Search Documents

By B. E. Terkelsen, B. J. Piearcey

A study has been made of the effect of unidirectional solidification on the creep behavior, stress-rupture properties, and thermal shock resistance of four nickel-base superalloys. The alloys Mar-MZOO, B-1900, IN 100, and TRW 1900 show improved rupture ductility and thermal shock resistance when tested with the columnar grains parallel to the major stress axis during test. The relative improvement in creep-rupture properties depends on the intrinsic strength of the alloy, a property which depends on composition, heat-treatnient, and crystallographic orientation. The data clarifies some of the factors affecting the properlies of the cast nickel-base superalloy. COMPONENTS designed for high-temperature use have, in recent years, been fabricated by precision casting techniques using nickel-base alloys developed specifically for use in the conventionally cast condition. This development was a result of both the increasing complexity of the component and the recognition that high-temperature strength was incompatible with workability. The use of castings can be economically favorable, but, more important, the recent complex designs of air-cooled gas turbine blades and vanes in alloys which possess the necessary high-temperature strength cannot be forged. Common modes of failure of high-temperature components are excessive creep, creep rupture, and thermal fatigue. If rupture occurs then the mechanism is usually by inter crystalline cracking along those grain boundaries oriented transverse to the major stress axis. In the stronger alloys, rapid propagation of intercrystalline cracks result in apparent premature failure demonstrated by the absence of third stage creep in a creep-rupture test and low rupture ductility. Tensile ductility shows a similar trend, that is, decreasing ductility with increase in strength. It is not surprising, therefore, that increases in creep strength have only been obtained with a loss in resistance to thermal shock, a property which shows a dependence on tensile ductility. VerSnyder and ~uard' showed that the application of unidirectional solidification to a brittle Ni-Cr-A1 alloy both improved the rupture life of the alloy and increased rupture ductility. Since this casting method results in columnar grains, it appeared that the solution to the lack of ductility in nickel-base alloy components was the elimination of the source of failure, namely the transverse grain boundaries. This concept was recently developed2 to produce cast-to-size gas-turbine blades and vanes consisting entirely of columnar grains oriented parallel to the major stress axis of the component. Not only did the process impart increased rupture life and ductility to the components, but it also increased their resistance to thermal shock. During this development, the effect of unidirectional solidification on the properties of several alloys was investigated. The resulting data allows certain conclusions to be drawn regarding the factors affecting the creep and stress-rupture properties of the cast nickel-base superalloy and also its resistance to thermal shock. Detailed information was obtained on the alloys Mar-MZOO, B-1900, In 100, and TRW 1900. The composition of the alloys studied are shown in Table I. MATERIAL PREPARATION AND TESTING The conventionally cast alloys are cast as +-in.-diam bars in innoculated shell molds under conditions designed to maintain control of grain size. Unidirec-tionally solidified casting were produced in the form of 3-in.-diam ingots. Specimens from the latter were machined such that the axes of the columnar grains were parallel with the axis of the test bar, except in certain cases where the transverse properties of the material were being evaluated. The specimens were tested in an axial loading creep machine.' Temperatures were measured with thermocouples, attached just outside each end of the gage length, to assure uniform temperature along the entire specimen. Chromel/alumel thermocouples were used up to 1800"F and Pt/Pt-10 pct Rh thermocouples above 1800"F. The specimen temperature was recorded and maintained within i2"F throughout the test. Creep extensions were measured automatically with extenso-meters attached to ridges on the specimen and recorded continuously using linear variable differential transformers and multipoint recording equipment. MICROSTRUCTURE The microstructures of transverse sections of the four alloys studied are shown in Figs. 1 and 2. Fig. 1 shows optical micrographs of the alloys, both in the conventionally cast and unidirectionally solidified conditions. Each alloy displays a cored dendritic structure, a distribution of MC carbide, and the presence of the y — y' eutectic constituent.~ In the case of IN 100 and B-1900, Fig. 1 indicates that in these specimens the eutectic is degenerate. That is, it consists only of y' pools indicating that the y constituent has been solutioned during the cooling period after solidification. The major effect of unidirectional solidification on the microstructures of the alloys is a tendency to promote a more dendritic form of MC carbide and an increase in dendrite arm spacing, both effects being a result of the slower solidification rate in the unidirectional solidification technique. V, lec tron micrographs of transverse sections of the four alloys in the two cast conditions are shown in

