Search Documents

By J. F. Gormley

Drill pipe, and the connections used to join the pipe together, have had a long history of development and improvement. With the growing use of high tensile-strength pipe, the rotary shouldered connections used to join the lengths of drill pipe have become more critical. Fatigue-type failures of rotary-shouldered connections, or tool joints, have become a cause of much conern to operators and manufacturers. Most fatigue tests on tool joints have been made on the basis of bending moment applied vs number of cycles, rather than on the basis of stress vs cycles. A desire to learn more about the nature of stress in a tool joint due to bending caused a rather intensive experimental study to determine what actually happens to cause fatigue failure. It was known that a tool joint with insufficient make-up torque was subject to early fatigue failure. Therefore, the establishment of the relationship between make-up torque and allowable bending moment would enable a testing engineer to better correlate the results of various tests. The problem of calculating the stress in a tool joint due to an applied bending moment was complicated by: the effect of unknown stress concentrations; the applicability of the well known formula S = Mc/I; and the question of whether to use the combined cross section of the pin and box in calculating the moment of inertia I. TEST EQUIPMENT The test equipment consisted of the following. 1. A lathe modified to act as a fatigue machine for full-size tool joint or drill-collar specimens. 2. An adapter plate bolted to the headstock of the lathe and into which a short adapter was screwed. 3. Tool-joint pins on sections of drill collars bucked into the adapter. 4. A hydraulic load cylinder which rested on the bed of the lathe and applied bending moments to the joints. 5. Paper-backed strain gauges (FAP-12-12, 1/8-in. gauge length and A-5-1, 1/2-in. gauge length). 6. Eastman 910 contact cement for bonding gauges to joint and Epoxylite 222 waterproofing. 7. A 12-position switchbox, SR-4 bridge balancing unit connected to an SR-4 strain indicator to read the gauge output. 8. A four-channel Sanborn recorder, Model 150, was used as the readout instrument for part of the testing. The fatigue machine was well suited as a loading device. Because of the long lever arm available, the change of moment with distance was small; consequently, the vertical shear stress was small, less than 300 psi. Some difficulty was experienced with the hydraulic load cylinder at high bending moments due to leakage. The strain gauge equipment was simple and quite reliable. A 41/2-in. extra hole (E. H.) joint with "as machined" threads and shoulders and a 2 7/8-in. internal flush (I. F.) joint with copper-plated threads and shoulders were selected for testing because of their common usage in the field. In addition, the 4 1/2-in. E. H. was suitable because it had an inside diameter large enough to permit the insertion and accurate positioning of strain gauges without using special jigs, while the 2 7/8-in. I. F. joint required much lower bending loads to cause separation of the shoulders of the joint when made up to the recommended torque. The joints were made to standard API specifications, except for very small bevels on the box and pin shoulders and cylindrical stress-relief grooves added to the pins. Larger bevels would have

By J. F. Myers, F. M. Lewis

C. G. McLACHLAN*-I have read this paper with considerable interest and wish to congratulate the authors on the care with which they carried out their experiments and for the detailed sizing data they have presented. 011 the other hand I do not feel that these data establish their contention that "with other factors the same, the work accomplished in a fine crushing rod mill is directly proportional to the rotating speed." My reason for making this statement is that their conclusion is based on the percentage of minus 65 mesh material produced at each of the speeds at which their tests were run. The rod mill is, however, not a fine grinding machine and therefore figures based on minus 65 mesh production are figures outside the range at which it operates to best advantage. Further, if rod mill performance is to be judged on the production of such material it should have been established that a rod mill will produce it as effectively as a ball mill. To check this last point I have gone over some of the rod and ball mill grind-ing figures for our Waite-Atnulet operation and find that the ball mill at that property produces more minus 65 mesh material per horsepower than the rod mill. Moreover, this comparison is even more favorable to the ball mill if it is limited to minus 100 mesh production. It therefore seems to me that the most satisfactory basis on which to try to com-pare the performance of the rod mill in the present case is by taking a weighted average of all the new surface produced per horsepower. W. H. Coghill3 has published data which can be applied to the sizing figures presented by the authors, and if this is done the units of new surface per horsepower produced in the Tennessee tests are as follows: Admittedly the increment of increase in new surface per horsepower shown in the foregoing figures is not great, but its trend is nevertheless definitely in favor of slower speed operation, for the conditions under which these particular tests were run. I also feel that some information regarding liner contour should have been given as I think it will be found that a mill which is equipped with liners which lift the rod load can be run at a slower speed than a mill in which the liners are comparatively smooth. J. F. MYERS and F. M. LEWIS (authors' reply)—The position taken by Mr. McLachlan is to be respected even though we are all aware of the faults of surface considerations. As he points out. the increment of increase is very small. It is so small in fact that for all practical purposes it does not conflict with the conclusions of the paper. The authors appreciate Mr. McLachlan's comprehensive study of the data.

