Search Documents

By Paul F. Kerr

The uranium-producing areas near Marysvale, Utah provide an unusual group of veins and replacement deposits associated with a Pliocene-Oligocene intrusive and extrusive igneous complex. Aside from several scattered occurrences in older volcanics, uranium-bearing veins occur in intrusive quartz monzonite or granite and in nearby rhyolite. The veins in general trend within a few degrees of N55-65°E, are more or less vertical, and are found along the western margins of a quartz monzonite intrusive. The replacement deposits are found in rhyolite intrusives and also in the lower portions of rhyolite flows close to places where veins forming solutions rising through quartz monzonite came into contact with the rhyolite. At least 14 veins have been mined since uranium mining operations began at Marysvale some 16 years ago, while ore has been extracted through about 10 miles of underground workings. The active mmmg area is approximately 3000 feet long and in the central portion 1500 feet wide. Ores have been found over a vertical spread of almost 2000 feet, between the highest occurrence on Jungfrau Hill ( ca. 7200 feet) and the deepest discovery of ore in a drill hole near the Prospector Mine (ca. 5200 feet). Under existing mining and marketing conditions, mining along the veins in the main area appears to have reached an economic limit at about 500-600 feet below the surface. However, orebodies in the rhyolite and in the upper portions of veins close to the rhyolite are subject to active mining. Isotopic dates indicate that the uraninitebearing veins and replacements are late Miocene or Pliocene (ca. 10-13 m.y.), the rhyolite is Miocene (avg. 17.5 m.y.), and the quartz monzonite and granite intrusives are late Oligocene (23.6 to 26.0 m.y.). The older Bullion Canyon Volcanic Series which encircles the area is Oligocene (28 to 31.1 m.y.). Two generations of alteration occur: ( 1) Earlier alunitic veins and replacement bodies are found in the Bullion Canyon Volcanic Series, none of which have produced uranium; (2) Later argillic alteration associated with the introduction of uranium is found along veins, replacing glassy rhyolite dikes and replacing phases of the rhyolite.

Jan 1, 1968

By H. O. HOPMAN

(Canal Zone Meeting, November, 1910.) I. INTRODUCTION. THE substance of this paper was prepared for the Seventh International Congress of Applied Chemistry, held in London, May, 1909, under the title, Some Developments in Blast-Roasting. In the absence of the author, a -short abstract of the paper was read, and the abstract only will appear in the proceedings of the congress. The present paper has been partly rewritten and considerably enlarged by information gained since the original was prepared ; also some illustrations have been added. Blast-roasting' is a generic term for the process of forcing air through finely-divided. metallic sulphide with the object of roasting and agglomerating in a single operation. At first the process was confined to a galena-concentrate ; lime, limestone, or gypsum was added, to serve both as a diluent to keep separate the particles of galena that they might be thoroughly oxidized, and as a flux that the partly-roasted ore might be agglomerated by the formation of some slag. Later it was extended to treat other metallic sulphides. The leading processes were the Huntington-Heberlein and the Savelsberg of Europe, and the Carmichael-Bradford of Australia. In the United States and Canada, the Huntington-Heberlein process has found application in some instances with galena-concentrates, for which it was originally intended; but this class of ore is not often treated alone, hence the process has had to be modified to suit conditions. The Savelsberg process has been transplanted to this country in about its original form. The Carmichael-Bradford is not used at present. The changes called for in the Huntington-Heberlein process to adapt it to the class of lead-bearing ores usually smelted have been the 1 A. S. Dwight, Engineering and Mining Journal, vol. lxxxv., No. 13, p. 649 (Mar. 28, 1908).

