Search Documents

By Charles A. Anderson

The Bagdad copper deposit is of the disseminated type (porphyry copper) occurring in a quartz monzonite stock of late Cretaceous or early Tertiary age. This stock, located essentially at the intersection of two dike swarms, is the only one of several stocks cropping out in the area which is appreciably fractured and mineralized. Most of the rocks in the area are of pre-Cambrian age, but their structures have had no discernible influence on the copper mineralization. Hypogene alteration of the quartz monzonite includes the addition of quartz, orthoclase, and sericite and recrystalli-zation of biotite. The hypogene sulphides are pyrite, chalcopyrite, and molybdenite, the latter younger than the chalcopyrite. The late Cretaceous or early Tertiary igneous rocks, veins, and faults were controlled by northeast and northwest shear zones, the intersection of which marks the zone of appreciable copper mineralization. The minor mineralized fractures carrying the bulk of the copper have a preferred orientation parallel to the intersecting shears, and it is concluded that they are of tectonic origin rather than the result of shrinkage on cooling, crystallization, or mineralization. Supergene enrichment during late Tertiary or early Pleistocene time formed a chalcocite zone providing the minable copper ore. The enrichment was controlled in large part by northeast and northwest faults, prticularly at their intersection or where the faults are closely spaced. Introduction A major objective in a regional geologic study of a mining district is to determine whether any structural pattern can be found that has a bearing on the control of mineralization. The Bagdad copper deposit is of the disseminated type (porphyry copper) occurring in a.quartz monzonite stock which is located essentially at the intersection of two dike swarms (Fig 2). Of several quartz monzonite stocks in the area only this One is appreciably fractured and mineralized. The origin of the minute mineralized fractures in disseminated copper deposits has long been a challenging problem to the mining geologist, and evidence has been obtained to suggest that the mineralized fractures at Bagdad are related to a regional pattern of conjugate shears which also controlled the location of the dike swarms. The purpose of this paper is to Present this evidence and to emphasize the structural control of the supergene enrichment in forming a chalcocite zone that has provided the ore for the Bagdad mine. The field work on which these conclusions are based was done between October 1943 and August 1945, as a part of the copper investigations of the Goelogical Survey, U. S. Department of the Interior. The writer and his associates, E. A. Scholz and J. D. Strobell, Jr., have prepared a comprehensive report on the geology and ore deposits of the Bagdad area which will be published subsequently by the Geological Survey. Bagdad is located in west-central Arizona in Yavapai County. Ransome' divided the State of Arizona into three provinces: I? the plateau to the northeast; 111, the desert region to the southwest and 11, the moun-

Jan 1, 1949

By R. L. Rickett, W. C. Leslie

The influence of deoxidation practice, prior thermal history, and aging time and temperature on the strain-aging behavior of low-carbon open-hearth steels was investigated. The criterion of aging employed was the increase in yield strength in the tensile test, after straining and aging. Composition, prior heat treatment, and aging conditions were all found to be important in governing the strain-aging characteristics of these steels. THAT deoxidation changes the strain-aging propensities of low-carbon steels has been known for a long time, but there has been little agreement, and even contradiction, between results obtained by different investigators and between results obtained in the laboratory and in the mill. This investigation was begun in the hope that some of the uncertainties connected with the strain aging of commercial steels could be eliminated. In considering this problem, it was necessary to define strain aging and to examine the methods used to measure this property. Strain aging can be defined as the changes in properties of a metal or alloy with time, after cold working. The rate at which these changes occur increases as the temperature is raised above atmospheric. The requisite plastic strain is the principal distinction between strain aging and quench aging, the latter being due to precipitation from supersaturated solid solution. Strain aging is also characterized by rapid attainment of maximum hardness at high aging temperatures and lack of softening (overaging) at low aging temperatures. Several possible criteria of strain aging have been listed by Sachsl and by Davenport and Bain.' Because changes in mechanical properties are the most easily measured and the most commonly used, consideration of methods to be used in this investigation was confined to three tests: tensile, notch-impact, and hardness. Hardness tests are the most economical and easiest to perform, but produce only one measure of strain aging. Also, as pointed out by Felmly, Hartbower, and Pellini,³ hardness changes due to aging are not pronounced for steels containing more than 0.15 pct C. Notch-impact tests require careful preparation of large numbers of specimens. Above and below the transition temperature the test lacks sensitivity; furthermore, it is extremely difficult to impart a uniform strain to the specimens, followed quickly by aging and final testing; machining must generally take place after straining. For these reasons, the tensile test was selected for use. Although this test requires a considerable expenditure of time, labor, and money in preparation of the specimens and performance of the test, more information can be gained than from any other single mechanical test, information which includes upper and lower yield points, yield-point elongation, tensile strength, strain-hardening exponent, reduction of area, and elongation. Low and Gensamer' and Schwartzbart and Low5 lso used the tensile test, taking the increase in flow stress after straining in tension and aging as a measure of strain aging. In our work, as in theirs, each specimen was strained an arbitrary amount, sufficient to pass through the

