Search Documents

Jan 1, 1915

By F. V. Lenel, J. A. Dromsky

The influence of thermal and mechanical treatments upon the elevated-temperature stability, the microstructure, and the mechanical properties of aluminumaluminum oxide alloys is investigated. Compacts from atomized and flake aluminum powders were sintered at temperatures just below the melting point of aluminum in a vacuum of 10-4 Torr for several hours and were then hot-extruded. During this treatment the hydrated oxide present on the surface of the powder particles decomposes, the water vapor produced reacts with the aluminum forming additional oxide, and the hydrogen developed is removed by diffusion to the surface. Extrusions of compacts so treated are stable at temperatures up to the melting point of aluminum and do not form blisters and internal defects typical of extrusions from untreated powder. Electron micrographs of extrusions from unsintered compacts show long parallel oriented platelets typical of the IN previous investigations1,2 the properties and structure of aluminum alloys were described which had been produced by cold compacting aluminum powder and then hot pressing and extruding the compacts. Both the structure and the properties of these alloys differ significantly from those of commercially produced aluminum-aluminum oxide alloys. When commercial alloys are produced, they are given a sintering treatment in air at about 600°C between cold compacting and hot pressing.3 During this treatment the hydrated oxide, which forms the coating on the aluminum-powder particles from which the alloys are prepared, is decomposed.4 The chemically bound water which is released reacts with the aluminum and forms aluminum oxide and hydrogen. Most of the hydrogen is eliminated by hydrated oxide skins on the original powder particles, while the oxide particles in extrusions from sintered compacts are broken up. The strength of extrusions from treated powder is somewhat lower, but their ductility is considerably improved over that of extrusions from untreated powder. The slip-trace patterns on electron microgvaphs of extrusions which had been strained in tension before replication indicated that the grain size of the extruded alloys was approximately the same as that of the original powder particles. Coarse-grained alloys were produced by severe cold work and annealing of the extrusions. They have significantly lower room-temperature strength, but about the same ductility as the vacuum-sintered fine-grained alloys. The size and shape of oxides in the coarsegrained alloys is similar to those of the fine-grained alloys, but the particles are somewhat more uniformly distributed. diffusing to the interior or exterior surfaces of the compact, but it is difficult to eliminate all of it because the solubility of hydrogen in solid aluminum is very low even near its melting point. Extruded alloys which are not sintered before hot pressing and extrusion appear quite sound upon metallo-graphic examination, but develop severe surface blistering and internal fissuring when they are heated to elevated temperatures after extrusion. Fissures and blisters have been observed even in commercial alloys which had been sintered in air, although they are much less severe.' Because of the importance of this sintering treatment it was studied in this investigation in a modified form, using vacuum sintering rather than sintering in air, to insure more complete elimination of occluded hydrogen. The technique is described and the effect of the treatment upon the structure of the alloys is documented. It has been known for some time that extruded aluminum-aluminum oxide alloys are very finegrained, but an exact delineation of grains in electron micrographs has not been possible. In the conventional metallographic-etching techniques etchants attack the interface between the second-phase particles and the matrix in the alloys much

Jan 1, 1964

By Oliver Bowles

DIMENSION stone is a convenient term applied to stone sold in blocks or slabs of specified shapes and usually of specified sizes, as contrasted with crushed, broken and pulverized stone, discussed in another chapter. Dimension stone includes cut stone, rough building stone, ashlar, rubble, paving blocks, curbing and flagging. Riprap-large, irregular blocks used for shore protection-is classed more properly with crushed and broken stone. COMPOSITION, VARIETIES AND PROPERTIES Stones used as blocks or slabs are of many kinds. The principal varieties are granite, sandstone, limestone and marble. Slate is covered in another chapter. Granite is a visibly granular crystalline rock consisting essentially of feldspar, quartz, and mica or hornblende. Limestone consists essentially of calcium carbonate, with which may be associated certain impurities such as clay, sand, or iron oxide. Dolomites and magnesium limestones used as dimension stone are classed with the high- calcium limestones, as they are used in the same way. Marble is a crystalline form of limestone. Sandstone consists essentially of silica in the form of sand grains cemented together into a coherent mass. Although rock occurrences are numerous and widespread, the ex- acting requirements of use condemn all but a small fraction of them for commercial use as dimension stone. No deposit that has closely spaced cracks, lines of weakness, or joints can be so used because sound blocks of moderate to large size are demanded. Uniform texture and grain size, constant and attractive color, and freedom from impurities that may cause stains or deterioration usually are required also. Hardness is a variable property. Granites are as hard as or harder than steel while limestones and marbles may be scratched easily with a knife. The hardness of a sandstone depends upon the degree of cementation of the grains. Workability depends to a considerable extent on hardness, but the degree of hardness has little influence on use except when stones are subjected to severe abrasion, as on steps or floors. "Texture" as applied to stone relates to the arrangement, uniformity, and size of the constituent grains.

