Search Documents

By Messrs. von Jonstorff

Continued Discussion of the Paper of Messrs. von Jonstorff, Blair, Dillner and Stead, presented at the New York Meeting of the Iron and Steel Institute, October, 1904.* (Bethlehem Meeting, February, 1906.) CLEMENS C. JONES, Richmond, Va. (communication to the Secretary+) :-In the chapter of this paper entitled "Method for the Determination of Phosphorus," by Andrew A. Blair, a form of the reductor used by Mr. Blair is illustrated. This form was employed by me in my earliest experiments, and abandoned after my adoption of the final apparatus described in my paper on the subject in 1889. The results reported by Mr. Blair are very closely accordant; but my experience was that, in the use of this form, a loss of the solution, amounting to almost a cubic centimeter, was occasioned by minute bubbles of hydrogen rising to the surface, and there exploding. My final reductor was designed to prevent this loss; and the most satisfactory results were obtained with a reductor having the open cup replaced by a bulb-shaped receptacle, provided with a glass stopper, similar to that of a separatory funnel of similar capacity, as suggested in a foot-note in my original paper. In my experience, the use of this later form of reductor repeatedly gave duplicate results which were, coincident to the fourth decimal place. R. W. RAYMOND, New York, N. Y.:-The. remarks of Mr. Jones recall to my mind an interesting part of the history of the Institute, and, of its relation to modern progress in the department covered by this interesting and valuable paper. In

Mar 1, 1906

By Bradley Stoughton, M. Miyake

The importance of magnesium alloys as engineering materials has increased rapidly in the past few years. The most important properties of magnesium alloys are their lightness and strength, which result in their extensive use in aircraft and automobile construction. Recent progress in the metallurgy of magneaium seems to offer hope of the production of the pure metal at a reasonable cost. The use of magnesium would doubtless increase greatly if it could be produced at a cost comparable with that of aluminum. A preliminary survey of the magnesium-base alloys shows that the most promising from a practical standpoint are magnesium-aluminum and magnesium-zinc as binary alloys, and magnesium-zinc-aluminum as ternary alloys. The research reported in this paper is a preliminary study of binary magnesium-aluminum and magnesium-zinc alloys, as an introduction to a series of further investigations. Magnesium-aluminum System The magnesium-aluminum system was first studied by Boudouard,1 who merely determined the liquidus. An accepted constitutional diagram was given by Grube,2 who found a compound A13Mg4 (melting point = 462.7" C.) and two eutectics at 35 per cent. magnesium (451.6° C.) and at 68 per cent. magnesium (440" C.) Between the first eutectic and the compound a solid solution exists. This diagram was checked or supplemented by Pécheux,3 Broniewski,4 Eger,5 Schirmeister,6 Voge17

Jan 1, 1926

By J. S. Vanick

An extremely hard, tough, and strong, white or chilled cast iron has been applied for the past several years to industrial and mining services in which its unusual properties have been confirmed by its ability to deliver in many instances much better performance than plain chilled iron, or other wear-resistant materials. It is being produced regularly by alloying a good base composition of chilled or white cast iron with essentially 4 to 6 per cent of nickel and 1 to 2.5 per cent of chromium. Such a material can attain a hardness exceeding 600 to 750 Brinell as against 380 to 530 for corresponding grades of plain chilled iron. The strength is approximately doubled and the toughness significantly increased. These properties make it especially useful for many applications requiring a high hardness for resistance to wear, abrasion, attrition, deformation; to some extent to high compressive loading and to a lesser but important degree to corrosive action. A wide variety of commercial castings is being successfully produced from this iron, ranging in size from the small grain-grinding plates or burrs through medium-sized castings such as sand pumps up to large, heavy castings such as rolls for metal rolling or cement grinding. The composition of this white cast iron may be roughly bracketed within the range shown in Table 1.

Jan 1, 1933

By Wheeler Davey

WHEN metals are subjected to mechanical working, such as rolling, one of the phenomena that take place is a movement of the crystals of the metal into a system or systems of orientation which bear an angular relation to the direction of working. In rolled metal the crystals may orient themselves with respect to the rolling plane or the rolling direction, or both. Direct evidence of the existence of preferred orientations in rolled metal has been obtained by numerous investigators from X-ray patterns of the rolled metal. Most of these workers used a monochromatic pinhole method. Where the degree of preference for a single orientation is high the monochromatic pinhole pattern may be interpreted by a geometrical calculation based on the angular relationships of the planes in the crystal and the diffraction arcs on the X-ray pattern. This process may be aided by the geometrical construction of the locus sphere (Langenkugel), and reflection circles of Polanyi,1 Polanyi and Weissenberg,2 and Mark and Weissenberg,3 and of the plane polar figures (flachenpolfigur) of Franz Wever.4 R. M. Bozorth5 solves X-ray patterns from metals having a single preferred orientation by means of a series of charts which when placed over the X-ray pattern give directly certain angular relationships, between the crystal planes and the surface of the specimen.

