Search Documents

By E. W. Edson, F. W. Hertal

In some fields the problem of mud fluid is simple and easy of solution. But in the Ventura Avenue field the acquisition and disposal of good drilling mud is not the least of the problems that confront the operator. In fact, mud fluid in the Ventura Avenue field is a very important factor in the drilling of the wells. It is quite probable that many of the factors affecting mud in this field will not be found in most of the fields with which the reader is familiar. However, in the fields where the mud fluid causes no apparent problem it is probable that some of the points brought out in this paper could be used to economic advantage. In fields where caving and squeezing formations and high gas pressures are present, as in the Ventura Avenue field, it is believed that application of methods outlined will be of great assistance in drilling wells. On account of the sandy nature of the formation and the lack of suitable shale bodies in the strata drilled through in the Ventura Avenue field, the wells make practically no mud during drilling. It is necessary therefore to supply drilling mud to the wells that will carry the drill cuttings to the surface, and also will " wall up" the drill hole and prevent the sandy formations from caving. Mixing and Handling Mud Fluid The clay used to make the mud fluid is obtained from a shale stratum in the upper Pico (Plioccne) formation found about a mile on either side of the field. Since high gas pressures and caving formations were first encountered in the Ventura Avenue field and mud fluid was needed to combat them, the mixing of this mud fluid has gone through a process of evolution. First, the clay was mined and hauled to the derrick, where it was shoveled into the well and left for the churning action of the bit to mix into a mud in the hole. The next move was the construction of a mixer to mix the clay to a mud fluid which was pumped into the well. These mixing

Jan 1, 1930

By C. W. Spencer, K. A. Semlak, F. N. Rhines

IN an effort to obtain a better understanding of sintering in the presence of a liquid phase, it was decided to study the rate of capillary rise of a relatively low melting liquid metal in a higher melting metal powder compact. By assuming that the metal powder compact consists of a great number of parallel capillary tubes and that the flow of liquid

Jan 1, 1958

By R. Schutte, L. W. Trevoy

Commercial production of heavy minerals from plant tailing streams is undergoing study by Syncrude Canada Ltd. When tar sand from an open pit mine is processed and upgraded to synthetic crude oil, heavy minerals can be recovered from the extraction circuit and can be upgraded to provide concentrates of zircon and titanium minerals. The titanium minerals concentrate, consisting of a mixture of ilmenite, leucoxene, and rutile, can be utilized as recovered or can be upgraded to synthetic rutile. With the construction of further synthetic crude oil plants in Western Canada a large reserve of heavy minerals will become available for production.

Jan 1, 1983

By R. D. Pehlke

THE impending commercial importance of iron-aluminum alloys has served as a stimulus for re- search on the preparation and properties of these alloys. However, the activities of the components of the binary system remain undetermined. The experimental determination of the thermodynamic properties of binary solutions of iron and aluminum has been hindered by the high liquidus temperatures

Jan 1, 1959

By Arthur H. Redfield

In estimating the unmined petroleum reserves of Central America, it is not feasible to employ the methods that have been worked out in thc oil fields of the United States. No producing wells have been brought in and no drilling sections have been made public. It is accordingly necessary to fall back on a crude "barrels per square mile" estimate. The method chosen is a comparison of the structure of the foreign field of unknown reserves with that of some supposedly analogous North American field of which the reserves have been estimated. This method makes no pretense at scientific accuracy, but furnishes a working basis for an estimate. The areal geology of Central America is illustrated in the inap prepared by Sapper and more recently in the geologic map of North America accompanying U. S. Geological Survey Professional Paper No. 71, "Index to the stratigraphy of North America." Disregarding for the present the narrow Quaternary coastal plains and alluvial deposits of the river valleys, three chief zones may be distinguished. These arc: A zone of late eruptive and effusive rocks; a zone of highly folded prr-Cambrian(?) or early Paleozoic crystalline schists and slates, considerably intruded by pre-Tertiary plutonic rocks; and a zone of more or less folded sediments, chiefly of Cretaceous or Tertiary age. The zone of late eruptive and effusive rocks of Central America begins in southeastern Chiapas, Mexico, and extends, with increasing breadth, across southern Guatemala, across practically the whole of El Salvador, and across southern Honduras to the valley of Rio Goascorhn, where the igneous zone attains a width of about 100 mi. (160 km.) East of the Goascordn Valley late eruptives and effusives play a subordinate part, being confined largely to thc Departments of Valle and Choluteca. Dikes and sills of igneous rocks intrude the sedimentary formations of central and northern Honduras. Late igneous rocks cover about four-fifths of the area of Nicaragua. In Costa Rica, late igneous rocks form the diagonal ranges of the Sierra de Guanacaste and the Cordillma Central, and play a part in the upbnild-

