Search Documents

By Cornelius J. Dwyer

It is possible to hold a very optimistic view of the future of the U.S. coal industry, and there are those in the coal industry who generally choose to do so. For example, a major coal company stated recently in its annual report, "Coal's prospects appear brighter today than at any period in the past." In order to continue in this state of euphoria, it is only necessary to remind oneself of the following "facts":

Jan 7, 1967

By Bruce A. Kennedy, Richard M. Stewart

Slope stability has now become a practical tool in the design and operation of open pits. The selection of slope angles is a critical decision that can have far-reaching effects on the accumulated cash flow and the overall profitability of a mining project. Slope failures can now be dealt with in a number of ways. Two methods - the total removal and the partial unloading of a failing zone-have been practiced for many years. However, with the refinement of monitoring techniques, open pits can now learn to live with a slide and even turn a potential loss into a gain. There are various techniques, such as presplit blasting, drainage systems, and artificial stabilization, which can be applied immediately in an existing open pit to improve the stability of the pit slopes. The technology of slope stability will play an important part in the future mining of low grade, previously marginal orebodies, which will have to be exploited if the mineral needs of the world are to be met.

Jan 1, 1971

By Gerald A. Munson, Fremont F. Clarke

During recent years the use of lithium has expanded greatly in industrial, chemical, and metallurgical fields, while at the same time modernized methods of mining and refining lithium have increased production. Technical literature includes many papers describing the geology and mineralogy of lithium deposits. Mining and beneficiating problems, however, have not been thoroughly described. Published reports have failed to emphasize that one of the chief reasons lithium minerals were not extensively mined until recently is the difficulty of beneficiation. Four lithium minerals of pegmatites and the lithium-sodium-phosphate byproduct from the brines at Searles Lake, Calif., have been sources of lithium. Among the pegmatite minerals, only spodumene and petaline are known to occur in deposits large enough to support large tonnage operations. Spodumene, a lithium-aluminum-silicate, is the principal lithium mineral mined in the U. S.

Nov 1, 1955

By S. G. Malghan, A. L. Mular

Size distribution and surface area measurements play an important role in the characterization of crushed and ground granular materials properties. This paper outlines sampling methods of granular materials followed by a detailed treatment of principles of size and surface area measurements of a wide range of sizes from crushers feed to ball-mill ground sub-micron particles. Currently available equipment for size distribution and surface area analysis is described and critically examined with respect to advantages, range of application and precautions in their use. Equipment for on- stream size analysis is also evaluated. Finally, a list of criteria are given for selection of particles size and surface area measuring devices for a particular application.

Jan 1, 1982

Discussion of the papers of DAVID H. BROWNE, Louis V. BENDER, and R. E. H. POMEROY, presented at the New York meeting, February, 1915, and printed in Bulletin No. 97, January; 1915, pp. 49 to 60, 73 to 81, and No. 98, February, 1915, pp. 445 to 453, respectively. E. P. MATHEWSON, Anaconda, Mont.-After hearing about the success of D. H. Browne with his furnaces, we in Anaconda decided we might venture into the field of pulverized coal for reverberatory smelting. We sent a delegation of investigators to see Mr. Browne and his work, and they returned, filled with enthusiasm, and said they would recommend it strongly. We thereupon asked for an appropriation, and after some delay obtained the same and fitted up one furnace to use pulverized coal. We copied Mr. Browne's practice and his selection of machinery for drying and pulverizing coal; and we also copied the burner he used, which was a standard article on the market. We got an expert coal-dust machinery man to design our plant, and were very glad we did so as we avoided some of the unpleasantness that had been experienced at other plants through fires and minor explosions.