Jun 1, 1910

By J. E. Cannaday, R. J. Austin, R. K. Saxer

PREVIOUS investigators have determined activation energies and have postulated various controlling mechanisms for creep.'-' Recently Barrett et 01.I5 have suggested, as the result of their work with cadmium, that the apparent activation energies for creep (AHc) above 0.5 T, could be correlated by means of activation energies for self-diffusion (AHSD) and modulus of elasticity functions: AHC = AHSD - (5RT/E) dE/dT. The wide disparity of apparent activation energies previously obtained with nickel compared to those reported for other fcc metals and the desire to test the postulate of Barrett el al. prompted this study. The as-received 17.5-mil nickel wire used during this work assayed 99.87 pct pure, Table I. X-ray analysis indicated that the wire was in a stress-re- lieved state and metallographic examination revealed an equiaxed grain size of approximately 0.01 mm. Specimens degreased in acetone and cut to 1-1/2 in. lengths were tested in a cam-mechanized constant-stress creep machine. A vacuum of at least lo-5 mm Hg was maintained during all tests. Stresses were applied when thermal equilibrium was established. When a measurable (at least 0.5 pct) secondary creep was observed, the temperature was pulsed to a higher temperature. Pulsing time varied from 30 sec at 480°C to 2 min at 1300'C and above. Slopes of creep curves were determined after the initial acceleration in the strain rate had subsided and steady-state creep was achieved. To confirm the results obtained, additional tests were performed incorporating a temperature pulsing method suggested by sherby. In this method the load was removed during temperature pulsing and reapplied after thermal expansion had occurred. No appreciable differences in results were obtained. Tests were performed over a wide range of temperature (470" to 1310°C) and stresses (250 to 17,000 psi). The expression was used to calculate activation energies. In this expression T1 and T2 are the initial and final temperatures, and el and i2 are the creep rates at T, and T2. The variation of the apparent activation energies with the mean test temperature calculated by means of Eq. [I] are shown in Fig. 1. The mean test temperature (Tmean) was calculated from the relationship

Jan 1, 1967

By W. J. Moore, E. M. Swiggard, H. Shenker

Beryllium is the most soluble of the double-acceptor impurities in germanium; the solubility is at least 1 x 10 19 atoms cm3. Photoconductive, optical, and electrical measurements were made on a set of Ge:Be samples grown without other intentionally added imp~ivities. The excited-states spectrum of beryllium in germanium was determined both in zero field and in magnetic fields up to 30 kc. It was found that the absorption 0-f lines in the vicinity of the G line increased markedly with increasing magnetic field. The ioniza-tion energy of neutral beryllium in germanium was determined to be 24.3 * 0.1 mez: using the excited-states spectrum. An infrared detector using a Ge:Be element was found to have a normalized detectivity D* (50 p, 1000 cps, 1 cps) of 9 X ldO cm-~ps"~-w-'. The Ge:Be sambles exhibited low-field breakdown and inibzirity band conduction effects at low temperatures. WHILE the properties of most dopants in germanium have been thoroughly investigated, the properties of beryllium in germanium have had relatively little attention. Much of the work that has been done' has been concerned with the properties of singly ionized beryllium in germanium. The purpose of the present work was to determine the photoconductive and electrical properties of beryllium-doped germanium (Ge:~e) with a small concentration of other electrically active impurities. Ge:Be is of special interest since beryllium is the most soluble of the known double-acceptor impurities in germanium. MATERIALS PREPARATION A set of &:Be crystals with beryllium concentrations between 5 x 1013 and 1x 10'' cmm3 and without other intentionally added impurities was grown in a hydrogen atmosphere by the horizontal zone-refining techniques described by Swiggard and Shenker.2 The segregation coefficient of beryllium in germanium was found to be about 0.07 and its maximum solubility was found to be greater than 1 x 10'' atoms cm-3 which is in agreement with previous results.' Most of the crystals were found to have a small net concentration of shallow acceptors; for example, a crystal having a beryllium concentration of 1.1 X 1016 cm-3 was found to have a net concentration of shallow acceptors of less than 1.5 X 1013 cm-3. Ingots designed to have a beryllium concentration of 1 x 1017 cm-3 or less exhibited a loss of electrically active beryllium. That is, the beryllium concentration was lower than expected and the decrease of the beryllium concentration along the length of the ingot was much larger than expected. It is hypothesized that this effect is due to the oxidation of the beryllium by the residual oxygen in the system. This effect is similar to but not as severe as the effect observed with boron in germani~m.3, 4 OPTICAL ABSORPTION SPECTRUM The excited-states spectrum of neutral beryllium atoms in germanium was studied by measuring the infrared optical absorption spectrum. A typical spectrum is shown in Fig. 1; the labeling of the absorption lines follows that of Fisher and Fan.* The spacings between the observed lines and the D line are nearly equal to the corresponding spacings for the other ac -ceptors in germanium.5-7 By the use of the theoretical result67' that the neutral impurity ionization energy is 2.53 mev larger than the energy of the D line, the ionization energy of neutral beryllium in germanium was determined to be 24.3 * 0.1 mev at 4.2"K. This method yields a more precise value of the impurity ionization energy than the usual Hall effect method.' The absorption spectrum of Ge:Be was also measured as a function of magnetic field using a magnetic field parallel to the incident radiation and using unpolarized radiation. A typical spectrum taken at 30 kG is shown in Fig. 2. An unexpected observation is that the absorption of the lines in the vicinity of the G line (there is a strong possibility that some of these lines may be associated with lines other than the G line) increases with magnetic field. RESISTIVITY AND HALL DATA Measurements of Hall voltage vs temperature were made on several of the samples. The thermal activa-

