Search Documents

By Alden B. Greninger, Alexander R. Troiano

Metallurgists have long believed that martensite in steel forms as plates along the octahedral {111} planes of austenite. Much has been written about mechanisms whereby units of the austenite lattice are pictured as transforming to martensite by shearing movements initiated along the octahedral planes of austenite, supposedly resulting in plates of martensite lying parallel to these planes of shear. A critical inspection of two or three photomicrographs of quenched hypereutectoid steel led us to the conclusion that the orientation habit of martensite, at least in hypereutectoid austenite, could not possibly be octahedral. Inasmuch as recent studies,30,31 of the martensite-type reaction in nonferrous alloy systems have established the irrational orientation habit as characteristic of this type of lattice transformation, the need for a thorough restudy of the crystallography of martensite formation in steel was evident. The present paper reports the results of such a study, extended to include both cementite and some of the products of constant-temperature decomposition of austenite. Also reported are a few of the results obtained from a microscopic and X-ray study of the austempering process in very high-carbon steel. I. The Martensite Transformation Previous Work Microstructure and Crystal Structure of Martensite.—Among the best series of published photomicrographs of quenched steels are those of Whitely,1 Robertson,2 Hanemann and Schrader,3 and Lucas.4 The crystal structure of martensite is body-centered tetragonal, with axial ratio varying from 1 near 0.0 per cent carbon to 1.08 for 1.75 per cent

Jan 1, 1940

By W. D. Donnelly, M. L. Rudee

THE crystallography and morphology of ?-Al3Fe precipitates in an A1 + 0.5 wt pct Fe alloy have been studied by transmission electron microscopy. The alloy was cast in cylindrical ingots, 15 cm in diameter and 60 cm in length, and cooled slowly. The measured composition was 0.527 wt pct Fe, 0.001 wt pct Mg, and 0.003 wt pct Cu. Spectrographic analysis revealed no additional trace impurities. Thin slices were cut from the ingot and reduced by more than 95 pct by rolling to a thickness of 0.1 mm with no intermediate annealing treatments. These thin sheets were then vacuum-annealed for 1 hr at 612°C and air-cooled in their capsules. Thin foils for examination in the electron microscope were prepared by electropolishing. The precipitate is found in the form of oval platelets on the (110) planes of the matrix. The major axes of the platelets are parallel to the (110) directions of the matrix, and vary in length from 1/2 to 2 p. The thickness is about 1/10 µ. Examples of platelets, both in the plane of the foil and normal to the foil, are shown in Figs. l(a) and l(b), respectively. lack' found that ?-A13Fe (more correctly Al13Fe4) belongs to the monoclinic system. Using Black's structural data and simultaneous electron-diffraction patterns from the matrix and precipitates, the habit planes and directions were determined to be: (001)? 1 (110)Al [100]?|| H [001]Al The orthogonal crystallographic axes of the precipitates are accurately in the habit plane, while the measured coincidences of the directions are only within 10 deg. The major axis of the platelet is parallel to [010] in the 0. This orientation corresponds to the direction of nearest registry of the lattices.