Jan 1, 1954

SMALL things are customarily moulded in two ways (unless they have undercut parts which hold them in the moulds); that is in clay, or with natural or which artificial earthern powder made in halves in either wooden boxes or bronze frames. This also depends on whether the object is larger or smaller. Now if you wish to mould with moist clay, you must grease your relief with oil or pig fat; apply a dusting of charcoal, ashes, or cuttlebone on it; or gild or silver it dry with gold, silver, or tin foil. Then, first make with moist and somewhat firm clay a plate as, thick and large as can conveniently hold your relief, and carefully set the latter halfway into this and let it dry. Then, greasing or dusting it again, make the other half. When both are well dried, take out your relief and at the top make its gates and vents. If plastering is needed, do it. Finally, bake the halves, fit them together, and tie them well, as you wish, using the procedure that I taught you in the discussion of brass. But if one has to make a large quantity of works of one kind, he should for the sake of convenience use the method with powder [120] because it is short and requires less time and expense. Therefore if you wish to do this, you need to have several pairs of bronze frames or wooden boxes, higher than half the relief that you wish to mould, and of convenient length. On a flat board always keep half of one of these frames full of powder that has been slightly moistened for moulding, as I told you, so that by pressing with the ends of the fingers and with the hand it holds together as well as possible. Level it off with a cutting tool and when leveled put a flat board over it and turn it over. Turn it on to a dusting of ashes so that it will not stick, dust it on the other side, and remove the excess by blowing it off Then mould the thing that you wish to mould, pressing it halfway in once or twice, always taking it out and putting it back again. Then the other frame is fitted in its place and filled with earth by pressing and squeezing it carefully. Then it is leveled off on the outside with a sharp tool as you did with the other part, and then one of the parts of the frames is lifted up with the point of a knife or some other tool and,

Jan 1, 1942

By W. L. Austin

At the Steptoe metallurgical plant, where ore of the Nevada Consolidated Copper Co. is beneficiated, a small copper-leaching annex has been in operation treating flue dust from roasting-furnace dust chambers, together with a siliceous oxidized ore. This leaching plant was designed to obviate smelting low-grade siliceous flue dust, which interfered with the operation of the reverberatories by forming a blanket on the charge. The major portion of the copper content of the flue dust accumulating in the upper chambers of the roaster flue, and at the stack, is water soluble, and also contains much free sulphuric acid and soluble sulphates. It was found that sufficient acid could be obtained by mixing this material with water to provide a lixiviant for leaching the siliceous copper ore mentioned. This was the sole source of the lixiviant used in the operation to be described. An analysis of the flue dust showed it to be composed as follows : Per Cent. Copper.............................................. 3.00 siO2................................................. 23.41 Fe................................................... 4.08 CaO + MgO......................................... 2.72 Al203................................................ 0.07 Free H2S04........................................... 19.94 SO3 combined as sulphate.............................. 25.10 H2O combined with the sulphates....................... 10.67 0................................................... 2.50 Total................................... 97.49 Copper soluble in dilute H2SO4.......................... 2.56 The oxidized ore, locally known as carbonate, has the following composition:

Jan 1, 1915

By Gilbert Cady

EXTENSIVE Sampling of coal in Illinois during the past 10 or 12 years by the State Geological Survey, in cooperation with various organizations, such as the U. S. Bureau of Mines, the University of Illinois, and the Illinois Cooperative Mining Investigations, has made possible the delineation of two areas of low-sulfur coal in the southern part of Illinois. The sulfur content is less than 1.25 per cent., so that, if otherwise suitable, these coals can be employed for metallurgical uses and for the manufacture of water-gas and retort gas. One of these areas is small and lies in Jack-son County, near Murphysboro, the other is much larger and includes a large part of the famous Franklin County field. A small area of No. 2, or Murphysboro, coal has been worked for many years near the town of Murphysboro, Jackson County, Ill. In two mines, at least, the coal has a sulfur content of less than 1.25 per cent. It is doubtful, however, whether this field will ever be a source of large tonnage as the total area underlain by low-sulfur coal in workable thickness is probably less than 15 sq. mi. (24.14 sq. km.), and a large part of it has already been worked out. The location of the area of low-sulfur coal in the Franklin County field is shown in the accompanying map. The small area underlain by the Murphysboro low-sulfur coal is shown near the town of that name in the central part of Jackson County. The larger area lies in the west side of Franklin County, extending also about 6 mi. (9.65 km.) south into Williamson County, about 4 mi. (6.43 km.) west into northern Jackson and western Perry County, and northward an undetermined distance into Jefferson County. All but the northern limit of the area is fairly well defined by sampling in numerous mines. The inner cross-lined area is underlain by coal having less than 1 per cent. sulfur, the outer boundary surrounding the area Underlain by coal having less than 1.25 per cent, sulfur.

Jan 7, 1919

By Leo F. Reinartz

The history of steelmaking in the United States is a fascinating story of determination, sudden tragedy, exploitation, and inventive genius rolled into one gigantic plot. Mr. Reinartz' flowing interpretation of the progress made in the last one hundred years is being presented in a series of four articles. THIS is the Age of Steel. We live in a mechanized era. Our everyday lives--everything we see or do-are organized and influenced by this versatile metal. Our industries, our farms, our homes, and our transportation-yes, our vocations and avocations, or luxuries and necessities-all are dependent upon smelting iron and making steel. Take away iron and steel and soon our vaunted civilization would revert to a primitive existence. These metals, often in crude forms, have been known for thousands of years. Down through the ages, until about one hundred years ago, steel was made laboriously, and at high est, in small batches. During those years, methods of manufacture did not change very much. Over long periods of time only warriors, royalty, and wealthy people could afford to use articles made of iron or steel. History has recorded that the nations which were expert in iron and steel manufacture, and had access to rich iron-ore deposits, were the leaders in war or in peaceful pursuits. At the end of the 18th century, thirteen struggling American colonies had broken not only the political shackles that bound them to Great Britain, but also many of the economic bonds. They had showed their skill, Yankee ingenuity, and energy by making iron and steel articles for their own use. After the Revolutionary War, more and more hardy American pioneers pushed westward through the Allegheny Mountain passes and down the rivers into the fertile Ohio River and Kentucky country. Demands for articles made of iron increased. The iron industry on the east coast grew and prospered. As this trend continued, iron industrialists moved their plants westward to be near the large deposits of high-grade coal in western Pennsylvania, eastern Ohio, and nothern West Virginia. They also desired to use the local iron ores and water resources of those areas. Blast furnaces and ironworks were built in the Pittsburgh, Youngstown, southern Ohio, and northern West Virginia districts. In 1810, the United States produced 53,908 gross tons of cast iron and 917 tons of steel. Iron ore discovery A white man first discovered large deposits of iron ore in the northern Michigan and Lake Superior country in 1844. One year later, the Sault

Jan 1, 1961

By John Bonar

A switch to refractory-type slurry pump linings has significantly reduced maintenance costs arising from liner failure at a Missouri lead mill. The pumps routinely handle a slurry consisting of 79 to 81% solids with occasional tramp iron, and are subjected to intense abrasion which previously wore out rubber liners in anywhere from three days to two months. Average liner life at the 1.5-million-t/y (1.6-million-stpy) operation was 30 days. Experimentation with mild steel liners and even manganese steel liners failed to extend liner life beyond two months.

