Search Documents

By Charles H. Moore

In the study of the properties of rutile pigments it became apparent several years ago that certain physical and optical properties could not be determined on particles of pigmentary size. Since reflected light is the dominant type which reaches the eye from small particles, the true color of pure rutile was not known. Most rutile pig-ments are acicular in habit, elongated parallel to the "c" axis. It was considered important to know the nature and tone of light transmitted, for example, by a basal plate. Further, as shown by spectrophotometric curves, there is a very strong absorption of light of 4000 A as measured on particles with random orientation. It would be interesting to see whether this absorption position varied with predetermined and selected orientations. Also, since the behavior of titanium pigments in a vehicle is important, a knowledge of the surface wettability of single crystals by various media should prove very fruitful. Finally, the optical properties of rutile are such that it should show, in a single pure crystal, greater fire and brilliance than the diamond. Mineralogists had long speculated that this would be the case and curiosity was strong to produce a single crystal large enough to cut. In light of the above, a project was initiated for the formation of single crystals of rutile. Method of Formation of Rutile Single Crystals Fortunately, purification of TiO2 produced from both titanium tetra-chloride and titanyl sulphate solutions had reached the stage where spectro-graphically pure starting material could be made. Spectrographic analysis of the feed material used in the initial experiments is compared with the present feed material in Table 1. It is apparent that the present large scale purification is approximately as good as the original experimental, small scale purification. Verneuil1 produced synthetic ruby and corundum in 1904 by the well-known flame fusion process, which today bears his name. Except for mechanical improvements the present commercial production of synthetics by flame fusion is essentially unchanged from his initial method. His burner consisted of an inner orifice through which was fed the feed material and oxygen. Surrounding this was a larger outer orifice through which was fed hydrogen at lower pressure. This arrangement consists then of a lance of oxygen burning in an atmosphere of hydrogen. The proportions of hydrogen to oxygen usually used in corundum production is about 3:1, providing there is sufficient temperature to reach the 2050.°C required for the fusion of alumina. From work done in the Titanium Division Laboratories2 and from the published work of Erlich3 it was known that rutile appears to lose oxygen near its melting point and that it would not be possible to grow single crystals in a strongly reducing environment. Consequently, in order to determine whether single crystals could be grown at all, an Airco oxygen-acetylene torch with

Jan 1, 1950

By W. M. Myers

MINERAL Economics is the most recent profession to be recognized as a separate division of the mineral industries. It has originated from the increasing awareness of the importance of the economic aspects of industries concerned with discovery, extraction, and utilization of minerals. It is concerned with the interrelated fields of economics and technology. The individual trained in economics alone cannot qualify. The curriculum in the School of Mineral Industries at The Pennsylvania State College was approved in May 1946, and enrollment begun in September of that year. Due to the transfer of advanced students from other courses, particularly metallurgy and electrical engineering, it was possible to graduate the first seniors in June 1947. The next class was graduated in February 1948. From experience derived from placing these graduates in industry, and from information supplied by prospective employers, valuable data have been obtained in the organization and operation of the course of study.

Jan 1, 1948

By C. H. Herty

Almost every metallurgist who has given the Howe Memorial Lecture has had a personal contact with the distinguished gentleman to whose honor this hour is devoted. Unfortunately for me, such personal contacts were not possible. However, in the preparation of a thesis on the open-hearth process, one of my earliest tasks was to make a survey of the literature, and it was from Professor Howe's Metallurgy of Iron and Steel that I drew a number of references to previous work which formed the foundation for my reading. In his volume there is such a complete exposition of the then current thought on the subject of slags and on their role in the elimination of phosphorus from steel that I feel no hesitation in discussing in this Howe Lecture the subject of "Slag Control." In the present era of close specification, the drive for uniformity of product, and the close inspection of the product and of the cost sheet, the utmost efforts must be made to control the steelmaking variables to the best advantage of the steel producer. One of the major variables is the slag in the furnace and its effect upon the composition and quality of the metal. What advantages are to be gained from slag control? In the broad sense the advantages must be tremendous, because the very foundations of good steel melting are based on "shaping up" the slag to a point where, with proper temperature, the heat is ready for the final additions. Every melter works toward these ends through his experience with innumerable heats of steel. The elimination of undesirable constituents such as phosphorus and sulphur is entirely a matter of slag composition and physical nature, a point well known for over half a century. The role played by the slag in assisting in proper heat transfer from roof and flame to the steel has been equally well known. In more recent years there has come the problem of oxygen control in the more accurate gauging of additions for making high-grade rimmed steel for the new strip mills, and in the deoxidizing additions for grain-size control and cleanliness of forging steels, both carbon and alloy. In this problem the oxidizing characteristics of the slag are of prime importance.

