Search Documents

By Shiou-Chuan Sun

THE presence of an excessive amount of tough froth in the flotation of minerals, particularly coals, may create trouble in dewatering, filtering, and handling. Froth is also a nuisance in many chemical industries.' This paper presents a study on the destruction of extremely tough froths with intense high-frequency sound. The data indicate that sound waves can be employed for continuous atandsoundwavescan instantaneous defrothing. A powerful high-frequency siren was used in obtaining the data. Also tested was an ultrasonorator of the crystal type with a frequency range of 400, 700, 1000, and 1500 kc per sec and a maximum power output from its amplifier of 198 w. The results, not presented, indicate that as now designed this machine is not suitable for defrothing. Although the sound generators of the magnetostriction type2,3 and of the electromagnetic type'.' were not available, it is beelectromagneticlieved they are capable of producing the required sound intensity for defrothing. The use of ultrasonics for defrothing was suggested by Ross and McBain1 in 1944. Ramsey8 reported in 1948 that E. H. Rose mentioned a supersonic device that broke down flotation froth but with low capacity. The writer has not been able to find any published literature containing practical experiments. Theoretical Considerations The mechanism of defrothing by sound is attributed to the periodically collapsing force of the propagated sound waves and the induced resonant vibration of the bubbles. The collapse of froth is further facilitated by the sonic wind and the heat of the siren. Sound waves can exert a radiation pressure'," against any obstacle upon which they impinge. When a froth surface is subjected to the periodic puncturing of sound waves, the bubbles are broken. According to Rayleigh9 and Bergmann,12 the radiation pressure of sound, P, in dynes per sq cm is given as: P = 1/2 (r+1)i/v where r is the ratio of the specific heats of the medium through which sound is traveling and is equal to 1 on the basis of Boyle's law; i is the sound intensity in ergs per sec per sq cm, and v is the sound velocity in cm per sec. In this case, the accuracy of the formula is only approximate, because a perfect reflection can hardly result from a column of froth. In addition to the radiation pressure, the propagated sound waves cause the bubbles of the froth to have a resonant vibration.'" he vibratory motion of the bubbles causes collision and coalescence, thereby weakening if not breaking the bubble walls. Sonic wind and heat were also generated." The sonic wind can exert pressure on the froth surface, and the heat can evaporate the moisture content of the bubble walls as well as expand the enclosed air. Apparatus The defrothing apparatus, shown in Figs. 1 and 2, consists of a powerful high-frequency siren, a glass or stainless steel beaker of 2-liter capacity with 12.4 cm diam and 17.1 cm height, and a metal reflector. The beaker was placed 2 in. above the top point of the siren. The metal reflector was adjusted to reflect and focus the generated sound waves into the central part of the beaker. Fig. 2 shows the crystal probe microphone used to measure the acoustic intensity and the mandler bacteriological filter employed to introduce compressed air into the beaker for frothing. The apparatus was enclosed in a soundproof cabinet equipped with a glass window. The siren, shown in Fig. 3, consists of a rotor that interrupts the flow of air through the orifices in a stator. The rotor, a 6-in. diam disk with 100 equally spaced slots, is driven by a 2/3 hp, Dumore W2 motor at 133 rps. The frequency of the siren can be varied from 3 to 34 kc. The maximum chamber pressure is about 2 atm, yielding acoustic outputs of approximately 2 kw at an efficiency of about 20 pct. The siren itself is relatively small and can be operated in any orientation. A detailed description of the siren has been given by Allen and Rudnick.11 Collapse of Froth To study the sequence of the collapse of froth, the glass beaker was partially filled with 920 cc water, 100 g of —150 mesh bituminous coal, 0.3 cc petroleum light oil, 0.2 cc pine oil and 1.54 cc Pyrene foam compound. This mineral pulp was agitated for 5 min and then aerated through a mandler filter until the empty space of the beaker, approximately 9 cm high, was filled completely with min-

Jan 1, 1952

By Harold B. Goldman, Don Reining

The sand and gravel industry is the largest nonfuel mineral industry in the nation. In 1981, the production of sand and gravel totaled 755 million tons valued at $2.3 billion. California, which leads the nation with more than 110 million tons, together with Alaska, Texas, Michigan, and Ohio, account for 36% of the total production in the nation (Table 1). In commercial usage, sand applies to rock or mineral fragments ranging in size from particles retained on a No. 200 sieve (0.074 mm openings) to those passing a No. 4 sieve (4.76 mm openings). Gravel consists of rock or mineral fragments larger than 4.76 mm, ranging up to 88.9 mm (3 ½ -in.) maximum size. The construction industry consumes 97% of the sand and gravel produced; the remainder is sand used for specialized products such as glass (see the chapter on "Silica and Silicon"). Utilization The building industry uses sand and gravel chiefly as aggregate in portland cement concrete, mortar, and plaster; the paving industry uses sand and gravel in both asphaltic mixtures and portland cement concrete. Aggregate is commonly designated as the inert fragmental material which is bound into a conglomerate mass by a cementing material such as portland cement, asphalt, or gypsum plaster. Portland Cement Concrete Aggregates Portland cement concrete consists of sand and gravel surrounded and held together by hardened portland cement paste. Concrete mixes commonly contain 15-20% water, 7-14% cement, and 66-78% aggregate. Sand and gravel used as concrete aggregate have to meet many requirements (Goldman, 1956). Premature deterioration of concrete has been traced in many instances to the use of unsuitable aggregates. Asphaltic Aggregate Asphaltic mixtures used predominantly for paving consist of combinations of sand, gravel, and mineral filler (material finer than 0.003 in.), uniformly coated and mixed with asphalt produced in the refining of petroleum. Except for the addition of mineral filler, sand and gravel used as asphaltic aggregate must meet the same general physical requirements as materials used for portland cement concrete aggregate. General Requirements of Aggregates Construction aggregate has many requirements that are difficult to meet if only unprocessed material from natural deposits is used. Suitable material is composed of clean, uncoated, properly shaped particles which are sound and durable. Soundness and durability are terms used to denote the ability of aggre- [ ]

