Search Documents

By W. Jolley

Decarburized iron and Fe-3.28 pct Ni alloys were impact and tension tested in the temperature range of ambient to 4°K. It was found that alloying with nickel improves the fracture properties of the ferrite matrix. The improvement in toughness of iron alloyed with nickel is attributed to the effect of the nickel addition on the temperature and strain rate dependence of the yield stress as well as on slip behavior. The Fe-Ni alloy exhibits wavy slip when strained at temperatures down to at least 50°K. This behavior contrasts with that of the unalloyed iron where a change It is a generally accepted fact that of the common alloying elements of steel only nickel and manganese improve both the room-temperature yield strength and the notch impact properties. It has been argued for a number of years that manganese refines the ferrite grain size, the pearlite spacing, and the grain boundary carbides in medium- and low-carbon steels and thereby increases resistance to brittle fracture.''' This hypothesis recently was confirmed for a 0.04 pct C iron containing manganese, but at the same time from wavy to planar slip occurs at about 120°K. The observed lower temperature and strain rate dependence of the lower yield stress in the Fe-Ni alloy as compared to the unalloyed iron may be attributed to this difference in slip behavior. In contrast to suggestions published previously, transmission electron microscopy showed that the uniform dislocation distributions and the lack of dislocation tangles which are produced by low-temperature straining of bcc materials cannot be attributed to the absence of cross slip at these temperatures. no increase in notch toughness was observed in a decarburized Fe-Mn alloy.3 It thus appears that manganese only increases the toughness of Fe-Mn-C alloys by refining grain boundary carbides and has no toughening effect in carbon-free iron. On the other hand, the mechanism whereby nickel improves toughness has not been established. Hodge et a1.4 have clearly shown that a 3.28 pct Ni addition lowers the impact transition temperature of 0.02 pct C steel approximately 35°C when the grain size is maintained constant. Recently, Wullaert and Tetelman6 stated that nickel refined the grain boundary carbides of an Fe-C alloy and consequently increased the toughness. They also observed the previously reporteda-'

Jan 1, 1969

By Lewis A. Smith

Chromium is one of the new metals, but considerable research has been required to determine an approximate record of its production from 1827 until the present. Its use in the form of pure metal is not extensive; of the chromite mined, about one-half is required for making ferrochro-mium, about two-fifths goes directly into refractories and the remainder is absorbed chiefly by the chemical trades. The industries that demand chromite for such uses are mainly in countries that produce little chromite, while the important chromite-producing countries are not generally consumers. The international flow of chromite is therefore of interest, as well as the political and commercial control of resources of the metal. World Production The first mining of chromite is said to have occurred as early as 1820, at the Roros deposit in Norway, but the first well-established output came from the Reed mine, in Maryland, about 1827. Thereafter the United States led the world in chromite production until 1860, when Turkey took the lead. Russia in turn became the chief producer from 1897 to 1902, inclusive. From 1903 to 1909, New Caledonia held first place, but alternated with Southern Rhodesia from 1910 to 1917, inclusive. In 1918, 1919 and 1920-1921, the United States, India and New Caledonia led, respectively. In 1922 Southern Rhodesia assumed first place and has since continued to be the world's foremost producer by a large margin. Fig. 1 illustrates the production of the leading countries from 1890 to 1929, inclusive. Fig. 2 shows the world production of chromite from 1890 to 1929, inclusive, in long tons and Table 2 gives the production by countries for the same period. The total world production for the 103 years, 1827 to 1929, ipclusive, is estimated at about 7,100,000 long tons, distributed as shown in Table 1. World Trade in 1928 In reviewing the figures for the flow of chromite in 1928, it is evident that the six countries that produce most consume little chromite and