Jan 1, 1968

I-Mine Ventilation A C. CALLEN, Chairman E A. HOLBROOK, Vice-chairman H I. SMITH, Secretary CLARENCE E. ABBOTT ALFRED W. HESSE FRANK H. PROBERT GRAHAM BRIGHT G R. JACKSON GEORGE S RICE THOMAS H. CLAGTETT JAMES F. MCCARTHY E. J RISTEDT OSCAR A GLAESER W. B. PLANK GERALD F. SBERMAN, Coal Mining M D COOPER, Chairman HOWARD N EAVENSON JOHN A GARCIA THOMAS D THOMAS CHARLES ENZIAN JAMES W PAUL C M YOUNG JOHN J. RUTLEDGE Physiological Studies R R. SAYERS, Chairman C. L. BERRIEN W. D. BRENNAN A. J. LANZA

Jan 1, 1923

By Ralph W. Marsden

The natural iron ores of the Lake Superior Region in the United States are being replaced by iron-ore concentrates produced from magnetite- or hematite-rich horizons in the Precambrian cherty iron formations. The production of natural ores will soon be less than one-half of the total ore shipped annually. The tonnage of natural ore produced will continue to decline until it is a minor percentage of the ore shipped. The natural ores include (1) soft ore, (2) hard ore, ( 3) conglomerate ore and ( 4) siliceous ore. The soft ores are the important ore type and are sometimes termed "Lake Superior type ore". These ores are in situ deposits of hematite and limonite formed by the leaching of silica and other gangue materials in the iron formations. The leaching is believed to have been done by downward moving surface waters. In deep ore deposits, generally over 1000 feet below the present surface, circulation and leaching action may have been assisted by hydrothermal activity. Hard ore deposits occur on the Vermilion and Marquette ranges where hematite or magnetite has replaced the silica (and possibly some silicates) in cherty iron formation. These ores commonly occur in structural situations favorable for the movement of hydrothermal waters. The ores are believed to be the result of hydrothermal action with iron, possibly from the iron formation, transported by hydrothermal waters to areas favorable for the replacement of silica by iron oxides. Certain stratigraphic horizons of the Lake Superior Precambrian cherty iron formations contain sufficient iron as magnetite or hematite, with a grain size and texture that will give adequate mineral liberation, to yield an ore-quality product after grinding and concentration. The magnetite-rich deposits are termed magnetite taconites. These ores occur on the Mesabi, Gogebic, and Marquette ranges. Magnetite taconite ores are unenriched cherty iron formation and are the result of the sedimentary deposition of the iron formation and the metamorphic history of the rock. The commercial quality hematite-rich iron formations in Michigan are termed jasper ores. The jasper ores are being mined on the Marquette and Menominee ranges. These ores are composed of specular or granular hematite associated with quartz and iron silicates. The jasper ores appear to be recrystallized iron formations in which iron, prior to recrystallization, occurred as hematite.

Jan 1, 1968

By J. Van Steveninck, A. C. Pols, R. Feenstra

In the course of time, an increasing number of investigations on jet cutting all kinds of material, such as rock,1,2,3 metal,4,5 and wood6 have been reported to serve various applications. A number of papers have been published on these subject, 7,8,9 some of which refer to jets purposely containing abrasives, termed 'jetted particle drilling'.7 Since such abrasives complicate fluid handling considerably and do not appear to be absolutely necessary for making holes, only conventional drilling fluids have been considered. A large part of our investigation has been performed with the aid of three laboratory-type drilling machines, which permit tests on both micro-bits (1 ½ in. ) and full-scale bits (6 ½ -9 5/8 in. ) . In view of the application of jets in deep holes, care has been taken to simulate hydrostatic pressures as they exist in the field on the hole bottom. These have been found to have a major effect on the bit-penetration rate for various drilling fluids.

