Search Documents

By Dwight K. Smith

A new pozzolanic composition has been developed for cementing oil wells where moderate to high temperatures prevail. This material is an entirely different concept to other oil well cementing materials, such as portland cements, cements containing additives, or liquid resins. Its characteristics are such that it is not, at present, recommended for use at temperatures less than 140º F. It can he either accelerated or retarded across a wide range of well conditions. This new cement is composed of a pozzolanic material, hydrated lime, and a chemical activator to give it early initial strength. This material can be used in wells from 6,000 to 18,000 or more feet where temperature conditions are similar to those along the Gulf Coast. This cement, when set, has no soluble portion subject to leaching or any compounds that should be attacked by sulfate waters or brines. For this reason, it should be permanent when placed adjacent to formations carrying any type of fluid. The compressive strengths in 24 hours are more than adequate for wells where temperatures are 140°F and higher. These values ore in excess of many other types of cementing composition presently in use in the field. This pozzolanic composition does not retrogress in strength at high temperatures as do some other types of cementing materials. The slurry weights of this material will vary slightly according to the specific gravity and water requirements of the pozzolnn itself. The materials covered herein will mix from 13.5 to 14.3 lb/gal, and will have a waiting-on-cement time comparable to other materials used under the same conditions. Economically speaking, this composition is less expensive than either portland cements or retarded cements presently being used under deep well conditions. INTRODUCTION Pozzolans are siliceous material which, though not cementitious in themselves, contain constituents which at ordinary temperatures will combine with lime in the presence of water to form compounds which have a low solubility and possess cementing properties. The use of pozzolanic materials dates back many hundreds of years and both the ancient Greeks and Romans were aware that certain volcanic deposits, if finely ground and mixed with lime and sand, yielded a mortar which possessed special properties. Generally, the early strengths of such materials were rather weak and were considered insufficient for modern commercial usages. Pozzolanic materials have been used extensively with portland cement in mass concrete to obtain special properties. In recent years, large quantities of certain pozzolanic materials have been used successfully admixed into portland cements for oil well cementing. Pozzolans, being reactive silicates, will combine with the free lime that is an inherent component of set portland cements and thereby. becomes cementitious themselves. POZZOLANS FOR OIL WELL CEMENTING There are many types of pozzolans, some of which are more reactive than others. The quality of the pozzoIan depends on the degree of reactivity, chemical composition, fineness, and other less well understood factors. Some of the more widely accepted pozzolans are those classified as fly ashes, while others are certain materials of volcanic origin. pozzolans which require large vol-

Jan 1, 1957

By E. S. Leaver

THE purpose of this paper is to describe, in a general way, gold-dredg-ing operations in California, with particular reference to unusual features, including types of deposits and recent attempts to improve the recovery of the gold. DREDGING AREAS The gold-bearing formations that traversed the western slope of the Sierra Nevadas for a north and south distance of some 300 miles furnished the immediate source of the gold found in most of the placer deposits of California.. Erosion through a long period carried the gold, together with various forms of partly disintegrated material, to lower elevations and formed placer deposits. Through the classifying action of water in motion, the coarser gold and heavier material of various kinds were deposited relatively near the source; consequently, in' the higher moun-tain country, old river channels were worked feverishly during the early California gold-rush days because of their high gold content. With the working out of these known high-grade channels, and from the knowledge thus obtained of prehistoric stream beds, drift mining was started and flourished until about 1890. Even today many drift mines are operating with the objective of opening other old Tertiary river channels that have been covered by volcanic flows.

Jan 1, 1937

By K. B. McQuillin

The increasing volume of data produced by the Anglo American Corporation of South Africa, Limited, during the course of coal exploration prompted the establishment of a computer based processing system for coal data. This system, known as the Coal Mine Evaluation System, consists of geological, mine planning and financial evaluation sub-systems. This paper describes the use of the geological sub-system in assessing the surface mine potential of a portion of the Witbank Coalfield, South Africa, in which more than one thousand core boreholes have been drilled to date.

