Search Documents

By A. K. Sinha

The annual production and productivity of underground coal mines in recent years declined from 334 Mt (368 million st) and 14.5 t (16 st) per man per shift in 1969 to approximately 254 Mt (280 million st) and less than 8 t (9 st) per man per shift in 1977. Productivity is still hovering at about 7.25 t (8 st) per man per shift. According to US Bureau of Mines, the estimated US coal reserve is about 396 Gt (437 billion st), 68.65% of which is obtainable by underground mining methods. Approximately 153 Gt (169 billion st), or about 85.2% of the high Btu premium coking coal of the eastern US, would need to be extracted by underground mining methods. It is thus apparent that under- ground mining will continue to play a major role in total US coal production, which is expected to rapidly increase to about 1.1 Gt (1.2 billion st) by 1985, with about 606 Mt (668 million st) being contributed by underground mines. Production Potential of Continuous Mining The production potential of a continuous mining section depends primarily on the producing ability of the miner, transporting ability of the face haulage, and the matching of the two systems. The producing ability of the continuous miner depends on its actual cutting ability and the time available for cutting coal. The performance of 10 continuous miners operating in coal seams of various thicknesses were monitored in Pennsylvania and West Virginia, using continuous electrical power analyzers and time studies. The recordings on current and power strip charts yielded an accurate analysis of the cutting, trimming, and idle times of the machines on a full shift basis. Continuous miners of various models and sizes from 112-298 kW (150-400 hp) were monitored. Based on actual cutting time, the average cutting ability of the machines, as shown in [Fig. 1], ranged from

Jan 1, 1983

By R. S. Handy

The No. 2 unit of the West Mill of the Bunker Hill & Sullivan Mining & Concentrating Co., which went into commission Apr. 17, 1912, is structurally a twin of the No. 1 unit, which was started Nov. 9, 1909. Up to the point where the ore enters the concentrating-de-partment, it follows precisely the process described by G. Cae-tani in his article entitled, Milling of Lead-Silver Ores,' under the heading, Preparation of the Mill-Ore. The process from this point forward, in the No. 2 section, is outlined on the accompanying flow-sheet. In describing it I shall attempt to analyze the products of each separate process. The constancy of the tonnage and the uniformity of the quality of the feed render this practicable. No. 1.—550 tons of feed, all having passed 30 mm., is washed into two 15-mm. trommels, 4 ft, in diameter, 60 in. long, 17 rev. per min., 1 in. slope, 3/8-in. gauge steel.

Jan 1, 1913

By Roshan B. Bhappu

This is the Centennial year of AIME and many of us reading this issue of ' will be getting ready to attend the Centennial Celebration in New York from February 26 through March 4. The officers of the Division sincerely hope that a large number of our members will attend the fine technical sessions and social functions arranged for this really big meeting. The year 1971 will be a crucial one for MBD. This SME Division is a working group organized "to furnish a medium of cooperation among those interested in the basic unit processes and unit operations of minerals beneficiation; and to promote the advancement of this branch of mineral technology through meetings for professional intercourse, and to stimulate the preparation, reading discussion and circulation of papers connected therewith." No one can deny the worthiness of these objectives or minimize the efforts that Division officers and members have made to attain them. Much has been done over the past several years to achieve a smooth-running and effective MBD organization. However, there is still room for improvement and much more needs to be done in order to provide the best possible services for the membership and the profession.