Jan 6, 1974

By Fred C. Bond

Many grindability tests have been made in the Allis-Chalmers laboratory since the tabulated results were last published.' The lists of standard ball-mill and standard rod-mill grindability tests are brought up to date in this paper, and considerable new material is added. This includes a tabulation of open-circuit grinding tests, with impact and compression-crushing tests. The standard ball-mill grindability tests (Table I) were made in a standard laboratory ball mill, 12 by 12 in. inside, running at 70 rpm, with a charge of 285 iron balls ranging from 1½ to 3/4 in. in diameter and weighing 20,125 grams. Seven hundred cubic centimeters of minus 6-mesh stage-crushed dry feed was used, and the circulating load was maintained constant at 250 pct by adjusting the number of mill revolutions for each grinding period. Tests were made at all mesh sizes from 28 to 200, and the grindability is the number of net grams of screen undersize produced per revolution. The table includes 479 tests. It has been calculated that the ball mill does 52.3 joules of useful work on the ore per revolution2 with 93 joules input to the mill. The standard rod-mill grindability tests (Table 2) were made in a laboratory tilting rod mill, 12 in. in diameter by 24 in. long inside, with a wave-type lining, running at 46 rpm. The grinding charge consisted of six I1/4-in. diameter and two 13/4-in. diameter steel rods, all 21 in. long and weighing 33,380 grams. The mill was rotated level for eight revolutions, then tilted up 5' for one revolution, down 5° for one revolution, and returned to level for eight revolutions. It was discharged by tilting downward at 45° for 30 revolutions. Feed consisted of 1250 cc of minus in. stone and the circulating load was maintained constant at 100 pct by adjusting the number of mill revolutions for each grinding period. Tests were made at all mesh sizes from 3 to 65, and the rod-mill grindability is the number of net grams of screen undersize produced per revolution. The table includes 105 tests. The impact and compression-crushing tests (Table 3) are given in a table that is an extension of a previous publication8 in which the method of testing was described in detail. Two equal hammers weighing about 30 lb each were arranged to strike simultaneous blows on opposite sides of the test specimen. Broken pieces of rock passing a 3-in. square and retained on a 2-in. square were set up with the smallest dimension between the hammers, and this distance was measured. The height of the hammers was increased slightly before each blow until the specimen broke, and the foot-pounds per inch of thickness was calculated. Ten pieces

Jan 1, 1949

By Samuel Taylor

IF I LIVE another fourteen months and am still con-nected with the coal industry, I shall then have com-pleted a half century with it. Since May, 1874, when .I first entered the bituminous workings as a miner, I think I have held almost every position connected with a mine except possibly that of mule driver, for which I was unfitted by reason of my religious upbringing. We are all agreed, at least I have not heard it contra-dicted, that there is serious over-production in the bituminous industry. This has come about in various ways and is easily explained. During the Fuel Admin-istration, I recall making an estimate of the possible output of the bituminous mines of the country provided they were given a full force of men and a full-car supply; my estimate was a little over a billion tons a year. A few months ago, the late Francis H. Peabody, of Chicago, made a practically identical estimate. If, however, both of these conditions should happen con-currently, there would very soon be no market for the coal, and many of the mines would close down. Even today, if 10 per cent. more cars were furnished, to the bituminous mines, market prices would drop very seriously.

Jan 4, 1923

By Richard Hamburger

Calculating machines permit the use of the more rapid cotangent and semigraphic solutions of plane triangulation. The results of these methods are as accurate as those of other methods. Simple adjustment of the net, and ease of calculation encourage more complete field work. Errors in field work or in computation are easily localized.

Jan 1, 1950

By W. Joseph Schlitt, William D. Southard, Bruce P. Ream, Lawrence J. Haug

The operation of Kennecott's Bingham Canyon copper precipitation plant, one of the world's largest, is described. This description includes a brief historical review of precipitation at Bingham and the general layout and operation of the present cone cementation facility. Current practices are based on results of studies undertaken to define improvements needed in each unit operation. These improvements were required to meet changing plant conditions and were implemented primarily within the constraints of the existing facilities. Specific unit operations included were the cone precipitators, the cone discharge thickener, the cone effluent settling basins, and the plate and frame filter presses. As a result of these improvements, loss of precipitated copper decreased and the degree of precipitation increased, raising copper recovery by 9 t/d. At the same time, iron consumption was reduced by 22.5 t/d. Problems in drying the cement copper were also overcome so that a product containing 12 - 15% moisture could be consistently delivered for smelting.