Jan 1, 1950

By H. W. Gillett

CLYDE WILLIAMS has reminded me that in the fall of 1929, gave, in MINING AND METALLURGY, an account of the hopes and aspirations of Battelle Memorial Institute, which was then just swinging into initial operation; and that therein I remarked that B.M.I. should stand, as well, for Better Metallurgical Industries, since helping to better them was the Institute's aim. So he has suggested that some of the betterments of the past fifteen years might well be listed. A yearly summary of progress comes pretty close to the ultimate in futility, for everything proved of value in that year had its inception in earlier years, and everything really new has still to be proved. Plenty of things hailed as wonderful achievements for that year, by some enthusiasts invited to contribute to the summary, turn out in later years to be inglorious flops. But over a decade and a half, betterments that are really such become self-evident, and recounting some of them can be done without guesswork or wishful thinking. An inventory of what was known and utilized in 1929 compared to what is now known and used is not too hard to make. Perhaps the most clear-cut picture of what is known and used at a certain date is drawn by the handbooks, textbooks, and equipment catalogs of that date, with scientific periodical literature forecasting what knowledge may later be used when it is verified and assimilated. The tools available for production or for research limit the application of old and the finding of new knowledge.

Jan 1, 1945

By AIME AIME

THE 123d meeting of the Institute was held in New York Feb. 14 to 17, 1921. The total registration was 1199, as compared with 1138 at the New York meeting in 1920. The weather was a strange and welcome contrast to that of last year, when New York was buried under six feet of snow as the result of the fiercest blizzard in its history. This year there was no snow, and the weather was said to be much more like an Arizona winter than New York. A complete program of the Technical Sessions is on p. 9. The discussions of the papers presented will be published in pamphlet form as soon as possible and will be noted in MINING AND METALLURGY in the usual way.

Jan 1, 1921

By B. D. Lichter

The lattice parameters of zirconium and zirconium-oxygen solid solutions (hcp) were determined from measurements of back-reflection X-ray photograms obtained at 29°C using a symmetrical focussing camera. The following linear equations between parameters (c,a) in angstrom units (10-8 cm) and atom ratio (m) of oxygen to zirconium were obtained: c = 5.14764 + 0.2077m a =3.23168 + 0.1099m. The linear equations given are valid over the range 0 to 5 at. Pct 0. The accuracy of individual parameter measurements approaches the limiting accuracy determined by the spectral broadening of the incident characteristic radiation, and exceeds the accuracy of previously reported values. THE present work was undertaken in order to determine the lattice parameters of zirconium-oxygen solid solutions with an accuracy that allows quantitative determination of oxygen in zirconium. The results indicate that this is possible if very careful measurements are made, since the parameter change is only a few hundredths of a percent per at. pct 0.1, 2 In the present investigation the desired accuracy was achieved with large-grained samples using a back-reflection focussing camera and maintaining good temperature control during exposure. In addition a digital computer was used for calculation of the parameters by means of an analytical extrapolation.37 Suitable diffraction photograms were obtained from large-grained samples by using a modification of the technique described by Graf and Monteil.5 This consists of simultaneous rotation and oscillation of the specimen about two mutually perpendicular axes during exposure. Whereas, normally the upper limit of grain size is about 50 µ for useable diffraction photograms, this technique allows extending the upper limit of grain-size to exposure of a single crystal. EXPERIMENTAL Preparation of Alloys for X-ray Diffraction—Zir-conium, designated as hafnium-free, Westinghouse "Grade 1," was swaged from l/2-in.-diam crystal bar to 3/8-in.-diam rods. Substantially all of the hydrogen was removed from the zirconium by annealing at 1200°C in a high dynamic vacuum. The rods were then swaged to 0.2 in. diam without intermediate annealing, and 2 in. lengths were cut for alloying with oxygen. Samples for chemical analysis were taken from portions of the rods between each 2 in. length. Chemical analysis of the dehydroge-nated zirconium is given in Table I. Commercial tank oxygen (99.5 pct 0) was condensed in a liquid nitrogen-cooled trap, and part of the condensate was slowly reevaporated into 5-liter storage flasks. Nitrogen remained as a reactive impurity, and the calculated maximum increase in nitrogen content after a 5 at. pct 0 addition to zirconium was 50 ppm by weight. However, chemical analyses of several of the prepared alloys indicated that the maximum increase in nitrogen content was 10 ppm. The storage flasks, a Sieverts-type gas burette and manometer, and associated traps, pumps, and pressure gauges were connected through a glass high-vacuum manifold to comprise the gas addition system. A fused silica tube, connected to the mani-