Jan 1, 1923

By Arthur H. Redfield

In estimating the unmined petroleum reserves of Central America, it is not feasible to employ the methods that have been worked out in thc oil fields of the United States. No producing wells have been brought in and no drilling sections have been made public. It is accordingly necessary to fall back on a crude "barrels per square mile" estimate. The method chosen is a comparison of the structure of the foreign field of unknown reserves with that of some supposedly analogous North American field of which the reserves have been estimated. This method makes no pretense at scientific accuracy, but furnishes a working basis for an estimate. The areal geology of Central America is illustrated in the inap prepared by Sapper and more recently in the geologic map of North America accompanying U. S. Geological Survey Professional Paper No. 71, "Index to the stratigraphy of North America." Disregarding for the present the narrow Quaternary coastal plains and alluvial deposits of the river valleys, three chief zones may be distinguished. These arc: A zone of late eruptive and effusive rocks; a zone of highly folded prr-Cambrian(?) or early Paleozoic crystalline schists and slates, considerably intruded by pre-Tertiary plutonic rocks; and a zone of more or less folded sediments, chiefly of Cretaceous or Tertiary age. The zone of late eruptive and effusive rocks of Central America begins in southeastern Chiapas, Mexico, and extends, with increasing breadth, across southern Guatemala, across practically the whole of El Salvador, and across southern Honduras to the valley of Rio Goascorhn, where the igneous zone attains a width of about 100 mi. (160 km.) East of the Goascordn Valley late eruptives and effusives play a subordinate part, being confined largely to thc Departments of Valle and Choluteca. Dikes and sills of igneous rocks intrude the sedimentary formations of central and northern Honduras. Late igneous rocks cover about four-fifths of the area of Nicaragua. In Costa Rica, late igneous rocks form the diagonal ranges of the Sierra de Guanacaste and the Cordillma Central, and play a part in the upbnild-

Jan 1, 1923

By Edward R. Bingham, John R. Suffron

A comprehensive program to rehabilitate waste disposal areas is in progress at the integrated primary copper production facility at White Pine, Michigan. The various aspects of the program are described, including cooperative studies with State and Federal agencies in revegetating efforts and wildlife management and also waste disposal practices as they relate to reclamation planning.

Jan 1, 1976

A HIGHLY successful joint conference on coal-mine transportation was held at Pittsburgh on Oct. 20 by the Pittsburgh Section of the American Insti-tute of Mining and Metallurgical Engineers and Mining Section of the Engineers' Society of Western Pennsyl-vania. C. E. Lesher, executive vice-president of the Pittsburgh Coal Co., presided over 215 members and others in the morning and Graham Bright, sales en-gineer with the Mine Safety Appliances Co., presided over about 180 in the afternoon. There were four prepared papers and much discussion, as well as a good luncheon between the sessions. Mechanical loading in the Pittsburgh district was discussed by L. E. Young, production vice-president of the Pittsburgh Coal Co. More companies in this district are using loading machines, more types of machines are being tried, and more coal is being mined by them than heretofore. The draw-slate above the Pittsburgh seam is the main problem; but devices for supporting and moving draw-slate are being tested. Except in two mines, the slate is being taken down. The fundamentals of the machines are similar, but the electrical drive and other parts have been improved. The problem is to recover or move as much coal as possible without hand labor. Methods of cleaning coal must be improved to meet the new methods of loading. The Pittsburgh Coal Co. has ten Joy machines and others are under order, a Myers-Whaley machine, Jeffrey conveyors, and Eichoff conveyors. The last mentioned are used in entries and other conveyors in rooms. At Montour No. 10 mine, one Joy machine is worked in rooms and one in entries.