Jan 1, 1931

By Samuel Wyer

1. THE following is an abridgment of a recent report made by the author, covering an investigation of (A) The necessary use of natural-gas compressors; (B) The effect of gas compressors on natural-gas field operating conditions in Ohio, with special reference to the working pressure relations of gas wells of one company discharging by natural rock pressure flow without compressors, and adjacent wells of other companies, discharging into intake lines to gas-compressing stations. Tests were made at 107 different places in the counties of Fairfield, Licking and Knox, Ohio, which required 7,000 miles of automobile driving, and consumed 6 months' time. 2. A proper conception of. the necessary use and effect of natural-gas compressors in natural-gas production necessitates a clear understanding of certain fundamental definitions and judicial doctrines, which are given herein. 3. Gas is a fluid composed of a large number of molecules which are vehicles of energy continually in motion, and having an inherent. tendency to get farther and farther apart. The range of motion of the molecules is limited only by the volume of the closed containing vessel in which they constantly move to and fro. The most distinguishing characteristic of gas is its universal property of completely filling an inclosed space.

Jan 2, 1916

By Wilbur I. Duvall, James F. Devine

7.4-1. Introduction. Ever since explosives were discovered and developed for mining purposes, there has existed the problem of determining what effect the air and ground vibrations resulting from blasting have on structures of various types. This problem is especially acute for surface operations such as open pit mines, quarries, and construction projects that are in the proximity of residential districts, scientific laboratories, or other vibration-sensitive structures. Because the general public is directly involved in the blasting vibration problem, it has been of major concern to local, state, and federal governments, as well as to mining and construction companies, explosive manufacturers, insurance companies, and scientific investigators. Consequently, many investigations have been conducted, both in this country and abroad, on the effects of air and ground vibration on residential and other structures. E. H. Rockwell made some of the first studies in this country on the vibrations produced by blasting and the effect that these vibrations have on structures (18). In his publications, he stressed the need for measuring the vibrations from quarry blasting in order to establish the level of vibration as a function of charge size and distance. The concept of a damage criterion for structures was developed shortly thereafter, and a displacement of less than 0.03 in. was considered safe. During the period from 1939-1942, the Bureau of Mines conducted an extensive investigation on the problem of seismic effects of quarry blasting. This work, summarized in Bulletin 442 (20) was the first major effort for establishing damage criteria for residential structures based on experimental data. An acceleration of less than 0.1 g was considered safe, 0.1 to 1.0 g was caution, and greater than 1.0 g was damage. This work

Jan 1, 1968

By R. L. Frantz, R. W. Bouman

The authors investigated the comminution of quartz and limestone mixtures in a ball mill, showing that the distribution modulus of a comminuted material is the same whether it is ground separately or as part of a mixture. Analysis of the ground products indicates that quartz and limestone consume energy during ball milling in proportion to their mass fraction in the mixtures. Recently Schuhmann' made a significant contribution to comminution theory by proposing that complex comminution operations comprise the summation of many individual comminution events. By means of the single comminution event hypothesis, Schuhmann derived the Charles energy-size reduction relationship by considering that fragments of every particle crushed during a single impact have a size distribution characterized by the Schuhmann size distribution. In this paper, the size reduction of mixtures of solids in ball mills is analyzed by considering that size reduction occurs as many single comminution events. If a mixture of two materials is being ground in a ball mill, each successful impact of a ball with a particle of one material should yield an assembly of particles whose size distribution is characteristic of that material. Considering both materials to follow the Schuhmann size distribution equation, the size distribution of material 1 in the product is

Jan 1, 1962

Discussion of Papers. Meetings of the Institute offer opportunity for social acquaintance and exchange of ideas, for the presentation of papers, and for discussions thereon ; also incidentally for viewing under especially favorable conditions mining operations and industrial establishments, and for hospitals-ties which demonstrate the brotherhood due to kindred interests. Placing sociability prominent is not to be assumed as relegating other features of meetings to subordinate positions; but during about 40 years of membership in the Institute, the value of acquaintances formed (often ripening into close friendship), and the interchange of data, have frequently demonstrated that the social feature of meetings is of great and lasting value to the membership. Of' a roll embracing 4,011 members, resident in all parts of our country, and scattered in various portions of the world, only a small fraction are able to attend meetings, even if the localities selected are alternately widely separated. Hence, the return which most -members receive for their annual assessment of dues is limited to the publications issued, and the credit of being recognized as a member of a great and worthy organization. Tile greater the value of tile contents of our publication, the fuller the return which goes to members. While the Institute disavows responsibility for views or statements made in papers which appear in its Transactions, the fact that these contributions, after passing proper censorship, are accepted by the Institute and spread before the world may properly be received by the writers as endorsements of their (the writers') ability to present a specific technical or industrial proposition worthy of being carefully read. But the mere presentation and publication of contributed papers falls short of fulfilling one important feature of our meetings. If the purpose is confined to having the writers' views, discoveries, theories, or methods published, this can be obtained through the technical or trade journals and magazines.

