Search Documents

By Mark W. Springett

The sampling of precious metal deposits entails inherent problems due to the low mineral abundances, high mineral specific gravities, skewed grade distributions and wide ranges of mineral particle sizes. Sampling practices and precautions are discussed with particular attention to each of the tripartite stages of sampling - sample acquisition, sample preparation and sample assaying. Practical examples of approaches to the sampling problem are given and some examples of significant sources of error are provided from gold and silver deposits in North America.

Jan 1, 1984

By W. F. Laverty

Two recent papers in this journal1,2 contain experimental evidence for an anomaly in the concentration gradient for tracer diffusion. In both papers, the authors suggest that this anomaly is due to a Gibbs' absorption effect. Their hypothesis is that surface active tracer elements tend to remain in or near the surface adsorption layer, thereby altering the diffusion flux and concentration gradient. It is not clear how the anomaly can be explained in terms of an adsorption effect. Surface tension forces act parallel rather than perpendicular to a surface and therefore should affect only the rate of spreading of surface active agents tangentially across a surface. Frenkel3 has given a short treatment of surface tension as a driving force for surface diffusion. While the equilibrium concentration of a surface active agent at the surface of a solution is known to be higher than in the bulk, its chemical potential is necessarily the same. It is difficult to see how adsorption can result in an anomaly in the chemical potential gradient, which is the driving force for diffusion. A more detailed explanation by the authors of the adsorption mechanism is in order. A similar anomaly does not seem to arise where

Jan 1, 1970

By William P. Blake

Eureka has for several years past been known as one of the most important centres of production of argentiferous lead in the country. The average daily yield is now one hundred tons of lead bars, in which the silver and gold of the ore is concentrated. The value of this lead, called " bullion," is about $300 per ton. To produce this quantity of metal, about four times the weight of ore, or say four hundred tons, is required. Most of this ore is supplied by the two leading mines of the district, the " Eureka" and the " Richmond," adjoining claims on Ruby Hill, about two miles from Eureka. There are, however, many other mines from which considerable quan-

Jan 1, 1879

By William P. Blake

(Read at the Amenia Meeting, October, 1877.) EUREKA has for several years past been known as one of the most important centres of production of argentiferous lead in the country. The average daily yield is now one hundred tons of lead bars, in which the silver and gold of the ore is concentrated. The value of this lead, called "bullion," is about $300 per ton. To produce this quantity of metal, about four times the weight of ore, or say four hundred tons, is required. Most of this ore is supplied by the two leading mines of the district, the "Eureka" and the "Richmond," adjoining claims on Ruby Hill, about two miles from Eureka. There are, however, many other mines from which considerable quan-

Jan 1, 1878

By V. D. Perry

AS the traveler approaches Chuquicamata from the seaport of Antofagasta, crossing in a northeasterly direction the 150 miles of coast range and completely barren pampa with its low, rolling hills and broad depressions, the gradual rise to an elevation of 9000 ft is imperceptible, and it is hard to realize that the smoothly contoured hills east and west of the mine are from 10,000 to 11,000 ft above the level of the sea. The deceptive monotony of the scene is relieved only by the background of an unbroken line of lofty volcanic peaks, part of the Andean Cordillera, which rise, snow covered, against the eastern skyline. The drab geographical foreground is matched by the geological monotony of unaltered, gray rock

Jan 1, 1952

By Thomas J. O’Neil

Once again, the United States Congress is debating the minerals depletion allowance. If the past is any indication, the debate will quickly become politicized. Representatives of the densely populated but mineral-poor Northeast will no doubt claim that percentage depletion is sheer robbery of tax dollars perpetrated by corporations to line the pockets of wealthy investors. Many southern and western legislators, on the other hand, will portray the depletion allowance as our only savior from mineral deprivation, blackmail from foreign producers, and a stone-age nonmineral existence. Although this characterization of the usual minerals depletion debate may be overstated, the most unfortunate aspect is that the genuinely important role of the depletion allowance in domestic minerals production is often obscured in congressional hearings. This article will try to provide a basic understanding of the minerals depletion allowance, the underlying rationale, and the increasingly important role the allowance will play in the future. Although the discussions and conclusions can be extended to the metal mining industry in general, most of the examples are drawn from the copper industry.