Jan 1, 1964

By Eugene Jablonski

Statistical data on the Polish producing business are available only for the first half of 1939. Because of the invasion of the country during September by Germany and Russia all sources of information have stopped, and it is impossible to get even an approximate picture of the status of the industry after that date. The long declining trend of Polish production, which was finally checked during 1938, kept a further upward tendency during the first half of 1939, and there is good reason to believe that the upward trend would have been maintained. It is true, there was little hope of reviving the slowly dying Boryslaw field, although there still remained a slight possibility for an extension in its southwestern direction. Repressuring plans were still discussed, but. could not be put into effect because of extremely complicated and split-up lease ownership. The Gorlice-Lipinki ficld continued to be the main factor in the increase of the country's production. During the first half of 1939 this field received a further important extension in a southern direction. The Schodnica field continued to use repressuring with success. At the end of June, 21 exploratory wells were drilling, 14 of which were within thc Carpathians and 7 in the Miocene geosyncline of the Carpathian Foreland. All of the wildcat wells drilled within the Carpathians were on the struct,ural cxtcnsion of old established fields, but part of the wildcats of the Foreland were on new geological and geophysical prospects. The Opary gas field of the Foreland discovered last year has been further developed. The Government-owned Polmin completed its third gasser. This well penetrated two sands; the upper one, 118 ft. thick, was found at 1312 ft., with an initial pressure of 570 lb. and capable of produeiring 10 million cu. ft. per day. The second sand, 91 ft. thick, was found at 1690 ft., yielding 20 million cu. ft., with a pressure of 760 lb. The well Mieczyslaw, drilled about 3 miles further north on the flank of the structurc, found the first sand watered. The Pioneer No. 5, at Chodonice near Przemysl, which reported somc gas last year, was 5696 ft. deep at the end of June, still drilling in Miocene. Anothe well in the same vicinity drilled by the Gasolina was 1708ft. deep.

Jan 1, 1940

By Eugene Jablonski

Statistical data on the Polish producing business are available only for the first half of 1939. Because of the invasion of the country during September by Germany and Russia all sources of information have stopped, and it is impossible to get even an approximate picture of the status of the industry after that date. The long declining trend of Polish production, which was finally checked during 1938, kept a further upward tendency during the first half of 1939, and there is good reason to believe that the upward trend would have been maintained. It is true, there was little hope of reviving the slowly dying Boryslaw field, although there still remained a slight possibility for an extension in its southwestern direction. Repressuring plans were still discussed, but. could not be put into effect because of extremely complicated and split-up lease ownership. The Gorlice-Lipinki ficld continued to be the main factor in the increase of the country's production. During the first half of 1939 this field received a further important extension in a southern direction. The Schodnica field continued to use repressuring with success. At the end of June, 21 exploratory wells were drilling, 14 of which were within thc Carpathians and 7 in the Miocene geosyncline of the Carpathian Foreland. All of the wildcat wells drilled within the Carpathians were on the struct,ural cxtcnsion of old established fields, but part of the wildcats of the Foreland were on new geological and geophysical prospects. The Opary gas field of the Foreland discovered last year has been further developed. The Government-owned Polmin completed its third gasser. This well penetrated two sands; the upper one, 118 ft. thick, was found at 1312 ft., with an initial pressure of 570 lb. and capable of produeiring 10 million cu. ft. per day. The second sand, 91 ft. thick, was found at 1690 ft., yielding 20 million cu. ft., with a pressure of 760 lb. The well Mieczyslaw, drilled about 3 miles further north on the flank of the structurc, found the first sand watered. The Pioneer No. 5, at Chodonice near Przemysl, which reported somc gas last year, was 5696 ft. deep at the end of June, still drilling in Miocene. Anothe well in the same vicinity drilled by the Gasolina was 1708ft. deep.

Jan 1, 1940

By John W. Vanderwilt

THE fluorescence of scheelite has been an important aid in recent years in the discovery and development of scheelite deposits. The use of fluorescence of synthetic compounds in industry, particularly in advertising, also has expanded greatly during the past decade. As a result, a number of new and convenient units for producing ultraviolet energy have become available, which have led to a greater application of fluorescence in the study of minerals. Studies have shown that the fluorescent color of a mineral may vary: (I) with the kind and quantity of trace elements, and (2) with the particular wave length of ultraviolet energy used. The wave length is dependent first on the type of generating equipment used, and finally on the filter employed to remove the visible light that may be present. A number of so-called ultraviolet lamps are listed and described, together with suitable filters known to be available. Scheelite fluoresces brilliantly with wave lengths of 2200 to about 3000Å., but not with longer wave lengths. The most convenient and efficient sources of ultraviolet for scheelite fluorescence- are portable and laboratory units designed particularly for use with scheelite. So-called ultraviolet light globes of the photo-flood type emit wave lengths too long to cause scheelite to fluoresce. Attention is called to the minerals that fluoresce in a manner similar to scheelite, which necessitates a check test by means of characteristic physical properties. Chemical tests are the final authority both for identity and content of tungsten in scheelite ore.