Jan 7, 1913

By Howard I. Epstein, John R. Buzek

Thickeners are simply large tanks, usually circular in shape, which are designed to allow settling of solids and to operate with continuous overflow of clear water and underflow of thick pulp. The dimensions of the thickener are usually such that dewatering of very fine pulps may be accomplished while still overflowing clear water. Some thickeners such as the Center, Hardinge and Hydrotator types combine thickening with filtering2 while others such as the Dorr type are pure thickeners. l .2 , 3 A schematic diagram of the traction type Dorr thickener is shown in [Fig 1]. This type is appropriate for tanks over 15 m (50 ft) in diameter. This tank employs a rotating raking mechanism which moves the settled material toward the central discharge. For this and other thickeners, it is common to have a shallow conical tank bottom in order to conform to the geometry of the raking mechanism, and it is often desirable to elevate the tank for ease of access to the product. When the tank does not rest on the ground, the forces resisted by the cone are large, and thick plates must be employed. The fabrication of these tanks requires temporary supports in order to erect the cone. A flat-bottomed tank could also be used because the settled material would soon form a hardened conical surface. However, because of the presence of large bending forces, even larger plate thicknesses are required than for the conical bottom. Significant cost savings often can be realized by the use of a scalloped-bottomed tank such as the one partially shown in [Fig. 2]. The particular scalloped bottom discussed in this paper employs radial beams forming the outline of the cone-shaped bottom. These beams are supported directly by columns. Cone segments are hung between adjacent beams. The exact geometry of these segments depends upon the cone angle and radius, the number of radial beams, and their inclination. The geometry is chosen to satisfy certain clearance restraints and to utilize the material as efficiently as possible. The resulting thickness of these segments is significantly less than that of the equivalent plate for the tank with a conical bottom. This result, along with the simpler fabrication procedures required, accounts for the cost savings associated with this design. The raking mechanism employed may be the same as for the conventional conical bottom since the settled material soon forms a conical surface. Determination of the internal force mechanism for the scalloped bottom leads to designs that utilized material efficiently and thus maximize the cost savings. The complicated geometry of these bottoms along with the difficulty in analyzing the structure are factors which may have limited the use of scalloped-bottomed tanks to date. When such tanks have been built, the uncertainties associated with the internal forces have led to designs that are somewhat inefficient. In this paper, equations relating the geometric parameters are presented along with simplified closed-form solutions for the internal forces in the cone segments, from which the loads applied to the beams and the loads carried to the cylindrical tank shell can be deduced. An example is presented to show the magnitude of the savings which may be realized with this configuration.

Jan 1, 1979

By H. W. Graham

THE young metallurgist of today who thinks casually of the technical literature of the steel industry might conclude that little has been published concerning the Bessemer process. This conclusion is true as relating to the last decade or two, but there is a fairly voluminous Bessemer literature in the period of 1860 to 1910, Since that time, however, an entirely new level of metal-lurgical knowledge of steelmaking has been reached; and the present paper is simply an effort to look broadly from this new level and to bring the recorded history of the process up to date, It is an effort to appraise the acid Bessemer method of steelmaking in the light of today's technical knowledge thereof. In this paper matters of history will be dealt with only insofar as they contribute to an understanding of today's situation. Attention will be directed to the apparent causes of past developments in seeking to perceive the true direction of trends now in existence and effective as bearing upon future developments. The paper will discuss the economics of the Bessemer process, but only to the extent that will bear upon the metallurgist's understanding of his respon-sibility. The problem of the quality of Bes-semer steel will be reviewed and examples will be given of the technical data upon which the reasoning of the paper is based, Matters of engineering design, mechanical maintenance, operation and metallurgical investigation will be surveyed. Compari-sons will be made between the Bessemer and open-hearth processes for the sake of clear and ready understanding,