Jan 1, 1971

By M. R. Tek, K. H. Coats, D. L. Katz

The performance of a gas reservoir su,bject to water drive is often affected by interference due to gas procluction or injection in neighboring reservoirs adjacent to a common aquifer. Field data available on production-pressure behavior of several reservoirs indicate that prediction of reservoir performence must include the effects due to mutual interference. A method developed to predict the performance of two or more interfering gas reservoirs, subject to specified production-iniection .rchedule.s, is presented. The method involves the comhinatiorz of the theory of unsteady-state water movernent with appropriate meterial balance consideration.s. The procedure which extends M. Mortada's treatment for interfering oil reservoirs makes use of his dimen-.sionless pressure drop quantities. prevented graphically in the literature. In order to evaluale the predictive accuracy and practical field applicability of the theory, the method has been applied to analyze the performance of two actual gas reservoirs in mutual interference. The calculations were performed on an IBA4 704 computer. The predicted performances were alro calcltlated with the interference effects ignored. The results show that considerably better agreement between calculated and observed behavior ic. obtained when the interference effects are included. INTRODUCTION Fluid communication between any number of oil or gas reservoirs adjacent to a common aquifer results in mutual interference effects on their production-pressure behavior. The theory, application and interpretation of pressure build-up behavior of oil wells, drawdown tests on oil or gas-producing formations and behavior of several storage reservoirs indicate ample experimental evidence of mutual interference. A method developed to compute the behavior of interfering oil reservoirs was published several years ago by Mortada.4 Studies conducted during the recent years on underground storage of natural gas clearly indicated the need for extending Mortada's work to the case of interfering gas reservoirs. The adoption of appropriate material balance equations in conjunction with the unsteady-state pressure interference theory yields pressure-explicit equations. Their solution, their application to a specific case history and an over-all evaluation of the developed method through the comparison of predicted and observed field performances were the main objectives of this study. DEVELOPMENT OF MATHEMATICAL RELATIONS The diffusivity Eq. 1 governs planar, radial, unsteady-state compressible liquid flow through a porous medium. ?p/?r2+1/r ?p/?r=µFc/k ?p/?t (1) The 1iterature1,2,3 contains derivations and solutions of

By Donald A. Dahlstrom

In 1961 it became increasingly more evident that significant technological changes must be made in minerals beneficiation. The status quo in technology in today's competitive markets will not be tolerated. Higher productivity, greater recoveries and newer and better products must be sought and incorporated with lower operating costs. In other words, "when you build a new mill, don't build an old mill." Recommended reading for proof of the vital necessity of new methods and techniques is in the September 1961 issue of MINING ENGINEERING. The article by one of MBD's cherished and true veterans, E. H. Rose, is entitled "Iron Ore: The BIG Picture". Because of new beneficiation methods for iron ores, nearly 47 million tons of plus 60% iron concentrates will be produced and another 40.1 million tons of capacity will be under construction or committed. Thus in a relatively short period, 87 million tons of this high-grade iron concentrate with record low silica will be available. As Mr. Rose also points out, "in gross tons, without allowance for better grade, this is the equivalent of almost exactly two-thirds of all iron ore used for all purposes in the U.S. and Canada in the peak years of 1953 or 1957." Needless to say, improved mineral beneficiation methods have had far more reaching effects than just the production of higher grade iron concentrate.

Jan 2, 1962

By LESTER W. STRAUSS

OUR early knowledge of history and geography attracted most of us to the mineral resources of South America. The romantic tales of the Spanish activities, which were curiously alluring, and Prescott's exceptional bi-Conquest histories-Mexico and Peru-no doubt fired our minds with the .then metallic wealth of the Spanish colonies. Later developments, intensified within the past eighty years, have, however, changed its fame which now rests on such metallics as copper and tin, and among the non-metallics on nitrate of soda and petroleum. South America proper, excluding Panama, is made up of thirteen countries, a coincident parity with our original thirteen States. Its area is given as 7,231,300 square miles, or slightly less than North America (8,037,000 square miles), is made up as follows:

Jan 1, 1930

By Marcus Grossmann

THIS paper offers for consideration certain somewhat radical modifications in the iron-carbon diagram, these modifications being the result of the presence of notable amounts of alloying elements. When only small amounts of alloys are present, 'the standard iron-carbon diagram (Fig. 1) can be used with but insignificant changes; when larger amounts of Chromium, Per Cent FIG. 1.-IRON-CARBON DIAGRAM. FIG. 2.-IRON-CHROMIUM DIAGRAM. alloys are present, however, it assumes a distinctly altered appearance. No comment is offered for the present except to call attention to the delta area, A4BM, which represents a region of mixtures of austenite and delta iron, just as area A3SP represents mixtures of austenite and alpha iron.

