Search Documents

By Ernest A. Hersam

The advantages of the tri-axial diagram in representing the composition of slags and silicates are well appreciated by many metallurgists. Prof. H. M. Howe* has pointed out the application of a fourth variable, in connection with the diagram, and has called attention to the usefulness of the general systern of tri-axial representation. In the discussion of Prof. Howe's paper, Mr. Firmstone† indicated how certain distances could be measured directly by projection. Prof. R. H. Thurston,‡ as early as 1877, had made use of a typtic model and of triangular diagrams, with contour-lines, rekrresenting varying physical properties corresponding to varying chemical composition. Still earlier, Prof. J. Willard Gibbs§ had used the diagram in similar work; and other scientists were thought by him to have preceded him in its use. During the period of nearly a quarter-century, following these early publications, there has been an ever-increasing use of graphic methods in numerous branches of scientific work, stimulated, in part, by the possibility of representation by three co-ordinates upon plane-surfaces. Yet the number of possible co-ordinates for graphic representation has always been, and always must be, insufficient to express many facts which are shown mathematically; while, without graphic representation, the involved nature of mathematical expression often fails to facilitate and promote research. The coming into use, therefore, of the fourth co-ordinate, permitting representation by four variables, marks but the beginning of some lines of research which could not well advance without this aid.

Jan 1, 1902

By M. Stern, I. S. Servi, W. W. Webb

ZINC has been considered an ideal material for investigations of the behavior of dislocation walls in metals. It has appeared particularly useful for studies of the mechanisms of plastic deformation and the motion of low-angle boundaries under stress, because orientated crystals are easily grown and cleaved. Moreover, the hexagonal structure makes the introduction of controlled tilt boundaries relatively simple. Apparently, another of the many reasons for selecting zinc as a working material is its commercial availability at the 99.999' pct purity level. However, most elements are only slightly sol-

Jan 1, 1959

By E. P. Peleider

DIAMOND drill research work was initiated at the School of Mines, University of Minnesota, in late 1949. The Drilling Symposium held in Duluth that spring highlighted the problem of high cost and core recovery and the need for controlled testing. An advisory committee made up of informed representatives of both mining companies and drilling companies was formed to suggest and advise on a program of drill research. A Hy-Mac hydraulic drill unit, see Fig. 1, especially designed for experimental testing, was obtained for this work by the School of Mines through the courtesy of the Carboloy Co. It is an extremely flexible unit, capable of exerting a forward thrust of about 1750 lb and turning at speeds from 650 to 2200 rpm. The feed arrangement is so designed that the advance can be set either at a constant rate or permitted to vary at a fixed Pressure, see Fig. 2. The

Jan 1, 1953

By E. P. Peleider

DIAMOND drill research work was initiated at the School of Mines, University of Minnesota, in late 1949. The Drilling Symposium held in Duluth that spring highlighted the problem of high cost and core recovery and the need for controlled testing. An advisory committee made up of informed representatives of both mining companies and drilling companies was formed to suggest and advise on a program of drill research. A Hy-Mac hydraulic drill unit, see Fig. 1, especially designed for experimental testing, was obtained for this work by the School of Mines through the courtesy of the Carboloy Co. It is an extremely flexible unit, capable of exerting a forward thrust of about 1750 lb and turning at speeds from 650 to 2200 rpm. The feed arrangement is so designed that the advance can be set either at a constant rate or permitted to vary at a fixed Pressure, see Fig. 2. The