Jan 1, 1977

By Edward Gridley

Members of the Institute who were present at the Amenia, N. Y., meeting, in October, 1877, will remember their visit to the hematite mines, just west of the village of Amenia, and some of them may perhaps recall the deposit of carbonate ore south of the opening made for the hematite. The smelting of this carbonate during the last few months, has produced an iron that seems worthy of being brought to your notice. A little more than a year ago, at the Wassaie Furnace, Dutchess County, N. Y., we made a few hundred tons of iron from a mixture of two-thirds ram carbonate and one-third Chateaugay ore, hoping that it would be suitable for steel purposes, but as the iron showed phosphorus 0.189 per cent., it, was not offered. This iron looked well and seemed quite strong, and gave good results in malleable castings; but no special tests of strength were made. About February 1st, of this year, we began using two-thirds roasted carbonate, and one-third Chateaugay, and noticing that the iron mas stronger than usual, we had two samples tested, which showed tensile strength of 32,014 and 34,176 pounds per square inch. After our stock of Chateaugay ore was exhausted, me put on one-third ram carbonate with the two-thirds of roasted carbonate, and the first test made of the iron, showed 40,008 pounds per square inch. The three tests given above were made by Mr. A. J. Copp and Mr. E. B. Manning, of the Phoenix Furnace, Millerton, N. Y., on a machine of Riehle Bros., Philadelphia. Since these tests were made, they have broken samples made with all carbonate ore as follows: 39,669, 40,816, 41,882, 42,281, 39,902, and 40,130 pounds per square inch. A test taken from the same bed of iron as the last-mentioned (40,130), was broken by Mr. A. Blass, at Irondale Furnace, showing 40,151 pounds per square inch. A sample broken on the Riehle Bros. machine, at Stevens Institute, under direction of Professor R. H. Thurston, showed 40,000 pounds per square inch. Another sample was broken by Professor Thurston on his torsion machine, and gave torsion 7", and tensile strength of 44,500 pounds. And

Jan 1, 1884

By H. W. Reid

One of the outstanding features of the year was a further marked decline in the footage drilled. This is estimated at 169,000 ft., as against 218,000 ft. for the previous year, and 372,500 ft. in 1930. Owing to repair work and improved production methods, there was an increase of about 4.25 per cent in the amount of oil won, the production being estimated at 10,160,000 bbl., or an increase of 400,000 bbl. over 1931 and nearly 750,000 bbl. more than in 1930. (See Table 1.) At the end of November there were 28 rigs in operation. During the first 11 months of the year 54 new wells were started; the average depth of those completed was 2476 feet. Owing to the continued restriction of drilling programs there has been little of outstanding interest in the way of new plant or technique. The use of the acid bottle, for testing the verticality of wells while drilling, has increased considerably, and this is now in use in practically every well except the very shallowest. During the last six months of the year fairly extensive use has been made of electrical coring. The number of wells started in the Colony up to the end of November, 1932, was 1894. The average number of producing wells during the year was 789, or 41.7 per cent of the total. Of these, 214 were flowing wells, 473 pumping, 80 bailing or swabbing, and 22 were produced by air or gas-lift. Although the last category represents less than 3 per cent of the total, there has been a marked increase in the use of air or gas-lift as compared with 1931. During the year there were 16 companies engaged in producing oil, as compared with 14 in the two previous years. In addition to one small refinery which started to operate at the beginning of the year, the five existing refineries worked continuously. At the latter very little has taken place in the way of extensions, except at one in the Parry Lands—Pitch Lake—Point Fortin area, where extensive alterations and additions are in progress, including the building of a deep-water pipe-line pier. When this is completed there will be five loading terminals, all situated in the sheltered Gulf of Paria, or west, coast, capable of accommodating ocean-going tank steamers. There

Jan 1, 1933

By R. Kirk

The problems of getting air to the working face of a mine (or perhaps the problems caused by not getting air to the working face) have led to the development of an analogue system in England that reputedly bypasses many of the drawbacks that such systems have encountered in the past. The unit was developed for the Wolstanton Combined mine, an underground operation consisting essentially of three collieries situated in the center of the North Staffordshire coalfield. This combination of workings, which employs a total of eight shafts, brings with it complex ventilation problems, and in order to study these problems and to assist in the control of the established ventilation system, a Ventilation Analogue has been designed and installed to permanently represent the mine's ventilation system.