Jan 1, 1961

By B. S. Crocker

Pebble grinding was used at Lake Shore Mines in 1949. A full description of experimental evidence and test plant results was published in 1952 1 and further operating details in 1954 2.' In more recent years the term autogenous grinding has been coined and is now frequently seen in the technical literature. Autogenous crushing and/or grinding covers any grinding mill in which the larger pieces of ore are made to grind the fine pieces; the crushing and grinding may be either dry or wet. This discussion deals only with wet autogenous grinding, and only in the fine grinding part of the circuit, i.e., from 6 mesh to 92 pct —325 mesh. The term pebble milling could apply to fine autogenous grinding in which the pebbles are made from the ore itself, or it could also refer to grinding with pebbles, such as flint pebbles, from a source outside the mine. The first mill to use screened ore to grind the ore (1949) was Lake Shore Mines, Kirkland Lake, Ont. Pebbles were screened from the jaw crusher discharge and used in 5x16-ft tube mills which had been converted to 6 ft 8 in. by 16-ft grate discharge pebble mills. The same general practice was adopted the following year by the Wright-Har-greaves Mine in Kirkland Lake. Shortly after that the Neptune Mines in Nicaragua started correspondence with the writer concerning the possibility of using screened ore for grinding in their plant. They first ran some plant-scale tests which confirmed the Lake Shore findings, with the ultimate result that their plant was successfully converted in 1956 to an autogenous grinding plant. In 1957-1958 the writer was successful in converting the grinding plant of Renabie Mines in northern Ontario to autogenous grinding. In all these plants the existing grinding equipment was converted, usually by expanding the diameter of the shell to make the change from steel grinding to ore pebble grinding mills. In all the above plants primary grinding was done in either small rod mills or ball mills. These mills first reduced the pebble mill feed to about 6 mesh. The final grinding in the pebble mills varied from 75 pct —200 mesh to 92 pct —325 mesh. At Lake Shore three stages of pebble milling were used, with a different size pebble in each stage. In other parts of the world interest was being shown in this form of grinding, and in March 1952 the writer had some correspondence with the mill staff at Outokumpu in Finland, with regard to the pebble system used at Lake Shore. At Stockholm in 1957 the account of the crushing and grinding system at Outokumpu was presented in a paper by H. Tanner and T. Heikkinen.V his is the only ore grinding plant that does not use grate discharges on its pebble mills; trunnion discharges equipped with heavy reverse spirals retain the pebble load. The first new mill designed to use screened ore as a grinding medium was the Bicroft mill at Bancroft, Ont., which began operation in the fall of 1956. In 1957 this plant was followed by similar installations at Faraday Mines, also in the Bancroft area, and the North Rankin Nickel Mines in the North West Territories. In 1958 the Dyno Mill at Bancroft was converted, using the same type of grinding. Since all these plants, designed by Kilborn Engineering (1954) Ltd., were originally planned as pebble grinding mills, they were able to take full advantage of the latest design and technique. They are neat in appearance and very efficient and easy to operate. Effect of Ore Hardness: It is often commented that this type of autogenous grinding applies only to hard siliceous ores. Experience has shown that this is not so. In the past ten years the author has had an opportunity to test more than a dozen ores, several of which were quite soft. One of these was shale. The softer ores actually make better looking pebbles than the hard ores. These soft ores produced no particles in the intermediate size range which could not be ground by the largest pebbles in the mill charge. Slabby ores, such as shales, make a suitable pebble for the —6 mesh grinding. It is not generally recognized that for fine grinding a spherical medium is not essential or more efficient. Another frequent objection to pebble grinding is the belief held by some operators that there is too much variation in the hardness of their particular ore to make it acceptable as a source of pebble media. Experience has also shown that this is not a serious problem at all. The variation in pebble load due to changes in the ore hardness is nothing like as great as most people would expect, and the method used for feeding the ore and controlling the the load in the mills is more than sufficient to take care of daily variations in ore hardness. This point