Jan 1, 1929

By E. M. Wise

THE properties required of gold alloys for jewelry are not well standardized, due in part to problems peculiar to certain branches of the jewelry industry, in part to the individual preference of the fabricator and to his willingness to cope with certain difficulties in manufacture, which arise with the use of certain alloys. GENERAL REQUIREMENTS In general, the properties desired may be classed as follows: 1. Color should conform to the dictates of good taste and smart style. 2. Corrosion resistance and tarnish resistance should be good. This is to a considerable extent determined by the carat. Resistance to such corrosive agents as mercuric chloride as well as certain depilatories is unreasonable to expect and difficult to meet. 3. Strength and hardness must be adequate to maintain the delicate contours of finely modeled jewelry. 4. Wear resistance must be great enough to resist abnormal wear, such as is encountered by a wedding ring in a lifetime of wear. 5. Ductility must be sufficient to permit the fabrication of drawn shells, tubes and difficult shapes. Material having a yield point of not less than 60,000 lb. per sq. in., an ultimate strength of 100,000 lb. per sq. in., and an elongation of 40 per cent. is desirable. 6. Melting point should be between 800° and 1200° C.

Jan 1, 1928

By Harrison Schmidt

Since the U. S. Geological Survey published the data on the Central Mining District collected by Lindgren and Gratonl and by Paige2 much new information has been obtained by development and mapping, but none of it had been published until recently when Kniffin3 published on Fierro, Lasky4 on the Ground Hog mine, Thorne5 on Santa Rita and Landon6 filed a thesis on the Fierro-Hanover-Santa Rita area at the University of Chicago. During the years 1927-1930 much of the writer's time was spent in mapping the geology and ore deposits of this district, particularly in the area of the zinc deposits at Hanover. Some of the data collected are presented here. Previous publications have been freely drawn upon and additional data used that were generously supplied by L. M. Kniffin, Wilfred Wright and Gerald Ballmer. Thanks are due Augustus Locke, Samuel G. Lasky, Kniffin, Wright and Ballmer for suggestions and critical readings of the manuscript, and to the Empire Zinc Co. (a subsidiary of the New Jersey Zinc Co.) for the privilege of publishing material compiled largely at its expense. The relation of the Central or the Santa Rita-Hanover-Fierro district to the Silver City district is shown on Paige's geologic map in the Silver City folio.7 Granodiorite porphyry and quartz-monzonite porphyry

Jan 1, 1935

By Harrison Schmidt

Since the U. S. Geological Survey published the data on the Central Mining District collected by Lindgren and Gratonl and by Paige2 much new information has been obtained by development and mapping, but none of it had been published until recently when Kniffin3 published on Fierro, Lasky4 on the Ground Hog mine, Thorne5 on Santa Rita and Landon6 filed a thesis on the Fierro-Hanover-Santa Rita area at the University of Chicago. During the years 1927-1930 much of the writer's time was spent in mapping the geology and ore deposits of this district, particularly in the area of the zinc deposits at Hanover. Some of the data collected are presented here. Previous publications have been freely drawn upon and additional data used that were generously supplied by L. M. Kniffin, Wilfred Wright and Gerald Ballmer. Thanks are due Augustus Locke, Samuel G. Lasky, Kniffin, Wright and Ballmer for suggestions and critical readings of the manuscript, and to the Empire Zinc Co. (a subsidiary of the New Jersey Zinc Co.) for the privilege of publishing material compiled largely at its expense. The relation of the Central or the Santa Rita-Hanover-Fierro district to the Silver City district is shown on Paige's geologic map in the Silver City folio.7 Granodiorite porphyry and quartz-monzonite porphyry

