Search Documents

By J. F. Wilkinson

A high degree of accuracy is often required in mine-surveying, in order that expensive mining work may not be misdirected. The making of underground connections by drifts or shafts located as the result of surveys presents a crucial test of correctness not usually involved in any other class of surveying. In view of these considerations, the present notes and description of a survey made in June, 1890, for the San Francisco shaft of the New Almaden quicksilver-mines, may be of interest to members of the Institute who are surveyors. The purpose of this survey was to locate on the surface a vertical 2-compartment shaft (3.5 by 7 ft.), to connect with another vertical shaft, of practically the same size, which had been sunk a number of years before from an adit-level about 240 ft. vertically below the surface, to a deeper, so-called 600-ft. level. It will be seen, of course, that the most important matter was to secure an exact coincidence in vertical line, so that the resulting continuous vertical shaft from the surface should have no offset or irregularity at the point of junction between its two parts. The levels were of less importance; but, as the hoisting-works were to be placed in position and the new shaft permanently timbered from the start, its correct alignment was an essential requirement. The important features of the work, therefore, were the methods used in determining with certainty : 1. That the shaft was located in the right place in a general way; 2. That the ordinary inaccuracies of linear and angular measurements were so reduced as to insure correctness of location within certain defined and allowable limits. Instruments.—Thc instruments used were: a Buff and Berger transit-theodolite, with a 6-in. horizontal plate, reading to 10 seconds; a Heller and Brightly Y-level; a Chestermán steel tape, graduated in tenths and hundredths of a foot; and New York leveling-rods, graduated to thousandths of a foot.

Jan 1, 1901

By F. V. Lenel

R. P. Seelig.*—Dr. Lenel is to be congratulated on his presentation of a particularly interesting paper describing the use of the powder metallurgy process for the production of magnetic pole pieces. The only thing that might be added is that we have been successful in producing pole . pieces with a narrow hysteresis curve by the use of considerably lower sintering temperatures than the ones used by Dr. Lenel. It is quite possible that this use of lowe- temperatures has considerably widened the field of commercial application for pole pieces made from metal powders. Development work is currently being done on an a.c. application of a sintered iron part. However, I am in full agreement with Dr. Lenel that if eddy currents are an important factor in the application, we cannot substitute sintered material for laminated sheet-metal structures. Mr. Peters' remarks concerning the limitations of machine parts were well taken. The emphasis of the limitations makes it easier to define clearly what we can do and-what the advantages are of machine parts made of metal powders. When I mention metal-powder machine parts, I mean those of relatively high density, although complete elimination of porosity is not possible at this time. The limitations of the field for this type of parts are largely economical. I believe that Mr. Langhammer has made that point very clear. The following questions are very often asked: How large a part can you make? How close can you hold the dimensions ? How fast can a part be produced? In a majority of the cases, it depends on the cost at which the part can be produced. A large variety of shapes and sizes of a number of materials can be formed. However, the main requirement in this field of endeavor is whether this can be done more economically by powder metallurgy than by other manufacturing methods. As a general indication, it may be stated that densities up to 95 per cent of that of rolled material can now be produced commercially in simpler parts. Tolerances of plus or minus 0.001 in. are common, but where special conditions justify, closer tolerances can be held; we are producing a part of which one dimension is held to 0.0003 inch. Finally, as far as maximum size is concerned, technically this would depend on the capacity of the press and furnace equipment available. Actually, we find that the economical limit of powder-metallurgy machine parts is approximately one pound. From there on, each individual case must he studied on its own merits.

Jan 1, 1945

By Robert Mehl

RELATIVELY few data have been collected on the rates of diffusion in ternary solid solution systems. In general it does not seem worth while to gather extensive data for such systems until the factors that determine the rates of diffusion in binary systems are better understood. But the rates of diffusion in a ternary system of limited solid solubility, in which the terminal solid solution is in equilibrium with an intermediate phase and may thus be represented as a quasibinary system, represents a case of special interest. In this case, where by reason of the association of the two solute metals in an intermediate phase a special attraction of the two solute atoms may be safely assumed, some interaction of these atoms during simultaneous diffusion in the solvent lattice might be expected. It has frequently been proposed that molecular solid solutions exist in quasibinary and in other ternary (and binary) solid solutions. There is no direct evidence for such solid solutions; arguments based upon the supposed anomaly in certain physical properties1 are hardly important; unexpected density relationships have proved deceptive ;2 suggestions of molecular solid solutions have been made on the basis of solution laws in their application to certain systems, but without result;3 attempts to find lattice parameters in the solid solution Al-MgZn2, which cannot be calculated from the separate effects of magnesium and zinc and might therefore be taken as evidence for a molecular aggregation, have given negative results.4 Fundamentally, methods for the determination of the state of molecu¬lar aggregation in solution depend upon the kinetic behavior of the par-ticles constituting the system. If it could be shown that the two solutes in a quasibinary ternary system diffuse in molecular proportions, despite a radical difference in the separate rates of diffusion of each solute when diffusing alone in the solvent lattice, some basis for the concept of molecu-lar solid solution would be afforded. Freche5 examined the rates of independent and simultaneous diffusion of magnesium and silicon in