Jan 10, 1974

By Jack A. Kanz, Samuel R. Shortes, E. C. Wurst

Zinc diffusion into GaAs from the vapor phase through reactively sputtered SiO, films Izas been inrestigated for various zinc pressures at 1000"C. Diffusions were carried out in evacuated quartz ampules with elemental zinc and with various Zn-Ga alloys. Sputtered films have proved effective in lowering surface concentrations and preventing surface deterioration during diffusion. Approxin.ate complenzentary error-function impurity distributions were found when surface concentrations were reduced to approximately 3 -—4 x 10" atoms cm'3 or less with dilute zinc sources or by diffusion through SiO, films. Zinc difhsions in GaAs tlzrough SiO, films produced more planar diffusion fronts than were observed with uncoated zuafers under identical conditions. A) Surface Deterioration During Diffusion. Device technolorn-- in compound semiconductors has been hampered by several difficult problems not normally encountered with silicon and germanium. 111-V and 11-VI compound semiconductors generally have volatile constituents at temperatures used for diffusion. To achieve specific junction depths in reasonable lengths of time, or to obtain particular impurity distributions and doping levels, it is often necessary to use temperatures which cause surface deterioration and erosion of the wafer. The resultant surfaces are generally unsuitable for devices. The type and extent of surface damage depends to varying degrees on the particular environment of diffusion and on the particular impurity in question. The most common type of deterioration results from simple dissociation of the gallium and the arsenic during diffusin.' The deterioration process is significantly enhanced by thermal gradients in the diffusion zone, usually resulting in vapor transport and condensation at the cooler portion of the system. The resulting damage sometimes appears as a general haziness over the surface or an array of pyramidal etch pits characteristic of the particular orientation. Occasionally, erosion of the surface occurs uniformly over the wafer so that surface loss is not readily apparent. Workers in GaAs usually resort to the sealed-ampule type of diffusion system3"5 rather than the more conventional open system used for silicon and germanium. Another type of deterioration results from direct interaction of the impurity with the surface. The form of deterioration may vary from surface alloying, as in the case of zinc, to direct chemical attack and vapor transport of the reaction products, as in the case of sulfur. Surface alloying with zinc occurs at higher temperatures and source vapor pressures.4 The process is largely controlled by the amount of free gallium on the surface of the wafer in equilibrium with the arsenic lost to the system. The group-VI elements, sulfur, selenium, and tellurium, are commonly used donor impurities for gallium arsenide. These elements are characterized by high vapor pressures and high chemical

Jan 1, 1964

By R. A. McClelland

In the development of the Sirosmelt tin smelting process the need has arisen to understand and predict the problems likely to be encountered in optimal furnace operation on larger scales and over wide ranges of operating parameters. To study these parameters in detail with existing pilot plants and production scale plants is prohibitive in terms of cost, time and limitations of furnace design. The Sirosmelt computer model, SMELT, has been developed to simulate the process and to study a range of metallurgical parameters. The model's robust basic form has allowed adaption to a variety of needs. It is now being used to generate data on optimum operating conditions for a commercial scale plant and for operator training.

Jan 1, 1984

By Dermot Macaragh Ross-Brown, Brian Stimpson

Borehole information is often the only source of information on rock conditions at depth during the stage of feasibility studies of a project, and from this data the rock mechanics engineer would like to make some quantitative estimates of rock mass cohesive strength. While judgement and experience will usually play a paramount role at this stage, simple tools for estimating rock mass cohesive strength would be an asset. In this paper, an approximate technique is suggested for assessing the cohesive strength of a randomly jointed rock mass from borehole data on fracture intensity and intact rock strength.

Jan 1, 1980

By Pierre J. Goossens

The coastal Cordillera around the Panama basin is made up of a Cu-rich tholeiitic volcanic belt representing either immature, late Mesozoic, island arc, or oceanic ridge. The same belt is exposed (uplifted) along the western slope of the Cordillera Occidental of Ecuador and Colombia. Ni-lateritic, Cr-podiform, and Pt-(Au) placer deposits are formed there after or within ultramafic bodies of oceanic association. Younger calc-alkaline igneous activity provided the mechanism for porphyry copper and associated ore formation. This Cu (+Mo) mineralization occurs along a narrow belt exposed by the erosion of the volcanic cap. Ag-Pb-Zn(-Au) and Hg volcanogenic mineralizations occur within the calc-alkaline belt, but slightly eastward and only above the copper belt. To the east and in the Venezuelan Andes, Paleozoic and older sediments, volcanics, and metamorphics contain volcanogenic massive sulfide, Pb-Zn, Au, and Cu sedimentary and vein deposits, and sedimentary iron ore and phosphate. The Cenozoic Cu, Ni-Pt-Cr and a portion of Ag-Pb-Zn, Hg, and Au mineralizations occur within or just above the oceanic basement whereas the eastern- most Cenozoic Ag-Pb-Zn mineralizations occur within and above a pre-Cenozoic sialic basement. This continental crust is the northern extension of the Peru-Chilean Andes where no oceanic crust has been preserved, however. Cenozoic metallogeny and subduction relationships are unclear in the Northern Andes. Yet strong structural volcanogenic ore controls exists apparently due to deep strike-slip movement between two plates.

