Search Documents

By Joseph W. Leonard

The purpose of this paper is to review and discuss some of the less evident and sometimes neglected opportunities for progressive developments in coal research. While a great deal of both promotional and technical information flows from some areas of coal research, output deficiencies in other areas of activity have reached a magnitude where important developments have been, and will increasingly be, unfavorably affected. These areas mainly involve coal mining and preparation. Some recommendations for the intensification of effort in these areas follow: Coal Mining While a huge tonnage of in-the-ground coal is assured, the location and distribution of these tonnages are becoming less favorable. The easy-to-mine coal which is located in or near population centers has been, or is being, mined. The vigor with which the less accessible reserves are recovered by the mining industry depends largely on the condition of the coal market at the time of mining. Hence, during a buyer's market, the commercially oriented mining industry is compelled to mine the easier and less costly reserves. Conversely, during a seller's market, the need to rapidly expand production results in more difficult mining and higher cost coal as few obstacles are encountered in finding markets. Hence, a seller's market tends to enhance the recovery of reserves while a buyer's market does not. One reason for today's fuel supply problems is that the Nation has recently emerged from a long-term coal buyer's market which lasted from about 1950 to 1968. During that period, national policy caused severe production cutbacks which regretably drove the industry to mining only the more accessible and better quality reserves. Often in order to remain in business, many hundreds of millions of tons of more difficult to mine reserves were abandoned and lost behind caved areas. Many of these reserves are close to population areas and would not have been lost in a more stable economic climate. It is difficult to fully account for all the impacts that were caused by the great buyer's market of the 1950s and 1960s. Besides the obvious loss of reserves that were once considered national wealth, the mining of better reserves tended to produce a generation of technically optimistic mining people. Mining people frequently became accustomed to looking at nothing less than outstanding mining conditions as a result of the declining market. Many are now and have long since received a re-education in the other half of mining. Going from many years of mining accessible, select and easy-to-win reserves, to the crash-driving of development entries in reserves that were considered unworthy of mining during 50s and 60s, frequently results in a much higher rate of encounter with in-seam and out-of-seam rock as well as with coal-deficient areas or "washouts." Intensive entry driving activity and compulsory non-selective mining in sometimes lean reserves were brought on by the need to rapidly open up new supplies of coal. Working under these requirements presents a continuing reminder that much more needs to be known about the relatively esoteric art of planning the best direction for driving entries in order to insure that a more consistent and greater supply of coal is available during early mine development. All of the preceding discussion tends to point to a need for a better estimate of those reserves of coal that are likely to be mined in the future. Such estimates should not be limited to the compilation of the amount of coal in the ground; but, where possible, should also include information concerning the capability for producing this coal. After all, a coal seam of ample thickness may have a degree of thickness variability, undulation, bad roof or floor, so as to make what would otherwise appear to be an attractive mining condition untenable. Underlying the problem involving the feasibility of producing known reserves is the need to develop better methods for the characterization of coal seams and associated lithotypes, based on drill core data, once at area is selected for mining. Reserves and their characterization involve aspects of exploration technology that are frequently considered mature. The resulting technological deficiencies may be the main reason why coal exploration frequently does not end with core drilling of a property, as it should, but extends into the mining operation during the driving of development entries. When exploration is extended to the driving of development entries, the near absence of integrated decision-making theory involving mining, geology, mathematics, and economics becomes, once again, all too painfully apparent and frequently results in very costly rationalizations. Hence, by the formal initiation of a concentrated program to combine the cyclical effects of economics with geology and mining, more relevant estimates of reserve distribution, tonnages, and production capability should be forthcoming. Moreover, a similar formal effort is needed to develop a combination of the most advanced concepts of mathematics, geology, and mining to better "see" coal seams as a means to favorably implement many long-range decisions involving mine safety and productivity. Much more applied research needs to be done on coal mining systems for mining in thin seams and/or under bad roof. Current difficulties in both of these areas at recently opened coal mines should provide a sobering glimpse into the future. Full-scale applied research, sponsored by appropriate federal agencies, is urgently needed on a scheme involving a new combination of established mining and preparation elements. The scheme may include: (1) a continuous mining machine remotely operated by a miner stationed at some distance behind the machine using a cord attached control box; (2) hydraulic transport of coal through pipes from the mining machine to a coarse refuse removal grid, crusher, and then on to portable concentrating equipment; (3) the hydraulic transport of clean coal out of the mine in pipes to the surface for thermal dewatering, if neces-

Jan 1, 1974

The Library of the above-named Societies is open from 9 A.M. to 10 P.M., except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and the publications of - scientific and technical societies members of the Institute, with few exceptions, are forced to spend a portion of their time 'in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render - valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish genera1 information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 10, 1916