Jan 1, 1953

By Carl Thieme

INDUSTRIAL specialization has rapidly created a demand for new and better alloys. A more thorough understanding of the requirements of specific industries and the discovery of processes by which it has been made possible to utilize certain metallic elements in larger quantities, together with greater purity in most virgin metals, has resulted in a great increase in the number and variety of alloys. This increase in the number of elements entering into non-ferrous alloy manufacture has increased the contamination in secondary metals, as received by the smelter. In order to successfully refine scrap of a much more complex nature it has been necessary for the smelter to install new equipment and to constantly search for new methods of refining as well as to improve the methods already in use. In some instances it is largely responsible for specialization in the secondary metal industry. It is usually necessary to remove the contaminating impurities in scrap or eliminate to a degree not objectionable, no matter how introduced. In order to know what metals or elements are of an objectionable nature, the smelter must make a study of the effect of single elements and combinations of elements on many of the physical and mechanical properties, such as strength, ductility, color, hardness, casting soundness, etc. The smelter of secondary metals must be able to utilize scrap materials of all kinds, for, sooner or later, most fabricated metal parts and the waste products formed during the process of manufacture find their way to the smelter. In addition, the smelter, in contracting for salvaged material from the producer, gets some undesirable and unusual materials. The value of secondary metals and the importance of their recovery has increased in recent years and it is no longer sufficient to recover the base metal only, such as copper from copper-bearing material, but it is essential that other elements present be recovered and converted into useful form.

Jan 1, 1928

By C. C. Henning

IN any line of human activity logical handling requires an amount of attention to each phase that is in keeping with the importance of that phase. In the complex and rapidly changing field of modern ferrous metallurgy it is difficult to allot the proper degree of attention to the various subjects, and it is not surprising that one or more subjects of major importance should for a time be neglected. Bessemer steel is a good example of a neglected subject. It is largely taken for granted, inferior physical quality is assumed for it, and there is a lack of interest in its technical development and commercial application. Availability of supply is limited. In spite of this technical indifference, limited source and lack of commercial exploitation, bessemer steel constitutes a large volume of tonnage in daily use. There is a fairly prevalent idea even among technical people that bessemer steel survives mostly because of low cost and by reason of a dwindling residue of applications sufficiently common to permit of its use. The difference in cost between bessemer and open-hearth steel is governed largely by the relative cost of manufacture of pig iron and the market price of steel scrap. During the past four years there have been long periods of time during which the price of steel scrap was low enough so that open-hearth steel was considerably lower in manufacturing cost than bessemer. As to application, it may be pointed out that thousands of tons of this material in the form of bessemer screw steel are applied for moving parts in automotive and other equipment, Some forging work and considerable heat treating, particularly carburizing, is performed on this grade. From an economic standpoint the most effective contribution of bessemer steel lies in its free machining qualities. It is by far the freest

Jan 1, 1935

By F. C. Schora, H. P. Meissner

COUNTERCURRENT staged processes involving chemical reactions between solid and gas streams are becoming more common. Such operations are generally carried out in a series of fluidized beds with each bed acting as a stage. Fig. 1 is a schematic illustration of a series of stages located in a single column, with a solid stream moving down through this column from stage to stage counter to a rising gas stream. The reduction of iron oxides with hydrogen and carbon monoxide is one of the reactions which can be advantageously carried out in such a countercurrent system. Calculation of the performance of a countercur-

Jan 1, 1961

By E. S. Machlin

The alternate processes by which solute atoms can limit the migration of grain boundaries have been considered. At the lowest solute concentrations the controlling process is "mechanical breakaway" in which the solute atoms affect the driving force and not the mobility. In the next higher range of solute concentration, solute atoms are bound to the boundary and diffuse by boundary diffusion along cusps in the boundary developed at the solute atoms. In this region the boundary velocity is controlled by the component in the direction of boundary migration of the rate at which the bound solute atoms can diffuse along the boundary. At still higher concentrations, it is predicted that boundaries break away from the binding solute atoms by thermal activation. The specific behavior Predicted is consistent with the observations of Aust and Rutter. The most striking agreement between prediction and experiment is that obtained for a range of solute concentration in which the boundary velocity is inversely proportional to the cube power of the solute concentration. MaNY models have been devised for the atomic steps in the motion of a grain boundary. McLean1 has listed some of these models and Aust and utter' have evaluated these and other models. If there are