Jan 1, 1949

By Wilbur I. Duvall, Thomas C. Atchison

Over the past ten years a series of investigations have been conducted to determine some of the physical processes involved in breaking rock with confined concentrated charges. Detailed discussions of many of these investigations have been published elsewhere.1-6 Laboratory experiments made by other investigators using Hopkinson pressure-bar techniques have shown that solid materials are fractured in tension by the reflection of an incident compressive stress pulse at a free surface.7-12 In these tests a small charge of explosive is placed in contact with one end of a bar. Detonation produces some plastic flow and crushing of the bar near the charge and generates a compressive stress pulse that travels along the length of the bar. At the free end of the bar the compressive stress pulse is reflected back into the bar as a tensile stress pulse. If the tensile strength of the bar is exceeded during this reflection process, a tensile fracture normal to the length of the bar is produced, and the broken end of the bar moves forward with a constant velocity equal to the average particle velocity trapped in the broken fragment. The new surface formed by the fracture becomes the new free end of the bar that reflects the remaining portion of the incident compressive stress pulse. This process is repeated any number of times until all of the incident stress pulse is reflected.

Jan 6, 1959

Jan 1, 1885

By AIME AIME

THE following brief description of the main features of the, engineering work was prepared for the use of members of the American Society of Civil Engineers and members of the American Institute of Mining Engineers on the occasion of their visits to the tunnels at the time-of their respective. annual meetings in New York, January and February, 1905. DESCRIPTION. Those portions. of the Pennsylvania Extension into Manhattan and Long Island, lying east of the Terminal Station and west of the East River, have been designated as the " Manhattan ?Cross-town:. Tunnels." They traverse a section of the city second in importance only to the financial district, and one that includes the larger hotels, retail shops and theaters and the residences of many of the best known citizens. Section "D," consisting of twin tunnels for west-bound express and local passenger traffic, lies under Thirty-third Street from a point 400 ft. west of the west line of Sixth Avenue, eastward to the river shaft, situated in the block between Thirty-third and Thirty-fourth Streets east of First Avenue. Beginning at the east end, the tunnels are in separate excavations, leading westward from the subaqueous tubes, on a curve of large radius, gradually closing together until it is found more appropriate to drive them in a single excavation. At a point just west of Second Avenue they reach the tangent, aid from there westward lie directly under Thirty-third Street. At a point about 180 ft. west of the west line of Sixth Avenue, the center concrete-wall between the twin tunnels is omitted, and the excavation somewhat widened to make room for a third storage-track, and the tunnel continues to tile station portal in three-track section. Here reprinted through the courtesy of The United Engineering and Contracting Co. The half-tone blocks used for the illustration of this paper have been kindly supplied by the Chasmer-Winchell Press of New York, Pittsburgh and Cleveland.