By J. H. Nead

Discussion of the paper of J. H. NEAD, presented at the New York meeting, February, 1916, and printed in Bulletin No. 108, December, 1915, pp. 2341 to 2357. E. D. CAMPBELL, Ann Arbor, Mich.-Any one at all familar with research work can at once see that Mr. Nead has condensed into his tables and curves the results of a carefully planned set of experiments which must have involved a great amount of work on his part. He deserves much credit for the way in which he has carried out these experiments, for it is to the results of such systematic experimentation that we must look for further knowledge of the underlying causes which determine the physical properties of steel. It will probably be many years before we have sufficient knowledge of all the factors of the problem of the constitution of steel, but every set of carefully carried out experiments such as Mr. Nead has made adds something to our knowledge and brings us a little nearer to the final solution of the problem.

Jan 5, 1916

By S. E. Piper, E. M. Buchalter, R. P. King, E. T. Woodburn

The problems involved in an optimum decision making model for flotation circuit are, first of all, to characterize the feed material in terms of parameters which can quantitatively describe the network flotation action in terms of a feasible set of control actions. Once the characterization has been postulated, it is then necessary to devise tests relating to parameter sensitivity, in order that credibility of the model predictions can be assessed. Once a credible model is available, the optimum control set is determined by a hill climbing technique. Details will be reported as to the credibility of model predictions using the stochastic flotation model on a network and further, computational problems associated with hill climbing for a complex objective function are reviewed. Discussion is presented on use of the Rosenbrock technique with constraints and use of a modified objective function with constrained derivatives when employing Fletcher and Powell technique.

Jan 1, 1969

By John V. Beall

Many Americans will judge the energy crisis by the picture shrink on their TV screen. And they are right to make this assessment considering the large areas of the country with marginal generating capacity, (See Fig, 1). The Federal Power Commission (FPC) recommends 20-25% reserve generating capacity above peak summer loads and 15-20% as minimal. The New York metropolitan area is the most concentrated power service area in the United States, and a spot check with Consolidated Edison, serving this area, revealed that on Friday, August 18, the company was operating at 5% reserve.

Jan 10, 1972

The Library of the above-named Societies is open from 9 A.M. to 10 P.M., except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is, desired and not include collateral natter which may not be of interest. The time spent in-searching for such collateral matter will be saved, and the information will be sent more, promptly and-in more usable shape.

Jan 2, 1917

By Louis Stott

IT is well known that the oxide of beryllium was identified as a new "earth" in 17971 and the metal first isolated in 18272. The history of the many difficulties encountered by early investigators, the laboratory achievements of Lebeau3, Fichter4 and Oesterheld5, and the eventual development of methods for commercial production are well covered in the literature, particularly in the authoritative published work of Siemens and Halske6 reviewing their comprehensive investigation of the element. Accordingly it has seemed desirable to restrict this paper to the properties and uses of beryllium and its alloys.

Jan 1, 1936

By M. P. Board, M. J. Reus

Instrumentation was installed during construction of the Silver Shaft in northern Idaho to evaluate lining behavior and rock deformation. Rock mass displacements were monitored with multiple-position borehole extensometers. Liner stress and strain were measured with concrete pressure cells and embedment strain gages. Rock displacement data from the 5,955-ft level indicate rock mass anisotropy. Liner stress and strain data reflect high in situ stresses and nearby station and raise construction. Continued monitoring and preliminary analysis indicate that concrete-lined, circular shafts are stable for high, unequal stress fields and anisotropy in deep level mines.