Jan 1, 1940

By V. F. Zackay, W. A. Goering

ALLOYS of iron and aluminum up to 35 wt pct aluminum are single-phase solid solutions, and are of potentially wide applicability.1-3 In spite of early and continued interest1-4 little progress has been made until recently in the preparation and evaluation of sound alloys containing more than 6 wt pct aluminum. Vacuum-melting techniques for the production of ductile Fe-A1 alloys have been described recently.1-7 A. procedure for air melting these alloys is presented here. Low-carbon iron is induction melted without a slag in a rammed magnesia crucible. At the beginning of melt-down, aluminum pig (99.95 pct Al), charged in a clay-graphite bottom-pouring crucible is placed in a pot furnace at 1800°F. The primary deoxidation of the molten iron after melt-down is effected by the addition of 0.1 pct aluminum and 0.5 pct manganese. (Hilty and Crafts" have reported a significant increase in the deoxidation efficiency of the aluminum and manganese combination over that of the aluminum alone.) A more drastic deoxidation designed to reduce the oxyen content to the lowest possible level is accomplished by plunging metallic calcium to the bottom of the melt. This is done by wiring small cubes of the metal to a steel rod. A circular shield larger than the diameter of the crucible opening is attached to the rod so that any spa'ttering of the molten metal will not endanger the operator. Since the temperature of the molten metal is above the boiling point of calcium, the bath is vigclrously purged by calcium vapor. It is believed that the calcium-vapor treatment permits a homogeneous distribution of calcium in the melt. Owing to the vigor of the reaction the temperature of the molten metal should be kept below 2900°F prior to the calcium addition. A total of 0.05 pct calcium is added in two stages in this manner. The second calcium deoxidation is made just before charging the molten aluminum into the iron, in order that an excess of calcium be present for the remainder of the melt. The aluminum, which has been removed from the holding furnace, is then hydrogen degassed by bubbling chlorine through a quartz tube immersed in the molten aluminum. The hydrogen-chlorine reaction is an exothermic one preventing the solidification of the aluminum during the 5-min chlorination. Approximately 0.1 pct calcium, based on the amount of aluminum, is then added to the aluminum. A further excess of calcium is introduced into the melt in this manner. The oxide dross is removed, fluorspar is added to the molten iron, and the molten aluminum is poured through the fluorspar slag. The fluorspar should be dried thoroughly prior to its use, as any water present will react with the aluminum. Aluminum oxide formed during the pouring operation reacts with the fluorspar slag to form gaseous aluminum fluoride and calcium oxide. A forced-draft ventilating system is required for this operation as aluminum fluoride is toxic. As soon as the molten aluminum has been added, vigorous manual stirring of the melt is required because the slag-aluminum oxide reaction is highly exothermic and tends to take place near the top of the melt. The combination of high temperature and the slagging action of the fluorspar quickly erodes the crucible at the slag line if the aluminum is not stirred uniformly into the melt. It has been found that at least 4 min of manual stirring combined with induction stirring are necessary to ensure homogeneity. The power is shut off 1 min prior to pouring to allow metal and slag to separate. As much slag as possible is removed from the melt, which is then poured directly into cast-iron molds. A mold wash of aluminum oxide is used to prevent ingot sticking. For slab ingots which are to be rolled into sheet, a carbon-tetrachloride vapor atmosphere or a chlorinated-pitch mold wash is desirable, as the aluminum oxide formed in the pouring operation is subsequently removed by the chlorine in the presence of carbon." As in vacuum melting, a pouring temperature of about 2900°F is recommended. Adequate hot-topping is important as iron-aluminum ingots are subject to very deep piping. Ingots are removed from the molds and buried in vermiculite, where they are allowed to cool slowly to room temperature. The ingots are radiographed,