Jan 1, 1983

The following is an incomplete list of members and guests who called at Institute headquarters between Nov. 10 and Dec. 10, 1917. Harlan H. Bradt, Duluth, Minn. Lt. Geo. H. Morgan. Albert Burch, San Francisco, Cal. F. W. Osborn, Ajo, Ariz. J. A. Daniel, Institute of Mining & Metal- J. C. Ray, 2d Lt., 0. M. C., N. A. lurgy, London. A. E. Ring, Creede, Colo. Martin Fishback, Benson, Ariz. Geo. B. Rodgers, Dobbs Ferry, N. Y. E. L. Foucar, San Francisco, Cal. Forest Rutherford, Pueblo, Colo. I. A. L. Henderson, Institute of Mining & J. G. Scrugham, Reno, Nev. Metallurgy, London. A. F. Shurick, Forest Hills, L. I., N. Y. Jerome A. Hilbert, Santa Monica, Cal. Arthur C. Spencer, Washington, D. C. B. B. Hood, Chrome, N. J. Robert C. Sticht, Mt. Lyell, Tasmania. J. C. Hoyt, Jerome, Ariz. A. Perry Thompson, San Francisco, Cal. A. F. Kennedy, Duluth, Minn. J. B. Tyrrell, Toronto, Canada. Paul S. King, Wilmington, Del. Thor. Warner, Phoenix, Ariz. Alfred C. Levis, Golden, Colo. S. F. Wellman, Cleveland, 0. A. F. Lucas, Washington, D. C. Gardner F. Williams, San Francisco, Cal. B. E. McKechnie, Sharon, Pa. W. G. Woolf, Salt Lake City, Utah.' A. N. Mackay, Barranquilla, Colombia. C. W. Merrill, San Francisco, Cal. P. G. Beckett expects to be located in New York for some time, and may be addressed care of the Phelps, Dodge Corporation at 99 John Street. Corey C. Brayton and E. R. Richards have temporarily closed their San Francisco offices in order to give more time to their operations at Midvale, Utah.

Jan 1, 1918

By Wm. Reuben Webster

BRASS is an alloy of copper and zinc. The brasses (using this term to denote all useful proportions of the two constituents) are the most valuable and widely employed of all [ ] nonferrous alloys, because of their high resistance to ordinary corrosive agencies and the very wide range of properties that may be imparted to them by variations in the proportions of the constituents and by variations in mechanical treatment and heat-treatment. Fig. I shows the normal physical properties, as determined by standard tensile tests, of the series when in the annealed condition. Fig. 2 shows the effect of varying amounts of cold-working on an almost pure brass containing 70 per cent copper and 30 per cent zinc. Fig. 3 shows the effect of annealing at various temperatures on the same alloy. This effect is somewhat modi [ ] fled by the degree of cold-working to which a brass has been subjected, as shown by Fig. 4. A fourth test, which is empirical, has been found useful because of its simplicity -the hot hammer test. Samples Y2 in. in diameter and ¾ in. long are placed in a suitable furnace. These are withdrawn one at a time at successively higher tempera¬tures and are subjected to the blow of a drop hammer weighing 50 lb. with a drop of 4 ft. The percentages of' reduction in length of the cylinders are plotted against temperatures and give a comparative measure of plasticity at different temperatures. The results of this test on several