Jan 5, 1915

By Raymond Howe

SOME time ago,, a prominent engineer asked a representative of the firebrick industry to prepare a comprehensive paper on blast-furnace refractories. It was to have been the purpose of this paper to gather practical experiences from widely different sources, in the hope of determining what kind or kinds of firebrick were best adapted for certain uses. This engineer sent questionnaires to the large consumers of blast-furnace linings and stovebrick and received very detailed replies as to their experiences. These replies are conflicting, but, having been turned over to the writer, form the basis of this attempt to meet the request. Because of the impossibility of making final recommendations at this time, a few of the more interesting and commonly known methods of studying refractories are also discussed, as well as the more recent developments in this field. The first reply to, the questionnaire stated that good service was being secured from the linings. This satisfactory condition was attributed to the use of a very good distributor. The writer believed that manufacturers try to and do produce a good product and that the proper handling of equipment is of the utmost importance, if good results are to be secured. The type of bricks used was not mentioned. The second reply stated that good life was secured from the furnace linings, but that the writer had had soft-fired stovebrick crumble and, for that reason, preferred a hard-fired product for use in this position. The type of bricks used was not mentioned. The third reply stated that firebrick had crumbled from the mantle up; the cause was not known. The fourth reply stated that the stove linings were satisfactory. Hand-made furnace linings failed after 4 years' service so a steam-pressed lining was installed which was still good after 4 years of service. Consequently, a second steam-pressed lining was installed but this disintegrated at the top after the furnace had been in- blast 7 months. The firebrick manufacturer attributed this failure to the expansion of iron blocks that had been installed at the stock line to prevent erosion.

Jan 9, 1919

By d&apos, D. L. Guernsey, J. C. Entremont, John Chipman

The reaction of aluminum with oxygen in liquid iron has been studied at 1740° and 1910°C. Interaction coefficients are very much smaller than those previously published. The equilibrium constant falls within the approximate range of earlier experiments and calculations. It is now well established that the "deoxidation constant" for aluminum in liquid steel at normal steelmaking temperatures is extremely srnall. Thus at 1600 the product [% Al] is of the order of 10- 14. At this temperature, therefore, great experimental difficulties are encountered in any attempt to obtain a direct measure of the constant. If the aluminum content of the metal is high enough to permit accurate analytical determination, that of the oxygen is too low. If the oxygen content is high, the aluminum is below the limits of detection. Our best values of the constant have come, therefore, from indirect calculations or by extrapolation downward from observations at higher temperatures.. For their studies in the range 1695° to 1866°C, Gokcen and chipman' restricted their aluminum concentrations to less than 0.06 pct. Oxygen analyses were made by the vacuum fusion method which appears to be dependable at these low aluminum concentrations. Experimental results, even at the highest temperature employed, are extremely sensitive to small errors in the analysis of either element. The slight change in the equilibrium constant with aluminum and oxygen concentration was utilized in the calculation of interaction coefficients expressing the effect of aluminum on the activity coefficient of oxygen and the reciprocal effect of oxygen on the activity coefficient of aluminum. The range of concentration, however, was so limited that only a rough value for the interaction coefficient could be obtained. This value was much more negative than that found for any other pair of reactants. In view of the very limited range of concentration employed, the reported values have always been regarded as very questionable. A redetermination was the object of the work reported here. EXPERIMENTAL METHOD At high aluminum concentrations, the vacuum fusion method is susceptible to grave error due to absorption of gas by aluminum distilled from the sample. Since it was desirable to extend the study to at least as much as 1 pct Al, another method for analysis was sought. In steels containing more than a few hundredths of a percent aluminum and no other deoxidizing element, it is safe to assume that

Jan 1, 1963

By R. Woodward Moore

A GRAPHICAL method of analyzing the data obtained from shallow earth-resistivity depth tests is presented. The method is based upon empirical results and has no theoretical basis. The usual apparent resistivity-electrode spacing curve is used together with a cumulative resistivity-electrode spacing curve plotted on the same sheet. The greatly reduced scale required for plotting the cumulative values of resistivity together with the effect of the summation of the individual resistivity values serves to minimize the effect of purely local surface anomalies and inadvertent errors of measurement. The point of intersection of tangents or straight lines drawn to intersect at zones of maximum curvature in the cumulative curve indicates the depth to the underlying material. Numerous figures are presented in which data from published reports and from recent field studies are analyzed and the results compared with actual depths established by borings or with depth values obtained by the use of theoretical methods of analysis. Smoothly rounded curves of apparent resistivity such as are often obtained in the field, and which have been a serious drawback to attempts to analyze the data empirically heretofore, appear to be susceptible to rather accurate analysis by the method described. The method is best suited to analyses involving shallow two-layer formations. It has been applied successfully, however, in analyzing the data obtained from tests made over shallow three-layer formations. As with most empirical methods, its chief advantage is its simplicity and ease of application.