Jan 1, 1935

Since the U. S. Geological Survey published the data on the Central Mining District collected by Lindgren and Gratonl and by Paige2 much new information has been obtained by development and mapping, but none of it had been published until recently when Kniffin3 published on Fierro, Lasky4 on the Ground Hog mine, Thorne5 on Santa Rita and Landon6 filed a thesis on the Fierro-Hanover-Santa Rita area at the University of Chicago. During the years 1927-1930 much of the writer's time was spent in mapping the geology and ore deposits of this district, particularly in the area of the zinc deposits at Hanover. Some of the data collected are presented here. Previous publications have been freely drawn upon and additional data used that were generously supplied by L. M. Kniffin, Wilfred Wright and Gerald Ballmer. Thanks are due Augustus Locke, Samuel G. Lasky, Kniffin, Wright and Ballmer for suggestions and critical readings of the manuscript, and to the Empire Zinc Co. (a subsidiary of the New Jersey Zinc Co.) for the privilege of publishing material compiled largely at its expense. The relation of the Central or the Santa Rita-Hanover-Fierro district to the Silver City district is shown on Paige's geologic map in the Silver City folio.7 Granodiorite porphyry and quartz-monzonite porphyry

Jan 1, 1935

By Harrison Schmidt

Since the U. S. Geological Survey published the data on the Central Mining District collected by Lindgren and Gratonl and by Paige2 much new information has been obtained by development and mapping, but none of it had been published until recently when Kniffin3 published on Fierro, Lasky4 on the Ground Hog mine, Thorne5 on Santa Rita and Landon6 filed a thesis on the Fierro-Hanover-Santa Rita area at the University of Chicago. During the years 1927-1930 much of the writer's time was spent in mapping the geology and ore deposits of this district, particularly in the area of the zinc deposits at Hanover. Some of the data collected are presented here. Previous publications have been freely drawn upon and additional data used that were generously supplied by L. M. Kniffin, Wilfred Wright and Gerald Ballmer. Thanks are due Augustus Locke, Samuel G. Lasky, Kniffin, Wright and Ballmer for suggestions and critical readings of the manuscript, and to the Empire Zinc Co. (a subsidiary of the New Jersey Zinc Co.) for the privilege of publishing material compiled largely at its expense. The relation of the Central or the Santa Rita-Hanover-Fierro district to the Silver City district is shown on Paige's geologic map in the Silver City folio.7 Granodiorite porphyry and quartz-monzonite porphyry

Jan 1, 1935

By D. J. Carney, E. Richard Randolph, E. Van Meter, J. J. Oravec, Stanley H. Ward, Gerald J. Anderson, Rolland L. 203-000-000-005 Blake

DURING the last 30 years the inductive electromagnetic method has been used chiefly in the search for massive sulphide mineralization. This application has met with varying degrees of success and in recent years has resulted in discovery of several large orebodies. Little has been written concerning its use in exploration for soft iron ores, but one of the present authors has reported on experiments with massive magnetic deposits.' To augment the exploration tools available to geologists in delineating iron orebodies, Cleveland-Cliffs Iron Co. and McPhar Geophysics Ltd. undertook in 1953 to apply the inductive electromagnetic method to Cleveland-Cliffs properties in the Lake Superior region. As a result of this project, equipment has been developed that enables simultaneous transmission of two audio frequency waves, and the field technique and interpretative procedure involved have furthered exploration in the district significantly. Thus far, inductive electromagnetic application in the Lake Superior region has been only a development tool, that is, it is used to locate obscured contacts and faults as a part of property expansion and development. However, its application to primary reconnaissance of unexplored areas may be feasible in the future. The method has assisted in placing drillholes efficiently, and the elimination of excess drilling foot-ages and/or actual elimination of unnecessary holes has amply justified the expense of the geophysical survey. Cost of the field work involved is comparable on a per station basis to the cost of a magnetometer or superdip survey. Since observations require no reduction, i.e., are directly interpretable, overall expenditure is low, and the scope and detail of the survey can be adjusted in the field as geological- geophysical correlation becomes evident. To a great extent, this eliminates the second-guessing so commonly arising after office calculations are completed on data obtained with other types of geophysical surveys. This unique feature of field interpretation and its associated intimate feel of the project area, is, perhaps, one of the most valuable aspects of the inductive electromagnetic method as applied to iron ore exploration. Basis of Method Fundamentally, the method involves transmission of an alternating electromagnetic wave, of a chosen audio frequency, which permeates the ground materials in the vicinity of a transmitting, or primary, coil, see Fig. 1. This wave, or field, induces an electric current in any conductor on which it is incident. The flow of an alternating current in a conductor sets up its own, or secondary, radiating electromagnetic field. These two fields form a resultant whose configuration depends on the following characteristics of the subsurface conductors: 1) size, 2) shape, 3) electrical conductivity, 4) magnetic permeability, and 5) frequency of the transmitted wave. To a lesser extent the resultant is also dependent on material adjacent to the conductor, topography, and surface conductivity. For illustrative purposes, the primary, secondary, and resultant fields may be represented by vectors. In operation, the direction of the resultant vector is measured by a small receiving coil tuned to the frequency of the transmitted wave. Generally speaking, the method can be compared to the transmission and reception of the familiar radio broadcast, with special variations permitting measurement of the effect on reception of intervening materials. Field Technique Mechanics of field operation are simple. The mast is set up in a vertical position and is then guyed in place. The transmitting loop then is raised by means of a sheave at the top of the mast and the coil connected to the motor-generator. A special plane table is clamped into position on the mast and the loop is plumbed. The plane table is oriented according to a grid system established over the project area. By means of this plane table it is possible