Jan 1, 1960

By R. J. Stevens

The Roan Antelope Smelter commenced operations in October, 1931. As originally designed, its equipment consisted of one reverberatory furnace, 120 X 25 ft, two Peirce-Smith converters 12 X 20 ft, and one straight line casting machine. Since that time the following additions have been made: One reverberatory furnace 120 ft X 28 ft ('934) One reverberatory furnace 95 ft X 28 ft (1943) Two 12 X 20 ft Peirce-Smith converters (1934 and 1938) One 13 X 30 ft holding furnace (1938) One straight line casting machine and 2 ladle tilting quadrants (1934) The metallurgy of the smelting process is comparatively simple. However, there are several features of operation which are uncommon to most copper smelters: (I) The high grade of concentrate treated; this has always been about 50 pct copper. (2) The high flux burden on the charge. This is necessary because of the deficiency of bases in the concentrate and the high alumina content of the concentrate. (3) The frequent necessity of adding coal to the furnace charge to control the matte grade. (4) The high grade of matte produced. This has led to unusual converter problems. From the commencement of operations, the ore mined has come from the Roan Basin orebody. The concentrate produced from this ore consists mainly of chalcocite and shale with small proportions of other copper minerals. As mining operations extend to the Roan Extension orebody, the proportions of bornite and chalcopyrite in the concentrate will increase with a corresponding decrease in the copper content of the concentrate. Because of the concentrate grade the capacity of the reverberatory furnaces in terms of tons of copper produced per ton of coal burned is high. This ratio is usually over 2.2, and on especially favourable runs has reached 2.6. Reference to Table I shows that the iron content of the concentrate is unusually low. Only part of this iron is available for slag formation, the balance going to the matte. To make up this deficiency in bases, limerock is added to the furnace charge. This flux ensures a slag that is of the correct silicate degree, is suficiently fluid, of low specific gravity, and it counteracts the thickening effect of the alumina present. An ample supply of flux is obtainable from Ndola, 22 miles distant by rail. Although the reverberatory slag has a high copper content, the slag fall is low and the copper loss in the slag now rarely exceeds 1.0 pct of the total copper charged. The blister copper shipped is of such purity that only one fire refining operation has been necessary to produce a wirebar with properties comparable to electrolytic copper. Bismuth has always been the most troublesome impurity and consequently the problem of its control in the finished product has been of prime importance. Practically none is removed in the reverberatory furnace. The bulk of the elimina-

Jan 1, 1949

By Nathaniel Herz

The formula very frequently used for computing the economical size of pipe to transmit compressed air is that of D'Arey, as follows: D = cV w1l Where, D = the volume of compressed air delivered in cubic feet per minute, at the final pressure. c = an experimental coefficient determined for the various sizes of pipe, d = the diameter of the pipe in inches. 1 = the length of the pipe in feet. p, = the initial gauge-pressure in pounds per square inch, p2 = the final gauge-preesure in pounds per square inch. w1 = the density of the air, or the weight in pounds per cubic foot at the initial pressure, p1. The most common case is that in which the given quantities are: the quantity of air required, the length of the pipe, and the initial pressure. The method of solution is to assume a pressure-loss and to compute the remaining factor, cd5, thus giving the size of pipe corresponding to the assumed loss of pressure. It is always desirable to try two or more pressure-drops, in order to find the combination that is most satisfactory, since often a small change in the size of pipe will reduce or increase the loss of pressure several pounds. An alternative method is to assume a size of pipe and calculate the corresponding pressure-drop. Each method involves a series of tedious calculations to arrive at the most economical solution, and also requires the use of tables giving the constant, c, the density of the air, w1, and often, for convenience, a table giving the values of the expressions p1-p2 and c J I hare constructed a graphic chart, Fig. 1, for the solution of

Jan 1, 1913

By John L. Lamont, Walter Crafts

SELECTION of an alloy steel for a heat-treated article has been facilitated by methods for the calculation of hardenability,1 as-quenched hardness,2,3 and tempered tensile strength.4 Ductility and toughness may also be estimated if the steel is completely hardened on quenching,5,6 and the present study was carried out in order to develop a basis for estimating the Izod impact strength of partially hardened steel. The investigation was directed toward the prediction of Izod impact strength in steels of normal commercial quality without consideration of special compositions or heat-treatments that might produce abnormal brittleness. It was found that Izod impact strength of alloy steel is controlled by hardness, degree of hardening on quenching, and grain size. In fine-grained steels the impact strength for any given degree of hardening is inversely proportional to the tempered Rockwell C hardness, and the relation of impact strength to hardness is lowered by incomplete hardening. Calculation of the tensile strength and impact strength of heat-treating steels has shown that, except at very high strengths, tensile strength is raised by alloys without loss of impact strength whereas the tensile strength gained by higher carbon contents tends to be accompanied by a disproportionate loss of toughness. Plain carbon steels give relatively low and unpredictable impact strength. The calculation is sufficiently accurate to be helpful in the selection of alloy steel, and common grades of alloy steel have been evaluated with respect to combinations of tensile strength and impact strength attainable after heat-treatment in sections from I to 4 in. in diameter. PROCEDURE The study of the relation of hardness to impact strength was based on test data derived from 24 heats from four producers. The steels included the following SAE and AISI compositions: 1020, 1o30, 1040, 1340, 3310, 3316, 4320, 4330, 4340, 8620, 8630, 8640, 8720, 8730, 8740, 9310, 9317, 9440, 9917 and three high-alloy chromium-nickel-molybdenum steels. As far as is known, the steels tested were of normal commercial quality. They were supplied in 4-in. sections, which were forged to smaller sizes, prenormalized, and machined to final dimensions. Heat-treatment was carried out by heating to the usual austenitizing temperature for the grade of steel, holding for one hour per inch of thickness and quenching in still oil at room temperature. Previous work had indicated that this quenching treatment approximates a severity of H = 0.35. The bars were tempered as follows: ½ in., I in., and I 5/8 in., 2 hr; 2 ½ in., 3 hr; 4 in., 5 hr. All bars were air-cooled from the tempering tem-