Jan 3, 1978

By Giovanni Barla, Stefan H. Boshkov

This paper examines the application of gelatin mixture models to the study of factors such as gravity effects, tectonic and residual stresses, anisotropy, physical nonlinearity, time-dependent behavior of the rock mass and connectedness of the geologic space. The technique of calibrating gelatin mixtures proposed by Richards and Mark in 1966 is applied to the particular problem considered. Similitude relationships between model and prototype are discussed with reference to the constitutive equations describing the physical behavior of the rock mass. The interaction between two openings in a linearly elastic medium, under conditions of plane strain, is used as an illustrative example with the view to describing the history of stress and deformation changes on the rock medium and lining around a slusher drift while undercuts are made in block caving. The prediction of the displacement, stress field and mode of fracture associated with a given rock structure, its initial stress field, and its physical properties is essential to rock mechanics and ground control. The basic approach is to assume the rock mass to behave as a continuous, homogeneous, and isotropic medium. The classical theory of elasticity is the simplest theory based on such a concept. Specification of the elastic constants, the initial state of stress in the ground, and the boundary conditions on stress and displacement allows one to predict stress and displacement within the body. Subsequently, provided that a criterion which governs rock fracture under various stress conditions has been established, a stability analysis of the rock structure can be performed. A natural extension of the present knowledge consists of removing some of the simplifying assumptions which characterize the analytical solutions based on the classical theory of elasticity. Complex geometry, the significance of tectonic and residual stresses, anisotropy, physical nonlinearity, time-dependent behavior of the rock mass and connectedness of the geologic space are some of the important factors which are neglected in the classical approach. A better insight into the real problem can be attained with either the finite element method of stress analysis or an experimental technique. The former has already been applied with success on several occasion 1-4 and is destined to render great service in the field of rock mechanics and ground control. The latter, which will be considered in this paper, has been used extensively in applications too numerous to be enumerated. Experimental technique involves either prototype testing, if the area to be studied is accessible, or model testing. Two- and three-dimensional photo-elastic analyses are very convenient means of obtaining the stress distribution in models of complex geometry. In general, such analyses are confined to studies of stress fields around openings which are sufficiently far removed from the surface boundary so that the stresses in their neighborhood are practically equal to those produced by an initial uniform stress field; i.e., so that gravitational effects are negligible. There are, however, many rock structures where these effects must be taken into account to attain a more realistic representation of the problem. Surface and near surface rock structures, systems of openings interacting with one another, and structural components loaded only by their own weight are some of the obvious examples. This paper was written to show how factors neglected in the usual analysis based on the classical theory of elasticity, can be taken into account when gelatin mixture models are used inconjunction with photoelastic methods. The interaction between two openings in a linearly elastic medium, under conditions of plane strain, is used as an illustrative example, with a view to describing the history of stress and deformation changes on the rock medium and lining around a slusher drift while undercuts are made in block caving. The birefringence of gelatin mixtures has been known for some time. A series of experiments were carried out by Rossi in 1910,5 but after that very

Jan 1, 1970

By I. S. Levy, J. L. Brimhall, B. Mastel

Specimens of' Hastelloy X-280, a low-cobalt version of the solid-solution- hardened nickel-base alloy Hastelloy X, were given a series of thermomechanical treatttzents. They were then Lensile-tested at room temperature and 1350°F. The Microstructures of the specimens tested at 1350°F were studied by electron Microscopy. Microscopy showed that dislocation tangling, caused by the cold working, mas still in evidence after aging-for 24 hr to temperatures as high as 1550oF. (Cr, Mo)23 C6, (Fe, Mo)6 C'. as well us an unidentifiable phase precipitale due to the combination of the thermomechanical treatments and subsequent tensile strain. The room -temperature and 1350°F tensile properties show a general increase ill strength and decreccse in ductility with increusing cold-work level. This is due to the dislocation taangling-. PerLurbatiot~s to this general trend occur- due to solid-solution weakening at the higher cold-work levels as a direct result of the preciplitation reactions. THE requirements for corrosion resistance and high-temperature strength place nickel-base alloys among the more promising materials for advanced nuclear reactor applications. However, when these alloys are irradiated at service temperatures, they generally suffer severe embrittlement'" and reduction in rupture life.3 Certain experimental treatments resulted in improvements in the tensile and stress-rupture properties of Hastelloy X-280, a solution-hardened nickel-base alloy.' To provide a basis for understanding these improvements, unirradiated tensile specimens were examined by electron microscopy. The results are reported in this paper. EXPERIMENTAL DETAILS Material. Hastelloy X-280, a low-cobalt version of Hastelloy X, is a member of the solution-hardened class of nickel-base alloys. The Hastelloy X-280 was obtained from 4- and 1-in: thick plates in the mill -annealed condition. Table I gives the chemical composition of the material as reported by the National Spectrographic Laboratories. ~x~erimental Treatments. Plates of suitable size, 12 by 3 by 1 in., or by + in., were cut under a water jet from the stock material and examined ultrasonic -ally for homogeneity of grain size and absence of voids. The acceptable plates were solution-treated at 2150°Ffor 1 hr and air-cooled. These plates were then reduced in thickness by cold rolling 0, 10, 15: or 20 pct along the original rolling direction. The plates were machined into buttonhead tensile specimens with a gage diameter of 0.125 in., with a gage length of 1.125 in., and with their tensile axes parallel to the rolling direction. The specimens were examined for quality of finish with a penetrant dye, ultra son ically checked for voids, and finally given a dimensional tolerance check with an optical comparator. The acceptable specimens were aged for 24 hr at either 1000" or 1500 F and air-cooled. These specimens were then held at 540°F in a water loop for approximately 18 days to qualify as controls for similar specimens irradiated under the same conditions of time, temperature, water chemistry, and flow rate. Table U summarizes the treatments. These treatments were investigated to establish whether prior precipitation and stabilization of carbide phases at strain sites within the matrix could reduce the amount of carbides available for precipitation at grain boundaries during service. Tensile-Test Conditions. Specimens were tested to fracture at room temperature or 1350 F in air on an Instron tensile-testing machine at a crosshead speed of 0.05 in. per min. The time for the furnace to reach equilibrium at 1350°F was approximately 30 min; soak time prior to testing was 15 min; and test duration was approximately 5 min.