Jan 1, 1956

By J. S. Browning

The U.S. Bureau of Mines has been experimenting with flotation processes to separate the spodumene-beryl ores mined at Kings Mountain, N.C. The success to date as well as the present status of the process is discussed. Further experimentation is underway and studies will be made on the milling costs involved in the flotation process. The pegmatites of the Kings Mountain-Lincoln ton, N.C., area constitute the largest known domestic reserve of beryl and spodumene. The reserve is estimated to contain 90 million tons of pegmatic material with 1,280,000 tons of recoverable Li,O(lithia) as spodurnene.' The pegmatites also contain 0.4 to 0.5 pct beryl disseminated throughout the orebodies. The pegmatites may contain a potential reserve of 240,-000 tons beryl, equivalent to approximately 34,000 tons of BeO. Different flotation methods for separating beryl from feldspar or quartz, or both, have been developed by various investigators.2-7 On the other hand, published information is limited on concentration of spodumene-beryl ores. As the response of beryl and spodumene to flotation is essentially the same, a successful separation of the two minerals depends upon use of a selective depressant or a selective collector for one of the minerals. Several years ago, the U.S. Bureau of Mines, recognizing the need for developing a large domestic supply of strategic beryl, undertook studies to develop improved methods of recovering this mineral. Because of the low beryl content of the pegmatites, economic production of the beryl entails its recovery as a byproduct of spodumene flotation. Thus, the development of procedures that would provide for maximum recoveries of the spodumene, as well as the beryl, was a primary objective of the studies. Tests were made on run-of-mine ore and spodumene flotation tailing from the Foote Mineral Co.'s spodumene concentrator at Kings Mountain (Fig. 1). Pet-rographic analyses of the ore and flotation tailing are given in Table I. Detailed analyses and examinations of the ore and tailings revealed that the beryllium was present in the form of a low-alkali beryl. The crystals were small, rarely larger than 14-mesh diam, and were clear and colorless. About 10 pct of the Li20 content of the ore was present in the mica and feldspar components of the pegmatite. In some weathered ores the associated clays also contained small amounts of lithia. This is typical of pegmatites in the Kings Mountain area. LABORATORY TESTS In the past, a vigorous chemical treatment of the spodumene surfaces with acid or caustic soda has been considered essential for satisfactory selective flotation of the spodumene from the other minerals in pegmatites. Many tests were made during this investigation to determine if chemical treatment of the spodumene could be eliminated in favor of a reagent combination that would depress the other minerals while selectively floating the spodumene. A simple reagent combination and process was developed that gave better spodumene recovery and grade of concentrate than the more elaborate acid or caustic treatment methods previously used. The finely ground ore pulps were conditioned with either an ammonium, alkali, or alkaline earth lignin sulfonate and sodium fluoride, and the spodumene was floated and cleaned using oleic acid as the collector. The spodumene tailing was deslimed, conditioned with sulfuric acid and coco amine acetate, and floated to reject mica. The mica tailing was thickened and conditioned with hydrofluoric acid, then washed to remove the acid. The washed pulp was conditioned with sodium hydroxide for pH control, and the beryl was floated and cleaned with oleic acid as the collector. Table II summarizes the results of the laboratory test work. About 77 pct of the spodumene and 75 pct of the beryl were recovered from the pegmatitic material. The spodumene concentrate assayed 6.1 pct Li20 and 0.01 pct BeO, and the beryl product assayed 3.0 pct Li20 and 1.57 pct BeO. Similar results were ob-