Jan 1, 1946

By R. A. Deju, R. B. Bhappu

The theory of electrophoresis is briefly outlined and an apparatus which may be used for electrophoretic studies is explained. The results obtained using this apparatus are in agreement with those obtained by other investigators. How to solve some of the complications which occur in the measurement of zero charge and zeta potential is explained. It is believed that the apparatus described in this paper will allow rapid measurements of zeta potential, zero point of charge, electrophoretic mobility and zeta coefficient. For many years the phenomenon of electrophoresis has been studied, and much work has been done in designing an apparatus for better measurements of mobility, zeta potential and zero charge of minerals. Up to the present, most electrophoresis experiments have involved cumbersome equipment and tedious microscopic observation. The modified cell proposed in this paper obviates these drawbacks by using a Rayoscope together with a special system of lenses and filters. It therefore allows a faster and more accurate measurement of zero charge and particle velocity. THEORY Most authors currently regard zeta potential as the potential difference in an otherwise uniform medium between a point some large distance from the surface of the mineral and a point on the plane of shear. Fuerstenau,1 Miaw,2 and Gaudin and sun3 have performed some calculations of zeta potential using Henry's equation.4 Their results show wide discrepancies, probably due to differences in the past histories of the minerals used. The authors have also noticed this difference on determining the zero point of charge of quartz as shown on Table I.

Jan 1, 1967

By W. R. Wawersik, A. M. Starfield

The classical approach to room-and-pillar mine design in flat-lying, tabular ore bodies limits itself to the special case of an extensive and uniform system of pillars. Each pillar is then assumed to carry the same load, and this load is readily calculated from the extraction ratio e and the weight of the overburden : average pillar stress = [ ] where H is depth below surface, p is average density of overburden, and g is acceleration due to gravity. The average pillar load does not, in this case, depend on the mechanical properties of either the pillars or the surrounding rock mass. The only relevant physical property of the pillars is their compressive strength, (i.e., the maximum load-carrying ability) and the criterion for design is that the average pillar stress should not exceed this strength. The wider the pillar, the greater its strength, and the design of the system is concerned with reconciling this increase in strength to the requirements of roof control so as to optimize extraction.l Any departure from a uniform distribution of pillar loads invalidates the classical approach. Such departures may, for instance, be brought about by: (1) a nonuniform layout of pillars and remnants resulting from selective mining, (2) variations in geology which result in gross changes in the properties of part of the seam or the host rock, (3) deliberate use of abutment support in narrow panels, and (4) the use of yielding pillars for local roof support in conjunction with barrier pillars to carry the overburden load.

Jan 1, 1972

By Albert F. J. Bordeaux

This paper briefly describes the general outline of cyaniding silver-ores in Mexico, with special reference to personal experiments made in the Temascaltepec district. The most important papers on the subject deal with cyaniding gold-silver ores, the gold predominating in value, so that the treatment is nearly the same as for gold-ores, the losses of silver being considered of little importance. I describe here the treatment of silver-gold ores containing very little gold, which is more general in Mexico than elsewhere. The cyanide treatment, which was so successfully applied to gold-ores, did not succeed immediately with silver-ores on account of their varying composition. Gold occurs in nature usually in the native state, while silver occurs generally in combination with sulphur (argentite), and various combinations of sulphur, antimony, and arsenic. In former times there mas a complete difference in the treatment of gold-ores and silver-ores. Amalgamation, which was successful with gold-ores, was generally inadequate with silver-ores. The usual treatment in Mexico for silver was the patio process, the theory of which was satisfactorily explained only quite recently by Mr. Ortega and others. General Outline of the Cyanide Treatment. The general tendency of the present practice is to slime the silver-ore as much as possible, and in order to obtain a higher efficiency, with less loss of cyanide, and greater speed, the following lines are observed: 1. Crushing by stamps with 30- or 40-mesh screens, then crushing by Huntington or Chilean mills, through 60- or 80-mesh screens. 2. Concentration upon vanners.

