Search Documents

By Leslie G. McMillion

A field project to develop and demonstrate a method for alleviating problems of highly mineralized ground water where they occur as isolated zones or pockets in fresh-water aquifers is being conducted in the Ogallala aquifer of eastern New Mexico by the Robert S. Kerr Water Research Center. Removal of contaminated water is by a large-capacity well and the pumped poor-quality water is used locally for secondary recovery of oil. Benefits of the operation are threefold in that the aquifer is being reclaimed for future fresh-water production, contaminated water is being used beneficially, and fresh water which otherwise would have been used for waterflooding is available for other purposes. Ground-water quality in the site has improved markedly after two years of operation. Use of water in the arid and semiarid Southwest has grown so rapidly that demands in many localities far exceed available supplies. In the High Plains region of New Mexico, Oklahoma, and Texas, the only large sources of water are underground reservoirs, being depleted at an alarming rate. In some parts of this region, the aquifers contain pockets of highly mineralized waters; and the mineralized waters in some of them have started spreading in response to the drawdown effects of pumping wells. The aquifers of this region are primarily composed of sand and gravel beds; any cleanup by natural processes will require many tens or even hundreds of years. Most of these pockets of highly mineralized water were caused by oil-field brines seeping downward from earthen disposal pits. Thousands of these pits were in use in the region until only a few years ago when they were prohibited by the oil regulatory agencies of the respective states. The resulting areas of poor quality water are serious enough to warrant much corrective attention. Correction will involve one or more of three approaches: 1) Restrict the pumping of fresh water in the zones where the drawdown of the pumping well will significantly influence the movement of the contaminant. 2) Remove the highly mineralized water entirely from the affected area. 3) Develop and pump the poor-quality water in such a manner that its movement is held in check, even though only a part of the contaminant is actually removed. The principal hurdle to overcome in applying methods 2 or 3 is financing of the operations, since there are very

Jan 1, 1972

By Rex W. Woods, Morris Muskat

A leastmsquare analysis procedure has been developed and applied for the study of the deviations in estimations of oil in place as given by the material-balance equations. The data used were those obtained from field observations on the Jones sand in the Schuler pool, Arkansas, and the Monroe dolomite in the Reed City pool, Michigan. Possible effects of water intrusion were taken into account by expressing the cumulative water influx in terms of various functions previously proposed in the literature. Formulas were developed and values calculated for the minimum deviations and minimal percentage deviations in the calculated volumes of oil in place from the average values, as could be obtained by suitable choice of the water encroachment and initial gas-cap volume parameters. The results show that the fluctuations in these calculated volumes are very insensitive to the values chosen for the rate of water intrusion and initial gas-cap volume, and hence cannot be safely used in discriminating between spurious values for these parameters and such as actually pertain to the producing reservoirs. Moreover, the exact form of the water-intrusion function seems to have but little effect on the fluctuations in the computed oil in place. Accordingly, it is concluded that the material-balance method does not of itself provide a satisfactory criterion for determining the basic physical unknowns of producing reservoirs or in making conclusive decisions regarding the production mechanism, unless independently established geological control data are available for eliminating unreasonable values for the reservoir parameters, even though they may still satisfy the material-balance formulas. If, however, from core or logging data the initial oil in place and the gas-cap volume can be established in advance, the material-balance formulas can be inverted to find the water intrusion. Moreover, by determining by such calculations the water-intrusion coefficient, the iuture production performance can then be predicted by the aid of the materiaI-balance formulas for specified operating conditions. This type of application may be of particular value in predicting the results of Pressure-maintenance operations. Introduction The evaluation of the forces acting upon an oil reservoir is a problem of considerable interest to the operator as an aid in determining the proper method of operation for the reservoir to obtain an optimum recovery of oil. In many pools, the nature and magnitude of the forces acting upon the reservoir remain unknown until an appreciable amount of ultimate recovery is obtained. To be of value to the operator, a reliable interpretation of reservoir performance should be available in the early life of the pool to permit an optimum plan of operation. Progress has been made in an understanding of reservoir behavior and the importance of the different factors involved. The material-balance method of estimating oil in place has been proposed as a tool in analyzing reservoir-performance problems.l The solution of such problems by this method ordinarily involves two or more unknown values relating to the nature of the reservoir, and the results