Jan 1, 1947

GENTLEMEN : Herewith are submitted reports for the calendar year 1933 of your Treasurer and the Chairmen of the following standing committees: Finance, Admissions, Membership, Papers and Publications, Library, and MINING AND METALLURGY. TO these reports you are referred for additional details of the year's activity. Finances.-Income for 1933 from all sources totaled $121,690 com- pared with $138,331 in 1932. Incidentally, this exceeded the income as estimated in the budget by $7,190; the largest item being a "surplus" of $3,316 over the budget expectancy as to member dues. As compared with 1932 the most important items of shrinkage in income were $9,000 from dues and initiation fees; $5,500 from the magazine, MINING AND METALLURGY; and $2,500 from sales of publications other than the magazine.

Jan 1, 1934

By H. R. Wuthrich

The Metallgesellschaft AG decided in late 1965 to build an Electrolytic Zinc Plant at Datteln (W. Germany). Lurgi-Chemie was entrusted with the engineering and erection of the entire plant. Ground was broken in February 1967 and the operation was started on August 1st, 1968. The new Electrolytic Zinc Plant was designed to produce a minimum of 100,000 metric tons of special high grade zinc and 200,000 metric tons of sulphuric acid. Concentrates from Meggen (W. Germany) and mainly Timmins (Canada) are roasted in two turbulent layer roasters. The sulfur dioxide containing gases are converted in a "Bayer double catalysis unit" to sulfuric acid. The calcine is leached batch wise, the leach residue separated from the pregnant solution by counter-current thickeners and drum filters. For maintaining the sulfate balance a modified jarosite leach is being used. After a two step purification the neutral solution is mixed with spent electrolyte and cooled in unpacked atmospheric cooling towers. Three electrical circuits are supplying the power to the tankhouse, each rated at 30,000 amperes. With a maximum current density of 750 amperes per square meter and a stripping cycle of 24 hours, an average current efficiency of 90 percent is obtained. Cathodes are melted in one induction furnace and cast into shapes, or alloyed with aluminum and copper for die-cast metal.

Jan 1, 1970

By H. W. C. Prommel

While Utah remains an unimportant factor in oil production, exploratory drilling was carried on in six widely separated areas, extending from the southwest to the northeast corner of the state. One new gas field, the Last Chance or Starvation Creek anticline in Emery County, and two new gas horizons in the Clay Basin field of Daggett County, were thereby discovered during 1934. Exploratory Drilling South Central Utah Emery County—Last Chance Anticline.—The test of the Ramsey Petroleum Corporation in sec. 18, T.26S., R.7E., on the apex of this anticline (vert. closure 700 ft.; area within closing contour line, as mapped by U.S. Geological Survey, 26,000 acres) encountered gas in the Moenkopi formation of lower Triassic age at depths ranging from 2530 to 2863 ft. The total thickness of sandstone, sandy shale and -limestone beds in which gas was encountered is approximately 50 ft. The well was tested at a depth of 2755 ft., gaging 21,000,000 cu. ft. of gas, R.P. 410 lb. The well is being plugged back to the lowest gas horizon at 2771 ft. from a total depth of 3168 ft. Gas from this well probably will be used for the drilling of a second well structurally lower, to test the oil possibilities of the Moenkopi formation as well as of the upper and lower Pennsylvania formations, of which the latter so far remains untested in South Central Utah. The well was not drilled deep enough to determine more definitely the western margin of the petroliferous Paradox Basin of lower Pennsyl-vanian age of southeastern Utah. Woodside Anticline.—This field, lying immediately northeast of the San Rafael swell, contains, according to maps of the U.S. Geological Survey, 8380 acres within its lowest closing contour line 700 ft. below the apex. A well was drilled by Utah Oil Refining Co. at the apex in sec. 12, T.l9S., R.l3E., during 1924. Gas was encountered in the Moenkopi and Kaibab formations of Triassic and Carboniferous (Permian) age respectively. The flow is estimated at 21,000,000 cu. ft., R.P. 900 lb.,