Jan 1, 1940

By C. H. Herty

Almost every metallurgist who has given the Howe Memorial Lecture has had a personal contact with the distinguished gentleman to whose honor this hour is devoted. Unfortunately for me, such personal contacts were not possible. However, in the preparation of a thesis on the open-hearth process, one of my earliest tasks was to make a survey of the literature, and it was from Professor Howe's Metallurgy of Iron and Steel that I drew a number of references to previous work which formed the foundation for my reading. In his volume there is such a complete exposition of the then current thought on the subject of slags and on their role in the elimination of phosphorus from steel that I feel no hesitation in discussing in this Howe Lecture the subject of "Slag Control." In the present era of close specification, the drive for uniformity of product, and the close inspection of the product and of the cost sheet, the utmost efforts must be made to control the steelmaking variables to the best advantage of the steel producer. One of the major variables is the slag in the furnace and its effect upon the composition and quality of the metal. What advantages are to be gained from slag control? In the broad sense the advantages must be tremendous, because the very foundations of good steel melting are based on "shaping up" the slag to a point where, with proper temperature, the heat is ready for the final additions. Every melter works toward these ends through his experience with innumerable heats of steel. The elimination of undesirable constituents such as phosphorus and sulphur is entirely a matter of slag composition and physical nature, a point well known for over half a century. The role played by the slag in assisting in proper heat transfer from roof and flame to the steel has been equally well known. In more recent years there has come the problem of oxygen control in the more accurate gauging of additions for making high-grade rimmed steel for the new strip mills, and in the deoxidizing additions for grain-size control and cleanliness of forging steels, both carbon and alloy. In this problem the oxidizing characteristics of the slag are of prime importance.

Jan 1, 1940

By A. W. Allen

The technological study of the treatment of gold and silver ores has been largely responsible for the phenomenal strides which have marked the progress in this branch of metallurgy during recent years. In no other application of science to industry is system more imperative at every stage; correct formulation of result is only second in importance to efficiency of operation. Progress in method, on the other hand, is mainly due to individua1 initiative aided by the work of technical journals and metallurgical societies. There still remains a field for profitable discussion, and it is my intention to deal with some inconsistencies of expression common to a number of writers on the subject; and also to draw attention to the false impressions created by a statement which may, possibly, be only unintentionally misleading. I also take the opportunity of tracing the source of both metallurgical and economic result; and would question the desirability of the methods usually employed in arriving at a final statement. In the first place, I wish to deal with the question of extraction. This term may mean anything or nothing, and it is often used to mislead. In a report of a mining engineer as to the result of operations subsequent to the remodeling of a treatment plant prominence was given to the statement that the extraction had amounted to 91 per cent. On examination it was found that only a small percentage of the so-called extraction was calculated on actual bullion return, a proportion being figured from the gold left in the zinc boxes, and not recovered. In addition to this, a proportion of the extraction was said to be due to gold in concentrate. As there was no conrcentrating apparatus on the property and as concentration did not form a part of the scheme of treatment the matter was investigated, with the result that the concentrate, of lower gold content that the original ore, was found to be the result of an inegcient pumping system which failed to provide for the whole of the battery product delivered to it. The balance was stacked and, although itself of no marketable value, the gold content was allowed to form a basis of extraction figures. The illustration may be extreme, but it will serve to show to what lengths an engineer may go in the mutilation of the most vital term in metallurgical technology.