Jan 1, 1945

By Byron Pickard

AT MIDNIGHT of Sunday, Aug. 27, 1922, a fire was discovered in the main shaft of the Argonaut mine, Jackson, Cal. With the excep-tion of a shift boss and two skip tenders who escaped, the entire night shift of 47 men was trapped in the mine and entombed for 22 days, when the bodies were recovered. The entombed miners made a valiant but fruitless effort to save their lives. Rescue crews toiled strenu-ously day and night for 21 days to save the entombed men, only to find they had arrived too late. From the experiences of the entombed miners and of the rescue crews, valuable lessons may be learned to prevent future catastrophes.

Jan 11, 1922

By Keith G. Kirk, Lawrence E. Welborn, Patrick A. Ley

Over the past two years the Office of Surface Mining in conjunction with Energy & Minerals Technology Assessment, ENCORE Systems Inc., and Boeing Computer Services has developed the Economic Coal and Ore Reserve Estimation (ENCORE) Coal Seam Modeling System. This system is being used by OSM, certain states, and industry for mine planning and mine plan permit review. The ENCORE system enables the mining engineer to start at the reserve estimation stage of surface mine planning and continue through the entire mine planning process and into the permit preparation process. The ENCORE system enables the state and federal regulatory authorities to assess a given mining and reclamation plan permit application in a rapid and efficient manner and greatly speeds up the mine plan review and permitting process. The ENCORE system is user friendly and menu driven thereby permitting the engineer with minimal computer training to rapidly learn and utilize the system. Data are input both through digitized map files and bore hole information files and stored in a data base that is an integral part of the ENCORE system. The system performs reserve estimation through standard polygon methods, least square methods, and geostatistical (kriging) techniques. Geostatistical routines permit rapid evaluation of coal and overburden quality and quantity. System outputs include drill hole sumnary and resource summary reports, cross sections, isopach maps, structure contour maps, premining topography maps, postmining topography maps, and three-dimensional perspective views. The maps can be displayed on a high-resolution, color graphics terminal or generated by a high quality plotter and are suitable for direct inclusion in the mining and reclamation pl an permit application. This paper gives detailed examples of ENCORE'S use together with example outputs.

Jan 1, 1983

By Lee W. Abramson

INTRODUCTION The design of rock support for underground nuclear waste repositories requires consideration of special construction and operation requirements, and of the adverse environmental conditions in which some of the support is placed. While repository layouts resemble mines, design, construction and operation are subject to quality assurance and public scrutiny similar to what is experienced for nuclear power plants. Exploration, design, construction and operation go through phases of review and licensing by government agencies as repositories evolve. This paper discusses (1) the various stages of repository development; (2) the environment that supports must be de signed for; (3) the environmental effects on support materials; and (4) alternative types of repository rock support. Much of the information presented in this paper was derived from work conducted for Basalt Waste Isolation Project. Most of the information, however, would apply to other hard rock repositories. REPOSITORY DEVELOPMENT AND THE NEED FOR ROCK SUPPORT Repository development can be characterized by five general stages: exploration and design, excavation, waste emplacement, re trievability period, and backfilling. It is helpful to understand these phases of development to see where and when rock supports are required and how the design is verified. The description that follows is simplified. Details have been omitted, and future plans may not conform to this scenario.