Jan 4, 1964

By C. Richard Tinsley

INTRODUCTION Documentary complications arise from the risk apportionment in project financing which generally means that once the project is up and running and has satisfied the lender's completion test, the loan agreement specifically limits the lender's recourse to the project and its assets. It is the purpose of this paper to describe the special considerations which apply to industrial minerals projects and explore the reasons why so few project financings are negotiated in this industry. SIZE Small projects do not warrant the relatively high costs of negotiating and documenting project financing. The extent of the documentation is directly proportionate to either (a) the degree of risk apportionment, or (b) the amount of control given to lawyers to negotiate the documents. Although one would like to believe that project-finance documentation could be off-the-shelf, it is almost always necessary to tailor the documents to the mine development itself and the individual desires of the borrower. Accordingly, the documentation costs and initial expenses are seldom less than $40,000, and for complex projects can reach $400,000. In addition, banks often charge an up-front fee to partly compensate them for their staff time and partly to increase their yield on what is deemed to be a "riskier" loan asset. Another factor is the generally lower debt:equity ratio when bankers are uncertain of the accuracy of the cash flow projections. The ratio of the amount of cash flow left over after debt service to debt service itself is a key tool for project finance (debt service coverage). Bankers will require a higher coverage ratio for industrial minerals projects because of the relatively higher uncertainties in the following categories: Prices Markets Geology/Quality Transportation Environmental This, in turn, means that lower debt:equity ratios are the norm for new industrial minerals projects. INDUSTRY STRUCTURE It is hardly worthwhile to generalise about a field as diverse as industrial minerals, but there are four other structural reasons why project financing has not been widely applied. 1. The most obvious example is the predominance of small-sized operations, largely a function of transportation economics. Geological conditions also contribute to their dispersion. 2. Often, the product is only a small part of a company's business in contrast to many petroleum, metals, or coal companies whose sole business is the production of the raw material. The construction industry is a good example here for cement, gypsum, crushed stone, sand and gravel, and the drilling-mud services business for barite and bentonite. A company is unlikely to jeopardise its main business through the failure of a project financing on one of its key inputs. The corrollary is that the mined input is often regarded as a cost centre and not run on the sort of economic basis suitable for project financing. 3. There may be a reluctance to reveal key aspects of an industrial minerals venture to an outsider for purely competitive reasons. Unlike the other minerals industries which readily share technical information at plant visits and

Jan 1, 1985

By Andrew A. Blair

The increased importance and value of chemical analysis in connection with metallurgical operations is largely, if not entirely, due to the increased accuracy of the analytical methods used for the quantitative determination of the foreign elements always associated with the metal operated upon. This applies especially in the working of iron and steel, and to the determination of the amounts of such elements as phosphorus, carbon, and silicon. The influence of greater or smaller amounts of these elements upon the physical properties of iron and steel will be better understood when the proper experiments shall have been made upon samples whose chemical composition is known with almost absolute certainty. From the present standpoint of analytical chemistry, it is easy to see that at least one reason for the failure of many attempts to solve this problem, is the inaccuracy of the analytical methods used. Even at the present time the frequent want of agreement (over and above the unavoidable error due to manipulation) between chemists working on the same sample, leads one to think that there is still at least a choice in the methods used. It is true that very frequently a faulty method in the hands of a skilful analyst may be made to give corroborative results

Important chemical and other technical engineering work necessary, for the prosecution of this war is being carried on by the Bureau of Mines Experiment Station, at Washington, D. C. The services of trained men of the following classifications are urgently needed Bacteriologists Instrument makers Biologists Laboratory Assistants Chemists, Inorganic Laborers Chemists, Organic Machinists Chemists, Physical Physiologists Chemists, Electro- Plumbers Chemical Engineers Steamfitters Draftsmen Stenographers. Electrical Engineers Skilled labor of various kinds If your training fits you for any of these occupations, send to the Bureau of Mines, American University Experiment Station, . Washington, D. C. for blank forms. When properly executed and returned by you, these forms will be placed on file, and when a vacancy occurs you will be considered for it and will be notified if your services are desired. If you are a registrant in the draft, and have not yet been- ordered to camp, it may be possible to have you immediately inducted into the service for work here. If you are not in the draft, but feel that you wish to serve your country in the present crisis, you can enlist, or serve as a civilian. Serve your country where you can serve it best. VAN H. MANNING, Director.