Jan 1, 1962

By A. H. Lindley, R. Shorr, Frazier M. Stewart, F. Crerie

The mineral industry, so important to industrial development, faces a major challenge in creating the most effective financial structure to provide funds essential for seeking, evaluating, developing, and extracting minerals. The acquisition of funds for mineral development and plant erection do not differ greatly from fund-raising in nonmineral ventures because risks are essentially comparable. High-risk exploration funds, however, are more difficult for the mineral industry to acquire. With the world's ever-increasing appetite for minerals, the internally generated cash of major oil and mining companies cannot be expected solely to maintain the world's mineral supply. The augmented costs, risks, and difficulties of exploration have been shared increasingly by the smaller independent operator and by private and public participation drilling programs within the petroleum industry over the past 30 years. Only recently has the mining industry awakened to the need for utilizing exploration and development funds derived from sources other than established mining and banking circles. Almost from its inception, the oil industry was forced to drill deep holes through overburden without the aid of a mineral "outcropping" which required geological, and in subsequent years, geophysical interpretation. The poorly financed, nontechnical prospector, who depended on a mineral outcrop, was not to play an important role in oil exploration as he did in mining. Because of the high cost of drilling and the demands for technical judgment to locate an exploration drill hole, corporate and sophisticated private funds generally financed oil discoveries. When external funds were subsequently required, these financially sophisticated explorers would turn to the banking community from which came numerous ingenious innovations, taking cognizance of existing tax laws. Like the oil explorer, the miner is now faced with probing below the surface, relying solely on regional geology and geophysical anomalies. The day is gone, for practical purposes, when the prospector discovers a deposit from a mineral outcrop. There is little doubt that the mining industry will now follow the course taken by the petroleum industry in acquiring external funds if it is to meet the future raw material requirements of the world. The oil industry has been able to attract bank funds more readily than the mining industry after a mineral discovery has been made because: (1) with few exceptions, an oil discovery can be placed into commercial production and will generate cash at much less expense and time than a mine; and (2) generally, costs of oil production, the value

Jan 1, 1976

By A. F. Nylander, J. H. Jensen

Magnesium, in its combined forms, is the sixth most abundant element and the third most abundant metal in the earth's crust, but it is so reactive that it is never found in nature in the elemental state. As part of the rock-forming minerals like magnesite, dolomite, olivine, and serpentine, it is combined in virtually insoluble forms. As part of soluble minerals like kainite (KC1 MgS04 - 3H20), leonite (K2S0, MgSO, 4H20), langbeinite (K,SO, 2MgS04), and carnallite (KC1 . MgCl? 6H20), it is found in evaporite deposits, generally of marine origin, deep within the earth's crust. Since these minerals are soluble, they are found only in deposits protected from the percolation and leaching action of ground waters by an insoluble and impermeable mantle. Usually this mantle is from several hundred to many thousands of feet thick. Finally, as a solute in marine-like brines, magnesium is common in surface and subterranean waters throughout the world. The oceans, which contain 0.13% Mg, illustrate the inexhaustible nature of the reserve. The recovery of magnesium from the rock-forming minerals, usually by thermal decomposition, and from dilute brines such as sea water by precipitation with lime, are frequent industrial practices. But the recovery of magnesium as magnesium chloride from evaporites or natural brines of concentration greater than sea water has been of little industrial significance for economic and technological reasons. The present US capacity is preponderantly based on the sea-water magnesia process with thermal reduction capacity in second place. No present magnesium capacity is dependent on recovery from the stronger natural brines. But projected capacity, although still weighted in favor of the sea-water magnesia process, is partly based on the recovery of magnesium chloride as a byproduct of potash operations.