Jan 1, 1968

By James C. Bayles

The ideal pressure-tube is obviously the one which combines the greatest strength with the least weight of material consistent with the uses for which it is designed or employed. The inside of the pipe is the first concern of the engineer. It should be cylindrical, smooth, and of the requisite capacity for the purpose in view. It should be in lengths as great as can be oonveniently handled, so that the couplings may be as few as possible. With the walls of the tube the engineer has no further occasion to concern himself than to make sure they are adequate to carry the internal and external pressures to which they will be subjected. It is as true of a pipe as of a truss, that when it is strong enough to give the requisite factor of safety, nothing is gained by having it stronger. Anything more than this means dead weight, which has to be paid for many times, first as material, and again and again in the costs of transportation and handling, until it reaches its place in the trench or on supports. In use it must be and remain tight against all leakage, and must sustain whatever is placed over or upon it, or suspended from it, without deformation or injury. Finally, in addition to meeting all the immediate requirements of service, it must possess qualities of durability which warrant a reasonable expectation of a long life of usefulness. The wise engineer no longer regards it as reasonable to depend upon mere bulk of its own material for the protection of a metal as readily impaired or destroyed by oxidation as iron or steel. The metal must have a coating which will be and remain impervious and indestructible. When all these conditions are met, we have as near an approach to the ideal tube as can be attained with the materials now available for their manufacture. Steel wed constructively, to the best advantage, meets these requirements most perfectly. Gold alone would do it better. If we search through the whole list of metals and alloys we find nothing available which so perfectly meets the requirements as a pipe material as steel. Mr. Hamilton Smith, Jr., in a paper on the expedients adopted on