Jan 6, 1979

By G. W. Imholz

A number of interesting wells were drilled in north central Texas during 1940. The Shell Oil Company's Smith well in scc. 143, block I, H. and T. C. survey, Stonewall County, was completed for an initial production of 581 bbl. per day from the Mississippian limestone, with a total depth of 6065 ft. The same company's Patterson well, sec. 393, block D. H. and T. C. survey, Stonewall County, tested the Ellenburger limestone and was abandoned as a dry hole with a total depth of 6760 feet. In Nolan County the Tex-Harvey Oil Co. drilled a well in sec. 43, near the Tipton well, which was completed as a small producer in the Strawn section. The Tex-Harvey well tested this producing horizon but was abandoned as a dry hole with a total depth of 5210 feet. The Montour-Haggart well, sec. 184, block 2, H. and T. C. survey, Fisher County, tested the Strawn and was abandoned with a total depth of 5664 feet. The Georgian Oil Company's Blach, sec. 309, T. R. and L.. Shackelford County, encountered the top of the Ellenburger limestone at 4725 ft. After being plugged back to 3915 It. from a total depth of 4825 ft., the well tested 10 bbl, of oil per day and 300 bbl. of water. The W. I. Sothern No. 2 Carlisle well in sec. 293 was deepened to the Cambrian. The top of the Ellenburger was encountered at 6540 fcet. A wildcat well in Fisher County, the E. A. Stephenson-Maberry, apparently opened a new pool when the well encountered sand from 3298 lo 3302 ft. and was completed for 50 bbl. per day in the Cook sand horizon. In Jones County, the King Oil Company's Olsen well, sec. 158, B. B. B. and C. survey, extended the Avoca-Olander pool. The well was completed for 263 bbl. in 8 1/2 hr. from the Palo Pinto limestone, from 3298 to 3302 ft. Ungren-Frazier extended the Akard pool with No. I Akard, in the D. 'T. Bruce survey. The well was completed for 83 bbl. per day from the Cook sand, encountered from 2109 to 2126 feet.

Jan 1, 1941

By G. W. Imholz

A number of interesting wells were drilled in north central Texas during 1940. The Shell Oil Company's Smith well in scc. 143, block I, H. and T. C. survey, Stonewall County, was completed for an initial production of 581 bbl. per day from the Mississippian limestone, with a total depth of 6065 ft. The same company's Patterson well, sec. 393, block D. H. and T. C. survey, Stonewall County, tested the Ellenburger limestone and was abandoned as a dry hole with a total depth of 6760 feet. In Nolan County the Tex-Harvey Oil Co. drilled a well in sec. 43, near the Tipton well, which was completed as a small producer in the Strawn section. The Tex-Harvey well tested this producing horizon but was abandoned as a dry hole with a total depth of 5210 feet. The Montour-Haggart well, sec. 184, block 2, H. and T. C. survey, Fisher County, tested the Strawn and was abandoned with a total depth of 5664 feet. The Georgian Oil Company's Blach, sec. 309, T. R. and L.. Shackelford County, encountered the top of the Ellenburger limestone at 4725 ft. After being plugged back to 3915 It. from a total depth of 4825 ft., the well tested 10 bbl, of oil per day and 300 bbl. of water. The W. I. Sothern No. 2 Carlisle well in sec. 293 was deepened to the Cambrian. The top of the Ellenburger was encountered at 6540 fcet. A wildcat well in Fisher County, the E. A. Stephenson-Maberry, apparently opened a new pool when the well encountered sand from 3298 lo 3302 ft. and was completed for 50 bbl. per day in the Cook sand horizon. In Jones County, the King Oil Company's Olsen well, sec. 158, B. B. B. and C. survey, extended the Avoca-Olander pool. The well was completed for 263 bbl. in 8 1/2 hr. from the Palo Pinto limestone, from 3298 to 3302 ft. Ungren-Frazier extended the Akard pool with No. I Akard, in the D. 'T. Bruce survey. The well was completed for 83 bbl. per day from the Cook sand, encountered from 2109 to 2126 feet.

Jan 1, 1941

By J. D. Doherty

That America's great coal deposits eventually will be our principal source of liquid as well as solid fuels is generally accepted. Moreover, the day when synthetic oil from coal will begin to supplement our petroleum supplies does not appear to be far off. The American petroleum industry has not spared effort or expenditure in its attempt to keep pace with the demand for oil, and recent production has exceeded expectations. However, the rapidly rising demand for liquid fuels plus the increasing difficulty of finding and developing the new oil needed even to maintain present production rates make it highly unlikely that oil from domestic wells can fully meet future oil requirements. Therefore, it appears that one or more of the following courses must be followed: 1. Curtail oil consumption. 2. Increase imports. 3. Develop new sources such as synthetic liquid fuels.