Jan 12, 1926

By E. T. Turkdogan, P. Grieveson

STAFF: Editor, Gerhard Derge Acting Editor, Paul G. Shewmon Carnegie lnstitute of Technology Sc hen ley Park Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: Karl L. Fetters, President; J.S. Smart, Jr., Past-President; R. C. Cole, Vice President; R. L. Hennebach, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: W. 0. Phil-brook, Chairman; H. L. Bishop, R. C. Cole, J. N. Hobstetter, W. A. Krivsky, E. R. Morgan, F. C. Langenberg, R. E. Lund, Paul Queneau, L. L. Seigle, R. L. Smith, and T. '4. Wainwright. Review and selection of manuscripts is under the supervision of the following Publications Committes: Extractive Metallurgy Division: R. E. Lund, Chatrmon; M. E. Wodsworth, Vice Chairman; D. H. Baker, Jr., G. M. Bell, R. E. Groce, W. A. Krivsky, R. A. Lewls, Charles O'Neill, A. W. Schlechten, R. E. Shinkoskey, and W. W. Stephens. Iron and Steel Division: T. V. Wainright, Choirman; H. L. Bishop, R. E. Boni, T. E. Dancy, C. W. Murphy, Johonnes M. Uys, J. B. Wagstaff, and R. G. Ward. lnstitute of Metols Division: J. N. Hobstetter, Chairman; P. A. Beck, J. J. Becker, G. F. Bolling, J. O. Brittain, J. 8. Clark, R. S. Davis, A. E. Dwight, R. W. Fountain, L. R. Girifalco, J. C. Gurland, H. S. Kclish, E. L. Harmon, J. J. Heger, A. A. Hendrickson, L. Himmel, J. P. Hirth, H. H. Johnson, Jr., R. R. Nosh, T. N. Rhodin, R. H. Richman, H. C. Rogers, W. Rostoker, C. Sherby, C. W. Spencer, L. Slifkin, J. K. Stanley, R. Steinitz, H. C. Stumpf, and R. Swolin. Published bimonthly by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc., 345 East 47th Street, New York 17. N. Y. Telephone PLaza 2-6800. Subscription $30 per year for non-AIME members in United States and North, South, and Central America; $32, foreign; $7.50 for AlME members. Single copies, $6.00, single copies foreign, $6.50. The AlME is not responsible for any statement made or opinion expressed in its publications ... Copyright 1962 by the American lnstitute of Mining, Metollurgical. and Petroleum Engineers. Inc. . . . Registered cable address, AlME New York . . . Indexed in Engineering Index, lndustriol Arts Index, and Chemical Abstracts . . . Second class postage paid at New York, N. Y., and Ann Arbor, Mich. Volume 224, Number 6.

Jan 1, 1962

By Joseph T. Singwald

INTRODUCTION THE purpose of this chapter is to present the diagnostic features (geologic, mineralogic, chemical, and physical) of the principal types of hypogene ore deposits recognized in current genetic classifications, and to classify the ore deposits of the western United States into those types. The genetic divisions used and the criteria determining them are essentially those followed by Lindgren in his Mineral Deposits. Deviations from Lindgren represent either changed conceptions since 1928 (the date of the third edition of Mineral Deposits) due to advance in knowledge or the inevitable differences of opinion between experts in active fields of investigation. Though nineteen economic geologists have been given free hand in presenting their particular topics, there are no fundamental departures in the chapter from the principles set forth by Lindgren. It would be entirely beyond the capacity of a single chapter to give a comprehensive geologic description of all the ore deposits of the western United States. Descriptions of individual deposits have been restricted to those features that are of most diagnostic genetic value. All of the more important deposits receive that much attention. Deposits of lesser economic importance and those inadequately known geologically are treated more briefly or merely cited under what seems to be their proper genetic assignment. The geographic limits of the descriptive matter are the Black Hills and the United States between the Rocky Mountains and the pacific Coast. Capacity of the chapter has made it necessary to impose these geographic limits.