Jan 1, 1944

By C. Willard Hayes

One of the most productive iron-ore districts of the southern Appalachians lies in the vicinity of Cartersville, in northwestern Georgia, where the ore-deposits are so directly related to the stratigraphic and structural features of the region that a description of its geology possesses economic as well as scientific interest. Stratigraphy.—The area shown on the accompanying map, Fig. 1, occupies the southeastern portion of Bartow county, Georgia. It is about equally divided between the older crystalline and metamorphic rocks which occupy the Piedmont plateau and Appalachian mountains on the east, and the Paleozoic formations which occupy the Appalachian valley on the west. The line separating these two groups of formations enters the mapped area near the northeastern corner, and, pursuing a somewhat irregular diagonal course, leaves it, as shown on the map, near the southwestern corner. This line marks

Jan 1, 1901

By Fred Hale

OWING to the large area included in the Yellow Pine mining district, and the-varied nature of its mineral deposits, a detailed geological description of the district could be covered only in an extensive monograph. This paper is intended as a description of the most prominent geologic features only with special reference to those of economic importance. The first mention of the district was in 1903 by J. E. Spurr,1 who briefly describes the structural geology of the Spring Mountain range. In 1906, H. F. Bain2 briefly described the Potosi mine. James J. Hill,3 of the United States Geological Survey, visited the district for a brief period in 1912, the result of which is an excellent reconnaissance report, covering the district in some detail but necessarily with brevity. Since that time, articles covering special features of the district have appeared in the technical press, including some by the writer, and a notable description of the Boss mine, by Adolph Knopf,4 appeared in 1915. Development of the district during the past few years has progressed so rapidly and with so many notable discoveries, particularly with reference to the rare metals, that a further description at this time may prove of interest. The writer's acquaintance with the district is based on 7 years' continuous residence in the vicinity, beginning with the spring of 1910.

Jan 2, 1918

By Robert C. Emmett, Donald A. Dahlstrom

FOR many years gravitational classification has been employed as a basic tool in beneficiation of minerals and coal. While improvements have been made to increase efficiency and fields of application, the basic flow pattern has remained relatively unchanged in most gravitational classifiers. Feed slurry is introduced into a settling pool wherein the coarser solids settle against either an upward or horizontal fluid current, or a combination of both, and are withdrawn in a concentrated underflow stream. The finer solids below the classification point possess too low a settling velocity and thus are primarily swept out through a weir overflow by the bulk of the fluid. Because of its simplicity, efficiency, and low power and maintenance costs, gravitational classification finds a wide acceptance for separations in the range of 20 to 325 mesh. Two factors resulting from the basic flow pattern employed in gravitational classification present difficult problems for certain installations. If classification at 60 to 200 mesh of separation is desired, capacity in terms of gallons of overflow per minute per square foot of settling pool area must be low to allow required solids to settle to the underflow. If a thousand or more gal per min of feed slurry must be handled, either a very large classifier or a number of smaller units must be employed, taking up floor space and head room. Examples of this are the large classifiers, wetting tanks, or settling tanks used in the coal industry for recovery of process water from fine solids. Units as large as 50 or 60 ft in diam and 60 ft high, requiring substantial amounts of steel, are not uncommon. A second factor is the lack of self-regulation in gravitational classification. As overflow rate increases, mesh of separation increases correspond-ingly. This normally heightens difficulties of bene-ficiation. If a fine mesh of separation is required at varying feed rates, the problem is more than doubled in complexity. One of the primary advantages of gravitational classification is low power requirement. Gravity feeds or very low pressure heads are employed. However, fluid energy is still present in the inlet stream and provision must be made to dissipate it properly to obtain uniform upward or horizontal currents. Rather than waste this energy, it would be desirable to utilize it to secure a greater degree of self-regulation and simultaneously increase classification capacity per square foot of area. A free vortex could be realized by a tangential entry of feed, resulting in generation of centrifugal force to complement force of gravity in its action. With greater force it should be possible to gain finer separation at any overflow rate per square foot of settling pool area as compared with conventional gravitational classification. Furthermore, as feed rate increases, centrifugal force will also increase and at least partially offset faster currents sweeping solid particles to the overflow. A more stable classification point should result. The liquid-solid cyclone is the most common application of a free vortex in the beneficiation field.' Many previous papers have emphasized uniformity of flow pattern within the cyclone which is largely responsible for the sharp classification that can be obtained.'-4 If a free vortex can be maintained in a non-pressurized vessel with a free surface it may be possible to realize a third advantage of sharper classification. This open-top cyclone would then achieve a minimum energy loss comparable to that with conventional classifiers, and a mesh of separation coarser than 150 mesh, extending the range of application of the free vortex. This is not presently possible with ordinary cyclones. To test the applicability of the free vortex to gravitational classification, a 30-in. diameter open-top cyclone was constructed at Northwestern University. The cylindrical section was 30 in. high and the conical section included an angle of 60". The feed nozzle was a standard 4-in. pipe entering tan-gentially, with centerline 17 1/2 in. below the top of the cyclone. The conical section was flanged near