Jan 1, 1949

By Kendall E. Born

Production of crude oil in Tennessee during 1940 was slightly more than 15,000 bbl., a decrease from 1939 of about 36,000 bbl. This sharp decline has been caused largely by curtailed activities in the shallow pools in Clay County, where approximately 3000 bbl. was marketed off the lease during the year as against more than 37,000 bbl. in 1939. The flashy production found in 1938 in the Celina area has been short-lived and the area is essentially abandoned. Failure to find steady production has been the major factor retarding developments in the northeastern Highland Rim area. The Mississippi lime production in Scott and Morgan Counties continued to show a steady decline. The Tennessee production by counties is shown in Table I. Table i.—Oil Production in Tennessee it1 1940 Production. Bbl. Number of County Wells Pumped 1939 1940 Scott............ 4 4,332 3.596 Morgan.......... I: 6,479 5,751 Fentress.......... 3 I,2XX 1,5xz Pickett........... 1 1.2XX Clay............. 8 37.200 3,XXX Developments There were 32 wells spudded in during 1940, four of which were drilling or only temporarily suspended on Dec. 31, 1940. Twenty-eight wells were completed during the year, four of which were commercial producers. The total footage drilled was 3I,214 ft. The more important wildcats are listed in Table 2; the distribution of 1940 oil and gas tests according to physiographic divisions is given in Table 3. Cumberland Platenu.—Thcre was one completion in the coal area of the state, a test that attempted to extend the Mississippi lime production in the Coon Hollow pool to the southeast in Morgan County. This test encountered only slight shows of oil in the producing horizons of the near-by Coon Hollow and Boone Camp pools. Some surface work was carried on by private interests during the year in Scott and Morgan Counties and two wells were spudded in early in 1941 The revival of interest in the Kentucky portion of the plateau will probably result in increased activity in this part of Tennessee during 1941. Several sizable blocks of acreage, some by major oil companies, are held in Scott, Morgan, and Cumberland Counties. Middle Tennessee.—The northeastern Highland Rim continued to be the most active area in the state with 20 completions, although this figure is about one third of the number drilled in 1939. Four oil wells, none with initial productions of more than I00 bbl., were completed in Clay, Fentress, and Pickett Counties. The producing horizons discovered in Pickett and Fentress Counties were in the "Sunny-brookJ' pays of Trenton age. The Clay County producer was an old test drilled deeper in which oil was found at 671 ft. in the upper part of the Stones River group of limestones, a common pay in this area. All four wells were drilled in or close to old shallow production. Deeper testing into the Knox dolomite group in this area was not particularly encouraging, although one well in Fentress County encountered some saturation at 1860 to 1869 ft. in the upper

Jan 1, 1941

By Kendall E. Born

Production of crude oil in Tennessee during 1940 was slightly more than 15,000 bbl., a decrease from 1939 of about 36,000 bbl. This sharp decline has been caused largely by curtailed activities in the shallow pools in Clay County, where approximately 3000 bbl. was marketed off the lease during the year as against more than 37,000 bbl. in 1939. The flashy production found in 1938 in the Celina area has been short-lived and the area is essentially abandoned. Failure to find steady production has been the major factor retarding developments in the northeastern Highland Rim area. The Mississippi lime production in Scott and Morgan Counties continued to show a steady decline. The Tennessee production by counties is shown in Table I. Table i.—Oil Production in Tennessee it1 1940 Production. Bbl. Number of County Wells Pumped 1939 1940 Scott............ 4 4,332 3.596 Morgan.......... I: 6,479 5,751 Fentress.......... 3 I,2XX 1,5xz Pickett........... 1 1.2XX Clay............. 8 37.200 3,XXX Developments There were 32 wells spudded in during 1940, four of which were drilling or only temporarily suspended on Dec. 31, 1940. Twenty-eight wells were completed during the year, four of which were commercial producers. The total footage drilled was 3I,214 ft. The more important wildcats are listed in Table 2; the distribution of 1940 oil and gas tests according to physiographic divisions is given in Table 3. Cumberland Platenu.—Thcre was one completion in the coal area of the state, a test that attempted to extend the Mississippi lime production in the Coon Hollow pool to the southeast in Morgan County. This test encountered only slight shows of oil in the producing horizons of the near-by Coon Hollow and Boone Camp pools. Some surface work was carried on by private interests during the year in Scott and Morgan Counties and two wells were spudded in early in 1941 The revival of interest in the Kentucky portion of the plateau will probably result in increased activity in this part of Tennessee during 1941. Several sizable blocks of acreage, some by major oil companies, are held in Scott, Morgan, and Cumberland Counties. Middle Tennessee.—The northeastern Highland Rim continued to be the most active area in the state with 20 completions, although this figure is about one third of the number drilled in 1939. Four oil wells, none with initial productions of more than I00 bbl., were completed in Clay, Fentress, and Pickett Counties. The producing horizons discovered in Pickett and Fentress Counties were in the "Sunny-brookJ' pays of Trenton age. The Clay County producer was an old test drilled deeper in which oil was found at 671 ft. in the upper part of the Stones River group of limestones, a common pay in this area. All four wells were drilled in or close to old shallow production. Deeper testing into the Knox dolomite group in this area was not particularly encouraging, although one well in Fentress County encountered some saturation at 1860 to 1869 ft. in the upper