Jan 1, 1984

By E. A. Anderson

In another paper' the writer has shown that the low permissible maximum fiber stress in a loaded zinc sheet demands a much closer support spacing than is used for steel. The limiting fiber stress in 13-gage (0.032 in.) sheets having a 1-in. depth of corrugation was found to be about 5000 lb. per sq. in. on a 37-in. span under a load of 40 Ib. per sq. ft. Corrugated steel sheets are commonly laid with spans varying from 48 to 60 in. In order to increase the span in 13-gage zinc to 54 in. (a common spacing) the metal must be capable of withstanding, under long-continued loading, a maximum fiber stress of about 10,000 lb. per sq. in. This is known to be impossible with unalloyed zinc. In this paper the writer describes a series of experiments leading up to the development of an alloy capable of safely sustaining this fiber stress. The effect of alloying on the slow creep of zinc was studied by means of static tensile tests, accurate determinations of apparent elastic limits and finally by means of loading tests on full-size roof sections. Two industrial buildings roofed with alloyed zinc sheets on spans involving fiber stresses in excess of 10,000 lb. per sq. in. have been under observation for over two years without signs of sagging. Experimental Work Two methods of increasing the maximum permissible fiber stress in zinc were considered. Cold rolling, which' increases the stiffness and tensile strength, was found to decrease the resistance to slow flow. Alloying, therefore, provided the only feasible means of obtaining the desired result, It was recognized that the improvement secured by the solid solution of natural impurities was insufficient. A series of alloys was outlined, therefore, in which a number of metals were added separately and together. The sheets rolled from these alloys were tested under

Jan 1, 1930

By James F. Howe

EveRy engineer and user of wire rope is desirous of information that will enable him to determine whether the performance of any particular piece of rope is satisfactory, and what conditions can be changed so as to increase the life of a rope. In most cases, it is far from easy to analyze the conditions of service and tell which is the greatest factor in determining the life of wire rope. If we start on a layout for an entirely new rope system, the task of making conditions satisfactory is simplified so far as the engineering details are concerned; but if the plant requiring wire rope is in operation, any change is likely to involve the expenditure of considerable money to replace and change over machinery that must be kept in constant operation, because a large monetary loss will result from a shutdown for even a few days. Often wire rope is kept operating under bad conditions, as the user thinks that it is cheaper and quicker to replace the rope than to make alterations in the hoisting machinery. A typical case is a metal mine operating in what is now almost the center of a large mining city, where it owns a few acres of mineral rights. It was expected that the shaft would go to a depth of 1000 ft. (305 m.), so a moderate-sized rope, about 1 1/4in. (31.7 mm.), was used on a 6-ft. drum with a 7-ft. head-frame sheave and rather short lead from drum to head sheave. This mine has gone deeper each year until it is now 2500 ft. deep and the rope speed has been increased from 1500 ft. per min. to over 3000 ft. The original rope just filled the drum in one layer, now it overwinds three layers. The original ropes were probably 6 X 19 crucible steel and lasted from 12 to 18 mo.; now, the highest grade plow steel is used, yet the average service is only about 6 mo. The cause is not hard to find. If the engineers had known at the outset what would be done with this hoist, the design would have been very different. Conditions at this mine, from a wire-rope standpoint, have gradually become worse and it is difficult to see how rope service on this hoist can be compared with the service of previous years with any fairness to the wire-

Jan 1, 1923

By James F. Howe

EveRy engineer and user of wire rope is desirous of information that will enable him to determine whether the performance of any particular piece of rope is satisfactory, and what conditions can be changed so as to increase the life of a rope. In most cases, it is far from easy to analyze the conditions of service and tell which is the greatest factor in determining the life of wire rope. If we start on a layout for an entirely new rope system, the task of making conditions satisfactory is simplified so far as the engineering details are concerned; but if the plant requiring wire rope is in operation, any change is likely to involve the expenditure of considerable money to replace and change over machinery that must be kept in constant operation, because a large monetary loss will result from a shutdown for even a few days. Often wire rope is kept operating under bad conditions, as the user thinks that it is cheaper and quicker to replace the rope than to make alterations in the hoisting machinery. A typical case is a metal mine operating in what is now almost the center of a large mining city, where it owns a few acres of mineral rights. It was expected that the shaft would go to a depth of 1000 ft. (305 m.), so a moderate-sized rope, about 1 1/4in. (31.7 mm.), was used on a 6-ft. drum with a 7-ft. head-frame sheave and rather short lead from drum to head sheave. This mine has gone deeper each year until it is now 2500 ft. deep and the rope speed has been increased from 1500 ft. per min. to over 3000 ft. The original rope just filled the drum in one layer, now it overwinds three layers. The original ropes were probably 6 X 19 crucible steel and lasted from 12 to 18 mo.; now, the highest grade plow steel is used, yet the average service is only about 6 mo. The cause is not hard to find. If the engineers had known at the outset what would be done with this hoist, the design would have been very different. Conditions at this mine, from a wire-rope standpoint, have gradually become worse and it is difficult to see how rope service on this hoist can be compared with the service of previous years with any fairness to the wire-