Jan 1, 1942

By W. L. Phillips

Single crystals of aluminum, brass, and copper oriented for (100) and (110) slip were extended at 25°, 400°, and 600°C in simple shear. Aluminum specimens oriented for nonoctahedral slip began to shear at a higher critical resolved shear stress than specimens oriented for octahedral slip. Parabolic stress-strain curves were obtained from zero strain. The initial rate of parabolic hardening was lower for specimens sheared on the (100) plane in a close-packed direction <110>, than for specimens sheared in a nonclose-packed direction <100>. metallographic evidence, however, showed that all slip traces could be explained in terms of (111) <100> slip. All attempts to cause nonoctahedral slip in copper and 70-30 a-brass single crystals were unsuccessful. Instead of shearing, the crystals bent, allowing {111} type planes to come into action. NONOCTAHEDRAL slip in aluminum has been reported under three different conditions: first, as the main mode of slip in tension experiments at elevated temperatures;&apos;-&apos; second, as the main mode of slip in direct shear experiments at room temperat~re; and third, as a minor mode of deformation, i.e., as cross-slip, in tension, shear, and bicrystal experiments at room and elevated temperatures."-l2 However, as far as the author knows, nonoctahedral slip has not been reported in either copper or 70-30 a-brass. The present study was undertaken to determine whether nonoctahedral slip could be obtained in aluminum, brass, or copper at room or elevated temperatures when the shear stress was approximately constant over the cross-section, a maximum at the center, or a maximum at the surface. EXPERIMENTAL PROCEDURE A detailed description of the crystal preparation and shearing apparatus has been given previo~sly. Cylindrical crystals 1/2 in. in diam and 8 in. long were grown from the melt in a temperature-gradient furnace. The aluminum contained 0.001 pct Zn, 0.001 pct S, and 0.001 pct Fe; the 70-30 brass contained 0.015 pct Pb, 0.001 pct Fe, 0.01 pct Ni, 0.02 pct Sn, and 0.005 pct Se; the copper was certified OFHC of 99.98 pct purity. All samples were electropolished prior to testing. The shear apparatus was a modified Bausch type. The strain sensitivity was 4 x lob4 Load was applied by clamping the rods attached to the shear plates in an Instron tensile machine. The rate of loading was 0.02 in. per min. In all cases a 1/8-in. gage length was used. For the tests performed at 400° and 600°C the shear plates, collars, and rods were made of stainless steel. These elevated-temperature tests were performed in an argon atmosphere. A) Aluminum at Room Temperature. Values of a and ß for the various slip planes and slip directions investigated are shown in Table I where a is the complement of the angle between the specimen axis and the slip direction, and ß is the angle between the specimen axis and the normal to the shear plane. The shear stress is a function of a (assuming ß - 0);10 when a is less than 27 deg, the shear stress on the slip plane for which the specimen is oriented has a maximum at the center of the crystal; at a = 27 deg the shear stress is constant across the slip plane; for a greater than 27 deg the shear stress is a minimum at the center. Fig. 1 shows the stress-strain curves for specimens cut from crystals 1, 2, and 5, which were sheared on the (010) plane in the [loll direction at room temperature. These three crystals have shear-stress distributions corresponding to the three dif-

Jan 1, 1962

[59H1-Water Law and Its Significance to the Mining Industry by Wells A Hutchins 59H2-Relation of Land Subsidence to Groundwater Withdrawals in the Upper Gulf Coast Region, Texas by Leonard A Wood and A G Winslow 59F3-Hydraulic Mining of Gilsonite and Its Application to Coal Mining by J H Baker 59H4-Recovery of Phosphates by In Situ Fluid Mining by Sylvain J Pirson 59F5-Coal Cleaning Plant Design for Minimum Operating Labor by Wm M Bertholf and John D Price 59F6-Coke Combustibility A Neglected Characteristic by J D Price 59B7-Union Carbide&apos;s Uranium Operation at Maybell, Colorado by K W Lentz and F T Temple 59H8-A Rapid Method for Estimating Alumina in Feldspathic Sands by Hugh H Bein 59H9-Water Laws as Related to Dredging in Idaho by Robert A Lothrop, Richard B Porter, and Robert P Porter 58B19-Separation and Washing of Alumina Process Residue by Morton Handelman 59B11-Feed Preparation and Froth Modification for Fatty Acid Flotation by Carl C Martin and Burt C Mariacher 59B12-Design Requirements for Tailing Disposal in the Southwest by E Vern Given 59B13-Semi-Dome Shaped Buildings for Bulk Storage by Edward E Ives and William L Payne]