Jan 1, 1984

By E. F. Burch, R. W. Schoenberger

This paper deals with an investigation of the use of steam filtration for filter cake dewatering and shows that it may be applied on a practical scale. The advent of larger quantities of minus 1/4 in. coal in the raw feed to the preparation plant and the necessity of recovering this material has made the problem of meeting product moisture specifications more difficult. For a number of years thermal dryers have been used advantageously as a means of reducing fine coal moisture content where the over-all economics would justify such an installation. However, these units are not without their drawbacks because of high capital and operating costs, safety hazards and possible degradation of the product, and thus an alternative method of moisture reduction is highly desirable. After the various mechanical variables associated with filtration have been optimized, an examination of theory shows that surface tension and liquid viscosity are the only two remaining variables which might be altered to reduce moisture content. A lowering of the surface tension within the limits of normal wetting agent dosage results in a rather insignificant decrease in cake moisture content. Not until the dosage is increased to a point well beyond this limit is there an appreciable decrease in moisture. At these high dosage levels, interfacial tension is a major factor contributing to the appreciable moisture reduction obtained. Since no suitable method has been developed to recover and recycle this wetting agent, this phenomena is not of practical significance. On the other hand, a reduction in liquid viscosity has a pronounced effect on cake moisture. While it is readily apparent that one method of reducing liquid viscosity is to heat the entire feed slurry, it is equally apparent that this would not be an economic approach except, perhaps, in certain isolated cases. It does, however, suggest that water circuits should be designed to conserve heat as much as possible and to make use of any waste heat that may be available. The use of hot air as a heat carrying medium for drying porous materials on a filter has been practiced for many years. However, this method is restricted to materials with a high air rate in the order of 100 cfm/ ft2 because of the low heat release per unit weight of air passing through the cake. The normal fine coal filter cake has an air porosity far too low to make this a practical approach. Various types of radiant heating devices have been investigated and can significantly lower moisture content at reasonable thermal efficiency. However,

Jan 1, 1964

By R. Chanchani

It was reported earlier that francolite and dolomite from south Florida deposits cannot be selectively floated using conventional conditioning with sodium oleate as the collector. However, dolomite could be separated from francolite if the minerals were first conditioned at pH 10 followed by reconditioning at a lower pH. An optimum separation was achieved after reconditioning at a pH below 4.5. Reconditioning pH and collector concentration were determined to exert a major influence on the selectivity. Flotation, adsorption, and transmission infrared spectroscopic results are presented to elucidate the mechanisms underlying the observed selectivity.

Jan 1, 1986

The. Library of the above-named Societies is open from 9 A. M. to 10 P. M. except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and, photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 3, 1919

The Library of the above-named. Societies is open from 9 A. M. to 10 P. M. except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and publications of scientific and technical societies Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 5, 1918

By J. Parke Channing

THE production and use of copper in the world, like that of other metals, has been of slow growth. In 1880, production in the United States, was only about 60,000,000 lb. and the world's production 325,000,000 lb. Up to 1913 there was a gradual and regular increase in production; in 1912 the production was 1,250,000,000 lb. for the United States and 2,200,-000,000 lb. for the world. At the outbreak of the war there was a slight falling off, both in the United States and elsewhere, but when it was realized that the war was not to be a short one and that copper was one of the most important things for carrying it on, there was a tremendous increase in production every-where. Roughly speaking, the average production for the years 1916, 1917 and 1918 was very close to two billion pounds in the United States and three billion pounds in the world. WAR DEMANDS STIMULATED PRODUCTION Not only did the production of copper in the United States increase, but the same may be said of .all the base metals, particularly of zinc. Much of the zinc used by the Allies came from Australia, but had been smelted in Belgium and Germany, now closed to them. We were called upon to make good this lost supply and in feverish haste built new zinc smelteries and opened new mines. The armistice found the United States with a large surplus of copper on hand, variously estimated at from 800,000,000 to 1,000,000,000 lb. In addition to this surplus in the United States, there were considerable stocks in the hands of the Allies and also immense quantities of unused brass. To. complicate the situa-tion still further, the reclamation of old brass shell cases and other used material was instituted, still further curtailing the demand for new material. This situation was- not appreciated at the time and it was assumed, that the Central Powers would immediately come into the market ? replenish their exhausted stock of copper. During the war Germany had torn down copper trolley wires and roofs, and melted up bronze bells, doors, statues and other copper-bearing material to reclaim this metal for military purposes. But Germany-was unable or at least unwilling immediately to replace her copper substitutes.

Jan 1, 1923

By Jasper L. Stuckey

GEOGRAPHICALLY, North Carolina consists of three divisions, the coastal plain on the east, the piedmont plateau in the center, and the Appalachian mountain region on the west. Geologically, the State may be divided into two main divisions, an eastern or coastal plain region, and a western or piedmont plateau and mountain region. The eastern region is underlain with unconsolidated sands, clays, marls, and shell limestones varying in age from Cretaceous to Recent. The western region is, in general, underlain with gneisses, schists, slates, sheared volcanics, and igneous intrusives of Pre-Cambrian age. In the mountain and upper piedmont portion of the western region are several areas of irregularly metamorphosed sediments of early Paleozoic age. Throughout the piedmont plateau and a part of the mountain portion of the western region, important areas are underlain with igneous intrusives of late Carboniferous age. Along the eastern edge of the piedmont plateau are two narrow belts, trending northeast-southwest, underlain with sediments of upper Triassic age. Although North Carolina contains a