Jan 6, 1918

By L. L. Hirsch, W. M. Parris, P. D. Frost

IT has been established that titanium alloys con- taining sufficient amounts of ß-stabilizing elements, such as iron, chromium, or manganese, can be age hardened.' Adenstedt, Pequignot, and Raymer2 showed that age hardening occurred in a Ti-15 pct V alloy at room temperature after it was quenched from a temperature in the ß-phase region. During a recent investigation of the heat-treating characteristics of binary Ti-Mn and Ti-Cr alloys at Battelle, further evidence of low temperature aging was found. Appreciable hardening occurred in some of these alloys at aging temperatures as low as 212 OF (100oC). Indeed, the brief heating period employed for mounting metallographic specimens in bakelite resulted in hardening. It was felt that further information on this low temperature aging phenomenon would be of general interest in view of the large amount of work currently being done on titanium alloys. The alloys examined in this investigation were arc-melted in a water-cooled copper crucible as 3/4-lb ingots. Du Pont Process A sponge was used as a base material. The arc-melted ingots were forged at 1700" to 1800°F (927" to 982°C) and hot rolled at 1450°F (788°C) to 14 gage (0.064 in.) sheet. Small specimens were heated in argon at 1742°F (950°C) for 30 min and quenched in various liquid media or air cooled. They were then mounted in a room-temperature-setting resin and given a metallographic

Jan 1, 1954

By Harry H. Nowlan

A heavy development campaign progressed during the year 1936 in South Texas1, following up important discoveries made in 1935. Oil and gas wells completed during the year were 1473 against 704 in 1935. The drilling program reached its peak of operations in June in consequence of offset requirements made necessary principally in Duval County in the Seven Sisters, Loma Novio, Lopez and Cole fields. There were six new fields discovered during 1936 as follows: Rhode in McMullen County; Peters, El Mesquite and North Kohler in Duval County; Wood in Starr County and Colorado in Jim Hogg County. No discovery of unusual consequence was made during the year. The pools mentioned above are simply in the primary stages of development. The most intensive exploratory work during the year was in Duval, Webb and Zapata Counties. Considerable activity also prevailed in Starr and Brooks Counties. Much significance is attached to the California Company's discovery in the Alta Mesa field in Brooks County, which is considered to be a deep-seated salt dome. The Comitas field, in Zapata County, developed some surprisingly good production in a shallow sand at 900 ft. and is being followed by a heavy wildcat campaign throughout that area in search of like production. In Starr County an active wildcat campaign is in progress in a continued effort to find new fields northwest of the Sam Fordyce field, in Hidalgo County. This play continues in a northerly direction through Starr and Jim Hogg Counties. New Fields Rhode.—The Rhode field, in southeastern McMullen County, was opened in May by the Magnolia Petroleum Co. with a gas well in the Whitsett (Upper Jackson) sand at a depth of 1810 to 1822 ft., this test is located in the southeast corner of sec. 86 on the Rhode ranch. Four gas wells have been completed, proving up a gas area of 1000 acres, more or less. Development will be slow because of lack of market for the gas.

Jan 1, 1937

By Peter N. Calder

This paper deals with the reinforcement of igneous rock slopes at three open pit iron ore trines in northern Canada. The pits involved utilize overall slope angles in excess of 60º with ultimate depths in the order of 250 m. Three case studies are described. The first concerns the reinforcement of a 300,000 Ton undercut rock wedge, approximately 70 m in height. This was accomplished using 20 cm diameter steel bales, installed in 25 cm diameter vertical holes, and a cement-sand grout. The second involves the reinforcement of a 40 m wide diabase dyke which had been continuously failing as the pit deepened. A unique form of rock reinforcement was used in that the entire mass of the undercut dyke was not pinned to the wall. Rather an interlocking effect between individual blocks within the dyke was relied upon. A third concerns the reinforcement of a berm which was undercut by the contact between the ore and waste. This reinforcement was also accomplished using a combination of steel bales, rods and cement grout.