Jan 1, 1941

By E. A. Nesbitt

THE important permanent-magnet alloys 15 years ago contained carbon and depended upon it for their permanent- magnet properties. In recent years great, advances have been made in a number of new alloys substantially free of carbon. These include Remalloy,l an alloy of iron, cobalt, and molybdenum, the various iron- nickel-aluminum alloys of the Mishima2 type, and the more recent Alnico V3 in which the best properties are developed by heat-treating in a magnetic field. The Mishima and the Alnico types of alloys are very brittle and after casting must be ground to size. This article describes a permanent-magnet material4 that can be machined as cast, and when handled with some care can be .rolled to thin sheet and drawn to fine wire. Optimum magnetic properties are developed by a simple heat- treatment, and at this time the ductility A of the alloy disappears. If the cast alloy is heat-treated without cold-working the magnetic energy product is about 1.0 X 106. This material is called Vicalloy I (pronounced vicalloy, V for vanadium, I for iron, and C for cobalt). When the alloy is first hot-worked and then considerably reduced in area by cold-swaging, drawing or grooved rolling, it is found that after heat-treatment the magnetic energy product measured in the direction of previous extension can be increased to 2.0 to 3.5 X l06. These higher values have been obtained only after reductions in area of 75 to 95 per cent, and since the material hardens considerably during working, the reduction ordinarily can be accomplished only in fine wires, although larger sizes can be reduced by the use of powerful machinery. When the material has been cold- worked in such a manner as to improve its energy product substantially, it is called Vicalloy II. Commercial use of Vicalloy has been made in the recording of speech. Tape 0.002 by 0.050 in. has been found superior in quality to all others tried, and is now used in the Western Electric Mirrorphone In a variety of forms Vicalloy I or II is useful in many laboratory instruments, and in experiments in which the sizes and shapes required cannot be obtained with the other more brittle permanent-magnet materials. In 1936, during a study of other age- hardening magnetic systems, it occurred to the author that some of the iron-cobalt-vanadium alloys might be suitable for permanent magnets. The proportions of iron, cobalt, and vanadium were varied and a range of alloys of particular interest was found, as shown by the indicated area in Fig. I. The limits of this range of com- position are 30 to 52 per cent iron, 36 to 62 per cent cobalt, and 4 to 16 per cent vanadium. The compositions indicated by points outside this area were also tested. PREPARATION AND PROPERTIES OF VICALLY I The alloys were usually cast in graphite molds into bars ¾ in. in diameter and

Jan 1, 1946

By R. M. Howe, J. Spotts McDowell

Preparation and Use.—Magnesite is an important refractory in open-hearth, heating, and electric furnaces for steel-making and in many of those employed in the metallurgy of copper and lead. It is sold in the form of brick, finely ground "furnace magnesite" for bricklaying, and dead-burned grains for making and repairing furnace bottoms. The latter are a mixture of granules varying in size from pieces of about 5/8 in. (1.6 cm.) diameter to very fine but sandy particles. Dead-burned magnesite results from calcining the crude or lightly burned mineral at a temperaturc that will not merely drive off practically all the CO2, but will also cause sintering of the particles. During this process the pieces shrink considerably and become hard, dense, and inert to atmospheric moisture and CO2; under-burned material, on the other hand, will hydrate on exposure to the air. A small percentage of ferric oxide seems to be necessary for the production of a satisfactory sinter; from 4.5 to 8 per cent. in the dead-burned grains is considered the most desirable amount. Dolomite has been little used for brickmaking in the United States, but it is prepared for use in the granular condition calcined or "double-burned" and is the principal ingredient of several materials offered for sale under various trade names for refractory purposes. Dolomitic refractories are almost wholly confined to the open-hearth and electric furnaces, where they are used for fettling and as substitutes for magnesite. Much more magnesite and dolomite are used for basic open-hearth steel-making than for all other refractory purposes. The hearth of the furnace is usually built up of magnesite brick and dead-burned grain magnesite so laid that the brick base is protected by a working bottom of the granular material. The latter is sintered into place in layers 1/2 to 1 in: (1.25 to 2.5 cm.) thick to a total depth of 12 to 18 in. (30 to 45 cm.) at the center of the furnace. After each heat, burned dolomite is thrown against the banks as high as it will stick, and all holes in the bottom are Glled. At most plants such holes, at the end of each week, are also carefully filled with dead-burned grain magnesite. For temporary