Jan 1, 1915

By C. K. Leith

QUOTING from Dr. Richard T. Ely:1 "Conservation, narrowly and strictly considered, means the preservation in unimpaired efficiency of the resources of the earth; or in a condition so nearly unimpaired as the nature of the case, or Wise exhaustion, admits. And broadly considered, it means more than the word itself implies, for it naturally includes an examination of methods Whereby the natural inheritance of the human race may be improved; and still more broadly considered, and as used in popular discussion, it includes a treatment of the effects of productive conservation methods upon distribution. "Conservation means a sacrifice of the present generation to the future generations Whenever it is carried too far. There is a sharp limit to the economic sacrifice that we may reasonably ask the private person to make for even the present Welfare, and the limit is still sharper when we come to consider the interests of future generations." In a paper on the iron ores of America, presented to the Pan-American Scientific Congress at Washington, I have emphasized the fact that the reserves of iron ores in the two Americas are enormously in excess of the requirements of the present generation, in fact, so large that no shortage is to be anticipated for many generations in the future; that a large part of the value of iron ores is put into them by man's efforts to make them available. This fact is fundamental for the intelligent consideration of- policies of conservation as applied to iron ore. As I interpret it, this fact makes it practically unnecessary that the present generation should make any especial sacrifice for future generations in the way of conservation of its iron-ore resources. Even if we were disposed to look forward to a period of 100 or 200 years, with a view to insuring the welfare of the people living at that time, it is doubtful whether any procedure we could now formulate would materially help them in the matter of iron ores, so large are the reserves available. In order that an appeal for conservation may be effective it must obviously favor the welfare of the present or immediately following generations; it must promise benefits to general and individual welfare during a period within the range of comprehension of the average man.

Jan 2, 1916

By Marcel R. Daly

EUGENE COSTS, Calgary, Alberta (communication to the Secretary*).¬This new theory to account for the accumulation of commercial deposits of oil and gas, is deliberately and admittedly based on the hypothesis that the origin of these products is organic. Mr. Daly says (page 1142), "Should the organic origin of the petroleum that is found in pools be granted, the following interpretation is offered for the mechanics of its accumulation." But suppose the origin thus accepted by definition be incorrect, then what becomes of the diastrophic theory, Mr. Daly's interpretation? As Mr. Daly remarks himself (same page), "It is obvious that the history of petroleum will have to be entirely different, dependent upon its origin, either from emanations coming from the depths, or from organic decomposition in the strata themselves." Then why should one propound a theory, through which he is endeavoring to trace the history of petroleum, by starting with a definition of its origin? The origin should be the deduction, the forced conclusion of the theory, and not its starting point. Facts alone should be considered first, in any theory worth the name, until sufficient proofs have accumulated to permit of the deduction of a complete explanation for these facts. This would lead one to the origin through a real theory founded on facts, and not based on a preconceived idea perhaps true, but possibly fanciful. Mr. Daly's way can only lead on one road, namely the organic road, and, I repeat, it may be the wrong road. In the case of the petroleum deposits, as .I have endeavored to show in several papers on the subject, to which the reader may refer, the facts clearly lead to the force conclusion that their origin is not one of accumulations of hydrocarbons at first disseminated in the sedimentary strata but the reverse process of subsequent local infiltrations and impregnations of hydrocarbon emanations from the depths. This new theory, therefore, founded on, an erroneous conception of origin cannot be a help in the solution of the petroleum' problem, not any more than were the anti-theory or the hydraulic theory, both of which were also based on the same error, although Mr. Daly is inclined to think that the authors of these two theories did not accept the misconception boldly enough (page 1142). -

Jan 12, 1916

By G. St. J. Perrott

AN explosive of, balanced composition might be expected, on first consideration, to develop maximum propulsive strength.1 This hypothesis is based on the assumption that an excess of oxygen would act simply as an inert material with a consequent lowering of flame temperature, also that a deficiency of oxygen would tend toward incomplete reaction of the combustible materials, thereby preventing development of the full strength of the explosion. Actually, however, it can be shown both theoretically and experimentally that an explosive having a certain oxygen deficiency will develop the greatest propulsive strength. This fact has been known to the technical staffs of explosives manufacturers for many years, but it has not always been recognized by explosives engineers in the field. For example: There: is a fairly widespread opinion that the wrapper of a stick of dynamite is merely a container for the explosive and that it plays little if any part in the development of propulsive strength. Actually, it can be shown that the wrapper enters fairly completely into, the explosive reaction. In the case of most gelatin dynamites, a given weight of explosive from which the wrappers have been removed will develop considerably less strength than the same weight of explosive plus wrapper, in spite of the fact that the latter combination contains less weight of the actual explosive ingredient. It can also be shown that a cartridge 7/8 in. in diameter may be stronger, weight for