Jan 1, 1968

By Fred D. Fox

INTRODUCTION Approximately two years have elapsed since the first summary of the Grizzly Gulch Tailings Disposal Project was presented (1). Since that time, various physical modifications and additions to the existing treatment system have transpired. Further, Homestake and the entire mining industry have been impacted severely by additional modifications and additions concerning regulatory reform aimed at total disciplinary permitting and hazardous waste management. The following paper summarizes the past accomplishments relating to the Grizzly Gulch Tailings Disposal Project, correlating these accomplishments with future plans that are being developed to comply with regulations and to continue Homestake's commitment to environmental protection. The famous Homestake Gold Mine, located in Lead, South Dakota, has been operating in the Black Hills region for over a century, approximately 12 years before the south half of Dakota Territory was admitted to the Union as the State of South Dakota (2). During the 104 years of operational development, Homestake's Gold Mine, as well as the entire mining industry, have been influenced by numerous governmental regulations dating back to the Refuse Act of 1899 which regulated the deposit of debris from mines and stamp works. The enactment of the National Environmental Policy Act of 1969 may be thought of as the beginning of a long line of unplanned steps to deal with the many concerns of matters pertaining to the environment. Environmental awareness continued into the 1970’s, in which the Clean Air Act, Federal Water Pollution Control Act, Safe Drinking Water Act, Toxic Substances Control Act, and the Resource Conservation and Recovery Act (RCRA), to name a few, surfaced.

Jan 1, 1983

By S. S. Shen, M. J. Pool, P. J. Spencer

Heats of solution of silver and copper in dilute Ag-Cu-Sn alloys at 720°K have been determined using a liquid metal-solution calorieter. Values of the se2f-interaction coefficient n AgAghave been calculated at constant copper concentrations and n Cu Cuhas been determined at constant silver contents. The reliability of the experimental data is shown by the very good agreement between nCujAg and ij &$; these interaction coefficients have experimental values of -9100 and - 9590 cal per g-atom, respectively. Certain solution models are shown to be inadequate for prediction of solute interaction coefficients in dilute Ag-Cu-Sn alloys. In a previous publication' the results of a thermody-namic study of dilute Ag-Au-Sn alloys were presented. The present work represents the continuation of a program to investigate dilute alloys of the noble metals with tin and in particular is concerned with solute interactions in the Ag-Cu-Sn system. By determination of the magnitude and sign of the various interaction coefficients in dilute alloys it is possible to gain some understanding of the different types of solute-solute and so lute-solvent bonding changes that occur as the solute concentrations are varied. Hence systematic studies of alloys with similar physical characteristics as regards size, structure, electronegativity, and so forth, of their components can contribute a great deal to present theoretical knowledge of solutions. The recent definition of an enthalpy interaction coefficient, 11, by Lupis and Elliott2 is of particular value in calorimetric studies such as the present one: where j and i are solutes and s is the solvent; Si is the relative partial molar enthalpy of component i and x represents the mole fraction of solute or solvent. Values of ?Hi can be obtained directly by solution calorimetry and data for n are thus easily determined, often with a high degree of accuracy. ?Hi is related to the relative partial molar enthalpy at infinite dilution, ?Hi and to the enthalpy interaction coefficients by the expression: ?Hi?Hi + X;nz+ ... [2] The aim of the present work was to determine the self-interaction coefficients n AgAgand 178: in alloys of different compositions and also to establish values for n Agcg| and ncuAg. Since it is a thermodynamic requirement (resulting from the Maxwell-type relationships which can be applied to partial molar properties) that nAgcu and ncuAg should be equal, a further aim of this study was to demonstrate the agreement between experiment and theory. EXPERIMENTAL A description of the liquid metal-solution calorimeter used in this research has already been published,3 and no further details of its construction and operation will therefore be given here. Copper supplied by the American Smelting and Refining Co. was indicated by them as being 99.999 pct pure, and the silver obtained from A. D. Mackay, Inc., was also quoted as being 99.999 pct pure. A solvent bath consisting of between 70 and 80 g of 99.99 pct pure Sn was used for each series of experimental drops. Its weight was accurately determined and the appropriate amounts of copper or silver were added to give alloys of the desired composition. Approximately 0.00125 g-atom additions were used for determinations of the heat of solution of silver in the bath, while, for copper, specimens consisting of approximately 0.0015 g-atom were used. The heat capacity of the bath was determined at regular intervals during a series of drops using tin or tungsten calibration samples. The heats of solution of silver and copper in pure tin were first determined as a function of their concentration in order to establish the self-interaction coefficients 7AgAg and ncucu Alloys containing a constant 0.01, 0.02, 0.03, and 0.04 mole fraction of copper were then used to study 17:: in alloys of different copper content, while alloys of the same mole fractions of silver were used to determine equivalent data for 178: at constant silver concentrations. The composition of the bath was held at the desired copper or silver concentration by making calculated additions of the appropriate solute throughout the experiment. From the limiting values of ?HAg in the constant copper content alloys it was possible to study ?HAg as a function of xCu and hence to determine 42:. A similar analysis of the re, values permitted calculation of nAgcu. Heat content and heat capacity data from Hultgren et al* were used to calculate heat of solution values from the measured heat effects at the experimental temperature of 720°K. RESULTS AND DISCUSSION Determinations of ?HAg. A preliminary investigation of the heat of solution of silver in pure tin at 720°K was first made in order to establish the value of nAgAg before additions of copper were made and also to compare the value of ?HOAg(l) with that obtained in the previous study of Ag-Au-Sn alloys.' Then the heat of solution of silver in Cu-Sn alloys was investigated as a func-