Jan 12, 1927

By Toshiki Hayashi, Shoichi Asahina, Kenitsu Hosokura

Sumitomo Metal Mining Co., Ltd.'s Kunitomi Smelter has been treating in the blast furnace copper concentrate containing bismuth. The bismuth is concentrated in the electrostatic precipitator dust and the converter dust. Bismuth contained in the converter dust is leached by a mixture of salt and sulfuric acid, and is then recovered by a cementation process using scrap iron. The bismuth cake thus recovered and the electro- static precipitator dust are reduced to crude bismuth metal which is further refined to a high purity bismuth metal by the pyrometallurgical refining process. Details of this process are elaborated in this report.

Jan 1, 1976

By Alfred F. Brainerd

The subject of the supply and the quality of the iron-ore and coke of this State has suffered exaggeration and misrepresentation in both directions. Unsophisticated persons have made extraordinary reports of quality and richness, which could not be supported by facts; while, on the other hand, experts have selected inferior samples, and upon the average of these, which was not by any means the average known to our practice, have based comparisons favorable to other States. Our furnace-records give much better testimony as to the run of our ores, the calorific duty of our coke, and the burden and blast which it will bear. Some of them show poorer ore-mixtures than others; but it is safe to say that the Birmingham furnaces produce from 40 to 60 per cent.. of iron from a mixture of equal parts of the leanest and the richest ores, as classified in large quantities. And certain performances on record here, while they do not represent the regular or average practice, ma: be fairly urged as proof of excellence of raw material, since they would otherwise have been impossible, even as exceptional achievements. Thus oue of our furnaces has made iron with 2500 pounds of coke to the ton of 2300 pounds (Mr. Stratton, 1888); another, with a ton of coke to the ton of iron (Mr. Gordon, 1888); another, with 1.27 ton of coke to the ton (2300 pounds) of iron, the product in the last case being from

Jan 1, 1889

By Ellsworth Daggett

The Berlin gold-quartz mine is situated in Nye county, Nevada, on the west flank of the Shoshone range, about 40 miles south and 30 miles west from the town of Austin, the county-seat of Lander county. The distance from Austin is about 60 miles by stage-road. The outcrop of the vein, at the top of the incline-shaft, is situated just at the base of the mountain proper, almost exactly at the intersection of the mountain-side with the gravelly bench that slopes for about three-quarters of a mile to the flatter sage-brush plain, or desert valley, below. The vein itself consists almost entirely of quartz, with perhaps 2 per cent. of sulphide of iron, copper, lead, zinc and antimony, and perhaps a trace of some of the compounds of tellurium with gold and silver, although none of the latter have been as yet positively identified. The relative proportion, by weight, of silver and gold in the ores, varies in different parts of the vein, from 12 silver for 1 of gold, to 7 silver for 1 of gold. The quartz vein-filling is usually frozen fast to the walls, and is very hard and compact, seldom showing the friable, fissured, or shelly structure often to be found in quartz-veins. Comparatively little evidence of relative motion of one wall of the vein upon the other is to be found—a fact indicating that during the formation of the vein, and prior to the extensive movements herein described, little disturbance had taken place. No evidence whatever of metasomatic origin has been observed. On the other hand, occasional occurrences of comby structure, in which the axes of the quartz-crystals are at right angles to the plane of the vein, rather indicate deposition from solution in a pre-existing fissure. Spurs, or branches, and small parallel veins, while not en-

Jan 1, 1908

By R. C. Croft

Many chemical methods of upgrading ilmenite to enhance its titanium dioxide content involve reduction of the FeO in this mineral followed by solution of the metallic iron produced. While the use of most mineral acids for this purpose entails acid regeneration or salt disposal problems, these difficulties can be overcome with carbonic acid. Satisfactory rates of iron removal have been achieved at temperatures below 100° C and at CO, pressures up to 600 psi. Lowering of gas pressure over soluble bicarbonate solutions permits recovery of CO. and precipitation of iron oxide. The removal of the manganese, often present in ilmenites, is also feasible with these treatments.