Jan 1, 1954

By M. R. Geer, H. F. Yancey

INTRODUCTION The maximum yield of washed coal and the required ash and sulfur contents are the only performance factors of direct, immediate interest to any operator. Yet since the turn of the century coal preparation engineers have repeatedly sought more sophisticated performance criteria that could be used to draw comparisons between different cleaning operations and to permit generalizations about types of cleaning equipment or kinds of coal. Proliferation of efficiency formulas resulted. Hardly a year goes by, and certainly not an International Coal Preparation Congress, without the introduction of some new formula or some new concept of an existing criterion. This is merely the usual quest for improvement, because the performance criteria available today, although highly useful, are imperfect. Moreover, they are not as widely understood as they might be. The First International Coal Preparation Conference, which was held in Paris in 1950, accomplished a great deal toward establishing uniformity in terminology and methods of expressing cleaning results; the proceedings of that conference provide a wealth of detailed information on the various performance criteria, their uses and their limitations. For ease of discussion, the various performance criteria can conveniently be classed according to the degree to which they are dependent on the density composition of the raw coal treated. Some are directly dependent, some are only indirectly dependent, and some are, under certain circum- stances, essentially independent. DEPENDENT CRITERIA The yield and ash content of a washed coal are directly dependent on the washability characteristics of the raw coal from which it is derived. Thus, they are manifestly unsuited to comparing the performance of different plants, because no two plant feeds are the same. In fact, yield and ash content, by themselves, are inadequate for even routine day-to-day control. The continuous variation that occurs in the amount of impurity in raw coal, and sometimes in the float ash, make it impossible to tell whether a reduction in yield or an increase in the ash content of the washed coal results from any malfunction or misadjustment of the cleaning equipment. Recovery Efficiency For many years the most popular performance criteria that are only indirectly dependent on the washability characteristics of the raw coal have been efficiency formulas. Of the many that have been proposed, the one advanced by Fraser and Yancey in 1923 has had the widest accept-

Jan 1, 1968

Jan 1, 1917

By R. C. Buehl, J. P. Riott, E. P. Shoub

PILOT-PLANT tests have demonstrated that it is possible to produce low-sulphur sponge iron (0.03 to 0.05 per cent sulphur) as a continuous process in an internally fired rotary kiln from iron ore or mill scale; a solid carbonaceous reducing agent; and dolomite to control the sulphur content. The proportion of dolomite employed is small, so that it does not add materially to the cost of the sponge iron. The entire operation is carried out at temperatures well below the melting point of iron, so that the product is discharged in granular form. Compared with other methods for the production of sponge iron, the rotary-kiln method has the advantage of simplicity and low cost of equipment and; in addition, requires little labor for the operation of the process. The pilot-plant equipment used for this work was sufficiently large to demonstrate that the production of low-sulphur sponge iron in rotary kilns is feasible and that the costs are not excessive for applications in which sponge iron has distinct advantages over competing materials. This report constitutes a part of a program by the Bureau of Mines under a special Congressional appropriation for studying gaseous and solid fuel reduction of iron ores. Numerous articles on various phases of these investigations have appeared in Bureau of Mines publications or technical journals. Other articles are being prepared and will be published in the near future. The present program, which is under the supervision of Dr. R. S. Dean, Assistant Director of the Bureau of Mines, was initiated in .1942. However, a considerable portion of the work was a continuation of previous research performed by the Bureau. Previous investigators1-4 utilizing the rotary kiln for the production of sponge iron did not develop a suitable method for controlling the sulphur content. A review of the literature shows that the sulphur content in the product usually exceeded 0.2 -per cent unless reducing agents with very low sulphur contents were employed. This high sulphur value made the product generally undesirable for use as melting stock in electric or open-hearth furnaces. The production of sponge iron in an internally fired rotary kiln has been described in detail in Bureau of Mines Bulletin 2702; consequently, this article will be confined mostly to new features of the process-that is, means for controlling the sulphur content of the sponge iron. Suitable raw materials include iron ores or mill scale; coal or coke for reducing them, and sized dolomite (-20+100-mesh) as the sulphur-controlling agent. A mixture of the raw materials in granular form is fed into the elevated end of the kiln, which is fired axially from the lower or discharge end. In the reducing zone, which is approximately one third the length of the kiln measured from the dis-