Jan 1, 1910

By Bahngrell W. Brown

IN an age when anything short of miraculous can and does happen it is entirely too easy to become labeled as a prophet. After the first wave of hysteria over atomic weapons died down there were crystal gazers enough in that field. The mining fraternity, always anxious to get back to normal anyway, looked, was duly impressed, and passed on to more mundane affairs. After all it was just another big blast in the stopes of life. After we "laymen" had seen the effects at Hiroshima and been granted a peek into the phenomenon of Numbers 4 and 5, we saw, indeed, that it was a tremendous but understandable weapon. Now it appears that we may fall heir to much of the defensive planning of the future. If, as our military planners tell us, it will be necessary to go underground for defense, then we are the true forerunners of a race of troglodytes. The underground belongs to us as to no other profession; the subsurface is our prerogative. Already the big mistakes in planning atomic defense are being made. It is within our ability now to correct them. Surveys are being made of natural caverns to be used as a basis for military planning. This is our first big mistake. Even if the natural caverns, many of which Nature has precariously carved from cherty and brittle limestones, could withstand the seismic force of a proximate blast without major roof failures, there is a more serious argument against the blanket use of natural caverns as a first line of defense. In addi-

Jan 1, 1946

By E. S. Tankins

The main purpose of this work was to study the effect of gold on the activity coefficient of oxygen in the liquid Fe-Au alloy and to determine how copper and silver change the activity coefficient of oxygen. A preliminary investigation has been made of equilibrium in the reaction of hydrogen with oxygen in some of the liquid gold alloys. The experimental method, which has been described in detail elsewhere,' consisted of bubbling accurately known H-A-water vapor mixtures through the Fe-Au alloys contained in alumina crucibles within a vertical closed furnace. When equilibrium was reached, the samples were quenched by rapidly lowering the crucible under an atmosphere of argon to a water cooled brass fixture at the bottom of the furnace tube. The melts were found to freeze from the top in less than 4 sec. The heats were carefully prepared for oxygen analysis. The oxygen content was determined by vacuum fusion analysis.' Only high purity electrolytic materials were used in this investigation. The activity and free energy of oxygen in the liquid iron alloys were studied by means of the reaction; The data for the 80 Fe-Au alloys, obtained as a function of temperature, are summarized in Table I and presented in Fig. 1, where log is plotted against . The results can be expressed by: The data were obtained using water vapor-hydrogen ratios between 0.04 and 0.30, and a 25 pct H2-75 pct A mixture. An oxygen content between 0.030 and 0.060

Jan 1, 1970

By Raimo Matikainen

Sublevel stoping has been used in Finland since the 1930's and today more than ten under- ground mines have adopted it as their main stoping method (Fig. I). Approximately 80% of the total underground tonnage is mined by sub- level stoping (Table 1) The first mines to introduce the sublevel stoping method in Finland were limestone mines. The development of sublevel stoping was very slow up to the mid 1960's when the switch to trackless mining started and the increase of mechanization lead to higher capacity and productivity. The method itself has been almost the same since the 1950's when long hole drilling was introduced. According to a future prognosis sublevel caving will give way to sub- level stoping; on the other hand, open pit mining will at the same time grow rapidly with some new mineral orebodies, which will he brought into production. Most Finnish orebodies are, however, only marginal ores and they could not support mining with more expensive methods than open pit mining or sublevel stoping. The future of sublevel stoping seems relatively bright. GEOLOGICAL AND ROCK MECHANICAL BACKGROUND The rock mechanical conditions in Finland are in general relatively good and the rocks firm. The compressive strength is normally 40 - 150 Mpa and modulus of elasticity 40 - 200 Gpa. Low values are common in altered and fractured rocks and near the ore contact Rock stress measurements have been carried out already for 20 years for mine design and monitoring purposes. The results of these measurements show that relatively high horizontal stresses seem to be common (Fig. 2).

