Search Documents

By R. J. Mellen

In a chloridizing roasting and cyanida-tion plant treating a manganese-silver ore, certain experiments pointed out the way to an improvement in roasting conditions by a change in the degree of crushing. The following short article is simply a description of the various changes that were necessary throughout the plant and of the results obtained. There is nothing unusual in these changes but they are of some interest in that they constitute a good many of the alterations usually resorted to in increasing production. In the beginning, the changes were brought about by an experiment that was not successful, but which clearly pointed to means of improving the operation, and is an example of the fact that often experimental work may result in failure and still be of value in arriving at correct fundamentals. This experiment also shows how far a metallurgist can get out of line in his deductions, particularly in a field with which he is not thoroughly familiar. The ore at the plant of Compania Minera Kildun y Anexas is crushed through a 13-in. gyratory, a 3-ft. standard Symons cone crusher and a set of 16 by 42-in. rolls, the latter in closed circuit with two Tyler type 400 screens. The crushed ore is then conveyed to two fine-ore bins. These provide storage and feed for two 6 by 90-ft. kiln roasters, which discharge directly to coolers. The coolers in turn discharge to a 6 by 12-ft. ball mill, where the ore is ground for cyanidation. Laboratory and pilot-plant tests previous to the mill construction had indicated that minus ¼-in. crushing was satisfactory for roasting, although results did not vary greatly with some coarser or considerably finer crushing. The plant was designed for a capacity of 300 tons per day on this basis. After a few months operation, the initial operating problems were overcome and the anticipated milling rate was reached but the results being obtained were not really good. The plant seemingly did not have much excess capacity in any department but the roasting operation was the most critically limiting factor both as to tonnage and the results obtained. If this could be improved there seemed some possibility of improving the total tonnage rate to some extent. Segregation of the calcine into various screen sizes showed that the coarser sizes were not giving the expected recoveries. In all of the laboratory and pilot-plant testing, any limiting conditions as to the percentage of salt used, temperatures, feed rates, etc., had affected the fine material more than it had the coarse, and even in making laboratory tests at this time the mill conditions could not be exactly duplicated. Further laboratory testing indicated that a segregation of the rushed Ore into a coarse and fine product for roasting might result in some improvement in roast-

Jan 1, 1947

By R. J. Mellen

In a chloridizing roasting and cyanida-tion plant treating a manganese-silver ore, certain experiments pointed out the way to an improvement in roasting conditions by a change in the degree of crushing. The following short article is simply a description of the various changes that were necessary throughout the plant and of the results obtained. There is nothing unusual in these changes but they are of some interest in that they constitute a good many of the alterations usually resorted to in increasing production. In the beginning, the changes were brought about by an experiment that was not successful, but which clearly pointed to means of improving the operation, and is an example of the fact that often experimental work may result in failure and still be of value in arriving at correct fundamentals. This experiment also shows how far a metallurgist can get out of line in his deductions, particularly in a field with which he is not thoroughly familiar. The ore at the plant of Compania Minera Kildun y Anexas is crushed through a 13-in. gyratory, a 3-ft. standard Symons cone crusher and a set of 16 by 42-in. rolls, the latter in closed circuit with two Tyler type 400 screens. The crushed ore is then conveyed to two fine-ore bins. These provide storage and feed for two 6 by 90-ft. kiln roasters, which discharge directly to coolers. The coolers in turn discharge to a 6 by 12-ft. ball mill, where the ore is ground for cyanidation. Laboratory and pilot-plant tests previous to the mill construction had indicated that minus ¼-in. crushing was satisfactory for roasting, although results did not vary greatly with some coarser or considerably finer crushing. The plant was designed for a capacity of 300 tons per day on this basis. After a few months operation, the initial operating problems were overcome and the anticipated milling rate was reached but the results being obtained were not really good. The plant seemingly did not have much excess capacity in any department but the roasting operation was the most critically limiting factor both as to tonnage and the results obtained. If this could be improved there seemed some possibility of improving the total tonnage rate to some extent. Segregation of the calcine into various screen sizes showed that the coarser sizes were not giving the expected recoveries. In all of the laboratory and pilot-plant testing, any limiting conditions as to the percentage of salt used, temperatures, feed rates, etc., had affected the fine material more than it had the coarse, and even in making laboratory tests at this time the mill conditions could not be exactly duplicated. Further laboratory testing indicated that a segregation of the rushed Ore into a coarse and fine product for roasting might result in some improvement in roast-