Jan 1, 1977

By R. F. Sheldon

Largest uranium deposit in the Northwest is Dawn Mining Co.'s Midnite mine on the Spokane Indian B Reservation. The orebodies lie along the contact of granite and metamorphosed sedimentary rock and are controlled by faults and shear zones near the granite contact. In the oxidized zone the deposits consist mainly of the secondary uranium mineral meta-autunite; sooty uraninite and primary uranium minerals are known to occur at greater depths. Elevations in the mine area range from 2500 to 3500 ft. The rolling hills and low, rounded mountains are covered with grass and evergreen trees.

Jan 5, 1959

By R. M. Genevray, M. B. Bever, E. J. Suoninen

THE martensitic transformation in the ß-phase of the Cu-Zn system has been the subject of several investigations. The transformation is known to be reversible and to be affected by stress. Its temperature range has been determined as a function of composition. In the investigation reported here, the effect of tensile stresses on the transformation was investigated quantitatively. Some information was also obtained on the thermoelastic behavior of the martensite formed in the first stages of the transformation. Most of the experiments were done with alloy E of an earlier investigation;' this alloy analyzed 60.49 pct Cu and 39.51 pet Zn by weight. The methods of shaping and heat treatment were also essentially the same as those previously used. The stress was applied to the specimen immersed in a cooling liquid. The transformation was followed by measuring the electrical resistance with a Kelvin bridge and the elongation with a cathetometer. Fig. 1 shows the M, temperature as a function of stress. Resistance and strain measurements gave essentially identical values. The results suggest a roughly linear relation between M. and in the range investigated, up to 12 kg s mm". At higher stresses, plastic deformation begins to interfere seriously with this relationship. The increase of M, with stress is consistent with published work on the effect of stress on the martensitic transformation. The slope of the curve, 4°C per kg mm ", is of the same order of magnitude as the corresponding value calculated for steel.' Fig. 1 also shows the difference, AM, between the temperature of 50 pct transformation on cooling, as measured by changes in length, and that of 50 pct reverse transformation on heating. This difference, which may be considered a measure of the hysteresis, increases with stress; the decrease at highest stresses is probably associated with plastic deformation. Preliminary work using only resistance measurements was done with an alloy containing 60.15 pct Cu and 39.79 pct Zn by weight. The results indicated higher values o-F M, in agreement with the known variation of M. with composition.' The effect of stress on M, (2°C per kg mm-') was of the same order of magnitude as that shown in Fig. 1 for composition E. An increase in hysteresis with stress was also found. The following experiment was made in order to investigate a partially transformed structure. A specimen of alloy E was cooled to — 85°C under a stress of 4.7 kg mm-'. Under these conditions, the martensitic transformation started but did not go to completion. The stress was then released and the specimen cooled to — 105°C. Fig. 2 shows the measured elongation c. The first change in the slope of the curve indicates the beginning of the transformation under stress. Removing the load at —85°C caused a decrease in length to the value corresponding to the elastic elongation of the parent phase resulting from the applied stress. Hence, the marten-site formed in the first part of the experiment apparently disappears completely and without hysteresis upon the release of the stress. The increase in length on further cooling indicates renewed formation of martensite. These conclusions are consistent with the concept of "thermoelastic" martensite," which has been confirmed by test." Acknowledgments The authors are greatly indebted to Professor M. Cohen for his advice and encouragement. They also thank F. Paxton for assistance. Thanks are due the American Brass Co. which supplied the alloys. References E. Kaminsky and G. V. Kurdjumov: Zhur. Tekhn. Fiziki SSSR (1936) 6, p. 984. A. B. Greninger and V. G. Mooradian: Trans. AIME (1938) 128, p. 337. "J. E. Reynolds, Jr. and M. B. Bever: Trans. AIME (1952) 194, p. 1065; Journal of Metals (October 1952). 'A. L. Titchener and M. B. Bever: Trai~s. AIME (1954) 200, p. 303; Journal of Metals (February 1954). " 3. A. Kulin, M. Cohen, and B. L. Averbach: Trans. AIME (1952) 194. p. 661; Journal of Metals (June 1952). "J. K. Pate1 and M. Cohen: Acta Metallurgica (1953) 1, p. 531. 'C. Crussard: Comptes Rendus (1953) 237, p. 1709. ' G. V. Kurdjumov: Zhur. Tekhn. Fiziki SSSR (1948) 18, p. 999. G. V. Kurdjumov and L. G. Khandros: Dokl Akad. Nouk. SSSR (1949) 66. p. 211.