Jan 1, 1939

By J. J. Reed

The mines of southeast Missouri's Lead Belt have been in operation since 1864, almost 100 years. During this period about 10 pct of the total ore available has been left in place as pillars, and this now represents the best ore reserve left to the older mines. St. Joseph Lead Co. has been investigating various plans of pillar recovery for several years. The example to be described is only one possible approach under a specific set of conditions. Conditions vary greatly in the different areas within the Lead Belt, and the same approach would be entirely inadequate in certain other areas, but there are important sections where this system is clearly applicable. Horizon mining is practiced in the Lead Belt, and stopes may vary from 10 ft to well over 100 ft high. Fig. 1 is a plan view of 6100 stope, the area to be discussed. For these mines this is a small stope, only 10 to 12 ft high. Before any plans were drawn up for pillar recovery, three independent estimates of the pillar grades were made by the mine superintendent, the mine captain, and the mine geologist. After these results were averaged, pillars indicated to be of economic grade were marked for removal as shown. At this stage several alternatives were considered: 1) retreat with caving, 2) concrete replacement pillars, and 3) systematic bolting and retreat. A retreating system with caving was not chosen because the roof was known to be too bad even to permit loading a blasted pillar before caving would begin. Concrete replacement pillars would have been too costly and would have required a large crew, bulky materials, and unwieldy equipment. Systematic bolting was chosen as being most acceptable for the following reasons: 1) Limited area and spans were involved. 2) Only minor modifications to the jumbo would be required for bolting. 3) Only a two-man bolting crew would be needed. 4) Only compact bolting materials would be required. 5) The bolting plan could be modified to allow

Jan 1, 1960

By G. S. Brooks, L. G. Duncan

During the past few years, the Mineral Point Zinc Co. has had under consideration the improvement of various types of gas-filtering apparatus used in the removal of dust from crushing and milling plants, in the manufacture of oxide, and on blast-furnace fume and sintering furnaces. The original equipment of the various plants of the company was, of course, along lines of the standard stationary bag house. These houses required large surfaces, hand shaking, and varied only in the manner of the collection of solids and in the distribution of the gas. , Early in 1908, the first trial of a mechanical bag house was made at Nassau Plant at Depue, Ill. The duty of this installation was on dust-laden gas from a fine-crushing mill. The Printz and Rau bag machine was finally adopted and put into operation. This ingenious machine embodied what were then to us two novel features in bag-house practice: 1. An intermittent crinkling and snapping of the filtering fabric to free the meshes of solids. 2. A reversal of gas flow for a short period by a temporary connection with the suction trunk. This equipment worked fairly well except in cold weather, when we ran into condensation troubles. Had we at that time understood more fully some of the limitations of fabric filtering work, these might well have been remedied. We were impressed by this experience, however, with the efficiency of sudden tension on the fabric under suction. After a study had been made of some of the western blast-furnace houses using the reversal-of-flow feature, experiments were started early in 3 914 with a view to developing an automatic equipment along the best lines of our past experience. The objects sought were: 1. Keeping labor out of the houses for hygienic reasons. 2. Reduction of labor costs. 3. Reduction in size of bag houses. 4. Accessibility. 5. Ability to handle relatively hot gases where required.

Jan 1, 1918

By A. M. Gaudin, D. W. Fuerstenau

By streaming potential techniques, the zeta potential of quartz has been measured as a function of the concentration of dodecylammonium salts at different pH values. These experiments indicate that adsorption of dodecylammonium ions takes place as individual aminium ions until a certain critical concentration is reached in the double layer, at which point the adsorbed collector ions begin to associate into patches of ions, called hemi-micelles. Because of its effect on the surface potential of quartz, pH controls the adsorption of dodecylammonium ions. The value of cooperating agents and nonionized constituents of flotation systems is discussed. A PREVIOUS investigation' of the role of pH in the flotation of quartz with anionic collectors is here extended to an inquiry of how the cationic collector, dodecylammonium acetate, is adsorbed at the quartz-solution interface. The equilibrium amount of this collector adsorbed by quartz has already been measured as a function of concentration and pH.2,3 The weight of prior evidence has suggested that two mechanisms are involved in the adsorption of this collector by quartz, but with existing adsorption measurements alone it is not possible to determine what the mechanisms are. Gaudin and Bloecher2 postulated that a polymolec-ular adsorption coating begins to form before the first monolayer has been completed. Gaudin and Morrow4 indicated that a similar situation might exist in the film of dodecylammonium ions on hematite. A study of electrokinetic potentials at the quartz-solution interface provides some detail toward a fuller understanding of the adsorption mechanism. Experimental Results The zeta potential at the quartz-solution interface was calculated from streaming potential data measured with the apparatus described in detail in a thesis by Fuerstenau5 and briefly in a paper by Gaudin and Fuerstenau.1 The quartz used in these experiments was a 48/65-mesh fraction prepared in the manner described previously.' Zeta potential of quartz was obtained for various amounts of the amine salt at pH 4, 7, 10, 11. In