Jan 1, 1891

By J. R. Lucas, H. E. Rutherford

The primary objective of this research was to evaluate the feasibility of ultrasonic testing for the purpose of analyzing the structure and properties of rock material. A secondary objective of this study was to determine experimentally the elastic wnstants of various rock specimens with the use of ultrasonic equipment. Elastic constants can definitely be determined quickly and accurately by ultrasonic investigation. With proper equipment there are indications that ultrasonic waves could be utilized in the detection of flaws, such as fractures and planes of weakness, measurement of thickness, and the study of structure of rock material. Ultrasonic principles have been applied in many industries for the purpose of determining the structural characteristics of various materials. The principal applications of interest here are detecting flaws, measuring thicknesses, and determining elastic constants. The main advantage of ultrasonic analysis is that it is nondestructive. It also has extreme sensitivity, high penetrability, good accuracy, rapid response, and the necessity to have access to only one side of the specimen. These various applications and advantages lead one to think that ultrasonic principles might be applied to rock material in situ for purposes of analyzing its structural characteristics. Therefore, the primary objective of this research was to evaluate the feasibility of ultrasonic testing for the purpose of analyzing the structure and properties of rock material. A secondary objective of this research was to determine experimentally the elastic constants of various rock specimens with the use of ultrasonic equipment. The term ultrasonics is given to that branch of acoustics dealing with periodic sounds whose fre- quencies are above the audible range or above approximately 15,.000 to 20,000 cps. The first practical production of this high frequency sound was made possible after World War I due to developments of electronically controlled sound wave sources. At the present, the maximum practically attainable ultrasonic frequency is approximately 1000 megacycles per sec. Sound waves of sufficiently high frequency can be made to travel in a beam with little spreading. Therefore, such a beam can explore a material and detect nonhomogeneities in it by reflection. This is the principle of the ultrasonic reflectoscope invented by F. A. Firestone' in 1942. An ultrasonic beam, on pulse-penetratink a solid material medium, produces an echo when it strikes a flaw which has different acoustical properties than the surrounding medium. This echo can be detected by the same transducer which sends out the original pulse. This principle is the basis of the important industrial techniques of nondestructive ultrasonic testing of metals and other solid material. Later developments in the field of ultrasonic testing of solid material have been mostly improvements in equipment and instrumentation. To date, most of the industrial applications of ultrasonic analysis of solid bodies have been in the aircraft, electrical, and nuclear energy fields on the nondestructive testing of metal. The one solid material similar somewhat to rock material, upon which some work has been done to apply ultrasonic testing techniques to study structural integrity, is concrete. Jones and Gatfield3 briefly summarize this work on concrete. Their basic conclusion was that the strength of concrete was a function of the change of the longitudinal sound wave velocity in the concrete. Only recently has any extensive study been made to apply ultrasonic testing techniques to rock material. Lutsch studied rock material by an ultrasonic pulse method to determine the extent and degree of fracture of rock faces. Lutsch states that the number of observed reflections is a measure of the degree of fracture and that only ultrasonic waves are able to detect fractured zones subjected to high pressure. Suzuki, Sasaki, and Siohara5 studied the characteristics of the sonic wave in rock for propagation over a wide range of wave lengths. They indicated that, in rock, the propagation constant and attenuation of the

Jan 1, 1962

By E. Horton Jones

INTRODUCTION WE have endeavored in the following "sheets" to give the unit construction costs derived from the building of the Arizona Copper Co.'s new smelter, Clifton, Ariz., starting in February, 1912, and completing February, 1914. 1 In Chapter I-Unit Costs-are to be found the most elementary total unit costs which the accounts provide for. They are usable in the Clifton district. Here too are found the percentages to be added to an estimate for Engineering and General Expense. In Chapter II-Comparative Costs-these elementary costs have been classified, averaged and reported as labor and material unit costs. In such form the labor unit costs, when properly applied to similar conditions as these under which they were derived, are usable anywhere. The material unit costs are better disregarded for more accurate estimates and replaced by a newly priced bill of material. In Chapter III Composite Costs are given. They are unit costs built-up from several elementary units, and likewise units of larger dimensions and simpler application, valuable for

Jan 7, 1914

By Mark O. Halverson

In this paper, some applications of remote terminal computer time-sharing to mining geophysics are discussed. Examples are presented and evaluations are made. The evaluations are based largely upon one and one-half years experience with the General Electric Mark I and Mark II systems. In both systems, a terminal is placed at the user's location. The terminal consists of a teletypewriter and a paper tape system. Input is on paper tape or keyboard. The output is printed on paper and may also be placed on paper tape if desired. Available languages consist of BASIC, FORTRAN and ALGOL. The time-sharing system is considered very useful. In large part this is because the terminal is available for use as the need arises, much like a slide rule or calculator. Useage is varied. Geophysical field data can be put on paper tape and be computer reduced, for the most part by clerical personnel. Time-sharing is excellent for statistical studies. The system is adequate to generate geophysical parameter values derived from simple models of the subsurface and to make comparisons with field data.

Jan 1, 1969

By William P. Blake

IntroductioN.............989 The Blake stone- Breaker Prize.......989 Great Labor-Saving Inventions.. 990 I. Biographical NoticE OF the Inventor......990 II. Former Methods of Breaking Stone......992 Ragging and Spalling......... 992 Cornish Rolls..........993 III. Construction of the Blake Stone-Breaker.. .. 993 The Lever.Pattern.........994 The Eccentric Pattern.........997 The Challenge Pattern......... 999 The Monarch Pattern.........1001 The Multiple-Jaw Pattern........1001 Movable Dies for Jaws......... 1004 Cheek.Plates,..........1007 IV. The Capacity OF Blake Breakers......1007 Position and Feeding of Breakers...... 1008 V. Gyratory Jaw Crushers.........1010 The Gates Rock- and Ore-Crusher......1010 The Comet Crusher.........1010 VI. Some Unusual Forms OF the Breaker......1010 The Smith Hydraulic Pattern.......1012 The Forster Crusher.........1012 The Stafford Crusher.........1013 The Gates Crusher.........1013 The Dodge Pattern.........1013 The Rawson Crusher.........1014 The Duplex Breaker.........1015 Booth's Modification of Wedge-Block......1015 Marsden's Eccentric Pattern.......1017 The Lancaster Machine........ 1017 VII. Combined Crushing and Grinding Impracticable,. . 1018 The Hanscomb Machine ...1019 Howland's Crusher and Pulverizer..1020 The Oliver Crusher and Pulverizer..1021