Jan 1, 1961

By Chi-shing Wang

The late Professor P. B. Bucky of Columbia University introduced the principles and techniques of barodynamic experimentation in early 1931 by the application of centrifugal loading to achieve dynamic similitude between models and prototypes of mine structures.1 Later, he and his associates introduced the combined experimental technique of photo- elasticity and the centrifuge to determine the stress distribution in civil engineering structures and mine workings by the use of transparent bakelite models.2,3 The photostress technique, also known as the birefringent-coating method of photoelastic stress analysis, dates back to 1930, when Mesnager published its principles.4 Since then it has been widely applied to experimental stress analyses in many industries. A practical method of observing the dynamic behavior of opaque mine models, which are made of prototype materials, by means of a combination of the centrifugal and the photostress techniques is a new experimental approach under development at the Henry Krumb School of Mines, Columbia University.5 This paper summarizes the development of the barodynamic photostress technique and presents the information obtained from a recent series of experiments in the study of the behavior of rock beams loaded by their own weight. THEORETICAL BACKGROUND Theory of Pure Bending In the general theory of strength of materials, the flexure stress at any point in a beam of any type of cross section which has a longitudinal

Jan 1, 1968

By John Chipman

DESPITE the rapidity of chemical reactions at steelmaking temperatures, deoxidation reactions cannot be expected to reach equilibrium immediately after addition of a deoxidizing agent. A considerable period of time may be required merely to obtain complete mixing of the deoxidizing element throughout the volume of steel to which it is added. Evidence in the literature indicates that in some cases the time is long compared with that allowed for completion of the experiment or for teeming of the heat. The great turbulence observed during the filling of the ladle is no guarantee of complete dispersion on a fine scale throughout the heat. During the process there are initially certain volume elements which are high in deoxidizer and others which retain substantially their original oxygen content. Mixing consists of the subdivision and ultimate destruction of these liquid segregates through the process of shear and elimination of concentration gradients by diffusion. The shear process does not continue indefinitely and a quiescent state may be reached in the ladle before all volume elements of divergent deoxidizer and oxygen content are completely eliminated. In furnace deoxidation the time required for complete mixing may be very long unless continuous stirring is employed.' In Fig. 1, let the circle represent one small volume element of aluminum-rich metal surrounded by oxygen-rich steel in which no stirring movement remains. Further mixing requires inward diffusion of oxygen and outward diffusion of aluminum, resulting in precipitation of A12O3 in the diffusion zone. It is important to note that such a precipitate may itself interfere with the diffusion process. Moreover, if the precipitate forms as a film with even minimal mechanical strength, it may interfere not only with diffusion but with shear as well, thus stabilizing compositional differences in volume elements of greater than microscopic size. A film surrounding such a volume element would have little or no ability to rise or to sink unless it enclosed a liquid whose density differed from that of the ambient. Consider now the effect on the overall composition of the melt. Fig. 2 represents the A1-O equilibrium at the temperature of the bath. High-aluminum elements of composition X may exist alongside high-oxygen elements of composition Y in such proportions that the average composition 2 has a much higher A1-O product than that corresponding to equilibrium. The A1-O product supposedly corresponding to equilibrium at 1600 °C was found by Wentrup and Hieber2 to be 10-10, by Hilty and crafts3 to be 2 X 10-9 and by Gokcen and chipman4 to be 2 x 10-14. Only the last named investigators approached equilibrium by means

Jan 1, 1962

By Wheeler P. Davey

When metals are subjected to mechanical working, such as rolling, one of the phenomena that take place is a movement of the crystals of the metal into a system or systems of orientation which bear an angular relation to the direction of working. In rolled metal the crystals may orient themselves with respect to the rolling plane or the rolling direction, or both. Direct evidence of the existence of preferred orientations in rolled metal has been obtained by numerous investigators from X-ray patterns of the rolled metal. Most of these workers used a monochromatic pinhole method. Where the degree of preference for a single orientation is high the monochromatic pinhole pattern may be interpreted by a geometrical calculation based on the angular relationships of the planes in the crystal and the diffraction arcs on the X-ray pattern. This process may be aided by the geometrical construction of the locus sphere (Lagenkugel), and reflection circles of Polanyi,l Polanyi and Weissenberg,2 and Mark and Weissenberg,3 and of the plane polar figures (flachenpolfigur) of Franz Wever.4 R. M. Bozorth5 solves X-ray patterns from metals having a single preferred orientation by means of a series of charts which when placed over the X-ray pattern give directly certain angular relationships, between the crystal planes and the surface of the specimen.