Jan 1, 1947

By J. W. Furness

THE utilization and collection of waste materials have gone on for centuries, and have become a habit of the human race. The degree to which the salvaging of waste plays a part in a nation's industry depends largely on the availability of raw materials within the political confines of the country itself, or its ability to purchase such material from outside. When purchase is necessary careful economical use of the raw materials results. These economies, as a rule, are represented by lengthening the life of the given article as well as much re-use. For many years the steel industry of Italy and Japan has depended largely on importations of scrap, yet both are important. As long as the expenses incident to the conditioning and marketing of materials manufactured from salvaged waste are less than the cost of virgin material, the salvaged material will be re-fabricated and in many cases will compete with primary materials. One of the most obvious methods for furthering the efficient utilization of our limited mineral resources is the salvaging of mineral wastes. This method, moreover, in¬creases the available supply of a given material. If the price depends on a balance of supply and demand and the recovery from wastes enlarges. the supply, there can be no question but that it influences the sales price of primary.

Jan 1, 1931

The Library of the above-named Societies is open from 9 A.M. to 10 P.M., except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on milling and metallurgical subjects; to determine the existence of mining maps, arid to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 10, 1916

Looking forward to growing demand for the output of the coal mines over the next decade, producers face serious problems in meeting the market. Among the difficulties are the Coal Mine Health and Safety Act of 1969, wildcat strikes, growing shortage of skilled and supervisory labor, pollution control and rising costs. The two-day program, planned by R. L. Frantz, covered all of these subjects and presented a few remarks on such wholesomely noncontroversial matters as ground support. A prediction of coal for electricity generation in 1980 was made by Philips amounting to 550 million tons, an amount equal to total output now, With respect to competition in this market, he said: "For the foreseeable future there is enough energy demand for all participating fuels." Banana oil conies not from bananas but from coal and science may just convert coal to meat loaf or some other surprising application may come out of research for product markets. Philips sees no revolution in mining methods although longwall mining will be expanded.

Jan 1, 1970

By Francis B. Foley

THE casting of steel in large molds brings into play all of the undesirable effects that result inevitably from slow cooling. The origin of the molten metal, whether basic or acid open hearth or electric furnace, has little if anything to do with the phenomena involved. If the quantity of molten metal to be cast in a single mold is large enough, there is very little one can do about it-the metal will cool so slowly that 'nothing one can do, other than to provide as good feeding as practicable from an adequate reservoir of metal in the sink head, will be of any avail. Recently we have had occasion to cast a 108-in. octagon ingot weighing 545,700 lb, necessitating the combining of metal from three 100-ton open-hearth heats. This is one of the largest ingots ever made. The body of the ingot weighed 448,800 lb, which includes a bottom pool of about 7500 lb of metal, and the sink-head weight was 96,900 lb, or about 18 pct of the total weight.

Jan 1, 1947

By Robert M. Rudio

Montana is leading the way in the field of mined-land reclamation with new laws and new ideas. The Montana Department of State Lands is combining new legislation and practical application techniques to all mining operations in the state. Road building, stream relocations, or settling systems can be designed to meet the environmental problems. Mineral exploration now requires a new and closer look at drill site locations, road gradients, and exploration tools. The problems and costs of land rehabilitation must be thoroughly understood by the exploration geologist in order to satisfactorily conduct exploration in Montana.

Jan 1, 1975

By George Evans

DURING the past ten or twelve years, the average reader of newspaper and magazine articles has been led to believe that enormous deposits of high-grade coal exist in the northland and that these can be mined for practically nothing. But much of the reputed glitter and attractiveness of Alaskan coals disappears when viewed at close range. Many areas of coal-bearing rocks are widely distributed geographically from Cape Lisburne, on Bering Sea, to Admiralty Island south of Juneau. Bituminous coal is found at Cape Lisburne, on the Bering Sea, at Five Finger Rapids on the upper Yukon, and at Herendeen Bay and Chignik Bay; lignite is found on the Kobuck River, along the Yukon River from points near the mouth to Tonakat, near Rampart, at Dawson, on the east shore of Cook Inlet, and in the Tanana Valley, 50 mi. south of Nenana. The Susitna and Matanuska Valleys contain coal ranging from lignite to anthracite, and in the Bering Lake district, there are coals ranging from semi-bituminous to anthracite. No effort will be made to describe all of these fields, but the writer wile confine himself to the four principal fields, namely, the Nenana field, in. the interior of Alaska, tributary to the Fairbanks district; the Matanuska, field, in the Matanuska Valley; the Kachemak Bay field on the east shore of Cook Inlet; and the Bering River field, east of the mouth of Copper River.

Jan 2, 1921