Jan 1, 1957

By Charles M. Stone, Dale S. Preece

Introduction The Strategic Petroleum Reserves (SPR) is a national program dedicated to storage of large quantities of crude oil in leached salt caverns in the Texas-Louisiana gulf coast area. The program has required storage in existing caverns at each site and includes plans to leach new ones. The structural stability of each cavern depends on the behavior of the surrounding salt. In the past cavern stability has been predicted based on experience with other caverns in the vicinity. With the development of good non-linear finite element structural computer programs, it is possible to predict stability before the cavern is created. An important step in verifying the applicability of these predictive methods is comparison of analytical and field data. The analytical data come from finite element analyses of a specific cavern where the laboratory determined material properties and an approximation to the cavern geometry are used as input. These comparisons have been made for caverns in the Bayou Choctaw Dome (Louisiana) and Eminence Dome (Mississippi) with reasonably good correlation being obtained between measured and predicted volumetric response of the caverns. This paper discusses 1) the acquisition of material properties, 2) the finite element program SANCHO, and 3) the comparison of analytical and field data for each of the caverns.

Jan 1, 1982

By D. Brabec

Previous studies have demonstrated the possibility of using aqua regia-extractable copper and zinc in plutonic rocks in exploration geochemistry. The present investigation compares this method of extraction with hydrofluoric-perchloric acid attack and bisulfate fusion in terms of precision and discrimination between high and low concentrations. Statistical treatment of data shows that the overall performance of the aqua regia method compares very favorably with other methods of attack.

Jan 1, 1972

By L. A. Panek

When rock is subjected to a load it is deformed. Ordinarily this is observed in a mine as the displacement of one point with respect to another-the deflection of the roof, which may be observed as a convergence between roof and floor; or the extrusion of material from the rib, which may be observed as a decrease of the distance between the rib and the post of a timber set. The effect of excessive pressure may be a rockburst if the rock is strong, or it may be "squeezing" ground if the rock is "soft". Some desirable effects of high stress (high in relation to strength) are the caving of roof in a longwall mining operation, the caving of ore in block caving, and the decrease in mechanical energy required to break down the mineral seam in a retreating pillar-robbing operation. In any case, whether the observable effect of rock load is desirable or undesirable, it is a displacement, and depends on the following four factors:

Jan 3, 1961

By W. F. Burns

(Butte Meeting, August, 1913.) ATTEMPTS were made in 1908, at the Great Falls Works, to produce ingots direct from the Butte precipitate by smelting- the material in a reverberatory refining furnace. The ingots produced in this manner averaged 99.4 per cent. of copper and 0.40 per cent. of arsenic and antimony. The copper content being considered too low, it was decided to cast the copper into anodes and to treat the anodes in the electrolytic plant. No.1 Furnace, in which the precipitate was treated, was a regular cathode refining furnace previously employed in making wire bar, cake, and ingot from electrolytic cathodes. The hearth of the furnace was 24 by 12 ft., having a capacity of 100,000 lb. of cathodes. The furnace was coal fired, and the copper was dipped by means of trolley ladles.

Jan 7, 1913

By W. Myron Davy

For more than a decade the use of the metallographic microscope, by mining geologists, for examining ores has been increasing and conclusions founded upon examinations made by it are found in several recent professional papers of the United States Geological Survey as well as in our technical publications. But most mining men have been slow to realize the positive value of this instrument in their daily work. The reason for this condition is not hard to find. The varied applications, the simplicity of preparation, and the methods of studying a polished section of ore have not been widely published. Papers in technical periodicals have been profusely illustrated by photographs of such sections, special refined methods of procedure for laboratory work have been described, and complete and detailed schemes of identifying the ore minerals have been published in book form.1 But simple and easily applied directions and, what, is more important, light, compact, and inexpensive equipment have not been available. The simplest microscope obtainable is intended for laboratory use and is much too bulky for the average field equipment; at present it costs about one hundred dollars for the instrument alone. Methods previously described for polishing specimens have necessitated electrically driven lap wheels, which are found only in permanent installations. It is small wonder that the examining mining engineer, field geologist, resident engineers, and mill men have looked upon the subject as being too involved for the field and have assigned it to the laboratory investigator. The writer has been interested in this question for some time from the viewpoint of his own work. Being handicapped by the difficulties enumerated, he has designed an outfit that has proved very useful. It is described here and its. applications shown in the hope that it may be of equal value to others, and that a start will be made toward popularizing