Jan 1, 1970

SECTION I Page Page New York Section War Meeting on Employment xxxii Sulphur and Pyrite v Local Section News xxxiv War Minerals Committee xviii Forthcoming Meetings xxxvi St. Louis Meeting xx Library xxxvii Minutes, of Meeting, Executive Membership xli Committee xxvi Institute Committees Iv Members in Military Service xxvi Officers and Directors lxii Personal xxx

Jan 10, 1917

THE foundation established by the partners of the late Robert W. Hunt provides for both a medal and a prize. The latter has not been given before this year, and the first award is to C. H. Herty, Jr., for his several papers on the physical chemistry of the open-hearth process.. He is the son of the well known chemist of the same name. He was born at Athens, Ga., on Oct. G 1896, graduated from the University of North Carolina in 1918, and went into war service as foreman of U. S. Chemical Plant No. 4, at Saltsville, Va. In 1919 he went to Massachusetts Institute of Technology, where he was successively instructor, research assistant, and research associate in the School of Chemical En-gineering practice receiving his master's degree in 1921 and his Ph.D. in 1924. He continued his brilliant work on the physical chemistry of the open-hearth process, much of it being done in cooperation with the Bethlehem Steel Co. at its Lackawanna plant, and dealing with the elimination of sulfur. In 1926 he joined the staff of the U. S. Bureau of Mines, in charge of its ferrous metallur-gical work at Pittsburgh, and continues to be active in research work on the physical chemistry and metallurgy of the open-hearth process. His Institute publications are: Some Factors Affecting the Elimination of Sulfur in the Basic Open-hearth Process," "Chemical Equilibrium of Manganese, Carbon and Phosphorus in the Basic Open-hearth Process" and "Desulfurizing Action of Manganese and Iron," and he will present a paper on ?Effect of Temperature on the Solubility of Iron Oxide in Iron" at the annual meeting.

Jan 2, 1928

By G. Bhat, J. F. Libsch

lsoembrittlement curves depicting the influence of time and temperature in the range 800' to 1260°F (425' to 680°C) on the development of embrittlement in a commercial chromium alloy steel and a commercial molybdenum alloy steel are presented. Two distinct regions of embrittlement occur in the chromium alloy steel: I—at 800' to 1000°F (425' to 540°C) and 2—in the region just below the lower critical temperature. Embrittlement is most pronounced at 800' to 1000°F, decreasing very rapidly with increasing temperature above this region, only to increase again as the lower critical temperature is approached. The data suggest two distinct modes of embrittlement with possible superposition of the two modes at extended embrittling times in the temperature range 1100° to 1150°F (590' to 620°C). While the molybdenum alloy steel shows little susceptibility to embrittlement at 800' to 1000°F (425' to 540°C), considerable embrittlement may occur just below the lower critical temperature. THE subject of temper embrittlement in alloy steels has received considerable attention in the last few years. Points of view on the mechanism of embrittlement differ, however, resulting in part from the incompleteness of the data developed and in part from the speculation regarding the susceptibility of plain carbon steel to temper embrittlement. Libsch, Powers, and Bhat1 carried out short-time embrittling treatments on an AISI 1050 steel and demonstrated that hardened plain carbon steels are quite susceptible to embrittlement when tempered in the range from 850°F (455°C) to the lower critical temperature. The isoembrittlement diagram,' representing the embrittling characteristics of this steel, is reproduced in Fig. 1. It is evident from the shape of the curves shown that embrittlement in plain carbon steel increases progressively with both temperature and time in the embrittling range. A comparison of the isoembrittlement diagram for AISI 1050 steel with that presented by Jaffe and Buffum' for an SAE 3140 steel shows that up to 930°F (500°C) the isoembrittlement characteristics of the plain carbon steel are similar to those of SAE 3140 steel, although the embrittlement is much more severe in the latter steel. Above 930°F (500°C), the rate of embrittlement in the plain carbon steel increases continuously with increasing temperature; whereas, in the SAE 3140 steel, the embrittlement rapidly decreases. The influence of alloying elements upon embrittlement during tempering thus appears to cause a decrease in embrittlement above the region of maximum embrittlement, i.e., 850" to 1000°F. The question naturally arises as to what effect individual alloying elements have upon the embrittling characteristics of the plain carbon steel. Current knowledge on the influence of alloying elements on temper brittleness may be found in the review papers of Hollomon" and Woodfine. Hollo-mon," from the results of other investigators, has shown that, in general, the amount of embrittlement increases with increasing alloy content (except for molybdenum and possibly tungsten and columbium). Jaffe and Buffum," by a comparison of the embrittlement in a plain carbon steel with that of a SAE 3140 steel postulated that the presence of alloying elements in moderate amounts tends to retard the development of temper brittleness. It is difficult to determine what effect chromium has upon temper brittleness, since most of the information available has been based on the combined effect of other elements with chromium, particularly nickel and manganese. However, Wilten, and recently Jolivet and Vidal,' Vida1, and Woodfine have reported that chromium steels are temper brittle, that the embrittlement is reversible with a maximum rate of embrittlement at approximately 975°F (525"C)," and that the susceptibility increases with increasing amounts of chromium. Taber, Thorlin, and Wallacel" have found a large embrittling effect with increasing chromium content in a medium C-Mn-Ni steel. But Hultgren and Chang," from their experiments conducted on synthetically prepared ternary Fe-C-Cr alloys, could not conclude that these alloys are susceptible to temper embrittlement. However, on addition of manganese or phosphorus, these Fe-C-Cr alloys became susceptible, from which fact they concluded that the embrittlement developed in chromium-bearing Fe-C alloys is due chiefly to the presence of these elements. Considerable data are available to show that molybdenum decreases the susceptibility of steel to temper embrittlement. However, its effectiveness in preventing or decreasing embrittlement appears limited to its presence in small amounts. Vidal" has shown that a plain 2 pct Mo steel was susceptible. Hultgren and Chang" also have shown that molybdenum additions in excess of 2 pct to synthetically prepared Ni-Cr steels did not prevent embrittlement. Jolivet and Vidal' and Lea and Arnold found that molybdenum reduced temper brittleness. Lea and Arnold further stated that molybdenum decreased the rate of embrittlement rather than the total amount of embrittlement, whereas Preece and Carter" have shown that the presence of molybdenum greatly reduces the equilibrium extent of the change at a given temperature but does not appear to influence the rate of embrittlement. There appears to be very little information as to how molybdenum by itself affects the temper brittleness susceptibility of a plain carbon steel.