Jan 1, 1956

By N. Jaffe, J. E. Dorn

The effect of stress on the creep rate of high-purity poly crystalline aluminum in the intermediate temperature range was investigated by conducting creep tests at a series of different stresses and by decreasing the stress abruptly during the course of primary and secondary creep. Three series of decreases in stress tests were conducted: the stress was decreased in primary and secondary regions of creep at 347.5°K and the stress was decrensed in primary creep at 327°K. The results demonstrate the effects of structure and temperature on the stress dependence of the creep rate. The trends in the creep rate after a drop in stress are complicated and show that recovery takes place. The experimental results were compared with Friedel's theory for cross-slip, the experimentally determined energy for a constriction being in good agreement with the theoretical estimate proposed by Stroh. PREVIOUS investigations have shown that the ap-- parent activation energy for creep of polycrystalline aluminum, over the range from about 250° to 380°K, is approximately 27,400 cal per mole,' a value that is to a first approximation insensitive to the applied stress, the creep rate, and the creep strain. Several facts strongly support the thesis that creep, in this temperature range, is controlled by the rate-determining mechanism of cross-slip: 1) Recovery of the cold-worked state can take place by a number of mechanisms prominent among which is climb and cross-slip. Astrom2 reported rapid recovery of cold-worked polycrystalline aluminum at 340° to 370°K giving an activation energy of 28,000 cal per mole and additional recovery at the higher temperatures of 455° to 478°K giving an activation energy of 36,000 cal per mole. Whereas the latter process was clearly identified with the climb mechanism, the former process. which has an activation energy in good agreement for that of creep in the same temperature range, is most likely due to recovery by thermally-activated cross-slip. 2) Single crystals of aluminum exhibit sharp slip-

Jan 1, 1962

By R. C. Hassinger, D. V. von Rosenberg

Transverse dispersion has received considerably less treatment in the literature than has longitudinal dispersion. Different methods for determining transverse dispersion coefficients have been used in different investigations, and the results obtained have not been consistent enough to permit accurate generalizations as to the effect of various physical parameters on the magnitude of these coefficients. A numerical solution to the differential equation describing transverse dispersion in the absence of longitudinal dispersion was obtained to enable one to calculate the dispersion coefficient from experimental results. The more general dispersion equation including longitudinal dispersion also was solved numerically to give quantitative limits of a dimensionless group within which the assumption of negligible longitudinal dispersion is justified. Possible experimental procedures were examined, and one utilizing a cylindrical packed column was chosen for the determination of transverse dispersion coefficients. Values of these coefficients were determined for a system of two miscible organic fluids of equal density and viscosity, for two sizes of packing material over a wide range of flow rates in the laminar regime. The dispersion coefficient was found to decrease, for a constant value of the product of packing size and interstitial velocity, as the size of the packing material particles increased. INTRODUCTION Longitudinal dispersion has received extensive treatment in the literature, and consequently is better understood than its orthogonal counterpart, transverse dispersion. Many mathematical models of dispersion processes assume that transverse dispersion is rapid enough to damp out any radial** concentration gradients and therefore may be neglected. Laboratory and production results, however, indicate that this is a poor assumption.l,2 Various experimental procedures for determining transverse dispersion coefficients have been used in previous investigations, but the results have generally been expressed by similar correlations. The transverse dispersion coefficients obtained, however, have often varied considerably for given values of the correlation parameters. We feel that further experimental determinations of transverse dispersion coefficients will help alleviate some of the inconsistencies in these empirical correlations. One assumption implicit in all previous investigations is that of negligible longitudinal dispersion in the experimental system. An attempt to justify this assumption often is made using intuitive reasoning, but it is apparent that this reasoning must break down as the condition of zero flow rate is approached. A mathematical examination of the equations describing the system yields physical limits outside of which the assumption of negligible longitudinal dispersion is invalid. BACKGROUND In a porous medium, the "effective molecular diffusivity" De is less than the molecular diffusivity D measured in the absence of a porous medium, due to the tortuous path which a diffusing molecule must travel. Various authors3-5 have reported values of the ratio De/D in the range of 0.6 to 0.7. When there is fluid flow within the porous medium, mass transfer occurs by convective dispersion as well as by molecular diffusion. These are separate phenomena and can be treated as such on a microscopic scale. However, the mathematical complexity is such that only extremely simple geometries could be considered, and the results hardly would be applicable to the complex geometries existent in actual porous media. A more

Jan 1, 1969

By Charles H. Jacoby, Stanley J. LeFond

Salt, or halite, has a long and most varied history. While we know the Chinese were producing salt as early as 3000 B.C., the first written reference to salt appears in the book of Job recorded about 2250 B.C., which reads: "Can nothing which is unsavory be eaten without salt?" We do not know when man first used or realized that he needed salt. Perhaps one of our early Eolithic ancestors noted a piece of salt shining along the shore of a salt lake or a bay. He may have been attracted by its shining luster and tasted it. He found that it had a tart, zesty, distinctive flavor and perhaps chewing a large piece, became ill. However, by experimentation he soon learned that taken in the proper proportions salt was a very pleasant additive to his food. He may have noticed, too, that it increased his feeling of well-being. Thus, when the curtain of recorded history rises, we find man using salt for his health's sake, seasoning his food with it, feeding it to his animals, and using it in many superstitious and religious ceremonies. These uses, however, are a far cry from the uses for salt today. The first attempts of white man to make salt in continental United States were reported in the year 1614, while the first commercial production was in 1753 from the Kanawha licks. Practically all this salt was for human consumption, preserving food, and curing hides. Prior to the coming of the white man, Indians are known to have made salt from salt springs such as those that existed at Avery Island, LA, Charleston, WV, Saltville, VA, and Onondaga, NY. In 1862 the first rock salt was mined in the US from the Avery Island salt dome. Almost immediately thereafter, rock salt was mined at Saltville, VA and then at Retsof, NY in 1885. Of the more than 39 million tons produced annually in the United States, about 58% or 23 million tons are consumed by the chemical industry in the production of chlorine, caustic soda, hydrochloric acid, sodium metal, and some 30 other basic chemicals. These basic chemicals, in turn, are used in the preparation of approximately 14,000 chemicals which range from soap and detergents, to such chlorinated hydrocarbons as DDT, BHC, carbon tetrachloride, etc. Utilization of cavities created in salt beds and domes has grown rapidly since 1947 until now the waste salt is creating an ecological problem. The uses for both dry- and solution-mined cavities range from the storage of liquid hydrocarbons to containerized storage of toxic wastes, from compressed air for the peak shaving of power to storage of nuclear wastes. Geology Mineralogy Properties: Because of its simple structure, halite, the mineralogical name for salt, was the first structure to be analyzed by X-rays. It has the following properties: Formula: NaCl (Na-39.34%. Cl2-60.66% ) Crystallography: isometric, hexoctahedral, 4/m 32/m Space group: Fm3m A0: 5.627 kX Cell contents: Na4CI4 Habit: usually cubic, rarely octahedral, massive, granular to compact Physical properties: Refractive index: 1.554 Twinning: observed on {111} Cleavage: {001} perfect Fracture: conchoidal, brittle