Jan 1, 1947

The meeting of the Institute at St. Louis brought together many members of the Women's Auxiliary, and Mrs. Philip N. Moore, who was nominated as the Director for the St. Louis Section, took the occasion formally to inaugurate the organization in that district. A meeting was held at the Planters Hotel, anti after discussion as to, the aims and objects of the. Auxiliary, officers were nominated for the' Section; the meeting then adjourned for two days, to he resumed in Joplin.. Here a very successful meeting was held, at which the Vice-Chairman, Secretary, and Treasurer were elected. A great deal of interest was arouse under the able directorship of Mrs. Moore the St. Louis Section is likely to become a large and active organization. The president of the Women's Auxiliary, in opening the meetings, told the ladies present of the inauguration of-the-Society in February, 1917, and of the work which had been accomplished up to date. She told how the Society devotes itself to patriotic and humanitarian work along lines acceptable and interesting to the Mining Engineer, standing always alongside and behind the men of the profession. The Central Welfare Committee of the organization has three Sub-Committees: Foreign Relief, Emergency, and Americanization, and under one or other of those heads most of the work of the' Society has been done. Mr. Hoover was responsible for the inception of the Foreign Relief Committee, as its first work was the collection of funds for the supplementary meals for the Belgian Children. Under the energetic administration of Mrs. H. Knox, this sub-committee raised $12,100 in the period between the February meeting and the Declaration of war by the United States, when our government took over the entire duty of feeding starving Belgium. The organization of the Belgian Relief Committee, as it was styled, still remains, but the members are now asked to take up the question of relief in France. The President, Mrs. S. J. Jennings suggested at the St. Louis meetings that one way of working for the foreign relief alight be that all the members of the Auxiliary should, during the period of the war, forego all giving' and receiving of Christmas presents, except those they have been accustomed to give to the poor or in charity, and those they would give to the men in the services of the United States; that the money usually spent on the Christmas gifts should be put into a fund to be sent abroad for the fatherless children of France, as a gift from the families of the Institute. A good deal of discussion followed this proposal, as some of the ladies felt that children should have their Christmas gifts as usual. The Director of the Section emphasized the truth that the Christmas spirit was the .spirit of giving and sacrifice, and that no sacri-

Jan 1, 1918

By George Hallerman, R. J. Gray

In the customary method of studying age hardening, the process of aging is interrupted by cooling the specimen and measuring its room-temperature hardness. However, the aging process may be conveniently measured while it is occurring at an elevated temperature by a series of hardness measurements at suitable time intervals. The latter method gives data void of complications that might result from processes occurring during the quench, and the data may be more indicative of the alloy's properties at elevated temperatures. The elevated-temperature hardness tester1 used in the present study employed a dead-weight loading system with a synthetic sapphire Vickers-type in-denter mounted in a molybdenum holder. The tests were performed in a vacuum of l0 to 10 torr. Hardness impressions were made by applying a 2-kg load for 15 sec. Although the hardness impressions made in the tester at elevated temperatures were measured at room temperature, the correction for thermal contraction during cooling was insignificant and therefore neglected. The two methods of obtaining age-hardening data were compared using eighteen samples of Haynes alloy No. 25* which had been annealed for 2 hr at 2250°F (1232°C). The test surfaces of the 1 by 1 by 1/4-in. samples were ground and then polished on vibratory polishers2 prior to testing. Three groups of five samples were aged at 1400°, 1650°, and 1800°F (760°, 899", and 982°C) for 4, 16, 32, 64, and 100 hr and then water-quenched. Room-temperature hardness as a function of aging time for these samples is shown in the broken lines of Fig. 1. Only one sample for each of the three temperatures was necessary to determine the hardness of the alloy at the aging temperatures with the elevated hardness tester. The specimens were heated isothermally and hardness impressions were made after various time intervals up to 100 hr. The results of these determinations were represented by solid lines in Fig. 1. Comparison of the two sets of curves shows, as expected, the hardness values determined at the aging temperatures are lower than the room-temperature hardness of the quenched specimens and the hot-hardness values reflect a strong tempera-