Jan 1, 1981

By R. H. Johnson

The Manual of the Oil and Gas Industry, under the Revenue Act of 1918, published by the Treasury Department for the guidance of oil companies in preparing their estimates of future recoverable oil for the purpose of calculating depletion, gives the first large public collection of comparative decline curves for the whole country. It is a matter of both scientific and practical interest to so arrange these data that the pools can be readily compared. There are certain difficulties in such a comparison, however: (1) The economic limit varies from 50 to 2000 bbl. a year in different pools taken. (2) Because of this variation in economic limit, the range of data shown makes comparison possible only for wells of intermediate size. In order to be as inclusive as possible, I have taken as an expression of the rate of decline the amount of oil produced in the period during which a well drops from 3000 to 2000 bbl. a year. No period of smaller production could be used because of the high economic limit in California; and no period of larger production and yet include the small well areas of the Appalachian. As it is, the Lima-Indiana wells are excluded. In a few instances, curves were extrapolated to obtain the reading, where the curve seemed regular enough to warrant it. In general, the amount of oil, in barrels, produced while a well declined from 3000 bbl. to 2000 bbl. a year is shown in Table 1.

Jan 1, 1921

By Francis A. Thomson

But little has been written concerning the camp of Republic. In 1900 Chatard and Whitehead 1 reported the results of some experiments with samples of ore from the Republic mine, and a few years later Fritz Cirkel2 described the construction, operation, and results attained in the mill at the Mountain Lion mine. From time to time brief articles, mostly of a semi-technical nature, have appeared in the Engineering and Mining Journal and other mining periodicals. The general geology of the camp, especially in regard.to its areal features, has recently been ably described by Joseph B. Umpleby.3 To bring to mind the general features of the district it may perhaps be well to review briefly some facts in regard to it, before discussing the treatment of the ore. I. History and Production. The town of Republic is situated in the NW. corner of Ferry county, about 25 miles south of the International Boundary, on the head-waters of the San Poi1 river, in what was formerly the " north-half" of the Colville Indian reservation. On Washington's birthday, 1896, this portion of the reservation was thrown open to mineral location, and within a few weeks important discoveries had been made. The present Eureka mining-district was organized, the camp grew apace, and consignments of ore were shipped by wagon to Grand Forks, 30 miles away; or to Marcus, a somewhat greater distance. It is reported that the first 1,500 tons shipped from the Republic mine uetted the owners $160 per ton, after being hauled

Jan 1, 1913

By J. T. Shimmin

THE past twenty-five years has been a period of unparalleled improvement in all lines of mining and metallurgical equipment, but probably none has undergone greater refinement and development than the vacuum filter. Beginning a quarter of a century ago, there has been steady advancement in the art of vacu-um filtration until today its use has become virtually standard practice for dewatering throughout the entire metallurgical industry as well as in important parts of the chemical and industrial processing fields. The credit for the first successful application of vacuum filtration 'at the Consolidated Mercury mines in Utah in 1902 undoubtedly belongs to George Moore. There, it is said, his filter reduced the loss of gold in the slime and sand from $1.25 to 40c. per ton. Successful applications were subsequently made by Mr. Moore at the Liberty Bell mines, Telluride, Colo., the Lundberg, Dorr &Wilson mill at Terry, S. D., and elsewhere. E. L. Oliver is generally credited with, having done the most to work out the necessary continuity of op-eration exemplified in the well-known continuous vacu-um filter which bears his name. Others made improve-ments also, but in my opinion all the new ideas advanced in recent years are modifications of the fundamental principles originated by the two pioneers, Moore and Oliver. Considerable interest has been shown recently in the new type of continuous internal-type vacuum filter which is associated with my own name1. In response to frequent inquiries regarding it and the steps which led up to its invention, I am giving herewith a brief account of the early history of this development and some of the more important installations which have been made during the last year or so. A. M. Nicholas (now deceased), an Australian engi-neer, conceived the idea, several years ago, of manu-facturing a continuous vacuum filter with the filter medium applied upon the inside of the drum, as con-trasted with existing drum filters in which the medium is applied externally. Nicholas recognized that a ma-chine of this type would be simpler than one with a tank and would overcome some of the difficulties en-countered with tank filters on certain classes of pulps, and he appreciated the value of having filtration take place in the same direction as the gravitational settle-ment of the solid particles in the pulp, the pulp being retained within the drum instead of being held against the outside surface. The ease of starting up after a shut down was likewise realized by Nicholas. It was tried in the United States, but was not entirely success-ful primarily due to mechanical defects.