Jan 1, 1983

By B. M. Larsen, K. Heindlhofer

THIS paper describes a relatively simple electrical apparatus that, through the close analogy between the flow of heat and of electricity, enables one to solve quickly and with satisfactory accuracy many complex problems in heat flow. This device, developed in 1935, has proved especially useful in the solution of certain practical problems relating to the design and efficiency of regenerators for an open-hearth furnace or coke oven, yielding within a few hours information that would take weeks or even months to acquire by mathematical1.2 or experimental3 methods of comparable accuracy. Its description now is prompted by growing interest in such analogues, as shown by several recent papers.4.5 The analogy between flow of heat and of electricity appears to have been recognized first by Maxwell who, in his famous Treatise on Electricity and Magnetism (1881) says: The analogy between the theory of the conduction of electricity and that of the conduction of heat is at first sight almost complete. If we can take two systems geometrically similar, and such that the conductivity. for heat at any part of the first is proportional to the conductivity for electricity at-the corresponding part of the second, and if we also make the temperature of any part of the first proportional to the electric potential at the corresponding point of the second, then the flow of heat across any area of the first will be proportional to the flow of electricity across the corresponding area of the second. .. Thus, in the illustration we have given, in which flow of electricity corresponds to flow of heat, the electric potential to temperature, electricity tends to flow from places of high to places of low potential, exactly as heat tends to flow from places of high to places of low. temperature He noted, however, that this analogy is restricted: ... there is, however, one remarkable difference between the phenomena of electricity and those of heat. Suspend a conducting body within a closed conducting vessel by a silk thread, and charge the vessel with electricity. The potential of the vessel and of all within it will be instantly raised, but however long and however powerfully the vessel be electrified, and whether the body within be allowed to come in contact with the vessel, or not, no signs of electrification will appear within the vessel, nor will the body within show any electrical effect when taken out. But if the vessel is raised to a high temperature, the body within will rise to the same temperature, but only after a considerable time, and if it is then taken out it will be found hot, and will remain so till it has continued to emit heat for some time. The difference between the phenomena consists in the fact that bodies are capable of absorbing and emitting heat, whereas they have no corresponding property with respect to electricity. According to this statement the application of the analogy would be limited to problems of steady flow that do not involve heat-capacity effects. In spite of this

Jan 1, 1945

By I. R. Kramer

[The final paper in the diffusion symposium was given by I. R. Kramer. The author called attention to the diffusion characteristics of chromium deposited on the surface of steel by treatment with chromium chloride and alloyed with the surface layer of the steel by thermal treatment. As the data cited were previously published in the paper " Chromizing of Steel," by I. R. Kramer and Robert H. Hafner (Metals Technology, October 1942, and in the Transactions, volume 154, 1943, pages 415-420), it is unnecessary to reproduce these data here. The following paragraphs are taken from the author's presentation.— Editor.] Aside from the well-known practical application of the diffusion phenomena to carburizing and calorizing, -diffusion also finds application in adding alloying elements to the surfaces of steel parts. The chromizing of steels is a process by which the surface of a low-alloy steel may be enriched with chromium to form a highly corrosion-resistant case; This chromized case differs from an electroplated coat in that it is a diffused layer integral with the base metal and has all of the properties of a high-chromium steel. Recently a method of chromizing has been developed in Germany by Daeves, Becker and Steinberg in which gaseous chromium chloride and hydrogen are passed over the steel at temperatures of 1650° to 1800°F. The chromium chloride reacts with the iron to give chromium and iron chloride. The chromium atoms are deposited on the surface and diffuse in as the iron atoms diffuse out, forming a layer rich in chromium. The principal role of hydrogen is to remove the carbon from. the surface of the steel. Of the two mechanisms, chemical reaction and diffusion, the one operating at the slower rate will determine the rate of formation of the layer. In this case, diffusion is slower and therefore any factors influencing its rate will affect the process. The rate of diffusion is influenced by the temperature and crystal structure of the parent metal. Depth-concentration studies show that the concentration falls off gradually for a considerable distance and then drops sharply at about 13 per cent chromium, the point coincident with the boundary of the gamma loop. The influence of the composition of the base metal upon diffusion is quite important. The depth of penetration of the chromium decreases as the carbon content increases and, of more importance, the chromized layer becomes brittle and is likely to spa11 if the carbon content is too high. It appears that in order to chromize successfully the carbon must be fixed by strong carbide-forming elements such as chromium or molybdenum, which decrease the diffusion of carbon. If this is not done, the carbon will diffuse from the interior faster than the chromium can diffuse inward, thus forming a carbide barrier. The corrosion resistance of the chromized layer is high, and these steels offer some unique advantages over other corrosion-resisting coating or alloys. While chromizing is not meant to replace stainless steels, it may serve in the saving of alloying elements. The chromizing process uses soft or low alloyed steels that can be easily hot or cold formed and since the chromized layer is soft and firmly adherent, chromized parts can be subjected to cold deformation without spalling or chipping and without loss of corrosion resistance.