Jan 1, 1956

By E. I. Gordon

The electronic pickup tube is the image-to-video signal-converter or transducer in tele vision-like systems. Images may relate to visible light or IR excitation as in conventional TV systems, X-ray excitation as in some medical and production control applications, or electron excitation as in electron microscopy. The latter process is also important in some forms of light or X-ray sensitive pickup tubes as an intermediate step. In virtually all of these devices the image ends up as a stored charge pattern on a suitable target electrode and the video signal is created by periodically scanning the target with a low energy electron beam and removing the stored charge. In a major group of tubes radiation induced conductivity creates the charge pattern. In others, photoemission is used. In this paper an attempt is made to illuminate some of the device requirements placed on materials exhibiting radiation induced conductivity, some of the materials and techniques that are used, and the problems. The emphasis will be on visible light and IR sensitive targets although some attention will be given to X-ray and electron imaging. Photoconducting films as well as diode arrays will be discussed. ELECTRONIC pickup tubes find their greatest use in commercial, entertainment television, and in industrial and educational closed-circuit television. Video telephone systems, such as AT&T's PICTURE-PHONE System will become eventually the greatest user. Military use is also very important. Nevertheless the use of electronic pickup tubes in technology, science, and medicine is assuming ever greater relevance and demands the greatest diversity and perfection in the pickup tube art. Commercial television and closed-circuit television use requires visible light response, high resolution, low lag, and uniform response. Video telephone use requires the same plus extreme reliability, stability, and low cost. Military use emphasizes, in addition, sensitivity, IR response, and ruggedness. (Devices for far IR response will not be considered here.) The use of pickup tubes in medicine and biology emphasizes UV response for microscopy, X-ray response for radiology, and energetic electron response for electron microscopy. Astronomy and nuclear physics demands low light level response, storage ability, and resolution (here the tube is a successful replacement for film). The interested reader might profitably read Advances in Electronics and Electron Physics, vol. 12,' 16,2 and 22A3 and 22B4 for detailed discussion of the use, properties, and technology of electronic pickup tubes. In general, because of the importance of these uses, none of the above properties will be ignored. Nevertheless attention will be restricted to only those imaging devices, called pickup tubes, using a scanning electron beam to dissect the image with a resulting video signal for conventional CRT display. However pickup tubes have become so complex that many of them include components such as image in-tensifiers which would be normally excluded by this restriction. Thus some of the other imaging devices will not be ignored entirely. We will first review the fundamental elements and physical phenomena involved in modern electronic pickup tubes, then the relevant materials and some of the material problems and then an interesting goal yet to be achieved. REVIEW OF PICKUP TUBE PRINCIPLES In all modern television systems using pickup tubes there is an interval called the frame interval, during which the incoming radiation flux is allowed to produce a cumulative effect in the form of a stored charge pattern which is a replica of the radiation image, and a scan interval during which the stored charge pattern is converted into a video signal. The frame interval bears no fixed relation to the scan interval and may be shorter or longer. In conventional, real time television the scan interval including retrace is identical to the frame interval. Integration and storage is the key to the sensitivity of modern pickup tubes, in contrast to earlier tubes such as the image dissector. At equivalent light levels and without integration, the number of photons contributing to the video signal in the image dissector is lower by a factor approximating the number of picture elements in the displayed image, a number of order 10. Statistical fluctuations in the number of contributing photons represent a serious limitation to the attainable signal to noise ratio, resolution and contrast. As a result considerably greater light levels have to be used then in targets which integrate over the full frame period. Thus the crucial elements, common to all modern pickup tubes, are the charge storage surface and the scanning electron beam which is incident on the charge storage surface at very low energy. These are shown in Fig. 1(a). The charge storage insulator is generally very thin with a thickness of several microns or less. The surface of the insulator is held near cathode potential. The backplate potential is held at cathode potential or at a small positive voltage relative to cathode. The combination of storage insulator and backplate electrode is commonly called the "target". In the absence of incident radiation flux the electron beam scans over the storage surface depositing negative charge uniformly over the scanned part of the surface by virtue of the fact that the effective secondary