Jan 1, 1946

By J. E. Kemp

1. Situation.—From Monterey in the State of Nuevo Leon, the Sierra Madre mountains stretch away to the southeast and present a steep front to the northeast. The Monterey and Mexican Gulf railway. which connects Monterey with Tampico. follows their general line with its road-bed a few miles out from the foothills. At a distance of 100 miles from Monterey it passes through the town of Linares. and from Linares one can see far away to the southeast the peaks of another group of mountains rising from the general plateau and forming a more eastern

Jan 1, 1906

By Richard Moldenke

One of the gravest problems of the iron foundry today is the accumulation of sulfur in commercial scrap and its effect on the castings made therewith. The ordinary jobbing castings today show a sulfur content of 0.18 per cent;, and occasionally as high as 0.22 per cent. The product of the foundry during the war is undoubtedly to blame for this rapid increase and conditions will become worse as the millions of tons of gray-iron castings of the war period return to the foundry in the form of commercial scrap. In the ordinary cupola remelting of pig and scrap, at least 0.02 per cent. sulfur is taken up; often double that amount. The high cost and difficulty of obtaining pig iron during the war period compelled the use of considerable scrap in the mixtures; frequently charges containing 90 per cent. of bought scrap were melted. Naturally the sulfur content of the castings increased. Until the advent of the basic-hearth electric furnace, the only method of holding the sulfur within reasonable limits was to use high percentages of pig in the foundry mixtures. Pig iron seldom contains over 0.05 per cent. sulfur, if well made. With pig iron forming 60 per cent. of the charge and the gates, runners, rejections, and bought scrap the other 40 per cent., the sulfur content of the castings can easily be held down to 0.10 per cent. Pig iron, however, costs more than scrap even when melting loss differences are considered, hence as small a percentage as possible will be used. The recent advance in knowledge of rational melting and the consequent reduction in losses directly due to oxidation of the metal and cold iron, has permitted the acceptance of castings with a much higher sulfur content than formerly. The steel industry also is seeking to determine how high sulfur may go with safety. In the iron foundry, however, there is the danger of a low cupola bed or an unduly retarded air-furnace heat, with the consequent raising of the freezing point of the metal and segregation effects resulting from high sulfur with insufficient manganese. The iron foundryman must, therefore, have a means of correcting his

Jan 1, 1922

By Richard Moldenke

One of the gravest problems of the iron foundry today is the accumulation of sulfur in commercial scrap and its effect on the castings made therewith. The ordinary jobbing castings today show a sulfur content of 0.18 per cent;, and occasionally as high as 0.22 per cent. The product of the foundry during the war is undoubtedly to blame for this rapid increase and conditions will become worse as the millions of tons of gray-iron castings of the war period return to the foundry in the form of commercial scrap. In the ordinary cupola remelting of pig and scrap, at least 0.02 per cent. sulfur is taken up; often double that amount. The high cost and difficulty of obtaining pig iron during the war period compelled the use of considerable scrap in the mixtures; frequently charges containing 90 per cent. of bought scrap were melted. Naturally the sulfur content of the castings increased. Until the advent of the basic-hearth electric furnace, the only method of holding the sulfur within reasonable limits was to use high percentages of pig in the foundry mixtures. Pig iron seldom contains over 0.05 per cent. sulfur, if well made. With pig iron forming 60 per cent. of the charge and the gates, runners, rejections, and bought scrap the other 40 per cent., the sulfur content of the castings can easily be held down to 0.10 per cent. Pig iron, however, costs more than scrap even when melting loss differences are considered, hence as small a percentage as possible will be used. The recent advance in knowledge of rational melting and the consequent reduction in losses directly due to oxidation of the metal and cold iron, has permitted the acceptance of castings with a much higher sulfur content than formerly. The steel industry also is seeking to determine how high sulfur may go with safety. In the iron foundry, however, there is the danger of a low cupola bed or an unduly retarded air-furnace heat, with the consequent raising of the freezing point of the metal and segregation effects resulting from high sulfur with insufficient manganese. The iron foundryman must, therefore, have a means of correcting his