Jan 1, 1972

By T. Leser, A. W. Jenike

The problems of caving and underground subsidence can be considered as the failure of a highly compacted rock and its subsequent flow in the form of broken rock. The problem is complex because the propagation of failure and flow have to be considered simultaneously; the yield strength of the virgin rock and the broken rock are different; and, while under certain conditions it is sufficient to consider the virgin rock as homogeneous, the density and the yield function of broken rock are both pressure and time dependent. A study of the failure and flow of solids with a pressure dependent yield function has been published recently by Jenike.' In this paper the density of the broken rock is assumed to be only time dependent and the consequences are examined in the case of one-dimensional vertical subsidence into an initial cavity. The following describes an attempt to develop a tool which, in combination with other tools, may lead to mathematical solutions of real problems of caving and subsidence. STATEMENT OF THE PROBLEM An underground cavity of horizontal cross section 4 = 1 and height 6 is assumed to exist at some depth below the surface. At the time t = 0 rock above the cavity fails and completely fills out the cavity with expanded broken material. With passing time the broken rock consolidates and subsidence proceeds continuously upuard in a vertical shaft. The phenomenon is one-dimensional (see Fig. 1). The problem consists of finding the displacement and the velocity with which the frlmt of the subsidence (wave front) moves upward as a function of the time and of the rock properties. DIFFERENTIAL EQUATIONS CONTROLLING THE PHENOMENON With the assumptions that the broken rock is a continuum and that the subsidence occurs continuously, we can apply the one-dimensional differential equation of contitiuity (conservation of mass) and the equation of preservation of momentum The latter equation is replaced by an assumed relation based on experience, which takes care of the

Jan 1, 1962

By Arthur F. Wendt

In the manufacture of charcoal-blooms, washing or cleansing of the ore from adhering gangue has been practiced for many years. A sluice-box is even to-day used for that purpose in the Southern Appalachian Mountains. For the Lake Champlain bloomaries hard magnetic ores are crushed with stamps and then sluiced or jigged in hand-jigs. The stamps used in the Lake Champlain region are of the most primitive kind. They consist of a trip-hammer, dropping on a perforated cast-iron plate, through which the crushed ore escapes. Only friable rock can thus be successfully treated. To render the raw ore friable, a calcining or burning in piles on a bed of cordwood is resorted to. An expense of 35 cents per ton of crude rock treated is thus incurred. The crushed ore is shovelled or otherwise fed into jigs without previous sizing, except such as is incidental to crushing through the perforated bottom of the stamping-machine. In jigging this ore, it is allowed to pass through the bedding into the "hutch." The tailings are scraped off and wasted. They contain a large percentage of fine ore. In many instances, this is regained by subsequent sluicing. Such was the condition of the industry, when the writer's attention was first called to it in 1882. No attempt had been made to introduce into thiS branch of ore-dressing the notable improvements adopted in concentrating the ores of other metals. The result of the writer's investigations was the building in 1882 of the "Crown Point Separator." At the Crown Point Mines, N. Y., lean ore unfit for the blastfurnace (containing less than 331/3 per cent. of iron), was concentrated and used in the bloomary connected with the mines. The ore was burned here as elsewhere, and treated as described. The plant designed by the writer for Crown Point, is nearly a counterpart of that since erected by Messrs. Copeland and Bacon, contractors, for the Theal mine, Putnam County, New York, which is illustrated by the accompanying plate. The only difference is in