Jan 1, 1970

By Robert Bell

THE " Tar-Sands." is the name which has been given to the extensive horizontal deposit of fine Cretaceous sand, blackened by tarry petroleum, which forms the banks of the last or lowest 130 miles of the Athabasca river before it terminates in Athabasca lake. The Cretaceous strata, to which these sands belong, extend northwesterly from Dakota all the way to this lake and for 500 miles beyond it. The Athabasca river forms the uppermost section of the Athabasca-Mackenzie, one of the great rivers of the world. It rises on the Pacific side of the Rocky mountains, westward of Edmonton, and flows north of east to a point called Athabasca. Landing, 100 miles north of Edmonton, where it turns northward and runs about 280 miles before it falls into the west end of Athabasca lake. The section of this river-system which discharges the lake just named into Great Slave lake, is called Slave river, and below the latter lake it becomes the Mackenzie river. Along the section of 280 miles of the Athabasca river above mentioned, the Cretaceous strata consist of bluish-gray and drab-gray marls, on top, from Athabasca Landing to Drowned rapid, 110 miles down stream; then heavily bedded gray sandstones, 225 ft. in greatest thickness, underlying these, form the banks for about 40 miles further. The strata appear to be horizontal, but they really clip very slightly to the southward. At Drowned rapid, we see the first of the tar-sands resting on almost horizontal beds of bluish-gray limestone of Devonian age. In some places the limestone is associated with shaly or marly bands. Notwithstanding the great hiatus between the two series, the horizontal tar-sands lie conformably upon the almost level upper beds of the limestone wherever the two formations are seen together, all along the river, throughout a

Mar 1, 1908

By Robert Anderson Cook

AS the margin of profit in the manufacture of iron continues to decrease, attention is called more and more to economies in every department. Beginning at the bottom, in the preparation of the ore at the mine, me notice a general tendency is towards the shipment of richer ores, securing to the mine-owner a better price per ton, which the purchaser is glad to pay by reason of the saving in freight of iron, and in the cost of reduction, which depends so largely upon the amount of fuel and flux, and the productive capacity of the plant. In other words, the difference in value between rich and poor ores is much greater than their relative percentages of iron indicates; because the barren material in a lean ore is not merely worthless, it is a positive source of expense, requiring transportation, handling, fluxing, smelting, and its due share of general expenses; in return for which it yields nothing and decreases the available capacity of a given plant and capital for profitable work. The enriching of the ore is done in most places by hand-picking, and in a few by wet concentration; but the managers of several magnetite mines in Sweden have been practically successful in doing it by machinery. The only magnetic separating machine which has actually taken the place of hand-picking was designed and patented by Mr. Jonas Wenström of Örebrö, Sweden. In this machine, which is illustrated in Figs. 1 and 2, Mr. Wenström has taken advantage of the property of soft iron to become magnetized by induction. The machine consists of a barrel made up of soft iron bars and some non-conducting material (usually wood), which is rotated around a stationary shaft by means of a cog-wheel. Inside of this barrel, on the shaft, is placed eccentrically a cylindrical electro-magnet, provided with a number of manges (N, S, Fig. I), between which wire is wound in such a manner that the flanges are of negative and positive polarity, being energized by a current passing through the wire coils from a small dynamo. As will be seen in Fig. 1, the flanges, N, S, are circular, and follow the internal contour of the barrel on the front side, while on the opposite side they are cut down to the line B, B' in Fig. 2. Hence the bars of the revolving barrel on the front side of the machine are mag-