Jan 1, 1944

By I. R. Kramer

[The final paper in the diffusion symposium was given by I. R. Kramer. The author called attention to the diffusion characteristics of chromium deposited on the surface of steel by treatment with chromium chloride and alloyed with the surface layer of the steel by thermal treatment. As the data cited were previously published in the paper " Chromizing of Steel," by I. R. Kramer and Robert H. Hafner (Metals Technology, October 1942, and in the Transactions, volume 154, 1943, pages 415-420), it is unnecessary to reproduce these data here. The following paragraphs are taken from the author's presentation.— Editor.] Aside from the well-known practical application of the diffusion phenomena to carburizing and calorizing, -diffusion also finds application in adding alloying elements to the surfaces of steel parts. The chromizing of steels is a process by which the surface of a low-alloy steel may be enriched with chromium to form a highly corrosion-resistant case; This chromized case differs from an electroplated coat in that it is a diffused layer integral with the base metal and has all of the properties of a high-chromium steel. Recently a method of chromizing has been developed in Germany by Daeves, Becker and Steinberg in which gaseous chromium chloride and hydrogen are passed over the steel at temperatures of 1650° to 1800°F. The chromium chloride reacts with the iron to give chromium and iron chloride. The chromium atoms are deposited on the surface and diffuse in as the iron atoms diffuse out, forming a layer rich in chromium. The principal role of hydrogen is to remove the carbon from. the surface of the steel. Of the two mechanisms, chemical reaction and diffusion, the one operating at the slower rate will determine the rate of formation of the layer. In this case, diffusion is slower and therefore any factors influencing its rate will affect the process. The rate of diffusion is influenced by the temperature and crystal structure of the parent metal. Depth-concentration studies show that the concentration falls off gradually for a considerable distance and then drops sharply at about 13 per cent chromium, the point coincident with the boundary of the gamma loop. The influence of the composition of the base metal upon diffusion is quite important. The depth of penetration of the chromium decreases as the carbon content increases and, of more importance, the chromized layer becomes brittle and is likely to spa11 if the carbon content is too high. It appears that in order to chromize successfully the carbon must be fixed by strong carbide-forming elements such as chromium or molybdenum, which decrease the diffusion of carbon. If this is not done, the carbon will diffuse from the interior faster than the chromium can diffuse inward, thus forming a carbide barrier. The corrosion resistance of the chromized layer is high, and these steels offer some unique advantages over other corrosion-resisting coating or alloys. While chromizing is not meant to replace stainless steels, it may serve in the saving of alloying elements. The chromizing process uses soft or low alloyed steels that can be easily hot or cold formed and since the chromized layer is soft and firmly adherent, chromized parts can be subjected to cold deformation without spalling or chipping and without loss of corrosion resistance.

Jan 1, 1944

By Kenneth M. Ritchie

Mineral wool is a term applied to man-made fibers of silicate glass with useful properties resulting from their fibrous nature. In contrast with crystalline fibrous minerals such as asbestos, mineral wool fibers are amorphous, solid filaments produced by drawing from molten liquid and subsequent cooling. Chemically they are silicate glass with varying percentages of metallic oxides, especially those of aluminum, calcium, magnesium, iron, and in glass wool, sodium, potassium and boron. Other elements such as manganese, titanium, sulfur, etc., result from their presence in the raw materials used and are not purposely added. In the United States, mineral wool is a generic term and may be applied to rock, slag or glass wool. In Europe, glass silk and silicate cotton are products in the same category, but the term mineral wool is less commonly used. Current usage is to ignore the actual source and to differentiate products on a composition basis; thus rock and slag wools have about 35-45 pct of silica, while glass wool has 54 to 60 pct. Much mineral wool of slag origin is called "rock wool," and this practice is increasing, although wool made of slag from lead or copper refining is often referred to as "lead slag wool." Its greenish-gray to greenish-black dark color, due to 5-25 pct Fe (reported as FeO), distinguishes it from "white" wools made from iron, blast furnace slag containing only 1-2 pct FeO or Fe203. Most mineral wool is used for thermal insulation against heat and cold; sound absorption and isolation are probably the next most important uses. Both its thermal and acoustic values result primarily from the physical structure of the heterogeneous mixture of fibers and air which is the form in which the fibers are first obtained and handled. For this reason, within fairly wide limits, differences in chemical composition are relatively unimportant, and for most conventional applications all types are competitive in properties and value. Mineral wool intended for extreme conditions of high temperature, acid resistance and special purposes must have a chemical composition which will insure the desired properties. This may differ greatly from that of ordinary wools; for example one product approximately 98 pct Si02 and another consisting of 50 pct A1203 and 50 pct Si02 are produced and sold for high temperature service up to 2000°F or more. These are considerably more expensive to manufacture and their cost limits their use. Historical The manufacture of mineral wool consists fundamentally of a process which subjects molten material to shear and/or tensile forces that draw them into fibers. The liquids are cooled at a rate which solidifies them quickly. As a solid glass they are technically super-cooled liquids since they have no true melting point. The drawing out of glass into thin rods, filaments and tubes was known from very early times, and present day continuous production of glass filament for textiles was evolved gradually by adapting hand methods to automatic machinery. Rock and slag wool manufacture had a somewhat different development. Early explorers reported finding filamentous material