Jan 1, 1930

By John Chipman

RECENT developments in iron alloys containing nitrogen have indi-cated that this element may exert a considerable influence on the proper-ties of the metal. This influence is not always in an undesirable direction and the indications are that nitrogen should be regarded as an alloying element, the amount of which should be subject to control, rather than as an inherently deleterious impurity. In controlling this element in liquid iron to the best advantage, it is necessary to have a reliable background of fundamental data pertaining to solubilities, rates of solution and chemical reactions of nitrogen in liquid iron. Obviously, the first step in such an investigation is the determination of the solubility of nitrogen in pure iron, and this has been the object of the experiments described in this paper. The solubility of nitrogen in solid iron has been measured by Jurich,1 Sieverts,2 Martin,3 and Iwasé4 and the agreement among the first three inspires confidence in their results. No accurate determinations of its solubility in liquid iron have been recorded though several investigators have obtained approximate results. Strauss5 was able to introduce 0.03 to 0.04 per cent nitrogen into steel by the action of either ammonia or nitrogen on the liquid metal. This was accomplished by Eilender and

Jan 1, 1935

By Fritz Wald, Richard W. Stormont

lHE general constitution of a number of metal-lead telluride and metal-tin telluride systems has recently been studied in an effort designed to furnish background information for the study of degradation mechanisms on junctions between thermoelectric power generation materials and metals.1"4 This paper reports further results of that effort. It was found that cobalt-lead telluride constitutes a stable pseudobinary section through the ternary Co-Pb-Te system. Materials used in the study were lead and tellurium of semiconductor-grade purity (American Smelting and Refining Corp., 99.999+ pet). Cobalt (Johnson Matthey & Co., 99.999 pet purity) was used in the form of slices cut from rods of 5 mm diam. Twenty- gram charges of the alloys were melted in evacuated quartz ampoules. Thermal analysis, as described previously,2'3 and metallographic and X-ray diffraction methods (Debye-Scherrer photographs) were used as investigative tools. Substantial difficulties were encountered in polishing, as reported previously for the lead telluride-iron system.3 A number of different etches were used, including dilute aqua regia, Murakami solution, an etch containing copper nitrate,3 and HC1-HNO3-acetic acid-water mixtures. None of these etches gave consistent results over the complete range of cobalt concentrations. On the alloys containing bulk cobalt in the form of primary

Jan 1, 1969

By E. P. Jennings

The iron-ore deposits of Iron county, Utah, which rival those of Lake Superior in extent, are situated 275 miles south of Salt Lake City, and 25 miles south of Lund, a station on the San Pedro, Los Angeles & Salt Lake railroad. The range of hills containing the deposits has a general NE-SW. strike, and rise from a few hundred to 2,000 ft. above the Escalante desert, the ore being included in an area of 5 by 20 miles. The basal rock of these hills is diorite-porphyry. The flanks of the range are covered with limestone supposed to be of Carboniferous age, underlain in some localities by quartzite. Both formations are conformable to the porphyry, and are the remnants of beds that formerly covered the highest peaks, but have been removed subsequently by erosion. In the central and southern parts of the range, beds of Cretaceous sandstone rest unconformably on the eruptives. Rhyolite-flows occur to the south and southeast of the iron-ore deposits; and dikes and sheets of post-Tertiary lava are common. With the exception of a few springs, the range is destitute of water. Sage-brush, stunted cedars and the common desert-bushes constitute the only vegetation. Large beds of coal of poor quality occur in Cretaceous sandstones 15 miles east of the ore-deposits.

Jan 1, 1905

By Colin Rae

THE absence of paraffin and other oil hydrocarbons in the soil, although they are concentrated in extensive deposits in some localities, the common distribution of plant remains through many formations that .are not productive for oil, and many other factors, seem to indicate the existence of an intermediate organic compound between the complex plant compounds and the petroleum hydrocarbons; and much evidence points to the humus acids or associated organic compounds, which are probably collected by surface waters and concentrated in certain areas by means of precipitation by electrolytes, which would be contained in sea water or possibly in various inland seas or lakes. PRESENT-DAY EVIDENCE There are many present-day evidences of the association of petroleum with humus acids. Binney, in 1912, made observations without explanations on the peat mosses of Down Holland, England, where he found petroleum being formed by decomposition, in the presence of an infiltration of sea water. The analysis of a typical peat will show its relationship to the humus acids under consideration. SAMPLE 'No. 1, SAMPLE NO. 2, PER CENT. PER CENT. Water : 20.0 29.5 Ash 3.0 3.05 Fiber 47.0 54.95 Humus acids 30:0 12.50 J. D. Haseman and others have noted the association of asphalt and hydrocarbons with the swampy, boggy areas, particularly adjacent to the sea.