Jan 1, 1961

By G. L. Smit

The Buffelsfontein Gold Mining Company is situated in the Klerksdorp district of the Province of the Transvaal in the Republic of South Africa, approximately 100 miles west of Johannesburg. Gold production commenced in January 1957 and Uranium treatment of residue slimes as a by-product started in July 1957. The mining property is 5435 mining claims in extent, the equivalent of 7988 acres or 12.5 sq miles. The mine was initially exploited by the Pioneer Twin Shaft System, consisting of a 26-ft diam down-cast shaft and a 22 ft-diam up-cast shaft, sunk in the north-west area of the mine to cater for the hoisting and ventilation requirements for a milling rate of 150,000 tons per month. To exploit the Eastern zone of the property and assist in increasing production to 200,000 tons milled per month, it was decided to sink a further Twin Shaft System consisting of a 28-ft diam downcast shaft and a ventilation up-cast shaft -22-ft in diam, both monolithic concrete lined — 200 ft apart and 5300 ft deep. This paper deals with the sinking and commissioning of these Eastern Twin Shafts. This was achieved by one sinking crew within a period of 20 months. A) PLANNING 1) Siting: The Eastern Shaft System was sited in the north-east area of the property, 12,000 ft east on strike from the Pioneer System. (Fig. 1). Initially the system was sunk to the 5300 ft elevation to conform with the original Pioneer Shaft System. On completion a sub-vertical main shaft will be sunk to the 8000 ft elevation in the immediate vicinity, and subsequently the surface ventilation shaft will be deepened to this elevation by raising from level to level and sliping to full size. The exact positions of the shafts were chosen after: a) underground development had located certain known water bearing zones, and b) geophysical and topographical surveys had been carried out. The shafts passed through the following geological succession: Surface to 4430 ft - Dolomites of the Transvaal System 4430 to 4470 ft - Quartzites and conglomerates of the Black Reef Series of the Transvaal System. 4470 to 4470 ft - Diabasic Lava of the Venters-dorp System (Ventersdorp Contact Reef at base). 4470 to 5250 ft - Quartzites of the Elsburg Series of the Upper Witwaters-rand System. The shafts were sited to ensure that the least possible water would be encountered during sinking, and this contributed to the rapid rate of sinking. 2) Duties: a) The 22-ft diam ventilation shaft was designed to up-cast 1,400,000 cfm of air (0.060 density) against a resistance of 22 in. water gauge. b) The main shaft was designed to handle 160,000 tons hoisted per month as well as the men, material and down-cast ventilation to serve this tonnage. The 284 diam main shaft is equipped with streamlined buntons spaced at 15 ft centers set in pockets which were left during sinking. There are six compartments, four of which are sewed by two dual purpose hoists, hoisting either, twedeck man cages or 13-ton bottom discharge skips. The other two compartments are served by a single purpose winder hoisting double deck cages accommodating 60 men per deck. (Fig. 2). 3) Timing: Permanent equipment was ordered well in advance to insure continuity in the operation. Development underground reached the shaft positions before the start of sinking operations. From this development, boreholes were drilled into shaft positions to drain off water in the vicinity of the shafts. To ensure complete co-ordination of effort, all relevant data, as well as the allocation of responsibility, were made known to all persons and departments concerned. 4) Models: The extensive use of scale models during the preliminary planning stages proved most useful in deciding on design such as buntons, bunton pockets and guide cleats, and complex layouts concerning loading, spillage and pumping arrangements. (Fig. 3). These models also proved invaluable in determining the walling routine. Normal working conditions could

Jan 1, 1964

By Russell B. Cornell, William B. Plank

AT the close of the academic year 1940-&apos;41 the largest number of students ever recorded received their first or bachelor degree in the mineral technology schools of the United States. The total of men thus prepared to enter their professional careers in the mineral industries was 1601, a number nearly 12 per cent larger than two years ago and nearly 75 per cent larger than four years ago. Notwithstanding this increase in the number of graduates and as had been predicted in the preliminary report in February, there was a slight decrease in the total student population of the schools in both the United States and Canada. During the college year 1940-&apos;41, 9133 students were enrolled in the 54 schools of the United States and 764 in six of the seven schools of Canada.

Jan 1, 1941

By Oliver Bowles

STRIKING new developments in the field of industrial minerals include the employment of lime, salt, coal, and air for the manufacture of stockings, and the substitution of paper for granite and marble in making tombstones. Certain minerals that have heretofore been regarded as valueless except as museum or laboratory specimens, are now being applied commercially. Serpentine, in forms neither fibrous nor ornamental, massive topaz, pinite, and zoisite are examples. For certain other minerals, notably pyrophyllite, bentonite, vermiculite, and sulphur, extension of established uses into new fields has occurred. Substitution takes a toll in many industries, but producers of industrial minerals as a class have gained more than they have lost in recent years. Encouraging progress has been made in developing at long last a suitable substitute for certain of the uses of mica, the only industrial mineral on the strategic list of commodities established by the War. and Navy Munitions Board. Some of the more important developments in process, equipment, and use .that have come