Jan 1, 1960

By S. K. Sarkar, B. Dr. Singh

INTRODUCTION India like USA has traditionally relied on bord and pillars as dominant underground method. Coal has generally been mined at shallow depth from relatively thick and horizontally bedded coal seams. These' factors contributed towards large scale adoption of bard and pillar. After nationalisation of coal industry in two stages in 1971 and 1973, large scale mechanisation and modernisation programmes were undertaken. Longwall mining was identified as one of the major that area for increasing underground coal production. The idea to introduce longwall mining was mooted to increase productivity and to promote conservation and safety. The nationalised coal industry has already worked about twenty longwall faces with different types of support. The tempo of introducing longwall is catching up and a number of longwall programmes with, Self advancing supports of different types and Capacity are in active stage of implementation. The country has not yet started producing mechanised Supports and therefore supports and machineries are being imported from U.K. and other countries of the continent. The of the major problem faced in the longwall projects is to choose suitable type and capacity of supports. The suppliers and manufacturers of these supports are not competent enough to choose and offer the right type and capacity of supports as their knowledge and information about Indian strata conditions are extremely limited. The Central Wining Research Station (Q.!RS), has undertaken a research programme for evaluating the rock mechanical conditions obtaining in the proposed longwall locales and has worked out a method for selection of proper type and capacity of supports on the basis of projected strata behaviour at the proposed locale. STRATA CCNTROL FAILURES Indian coal industry had made some attempts to introduce longwall caving in the early fifties after a working group set up by the Government of India had recommended its adoption to increase productivity and to modernise mines. Approximately 20 longwall faces were tried in the major Indian coalfields of Jharia, Ranigunj and Karanpurr between 1951 and 1968. The supports used consisted of 20T hydraulic props or 35140~ friction props. A number of these faces had suffered total strata control failures and a large number of support elements were lost. The Central Mining Research Station initiated a research programme to analyse these failures in the general background of behaviour of Indian coal measure strata at longwall faces. All the available data regarding the cases of failures were collected and physico-mechanical properties of overlying roof rocks were determined in the laboratory. Simultaneously, observations were continued to establish the behviour pattern of Indian coal measure strata at longwall faces. These studies were helpful in analysing the occurrences of collapse. BEHAVIOUR OF INDIAN COAL MEASURE STRATA The coal measure strata encountered in the principal Indian coalfields of Jharia, Ranigunj and Karanpura are in general strong in nature however, the immediate roof (mostly up to 1.5 to 2 m) in most of the cases is weak and false bedded shale. MI idea about the strength properties of immediate and overlying roofs may be obtained from the following table.

Jan 1, 1982

By M. C. Leverett, S. E. Buckley

The production of oil is accomplished as a result of its displacement from the reservoir by either gas or water, and the amount of oil recovery is limited by the extent to which the displacing gas or water accumulates. This paper describes the mechanism by which the displacement is effected and the advantages of water over gas as a displacing agent. In the light of the results of experimental observations of the flow of mixtures of oil and/or gas and/or water through sands, certain conclusions are drawn relative to the changing character of the displacement as depletion proceeds, and on the effects of the properties of the fluids and of producing conditions on the ultimate oil recovery. Introduction Crude oil has no inherent ability to expel itself from the pores of the reservoir rocks in which it is found; rather, it must be forcibly ejected or displaced by the accumulation of other fluids. Accordingly, a knowledge of the mechanism by which one fluid is displaced by another is essential to an understanding of the fundamental process by which oil is recovered. The displacing fluids normally available are gas and water, either or both of which may exist originally associated with the oil in a potentially usable form or may be supplied to the reservoir from external sources. Gas is present in most oil reservoirs. If the quantity is relatively small, it may exist originally completely dissolved in the oil, but if the quantity exceeds that which may be held in solution by the oil at the prevailing pressure, the excess will be found in the free state. Most reservoir sands appear to contain some water,l and in the majority of fields the oil is trapped in the structure and held over water. In certain conditions the entrapping water may advance into the oil zone and displace the oil therefrom. This paper describes in a qualitative manner some of the characteristics of the displacement of oil by either gas or water, with an attempt to elucidate somewhat the mechanism by which such displacement is effected. Role of Dissolved Gas When the pressure on an oil containing dissolved gas is reduced to the saturation or bubble-point pressure, gas escapes from solution and expands, imparting to the oil-gas mixture a high degree of expansibility and causing it to flow in the direction of reduced pressure. This expansibility has frequently been attributed to the oil; closer analysis, however, reveals that as gas escapes from solution the oil phase actually. contracts. Hence, it is the accumulation and expansion of the liberated gas that supplies the propelling force for the oil. It has been shown experimentally2-5 that within certain limits a sand containing oil, gas and water will permit the simultaneous flow of all three; the readiness with which they may flow depends upon the characteristics of the sand, of each of the fluids, and upon the relative amounts of the fluids in the sand. Thus, in the initial stages of production by the mechanism of dissolved gas drive, the liberated gas is present in the sand in low concentration and is unable to