Mar 1, 1908

Jan 1, 1906

By R. T. DeHoff, L. J. Buteau, J. Kronsbein

Network topology is introduced and used to describe sinter bodies at various stages of the sintering process. The matrices of incidence, loop-branch. tree-branch, and cut-branch are constructed and their relationship to the three-dimensional void space and the common two-dimensional bounding surface is established. The sintering body is assunzed to remain connected but this is not so with the void space. The topological invariants known as Betti numbers are related to this observed fact and provide parameters which measure the progress of the sintering process. They are extracted from the matrices by means of known algebraic operations. Experimental procedures are given which permit actual construction of the various matrices and determination of the Betti numbers by serial sectioning of the sinter bodies. A sinter body is produced by exposing a large number of metallic particles (0.00001 to 0.3 in. diam) to a temperature that is near but below their melting point. When these particles are maintained at such a temperature for a sufficient length of time, it is found that the interparticle contacts become welded. As time increases, these welds, often referred to as necks, grow. All of the space between the particles constitutes a single connected void; an ultimate consequence of sintering is the breaking up of the void into separated parts. A mathematical apparatus for describing the geometric characteristics of a sinter body at each stage of the process was first proposed by F. N. Rhinesl when he introduced the application of topology to this problem. He described the sinter body in terms of one of its topological invariants, the genus. The most important advantage of a topological description is invariance with respect to continuous deformations. This means that particle sizes and shapes need not be considered, resulting in considerable simplification and generalization of the geometric description. In the case of a sinter body, wherein the internal geometry is particularly complex, the simplification provided by topological concepts is absolutely essential. The important parameters in the Rhines model are the number of particles and the interparticle contacts. The invariant considered called genus is given by Euler's formula for the connectivity of two-dimensional surface of the sinter body. This surface includes the pore-solid interface. The Euler formula is G = C - P + 1 [1] where C = number of interparticle contacts, P = number of particles, and G = genus of the surface bounding the sinter body. In topology the term genus may be used to mean the number of self re-entrant cuts that can be made on a closed surface without dissecting it into more than one connected surface. Its use is restricted to the surface and does not apply to the three-dimensional volume enclosed or excluded by it. In the case of sintering, the volume enclosed by the surface is defined as the sinter body; the volume excluded will be referred to as the void space. There is an intrinsic reason for using genus as a characteristic number associated with a sinter body. The genus is related to the Gaussian curvature by the integral of the product of the principal curvatures taken over the entire surface of the sinter body, as given by

Jan 1, 1965

By G. A. Mancini, V. Bharucha, J. W. Spretnak, G. W. Powell

The characteristics of the motion of the a interface during the "down" transformation was studied in zone-refined iron and dilute binary alloys containing nickel and molybdenum by means of the thermionic emission microscope and high speed photography. The frontal movements were found in all cases to be definitely discontinuous with time and an appreciable number of incremental jumps were found to proceed in the reverse direction (a to b). Molybdenum was found to be particularly effective in increasing the frequency of the increments of transformation from the stable to the metastable phase. A knowledge of the mechanism by which alloying elements affect the hardenability of a steel is desirable from both the practical and scientific viewpoints. It is well established that microstructures consisting of tempered martensite and lower bainite exhibit the best performance in terms of toughness and resistance to crack propagation. The presence of some upper transformation products, namely ferrite and pearlite, is in general undesirable. Various researches have indicated that the ferrite matrix grain structure is a very important difference between the upper and lower transformation products, namely equi-axed vs acicular. Any comprehensive theory of the decomposition of austenite should explain the dependency of the morphology of the matrix on undercooling. The contribution of various alloying elements to hardenability has been determined experimentally and catalogued in considerable detail. A rationalization of the basic mechanism or mechanisms by which individual elements affect the kinetics of the decomposition of austenite to products other than the phase "martensite" has not been evolved as yet. Interest in this problem was stimulated by the effects of minute quantities of boron in hardenable steels. This paper deals with one aspect of this problem, namely the characteristics of the ?-a transformation in high-purity iron and in two carbon-free iron binary alloys. A detailed historical account of the scientific developments in the study of the decomposition of austenite would be a prodigious undertaking and will not be attempted here. There are several excellent reviews in the literature on the formation of pearlite, martensitic reactions, and kinetics of solid-state reactions. The thinking on reaction mechanisms has been influenced to a large degree by the "classical" Tammann nucleation and growth model, in which an embryo springs into being by a fluctuation, and grows to a critical size through atom by atom deposition. Such a process is expected, accordingly, to be diffusion controlled. Considerable research attempting to relate the contribution of alloying elements to hardenability on the basis of their effect on the diffusivity of carbon in iron has not been productive from a mechanistic viewpoint. The formation of pearlite and ferrite has been treated in terms of nucleation and growth processes in which presumably the lattice transformation also occurs by a diffusion process. The other prominently considered mechanism is the "martensitic" or cooperative shearing mechanism. It seems generally, but not entirely, agreed that the phase "martensite" forms by this mechanism, and that it is involved to some extent in