Jan 1, 1940

By E. R. Gilbert

Klopp et al. have reported data on tensile and creep properties of are-melted and electron-beam-melted tungsten. We would like to point out some similarities between their creep results and ours on are-melted and powder-metallurgy tungstenand offer some alternate interpretations of the data which lead to different rate-controlling mechanisms. Klopp et al. observed extensive transient creep in the 2250" to 3500°F temperature range where the acthetivation energy is 106,400 ± 3300 cal mole-1. They suggest cross slip as the possible rate-controlling mechanism since "cross slip may occur only by the movement of screw dislocations, and not edge dislocations, thus allowing only partial recovery of the strain hardening and resulting in a continuously decreasing creep rate, characteristic of transient creep.&apos;&apos; Our tests on are-melted tungsten and powder-metallurgy tungsten displayed an extensive transient creep stage in the same temperature range but they also displayed a steady-state creep stage. The stress levels and strain rates of the two investigations, 1.4 to 7 kg mm-2 and 10-7 to 10-4 sec-1 for that of Klopp et al. and 4.5 to 10 kg mm-2 and 10-8 to 10-4 sec-1 for those of Gilbert et al., are overlapping. The activation energy for creep of our powder-metallurgy tungsten is 105,000 cal mole-1. This close agreement with the value found by Klopp et al. suggests that the same mechanism may be common to both types of materials. It may be possible to gain some additional insight into the rate-controlling mechanism by applying the analysis made by conrad22 in terms of the activation volume. The value for the activation volume depends upon the dislocation mechanism and may be used to help differentiate between various dislocation mechanisms. The activation volume for cross slip is 10 to 100 b3. Values determined from our data were 130 to 220 b3 which are in better agreement with the range of 102 to 104 b3 for nonconservative motion of jogs. Values determined from data of Klopp et al. are 240 to 1040 b3. We suggest that the rate-controlling mechanism for creep in this temperature range may be nonconservative motion of jogs assisted by enhanced diffusion along grain boundaries or dislocations. This model requires an activation energy lower than that for self-diffusion as is observed. If this is the controlling mechanism, a higher activation energy which is closer to that for self-diffusion might be expected for tests conducted on specimens with reduced grain boundary area, i.e., larger grain size. In support of this premise we have conducted tests on speci- mens having one to three grains per cross section for which a higher activation energy of 130,000 cal mole-1 was observed. Also, in agreement with results of Klopp et al., a faster creep rate resulted from the increased grain size and probable decreased dislocation density. Further argument against the cross slip mechanism is based on the constant activation energy we obsserved over the range of 5.0 to 10 kg mm-2,21 whereas the activation energy for cross slip displays a significant stress dependence.23 In addition to this, the powe on the stress term for the strain-rate dependence appears too high for cross slip. The values for tungsten fall in the range of 4.5 to 7 (Klopp et al. and Ref. 21) whereas values of approximately 2 are observed in creep by cross slip for hep metals.24 At temperatures from 3300° to 4000°F, Klopp et al. observed an activation energy of 141,000 ± 4000 cal mole-&apos; which is less than that for self-diffusion, 153,000 cal mole-1, 25 and less than that reported for high-temperature creep of powder-metallurgy tungsten by Green:&apos; 160,000 cal mole-1. Klopp et al. suggested that recovery of strain hardening by dislocation climb is the rate-controlling mechanism in this temperature region. Actually an activation energy larger than that for self-diffusion is predicted by this model if the temperature dependence of the elastic modulus27 is taken into consideration. Klopp et al. attributed this lack of correlation to the compositional differences between powder-metallurgy tungsten used by Green and their own arc- and EB-melted tungsten. It is our position that the value of 141,000 ± 4000 cal mole-&apos; represents a transitional value between the higher and lower activation energies and does not represent a discrete mechanism of deformation. If the tests had been extended to higher temperatures the higher value of activation energy would have been observed as has been demonstrated by both our analy sis&apos;&apos; of isothermal test data by GE-NMPO28 and differential temperature tests28 on are-melted tungsten. The activation energies determined (170,000 and 160,000 cal mole-1) were greater than that for self-diffusion and are in better agreement with the value found by Green. The model of dislocation climb is associated with ; activation volume of 1 b3 according to Conrad.22 The activation volume calculated for the creep data of fou independent investigators in the temperature range where the activation energy for creep is near that for self-diffusion (Klopp et al. and Refs. 26, 28, and 30) is 110 to 2800 b3 and is in the range suggested for nonconservative motion of jogs. In the case of tungsten this mechanism may be preferred over that of dislocation climb. Sincere appreciation is expressed to Messrs. J. E. Flinn and F. L. Yaggee for the helpful discussions and suggestions in the preparation of this communication.

Jan 1, 1967

"WELFARE…Welfare endeavor in connection with both the metal and the coal mines of Utah has shown gratifying progress during recent years and both the operators and their employees are deserving of much credit for the efforts put forth to better living, working, educational and receational conditions in most of the mining camps of the state.In the older metal mining camps of Utah, where the towns are incorporated and independent of the mining properties operating in the vicinity, less opportunity is pre¬sented for the companies to exercise efforts looking towards improved welfare conditions than is the case of camps located on company ground and under the full control of operators.Even in such camps, however, as illustrated in Bingham, the companies can do much to better welfare conditions. In this camp the Utah Copper Company has spent $800,000 since 1 920 in the erection of modern brick cottages, apartment houses and the Gemmell Memorial Club. The cottages and apartments have every convenience to be found in up-to-date city homes. The Gemmell Memorial Club, erected and equipped at a cost of $1 75,000, was provided by the company for the benefit of the Utah Copper Company employees living in the canyon and has been made the recreational center for the camp."