Jan 1, 1920

By H. Rush Spedden, A. M. Gaudin

IN the belief that a critical study of its operating problems might be a sound investment, the Cuban American Manganese Corporation initiated an ore-treatment research in cooperation with the Massachusetts Institute of Technology. One of the early objectives of this research naturally became the relationship of the microscopy of the Cuban ores of the Corporation to their flotation treatment. The operations in Cuba have already been described by F. S. Norcross, Jr.7 and the laboratory study of manganese oxide flotation goes back a number of years .4 Broadly speaking, the difficulties encountered in the flotation of manganese ores are that the consumption of reagents is extremely high, the concentrate contains more silica than is desirable and the tailing losses are relatively high. An appreciable betterment on any of these scores would achieve a definite betterment in costs, quantity of minable ores, and quality of product. The microscope study discussed in this paper was made on samples from the Quinto mine, from the Ponupo mine, and from mill products at various stages of passage of the ore through the mill. The writers have had access to Company records and in particular to the petro¬graphic studies made on thin sections of ore by the late Professors R. J. Colony and Philip Krieger, of Columbia University. They acknowledge their debt to both of these men for the help derived from the reports. Manganese oxides are black, friable, smudging. It is, therefore, very difficult to judge operations by inspection. The mineralogy of manganese compounds seems to be confused, and the authors believe that many more minerals have been described than actually exist. Much of this difficulty is due to the prevalence of the structural conditions that will be discussed further in this paper; namely, the porosity and the friability of the ores, and the extremely intimate association of minute manganiferous mineral crystals with impurities of various sorts. By all odds the most important manganese mineral in Cuba is the one that in this paper is called "psilomelane." The name "psilomelane" has been used in so many different ways that the choice of it for this ore may not be approved by all. However, it seems to be the best under the circumstances. This mineral accounts for about 97 per cent of the manganese in the ores of the Quinto and Ponupo mines and in the mill feed. The remaining odd 3 per cent consists mostly of pyrolusite together with minor amounts of other manganese oxide minerals. DESCRIPTION OF PSILOMELANE Aggregate Structure In grains or lumps, psilomelane has a characteristic fibrous appearance and seems

Jan 1, 1942

By J. R. Cain

ROLE OF GASES IN FERROUS -METALLURGICAL PROCESSES IN every process for making steel there are one or more stages where the metal is exposed to gas of one kind or another. Thus, in the open-hearth furnace, the carbon dioxide and water vapor in the products of combustion are oxidizing toward the ferrous and manganous oxides in the slag, tending to convert these to higher oxides; the higher oxides then oxidize the steel, so that indirectly the products of combustion are oxidizing toward the steel. In the Bessemer process, there is direct contact of air and steel; also, the water vapor in the air blown into the converter is continually decomposed by the molten steel, yielding hydrogen and ferrous oxide, both of which are in part taken up by the metal. In the electric-furnace processes, there is always more or less air in contact with the slag covering the metal, and this air and the gaseous reaction products from it are dissolved in the slag to some extent and thus transmitted in part to the steel. In the crucible processes, there is always entrapped air in the charges and the crucibles are more or less permeable to the gaseous products of combustion from the furnace. In all the processes of manufacture, the molten metal is exposed to air while tapping into ladles and ingot molds and has an opportunity to saturate itself with air or with gaseous or solid products generated by chemical reactions between air and steel. Sieverts1 has shown that molten metals require but a few seconds to saturate themselves with a surrounding gas. No one familiar with the operations at a steel plant needs to be reminded of the important role that gases play at all stages. The familiar "boil" of open-hearth furnaces, due to evolution of carbon monoxide when iron ore is added to the molten steel; the spectacular operation of the Bessemer converter brought about entirely by a gaseous reagent; the almost magic effect of small quantities of silicon manganese or

Jan 8, 1919