Jan 1, 1935

By J. R. Martson

The arrangement of the larger furnace at the United Verde smelter, together with the boiler layout and connecting flues, is shown in Fig. 1. The important dimensions are given in the figure, and cross-sectional areas of combustion space, flues, etc., are recorded. The location and extent of the baffling in the boilers also are shown because of their importance in the interpretation of the data. Two boilers serve each reverberatory furnace. They are of the class M-26 Stirling type (rated at 713 boiler hp. each). Steam is generated at 178-lb. gage pressure at a total temperature of 528" F., from feed water at a temperature of 113" F. The feed water is condensate from turbogenerators plus make-up softened by the lime-soda process. The make-up is rather large in amount as it must match the amount of steam consumed in reciprocating blowing engines and the like, which are not served by surface condensers. As a result the boiler feed water has a hardness of 1.5 to 3.0 grains per gallon, but this results in the formation, during six months to one year of boiler operation, of scale only of "eggshell " thickness or less. The boilers are set at the same elevation as the tapping floor of the furnace, which results in the introduction of the waste-heat gases at the top of the front bank of tubes and necessitates the inversion of the usual baffling arrangements. The boilers are equipped with valve-in-the-head soot blowers, which keep most of the dust blown off the surface of the tubes, but it is necessary to supplement the soot blowers by high-pressure air lances, inserted by an attendant through side doors in the boiler setting. Deposits of coal ash and of dust from the furnace charge accumulate in the flues between the reverberatory furnaces and the boilers and this necessitates cleaning of these connecting flues by hand during the greater part of one of the three 8-hr. shifts during each 24 hr. This cleaning operation requires the opening of clean-out doors, which, of course, has some effect on the yield of steam. Revebberatory Furnace Practice The United Verde furnaces are fired with pulverized coal of sub-bituminous type of which the screen and chemical analyses are given in Table 1.

Jan 1, 1934

By S. J. Rothman, L. T. Lloyd

S. J. Rothman and L. T. Lloyd (Argonne National Laboratory)— Hagel's paperz0 discusses the question of the mechanism for self-diffusion in bcc transition metals. Recent work21"23 has led us to agree with him in reabandoning the ring mechanism in favor of a defect mechanism, most likely vacancies. On the other hand, we think that Hagel's attempt to group together all self-diffusion in bcc transition metals is wrong. We prefer the scheme of Peart, Graham, and omlin," who separate them into two groups. One group contains the anomalously behaved metals P titanium,', y uranium, and perhaps zirconim.' The other group contains a iron," this alloy was held at 1800°C for 2 hr before quenching, its structure was all a. B. C. Giessen, I. Rump, and N. J. Grant (Authors' reply)—We very much appreciate the discussion by Deardorff and Kato regarding the a to /3 transformation temperature of hafnium. In the W-Hf program, as well as in a current study of the system Cr-Hf, standard precautions were exercised against contamination, including vacua of less than 10"5 mm Hg and a weight control check of all specimens to insure an impurity rise of less than 100 ppm. Following receipt of the above discussion, a revision was made in the annealing process. Arc-cast specimens were etched with a 10 pct HF-90 pct HNO solution until 1 mm of surface, including a possible oxide film, was removed. Annealing was done in a hafnium container which provided a long diffusion path for gaseous contaminants. Finally, the heat treating time was shortened. Structural changes were noted to occur quite slowly. A 99.5 at. pct Hf alloy showed 70 pct /3 after 30 min at 1700°C and was 100 pct /3 after 10 min at 1715°C. After 24 hr at 1740C, the alloy was found to be 10 pct/3. This change is due to contamination; it was estimated that it corresponds to an increase of 60°C in the transformation temperature over a 24 hr period. The corresponding change in 30 rnin would be slight. Using the same hafnium as in the above publication, and three new alloys at 98, 99, and 99.5 at. pct Hf, the transformation temperature was indicated to be 1715" 15°C. Since this hafnium contained 4.4 at. pct Zr, a correction of 40 5C, based on an assumed approximately linear transformation temperature curve, must be made for pure hafnium. This yields a value of 1755 20°C in good agreement with Deardorff and Kato's value. Because the slope of the boundary is small, this permits a good extrapolation, and we regard the W-Hf alloys as well suited to check the Hf transformation temperature. niobirn,'' and molybdenum,22 whose activation energies correlate with the melting temperature and whose Do values follow Zener's predictions.28 We have no quarrel with Hagel's placing chromium into the second group; we disagree with his interpreting our data to make uranium fit into that group. Hagel considers that the measurements of self-diffusion in uranium below about 950°C represent combined volume and grain boundary diffusion. This contention is based on the curvature of the penetration plot for our 891°C run,4 which also has a nearly straight line plot of log c vs x. Hagel has extrapolated these characteristics to our 803.5C run and fitted his Arrhenius plot for self-diffusion in y uranium to our four highest temperature points only. We think this is wrong for the following reasons.