Jan 1, 1959

By Robert F. Love

Deep under the hills of southwestern Wyoming lies a nonmetallic mineral deposit of incredible dimensions and value. This nearly pure, horizontal bed of the mineral trona, a sodium sesquicarbonate (Na2HC0,.NaHC08.H20), is found in the Green River formation some 1500 ft below surface. It is believed that evaporation of an ancient saline lake left this sodium carbonate as the evaporite and mysteriously left practically no sodium chloride, which is the common constituent of an evaporated saline lake. The trona bed averages 10 ft in thickness and extends over an area of several hundred square miles. In 1938 a geologist with the U. S. Geological Survey identified the trona in the core from a former oil exploration drillhole. By so doing, he initiated the developments of a chemical industry of impressive growth in the area, an industry on the threshold of further and much more spectacular growth. A drilling program by the Union Pacific Rd. and Intermountain Chemical Co. in the early 1940's succeeded in blocking out mineable reserves of several hundred million tons. Development of the deposit started in 1946 with the sinking of a 12-ft diam, concrete-lined shaft 1500 ft deep-followed by construction of a small pilot calcining plant. Actual mining of the trona started in 1947 and continued on a limited scale until 1953, when the $15 million surface facilities were completed, along with the second shaft and other expanded underground facilities. Since April 1953 the mine has been producing more than half a million tons per year, from which the refining plant has produced more than 300,000 tons per year of high quality soda ash.

Dec 1, 1956

By George B. Clark, John W. Brown, Hemendra N. Kalia, Ronald R. Rollins

A new theory for three dimensional collapse of conical liners shows why the two dimensional theory may offer a good approximation. Shaped charge design parameters and rock target properties were investigated to determine their effects on penetration and breakage. Penetration in dolomite is somewhat similar to that in steel, but copper does not have markedly better penetration capabilities than brass. Several metals, liner thicknesses, cone angles and standoff ranges for each were investigated. Effective standoff is greater for aluminum than more dense metals. Optimum geometry appears to approximate that for metal targets. Resistance to penetrations was greatest for a red granite and dense siliceous rocks, and least for dolomite and porous sandstone. Hardness and compressive strength appear to be two important conventional proper- ties. The first order law does not apply to the rocks tested. Dolomite may be drilled with shaped charges, the holes sprung and round blasted successfully.

Jan 1, 1971

By M. Paulus

It is known that multicomponent powders are mostly nonhomogeneous. This paper investigates the effects of nonhomogeneity of composition and grain size on the melting point and the sinterability of compact taking into account homogenization mass transport and the length of the diffusion path in solid state sintering, and the kinetics of liquid phase formation in liquid phase sintering. After a discussion on the ideal characteristics of a powder for sintering and low temperature reaction, the main conventional processes are compared. Finally we develop the freeze-drying technique and demonstrate the capabilities and the limits of the process by some examples, mainly in the ceramics field.

Jan 1, 1980

By H. Nakazawa, I. Iwasaki

Galvanic contact, occurring between electrically conducting minerals in flotation pulps, may affect the nature of mineral surfaces and influence their floatabilities. Rest potential and galvanic current measurements were made on an electrode combination of pyrite and pyrrhotite under nitrogen, air and oxygen aeration conditions. The results were correlated with their oxygen-consuming characteris- tics and flotation behaviors. The galvanic contact improved the floatability of pyrrhotite, but adversely affected that of pyrite. Auger electron spectroscopy, X-ray photoelectron spectroscopy, and scanning electron microscopy indicated that the formation of hydroxide or oxide and sulfate species of iron on pyrrhotite decreased, whereas that on pyrite increased when these minerals were held in contact. An electro- chemical mechanism was proposed for the observed behaviors.

Jan 1, 1986

By Herman Blumenthal, Ronald Silverman

lnfiltrability of a porous Tic compact, produced by powder metallurgy technique, depends on the capillarity of the compact and the surface condition and nature of the individual particles. Capillary forces raise the liquid metal infiltrant into the interconnected pores of the compact and the complete filling of these pores is a function of their geometry as well as the wettability of the Tic particles. The paper deals especially with the improvement of this wettability through surface conditioning of the Tic particles. INFILTRATION, a technique for preparing dense powder metallurgy parts by filling the void spaces of a porous body with a liquid metal, has been used for the manufacture of titanium carbide-base cermets. Although the infiltration process was

Jan 1, 1957

By Kung-Ping Wang

This is the second installment of two-part article on the Far East. The mineral situation in Hong Kong, Indo-China, Thailand, Burma, Malaya, Indonesia, the Philippines, and British Borneo is covered.