Jan 1, 1925

By F. G. Tahmoush, N. J. Grant, E. P. Abrahamson

The effect of grain size on the brittle -ductile transition temperature of pure iron and three dilute Fe-W alloys has been investigated by slow bend tests. The brittle-ductile transition temperature for pure iron increased with increasing grain sizes from 8000 to 500 grains per sq mm where the transition temperature then decreased with further increase in grain size. The dilute additions of tungsten lowered the transition temperature for fine grain sizes, suppressed a reversal of the curve in the coarse grained portion, and raised the transition temperature for this region. The frequency of twin occurrence increased with increasing grain size and decreasing temperature. The object of the present investigation was to re-examine the effect of grain size on the brittle -ductile transition of pure iron and several dilute Fe-W alloys. Current literature normally presents a simple relationship between grain size and the brittle-ductile transition temperature, namely, that the transition temperature increases with increasing grain size. Heslop and etch&apos; have studied the transition temperature of mild steel by V-notch Charpy impact tests for the grain size range between 200 and 6000 grains per sq mm. The result was a linear plot of In 1-1/2 vs brittle-ductile transition temperature, where 1 is the grain diameter. Recent experiments by sipos2 revealed the possibility of a reversal in the slope of the grain size vs transition temperature plot for pure iron; however, his investigation was limited in scope, and the data obtained were insufficient to permit a definitive curve. The present investigation was undertaken in an effort to confirm or extend the grain size effect observed in iron by Sipos. PROCEDURE All alloys were vacuum induction melted, using 99.95 pct Fe containing 0.03 pct 0 and 0.004 pct C. Four ingots were made, ranging from pure iron to iron with 0.035 pct W. The chemical composition of each alloy, after processing, is given in Table I. The four alloys were prepared as 45 lb heats and cast into 4 in. diam by 16 in. molds. They were then extruded into 3/4 in. rods at 1800oF. Specimens for chemical analysis, taken from various positions along the rods, revealed no variation in tungsten content along the length. The extruded rods were reduced to 0.156 in. diam stock by a series of cold swaging operations involving intermediate vacuum annealing treatments. This procedure yielded a final cold reduction in area ranging from 10 to 90 pct. The swaged rods were chemically cleaned, cold pressed to a cross section of 0.10 by 0.18 by 1.0 in. long (2.54 by 4.73 by 25 mm). The specimens were wrapped in iron foil and vacuum sealed (10-4 mm Hg) in quartz. Various heat treatments at temperatures from 700" to 1300oC were utilized to produce grain sizes from 8000 to 1 grain per sq mm. Grain sizes were determined by measuring the average area of grains in a polished section. In specimens with grain size greater than 20 grains per sq mm, the total number of grains in the cross section was counted and then divided by the area to yield grains per sq mm. Grain size was measured both for longitudinal and transverse cross sections. The average of the two measurements was plotted vs transition temperature. An Instron Table Model testing machine was used to determine the transition temperature of specimens tested in three point horizontal bending. The specimen was supported by two 1/4 in. dowels one in. apart. Bending was accomplished with a push rod, the end of which had an 1/8 in. radius. The head speed was 50 in. per min. Temperatures were established through the use

Jan 1, 1963

By Walter E. Hopper

The Caddo oil-field, shown in Fig. 1, is located in Caddo parish, northwestern Louisiana. The known producing territory of oil is covered by townships 19 N, 20 N, 21 N, 22 N, and ranges 15 and 16 W., shown in Fig. 2. The center of the field may be taken as Oil City, 24 miles north of Shreveport, on the Kansas City Southern railway. Shreveport is the second largest city in the State, and is the connecting point of five railroad-lines. Drilling at the present time, however, is going on all over northern Louisiana, especially in Caddo and the neighboring parishes. During the winter of 1908-09 I spent &apos;four months in the Caddo field, under the direction of the Louisiana Geological Survey and the U. S. Geological Survey. II. History and Development. Natural gas escaping at the surface is found at numerous places in northwestern Louisiana. At Shreveport, the plant of the Shreveport Ice & Refrigerating Co. has been lighted by natural gas for 20 years. The well was drilled for water, but was abandoned on account of the gas. A test well, put down in 1905 near the western limits of Shreveport, was driven to 1,650 ft., and encountered indications of gas and oil at various depths, but did not succeed in finding enough to be profitable. Attention was first attracted to the Caddo field in 1895 by indications in water-wells from 40 to 60 ft. deep, in which the pressure of natural gas was noticeable. This indication of gas in a shallow well led to the drilling of the first well in the Caddo field, the old Savage Brothers & Morricell, or the Caddo Lake Oil and Pipe Line No. 1. The rig for this well was erected in May, 1904, and drilling began in June, 1904. The well was bailed Mar. 23, 1905, with a small amount of oil. It was deepened July, 1905, and converted into a "gasser" Jan. 3, 1906. It was abandoned January, 1907. In consequence of the finding of oil in the Savage well, drilling-operations were pushed with energy; and in April, 1905,