Jan 1, 1963

By H. David Swain

On Bougainville Island in Papua New Guinea, Bougainville Copper Ltd. (BCL) has successfully applied electronic data processing (EDP) techniques to pit operations and mine planning. Though the EDP program is not complete, BCL has realized significant improvements in short and long range mine planning, and equipment and manpower utilization. About 80% of BCL's 4000 employees are Papua New Guinea nationals, and most have little education or training. The operational characteristics of the computer equipment, however, have been quickly adapted by users with low educational standards.

Jan 3, 1979

By C. J. Osborn

In oral discussion at the Columbus midyear meeting, September 26, 1949, these pertinent questions were asked: Was a satisfactory separation of metal and matte obtained? The matte was quite fluid and in most cases the separation was satisfactory. Were the mattes chlorinated after aging? The mattes were stored in sealed glass mason jars, and chlorina-tion experiments made after standing for several weeks gave satisfactory results. Was ferric chloride volatilized? Most of the iron content of the matte was converted to ferric chloride. However, because of the low chlorination temperatures used (150" to 250°C) the major part of the ferric chloride remained with the residue. Undoubtedly, some ferrous chloride was also formed, because of the reducing conditions within the reaction vessel, but no effort was made to separate it from the ferric chloride. Could the reaction be stopped before making metallic iron? No attempt was ever made to stop the reaction before making metallic iron. Generally, 20 to 60 pct of the iron in the charge was obtained as metallic iron which could be readily separated from the matte. In certain cases, metallic iron was dispersed through the matte in the form of globules, which could be removed by magnetic separation. Could other sulphides, i.e., calcium sulphide or sodium sulphide be used in place of iron sulphide? No other sulphides were investigated. It was felt that titanates of calcium and sodium would be formed should these sulphides be used to replace the pyrite. What were the sulphur volatilization losses during matte smelting? In the course of this laboratory investigation, a rather wide variety of variables was introduced from highly oxidizing to reducing conditions and various ratios of pyrite, rutile, and coke. These and other factors all have a definite bearing on the sulphur losses. In general, the higher the sulphur in the charge the higher were the sulphur losses and the percentage of titanium in the matte decreased. With sulphur additions more nearly the theoretical amount, the sulphur losses averaged approximately 10 to 15 pct. With a higher percentage of sulphur on the charges, the losses were in the order of 15 to 30 pct.

Jan 1, 1951

By C. C. Herrick

The vapor pressure of indium has been measured by the torque-effusion technique, as a function of temperature between 1102o and 1422oK. For liquid indium, the vapor pressure (in atmospheres) can be represented by the equation -R In P = 5.782 x104/T - 25.29from 1000o to 1422oK. Extrapolation yields a calculated normal boiling point of 2329°K and a heat of vaporization at 298 oK of 58.09 kcal per mole by the third-law method and of 58.39 kcal per mole by the second-law method. Calculations indicate that the free-energy functions of Hultgren are to be preferred to those of Guruich. BECAUSE of the potential uses of liquid metals, it is important that convenient experimental methods be developed which will lead to a sufficient body of thermodynamic data so that reasonable estimates of properties of liquid metals can be made. Indium is particularly well-suited to investigation, since it remains liquid over a long temperature interval, it alloys readily, suitable containers for it are easily procured, and relatively few investigations of its thermodynamic properties in the region above 1000°K have been made. PREVIOUS RESEARCH The first determination of the vapor pressure of indium was made by Anderson,' using the Knudsen method and silica-lines stainless-steel cells. Kohlmeyer and spandau2 determined the normal boiling point, and a mass-spectroscopic investigation has been made by Lyubimov and Lyubitov.3 (Unfortunately, only an equation representing the data of the latter investigators has been available to us.) Hultgren et al.4 and Gurvich5 have published discordant tables of the free-energy functions for indium. EXPERIMENTAL METHOD The torsion-effusion principle has been described amply in the literature.8,7 With this method, one observes the angular deflection induced by effusion of vapor from a multihole effusion cell which is suspended from a filament producing a small rotational restoring force. The pressure within the effusion cell can be computed from the relation ziaifiai where k is the torsion constant of the filament, 6 is the observed angular deflection, and ai, fi, and qi are the area, force factor, and moment arm of the ith effusion orifice. The force factor f is analogous to the Clausing factor,' and corrects for the reduction in effusive force attributable to the finite geometry of the effusion orifice. Schultz and Searcy' have tabulated the force factors for various tube geometries. EXPERIMENTAL APPARATUS The physical arrangement employed in this study is shown in Fig. 1. The furnace elements are six Globar heat rods with 15-in. hot zones. Temperature is maintained to * 1°K by a Beck mechanism driving two 26-amp Powerstats in parallel. A Pt (Pt, Rh 10 pct) thermocouple serves as the sensing element. Four inner tubes act as vibration isolators; the air pressure required for maximum isolation was determined empirically, and is maintained by a solenoid valve. The tungsten fiber, 9 by 0.002 in., is joined to an 0.008-in. tungsten wire or graphite rod via a machined lightweight chuck.