Jan 1, 1928

By Samuel Doak

THE utilization of rotary kilns, of the well-known cement type, for the preparation of iron ores, for the blast furnace, has become of considerable economic importance within the past 10 years in certain localities, notably those where the native ores are lean. Such kilns may be used simply for the agglomeration of ores too fine to be charged into the blast furnace (i.e., ores whose loss in the dust catchers is excessive, and whose fineness is detrimental to the working of the furnace), or for the desulphurization of lump and fine ores the sulphur content of which does not exceed 6 or 7 per cent. The desulphurizing action can be combined with that of agglomeration provided the kiln is sufficiently large. Other processes have been developed for the same purpose, but while I am not able to draw a comparison between them by reason of lack of sufficient data, it is safe to say that the kiln, if properly dimensioned for the character of ore to be treated, will compare favorably in its results, both as to economy and quality of product, with any other process. It is not, however, as well adapted for the treatment of flue dust, as is a sintering operation, on account of the large percentage of fine coke contained therein. Any combustible entering the kiln at its feed end renders the process very much more expensive and unsatisfactory on account of the difficulty of controlling the temperature, also because of the rapidity with which long "rings" form, due to the increased heat at the cooler end of the kiln. The greatest value of the kiln at present is in the treatment of pyrites cinder; that is, the residue from pyrites ore after the extraction of the greater part of the sulphur. This cinder, while high in iron content, has too much sulphur remaining in it to be allowed to form a large part of the blast-furnace burden, without further treatment. It will range in metallic iron from 42 per cent., representing a very low-grade cinder, from a domestic pyrites, to 64 per cent. of the residue from the best Spanish ore, and the corresponding silica content will vary from the maximum of about 25 per cent. to 1 ½ per cent. The residual sulphur depends largely on the type of burner used in the original desulphurization. In general, the leanest original ores retain the greatest amounts of sulphur. In

Jan 9, 1915

By Wolfgang Pietsch

Direct Reduced Iron is a product obtained during solid state reduction of iron oxides into metallic iron. General chemical and physical characteristics of all direct reduced iron materials result in a noticeable reoxidation tendency and a relatively low ignition temperature. As most of the chemical reactions are exothermic, normally heating occurs and if water is present hydrogen evolves. Dry direct reduced iron deactivates quickly in air but is still reactive if it comes into contact with moisture. Because of these characteristics, special requirements are necessary for safe storage, shipment, and handling. In an effort to improve this situation passivation techniques were and still are being developed. The paper discusses the properties of direct reduced iron, presents past experience with storage, shipment, and handling of MIDREX® Iron, a direct reduced iron material produced in the MIDREX® Direct Reduction Process, and evaluates benefits derived from different passivation techniques.

Jan 1, 1978

EARLY this year the Board of Directors announced that, through the generous gift of past-president W. L. Saunders, a gold medal to be awarded for distinguished achievement in mining had been estab-lished. At the December meeting of the Board the medal committee reported that it recommended that the first medal be awarded to David William Brunton for "development and exposition of the principles and prac-tice of ore sampling; for systematic daily mapping of mine geology; for the Brunton mining compass; and for engineering achievements in connection with great tunnels." The formal presentation of the medal will be at the din-ner, on Feb. 16, in connec-tion with the annual meet-ing. Mr. Brunton, like several other prominent Institute members, was born in Can-ada, and came to the United States when he was twenty-four years old. He had then been in civil en-gineering work for three years and after a year more of it, deciding that mining was more attrac-tive he spent two years at the University of Michigan doing advanced work in geology a n d chemistry. His first mining engage-ment was with the Dakota and San Juan Mining Co., at Mineral Point, Ouray County, Colo. That was in June, 1875, and the young engineer had to travel 230 miles by trail from the then nearest railroad station at Pueblo. Having to come out because the company did not get in enough supplies to last through the winter he became metallurgist for the Hunt, Douglas & Stewart Co., at Georgetown, Colo. When the Hunt and Douglas plant proved a success, H. A. Taylor, the father of Mr. Brunton's later partner, Frank M. Taylor, engaged him to build the Clear Creek Reduction Works. Eighteen months later he built the Native Silver Mining Co. mill at Caribou and a year later a mill at Silver Peak, Nev., that was so successful that the principal owner shut it down to freeze out the minority stockholders. The winter of 1879 found him at Leadville where he did engineering work for the Robert E. Lee, Duncan, Wolftone, A. Y. & Minnie, and Dinero mines, eventually becoming manager of the Colonel Sellers. In 1886 he was called in on apex-side-line litigation at Aspen with the result that he went there to develop the mines for economic and legal pur-poses, and later became the manager of three of them. His most notable piece of work there was the driving of