Jan 1, 1923

By W. R. Hibbard Jr., T. Michalak

THAT the amount of deformation and annealing time influences the recrystallization temperature of cold-rolled copper has been well established. Evidence that the recrystallization temperature can be affected by the deformation texture has been reported by Brick and Williamson,% ho found that copper straight-cold-rolled to 99 pct reduction to produce one deformation texture and copper cross-cold-rolled to 99 pct reduction to produce a second and different deformation texture correspondingly recrystallized at different temperatures to different textures. The purpose of the present work was to study more thoroughly the effect of the deformation texture on the recrystallization of cold-rolled copper. Experimental Procedure The copper used in this investigation was commercial OFHC copper (nominally 99.985 pct Cu) in the form of 0.500-in. plate. Qualitative spectro-graphic analysis showed only a slight trace of iron and a trace of silver. No analysis was performed to determine the exact content of the iron and silver,

Jan 1, 1958

By J. E. Campbell, G. D. Calkins, N. M. Ewbank, M. Pobereskin, A. Wesner

GRINDING for size reduction affects the economics of many processes and products. It is essential as the first step in many industrial processes and is also a finishing step for materials with properties depending on particle size, such as talc, cement, and silica sand. Intermediate and fine grinding are vital operations in the U. S. cement industry, which is producing more than 250 million bbl of cement per year.1 Wear of the grinding media is a large part of the grinding operation cost. Problems encountered in grinding cement are so complex that evaluation of efficiency and economy of grinding media is difficult.2 It has been especially difficult to evaluate the relative effectiveness of different types of balls because there are no good testing techniques.

Jan 12, 1957

By J. F. Wolff

EXPLORATION of Lake Superior iron ores is done principally by drilling. The soft iron ores are churn drilled and the harder ores are diamond drilled. In exploratory work in the harder formations, where the diamond drill is used, the sample comprises both core and cuttings. The care given in handling and preserving the core depends on the im-portance that may be attached to certain characteris-tic strata in different formations. The following instructions for the care of core samples are issued by the Oglebay Norton Co. for diamond drill work done for them on the Gogebic Range of Michigan: The driller shall be careful upon removing the core from the core-barrel to keep the core in exact order. Not only should the pieces of core be kept in exact relation to each other, but care should be used not to turn them end for end. Core should be placed in the core-box from left to right in each row. Each drill should be furnished with small, hinged cover core-boxes, and each drill should be well supplied with empty boxes. Core remaining at the drill when the drillers are not working should be locked up. The practice of picking sample pieces of core and carrying them away from the drill to be examined in better light, or shown to someone else, is unnecessary and prohibited. The reason for this is that these pieces are seldom returned to the core-boxes and valuable information or "markers" may be lost. If the inspector suspects that a critical point is reached in the drilling and he cannot determine at the drill, he should remove the entire core-box and see that the drill is immediately furnished with an empty core-box. It is customary to split the core longitudinally so that one-half may be ground to a pulp for analysis and the other half may be kept for future inspection. The core should be filed in permanent core-boxes, properly labelled, if the core is to be kept in exact order as taken from the core-barrel. Otherwise, it is often filed in tin boxes inn the way that sludge samples are filed. To obtain the average analysis, the core and cutting samples obtained in the same run are analyzed separately and the analyses are combined in the proper ratio.