Jan 1, 1933

By executive order of the President, dated June 25, 1918, the investigation of matters relating to gas warfare, which had been initiated by the Director of the U. S. Bureau of Mines early in 1917, and had been continuously maintained and improved since, that time, was transferred to the recently created Division of Gas Warfare of the War Department. On the occasion of this transfer, both the President and the Secretary of War took occasion to speak most highly of the efficient service that had been rendered by the Bureau of Mines. It gives us great pleasure to reproduce here a letter from the President and from the Secretary of War, bearing on this subject and also to append a brief review of the work of the Bureau of Mines, prepared by its Director, Mr. Van H. Manning. The White House, Washington. June 26, 1918. MY DEAR MR. MANNING: I have had before me for some days the-question presented by the Secretary of War involving the transfer of the chemical section established by you at the American University from the Bureau of Mines to the newly organized Division-of Gas Warfare in which the War Department is now concentrating all the various facilities for offensive and defensive gas operations. I am satisfied that a more efficient organization can he effected by having these various activities under one direction and control, and my hesitation about acting in the matter has grown only out of a reluctance to take away from the Bureau of Mines a piece of work which thus far it has so effectively performed. The Secretary of War has assured me of his own recognition of the splendid work you have been able to do, and I am taking the liberty of enclosing a letter which I have received from him, in order that you may-see how fully the War Department recognizes the value of the services. I am to-day signing the order directing the transfer. I want, however, to express to you my own-appreciation of the fine and helpful piece of work which you-have-done, and to. say that this sort of team work by the bureaus outside of the direct war-making agency is one of the cheering and gratifying evidences of the way our official forces are inspired by the presence of a great national task. Cordially yours, Dr. Van. H. Manning, WOODROW WILSON. Chief, Bureau of Mines, Department of the Interior. War Department, Washington, June 25, 1918. MY DEAR MR. PRESIDENT: In connection with the proposed transfer of the chemical section at. American University from the Bureau of Mines to the newly constituted and consolidated Gas Service of the War Department, which you are considering, I am specially concerned to have you know how much the War Department appreciates the splendid services which have been rendered to the country and to the Army by the Department of the Interior, and especially by the Bureau of Mines under the direction of Dr. Manning. In the early days of preparation and organization, Dr. Manning's contact with scientific men throughout the country was indispensably valuable. He was able to summon from the universities and the technical laboratories of the country men of the highest quality and to inspire them with enthusiastic zeal in attacking new and difficult problems which had to be solved with the utmost speed. I do not see how the work could have been better done than he did it, and the present suggestion that the section now pass under the direction and control of the War Department grows out of the fact that the whole subject of gas warfare has assumed a fresh pressure and intensity, and the director of it must have the widest control so as to be able to use the resources at his command in the most effective way possible. The proposal does not involve the disruption of the fine group of scientific men Dr. Manning has brought together, but merely their transfer to General Sibert's direction. Respectfully yours, NEWTON D. BAKER.

Jan 9, 1918

By G. H. LeFevre

THE Metal Sales Department, with offices in New York, is responsible for the sale of the Company's products, with the exception of gold and coal. At present the department handles the sales of lead, zinc, silver, antimonial lead, , cadmium, bismuth, arsenic trioxide, and tellurium; gold is shipped direct to the United States Mint and coal is marketed by United States Fuel Company's own sales organization. The department keeps in close touch with the metal markets and collects information on marketing conditions, which it makes available to other departments of the Company. The electrolytic lead produced at the U. S. S. Lead Refinery, Inc., is a high-uality product marketed as corroding grade under the "U. S. S.-ELECTRO" brand. It is largely sold to manufacturers of paints, pigments, lead oxides, and storage batteries.