Jan 8, 1920

By Harold H. Haman

In view of Twentieth Century advances in mineral dressing technology, most modern metallurgists would be inclined to class jigging as an early, somewhat primitive, representation of their art. The practice of metallic sulfide concentration by jigging is becoming rare. This is so, in part, because the type of ore amenable to the process is becoming rare. It is appropriate, however, that this symposium recognize that a significant contribution of domestic zinc remains dependent upon coarse preconcentration by jigging, and that the state of the art be described even though the theory and applications are already well delineated in technical literature. One of the few areas still using jigging as a major concentrating process is The Upper Mississippi Valley. AREA HISTORY AND JIGGING The Upper Mississippi Valley (UMV) has produced one billion dollars worth of zinc and lead at current prices. The district includes the southwest part of Wisconsin, the northwest corner of Illinois and an adjoining narrow strip of Iowa. Within a total area of 4,000 square miles, important sub-districts cover about 400 square miles. As is widely known, early mining in this district involved shallow lead---crevice deposits of galena that were very selectively mined, hand sorted and cleaned, and then smelted at or near the site. The district has produced almost a million short tons of metallic lead, a very large part of this during the fifty- year period following 1830. Zinc mining began at the end of the civil war, but at a very low rate until about 1905.

Jan 1, 1970

By James R. Cudworth, Joseph C. Mead

The Birmingham district of Alabama has utilized the slag from its blast furnaces consistently since the earliest development of the slag industry. Today there are producers of slag cement who started business in 1900, and who have, under a progressive policy, expanded the number of their products to meet present demands. There are producers of slag aggregates and other crushed slag products who have been successful for periods of over thirty years. There are at the present two companies, Cheney Lime and Cement Co. and the Southern Cement Co., manufacturing puzzolan cement; two companies, Birmingham Slag Co. and Woodstock Slag Co., making slag aggregates and by-products; one company, Tennessee Coal, Iron and Railway Co., a subsidiary of the U. S. Steel Corporation, producing ground open-hearth basic slag for soil conditioning. Two companies, the Sloss Sheffield Steel and Iron Co. and the Woodstock Slag Co., make slag concrete in ready-mix plants and one company, the Superock Company, manufactures fine and coarse slag aggregates under a new granulation process. NO Portland cement is made with slag as an ingredient, because dolomite is used so extensively as a blast-furnace flux that the magnesium content of the slag is excessive. Sources of Slag In the Birmingham district there are 22 blast furnaces, of which the majority are in blast. The present production is 165,000 tons of pig iron monthly; the production in 1935 was 1,297,960 gross tons1. There arc also two blast furnaces at Gadsden and one ferroalloy electric furnaee at Anniston. From these two sources is obtained slag to approximately 1.1 tons per ton of pig iron. History of Development of the Industry The history of the local utilization of slag as an industry probably starts with the Birmingharii Slag Cement Co. This company was

Jan 1, 1938

By Joseph C. Mead, James R. Cudworth

The Birmingham district of Alabama has utilized the slag from its blast furnaces consistently since the earliest development of the slag industry. Today there are producers of slag cement who started business in 1900, and who have, under a progressive policy, expanded the number of their products to meet present demands. There are producers of slag aggregates and other crushed slag products who have been successful for periods of over thirty years. There are at the present two companies, Cheney Lime and Cement Co. and the Southern Cement Co., manufacturing puzzolan cement; two companies, Birmingham Slag Co. and Woodstock Slag Co., making slag aggregates and by-products; one company, Tennessee Coal, Iron and Railway Co., a subsidiary of the U. S. Steel Corporation, producing ground open-hearth basic slag for soil conditioning. Two companies, the Sloss Sheffield Steel and Iron Co. and the Woodstock Slag Co., make slag concrete in ready-mix plants and one company, the Superock Company, manufactures fine and coarse slag aggregates under a new granulation process. NO Portland cement is made with slag as an ingredient, because dolomite is used so extensively as a blast-furnace flux that the magnesium content of the slag is excessive. Sources of Slag In the Birmingham district there are 22 blast furnaces, of which the majority are in blast. The present production is 165,000 tons of pig iron monthly; the production in 1935 was 1,297,960 gross tons1. There arc also two blast furnaces at Gadsden and one ferroalloy electric furnaee at Anniston. From these two sources is obtained slag to approximately 1.1 tons per ton of pig iron. History of Development of the Industry The history of the local utilization of slag as an industry probably starts with the Birmingharii Slag Cement Co. This company was

Jan 1, 1938