Jan 1, 1885

By Robert C. Collins, Clifford L. Jewett

The development and production of artificially colored roofing granules have been key factors in the success of the asphalt roofing industry. They provide protection for the asphalt from solar radiation and satisfy the home-owner's desire for a wide range of attractive colors. As a result, the asphalt shingle has become the most commonly used roofing material today. In addition to providing a stimulus to the asphalt roofing industry, artificial methods of coloring granules completely changed the nature of granule production from one of quarrying, crushing, and screening to a complex technical operation. Today's roofing granules are the result of many years of research, and they are produced in modern plants to exact specifications. History Asphalt roofing materials available today are the product of a long evolution of technological development. Forerunners of the present bituminous products, appearing as early as 1780, were primitive constructions of burlap saturated with crude tar or pitch. An early improvement to this basic effort was the dusting of talc, mica, or other finely ground material on the coated surfaces to keep the roofing from sticking to itself in storage. At times some pigmentation was added with the dusting material for initial color, but this was far from satisfactory. In fact, this early product possessed none of the qualifications of a good roof surfacing material. It was not economical; it was difficult to handle and apply; it was not attractive; it provided no resistance to fire; and it would not withstand the elements as well as other products then in use. Methods and machines were soon devised to saturate endless webs of felt with asphalt from the fast-growing petroleum industry. Even though saturated felt became available, this product of rags and wood fiber had almost the same limitations as burlap and tar. Even with heavier coatings of asphalt applied to both sides of the sheet for rigidity and longer life, the product still lacked color and fire resistance. Further, it was found that constant exposure to the sun soon caused the asphalt to become brittle, and it eventually cracked and leaked. This led to the first important use for crushed mineral products on asphalt-coated shingles and provided the key to the subsequent growth of the asphalt roofing industry. When a layer of crushed mineral was embedded in the surface exposed to the weather, the asphalt coating was protected from ultraviolet light and retained its elasticity over a much longer period of time. In addition to this protection, the mineral surfacing provided some resistance to fire. Fire resistance in the past had been found only in the expensive slate or tile roofs and the unattractive and expensive metal roof coverings which were then available. The most common mineral granule applied to the early asphalt roofing products as they began to make their first significant advances after 1900 was screened waste from slate quarries. Slate granules being available in dull shades of red, green, black, purple and a few other miscellaneous colors did provide a degree of color. Since slate has a flat platelike cleavage, it provides a cheap protective cover for the asphalt-coated sheets. Records show that coarse slate screenings were used for asphalt roofing as early as 1906. As the asphalt roofing industry developed, many other natural colored rocks and minerals were used to coat the surfaces of the roofing. The list included silica

Jan 1, 1975

By Charles J. McMahon

In a recent paper, Floreen and Hayden report that additions of the noble metals iridium, rhodium, ruthenium, and platinum to Fe-C alloys containing 0.03 to 0.08 wt pct C act to significantly reduce the ductile-to-brittle transition temperature in a notched-bar impact test. They compare these results with the similar, well-known effects of nickel and manganese additions, and they note that this supports the hypothesis that addition of austenite stabilizers enhances notch toughness. Although not attempting to offer an explanation for this, they suggest that it might be found in an alteration of the bonding characteristics of the bcc lattice of iron by additions of elements which tend to stabilize the fcc lattice. While this suggestion appears to have some merit, it should perhaps be held in abeyance until two more likely possibilities have been explored. It is now fairly clear that the beneficial effect of manganese derives from its ability to promote a globular carbide morphology instead of the platelike form found in grain boundaries and pearlite patches in Fe-C al10~s.' Previous work14 has also shown that cleavage fracture in Fe-C alloys of the type tested by Floreen and Hayden originates almost exclusively in the cracking of cementite platelets, and that the ductile-brittle transition temperature is very sensitive to the volume density and size of these carbides. Treatments which lead to development of nonlamellar carbides or fine dispersions of carbides, such as quenching and tempering or appropriate alloy additions, promote toughness by removing the primary mode of cleavage initiation. The effectiveness of manganese in this regard has long been known. Nickel appears to behave in a similar manner, though the effect is perhaps not as dramatic as with manganese.15 However, nickel additions do lead to a definite refinement of ferrite grain size following a given transformation heat treatment, and this in itself acts to greatly enhance notch toughness.'' (The grain sizes of the various heats tested by Floreen and Hayden were not reported, so it is not known how much influence this factor exerted in their results.) In conclusion, it is suggested that one should consider the well-established effects of alloying elements on carbide morphology and ferrite grain size before resorting to more complex possibilities, such as modification of interatomic bonding.