Jan 1, 1903

By F. Twyman

PART I.-QUALITATIVE, SPECTRUM ANALYSIS THOSE chemists (they are still greatly in the minority) who use the spectroscope, use it very often, and find it almost indispensable. As a means of detecting minute quantities of the metals it is unrivalled. A metal can be readily distinguished in the presence of any other element, compound, or mixture without the necessity of separation. The qualitative analysis of the metallic constituents of a substance, which, the spectroscope gives so easily, is a sure basis for planning a chemical analysis. As the determination of each element proceeds the purity of precipitates maybe checked as often as desired. If, possessing these advantages; the spectroscope has been neglected in general chemistry, it is not surprising that it was neglected in metallurgical chemistry; for many of the impurities which are of industrial interest, even when they are present in a metal or alloy in small quantities, are not then always easily detected by the examination of their visible spectrum. The history of the development of the art has been given in Bureau of Standards Scientific Paper No. 444.

Jan 1, 1928

By John C. Branner

Inquiries are frequently made concerning the chalk- and clay-beds of Arkansas, usually with a view to the manufacture of Portland cement. The chalk-deposits were first described by Professor R. T. Hill in the annual report of the Geological Survey of Arkansas for 1888, vol. ii., pp. 153-162. Since the publication of that report I have visited localities then unknown, and have accumulated considerable additional information concerning these deposits, dl of which is brought together in the present paper. My report upon the clays of the State has never been published; only a few of the more conveniently available deposits are mentioned in the present paper. The Chalk-Deposits. Stratigraphic Position of the Chalk.—The chalk-deposits of Arkansas belong to rocks of Cretaceous age. The Cretaceous rocks are confined to a single definite area in Southwest Arkansas. Beginning on the Ouachita river, a little northeast of Arkadelphia, its southern or upper margin follows a line about five miles southeast of, and approximately parallel to, the St. Louis, Iron Mountain and Southern Railway from Arkadelphia

Jan 1, 1898

As knowledgeable men in the industry know, a mineral occurrence is found through prospecting but an ore deposit is "made" -made through, first, imaginative and effective exploration; thence through efficient engineering, sales and management. There are two main phases of exploration-reconnaissance and target investigation-each of which can be further divided into two additional stages (see accompanying table). The search for a new ore deposit within a known and geologically mapped mining district involves only the last two stages, whereas the search for a new orebody in a virgin geologic environment involves at least three stages and often the full sequence. Of course, some of the exploration stages may be bypassed depending on available results of previous mineral surveys and/or exploration by individuals, business concerns, and governments.