Jan 1, 1948

By C. K. Gupta, P. K. Jena

Niobium (columbium) metal in the form of a button has been produced by calciothermic reduction of niobium pentoxide using sulfur as the heat booster. In these experiments with 50 g of niobium pentoxide per batch, the influence of percentage of calcium in excess of the stoichiometric, the percentage of sulfur by weight of the niobium oxide, and the outer-wall temperature of the bomb on the quality and yield of the metal has been studied. The maximum yield on this scale was 78 pct using 50 pct excess Ca and 20 pct of S and at a bomb-wall temperature of 600°C. In experiments conducted on 500 g of niobium pentoxide, reduction with 40 pct excess Ca and 20 pct of S, and at a bomb-wall temperature of 500°C, the.yield of the metal improved to 82 to 84 pct. Some of the reduced-metal samples have been electron-beam melted and the button melts thus obtained have been observed to be extremely ductile and capable of cold reduction to 98 pct without intermediate annealing. NIOBIUM, because of its high melting point (2468oC), its ductility, its resistance to corrosion especially in liquid metals, its high-temperature mechanical properties, and its relatively low capture cross section (1.1 barns) for thermal neutrons, has potentialities as a structural material in the field of nuclear engineering. Niobium and its alloys are also gaining importance in high-temperature technology as components in aircrafts, jet engines, and missiles, electronics, chemical engineering, and surgery. In 1904 Weiss and Aichel 1 produced niobium by reduction of its pentoxide by misch-metal. Since then a large number of investigations have been carried out for the extraction of niobium from its compounds. The various routes through which the metal niobium has been extracted from its compounds can broadely be classified into the following groups: a) reduction of its halides, oxides, and fluo-salts with metals like calcium, magnesium, sodium, and aluminum;2-10 b) reduction of its halides with hydrogen and oxides with carbon or carbides;11-18 c) electrolytic winning from its halides and fluo salts;19-25 and d) thermal decomposition and disproportion ion of its halides26-30 Among the processes in commercial use at present are sodium reduction or fused-salt electrolysis of potassium niobium fluoride, carbide or carbon reduction of the oxide, and hydrogen or metallothermic reduction of the chlorides. In 1907 Von Bolton2 prepared niobium by reducing niobium pentoxide with aluminum. Dennis and Adam-sona attempted reducing the oxide with magnesium powder in argon atmosphere and the resulting metal contained as much as 5 pct O. Mondolfo8 claimed a method for the reduction of the oxides with aluminum. In the case of both magnesium and aluminum reduction, it has been stated31 that by-product oxides such as MgO or A12O3 would involve a major separation problem. Further, in the case of alumino-thermic reduction, the solubility of aluminum in niobium and intermetallic formation have to be reckoned with. In 1922 Bridge3 produced niobium by calcium reduction of niobium pentoxide. Dennis and pdamson' obtained the metal by a similar method with an oxygen content of 0.2 pct. In most of the cases of metallothermic reduction of niobium oxides mentioned above, the metal niobium is obtained in the form of powder. In an attempt to produce massive niobium metal, lock' used iodine as the thermal booster in the bomb reduction of niobium pentoxide by calcium. Massive niobium metal was obtained with a maximum yield of 75 pct containing 0.1 pct 0. Joly32 carried out experiments on calcium reduction of niobium pentoxide on a 2-kg scale using sulfur as the heat booster in a sealed bomb filled with argon. In his experiments, the reaction was initiated by passing a current through niobium spiral wire embedded in the charge. In a typical run consisting of 2000 g of niobium pentoxide, 3100 g of calcium, and 800 g of sulfur (S/Nb2O5 = 3.3), he obtained massive metal in the form of a very uneven mass with a yield of -57 pct. With lower amounts of sulfur and calcium, powder niobium mixed with small metal globules was obtained and the yield was also poor. From these experiments he concluded that this method is not a suitable one for industrial development considering the quality and yield of metal obtainable and the possible hazards with higher ratios of sulfur to niobium pentoxide in the -~charere. In the present work, a detailed investigation on the calciothermic reduction of niobium pentoxide in a stainless-steel bomb in presence of sulfur as the heat booster was undertaken on a laboratory scale.

Jan 1, 1964

CONTENTS DAVIS, CARL R., WILLEY, J. L., and EWING, S. E. T.-Recent Developments in the Fine Grinding and Treatment of Witwatersrand Ores. Discussed by Charles E. Locke, H. W. Hardinge, H. N. Spicer, G. M. Brown, Justice F. Grugan, R. C. Canby 1 WEINIG, A. J., and BOWEN, MAX W.-Determination of Dissolved Oxygen in Cyanide Solutions. Discussed by A. L. Blomfield, M. F. Dycus, A. W. Bull.... 4 LEPSOE, ROBERT.-Precipitation Efficiency of Zinc Dust in Cyanide Process. Discussed by G. M. Brown, Charles E. Locke 5 Recent Developments in the Fine Grinding and Treatment of Witwatersrand Ores Discussion of the paper of CARL R. DAVIS, J. L. WILLEY, S. E. T. EWING, presented at the New York Meeting, February, 1925, and issued as Paper No. 1386-B, with MINING AND METALLURGY, December, 1924. CHARLES E. LOCKE, Cambridge, Mass.-In this country, we have come to think that we should use smaller size of feed in our ball-mills. I will admit that a ball-mill is not comparable to a tube-mill, as conditions may not be the same, but there we have an unusual demonstration of the advantage of a coarser feed. Further investigation along this line is going to lead to some valuable results. The authors have overcome the difficulty of this coarse feed by taking out what I would call the difficult lumps, It is not clear from the paper whether many of these difficult lumps' may not be 'reduced portions of their grinding media. H. W. HARDINGE, New York, N. Y.-The idea is not exactly new because in 1911 they used the miner to reduce the finer material. We proceeded three or four years using many tons, about 15 tons. or nearly the same proportion of ore to grinding medium. Another thing to be taken into account is the hardness of the ore being ground. In South Africa, the transportation costs must be, taken into account. They are also making progress in the method of using tube-mills and ball-mills instead of stamps. Experiments are to be conducted with 10-ft. diameter mills there, with the object of increasing the mass action and agitation which, as has been demonstrated under different circumstances, increases the overall efficiency.