Jan 1, 1969

By Howard J. Smith

For several years this Institute has recorded in its Transactions the various discoveries of potash‡ in America, and the successive stages in the development of an independent domestic potash industry. This paper is intended primarily to continue the record through the year 1935. In retrospect it is not inappropriate to note that public interest aroused in 1910 resulted in the production of some 1090 tons of pure potash in 1915, as a small beginning in the domestic inorganic potash industry, and that the infant industry thus begun reaches its majority this year, following a record production in 1935 of about 600,000 tons of potash salts and exports to no less than 22 foreign countries, including six countries in Europe. This production, with an estimated 200,000 tons of pure potash, may be compared with a production in 1934 of 430,157 tons of salts with an equivalent of 144,342 tons of pure potash. Mine and Plant Improvement During 1935, the American Potash & Chemical Co., at Searles Lake, Calif., began to reap the benefits of its previously enlarged plant facilities, which increased its productive capacity to 180,000 tons of muriate annually. The United States Potash Co., at Carlsbad, N. Mex., improved its operations by installing trolley locomotives and other haulage facilities and is maintaining its development headings two years in advance of operations, with projected plans for orderly mining for years to come. The hoisting shaft at its mine is now equipped to hoist at the rate of 1,000,000 tons annually, and the refinery to produce 150,000 tons of muriate containing less than one per cent of impurities. The Potash Co. of America, at Carlsbad, N. Mex., completed the conversion of its plant from a prospecting to an operating basis late in 1935. The coarse-crushing plant, with a capacity of 150 tons an hour, formerly on the surface, was installed underground, with ore pockets

Jan 1, 1938

By Howard J. Smith

For several years this Institute has recorded in its Transactions the various discoveries of potash‡ in America, and the successive stages in the development of an independent domestic potash industry. This paper is intended primarily to continue the record through the year 1935. In retrospect it is not inappropriate to note that public interest aroused in 1910 resulted in the production of some 1090 tons of pure potash in 1915, as a small beginning in the domestic inorganic potash industry, and that the infant industry thus begun reaches its majority this year, following a record production in 1935 of about 600,000 tons of potash salts and exports to no less than 22 foreign countries, including six countries in Europe. This production, with an estimated 200,000 tons of pure potash, may be compared with a production in 1934 of 430,157 tons of salts with an equivalent of 144,342 tons of pure potash. Mine and Plant Improvement During 1935, the American Potash & Chemical Co., at Searles Lake, Calif., began to reap the benefits of its previously enlarged plant facilities, which increased its productive capacity to 180,000 tons of muriate annually. The United States Potash Co., at Carlsbad, N. Mex., improved its operations by installing trolley locomotives and other haulage facilities and is maintaining its development headings two years in advance of operations, with projected plans for orderly mining for years to come. The hoisting shaft at its mine is now equipped to hoist at the rate of 1,000,000 tons annually, and the refinery to produce 150,000 tons of muriate containing less than one per cent of impurities. The Potash Co. of America, at Carlsbad, N. Mex., completed the conversion of its plant from a prospecting to an operating basis late in 1935. The coarse-crushing plant, with a capacity of 150 tons an hour, formerly on the surface, was installed underground, with ore pockets

Jan 1, 1938

Jan 1, 1942

Jan 1, 1942