Jan 1, 1889

In cooperation with the United States Bureau of Mines and the Idaho Bureau of Mines and Geology, the University of Idaho offers in the School of Mines a number of fellowships. These fellowships are open to college graduates who have had good training in mining, metallurgy, or chemistry, and who are qualified to undertake research work. The income of each fellowship is $720 a year for the 12 mo. beginning July 1, 1919. Fellows will register as students in the University of Idaho and become candidates for the degree of Master of Science in Mining or Metallurgy (unless this or an equivalent degree has been earned). Their class work-will he directed by the heads of the departments of instruction, but the greater portion of their time will be spent in research work under the direction of the Bureau of Mines staff resident at the University. The purpose f this work is to undertake the solution of definite problems confronting the mining and metallurgical industries of the State of Idaho. For 1919-20 the following subjects are being considered: 1. Flotation-with especial reference to differential separation of various minerals. 2. Availability of western wood oils for flotation purposes. 3. Treatment of the complex gold-silver ores of southern Idaho. 4. Ore-dressing problems. 5. Mining problems. Applications, with certified copy of collegiate record, statement of professional experience, and names and address of three references, should be addressed to The Dean. School of Mines. Moscow Idaho_

Jan 6, 1919

By Richard R. Zupp, David A. Stevenson

An experimental method to determine the carbon activity in various solid solutions was developed. Samples of the solid solutions and an Fe-C reference sample were equilibrated with respect to carbon content by annealing them in a Hz-CHI gas mixture in a closed cell. The carbon content of each sample was determined, and the carbon activity was obtained from the carbon content of' the reference sample and well-established data for the dependence of the carbon activity on the carbon content in Fe-C alloys. The influence of vanadium on the activity of carbon in austenitic Fe-C-V alloys at 1000°C was determined by this technique. A general semiempirical correlation was developed to describe the dependence of the activity coefficient of- carbon on the composition of ternary austenitic iron-base alloys containing interstitial carbon and a substitutional solute. The correlation is particularly useful in predicting the partitioning of- carbon between various alloys. THE influence of substitutional solutes on the activity of interstitial solutes in metallic solid solutions is important in the theory of alloy phases. Solid solutions of particular interest are the fcc austenite phases of ternary Fe-C-Z systems, in which carbon is the interstitial solute and Z represents any substitutional solute. Carbon-activity data are also needed in these solid solutions to solve practical problems; the quantitative treatment of diffusion-controlled transformations' is an examvle. Experimental information is available for ternary austenitic solid solutions containing Mn,2 Si,2 and A16 as the substitutional solute. Because qualitative preliminary studies indicated that vanadium appreciably decreases the carbon activity,14 the present investigation was undertaken to determine the influence of vanadium on the activity of carbon in austenite. Although Flender and ever" measured carbon activity over a range of compositions in the Fe-C-V system, they were primarily interested in determining phase boundaries in the ternary system, so most of their measurements were outside the composition range for stability of single-phase austenite. Petrova and Shvartsman' also made limited measurements of the carbon activity in Fe-C-V alloys. The dependence of the carbon activity on the carbon content of an alloy may be determined by passing COCOz or H2-CH4 gas mixtures of carefully measured composition over the alloys, determining their equilibrium carbon content, and utilizing the relevant equilibrium relationships. smith16 used this technique with both CO-COZ and HZ-CH4 gas mixtures to determine the dependence of carbon activity on carbon content in pure Fe-C alloys. His data, which are in good agreement with those of some previous and subsequent investigators,6'17 but not with those of others,lfl'ao are usually considered to be the most reliable. Although the same method can be applied to Fe-C-Z alloys, it is difficult experimentally, because the appropriate gas mixtures are almost pure CO or Hz. A simpler technique is to simultaneously equilibrate the Fe-C-Z alloys and pure Fe-C alloys with the gas mixtures, and then use Smith's data to determine the carbon activity in the pure Fe-C alloy. A number of investigators have employed this technique. others Have used the partitioning of carbon at the interface of a diffusion couple prepared from an Fe-C alloy and a Fe-C-Z alloy. In the present study, a closed-cell method was developed by which carbon was selectively transferred via a gas medium between pure Fe-C alloys and Fe-C-V alloys which were not in physical contact. A similar method was developed independently by Heckler and winchel14 and used to study the Fe-C-Ni system. EXPERIMENTAL METHOD A schematic diagram of the experimental arrangement is shown in Fig. 1. In a typical experiment, a 5-g Fe-C sample was placed in one compartment of a quartz cell, and a 5-g Fe-V sample was placed in each of the other compartments. The cell was evacuated, outgassed, backfilled with approximately 125 Torr of hydrogen, and sealed. After being placed in a fur-

Jan 1, 1967

By Alfred Weiss

Over the past 25 years hard-rock mining companies have developed a number of profitable computer applications which appear applicable to operations in the coal industry. The evolution of these applications are described and the most profitable discussed. The basic nature of these systems is that they must cut across organizational boundaries. While technological advances contributed significantly to the successful implementation of computers within mining, the human aspects related to organization, management and control of systems projects remain as key to future success in coal as they were and still are in hard-rock mining.