Jan 6, 1925

By Alan Morris

Brass rod for use in automatic screw machines is one of the major products of the brass mills. A large tonnage is consumed each year in the manufacture of an endless variety of finished articles and parts for assembly into other products. The machines that do this work have been developed to a high degree of efficiency, and their manufacturers are still striving for higher production speeds. This development has brought with it a demand for brass rod to meet the increasingly difficult machining conditions. This paper is a report of the results of tests undertaken in an effort to obtain a measure of the effects of such variables as lead content, microstructure and cold work on the machinability of brass rod. It is realized that the term "machinability" has never been well defined. Power, finish and tool life all should have a place in such a definition. In practice it is sometimes found necessary to sacrifice some of these in order to obtain a rod that will not tend to throw up a burr, or will give a burr which is easily tumbled off. Again a specially stiff rod may be necessary because of long overhang from the chuck or a rod of special characteristics is needed to take a given broaching operation without chattering. It is only through an understanding of the effect of basic mill operations on the machinability of the rod that such problems as these may be solved most economically. It is hoped that this paper, together with the discussion it may evoke, will prove to be a basis for such an understanding. Testing Apparatus The testing apparatus used was of the single-tooth milling cutter type, in all respects sirnilar to that first used and described by Airey and Oxford1 and again by Boston. The machine used in the present test is shown in Fig. 1. It is an ordinary milling machine in which a heavy pendulum has been substituted for the pulley on the arbor. If the pendulum is raised

Jan 1, 1932

R. W. Raymond, New York City: In connection with the subject of multiple tuyeres, my attention has been drawn to the practicability of gaining, without the multiplication of tuyeres, the advantages which that measure is intended to secure ; and learning that this had been attempted in the invention of the Gaines radial-discharge or fan-shaped tuyere, I wrote to Messrs. Gustafson Brothers, of Sequachee, Tenn., who manufacture that tugere, for information concerning the invention itself and its performance in practice. To their courtesy I am indebted for most of the facts given below. I present these statements without expressing any personal opinion on the subject (having no personal knowledge of it), for the purpose of bringing this device to the notice of members, and calling forth both criticism and testimony concerning it. Admitting that definite advantages are to be secured by the multiplication of tuyeres, we must still confess that this change involves considerable expense in the increased number of blastpipes, tuyeres, coolers, connections, and pipes for water-circulation. There is, moreover, a serious question involved in the weakening of the furnace-wall by extra perforations. This consideration applies with special force to furnaces already built without reference to such an increase of tuyere-openings. Ledebur, in his Handbuch der Eisenhüttenkunde, says on this point (I translate from the edition of 1893, page 365): "A limit to increase in the number of tuyeres is given, in any case, by the circumstance that the perforation of the wall weakens it; in other words, that there must be left between the tuyeres a mass of masonry sufficient to carry the parts above. In most cases an appropriate number may be secured by giving to the furnace as many openings as there are meters in its circumference at the tuyerelevel. For instance, for a hearth-diameter of 2.5 meters, i.e., a circumference of 7.7 meters, seven or eight openings might be made, of which, however, one would