Jan 12, 1951

By James J. Scott

A four-year program of research, development, and field testing has led to the refinement of a ground support system utilizing friction rock stabilizers, or "Split Sets," as they are known by their patented trade name. These rock anchors are a distinct departure from conventional anchors or fully grouted anchor systems, and allow control of ground movement internally in a manner that permits controlled deformation during the early phase of rock "relaxation" around a mine opening, increased anchorage per unit length during the secondary creep stage, and have the ability to strengthen and stabilize mine openings for extended periods of time.

Jan 7, 1977

By W. C. Meyer, R. R. Klimpel

A physical model of flotation, derived from viewing froth as a kinetic species since it constitutes the carrier of ore particles, not only agrees with and is simulated by engineering mathematical models, but is statistically verified by actual laboratory flotation data. The model couples the mechanical removal of froth using paddles with the more rapid interactions taking place in the bath. It clearly shows that the kinetics of mass removal is dictated by flotation cell dimensions, paddle speed, and, more importantly, froth characteristics. Some conclusions and model predictions are presented.

Jan 1, 1984

By C. D. Keen

IN the latter part of the summer of 1913 the Conservation Commission of the State of Louisiana, under presidency of M. L. Alexander, decided to stop the waste of natural gas going on at the "burning gas-well," located about 3/4 mile southeast of Oil City, La. On several occasions, both in newspapers and in reports, comment had been made on the condition of this well, its harmful effect on the Caddo gas field, and the considerable loss, estimated at several thousand dollars each month, caused by the escape of the valuable fuel. But nothing had been done to bring the well under control and prevent further waste of gas until the State Conservation Commission took the matter in hand. The gas fields of Louisiana are among the greatest in the country. So far most of the gas has been found in the Caddo field proper, although considerable development has been done in and around the city of Shreveport and near the town of Mansfield in DeSoto parish. To extend the life of the gas fields and to prevent the quick exhaustion of the supply of the natural fuel are matters of vital importance for this section of the country. Four gas companies have entered the Caddo field and supply the surrounding towns and cities with gas. The Arkansas Natural Gas Co. has pipe lines to Little Rock, Ark., and supplies gas to the following cities and towns in that State: Texarkana, Hope, Garland, Emmet, Prescott, Boughton, Beirne, Gurdon, Arkadelphia, Gum Springs, Malvern, Donaldson, Gifford, Perla,- Beaton, Beauxite, Mabelvale, Bryant, Sheridan, Pine Bluff, Little Rock, Argenta, Pulaski Heights, and Hot Springs. The Southwestern Gas & Electric Co. transports gas to Mooringsport, Blanchard, Caddo, Rodessa, Oil City, Vivian, Bloomburg, Hosston, Ida, Dixie, Belcher, and Shreveport. The Marshall Gas Co. supplies gas to the town of Marshall, Texas. The Louisiana Co. has a line to Shreveport.

Jan 3, 1914

By A. Arrott, G. S. Ansell

A model is proposed to account for the observed strengthening behazlior of ferrous martensites. me model is based upon the inheritance of carbon-rich regions by the martensite which were present in the FERROUS martensite is formed by a nucleation and shear mechanism when austenite is cooled, at a rate which is fast enough to suppress the formation of pearlite, below a critical temperature (Ms ). Although the mechanism of the transformation process appears to be well understood,1,2 the mechanism re- austenite prior to transformation. These carbon-rich regions strengthen the martensite in a manner analogous to the strengthening effect due to a finely dispersed second phase. sponsible for the observed high strengths exhibited by ferrous martensites is uncertain. In this paper, a model is proposed to account for the strengthening of ferrous martensite. MODEL The maximum solubility of carbon in austenite is 1.98 wt pct as compared with a maximum solubility of 0.025 wt pct in ferrite. Prior to transformation, the carbon in the austenite is nonuniformly dis-

Jan 1, 1963

Jan 1, 1911