Jan 1, 1962

By Shawn T. Sorrell, Carl Hrovatic

Land is a precious resource and should be treated as such by all members of our society. The soil covering this earth is only a very thin outer layer, varying in thickness from a few inches to a few feet and covering the rocks and minerals lying beneath the surface. The wise use of this valuable commodity is the responsibility of everyone. Many everyday activities disturb the earth's surface. Examples are highway construction, housing and commercial developments, agriculture, and surface mining. This chapter discusses the relationships of the environment to land as it applies to surface operations ill the coal industry. Mining by surface methods disturbs, for a brief period of time, thousands of acres of land annually. In addition, refuse piles, slurry ponds. abandoned mine structures, unprotected mine openings, and unsightly cleaning plants can also adversely affect land unless properly handled. ACTIVE SURFACE MINING OPERATIONS Mining by surface methods includes rock quarries; sand and gravel pits; huge open pits to extract iron, copper, phosphate, and other ores: and coal mining. Production of coal by surface methods is now approaching 300 million tons annually, amounting to almost 50% of the total coal output. Surface coal mining can be classified into the following four broad categories: Open pit mining is practised where the coal beds are extremely thick, as in some western states, or where the coal beds are sharply pitching, as in the anthracite region of the eastern United States. A typical open pit mine, with coal beds of 10 to 100 ft or more thickness and a relatively small ratio of overburden, generally employs large scraper-loaders to re-

Jan 1, 1973

By Frederic Benard

The electrolytic copper refinery at Copper Cliff, Ont., is operated by the Ontario Refining Co., Ltd. The associated companies behind the enterprise are the International Nickel Co. of Canada, Ltd.; The American Metal Co.; The Consolidated Mining & Smelting Co. of Canada, Ltd.; and Ventures, Ltd. The plant was the outgrowth of the rapid development of copper resources in the nickel-copper ores of the Frood and other great mines in the Sudbury district, and of the desire to have all primary production units grouped together as closely as possible. The refinery is near the intersection of the Sault Ste. Marie to Sudbury highway and the Canadian Pacific Railway. It is about one mile south of The International Nickel Company's smelter at Copper Cliff. The standard-gage track systems of the refinery and of the smelter are connected by a standard-gage timber railroad trestle that crosses the railway and the highway by means of steel girder spans. The Canadian National Railway has access to the plant by means of this trestle and the nickel company's tracks, so that the refinery has connections with both the Canadian Pacific and the Canadian National railways, as well as a direct connection with The International Nickel Company's smelter, from which the bulk of the copper to be refined is hauled by the latter's electric locomotives. Buildings The refinery (Fig. 1) covers approximately 60 acres, enclosed by an unscalable chain-link fence. The main buildings have a content of 23,000,000 cu. ft., with a total roof area of approximately 600,000 sq. ft. and near them are the substation, cooling pond and main standard-gage track system (Fig. 2). A ladder track for car storage extends 1200 ft. south of the coal-pulverizer tracks and the scale house is on this spur. The intake and pumphouse for fresh water supply are at Kelly Lake, about 3000 ft. south of the plant. Owing to the severity of the winters, when temperatures of from 20" to 40' below zero are to be expected, the building of this refinery involved a number of problems in insulation, layout, ventilation, etc., which were

Jan 1, 1934

By H. E. Swanson

A description of the field apparatus has been published by D. G. Brubaker. Data from laboratory model studies of the in-line and broadside methods of operation are detailed. The conductor models include a single sheet conductor at several strike and dip angles and a schistose-type conductor. In addition, data on the effects of the strike length and of the depth of the conductor are presented for the broadside method of operation. All of the data show that the inclintion reverses direction over the top edge of dipping single sheet conductors. Differences between anomalies over conductors dipping between 90" and 30" are subtle,but flat-lying sheets can be readily distinguished from steeply dipping sheets. Schistose conductors are easily distinguished from single sheet conductors, and a procedure is given for determing the direction of schistosity. The depth of penetration under ideal conditions is 0.7 of the coil separation. In 1950, The New Jersey Zinc Co. (of Pa.) developed a lightweight apparatus for electromagnetic prospecting. A description of this apparatus has been published by D. G. Brubaker.1 It consists of a small, battery-powered vertical source coil and a direction-finding receiving coil. Source and receiver are kept a fixed distance apart and move as a unit along the survey lines. At each receiver station the inclination of the magnetic field created by the source is measured. Two methods of operation are used, in each of which measurements are taken with a constant source-to-receiver distance and with the plane of the source oriented to pass through the receiver station. In one procedure, called the in-line method, source and receiver travel in tandem along the same line. In the other procedure, called the broadside method, source and receiver move along adjacent lines, with the source-to-receiver direction oriented parallel to the assumed strike direction. The data recorded in either case are the inclinations, measured in degrees from the horizontal, of the magnetic field created by the source. These data are plotted at the receiver stations on a map. Scale-model studies of both methods of operation have been conducted in the laboratory and are reported in this paper. APPARATUS Small source and receiving coils wound with many turns of fine copper wire were used to produce and measure an alternating magnetic field in the same manner as the field apparatus. The model source coil was mounted in a vertical position and oriented so that the receiving coil was in the plane of the source. The receiving coil was mounted in a frame so it could be rotated to obtain the inclination measurements. The source coil was excited by a 100-kc signal generator. A tuned amplifier and a voltmeter were used to detect the null position of the receiving coil. The coils used in the field apparatus are usually spaced about 400 ft. The coils used in the model work were spaced from 4 in. to 4 ft apart. Thus the scale of the model work ranges between 1/1200 to 1/100 natural size. The model conductors were aluminum-coated building paper supported on wooden frames. The conductivity-thickness product was measured using a four-electrode system and was found to be about 300 ohms-'. CONDUCTIVITY CONSIDERATIONS The electromagnetic response from a thin sheet conductor is a function of the product of the conductivity of the sheet times the thickness of the sheet times the frequency of the alternating electromagnetic field times some linear dimension of the system such as the coil separation which indicates scale. The secondary electromagnetic field produced by the conductor increases in amplitude from zero at zero conductivity to a maximum value for infinite conductivity, while the phase of the secondary field with respect to the primary field shifts from 90" at zero conductivity to 0" at infinite conductivity. Several authors2-' have shown that most of both the increase in amplitude and the change in phase of the secondary field takes place over a three-decade range of the conductivity-thickness-frequency product. Only small changes in the amplitude and