Jan 1, 1912

By R. Grierson, R. N. Parkins

The m.echanica1 properties, at high lzomologous temperatures, of the intermetallic compounds InzBi and Mg17A112 were measured as a .function of temperature, applied strain rate, previous thermal and mechanical history, and composition. Mgl,Al12 was investigated ilz compression, whereas Zn,Bi was investigated in tension. A decrease inflow stress with increasing strain was observed jor both alloys. The results obtained are discussed in terms of the dislocation-multiplication processes in these materials. MANY intermetallic compounds are reported to undergo a brittle-ductile transition at high homologous temperatures.&apos; There is evidence in the literature that some of these compounds exhibit a large yield drop when plastically deformed.&apos;j3 Both of these forms of behavior are shown by the covalent elements germanium and silicon4,5 and also by certain ionic compounds.8 The present work is a study of the deformation, at high homologous temperatures (>2/3 Tm), of two intermetallic compounds, In2Bi and Mg17Al12. InzBi has a disordered hexagonal structure7 (c/a = 0.598) and a solubility range of 32.3 — 33.2 at. pct Bi.8 It has a melting range from 72° to 89°C. Mg17Al12 has an ordered bcc (A12 type)7 structure and exists over the range 50 to 60 at. pct Mg8 with a melting range from 437° to 462°C. We have been unable to find any reference to previous investigations of the mechanical properties of BiIn,. Novikovg has reported that cast samples of Mg17A112 show ductility, when bend-tested, at temperatures above 380°C. EXPERIMENTAL Ingots of In2Bi and Mg17Al12 were melted under an argon atmosphere and cast, in situ, in a graphite crucible. The materials used were of 99.99 pct purity. The alloys prepared contained 66.9 at. pct In in the case of In2Bi and 58.4 at. pct Mg in the case of m17A112. The ingots were homogenized and then extruded. Two-in.-diam Mg17Al12 ingots were extruded at 375°C to give 3/8-in.-diam rod. The rate of formation of this rod was 0.25 in. per min. One-in.-diam InzBi ingots were extruded at 20°C, using a rate of 1 in. per min, to give 1/8-in.-diam rod. In both cases the extruded rod had a recrystal- lized, fine-grain, structure. (For Mg17Al12, d = 11.2 µ; for BiIn2, d = 22 µ.) Mechanical-property determinations were made in a hard-beam machine, in tension in the case of In2Bi and in compression with Mgl7Al12. The tensile tests were on specimens having a gage length of 1.1/2 in. and a diameter of 1/8 in. The compression tests on Ml7A112 were on specimens of 3/8 in. diam by 3/8 in. high and the ends were coated with poly-tetrafluorethylene to minimize friction. RESULTS In2Bi. Fig. 1 shows, particularly at the higher applied strain rates, that In2Bi exhibits a marked yield drop as the deformation increases to about 2 pct, after which the material shows neither hardening nor softening up to 15 pct strain. The magnitude of the yield drop, the stress in the region of flow under constant stress (the stress plateau), and the 0.5 pct proof stress were all dependent upon the applied strain rate according to an expression of the form

Jan 1, 1965

By R. R. French

Investigations were conducted by the lndiana Geological Survey for some dry methods of bene-ficiating low-grade gypsum ore. Seventy-two batch and continuous flow tests were performed with a roller mill, rod mill, pebble mill, electronic color sorter, electrostatic separator, and an air separator. Approximately 650 size analyses and 550 chemical analyses were performed during the investigation. Batch samples were tested by the Survey, and most of the continuous flow tests were handled by com-mercial laboratories. INTRODUCTION Although many companies producing gypsum have been interested in dry beneficiation, very little information has been published in the past. One of the most comprehensive investigations was reported by the Canadian Department of Mines.5 Other reports of interest have been published by the Canadian Department of Mines,&apos; the South Australian Department of Mines,2 and the U.S. Bureau of Mines.3 Some beneficiating practices, such as hand picking, selective mining, crushing and screening, milling, and air classifying, were already in use in the Canadian industry prior to MacPherson&apos;s investigations.5 MacPherson examined the effect of tabling, air separation, screening, flotation, electrostatic separation, calcining, washing, and various types of milling, in his efforts to eliminate dolomite, limestone, and small amounts of silica and clay from the gypsum ore. RAW MATERIAL Gypsum and anhydrite occur within the lower part of the St. Louis Limestone (Mississippian) in southwestern Indiana. Gypsum in single beds 10 or more ft thick occur at Shoals, Martin County; near Freedom, Owen County; near Bloomfield, Greene County; and in the Devonian strata of LaPorte County. Only the Shoals deposit has been exploited commercially. The western edge of the Shoals deposit is contaminated by a continuous bed of shale, about 1 1/2 to 2 ft thick, near the top of the evaporite and by thin continuous strata or irregular masses of carbonate rock. The low-grade material used in these investigations was obtained from the waste pile of the National Gypsum Co.&apos;s plant at Shoals. The waste ore averaged about 67.4% gypsum and was contaminated by various amounts of shale, dolomite, and limestone. All the material had been previously crushed and screened to minus 1 1/4 to plus 3/8 in. X-ray analyses of powdered, sedimentated, gly-colated, and heat-treated samples of the shale showed that it was composed of slightly structurally disordered illite, Fe-rich chlorite, and very finegrained disseminated silt. The clays and silt were partly cemented with carbonate material. Light-gray argillaceous limestone and gray or brown porous dolomite made up most of the carbonate rock contamination. Crushing Characteristics: The rate unweathered gypsum, carbonate rock, and shale reduce in size was determined by crushing handpicked samples in a rod mill and screening at minus 100 mesh (.0059 in.). Fig. 1 graphically represents the data. These data indicate that carbonate rock should be relatively easy to separate from gypsum, but that shale should be difficult to separate from gypsum by differential crushing. Controlled Samples: Eight rod mill tests of hand-picked samples of mixed gypsum and shale and mixed gypsum and carbonate rock were made. Sample weight and crushing weight were standardized, but the scalping screen size was varied from 3 to 10 mesh (.265 to .0787 in.) in order to obtain the optimum purity and recovery. The data obtained from the tests (see Table I) illustrate that the relatively hard carbonate rock allows appreciable beneficiation (13.6 to 18%), but the low strength gypsum and shale allows only minimal separation (3.1 to 7.5%).* Semi control led Samples: During the investigation considerable slaking of the shale was noted when the ore was subjected to alternate wetting and drying. As demonstrated in laboratory tests, as much as 76% shale can be removed by two cycles of wetting and drying in a 48-hour period with subsequent screening at .265 in. Five ore samples, stockpiled and weathered, were screened, rod-mill crushed and rescreened at .157 or .187 in. with excellent results (Table 11).