Jan 1, 1899

By T. E. Evans, C. T. Baroch

ZrB2 was produced in batches of 4 to 6 Ib by interaction of ZrO2, B4C, B203, and carbon at around 2000°C in a simple graphite resistance furnace. Techniques of production are discussed and the final design of a suitable furnace is described in detail. Several other borides were made by the same technique and the process appears to have possibilities for commercial production. N seeking out new hard and refractory com- pounds, many researchers have turned to the investigation of the borides and excellent papers have been published on the properties of these compounds. Few papers, however, have appeared on the techniques and problems concerned with the production of these high temperature substances. This report describes progress made in developing a method for preparing zirconium diboride, ZrB2, on a pilot plant scale. The literature of the borides and other refractory hard metals recently has been reviewed, annotated, and classified so completely' that it is needless to attempt such an outline here. It is enough to say that three borides of zirconium have been reported: ZrB, ZrB2, and ZrB12.2 ZrB2 is the most stable of these and is especially stable in the presence of carbon up to and including its melting point of around 3000°C. Like most borides, it can be prepared in several ways. It can be prepared by synthesis of the elements, but these are expensive and difficult to produce in a high state of purity. Obviously, production directly from the oxides would have decided economic advantages. In electrolytic production such as that of calcium boride,:' the product is recovered as a sludge mixed with electrolyte; and separation of product from adhering electrolyte and regeneration of the electrolyte is an involved and difficult process. The work on borides was started on a small scale in 1948. Late in 1949, Naval Ordnance expressed a specific interest in ZrB2 and the project then centered on this compound. After the usual experimental work necessary in a new field, ZrB2 of good quality was produced by heating mixtures of B4C, ZrO2, B2O3, and carbon to a temperature of about 2000 °C in a resistance-type electric furnace. Over 100 lb was made for experimental use tests, and the method of production probably could be expanded into a commercial operation. A similar process has been described by Kieffer and coworkers.' The main chemical problems were the development of proper charges to insure complete reduction of the elements, determination of the proper temperature range at which these reductions took place, and adoption of techniques necessary to pre- vent inclusion of such impurities as carbon and nitrides. The mechanical problems consisted of developing a simple practical furnace that would attain the high temperatures required and permit use of a controlled atmosphere when necessary and determining of suitable refractories. Both problems were solved by designing a crucible resistance furnace. Crucible Resistance Electric Furnace Attempts were first made to produce ZrB2 in an electric arc furnace, but such a furnace would not provide the degree of carbon control required for producing clean graphite-free borides, so it was decided to try working in a crucible. Obviously, the furnace would have to be constructed of graphite, as the temperatures required are too high for other refractories or heating elements. Crucibles were made by hollowing out segments of graphite electrodes, which were fitted with a cover and clamped between two electrodes so that the current passing through the thin wall of the crucible would generate heat, using the principle of the Helberger crucible furnace."? Preliminary tests with this type of furnace were encouraging and led to the furnace design shown in Fig. 1. The essential components were a thin-walled graphite crucible resting on a graphite block, which formed the lower electrode assembly, and a top electrode assembly swung from a pipe column making contact with the top of the crucible. The space around the crucible was filled with graphite prepared from waste electrodes crushed to about ¼ in. This packing had excellent insulating properties, both electrically and thermally, and could be removed easily and quickly from around the crucible by means of an industrial vacuum cleaner. The largest resistor crucibles were machined from 8 in. electrode stock and were 26 in. long, with a side wall Yi in. thick and a 1 in. bottom. Temperatures were determined optically by sighting down a 1 in. hole drilled longitudinally through the top electrode and the crucible cover. Sealing this hole at the top was a water-cooled brass sight-glass assembly, shown in Fig. 2. An opening was provided for a light flow of helium to keep the sight opening clear of smoke, and a glass prism above the sight glass changed the line of sight to the horizontal for easier reading. More recently, the prism and optical pyrometer were replaced by a photoelectric recording pyrometer. At first the charges were placed directly in the resistor crucible but this meant that everything had to be withdrawn from the furnace every time the charge was emptied. Later, smaller crucibles were made up that could be placed inside the resistor

Jan 1, 1956

By William C. Aitkenhead, John A. Jaekel

Uranium deposits in the Spokane Indian Reservation, as well as those around Mt. Spokane, are essentially low grade, much of the ore containing less than 0.2 pct U808. The Mining Experiment Station of the Division of Industrial Research, State College of Washington, has been engaged in intensive research on the amenability of these low grade ores to froth flotation. The results: successful flotation of autinite, chief mineral constituent. At the outset of this work the goal was a concentrate of 1 pct U308 with a 90 pct recovery from ores containing less than 0.2 pct U3O8. Most of the work has been done on argillite ore from the Midnight mine on the Spokane Indian Reservation. The goal has not been attained using this ore, but samples of the granite ore from Mt. Spokane yielded successful results. For example, a concentrate containing 11.2 pct U308 was produced from a Mt. Spokane high grade ore containing 1.27 pct U3O8 with a recovery of 97.8 pct. Another Mt. Spokane ore yielded a concentrate of 5.0 pct U3O8 from an ore containing 0.13 pct U3O8, with a recovery of 85 pct. This same ore gave a recovery of 93.5 pct when the grade of concentrate was reduced to 2.0 pct.

