to combined biaxial tension and compression stresses. Plastic stress-strain relations for both constant and various types of variable stress ratios were determined and a comparison made with the simple flow theory of plasticity. THIS investigation was undertaken for two main purposes: 1—to obtain plastic stress-strain relations for Alcoa 14s-T6 when subjected to various combinations of biaxial stresses, and 2—to determine the validity of the flow theory in predicting plastic stress-strain relations for combined stresses. The biaxial stresses used were tension combined with compression. These stresses were produced by subjecting a thin-walled tube to axial tension and torsion. Various types of combined stress conditions were investigated. To provide control test data and information on the influence of biaxial stresses on the strength, the usual constant stress ratio type tests were made. These tests showed that the biaxial yield strength agrees approximately with the distortion energy theory. However, the Prager semi-empirical theory agrees best with the test results. For these constant stress ratio tests the plastic stress-strain relations were found to agree approximately with the flow theory. (For constant stress ratio the flow and deformation type theories are identical.) In view of the fact that the constant stress ratio tests cannot distinguish between the flow and deformation theories, a number of variable and special biaxial stress tests were made. These tests showed that the flow theory is inadequate, since large differences exist between the experimental and theoretical results. Special tests were also conducted to check the validity of the isotropic yielding assumption. This assumption is made in the linear-type flow theory. In these tests specimens were loaded in tension to predetermined values beyond the proportional limit stress. The tension load was removed from the specimen and the specimen was subsequently loaded in torsion to fracture. Other tests were applied with the order of torque and tension loading reversed. The nominal stress-strain curves for these two tests approximately coincide indicating that the assumption of isotropic yielding is valid. In addition, these tests verified the requirement by the slip theory of plasticity that prestraining below 140 pct of the proportioned limit stress in either torsion or tension did not influence the subsequent plastic stress-strain relations in tension or torsion. Another type of test was conducted to check the assumption that the axes of principal stress and strain coincide during plastic flow and variable stress conditions. These tests were conducted by applying combinations of axial tension, internal pressure, and torsional loads such that the axes of maximum principal stress could be rotated through 90" during the loading path. The results of those tests showed that the angle between the axes of principal stress and strain varied greatly and that the assumption of coincidence between axes of principal stress and strain is not valid. Introduction In various metal processes including forming of sheets, rolling of bars, and extrusion of rods, metals are subjected to stresses beyond the yield strength of the material. Often these stresses are not simple stresses acting in one direction, but are combined stresses acting in more than one direction. Structural and machine members are often subjected to combined stresses. To adequately determine the factors of safety for these members, it is necessary to know the plastic stress-strain relations of the material used for various combined stress conditions. Various theories have been proposed for predicting the plastic stress-strain relations for combined stress in terms of the simple tension plastic stress-strain relation for the material. To determine which theory might be adequate, test results must be obtained for various combined stress conditions, in order to compare the actual with the assumed theoretical behavior. Although there is considerable test data available for combined stress conditions in which the principal stress ratios are constant, relatively little test information is available for vari-

Jan 1, 1954