Jan 9, 1922

By W. C. Lilliendahl, H. W. Highriter

The method developed and used in this laboratory for the production of metallic uranium of such purity that it is ductile and can be cold-worked to fine wire or thin sheet by rolling has already been described1. It consists, briefly, in the electrolysis of potassium uranous fluoride (KUF5) in a molten bath composed of equal parts of sodium and calcium chlorides. The bath is contained in a graphite crucible, electrically heated to about 775° C., the crucible serving as the anode for electrolysis. The uranium deposits in finely divided form mixed with salts upon a molybdenum cathode suspended axially in the crucible. Upon completion of the electrolysis the cathode is removed and cooled, the deposit broken and leached to remove salts. The metal powder is washed with water and dilute acetic acid and dried in vacuo to reduce oxidation. Suitable amounts are then prcssed into pellets and heated in vacuo by high-frequency induction, using a thoria crucible. The uranium melts and flows away from the pellet, leaving a shell, which is largely oxide. In general, this method produced a satisfactory metal, although at times tile uranium was not ductile. The investigations recorded here were made to find the cause of this embrittlement. It was known that the metal generally contained carbon, derived from disintegration of the graphitc crucible in which electrolysis is conducted, in amounts dependent upon the thoroughness of washing the metal powder. Accordingly, analyses of several samples, both ductile and brittle, were made by combustion and absorption of CO² in Ascarite, using air instead of oxygen to reduce the temperaturc and rate of oxidation. Several of these metals were made with special precautions to reduce carbon content. The results show no relationship between ductility and carbon content in the range investigated (Table 1). Microscopic examination of ductile and brittle metals disclosed the presence in the latter of an intergranular constituent, harder than the matrix and less easily oxidizable, which was absent from the ductile material. Rough estimates of the volume of the hard constituent

Jan 1, 1935

By W. C. Lilliendahl, H. W. Highriter

The method developed and used in this laboratory for the production of metallic uranium of such purity that it is ductile and can be cold-worked to fine wire or thin sheet by rolling has already been described1. It consists, briefly, in the electrolysis of potassium uranous fluoride (KUF5) in a molten bath composed of equal parts of sodium and calcium chlorides. The bath is contained in a graphite crucible, electrically heated to about 775° C., the crucible serving as the anode for electrolysis. The uranium deposits in finely divided form mixed with salts upon a molybdenum cathode suspended axially in the crucible. Upon completion of the electrolysis the cathode is removed and cooled, the deposit broken and leached to remove salts. The metal powder is washed with water and dilute acetic acid and dried in vacuo to reduce oxidation. Suitable amounts are then prcssed into pellets and heated in vacuo by high-frequency induction, using a thoria crucible. The uranium melts and flows away from the pellet, leaving a shell, which is largely oxide. In general, this method produced a satisfactory metal, although at times tile uranium was not ductile. The investigations recorded here were made to find the cause of this embrittlement. It was known that the metal generally contained carbon, derived from disintegration of the graphitc crucible in which electrolysis is conducted, in amounts dependent upon the thoroughness of washing the metal powder. Accordingly, analyses of several samples, both ductile and brittle, were made by combustion and absorption of CO² in Ascarite, using air instead of oxygen to reduce the temperaturc and rate of oxidation. Several of these metals were made with special precautions to reduce carbon content. The results show no relationship between ductility and carbon content in the range investigated (Table 1). Microscopic examination of ductile and brittle metals disclosed the presence in the latter of an intergranular constituent, harder than the matrix and less easily oxidizable, which was absent from the ductile material. Rough estimates of the volume of the hard constituent

Jan 1, 1935

By C. S. Trewin

ZINC, in its wrought form, is produced commercially in rolled strip, sheet, wire, rod and tubing. Wire has been made periodically, but due to the fact that slight drafts are necessary, the cost of production is greater than for the more common non-ferrous metals which are made into wire. Notwithstanding the cost, zinc wire has certain special uses for which it is particularly adaptable. Rod has been made both by rolling and extrusion, the product, however, has not indicated great commercial value. Tubing has been made from strip from time to time by forming a strip around a mandrel and either electrically or gas-welding a longitudinal joint. Recently a tube manufacturer has succeeded in making a fair quantity of this material. Its commercial adaptability is still to be determined but anyone who desires it can obtain quantities of the smaller sizes. Inasmuch as strip and sheet are commercially the most important, this paper will be devoted to these products. In the broader sense, zinc is not alloyed. That is, there are no combinations comparable to the various copper, aluminum and nickel alloys. It has been recognized,, for some time, that the lead and cadmium occurring with commercial zinc have some effect on its properties and such alloys as may be said to exist are those made from zincs containing varying amounts of lead and cadmium with a relatively low iron content. The foreign rolled zinc will analyze higher in lead than the domestic grades. A representative foreign analysis will run 1.1 per cent. lead, 0.07 per cent. cadmium and 0.02 per cent. iron. The American grades vary from zinc approximating high grade. and analyzing 0.08 per cent. lead, 0.002 per cent. cadmium and 0.015 per cent. iron, to the lower grades in which the lead will vary from 0.3 to 1.0 per cent., cadmium from 0.10 to 0.5 per cent. and the iron in the neighborhood of 0.02 percent.