Jan 1, 1983

By Samuel M. Cassidy, John A. Garcia

IN some districts of the bituminous coal field the problem of constructing bulkheads to seal off water under pressure is becoming increasingly important. Recently this matter has been brought very much to the front by the loss of a large Illinois mine due to failure of a bulkhead that separated it from several old, flooded mines. As this great misfortune has provoked much inquiry about proper bulkhead design, it is felt that a description of the successful and extensive water-sealing practice at three mines that have different natural conditions will be of considerable interest to those connected with properties having a present or future water problem and to engineers that may have to design safe bulkheads of economical construction. These three mines are the Saxton and Dresser, near Terre Haute, Ind., and the Hegeler, near Danville, Ill. All three have water conditions that make it necessary to regularly seal off all worked-out sections of the mine, and there are considerably over a hundred bulkheads in each. As far as the writers know, these three mines are the only ones in the bituminous coal fields of the United States with anything like so large a number of water seals and experience, although a number of other mines are known to have a few bulkheads. More detail will be included herein on the Saxton mine than on the others, as the writers are more familiar with it. General Mining System All three of the mines use the same general panel room-and-pillar system, which consists of rooms turned both ways off room entries and a solid block of coal left on all sides of the completed panel except on the cross-entry side, where a heavier pillar is pierced by two entries for haul- age and air. On completion of the panel the two entries are sealed and the panel is then isolated from the rest of the mine. Owing to water conditions, no pillars are pulled; recovery inside the panel barrier pillars is approximately 65 per cent.

Jan 1, 1937

Jan 1, 1900

Jan 1, 1941

By Bruce W. Gonser

TIN is not yet classed as a rare metal, but it has taken a long stride in that direction in the last ten months. It is now in Group 1 of the War Production Board's critical list, along with such company as magnesium aluminum, and nickel. This is in sharp contrast with the position a year ago when the supply well exceeded demand, and tin was used when feasible in place of really scarce metals. The geographical sources of tin production in recent years are shown in Table 1. Preponderance of former production in southeastern Asia, particularly Malaya and the Netherlands Indies (but all now controlled by the Japanese). is entirely too marked to be funny. Of the 1940 known world production of 237,000 long tons nearly all was controlled by the United States, Great Britain, and their friends. Now their supply is from countries that produced only 28 per cent of that amount. This excludes China and Australia, which because of shipping difficulties and local consumption, cannot be expected to export much tin. In spite of some expected increase in production, therefore, the supply is, and will continue to stay for at least several years, way below that desired for even normal uses. Although deliveries to consumers in the United States alone

Jan 1, 1942

By Harry C. Wiess

RECENT announcement of further restrictions on gasoline consumption in the Mid-West and Southwest has focused public attention on current discussions of an oil scarcity. Conflicting arguments are advanced on the one hand that we have plenty of oil and will not need to restrict consumption as soon as transportation facilities are adequate, and on the other hand that a great impending shortage will require most drastic reductions in civilian consumption in order to provide adequate supplies for military purposes. Data can be presented to support both views, the result being that the public is confused and uncertain of where the truth lies. For a nation with about half of the known crude-oil reserves of the world and two thirds of the total production it seems almost incredible to the layman that any shortage can exist. Those familiar with estimates of future demand. however. show increasing concern regarding our ability to meet military demands without further restrictions in civilian use or wasteful production from our remaining reserves. Only by considering such facts as are available and can be made public can a true appraisal be made of whether or not we are faced with a shortage that will amount to a crisis in crude oil.