Jan 2, 1927

Located 19 km (12 miles) north of the Carlin gold mine and 43 km (27 miles) north of Carlin, Nevada, is Carlin Gold Mining Company's Bootstrap mine. This deposit is similar in character to the Carlin ore, except it occurs in the upper plate formation of the Roberts thrust fault rather than in the lower plate rocks. The deposit was discovered over 50 years ago and operated on a small scale in the early 1960s using vat cyanide leaching. Newmont Mining Corporation acquired the property in 1967, and from an open pit mined 650,000 mt (717,000 st) of ore which was trucked to the Carlin conventional cyanide plant. (See Gold and Silver Cyanidation Plant Practice by F. W. McQuiston, Jr. and R. S. Shoemaker, Society of Mining Engineers, AIME, 1975. ) With the same grade of ore, the gold recovery by conventional methods is somewhat lower than that of the Carlin ore, even with a finer grind. Leaching tests were first conducted by the United States Bureau of Mines in 1968; and in 1971, ‘72, Carlin conducted extensive cyanidation investigations by bottle testing, simulated heap leaching in tall columns, and small scale pad heap leaches. Gold extractions ranged from 55% to 95% with low reagent consumptions. In 1974, a 545 mt (600 st) heap leach test was made at Carlin on pit-run low-grade material assaying 1.37 g per mt (0.04 oz per st). In a six week period the extraction of gold was 47.57'0. Carlin uses atomic absorption analyses on cyanide leach liquors to determine potential leach ore grade rather than fire assaying because it gives a more practical assessment of leach recovery than does fire assaying, which accounts for the total gold content. Before open-pit mining was started, plans were made to heap leach, the ore at Bootstrap which was too low grade for transport to Carlin. The topsoil outside of the designed pit area overlaid ancient lakebed clays which were found suitable for compaction to form an impervious base on which the dumps to be leached could be placed. By using the cost of truck haulage and milling at the Carlin plant and the price of gold 'at that time, a cutoff grade was established which resulted in the gold content of the first 150,000 mt (165,000 st) of the heap leaching ore being 1.51 g per mt (0.044 oz per st). An additional 500,000 mt (552,000 st) of lower grade material, assaying 0.96 g per mt (0.028 oz per st), is available for leaching as economics permit.

Jan 1, 1981

By Ferid Kromer

This paper is the first in a series which will describe geology, mining methods, and production costs of some, of Turkey's more important minerals. In this paper the economically significant minerals-chromite, meerschaum, and magnesite-of the Tagtepe district are described. The cost data presented are believed by the author to be the first made public on Turkish chromite mining.

Jan 1, 1950

By S. Stutz

Three years ago, at the Philadelphia meeting, in February, 1881, the author had the pleasure of presenting to the Institute a paper on coal-washing machinery.* Since that time many new machines, with important improvements and labor-saving apparatus, have been introduced, the construction and description of which may be of interest to some of the members of the Institute. By referring to the above-mentioned paper, and more especially to Plate IV., representing a vertical section of a coal-washer, it will be noticed that the bottom of the plunger-box B is made level or horizontal, and supports a spring-buffer F for the purpose of limiting the down-stroke of the plunger P and receiving the impacts of the latter. Althongh the construction of the box, in view of these impacts, received from the start the proper attention (the bottom of the chamber 3 being made of three thicknesses of 3-inch planks, resting on 6-inch sqnare columns), yet, through careless working of the machinery, without the necessary water in the box, it proved in several instances not strong enough, and had to be changed. To prevent such interruptions in future, it became necessary to devise some means for relieving the machine from the impacts of the plunger altogether. This has been accomplished by the arrangement shown upon Plate I. of this paper, representing a new waesher; and not only has the difficulty been overcome, but also sorne other advantages have been obtained, as will be seen further on. The compartments +, A' of the separator-box have been set upon heavy cast-iron brackets B, leaving sufficient space below the bottom for the buffer F and the sediment-valve K. By means of the plunger-rod 6 passing through the stuffing-box s to the outside, and provided at its lower end with a shoe a, the impacts of the plunger are now transmitted from the buffer F directly to the foundation. At the same time a better guide for the plunger P in its up and down movement has been obtained. The plunger of the former machine had only the guide I and the yoke Y, whereas the new machine has an additional guide in the stuffing-box s, thus preventing wear and friction of the plunger against the lining of the box. Further-