Jan 2, 1922

By T. Sterry Hunt

In a paper presented to the Institute in 1881* I have discussed at some length the question of the " Hydrometallurgy of Copper," and among others, have noticed two methods, devised and patented by Mr. James Douglas and myself, for the extraction of copper

Jan 1, 1888

By E. N. Smith, J. C. Redmond

The increasing need for materials capable of withstanding higher operating temperatures for various applications such as gas turbine blading and other parts, rocket nozzles, and many industrial applications, has brought consideration of cemented carbide compositions. The well known usefulness of cemented carbides as tool materials is attributable to their ability to retain their strength and hardness at much higher temperatures than even complex alloys. However, it has been found that the temperatures encountered in cutting operations do not approach by several hundred degrees1 those involved in the applications mentioned above where the interest is in materials possessing strength and resistance to oxidation at temperatures of 1800°F and above. At these latter temperatures, the tool type compositions which are made up essentially of tungsten carbide are found to oxidize very rapidly and to produce oxidation products of a character which offer no protection to the remaining body. As a further consideration, the density of the tungsten carbide type compositions is high, from about 8.0 to 15.0. The refractory metal carbides as a class are the highest melting materials known as shown by Table 1 which summarizes the available data from the literature for the carbides of the elements which are sufficiently available for consideration for these uses. The density is also included in the table, since as mentioned above it is an important consideration in many of the applications for which the materials would be considered. It has been established that in the tool compositions the mechanism of sintering with cobalt is such as to result in a continuous carbide skeleton and that the properties of the sintered composition are thus essen- tially those of the carbide.2 On the hypothesis that this mechanism holds to a greater or less degree in cementing most of the refractory metal carbides with an auxiliary metal, it appears from Table 1 that titanium carbide compositions would offer possibilities for a high temperature material. Titanium carbide has extensive use for supplementing the properties of tungsten carbide in tool compositions. Although the literature contains several references to compositions containing only titanium carbide with an auxiliary metal,3,4,5,6 it may be inferred from the meager data that such compositions were deficient in strength and were considered to have poor oxidation resistance.7 Kieffer, for instance, reports the transverse rupture strength of a hot pressed TiC composition at 100,000 psi as compared to up to 350,000 psi for WC compositions. The work described herein was undertaken to determine the properties of compositions consisting of titanium carbide and an auxiliary metal and to improve the oxidation resistance of such compositions. It appeared possible that the inclusion of one or more other carbides with titanium carbide might improve the oxidation resistance and also that this might be more desirable than other means from the point of view of maintaining the highest possible softening point. Consideration of the available carbides in Table 1 suggests tantalum and columbium carbides because of their high melting points and general refractoriness. The work on improving oxidation resistance was concentrated on the addition of tantalum carbide or mixtures of tantalum and columbium carbide. The auxiliary metals used included cobalt, nickel and iron. It was also desired to learn the general physical properties of these compositions. Experimental Procedure The compositions used in this study were made by the usual powder metallurgy procedure applicable to cemented tungsten carbide compositions. The powdered carbide or carbides and auxiliary metal were milled together out of contact with air. In some cases cemented tungsten carbide balls and in other instances steel balls were used to eliminate any effect of tungsten carbide contamination. A temporary binder, paraffin, was then included in the mix and slugs or ingots were pressed with care to obtain as uniform pressing as possible. The ingots were presintered and the various shapes of test specimens were formed by machining, making the proper allowance for shrinkage during sintering. Thereafter the shapes were sintered in vacuum at temperatures of from 2800 to 3500°F. Final grinding to size was carried out by diamond wheels under coolant. The titanium carbide used contained a minimum of 19.50 pet total carbon and a total of 0.50 pet metallic impurities as indicated by chemical and spectrographic analysis. It was found by X ray diffraction examination with

Jan 1, 1950