Jan 1, 1982

Jan 1, 1907

By E. T. Turkdogan, B. B. Rice

Desulfurization of limestone during and subsequent to calcination has been investigated using U.S. Steel's Rogers City quarry-Michigan limestone cut to 25-30-mm diam spheroidal shapes. The experimental observations indicated that the sulfur present as iron pyrite in commercial limestone is oxidized partly to SO, during calcination and partly converted to sulfides (FeS, CaS) and CaSO4. If calcination is carried out under oxidizing conditions, most of the sulfur is converted to CaSO4, which can be removed from burnt lime readily in CO,-CO mixtures, the higher the CO content the faster is the rate of reaction. In the 30-mm-diam spheroids gas diffusion in the pores of limestone and burnt lime is fast relative to rates of the desulfurizing reactions. Over the temperature range investigated, e.g., 850° to 1200°C, there is internal desulfurization.

Jan 1, 1974

By R. W. Mancantelli, J. R. Woodward

In 1947 a large low grade deposit of uranium was located in the northwest corner of Saskatchewan, in the Beaverlodge property of Eldorado Mining & Refining Ltd. Most of the values occur as thin seams and as coatings on other minerals, and the ore, which is light and friable, is not amenable to the usual gravity methods of concentration. The acid leaching process developed to retreat the company's Port Radium tailings was also impractical, as the percentage of carbonates is high and the percentage of sulphides relatively low. Construction of the mill building and installation of equipment, both scheduled for 1952, awaited selection of a satisfactory ore dressing process on or before Oct. 1, 1951. An extensive research program on dressing of ores from the Ace mine therefore was undertaken by the Mines Branch in Ottawa, a research team at the University of British Columbia and an ore dressing group at the company's Port Hope refinery.

Jun 1, 1955

By H. C. Rolseth, R. H. Kohler

Jet channeling made its entry into the granite industry in 1955 and quickly gained acceptance as an economical method of quarrying. Developed by the Linde Division of Union Carbide Corp., this method employs a small rocket-jet burner with a high-temperature, high-velocity exhaust flame that causes granite to disintegrate. It can thus make continuous vertical cuts to free large blocks from granite formations. The Thermal Spalling Process The effect of a thermal device on rock depends upon the rock's spallability. In simplest terms, spalling is the decrepitation resulting from differential expansion of rock crystals due to thermally induced stresses.1 the individual rock properties influencing the spalling characteristic are so numerous and their interaction is so complex that it has so far been impossible to predict with accuracy the reaction of any particular rock to a high-temperature source of heat. Perhaps computers will eventually make such predictions possible, but for the present it is necessary to impose the thermal shock conditions on a sample of the rock to establish its spalling characteristics. The properties most favorable to a high degree of spallability are: (1) Large linear thermal expansion at temperatures below 700º C. (2) High thermal diffusivity at temperatures below 400º C. (3) Equigranular interlocking structure with little or no fine-grained clay or mica alteration products. (4) No significant amounts of soft, low-melting, or elastic minerals or materials which yield after thermal decomposition.

Jan 7, 1969

By Pedro G. Salmon

The broad general distinction between primary and secondary batteries lies in the fact that in the former the current is produced by the consumption of one or both of the elements composing the cell, while in the latter the elements retain their form as such, and merely pass from one state of chemical combination to another. Much has been said in condemnation and but little in praise of storage-batteries; yet, notwithstanding the severe criticisms passed upon them, the skepticism with which electricians have viewed them, and the ignorance with which they have been handled, they continue to push their way into use. Their manufacture has now become a well-defined and established industry.