Jan 10, 1967

By George R. Elliott

Methods are presented for measuring and comparing "degree" of water drive, and for observing the control that rate of withdrawal exerts over decline of reservoir pressure. Degree of water drive is studied from pressure-production curves of 10 reservoirs; the method used to present these comparatively is to convert cumulative oil production from barrels to percentage of ultimate. Degree of water drive is also represented by a "water-encroachment factor," representing barrels of water influx per pound-month per acre-foot of oil reservoir. Pressure-production curves for the water-drive reservoirs after a period of declining pressure show a diminishing angle of slope, in some cases to the point where pressure ceases to decline or where it even increases; the shapes of these curves are in marked contrast to the dissolved-gas type of curve, which shows a general trend toward zero pressure at ultimate oil recovery. Yearly rate of oil production in percentage of ultimate oil recovery is correlated with pressure decline. The correct rate of production of oil with its associated gas and water sustains pressure in reservoirs having a high water-encroachment factor. For reservoirs having a low water-encroachment factor, it is necessary to inject the produced water and even inject large volumes of water from an outside source. The discussion of the actual reservoirs is preceded by a general review and is followed by a substantial bibliography. It is now generally accepted that water drive is capable of yielding 60 to 80 per cent of the original oil in place in most reservoirs, as compared with 20 to 40 per cent for dissolved-gas drive. There is no need to question the importance of controlling a reservoir in order to take advantage of such an efficient mechanism. What is a water-drive reservoir? Oil reservoirs usually combine two or more of the four basic mechanisms: dissolved-gas drive, gas-cap drive, water drive, gravity drainage. A water-drive reservoir is one in which water advances to take the place of the oil and gas produced. When the oil withdrawal rate is sufficiently low, the water will tend to maintain pressure. The maximum effectiveness is attained when the water follows the oil withdrawal so closely that little or no decline in pressure occurs. Oil in its underground reservoir is associated with water. This water is significant in the production of the oil according to the source of supply and the permeability of the surrounding formation. As oil is produced and the pressure is lowered, water can move in to replace the oil. With adequate supply and sufficient permeability, actual movement takes place on an extensive scale. The first movement of water takes place by expansion of the water and its associated fluids. While this expansion is of little importance in some fields, in others it is sufficient to supply all of the energy required for the production of oil. When a pressure differential has been established

Jan 1, 1946

By George R. Elliott

Methods are presented for measuring and comparing "degree" of water drive, and for observing the control that rate of withdrawal exerts over decline of reservoir pressure. Degree of water drive is studied from pressure-production curves of 10 reservoirs; the method used to present these comparatively is to convert cumulative oil production from barrels to percentage of ultimate. Degree of water drive is also represented by a "water-encroachment factor," representing barrels of water influx per pound-month per acre-foot of oil reservoir. Pressure-production curves for the water-drive reservoirs after a period of declining pressure show a diminishing angle of slope, in some cases to the point where pressure ceases to decline or where it even increases; the shapes of these curves are in marked contrast to the dissolved-gas type of curve, which shows a general trend toward zero pressure at ultimate oil recovery. Yearly rate of oil production in percentage of ultimate oil recovery is correlated with pressure decline. The correct rate of production of oil with its associated gas and water sustains pressure in reservoirs having a high water-encroachment factor. For reservoirs having a low water-encroachment factor, it is necessary to inject the produced water and even inject large volumes of water from an outside source. The discussion of the actual reservoirs is preceded by a general review and is followed by a substantial bibliography. It is now generally accepted that water drive is capable of yielding 60 to 80 per cent of the original oil in place in most reservoirs, as compared with 20 to 40 per cent for dissolved-gas drive. There is no need to question the importance of controlling a reservoir in order to take advantage of such an efficient mechanism. What is a water-drive reservoir? Oil reservoirs usually combine two or more of the four basic mechanisms: dissolved-gas drive, gas-cap drive, water drive, gravity drainage. A water-drive reservoir is one in which water advances to take the place of the oil and gas produced. When the oil withdrawal rate is sufficiently low, the water will tend to maintain pressure. The maximum effectiveness is attained when the water follows the oil withdrawal so closely that little or no decline in pressure occurs. Oil in its underground reservoir is associated with water. This water is significant in the production of the oil according to the source of supply and the permeability of the surrounding formation. As oil is produced and the pressure is lowered, water can move in to replace the oil. With adequate supply and sufficient permeability, actual movement takes place on an extensive scale. The first movement of water takes place by expansion of the water and its associated fluids. While this expansion is of little importance in some fields, in others it is sufficient to supply all of the energy required for the production of oil. When a pressure differential has been established

Jan 1, 1946

By AIME AIME

SCANDINAVIAN countries seem somehow to furnish an amount of talent and leadership far be- yond their population and among them Sweden is possibly at the top. The United States has many eminent citizens born in the latter, country or who are of Swedish descent and the engineers may claim their full share. In fact, the number is so large that a flourishing Swedish-American Engineering Society has been formed, including a number of A. I. M. E. members. Dr. Waldemar Lindgren is more scientist than engineer, though his work in economic geology has contributed directly to the development of many mines, and he is the valued- adviser of a number of our larger companies. Probably he, himself, values most highly the contributions he has been able to make to scientific theories of the occurrence and genesis of ore deposits. His fellow scientists have placed upon these the high mark of approval by electing him to the National Academy of Sciences, and Princeton University in 1916 recognized his position by conferring on him the degree of Doctor of Science.

Jan 1, 1931