Jan 1, 1959

By F.B. Foley, S.P. Howell

Not infrequently, in the case of the failure of a metal structure, such as a bridge, tank, airplane, gun carriage, etc., a doubt arises whether the failure was due, among other causes, to the effect of an overburden or of an explosive maliciously or accidentally exploded in contact with it. As few means of discriminating between the effects of these causes have been known and these means were of a rough qualitative character, it was surprising to find in the record of an inquiry into the failure of a structure, the statement that, by observations on the Neumann bands in the structure, it was possible to determine the speed of breakage in the metal and to distinguish between a fracture caused by an explosion and one caused by an ordinary mechanical strain. Such a criterion, if well proved, was of value to the explosives experts of the Bureau of Minea, the Ordnance Department of the United States Army and the Bureau of Ordnance of the United States Navy, but search showed no record of it in the literature nor did any of the metallurgists and metallographers consulted know of any data on which such a criterion could be based having been assembled and critically studied. However, it was universally held that there was promise in the idea and that there exkted unique facilities at the Bureau of Mines Experiment Station at Pittsburgh for the preparation, under definitely known conditions, of material for study by metallographers, and that material of value might also be obtained from the proving grounds of the Army and Navy. Therefore, with the approval of the Director of the Bureau of Minea and the Chiefs of Ordnance of the War and Navy Departments, the Chairman of the Division of Engineering of the National Research Council, on April 12, 1919, appointed a Committee on the Investigation of Neumann Bands, which has since been engaged in this study and which, after some slight change in its personnel, consists now of the following: Dr. William Campbell, Advisory Metallurgist, Bureau of Ordnance, Navy Department. P. B. Foley, Metallurgist, Bureau of Mines. S. P. Howell, Explosives Engineer, Bureau of Mines. Comdr. 0. M. Hustvedt, U. S. N., Bureau of Ordnance, Navy Department. Dr. Charles E. Munroe, Chief Explosives Chemist, Bureau of Mines.

Jan 1, 1923

By S. P. Howell, F. B. Foley

Not infrequently, in the case of the failure of a metal structure, such as a bridge, tank, airplane, gun carriage, etc., a doubt arises whether the failure was due, among other causes, to the effect of an overburden or of an explosive maliciously or accidentally exploded in contact with it. As few means of discriminating between the effects of these causes have been known and these means were of a rough qualitative character, it was surprising to find in the record of an inquiry into the failure of a structure, the statement that, by observations on the Neumann bands in the structure, it was possible to determine the speed of breakage in the metal and to distinguish between a fracture caused by an explosion and one caused by an ordinary mechanical strain. Such a criterion, if well proved, was of value to the explosives experts of the Bureau of Minea, the Ordnance Department of the United States Army and the Bureau of Ordnance of the United States Navy, but search showed no record of it in the literature nor did any of the metallurgists and metallographers consulted know of any data on which such a criterion could be based having been assembled and critically studied. However, it was universally held that there was promise in the idea and that there exkted unique facilities at the Bureau of Mines Experiment Station at Pittsburgh for the preparation, under definitely known conditions, of material for study by metallographers, and that material of value might also be obtained from the proving grounds of the Army and Navy. Therefore, with the approval of the Director of the Bureau of Minea and the Chiefs of Ordnance of the War and Navy Departments, the Chairman of the Division of Engineering of the National Research Council, on April 12, 1919, appointed a Committee on the Investigation of Neumann Bands, which has since been engaged in this study and which, after some slight change in its personnel, consists now of the following: Dr. William Campbell, Advisory Metallurgist, Bureau of Ordnance, Navy Department. P. B. Foley, Metallurgist, Bureau of Mines. S. P. Howell, Explosives Engineer, Bureau of Mines. Comdr. 0. M. Hustvedt, U. S. N., Bureau of Ordnance, Navy Department. Dr. Charles E. Munroe, Chief Explosives Chemist, Bureau of Mines.

Jan 1, 1923

By Richard W. Bayley

The Atlantic City district encompasses several districts and has been previously called by different names, e.g., Atlantic gold district, Atlantic City-South Pass mining district, and Sweetwater mining district. The district is located in a terrane of folded and faulted early Precambrian metamorphic rocks which lies near the south end of the Wind River Range in Fremont County, Wyoming, Historically it is a gold district of little production, but today is an iron district of considerable importance. Gold was discovered in placer deposits about 1842 and in quartz-arsenopyrite veins about 1867, after which there occurred a mining boom lasting a few years. Minor, intermittent gold production from placers and lodes has continued to date, but the total production has probably not exceeded a few millions of dollars. Past lode mining was generally shallow ( in the oxidized zone), the deepest about 3 60 feet. The deeper, less oxidized and sulfide ores on the same lodes have not been explored. They appear to hold the only hope for future gold mining. Sedimentary iron-formation, similar to the Lake Superior taconite, occurs in the northern part of the district. Locally, where the ironformation is thickened by folds and faults, sufficient tonnages are present to be minable, as at Iron Mountain, where the U.S. Steel Corporation produces about 1.3 million tons of iron-ore pellets annually. Exploration of the iron deposits began in 1954, and the first ironore pellets were shipped to Provo, Utah in August 1962. Indicated reserves of iron-formation (about 30 per cent Fe) are reported to be about 300 million tons.

Jan 1, 1968