Jan 1, 1942

By S. E. Buckley, M. C. Leverett

The production of oil is accomplished as a result of its displacement from the reservoir by either gas or water, and the amount of oil recovery is limited by the extent to which the displacing gas or water accumulates. This paper describes the mechanism by which the displacement is effected and the advantages of water over gas as a displacing agent. In the light of the results of experimental observations of the flow of mixtures of oil and/or gas and/or water through sands, certain conclusions are drawn relative to the changing character of the displacement as depletion proceeds, and on the effects of the properties of the fluids and of producing conditions on the ultimate oil recovery. Introduction Crude oil has no inherent ability to expel itself from the pores of the reservoir rocks in which it is found; rather, it must be forcibly ejected or displaced by the accumulation of other fluids. Accordingly, a knowledge of the mechanism by which one fluid is displaced by another is essential to an understanding of the fundamental process by which oil is recovered. The displacing fluids normally available are gas and water, either or both of which may exist originally associated with the oil in a potentially usable form or may be supplied to the reservoir from external sources. Gas is present in most oil reservoirs. If the quantity is relatively small, it may exist originally completely dissolved in the oil, but if the quantity exceeds that which may be held in solution by the oil at the prevailing pressure, the excess will be found in the free state. Most reservoir sands appear to contain some water,l and in the majority of fields the oil is trapped in the structure and held over water. In certain conditions the entrapping water may advance into the oil zone and displace the oil therefrom. This paper describes in a qualitative manner some of the characteristics of the displacement of oil by either gas or water, with an attempt to elucidate somewhat the mechanism by which such displacement is effected. Role of Dissolved Gas When the pressure on an oil containing dissolved gas is reduced to the saturation or bubble-point pressure, gas escapes from solution and expands, imparting to the oil-gas mixture a high degree of expansibility and causing it to flow in the direction of reduced pressure. This expansibility has frequently been attributed to the oil; closer analysis, however, reveals that as gas escapes from solution the oil phase actually. contracts. Hence, it is the accumulation and expansion of the liberated gas that supplies the propelling force for the oil. It has been shown experimentally2-5 that within certain limits a sand containing oil, gas and water will permit the simultaneous flow of all three; the readiness with which they may flow depends upon the characteristics of the sand, of each of the fluids, and upon the relative amounts of the fluids in the sand. Thus, in the initial stages of production by the mechanism of dissolved gas drive, the liberated gas is present in the sand in low concentration and is unable to

Jan 1, 1942

By J. D. Doherty

A. R. POWELL*—Mr. Doherty has outlined in a most thorough manner valid arguments for the development of an industry in this country making syn. thetic liquid fuels from coal. No thoughtful person will dispute the statement that it is essential to carry on fundamental and applied research and acquire engineering "know-how" by the erection and operation of two or three large plants in the near future. Considerations of national security indicate that this should be done, irrespective of any temporary present surplus of natural petroleum. It is the belief of the discusser and of many others interested in coal technology that our energy picture of the future will include an increasing utilization of coal directly, without any conversion to liquid fuel, as a source of energy. A fact that is sometimes forgotten is that petroleum fuels have often been cheaper than coal in many locations and over long periods of time, and this price factor has been of great importance in expanding the use of petroleum fuels at the expense of coal. Synthetic liquid fuel made from coal must necessarily be several times as costly as the coal from which it is made, and this fact alone will have a profound effect on the future energy pattern of our country. This complete change in the economic relationship between solid and liquid fuels will lead to the substitution of coal itself for many uses now supplied by the relatively cheap petroleum fuels. From the standpoint of conservation of our natural resources, the substitution of coal itself for liquid fuels wherever possible when the age of synthetic liquid fuel arrives is also logical. At least 50 pct of the energy of coal is lost during conversion to liquid fuel. Nor is this com-pensated for by a higher utilization effi-ciency of the liquid fuel in most cases. For example, modern steam-boiler plants can operate at equal fuel efficiencies with either coal or fuel oil.

Jan 1, 1950

By AIME AIME

TUESDAY afternoon the annual meeting was devoted to a general session, in the auditorium, on production control. George Otis Smith presided and in opening the meeting recalled that the session in 1920 on the stabilization of the coal industry was the first time this subject had been discussed by Institute members in a general session and then introduced Carl Snyder, of the Federal Reserve Bank of New York, who spoke on "Long-time Growth and the Factors In Its Variations." He spoke without notes and a full presentation of his views must be deferred until the stenographer's report is available. He said that of the total production some 80 to 90 per cent represents goods for consumption and the other 20 to 10 per cent for construction. He discussed various indices of production, concluding that bank clearings are the best, and showed by charts that when they are plotted, allowing for various disturbing factors, they are seen to increase quite regularly at the rate of about 4 per cent per year. The production curve rises at only 3y2 per cent per year, because agricultural production does not in- crease as fast as manufacturing postal revenues in- crease at the rate of 5 per cent per year while the use of electricity increases twice as fast.