Jan 1, 1927

By Frank J. Anderson

IN the cement region of the Lehigh Valley, a difference of 2 to 3 pct in CaCO3 can make or break a new quarry development, and experience of the Dragon Cement Co. has shown that values of calcium carbonate, as reported from churn drill samples, have been increased as much as 6 pct on the average when the same area was diamond drilled. This calcium carbonate increase consequently lowered the values for silica, iron, and alumina, and made these sections much more attractive. Since 1950, the Dragon Cement Co. Inc. has been engaged in extensive diamond drilling in the local limestone of the Northampton, Pa., region, known as the Jacksonburg formation, and in the Lebanon, Pa., region in the Annville limestone, both of Ordovician age.

Jan 12, 1954

By K. H. Nimerick, G. P. Laflin

Laboratory data and field tests indicate that substantial losses of valuable coal can be caused by wind erosion. Wind tunnel tests show the effects of wind velocity and particle sizing on the amount of coal lost while in transit. Different coals were evaluated to determine the variables associated with wind erosion. The erosion losses can be substantially reduced by using a binder, or crusting agent, to consolidate the surfaces of the coal into a solid mass which resists erosion. This not only reduces economic loss but minimizes pollution.

Jan 8, 1979

By F. E. Poulson

The discovery of two new fields, Van, in East Texas, and Darst Creek, in the Balcones fault zone, is the outstanding development in 1929. The first six months was one of the most inactive periods in the history of East Texas. Five of the interior salt domes, which had been so eagerly sought as a result of the Humble Oil & Refining Co.'s strike on the Boggy Creek dome in 1927, were drilled with discouraging results, and the Boggy Creek field itself had fallen far short of expectations. Kelsey, a structure of considerable magnitude and extent in Upshur County, was equally disappointing; the Amerada Petroleum Corpn.'s initial test on this structure was dry. The situation improved in the latter half of the year. On Oct. 13, 1929, the Pure Oil Co. discovered the Van field. This gained for East Texas a permanent place in point of future potential production. There was a similar reaction in the Balcones fault zone. The Salt Flats (Bruner) field, the important discovery of 1928, proved its rating as a second Luling, but on account of repeated failures to extend the productive zone, wildcatting during the first half of 1929 in the Luling district was dilatory. In July, however, Darst Creek, a third fault-line field of majori mportance producing from Edwards limestone (Lower Cretaceous), was discovered. Retarded as development in this field has been by various attempts at proration, interest in the Balcones fault zone fields centered on Darst Creek as the year 1929 drew to a close. Development in East Texas Fields Discovered during 1929 Van.—The discovery well, Jarman No. 1 of the Pure Oil Co., is near the town of Van in the southeastern part of Van Zandt County, Texas. It is 55 miles northeast of the Powell field in Navarro County and 45 miles west of north from the Boggy Creek field in Cherokee and Anderson counties. Early in 1927, the Van area was submitted to seismographic exploration and outlined as a large anticline, the apex of which seemed to be