Jan 1, 1884

By P. St. J. Perrott

AN explosive of balanced composition might be expected, on first consideration, to develop maximum propulsive strength.1 This hypoth¬esis is based on the assumption that an excess of oxygen would act simply as an inert material with a consequent lowering of flame temperature, also that a deficiency of oxygen would tend toward incomplete reaction of the combustible materials, thereby preventing development of the full strength of the explosion. Actually, however, it can be shown both theoretically and experimentally that an explosive having a certain oxygen deficiency will develop the greatest propulsive strength. This fact has been known to the technical staffs of explosives manufacturers for many years, but it has not always been recognized by explosives engineers in the field. For example: There is a fairly widespread opinion that the wrapper of a stick of dynamite is merely a container for the explosive and that it plays little if any part in the development of propulsive strength. Actually, it can be shown that the wrapper enters fairly completely into the explosive reaction. In the case of most gelatin dynamites, a given weight of explosive from which the wrappers have been removed will develop considerably less strength than the same weight of explosive plus wrapper, in spite of the fact that the latter combination contains less weight of the actual explosive ingredient. It can also be shown that a cartridge 7/8 in. in diameter may be stronger, weight for

Jan 1, 1928

By M. L. Brashears, R. G. Slayback

The host dolomite of the Pine Point lead-zinc ore is a prolific ground-water aquifer that occurs locally under watertable and artesian conditions. Mining schedules and severe climate require rapid and thorough dewatering of open pits. Pumping-test methods, common to ground-water supply studies, were applied to dewatering design for a model ore pit in 1968. Procedures for testing and design at other ore bodies were established and have been carried out successfully by mine personnel. At the inception of ground-water studies, parts of ore bodies were below prevailing ground-water levels by 35 to more than 150 ft. Movement of ground water through the coarsely recrystallized dolomite occurs largely through fractures and solution openings. Because the overburden deposits consist mainly of glacial till, it is estimated that the recharge to the aquifer is about 25% of the 13-in. annual precipitation. Natural groundwater flow is northeastward toward Great Slave Lake. Background data included extensive diamond drill hole logs and cores and static level data for a number of ore pits. An ore pit, known as N-42, that required 40 ft of dewatering was selected for the initial application of the pumping-test method. Production wells, cased with 14in. pipe, were drilled to a depth of 300 ft on the rim of the ore pit. A suitable pattern of observation wells was obtained by lining 21/8-in. diamond drill holes with perforated electrical conduit. A two-stage pumping test

Jan 1, 1973

By J. Chipman, T. P. Floridis

The equilibrium of gaseous H2O-H2, mixtures with liquid iron is used to establish the activity coefficient of dissolved oxygen as log f o = — 0.20 [%O]. Discrepancies in earlier work are explained or eliminated. Additions of cobalt, molybdenum, tungsten, and platinum increase the activity coefficient of oxygen whereas copper and gold decrease it. THE importance of dissolved oxygen as a refining agent in liquid steel has led to a number of studies of its thermodynamic properties. It is the purpose of this paper to examine the effects of a number of alloying elements on the activity of oxygen in the steel bath. As a preliminary to the study of the effects of alloying elements, it seemed desirable to examine certain minor discrepancies in the published data on the properties of oxygen in simple iron-oxygen solutions. The activity and free energy of oxygen in liquid iron were studied by chipman1 in 1933 by means of the reaction h2(g)+-o = H2O (g);K; = PH2O/PH2[% O] [1] The data were in fairly good agreement with calculations from results on the similar reaction CO (g) + O- = CO2 (g); K2 =P CO2/P CO [% O] [2] which had been obtained by Vacher and Hamilton2 as an incidental part of their study of the reaction of carbon with oxygen dissolved in the melt. It was found that the equilibrium ratio k1 was not a true constant but varied with the oxygen concentration in the manner shown in Fig. 1, which is copied from the original paper. This early observation has been refuted in subsequent work but is confirmed in the present paper, and an explanation of the discrepancy can now be presented. In Fig. 1, the two points on the extreme right were disregarded in drawing the