Jan 1, 1922

By Portland P. Fox, Berlin C. Moneymaker

THE development, within recent years, of core drills capable of drilling holes up to 72 in., or even more, in diameter, has made possible an entirely new and valuable method of geologic exploration. Although little used until recently as an exploratory tool except in the United States, by the Tennessee Valley Authority and the Corps of Engineers of the U. S. Army, for the exploration of damsites, the large-diameter core drill may be used to good advantage in other types of geologic exploration. Its principal utility is that of supplementing, rather than replacing, other means of exploration. Although core is frequently recovered intact, the greatest advantage of large-diameter drilling is that the holes produced are large enough to be entered by the geologist and engineer, and thus afford an excellent means of examining undisturbed rock. The walls of the holes are smoothly cut, and in some rocks nearly or quite polished, so that the most minute details of structure and stratigraphy are clearly disclosed. Such features as faults, joints, bedding planes, weathered "seams," and beds or layers of soft materials, which are not always amenable to disclosure by cores recovered from small-diameter holes, are conspicuously displayed in the walls of large holes. Frequent reference to the drilling of large-diameter holes is made in engineering literature, but comparatively little emphasis has been placed on their value in geologic investigation. It is, therefore, intended that the present paper acquaint the geologist, as well as the engineer, with the large-diameter core drill and the technique involved in its use, and also with its advantages, disadvantages and limitations as an implement of geologic exploration. THE EQUIPMENT The equipment generally employed in the drilling of large-diameter holes consists of a trunnion-type drill head mounted on a sliding base, which allows it to slide clear of the hole and thus permit the introduction

Jan 1, 1938

By J. K. Gustafson

MEASURED in terms of ore tonnage, the New Quebec and Labrador iron ore fields promise to rank with the greatest iron ore districts of the world. -- Over 400 million tons of high-grade ore for direct shipping have been discovered to date. Much greater amounts of lower-grade beneficiating ores are indicated by outcrops. Many hundreds of square miles of iron formation await testing.

Jan 6, 1953

By Karl Sundberg

INTERESTING results were recently obtained in geophysical prospecting at the Questa mine of the Molybdenum Corpn. of America in New Mexico. This paper describes that survey, which was carried out during October and November, 1927, by the Swedish American Prospecting Corpn. It is hoped that the paper will make it possible for the mining man to form an opinion of the applicability of geophysical prospecting under difficult conditions, showing, as it does, the results when prospecting for small small orebodies with comparatively poor conductivity, in a region of rough topography. Some principles underlying electromagnetic prospecting not known to be published previously will also be given in an elementary way, with special attention to the general structure of the electromagnetic field. GEOLOGICAL CONDITIONS AT QUESTA The property is situated in the Taos range of the Rocky Mountains in northern New Mexico. About this region, L. C. Graton says:1 The main range is made up of pre-Cambrian granites, gneisses and schists but in the vicinity of Red River igneous rocks of later age are present almost to the exclusion of the older series. These younger rocks are divisible into two groups. The older of the two, probably pre-Tertiary age, is represented by large intrusive masses of monzonite porphyry, usually containing considerable quartz. The more recent group comprises intrusive' and probably effusive dark-colored andesites and coarse andesitic breccias, some of which contain fragments of the monzonite; there are also flows of rhyolite and beds of rhyolite breccia. The evidence regarding the relative age of the andesite and the rhyolite is not wholly satisfactory, but there is little doubt that the andesite is the older. The ore deposits, although occurring more commonly in the monzonite porphyry than in the rhyolite, nevertheless are believed to be genetically related to the rhyolite. They certainly cut the rhyolite or andesite in places, and hence fall in the late Tertiary.

Jan 1, 1928