Jan 11, 1964

By J. O. Lewis

The operation of gas-condensate fields is comparatively new and involves physical principles with which the industry was not prcviously familiar. It has been necessary to devise methods for testing gas-condensate wells and to correlate laboratory and field data. In this paper new methods are advanced for interpreting well G.P.M.† tests whereby dilution by dry gas can be estimated and information supplied on revaporization of condensates by dry gas. Inaccuracies in well test data are discussed. Changes in flow rates can cause changes in the G.P.M. of the effluent and it may take some time for a well to become stabilized after an important change in flow rate. Retrograde tests as usually conducted cannot be directly compared with field G.P.M. data, because the retrograde tests usually include solution gas in the condensates, which are reported On the cumulative basis whereas field data (G.P.M.) usually report pentaneS PlUS on a rate or instantaneous basis. Introduction Though long known to physicists, the phenomena Of retrograde condensation became known to the oil and gas industry Only in recent years, when deeper drilling disclosed that the behavior of vapors under changing pressures was different in high-pressure reservoirs than under the low-pressure operations with which the industry was familiar. These deep, high-pressure reservoirs in which condensation and vaporization behaved inversely to the accustomed manner became known as "gas-distillate," or preferably "gas-condensate" fields. Partly to prevent precipitation and retention of liquids in the reservoir, but still more to prevent the waste of residue gas, the operation known as "recycling," or preferably "cycling," was instituted, in which the residue gas is reinjected into the reservoir, thus maintaining pressure and driving the wet gas to the producing wells. For lack of field experience to serve as a guide, the industry had to assume that theory and laboratory experiments could accurately forecast retrograde behaviors in operating these gas-condensate fields, but it is obvious that these assumptions should be checked at the first opportunities against actual field experience. To make such checks, it is necessary to accumulate a large quantity of reliable field data, but experience has shown that it is difficult to obtain reliable field data and that the laboratory data as usually presented are not in directly comparable form. The problems of correlation involve the complex phase behavior on the one hand, and a knowledge of field data and a visualization of underground conditions on the other hand. This paper is an approach from field experience, The purposes of this article are to discuss the sources of uncertainty in the data and to present methods of analyzing, interpreting and correlating laboratory and field data. Data mostly from lower Gulf Coast fields are presented, from which some conclusions can be derived, but better data from more sources than those available to the writer will be required before satisfactory answers to many questions can be obtained. This paper is presented to stimulate the analysis and publication of data from other fields, the reexamination of field and laboratory methods, and the taking of more complete and reliable field tests. For these purposes, the writer presents some speculations that otherwise would not be appropriate.

Jan 1, 1947

By J. O. Lewis

The operation of gas-condensate fields is comparatively new and involves physical principles with which the industry was not prcviously familiar. It has been necessary to devise methods for testing gas-condensate wells and to correlate laboratory and field data. In this paper new methods are advanced for interpreting well G.P.M.† tests whereby dilution by dry gas can be estimated and information supplied on revaporization of condensates by dry gas. Inaccuracies in well test data are discussed. Changes in flow rates can cause changes in the G.P.M. of the effluent and it may take some time for a well to become stabilized after an important change in flow rate. Retrograde tests as usually conducted cannot be directly compared with field G.P.M. data, because the retrograde tests usually include solution gas in the condensates, which are reported On the cumulative basis whereas field data (G.P.M.) usually report pentaneS PlUS on a rate or instantaneous basis. Introduction Though long known to physicists, the phenomena Of retrograde condensation became known to the oil and gas industry Only in recent years, when deeper drilling disclosed that the behavior of vapors under changing pressures was different in high-pressure reservoirs than under the low-pressure operations with which the industry was familiar. These deep, high-pressure reservoirs in which condensation and vaporization behaved inversely to the accustomed manner became known as "gas-distillate," or preferably "gas-condensate" fields. Partly to prevent precipitation and retention of liquids in the reservoir, but still more to prevent the waste of residue gas, the operation known as "recycling," or preferably "cycling," was instituted, in which the residue gas is reinjected into the reservoir, thus maintaining pressure and driving the wet gas to the producing wells. For lack of field experience to serve as a guide, the industry had to assume that theory and laboratory experiments could accurately forecast retrograde behaviors in operating these gas-condensate fields, but it is obvious that these assumptions should be checked at the first opportunities against actual field experience. To make such checks, it is necessary to accumulate a large quantity of reliable field data, but experience has shown that it is difficult to obtain reliable field data and that the laboratory data as usually presented are not in directly comparable form. The problems of correlation involve the complex phase behavior on the one hand, and a knowledge of field data and a visualization of underground conditions on the other hand. This paper is an approach from field experience, The purposes of this article are to discuss the sources of uncertainty in the data and to present methods of analyzing, interpreting and correlating laboratory and field data. Data mostly from lower Gulf Coast fields are presented, from which some conclusions can be derived, but better data from more sources than those available to the writer will be required before satisfactory answers to many questions can be obtained. This paper is presented to stimulate the analysis and publication of data from other fields, the reexamination of field and laboratory methods, and the taking of more complete and reliable field tests. For these purposes, the writer presents some speculations that otherwise would not be appropriate.