Jan 1, 1943

By W. M. Mobley

The coal industry in Alabama, centered in Birmingham, has pioneered coal-bene-ficiation practice in the United States. The nature of the coal seams and mining methods employed have necessitated use of equipment and methods best adapted to the local conditions. Although all of the 30 or more coal seams now being mined in the state receive beneficiation, only the three most important producers of coking coals, the Pratt, Mary Lee and Black Creek, are discussed in detail. Nature of the seams, washability characteristics and equipment used are given as examples of the extent of work and progress in this field. The coal seams in Alabama are relatively thin and pitching, making mining difficult and expensive. Most of them are characterized by thin partings of rock or shale in the seam itself, as well as laminations of bone and rash. Mechanical mining methods have increased the occlusions from roof and floor to such an extent that nearly all the coal mined in the state must receive some treatment before it can be put on the market. During the year ending Sept. 30, 1943,' 18,129,792 tons of coal were mined in the state and 14,364,177 tons, or 79.2 per cent, received treatment. Excluding from the total the 1,223,014 tons produced by small wagon mines and the hand-picked lump coal, the amount re- ceiving beneficiation would be more than 90.00 per cent. This is, by far, greater than in any other coal-producing state. The earliest record of coal beneficiation in Alabama was the installation in 1890 of an experimental Lurig washer by Alexander Cunningham, for the Sloss Iron and Steel Co. at its blast furnace in Birmingham.2 In 1894 the Jeffrey Manufacturing Co. introduced the English Robinson washer, a combination of a hydraulic classifier and centrifugal machine. Erskine Ramsay, who has contributed so much to the coal industry, saw its possibilities as well as its mechanical defects and soon had his inventive mind at work. He added a sludge tank of his own design, and many Robinson-Ramsay washers were installed in Alabama and other states. The Stewart jig appeared in 1900, followed by the Montgomery jig in 1910 and both have found extensive use. Increased interest in this field led to new designs, such as the American, Elmore, Burke and Faust. The first Baum-type Norton jig was operated in 1930 and within the last five years six large installations of this type have been made by the McNally-Pitts-burg, Jeffrey and Link-Belt Companies. Wet-washing tables were introduced in 1922 but not extensively used until recently. The two most popular types are the Deister-Overstrom and Deister Plat-O. The coal-cleaning equipment used in Alabama has been relatively simple, yet efficient, but as the amount of impurities in the raw coal has been increased by mechanical mining and labor costs have become higher, much interest has been shown in sand cones, froth flotation and

Jan 1, 1947

By W. M. Mobley

The coal industry in Alabama, centered in Birmingham, has pioneered coal-bene-ficiation practice in the United States. The nature of the coal seams and mining methods employed have necessitated use of equipment and methods best adapted to the local conditions. Although all of the 30 or more coal seams now being mined in the state receive beneficiation, only the three most important producers of coking coals, the Pratt, Mary Lee and Black Creek, are discussed in detail. Nature of the seams, washability characteristics and equipment used are given as examples of the extent of work and progress in this field. The coal seams in Alabama are relatively thin and pitching, making mining difficult and expensive. Most of them are characterized by thin partings of rock or shale in the seam itself, as well as laminations of bone and rash. Mechanical mining methods have increased the occlusions from roof and floor to such an extent that nearly all the coal mined in the state must receive some treatment before it can be put on the market. During the year ending Sept. 30, 1943,' 18,129,792 tons of coal were mined in the state and 14,364,177 tons, or 79.2 per cent, received treatment. Excluding from the total the 1,223,014 tons produced by small wagon mines and the hand-picked lump coal, the amount re- ceiving beneficiation would be more than 90.00 per cent. This is, by far, greater than in any other coal-producing state. The earliest record of coal beneficiation in Alabama was the installation in 1890 of an experimental Lurig washer by Alexander Cunningham, for the Sloss Iron and Steel Co. at its blast furnace in Birmingham.2 In 1894 the Jeffrey Manufacturing Co. introduced the English Robinson washer, a combination of a hydraulic classifier and centrifugal machine. Erskine Ramsay, who has contributed so much to the coal industry, saw its possibilities as well as its mechanical defects and soon had his inventive mind at work. He added a sludge tank of his own design, and many Robinson-Ramsay washers were installed in Alabama and other states. The Stewart jig appeared in 1900, followed by the Montgomery jig in 1910 and both have found extensive use. Increased interest in this field led to new designs, such as the American, Elmore, Burke and Faust. The first Baum-type Norton jig was operated in 1930 and within the last five years six large installations of this type have been made by the McNally-Pitts-burg, Jeffrey and Link-Belt Companies. Wet-washing tables were introduced in 1922 but not extensively used until recently. The two most popular types are the Deister-Overstrom and Deister Plat-O. The coal-cleaning equipment used in Alabama has been relatively simple, yet efficient, but as the amount of impurities in the raw coal has been increased by mechanical mining and labor costs have become higher, much interest has been shown in sand cones, froth flotation and

Jan 1, 1947

PROF RICHARD ÅKERMAN Stockholm, Sweden DR. FRANK DAWSON ADAMS Montreal, Canada PROF RICHARD BECK Friberg, Germany ANDREW CARNEGIR New York, N.Y. DR. JAMES DOUGLAS New York, N.Y. PROF HATON DE LA GOUPILLIERE Paris, France SIR ROBERT A. HADFEILD London, England PROF HANS HOFFER Leoben, Austria JAMES FURMAN HOEFER Leoben, England PROF HENRI LOUIS LE CHATELIER Paris France

Jan 1, 1917