Jan 1, 1967

By Jay J. Burns

TWO zinc concentrating mills are operated by the St. Joseph Lead Co. in St. Lawrence County, N. Y. The Edwards mill is operating at present only sixteen hours a day treating 400 tons daily. The metallurgy at Edwards presents no unusual problems therefore this discussion is mainly limited to the metallurgy of the Balmat ore. The Balmat mill has a capacity of 1,250 tons per day and the operating crew consists of three shift bosses each with five millmen per shift. Two crusher operators work on each of two shifts and one cleanup man on day shift. The repair crew is made up of a foreman and three repairmen, one of the repairmen being capable of taking over any operating job in the mill from shift boss down. Each millman is capable of handling the next job in line and several men in the yard crew are broken into handling the start-off job in the mill so that temporary shortages of men do not cause extensive overtime. Sphalerite, pyrite, and galena, the principal ore minerals, occur in a gangue of calcite, dolomite, and silicates, especially diopside, plus tremo-

Jan 1, 1947

By William M. Baldwin

Jan 1, 1946

By William M. Baldwin

Jan 1, 1946

By G. K. Burgess

(New York Meeting, October, 1913.) 1. COOLING AND HEATING CURVES BY G. V. BURGESS AND J. J. CROWE. § 22. THE results published in Professor Howe&apos;s paper 10 of our determinations on the Ac3 and Ar3 points for a series of commercial carbon steels 11 containing manganese in varying proportion, represent the average temperatures found by taking several (4 or 5) heating and cooling curves. The accompanying curves, Figs. 6 and 7, are, for each steel, the first heating and cooling curves as obtained by&apos; the inverse-rate method of Osmond, using a cylindrical chronograph sensitive to -0.1 sec. for recording .time. Simultaneous observations were also taken by the differential method with a platinum neutral and plotted by Rosenhain&apos;s derived differential method and gave substantially the same results, the curves having sensibly the same contours in both cases.12. The observations were taken in vacuo on cylinders 5/8 by 1 in. in length bored to center with a 1/8-in. hole to receive porcelain insulated thereto-couple, and inclosed in an out- and in-glazed Berlin porcelain tube heated electrically by, platinum foil wound on the tube. The vacuum was usually better than 0.1 mm. The heating and cooling of the furnace was automatically controlled by a salt-water rheostat with shaped electrodes, giving a uniform rate of heating and cooling.

Jan 6, 1913

By R. A. Deju, R. B. Bhappu

The basic structural unit of all silicate minerals is a tetrahedron with a silicon atom at the center and four oxygen atoms at the corners. The oxygen-silicon distance is about 1.6 & and the oxygen-oxygen distance about 2.6 &. The different types of oxygen-silicon frameworks in the various silicates are based entirely on the combinations of the tetra-hedral oxygen-silicon groups through sharing of oxygen atoms. In recent years, infrared spectroscopy has permitted estimation of the ratio of the ionic character of the oxygen-silicon bond to be a few times that of the oxygen-carbon bond and the ratio of electro-negativity of the two bonds has also substantiated this finding. On this basis, it is generally accepted that the oxygen-silicon bond is the strongest one occurring in silicate minerals. As the oxygen-silicon ratio increases from quartz to the olivines, a greater percentage of the oxygen bonding power is available for bonding to cations other than silicon. Hence, with an increasing oxygen-silicon ratio, there is increasing oxygen-to-metal bonding. Upon the fracturing of a silicate mineral crystal, the oxygen-metal bond, which is almost entirely ionic in character, should break more easily than the stronger oxygen-silicon bond, resulting in a greater number of unsatisfied negative forces on the surface. If, then the mineral is immersed in a liquid containing hydrogen ions, these negative forces should tend to be neutralized by hydrogen ions from solution, resulting in a change of the pH of the solution. An increase in the degree of adsorption of hydrogen ions is to be expected as the oxygen-silicon ratio in the crystal structure increases. This study attempted to correlate the oxygen-silicon ratio for various representative silicate minerals to the adsorption of hydrogen ions. Experiments to determine the effect of surface area on this adsorption and to investigate the effect of surface iron were also conducted. It is believed that such studies of the surface properties of silicate minerals will supply pertinent information about their behavior in froth flotation systems. EXPERIMENTAL PROCEDURE Ion Exchange: Carefully selected, hand-picked samples of the minerals investigated were dry-crushed in a ceramic ball mill and sieved to obtain a minus 100 plus 200-mesh sample. The sized samples were then run through the electro-magnetic separator to remove any iron-bearing particles. A 10-g sample of each mineral was placed in 100 ml of freshly deionized water previously adjusted to a pH of 3.50 with HCl. The beaker containing the sample and the water was placed under a bell jar from which the air was displaced at once by nitrogen gas from a tank. All experiments were carried out in a nitrogen atmosphere. The sample and solution were stirred gently but continuously during the entire experiment, the stirring speed being kept about the same for all runs. Changes in pH were followed with a Beckman Zeromatic pH meter and recorded on a

Jan 1, 1967