Jan 1, 1961

By D. G. Westlake, D. T. Peterson

The saturation solubility of thorium dihydride in thorium was studied by saturation of samples and subsequent analysis. The solubility increased from about 1 at. pct at 300°C to above 20 at. pct at 800 °C. Over this temperature range the log of the solubility was a linear function of the reciprocal absolute temperature for thorium of good purity. The heat of solution of thorium dihydride was found to be 7.9 kcal per atom of hydrogen in crystal bar thorium and 6.6 kcal per atom of hydrogen in Ames thorium, The important effect of hydrogen on the physical and mechanical properties of many metals is receiving increasing recognition. The basic physical and chemical data necessary to help explain the observed effects of hydrogen on the mechanical proper ties of metals are all too often not available. The solubility of hydrogen in thorium metal was determined to provide a portion of this basic data for the thorium-hydrogen system. The absorption of hydrogen by thorium metal and the formation of thorium hydrides was studied by several investigators, beginning in 1891, and their work is summarized in Gmelin's Handbuch.1 No effort was made to determine the extent of solid solubility in the metal in these early investigations and the impure metal available made interpretation of the results uncertain. Nottorf2 reported the results of a careful study of pressure-composition isotherms for the thorium-hydrogen system. The principal interest in this work was in the composition and dissociation pressures of the thorium hydrides. Mallett and campbel13 reported the pressure-composition isotherms for the thorium-hydrogen system up to the composition of thorium dihydride. The saturation solubility of thorium dihydride in thorium was reported to be 13 at. pct at 650°C and 23 at. pct at about 900° C. Mallett and Campbell used thorium metal which had been prepared by the calcium reduction of thorium tetra-fluoride or thorium oxide. The results obtained with thorium of these two types agreed within the experimental error. PROCEDURE AND MATERIALS Procedure—The method used to determine the solubility was to saturate a sample of thorium with hydrogen and analyze a portion of the saturated sample. This method was chosen rather than a determination of pressure-composition isotherms since it was much less time consuming and could be applied at temperatures at which the equilibrium hydrogen pressure was too low to measure. The

Jan 1, 1960

By A. W. Jenike

A theory of gravity flow of bulk solids like ores, concentrates, coal is outlined and an example of design for unobstructed flow is given. Mass-flow and plug-flow patterns are defined and related to the geometry of the bin. The effect of these patterns on segregation, first in-first out flow, and caking is described. This paper is a report on the results from the AIME sponsored project "Flow of Bulk Solids" which was carried out under the author's direction at the Utah Engineering Experiment Station, University of Utah, during the period 1956-1962. The theory has been applied to the design of numerous industrial storage plants. A QUANTITATIVE METHOD OF DESIGN FOR FLOW There is hardly an industry which does not store and handle solid materials in bulk form. When the volume of the solids is large, gravity is invariably relied upon to cause the solids to flow out of storage, through channels and chemical reactors. Such materials as ore, coal, cement, flour, plastics, clay, soil, to which a general term of bulk solids is applied, flow by gravity or are expected to flow by gravity in thousands of installations and by billions of tons annually. The chemical and process industry depends on gravity flow of solids in process and out of storage. Mining relies on gravity flow in block-caving, in ore passes, as well as in storage and loading bins. Agriculture uses gravity flow in elevators, in feed plants, and in farm silos. In practice, satisfactory gravity flow is seldom attained. Such problems as doming, piping (rat-holing), lack of live capacity, segregation, deterioration in storage, harass industry. In spite of the universality of these problems, until recently, there has been no theory of solids flow, no method of predicting how a solid would behave, and how the channel, bin, or hopper should be designed. In the late nineteen forties and early fifties, the theory of plasticity came of age and simultaneously the computer became widely available. These two factors permitted the development of a theory of flow of bulk solids. The work was conducted during the years 1953-1961. In conjunction with the development of the theory a method to measure the flowability of solids was also developed1-7 and the theory was ap-plied to the design of ore pockets, storage plants,16 chemical reactors and adsorption columns. A comprehensive report of this work is given in a previous work." THEORY OF FLOW The most important question which a theory of flow has to answer is: what conditions need to be satisfied for a given solid to flow uniformly and without obstructions through a channel? First of all, the following observations are made:

Jan 1, 1967

By J. R. Lewis, J. H. Hamilton, V. D. Hanson, K. W. Heinlein, J. M.194-000-000-006 Vonfeld, J. P. Denny

TWO overfeed drum-type separators using a suspension of magnetite in water as the separating medium have been installed in the Champion NO. 1 preparation plant of the Pittsburgh Coal Co., Division of the Pittsburgh Consolidation Coal Company. A simplified flow diagram of the Champion No. 1 coarse coal circuit is shown in Fig. 1. A railroad car rotary dump, capable of handling 20 cars per hr, discharges the coal into a hopper. Coal is fed from the hopper of the rotary dump to a 60-in. belt conveyor by two reciprocating pan-type feeders. The belt conveyor feeds the run of mine coal onto the main raw coal screen. The first deck is fitted with 3 in. round hole perforated plate which removes the 3x0-in. coal. The second deck of the screen is equipped with 6-in. lip screens which separate the remaining coal into +6 in. and 6x3 in. The +6 in. coal is transferred to a shaking picking table and then discharged onto the loading boom. The 6x3-in. coal is fed to the No. 2 dense medium vessel for cleaning. The clean coal from this unit flows to a vibrating screen where the medium is removed and the coal sized into 6x4 in. and 4x3 in. The 6x4-in. coal is transferred to the loading booms and the 4x3-in. is conveyed to the clean coal classifying screens to remove degradation. The 3x0-in. raw coal is blended in a system composed of three storage bins having a total capacity of 400 tons. From these bins the coal is fed onto a 48-in. flight conveyor by three reciprocating feeders. This flight conveyor delivers the coal to the Rheo plant. The 3x0-in. coal is then cleaned in two 48-in. Rheolaveur launders each equipped with two Rheo boxes. The first set of boxes removes a primary refuse and the second set produces a middling product which is recirculated in the launders. The cleaned coal and water overflows from the primary launders to two sizing and dewatering shaker screens where the water and — -in. coal are removed for further cleaning in the Rheo fine coal plant. The 3x3h-in. clean coal is combined with the 4x3-in. coal from the No. 2 vessel, sized into 4x2 in., 2x1 34 in., and 1'/4x in., then sent to the loading booms. The 3x0-in. refuse from the primary launders is normally fed to the No. 1 dense medium circuit, but any portion or all of this material can, as an alternate, be processed in the Rheo rewash launder. The primary refuse when fed to the dense medium circuit is screened into YSXO which is cleaned in the fine coal plant and 3x for cleaning in the No. 1 vessel. The clean coal from this vessel is passed over a vibrating drainage and rinse screen, then sluiced to the rewash sizing shaker where it is dewatered and sized for loading. The installation of a pilot plant separating vessel using a suspension of magnetite in water was pro-

Jan 1, 1953

By J. H. Hamilton, J. R. Lewis, K. W. Heinlein, V. D. Hanson, J. M. 194-000-000-006 Vonfeld, J. P. Denny