Jan 1, 1947

By Elmer W., Pehrson

NOT much serious consideration was liven to the military aspects of raw materials before World War 1. Following the outbreak of war in Europe in 1914, however. this situation was promptly changed. Disruption of allied shipping and German submarine warfare soon cut off a substantial part of the material the United Staten was accustomed to receiving from overseas. At the same time, raw material requirements rose rapidly as the tempo of industrial preparedness was stepped up in anticipation of war. By April 1917, when we entered the war, serious shortages threatened and consideralde attention was being given to our "deficcient" raw materials. The term "war mineral," began to appear after we became active combatants. But there is no evidence that "strategics" and "critical." as now used, had entered the lexicon of our raw materials experts during the last war nor were there apparently any officially recog¬nized list or definitions of what con¬stituted war materials. According to G. A. Roush in his book, `'Strategic Mineral Supplies," C. K. Leith, while serving as mineral advisor to the War Industries Board. compiled the first unofficial list of deficient minerals in 1917.

Jan 1, 1944

By R. P. McLaughlin

EXACT information as to performance of the gas lift from the mechanical engineering standpoint is hard to obtain. Several hundred wells are now producing in California fields by means of the gas lift, and a survey of results shows that the gas lift has increased production at these wells by approximately 60 percent. Similar or even larger figures describe results in Mid-Continent fields. Such an increase in output of oil is so satisfactory, to the average oil producer, that it may not encourage investigation looking to more efficient operation. The cost of lifting oil by compressed gas varies from 3 c. to 15 c. per bbl. of oil, depending upon the efficiency of the gas lift. A difference of 10 c. or 12 c. per bbl. of oil is immediately noticed by an oil operator and the cost in production is as real to him as is the price of his product. Therefore, the efficiency of gas-lift process deserves more consideration than it has been given in some quarters. It has been found that there is a wide variation between different operators and at different wells in the amount of gas used per barrel of oil lifted. Some of the most efficient operations show oil being lifted with only slightly over 400 cu. ft. of gas per bbl. of oil.1 On the other hand, wells are being flowed and using as high as 3000 cu. ft. per bbl. of oil. The cost of compressing gas to 300 or 400 lb. varies from 3 c. to 5 c. per 1000 cu. ft. of free gas. This figure has been obtained from a number of sources and as a matter of fact is the basis of actual business transactions involving gas compression. The cost of lifting oil with compressed gas is thus determined.

Jan 12, 1926

By R. H. Thorpe

Longwall working in Britain developed to overcome problems arising from depth of seams causing roof and ventilation difficulties. This system became very widespread particularly in the thicker seams, where faces of up to one mile in length were not uncommon. In the thinner sections, in order to remain competitive, the longwall undercutting machine was developed. Following the development of the coal cutter, every other aspect of the face operation was examined and mechanized as it became a bottleneck to output and efficiency. The face system itself was modified and workings concentrated with the same objectives.

Jan 1, 1977

By Zay Jeffries

IN this paper, it is proposed to outline a method for the determination of melting points of those metals and alloys having high fusion temperatures. The application of the method as used to determine the melting points of alloys of tungsten and molybdenum will be given. It will be seen from these results that tungsten and molybdenum form a completely FIG. 1.-PARTIAL SECTION OF APPARATUS USED TO DETERMINE MELTING POINTS OF TUNGSTEN AND MOLYBDENUM ALLOYS. isomorphous series. This is also verified by the accompanying photomicrographs. Tungsten and molybdenum have been found to crystallize in the salve system, namely, isometric, and the crystal units are cubes. These determinations were made by examining etching pits in the pure metals.