Jan 1, 1964

[ ]

Jan 2, 1968

By Robert T. Hill

The successful completion, January 10,1901, by Capt. A. F. Lucas, of a well, near Beaumont, Texas, whereby an enormous flow, estimated at '75,000 barrels a day, was obtained, opened a new oil-field in the United States, kindled a frenzy of exploitation and speculation, revolutionized the fuel industry of a large region, and brought gain to thousands of people. Even to-day, it is impossible to cast up the present results or to prognosticate the future influence of this event. It has caused the revival of attention in other localities where oil had been suspected, and exploration for oil throughout the Texas region. It has attracted notice to the mineral resources of the Texas region, and created an interest in the geological conditions of that great State. This State, which has increased in population and wealth, as recorded by every succeeding census, with leaps and bounds such as are exhibited by no other part of the Union, now stands fifth in population and first in productive wealth per capita. Its fields, pastures, forests and mines teem with raw material. The whole economic evolution of the State has gravitated toward a focal point where these products were available for the coming of the kiln, the machine and the factory. The only drawback to the prosperity of the State was the lack of an economic fuel, inferior coal costing an average of $5.00 per ton at the time of the Beaumont discovery. This

Jan 1, 1903

By M. G. F. Söhnlein

IN THE metallurgical treatment of sulfide silver-tin ores mined at Oruro, Potosi, and Chocaya, the most important and difficult step is chloridizing-roasting. The ores are chiefly mined from veins in rhyolite, a detailed description of which can be found in most textbooks on ore deposits. The chief gangue minerals are Pyrite and quartz, and the silver content is derived from tetrahedrite, jamesonite, stibnite, and cylindrite. Most of the tin is present in the form of a rather impure cassiterite, which forms microcrystalline aggregates of varying richness with quartz and pyrite; occasionally, some tin is found as stannite, cylindrite, and other complex sulfantimonates. The silver content of the minerals that compose the ore is approximately as follows: Pyrite, 3 to 5 oz. per ton; jamesonite, 30 to 50 oz. per ton; stibnite, 30 to 150 oz. per ton; cylindrite, 200 to 300 oz. per-Jon; tetrahedrite, 500 to 3000 oz. per ton. Occasionally, some ruby silver ore is found, but it is very rare. In the mines of Oruro, which are the deepest in the sulfide zone, tetrahedrite has nearly disappeared, stibnite, jamesonite, and, in the deepest levels, cylindrite taking its place. At present, there are six mills treating this ore, two at Potosi, two at Chocaya, one at Poopo, and one at Machacamarca. The ore is crushed dry, given a chloridizing roast, leached with water and hyposulfite solution (or with brine) to extract gold, silver and copper, and concentrated for tin with or' without regrinding.

Jan 8, 1920

By D. M. Beeson, G. D. Ortloff

Water-propelled banks of carbon dioxide recovered both high- and low-viscosity crude oil substantially in excess of that recovered by water flood in linear flow model experiments. The increase in oil recovery is explained by oil swelling and viscosity reduction. Additional oil was recovered by solution gas drive at the end of the carbon dioxide floods when the model systems were depres-sured. This study was an investigation of the use of a water-driven carbon dioxide bank to recover crude oil. Techniques involving the injection of carbon dioxide have aroused con-siderable interest in recent years among methods considered for increasing oil recoveries. A number of investigators have studied the process in the laboratory1-' and in the field.7,5 Laboratory studies referenced indicate that carbon dioxide in conjunction with water flooding recovers more oil than does water flooding alone. These re- ports diverge widely, however, in stating magnitude of improvement. We believed that a water-driven carbon dioxide bank would increase recovery of crude oils by two mechanisms: viscosity reduction and oil swelling. Due to reduction in the oil viscosity caused by solution of carbon dioxide, displacement efficiency should be improved. In addition, the residual oil should be highly swollen by the carbon dioxide held in solution. Thus, the final residual oil saturation, in terms of stock-tank oil, would be lower than in the absence of carbon dioxide. To test this hypothesis, experi-