Jan 1, 1964

By Paul M. Tyler

ROUGHLY one-half the value of mineral products at mines or quarries must be spent for wages. In view of the steady increase in hourly wages that continued for several decades prior to the onslaught of the recent depression, it is perhaps surprising to discover that labor's share of the gross proceeds of the mining and quarrying industries of the United States declined to 46.8 per cent in 1929, compared with 52.2 per cent in 1919 and 53.2 per cent in 1909. The actual percentages vary in different branches of the industry and in different localities but the downward trend is unmistakable. For the period 1909 to 1919 it was quite marked in every industry and from 1919 to 1929 it was apparent in all but six: namely, gold and silver lode mining, placer gold mining, crude gypsum production, marble quarrying, asbestos production, and fluorspar Tninino mining

Jan 1, 1933

I HAVE now traversed for you in the small and fragile bark of my writing all the shores of the deep and spacious sea embracing the uses of material fires, drawn on by my own desire to enrich you with more learning and with the procedures of these things, as much as to satisfy your demands. Having through the grace of God arrived at the appointed end of my voyage and neither knowing nor perceiving a way of going farther, I had decided to furl the [167] sails and cast die heavy anchors into the water in order to enjoy in tranquillity respite from my sailing, when I was warned by my pilot that before I could disembark I should turn my glance backward and reexamine my work in detail to see if there were any part that had by chance remained undescribed in the obscurity of silence. When I did this there immediately appeared in my mind's eye the many sublimates and smoky tinctures that had been made by the burning and most powerful fire of love. I need not say that I knew of it in far-off countries or from the knowledge of others, but I knew it in my own breast and as my very own and can therefore surely esteem it as hotter than all the other fires that the world calls by that name. Although today its sparks and living flames are spent because of my cold and hoary season, nevertheless it is true that the memory of acts of love of long ago still remains with some smoke and warmth. Therefore, since in this work of mine I wish to describe for you the effects and powers of fires, I should logically have spoken of this before any of the others, because of its actual nearness and the great acquaintance I had with it. But since I have had the glance of my intentions directed at distant things, I have behaved as one does who does not see where he places his feet because he is looking at the sky, or as one who thinks about the affairs of others and forgets his own. But now I do not wish to pass over this thing and I wish to correct my error, particularly in order to provide a happier ending to my written work than by remaining among the horrible uproar of guns, powder, and saltpeter, which would be a harsher ending than speaking of love. Never-

Jan 1, 1942

J. H. HEGINBOTHAM, a, metallurgist of the General Engineering Co., talked on "Current Milling Practice at Kirkland Lake," at the December meeting of the Utah Section. The ore is enough alike through the whole district so that some generalizations and comparisons may be made. The question as to whether or not the flotation process should be used in the flowsheet for extracting gold by cyanide solutions is still being vigorously debated, and it will seemingly need some years for a definite answer to be given. Most of the gold is either free, though much of it is finely dispersed in quartz, or occurs with pyrite. At times there may be 2 per cent of telluride compounds in the ore, but the amount of gold telluride present is small and has not been definitely established. It has been shown by Dr. Haultain and others that though gold tellurides may be so finely disseminated that it is necessary to grind the ore exceedingly fine, the compounds themselves are not difficultly soluble. (An increase in temperature helps to dissolve tellurides, and also to settle pulps.) It is likely that if the ore were ground through 400 mesh, practically all of the gold would be soluble. As it is, with 96 to 98 per cent of the ore ground to minus 200 mesh, and some 70 per cent minus 325, the cost of

Jan 1, 1934