Jan 7, 1916

By Ancel St. John

At the New York meeting of the Institute of Metals Division in February, 1927, Jeffries and Tarasov presented a paper on Tungsten and Thoria,' in which the experimental facts were interpreted in accordance with the prevailing point of view that the thorium is present as the oxide, thoria. In discussing that paper the writer of this article stated that his own investigations, which had been unavailable to Messrs. Jeffries and Tarasov, showed that the so-called "thoriated" tungsten filament failed to disclose any sign of the oxide when subjected to X-ray diffraction analysis, but did give plenty of evidence of the presence of metallic thorium and, in certain cases, of a material believed to be an alloy of tungsten in thorium. Since these results were completely at variance with the results reported in the paper under discussion and with other papcrs which had preceded it from time to time in the past, it was felt that further discussion should be withheld until the new evidence could be presented adequately. Arrangc-mcnts were therefore made to present that evidence at this meeting. Material Examined The material exalllined was high-ernission filament such as is used in radio tubes, supposed to contain about 0.75 per cent. thoria. The actual analysis was not stated. Scope of the Investigation The investigation was undertaken because of a feeling that the thorium present in filamentary material of this type exists as metallic thorium or as an alloy of thorium and tungsten and not as the oxide. Attention was therefore directed to determining: 1. The minimum amount of thoria detectible in a mechanical mixture of thoria powder and finely divided tungsten. 2. The amount of t.horia detectible in the filament. 3. The condition of any thorium present in other form than as thoria. 4. The amount of thorium dissolved in the tungsten.

By W. E. Forsythe

Different forms of optical pyrometers are discussed and the advantages and disadvantages of the different types for measuring high temperatures are pointed out. These advantages and disadvantages lead to the selection of the disappearing-filament type of optical pyrometer for most work. Attention is directed to the necessity for the use of a monochromatic screen with a pyrometer, which leads to a discussion of the meaning and use of the effective wave length of the screen. Methods of calibrating the optical pyrometer are outlined and it is shown that an optical pyrometer can be calibrated just as definitely as any other temperature-measuring device. Accuracy tests are included, in which it is shown that excellent results can be obtained by even untrained or slightly trained observers with this form of optical pyrometer. The various corrections that are necessary in this kind of work are indicated, including corrections for stray light, for absorption of windows, of smoke, and so forth. The troublesome problem of measuring the temperature of bodies that do not radiate like a black body is discussed and the corrections for reducing such readings to the true temperature are given for a number of different materials. Introduction The fundamental idea of temperature depends upon our temperature sense and bodies are said to be hot or cold depending upon the reaction of our hands or some other part of the body to the heat from the source investigated. For measuring the temperature some instrument must be devised, since the temperature of the source studied is apt to be so hot as to greatly injure any part of the body that comes near it, to say nothing about direct contact with it. Definition of Temperature.—The temperature scale is based upon two fixed points, the temperature of freezing water and the temperature of boiling water. This temperature interval, depending upon the scale

Jan 1, 1936

By W. E. Forsythe

Different forms of optical pyrometers are discussed and the advantages and disadvantages of the different types for measuring high temperatures are pointed out. These advantages and disadvantages lead to the selection of the disappearing-filament type of optical pyrometer for most work. Attention is directed to the necessity for the use of a monochromatic screen with a pyrometer, which leads to a discussion of the meaning and use of the effective wave length of the screen. Methods of calibrating the optical pyrometer are outlined and it is shown that an optical pyrometer can be calibrated just as definitely as any other temperature-measuring device. Accuracy tests are included, in which it is shown that excellent results can be obtained by even untrained or slightly trained observers with this form of optical pyrometer. The various corrections that are necessary in this kind of work are indicated, including corrections for stray light, for absorption of windows, of smoke, and so forth. The troublesome problem of measuring the temperature of bodies that do not radiate like a black body is discussed and the corrections for reducing such readings to the true temperature are given for a number of different materials. Introduction The fundamental idea of temperature depends upon our temperature sense and bodies are said to be hot or cold depending upon the reaction of our hands or some other part of the body to the heat from the source investigated. For measuring the temperature some instrument must be devised, since the temperature of the source studied is apt to be so hot as to greatly injure any part of the body that comes near it, to say nothing about direct contact with it. Definition of Temperature.—The temperature scale is based upon two fixed points, the temperature of freezing water and the temperature of boiling water. This temperature interval, depending upon the scale

Jan 1, 1936

By H. E. Mussey

When the American Institute of Mining Engineers visited the Birmingham district in May, 1888, the four Ensley furnaces (Fig. 1) then completed were referred to as monumental.' Their dimensions are givcn in Table 1. Mr. Gordon stated, with considerable satisfaction, that on the preceding day one furnace had produced 165 tons. The blast was

Jan 1, 1925