By R. A. Meussner, R. T. DeHoff, F. N. Rhines

ZINC diffuses through copper more rapidly than does tin. Accordingly, when a ternary diffusion couple is made, by bringing an 0 copper-zinc brass into contact with an a copper-tin bronze at fixed high temperature, it is to be expected that zinc will diffuse into the bronze faster than tin diffuses into the brass. Adjacent to the brass side of the couple the total alloy content (zinc plus tin) should diminish, therefore, while next to the bronze side the alloy content should increase. Since the path of compo- sition change must be continuous, in a single-phased alloy, it should follow a curved and, in general, an S-shaped course. The realization of this prediction is demonstrated in Fig. 1, where the composition paths of two ternary diffusion couples are plotted on the appropriate isotherm of the copper-tin-zinc phase diagram. The diffusion couples were both made from a binary copper-tin alloy analyzing 5.0 pct tin placed against binary copper-zinc alloys analyzing 18.9 and 29.3 pct Zn, respectively. These alloys were produced from electrolytic grades of copper and zinc and a pure grade of straits tin, melted under borax in clay-graphite crucibles and cast in a vertical iron mold. Cylindrical pieces 1 in. in diam and 1 % in. long were machined from the casting and were faced by metallographic polishing to good matching end surfaces. Pairs of the cylindrical pieces were held

Jan 1, 1959

By I. L. Greninger

THE property of the Andes Copper Mining Co. is in the central part of the Republic of Chile, Province of Atacama, 147 km. (91.5 miles) eastward by rail from the port of Chañaral. At this point the Andean system is made up of two principal ranges. The mine is on the westerly slope of the outer, or western, range, at a mean elevation of 3250 m. (10,500 ft.). A meter-gage railroad extends from the company's port at Barquito, near Chañaral, to the reduction plant at Potrerillos. This road has a total length of 151 km. (94.0 miles), of which 93 km. (57.79 miles) are owned by the Andes Copper Mining Co. The remainder of the road is owned by the state. The company operates its trains over the portion of the road owned by the state, under an agreement with the Chilean Government. The mine is connected with the reduction plant by a meter-gage railroad, 10 km. (6.214 miles) long, which extends from the coarse ore bins at the metallurgical plant to the underground storage bins at the mine. Tunnels make up 60 per cent. of the total length of this railroad. As is characteristic of the Andean region in Chile, the topography of the locality is extremely rough, and a number of points near the mine have elevations of from 15,000 to 16,000 feet.

Jan 1, 1928

By C. Richard Tinsley

SUMMARY A detailed analysis of nickel, copper, and cobalt recovery from manganese nodules shows simple rates of return of 9-15% in 1985. A sulfur dioxide roast process yields a slightly better return than an ammonia leach technique. Nodule tonnage predictions tend to be over-optimistic and more conservative forecasts show that market penetrations are only significant for cobalt and manganese. However, cobalt prices are unlikely to fall to the level of nickel. Between now and 1985, cobalt is expected to be in balanced to tight availability. INTRODUCTION Deep-ocean manganese nodules are one- to two-inch concretions which cover 2040% of large areas of the ocean bottom. Commercial targets far these black, potato-like nodules are located in the North Pacific at water depths of 5,000-6,000 m. in a belt roughly midway between Hawaii and Mexico. However, good grade nodules are not solely limited to this belt as areas southwest and northwest of Hawaii, as well as in the Indian Ocean, contain concentrations of acceptable grade manganese nodules. Some 90% of the nodules are found half-buried on the deep ocean bottom. A siliceous-ooze host soil combined with low sedimentation rates, certain ocean currents, and possible geo- thermal effects are favorable factors far nodule formation. The viewpoints and analyses in this paper are the author's own and should not be attributed in any way to Amoco Minerals Co.

Jan 1, 1976

By Richard W. Markley

The predominant methods for mining coal in the USA are room and pillar and longwall. Approximately 95 percent of the coal is mined by room and pillar and 5 percent by longwall. The U.S. Department of Energy (DOE) has an ongoing program to improve the rate, quality, and cost effectiveness of stabilizing the roof for both of these mining systems. In room and pillar mining, the installation of permanent roof support is often the task which paces the system operation, and it thus controls the level of production achieved during any mining shift. Two automatic roof bolt insertion equipment developments are discussed, as well as a flexible drill for operation in thinner seams. Progress will be reported on under- ground trials of a particular flexible drill which has been combined with a bolt inserter to form a compact, reliable module for retrofitting to continuous mining machines. In longwall mining, the use of hydraulic supports on the working face provides roof stability. The DOE has several trials ongoing with shield- type supports in difficult strata conditions which are described, as well as a co-funded project with the Bureau of Mines on a resin injection remedial method for consolidating a shear zone at one site. A project to improve the match of strata conditions to shield design is also described, which involves the use of a 1360 tonne vertical load mine roof simulator.