Jan 1, 1959

By Samuel M. Dunaway

INTRODUCTION ASARCO Incorporated purchased the East Tennessee Zinc Mines of the American Zinc Company and commenced operating on November 29, 1971. Presently, three mines are operating producing 6620 t/d (7300 stpd). The ore mined is sphalerite which occurs In lower Ordovician carbonates of the upper Knox Group and occurs in open space and fracture filling. Orebodies range from 3 to 46 m (10 to 150 ft) thick with dips from flat to 20º. The mining method is random room and pillar modified by shrinkage and bench stoping. Like other mining departments, the mining group at the Tennessee Mines Division is constantly looking for methods to improve productivity and safety and to reduce mining costs. This involves testing new equipment, trying new ore extraction ideas and making mining plant alterations to meet changes in operating conditions. The areas of change that will be described in this paper are longhole raising, jumbos and LHD loading, shaft sinking, conveyor transport of ore and sublevel haulage developments. LONGHOLED RAISES Raise driving has always been a hazardous occupation for miners and today it is becoming more difficult to get competent people for this kind of work. This problem has led us to seek an easier, safer way in which to excavate raises. The first longhole raises were excavated in the early 1970's using a Gardner-Denver air trac equipped with a PR-123 rock drill. The machine used 38 mm x 244 cm (1 ½ in x 8 ft) round rods with rope

Jan 1, 1977

By Benjamin S. Lindsey, James Norman

BARITE (BaSO4) is the most important industrial barium mineral from the standpoint of quantity consumed. In 1938 the amount was 365,000 tons. Its uses are numerous, some of the more important being in the production of pigments, as an inert filler in a wide variety of products, as a weighting material in oil-well drilling muds, in the manufacture of some kinds of glass, and in the production of barium chemicals. The barite studied in this investigation occurs as the massive variety in a shale replacement formation near Magnet Cove, Ark. It is intimately mixed with quartz and small amounts of iron oxide and residual shale. Complete liberation of barite and quartz is not obtained when the rock is ground to 100 per cent through 325mesh. The crude rock with which all test work was done assayed 85.1 per cent BaSO4, 11.11 per cent Si02, and 2.85 per cent R2O3. Its specific gravity was 4.03. It was found in the course of the investigation that the barite contained a small amount of uniformly distributed carbonaceous material, so intimately dispersed that it could not be seen with the microscope, but gave a definite gray cast to the barite concentrates. The color of the barite in polished sections of the crude rock ranged from gray to almost black, while finely ground powder was a reddish gray. The reddish hue was due to the iron oxide present. In 1939, under the supervision of Oliver C. Ralston,* the Bureau of Mines, in cooperation with the Milwhite Company, of Houston, Texas, undertook to study the flotation of barite from Magnet Cove, Ark. Flotation of several southern barite ores had already been investigated by the Bureau of Mines.1 The Magnet Cove barite was unique, however, in that it had to be ground to such an extremely small particle size for liberation. The flotation of nonmetallic minerals in the presence of a large amount of slime is usually very difficult, and when done is an innovation calling for conditions different from those under which granular material is separated. LABORATORY FLOTATION WORK Preliminary investigation showed that the flotation reagents recommended by O'Meara and Coe1 for separating barite and siliceous material were suitable, but much larger quantities of reagents were required to separate such finely divided material. Moreover, it was found that careful control of the frothing was necessary. When oleic acid and sodium silicate were used a voluminous froth was observed at the beginning of a test, and toward the end there was not enough froth to effect complete recovery of barite. The addition of pine oil as a frother gave proper frothing for the duration of the test, and the substitution of coconut fatty acid (crude lauric acid) for oleic acid produced a more heavily burdened froth. Two different paper-mill fatty-acid products were tested

Jan 1, 1941

By GUY C. RIDDELL

ZINC, manganese, and aluminum received attention at the two nonferrous metallurgy sessions at the Annual Meeting. L.P. Davidson, general superintendent of the rebuilt Monsanto zinc plant, described its operation, which reflects Polish practice and is really a combination of electrolytic, Waelz, and retort procedure. Briefly, it embraces leaching of roasted concentrate with sulphuric acid, electrolysis of sulphate solution using Tainton lead-silver anodes with ?goulac? added to the electrolyte, treatment of tailing in Waelz kilns, and retorting of the recovered zinc oxide, casting furnace dross and residues. Recovery is good, equipment and maintenance costs low. Ferrate zinc that might be lost in the electrolytic process appears to be recovered as oxide in the Waelz treatment.

Jan 1, 1942