Jan 1, 1929

By L. B. Gittinger

Sulfur is a nonmetallic element widely distributed in nature. It constitutes 0.06% of the earth's crust but only a very small portion occurs in sufficiently concentrated amounts to justify mining. Sulfur occurs in practically all animal and plant life. It constitutes approximately 0.09% of the elements in the oceans; it has been found in meteorites. Sulfur was known and used by man before recorded history. The American Chemical Society approved spelling for the element is sulfur. The English spelling sulphur is used commercially in the United States. In ancient times, sulfur was called brimstone, literally "burning stone." Today the term brimstone is used interchangeably with the term elemental sulfur. Sulfur is found naturally in the elemental form in subsurface deposits associated with gypsum and anhydrite in salt domes and sedimentary formations in evaporite basins and in solfatara-type deposits associated with volcanoes and mineral springs. Sulfur occurs also in molecular combination in ferrous sulfides (pyrites and pyrrhotite) and nonferrous sulfides (copper, lead, zinc, and nickel), and in mineral sulfates (gypsum and anhydrite); as hydrogen sulfide contaminant in natural gas; as organic compounds in crude oil and tar sands; and as pyrite and organic compounds in coal and oil shales. Sulfur resources are abundant and exist throughout the world but the extent to which they can be classified as reserves is greatly circumscribed by prevailing prices and technology. Estimates of world sulfur reserves are compiled by the U.S. Bureau of Mines. A compilation of reserves by area and source of sulfur published in 1970 and presented here as [Table 1] totaled 2.47 billion tons (Lewis, 1970). The effect of the decline in prices which has occurred since the earlier estimate is dramatically illustrated by the 1972 estimate of the U.S. Dept. of the Interior which shows world sulfur reserves of only 1.2 billion tons (Anon., 1972d). Sulfur is produced commercially from one or more sources in nearly 70 countries of the world. World production of sulfur in all forms totaled 41.6 million tons in 1971. (Sulfur statistics given in this chapter are long tons.) Native deposits, sulfides and oil and gas contributed, respectively, 31, 41, and 25% of world production (Table 2). Of the sulfur produced from native deposits, salt domes accounted for 54% and evaporite basin deposits, 44%. Volcanic deposits are of little significance except for local consumption. The past two decades have seen important shifts in the world's sulfur sources. In 1950, native deposits and sulfides each supplied about one-half of the world's production. During the 1950s, sulfur recovered from oil and natural gas grew rapidly, representing about 10% of the total by 1960. Since then, the petroleum industry has continued to increase its relative importance as a source of sulfur, representing more than 30% at 1972 year-end. Sulfur is generally classified as elemental or nonelemental for statistical purposes. Elemental sulfur is sulfur produced in the pure, uncombined form. It includes production from native deposits, as well as that recovered in the elemental form from oil and natural gas or other sulfur-bearing materials. When produced from other than native deposits, it is generally referred to as recovered elemental sulfur. Nonelemental sulfur is that which is utilized commercially in molecular combination with other elements, such as sulfides or sulfates. Elemental sulfur is being produced from salt dome deposits in the Gulf Coast region of the United States and the Isthmus of Tehuantepec in Mexico, and from evaporite basin deposits in west Texas, Poland, Sicily,

Jan 1, 1975

By John C. Calhoun, J. E. Warren

A study of waterflood efficiency, given in terms of oil recovery at water breakthrough and u1timate recovery, has been made on short, consolidated Pyrex glass cores rendered oil-wet by chemical treatment. Contact angle. interfacial tension, permeability and porosity were the variables considered. Oil and water viscosities, core length and velocity of flooding were held constant. The data permit interfacial tension, contact angle, porosity, and permeability to be grouped into a scaling coefficient along with viscosity, velocity of flooding and length of core. Correlation of the .scaling coefficient with recovery at water breeakthrough is found to follow prediction; correlations of ultimate recovery demand a scaling coefficient different from that which correlates breakthrough recovery. The work indicates that, with proper control, a group of similar natural cores, of permeability plug size, call he correlated 10 indicate basic flooding performance. INTRODUCTION The fraction of oil recovered from a porous medium is related to both reservoir conditions and production techniques. An investigation of all factors that enter into this relationship is necessary in order to arrive at the optimum method of exploitation for oil reservoirs. To define this relationship, laboratory studies have been made by a great many investigators. However. an important obstacle arises if the results of these experiments on water flooding are to be applied to practice. Ditferences in behavior are to be expected between reservoirs of the dimensions encountered underground and those used in laboratory work. Factors which play an important role under laboratory conditions may be of no consequence in reservoirs. Laboratory operating practices generally differ from field operating practices. Thus. a mere understanding of the mechanism of the displacement of oil by water is not enough. It is just as necessary that the process be analyzed dimensionally to give continuity and validity to the conversion from laboratory to field. The theory of oil displacement that has come to be accepted by the majority of those who are associated with reservoir mechanics had its beginning in the work of Leverett¹ and Buckley and Leverett2. The banking of oil, observed by many previous workers, was described by the "fractional flow" and the "frontal advance'' equations. The validity of the Buckley-Leverett theory was substantiated by the experimental and theoretical work of Terwilliger et al³; moroever, the theory was extended by the introduction of the idea of a "stabilized zone" to describe the banking of oil. Levine5 showed that the Buckley-Leverett equations gave reasonable agreement between calculated and experimental breakthrough recoveries only if the capillary pressure and gravity terms were included. Rapoport and Leas1 investigated the properties of linear floods and showed that both breakthrough and maximum recovery are related to a "scaling coefficient'' derived from the Buckley-Leverctt equations. Jones-Par-ra and Calhoun6 presented another scaling coefficient which included both viscous and capillary variables. Such scaling coefficients should suffice to predicl waterflood efficiency. However, some experimenters report data which does not appear consistent with the healing coefficient approach. For example, Engelberts and Klinkenberg7 conducted an extensive series of experiments on a dimensional model which contained a

Jan 1, 1956