Jan 1, 1983

By Otto Rellensmann, Eugene P. Pfleider

For many years mine surveyors and exploration engineers have sought an accurate means of transferring meridian underground by using the gyro-compass. These efforts have generally failed, either because they were inaccurate or because the size and cost of the unit were prohibitive. During the past ten years, however, great strides have been made. Autonetics in California has developed a comparatively light-weight (100-lb) gyro-theodolite, and the Institute for Mine Surveying at Clausthal Mining Academy in Germany has developed an instrument that is accurate to within 20" to 30" of arc. Concurrently, Minneapolis-Honeywell has produced an astounding gyro, the size of a salt shaker, that weighs less than 0.5 lb and compares favorably in performance with the 50-lb gyros of conventional design. This unit, designed for missile guidance, should be adaptable for surveying small boreholes. Given the proper interest and approach from the engineering fraternity, excellent gyro- compasses could probably be available for accurate underground survey work at nominal cost within the next three years. Principles of the Gyro-Compass: The gyro- compass, used for 50 years as a navigational instrument in ships and aircraft, senses the turning axis of the earth and points out true polar north. It does this by employing the earth's rotation, the force of gravity, and the precession characteristics of a gyro. For further details the reader is referred to several excellent publications1-3 covering the principles and application of the gyroscope.

Jan 5, 1959

By Severn P. Brown

Search for ore continued at a feverish pace-as can be attested to by anyone who has tried to arrange for extensive diamond drilling. The stakes are high, and so is the cost as was indicated by Selco Exploration Ltd. when they announced discovery of base metal sulfides at Uchi Lake in northwestern Ontario. It was apparently their first commercial find after 15 years of exploration at a cost of more than $10 million. For the first time in many, many years the big exploration news has come from east of the Mississippi River. In January, the New Jersey Zinc Co., in an unusually worded press release, stated that they had made a major zinc discovery of 13-50 million tons of ore averaging 5-10% Zn. New Jersey's holdings are said to embrace 500 sq mi. The ore was discovered in eastern Tennessee in the upper part of the Knox dolomite of early Ordovician age. Reportedly the mineralization is at depths of 900 to 2000 ft. Currently about 20 diamond drills are working the area for New Jersey. At least nine other major companies are prospecting the region, which now includes parts of Kentucky. Five hundred thousand acres are said to be under lease. Greatest activity is clustered around Carthage, Tenn. In Missouri, the St. Joseph Lead Co. announced plans to develop a new mine in the Brushy Creek area of the "New Lead Belt." copper and zinc concentrates will be by-products.

Jan 1, 1970

By W. L. Chen

The Batac jig was first introduced in the US for fine coal cleaning in 1973 (Tackett, 1977; Hake, 1976). Since then, a total of six such jigs of various sizes have been installed in five US plants for a total capacity of 2346 t/h. The raw coal size ranges from 19 mm x 0 to 9.5 mm x 0-fraction sizes previously fed to heavy medium cyclones, Deister tables, or water only cyclones. Growing interest in the Batac jig as a replacement for the above equipment is due to the following reasons: • Unlike heavy medium cyclones, no magnetite is required. As a result, the operating cost of the plant is reduced. • The compactness of equipment is unique on a unit ton per hour basis as compared to other equipment. • Solid state electronic control of jig stroke length, frequency, and jig bed depth makes the equipment highly efficient. Installations of Batac jigs in the US as of June 1980 are shown in [Table 1]. Use of the Batac jig is even greater outside the US (Anonymous, 1980; Chen, 1980). Its use is not limited to fine coal but is applied to coarse coal as well, with 102 mm size in the feed (Zimmerman, 1975). In countries where consumption of magnetite associated with the heavy medium system of coal cleaning is considered a waste of iron ore resource, the Batac jig is regarded as the primary choice in the selection of cleaning equipment (Chen, 1980).