TWO overfeed drum-type separators using a suspension of magnetite in water as the separating medium have been installed in the Champion NO. 1 preparation plant of the Pittsburgh Coal Co., Division of the Pittsburgh Consolidation Coal Company. A simplified flow diagram of the Champion No. 1 coarse coal circuit is shown in Fig. 1. A railroad car rotary dump, capable of handling 20 cars per hr, discharges the coal into a hopper. Coal is fed from the hopper of the rotary dump to a 60-in. belt conveyor by two reciprocating pan-type feeders. The belt conveyor feeds the run of mine coal onto the main raw coal screen. The first deck is fitted with 3 in. round hole perforated plate which removes the 3x0-in. coal. The second deck of the screen is equipped with 6-in. lip screens which separate the remaining coal into +6 in. and 6x3 in. The +6 in. coal is transferred to a shaking picking table and then discharged onto the loading boom. The 6x3-in. coal is fed to the No. 2 dense medium vessel for cleaning. The clean coal from this unit flows to a vibrating screen where the medium is removed and the coal sized into 6x4 in. and 4x3 in. The 6x4-in. coal is transferred to the loading booms and the 4x3-in. is conveyed to the clean coal classifying screens to remove degradation. The 3x0-in. raw coal is blended in a system composed of three storage bins having a total capacity of 400 tons. From these bins the coal is fed onto a 48-in. flight conveyor by three reciprocating feeders. This flight conveyor delivers the coal to the Rheo plant. The 3x0-in. coal is then cleaned in two 48-in. Rheolaveur launders each equipped with two Rheo boxes. The first set of boxes removes a primary refuse and the second set produces a middling product which is recirculated in the launders. The cleaned coal and water overflows from the primary launders to two sizing and dewatering shaker screens where the water and — -in. coal are removed for further cleaning in the Rheo fine coal plant. The 3x3h-in. clean coal is combined with the 4x3-in. coal from the No. 2 vessel, sized into 4x2 in., 2x1 34 in., and 1'/4x in., then sent to the loading booms. The 3x0-in. refuse from the primary launders is normally fed to the No. 1 dense medium circuit, but any portion or all of this material can, as an alternate, be processed in the Rheo rewash launder. The primary refuse when fed to the dense medium circuit is screened into YSXO which is cleaned in the fine coal plant and 3x for cleaning in the No. 1 vessel. The clean coal from this vessel is passed over a vibrating drainage and rinse screen, then sluiced to the rewash sizing shaker where it is dewatered and sized for loading. The installation of a pilot plant separating vessel using a suspension of magnetite in water was pro-

Jan 1, 1953

By D. J. Barrett, M. A. Sochocky

INTRODUCTION Summary of Factors Influencing Comminution Circuit Design The selection of an appropriate comminution circuit for a specific ore is one of the most important decisions in the design of a processing plant. The importance is related to the fact that the capital and operating costs for crushing and grinding plant generally represent, as is well known, the major portion of the plant costs. This chapter will, therefore, identify as many as possible of the factors which influence the selection of a comminution circuit. The number of factors which will have to be considered for any comminution project will depend, among other things, on the type of project. If, for example, the project is an entirely new mining development, then most, if not all, the factors identified will have to be analyzed. If the project is an expansion of a developed mining operation or if the new orebody is adjacent to a viable operation, then the existing operation will influence the choice of factors or design constraints which need to be considered. The existing infrastructure or supporting systems may be quite adequate to accommodate the requirements of any expansion or new development. Hence, those factors may not have to be considered. To cover, however, the widest spectrum of projects, the factors which have been identified in this chapter are those which will have to be considered for the most complex of projects, that of developing an entirely new mining operation. The range of factors is as broad as the range of different ore types. Thus, each development must be treated with individualized care. The most important step in the development is the analysis and understanding of the ore characteristics. The hardness of the ore, its abrasiveness, friability, moisture content, grade, mineralization including gangue mineralization, liberation size, chemistry, and other characteristics should be the first to be analyzed in the investigation. The next should be the determination of factors such as plant size, throughput, location, climate, accessibility, and availability of water. The selection of samples for initial bench scale work and bulk sampling (when needed) for further

Jan 1, 1982

By Frank Van Horn

IT is customary to ascribe two general modes of occurrence to natural gas, namely shale. gas which, as the name indicates, is found in' shale, and reservoir gas, which occurs ill sandstone, conglomerate and dolomitic limestone. Both of these types are found in the Cleveland district. The shale gas has been produced on a small scale for a long period of years, probably dating back as far as 1883. Shale gas is a low-pressure gas, small in volume with variable pressure, and is limited to no definite horizon. It is generally independent of oil, may last for a long time, and is not dependent to any great extent on the structure of the rocks. There are many such wells in the district which range from 400 to 1,840 ft. in depth, although most have been completed at about 800 ft. This indicates that the wells pass through the Cleveland and Chagrin shales into the Huron or Portage shale of the Upper Devonian. During the last 2 years great interest has developed in a deeper-seated reservoir gas. What is commonly called reservoir gas is generally a high-pressure gas occurring in large volume at a definite horizon. Oil may, or may not, be associated with the gas, and in most regions in which reservoir gas is found, the geological structure is of great importance. This type of gas occurs in all large fields such as those of West Virginia which have been supplying Cleveland until the recent discovery of local gas at great depths in commercial amounts.