Jan 1, 1930

By Donald L. Birkimer

GENERAL INTRODUCTION To paraphrase comments made by Black and Hoek(1) on the status of rock mechanics, the general methods of applied science related to rock mechanics are: a. Observe the phenomena of nature as they occur and, wherever possible, quantify the observations. b. Propound a model or theory to explain the phenomena observed. c. Test and develop the theory by further experimentation in the laboratory and in the field. d. Use the theory developed to predict behavior in similar or extended circumstances. e. Insure by measured experiment and observation that the predictions made are valid, or that deviations from the predicted behavior can be accounted for. f. Modify the theory and practice as necessary, and continue the process until more general laws can be formulated and applied, with a useful degree of confidence, to practical problems. This paper will present an infant concept. It will, in fact, propound a possibly useful theory to help explain commonly observed phenomena. It will test and develop the theory for a material similar in nature to some rocks. It will be used to predict behavior in the extended circumstances of a

Jan 1, 1971

By James M. Hodge

The Cumberland Gap extension of the Louisville and Nashville railroad, recently completed from Cumberland Gap to Norton, 71 miles, connects at the latter point with the Norfolk and Western, making a direct through line from Louisville to Norfolk. The whole of this connecting link skirts the southern boundary of the southwest Virginia coal region, but for the first 57 miles of its course it is separated from the coal by a mountain range (Cumberland mountain and its extension, Stone mountain), which bars entrance to the field from that direction, excepting at Pennington Gap, where access may he had to a small area only, which has not yet developed any very satisfactory coal. The railroad passes through the range at Big Stone Gap, and for the last 14 miles of its course to Norton is in direct contact with that part of the coal region known as the Big Stone Gap coal-field. By this road a western and southwestern outlet from the field is secured; the Clinch valley extension of the Norfolk and Western railroad gives exit eastward from Norton, and the South Atlantic and Ohio railroad, built through Big Stone Gap simultaneously with the L. & N. R. R., delivers the coal to points south and southeast. Besides these lines already built, an early connection with the East Tennessee, Virginia and Georgia railroad, via its Rogersville branch, is probable, and connections with the railroads of eastern Kentucky are projected. The Charleston, Cincinnati and Chicago railroad has already done some grading on one of the latter, but the rugged country intervening will prevent its construction till the demand for it becomes urgent. The coal-field embraces in Virginia about 120 square miles, to which should be added some 30 square miles in Kentucky, also tributary to Big Stone Gap, the whole of it underlaid by coal, probably of workable thickness, and much of it by two or more such beds. The determination of the boundaries of the field, however (except on the south, where Stone mountain forms a natural limit beyond which only a small, isolated tract of coal is found), is involved in much

Jan 1, 1893

By Donald Barton

THE purpose of this torsion balance survey and the quantitative calculations was to delimit the extension of the cap rock at the Hoskins Mound salt dome. The sulfur ore in the Gulf Coast sulfur-bearing salt domes occurs in the lime rock, which is the outer layer of the cap-rock mass, and also in the underlying gypsum zone. The status of the exploration and exploitation of the Hoskins Mound dome at the date of this survey is shown by Fig. 1. The mound had been covered by the very early prospect wells of the Mound Oil Co., and the later and more numerous prospect wells of The Texas Company. The Freeport Sulphur Co. was producing from the flank wells in the southwest quadrant. The limits of the cap were surmised to lie inside the centers of quad-rangles 4F, 3F, the center of the NE. ¼ of 2E, and the north line of 2D. That surmise was based partly on the data of Fig. 1 and partly on the position of the edge of the topographic mound. The management of the Freeport Sulphur Co. wished to block out the extent of its ore reserves with a minimum of expenditure. The management was informed by the writer that no geophysical method could map the presence or quantity of sulfur directly, or determine the presence and quantity of the lime-rock cap independently of the rest of the cap, but that a reasonable probability existed that the approximate position of the edge, the depth and the thickness of the cap-rock mass as a whole could be determined through quantitative calculations based on the data of a very careful torsion balance survey. Considerable lime rock would probably be present, of course, wherever much cap rock was present. This paper presents the data of the survey, our calculated prediction of the configuration of the cap rock, and the degree of confirmation by the subsequent drilling. The survey was made by the Geophysical Research Corporation, under the direction of the writer. The work of the calculations was done by Andrew Gilmour, then assistant to the writer.

Jan 1, 1936