Jan 1, 1981

By John A. Hosking

The recent activity of numerous foreign mining companies in the once flourishing tin fields in Cornwall, England has resulted in renewed interest in the evaluation of hypothermal tin deposits. These deposits are mainly narrow tabular bodies and are usually steeply dipping. They exhibit thermal zoning the mineralization changing from lead/zinc through copper to tin with depth. The tin zone virtually never exceeds 1,000' in depth and the ore shoots within this zone tend to be erratic and localized. The grade which is presently considered to be economic is about 0.7% Sn. , this means a concentration of about l% cassiterite (the only economic mineral) which, being twice as heavy as the gange, represents only. 5% of the lode volumetrically. Within the lode, only one third may reach this economic grade and values within the shoots can range from 100% cassiterite to zero over a few inches. The enormity of the problem of evaluating such a deposit has not been fully appreciated by the companies involved whose experience has, for the main part, been in larger and more predictable ore bodies. This paper attempts to put these problems into perspective and out- lines the useful applicatations of statistical and computer techniques. It also stresses the need for enlightened interpretation of data by men familiar with the problem and that even in this day and age, educated, intuitive deduction should not yet be relegated to the limbo of alchemy and witchcraft.

Jan 1, 1969

By Stefan Boshkov, Malcolm T. Wane

THE validity and accuracy of velocity measurements underground have been questioned repeatedly by those in mine ventilation work. The general disagreement on the subject is well illustrated in an AIME publication.' Although the presence of errors is readily admitted, their magnitudes are not known and often are described by practical operators merely as "great," "small," or "of no importance." The belief that errors are of academic interest only prevails because of a justifiable claim that actual volumes of air circulated are well in excess of those required by law and safe mining practices. Poor understanding of the source and nature of errors inherent in velocity measurements, coupled with questionable determination of cross-sectional area, result in faulty techniques for the purpose of expediting ventilation surveys and render doubtful the calculated volume. Often consistency of readings is confused with accuracy. A succession of check readings showing a maximum deviation of 5 pct in the measured value of velocity usually signifies nothing more than diligent application of technique in a stable ventilating current. This article discusses the errors involved in air measurements underground. Where instrument errors are presented, the treatment is confined solely to the rotating-vane anemometer, recognized as a most useful ventilation measurement tool because of its simple design and easy operation. In the following pages a positive deviation is defined as one which has to be added to the registered air velocity to obtain the true air velocity.

Jan 1, 1956

By E. A. Holbrook

AT the meeting of the Committee on Engineering A Education of the Institute at the New York meeting last February, it was brought out that the number of men graduating in mining engineering from our colleges at the present time is not sufficient to meet the ordinary needs of the mineral industries. Following the meeting, Samuel S. Wyer, consulting engineer of the Fuel-Power Transportation Educational Foundation of Columbus, Ohio, prepared a pamphlet called "Mining Engineering's Appeal to High School Seniors." Under the auspices of this Foundation the pamphlet is being sent to every high school in the United States. The pamphlet does not in any way paint glowing word pictures of the profession; rather it is a statement of the importance of mining engineering in our present-day civilization, together with the requirements in young men who are looking forward to an engineering career.

Jan 1, 1930

Coal Transport Via Pipe Line Claimed Feasible Moving coal via pipe line is a project proposed by the U. S. Bureau of Mines. A pipe line 100 miles long capable of transporting 5000 tons of coal a day with water could be built for about $10 million. The cost of moving the coal 100 miles would be between $1.28 and $2.01 a ton.

Jan 9, 1951

By AIME AIME

MOST of us are far .from home, and yet our Japanese hosts- have made us feel very much at home. Here in the Orient we engineers are .learning a new meaning for the word "orientation"- hereafter that engineering term will be a synonym for gracious hospitality, and "to orient" will mean to turn a whole country over to the World Engineering Congress. Mere geographic distance is no longer able to separate nations, for the conquest of distance is one of the triumphs of 'modern engineering. We of the Americas are fortunate in the position of our continents: with their shores lapped by the waves of two oceans, we face' two great civilizations, the' Occidental and the Oriental, and thus we can share the intellectual resources of these two older cultures.

Jan 1, 1929