Jan 1, 1890

By W. M. Reilly, Martin E. True, O&apos

A technique, equipment, and a compound have been developed and field tested for sealing tubing joint thread leaks without removing the tubing from the well. This eliminates the necessity of killing the well with possible damage to the producing formation, which could result if it were exposed to drilling mud. A thread sealing compound, developed and tested in the laboratory, is introduced into the tubing and squeezed into the joint to eliminate the leak. A high percentage of successful field applications have eflected an appreciable cost reduction in repairing leaking tubing strings in East Texas and in the Louisiana Gulf Coast area. INTRODUCTION In producing oil and gas wells the industry has been plagued with a never ending problem of tubing connection leakage. This situation is becoming increasingly more significant as more gas wells are placed on production and as higher pressures are encountered at greater depths of current drilling. Substantial progress has been made in minimizing thread leaks by careful handling and cleaning of joints and by the use of improved sealing compounds in combination with controlled makeup. But even with the use of the best known methods and sealing materials during initial makeup, occasional leaks through tubing joint threads appear inevitable. In some instances, tubing joints in high-pressure gas wells have been found to leak gas at relatively less pressure than that at which the tubing had been tested satisfactorily using liquid. Many expedients have been employed to prevent the physical replacement of tubing when leaks have developed. Perhaps the most commonly used is the sodium silicate treatment in which the solution is lubricated into the tubing to form a crystalline plug in the leak. Generally, any benefit realized is of a temporary nature. In addition to field studies on handling and makeup of tubing, extensive laboratory work has been undertaken on the development and testing of thread dopes.' Also, substantial effort has been devoted to testing tubing joints using high-pressure gas as a pressure medium.' The results of this work have emphasized that tubing joints are susceptible to occasional leaks, especially when subjected to relatively high differential pressures. To cope with the problem of leaking connections, an extensive investigation was undertaken to devise means of sealing leaks without removing the tubing from the well and without reducing the inside diameter of the tubing. The purpose of this paper is to present a technique, together with the associated equipment and compound, which have been developed for effecting a seal of leaking tubing in place. DISCUSSION Work was initiated simultaneously on two ventures: (1) to develop a satisfactory leak sealing compound and (2) to develop tools necessary to find the leak and place the compound. Leak Sealing Compound In the development of a sealing compound, tests were conducted on those compounds commercially available which include: (1) conventional thread lubricants, (2) thermo-setting resins and (3) other materials which held promise of effecting a seal. Although none proved completely satisfactory in their available form, two commercial compounds proved nearly equally effective in sealing leaks during laboratory tests after proportioned quantities of graded silica had been added. Field usage has indicated that the preferred compound is one prepared of an aluminum-stearate base thinned to the proper constituency and carrying a mixture of fine mesh graphite and graded silica. The compound developed by Humble Oil & Refining Co. is designated as Tubing Thread Leak Sealant 800. Placement Tools and Technique In developing tools to detect joint leaks and to place the sealing compound, work was done initially on wireline equipment. Preliminary designs were completed of a tool somewhat on the order of a pressure bomb to test individual joints with gas at high pressure to determine if the joint was leaking. An entirely different tool equipped with opposed packers was intended for placement of the sealing compound at high pressures in each leaking joint. The application of these tools

Jan 1, 1958

By Rex T. Ellington

The fluidized bed is an effective method for investigating retorting phenomena and possibly a commercial means of retorting oil shale. Both were examined by Sinclair Oil (now part of Atlantic Richfield Co.) in the period 1965-1698. The results of the work show that the presence of an oxidizing environment during retorting results in loss of oil yield which indicates that vapor phase oil burns in preference to combustion of coke on spent shale. Consideration of hardware indicates that there are several possibilities for commercial embodiment. As a companion to shaft-type retorts the fluidized bed could have good potential. Realistic assessment of costs suggests that further development may have to wait commercialization of another process.

Jan 1, 1974

By James B. Vance, Parviz Mottahed

An extensive research program has been carried out at PCS Mining for some time into the use of high frequency microseismic emissions in the range of 30-200 kHz for roof fall warning in the mines. A laboratory investigation on loaded samples of potash has established a close correlation between acoustic emissions and the applied load. The tests also indicated the occurrence of the Kaiser effect. The positive and encouraging response from underground testing and controlled laboratory testing has lead to the extension of the investigation into correlation of the high frequency microseismic emissions and the change in stress distribution due to mining. Hydraulic borehole pressure cells were installed at different depths ahead of the advancing boring machine. The output due to the stress change and the microseismic event count was monitored by a continuous chart recorder. This paper discusses the results of this instrumentation. The results confirm the strong correlation between the two measured parameters and outlines future areas of research for the use of the high frequency microseismic emission techniques in quantifying the changes in stress distribution.

Jan 1, 1984