Jan 1, 1917

By Robert Wamsley, W. E. Jones

One of the earliest problems in the life of any community is the provision of an adequate supply of water sufficiently free from all types of contamination to be suitable for domestic purposes. Generally speaking, the location of most communities is determined to a great extent by the availability of an adequate supply of satisfactory water. For a mining camp, that consideration cannot be foremost. Here, the ore takes first place, and the men who mine it must do the best they can under the existing conditions. If there is no local source of water, it must be brought from some distant source or must be found by sinking shafts or drilling wells. Fortunate indeed is the mining company that discovers a commercially valuable ore deposit beside a never failing creek full of pure water, with sufficient water rights available. because the acquisition of water in any other manner nearly always involves not only a considerable period of time but the expenditure of considerable money. The experience of Climax Molybdenum Co. demonstrates the measures that sometimes are necessary in order to provide a suitable supply of water. The Climax mine and mill are on the Continental Divide! about 13 miles northeast of Leadville. The elevation of the domestic part of the camp varies from a minimum of 11,320 ft. to a maximum of approximately 11,550 ft. above sea level, and, as is common at such altitudes, the near-by streams that might be suitable for a water supply are small and intermittent, usually flowing only during the summer months. The only streams of any size in the immediate vicinity of Climax are the Ten Mile and Arkansas Rivers The headwaters of Ten Mile River are on the Company's property, and its water has been used for the domestic supply. The headwaters of the Arkansas River are about 2 miles distant and have not been used as a source of supply by the company. During the past 11 years of the production of molybdenum at Climax, the number of families living there has increased from about 45 to 283, and the population has increased from about 200 to 1200 persons. Consequently, the capacity of the water-treatment facilities, and the amount of water available, had to be increased to meet the requirements of the camp. As early as 1932 it was recognized that the water in Ten Mile River would not continue to be adequate for domestic purposes and after considerable discussion it was decided to drive a drift through the major fault in an effort to find additional water. This drift was completed in 1935 and tapped sufficient water to make the supply adequate. This water was treated in a tank underground, where lime was added, and was then piped into the domestic supply lines. At about the time this line was completed, the presence of fluorine in harmful concentrations was discovered in the water. This problem was submitted to the International Filter Co. and in November 1937 a plant of its design was put in operation for treating the water to remove the fluorine. This plant proved entirely successful,

Jan 1, 1946

By A. J. M. Ross

BACKFILLING of stopes and other underground openings in the Homestake mine with sand tailings was undertaken primarily to reduce surface subsidence, which was wrecking much of the surface plant and a substantial part of the town, and to make possible maintenance of openings into the top of pillar stopes as mining progressed. The progress of this type of filling has been rapid and the results very satisfactory. Sand is now used in filling timbered stopes, shrinkage stopes, and abandoned drifts and crosscuts. A permanent pipe-line system for transporting sand tailings into the mine by gravity has been installed. The close filling of all stopes has resulted in important benefits other than the two major ones. The ore bodies in the Homestake mine occur as replacements in one distinctive layer of the metamorphosed pre-Cambrian sediments along a group of minor folds that together form a complex anticline that pitches at 35º to 40º to the southeast. The ore bodies are extraordinary for their magnitude. Widths of over 300 ft. have been mined and continuous ore has been followed for over 1200 ft. along the strike on some of the upper levels. Mining has been by shrinkage stoping with square-set mining of crowns and pillars. In the standard plan, shrinkage stopes 60 ft. in the direction of strike and the full width of the ore have been taken up to within 25 ft. of the level above. After filling, the crown has been mined by square-set methods, as have also the 40-ft. pillars between shrinkage stopes. In former days, when the supply of ore seemed inexhaustible, the mining of pillars was allowed to lag far behind because of the high cost. Many pillars were rather badly fractured on the level and in some places between levels. Coarse waste was used for backfilling all stopes, but in pillars it became increasingly difficult to maintain haulageways for the transportation of this fill over the top of the stopes as mining progressed The cost of maintaining these crosscuts was excessive and in many pillars practically impossible. Therefore it became the practice to fill pillar stopes by tapping the back and sides of the stopes.

Jan 1, 1939