Jan 5, 1928

THE Institute of Metals Division of the American Institute of Mining and Metallurgical Engineers appointed a Research Committee in 1925 to de-termine what could be done by the Division to promote research work in the United States on non-ferrous metals. It was recognized that a considerable volume of use-ful research work in this field was being carried on by individual industrial companies as well as by the uni-versities and other research institutions, such as the Bureau of Standards. One need only refer to the recent research literature on non-ferrous metals in the TRANS-ACTIONS of the A.I.M.E., and elsewhere, to be con-vinced of healthful research activity in this field. The appointment of the Committee, however, voiced the impression that what was being done was, however excellent, inadequate for the needs of the industry. It was felt that the Division could usefully devote some of its time and effort in stimulating activity in this field. The deliberations of the Research Committee have not failed to develop wide differences of opinion even on the simple questions: (1) whether the Division can aid in any practical manner in this cause and (2) what the features of such aid might be. However, it was clear that there was only one type of research activity with which it could be very usefully concerned, viz., that on subjects of fundamental interest and general application. It was obvious that research work having special objects and more immediate commercial appli-cation should best be left to the industry itself.

Jan 1, 1927

Mining headlines in 1952 dealt mainly with expansion as the industry aimed for an ever increasing production to meet the nation's needs. Huge sums were expended for equipment, research, and development. Headlines told part of the story. Negotiations between San Manuel Copper Co. and the RFC finally resolved in a $94 million loan for the development of low grade Arizona ores. Magma Copper, parent firm was to supply an additional 8 million. Kennecott Copper Co., deepening its Deep Ruth Shaft of its Ruth, Neyy mine, announced that the shaft would be in full production in 1953.

Jan 2, 1953

By L. O. Howard

THE practice of using acid-lined converters at the plant of the Old Dominion Copper Mining & Smelting Co. was discontinued early in January, 1913, and they were replaced by basic-lined converters. The new equipment consists of one electrically operated 12-ft. upright converter stand and two basic-lined shells for same. These shells are provided with twenty-four 1 1/4-in. tuyères. The mouths are 5 ft. in diameter. Owing to the fact that there is no bedding system or other large storage capacity between the mine and the smelter, the furnaces must handle as fast as produced ore and concentrates, which may vary considerably from day to day, both in tonnage and copper content. Consequently the converter is often crowded to its utmost capacity by the frequent fluctuations in the daily matte supply. From the foregoing, it will be seen that in no way can the converter be favored by running light charges or by transferring to it from other stands in operation. Neither can it regularly be allowed to cool between blows, and only occasionally can it be run at as low a temperature as might be wished. No copper precipitate or other foreign material high in copper is available to help out the tonnage. Repairs and alterations or the removal of defective tuyères must wait until such time as a slight falling off in the matte supply-allows the converting operations to ease up. These variable conditions all combine to interfere with the systematic operating of the converter.

Jan 7, 1914

By H. H. Kellogg

An invitation to address you on the occasion of the one-hundredth anniversary of AIME represents an honor, a challenge and an opportunity: an honor that you judge me worthy; a challenge that I present to you a picture of extractive metallurgy in the years ahead that contains some ideas of value; and finally, an opportunity for me to express some deeply felt beliefs about our profession and our industry. My topic concerns the technology of metal production in the future - the processes, new and old, that will be used to extract metals. The nature of these processes will be shaped by many forces - some technical, some economic, some political or social. A forecast of future technology must recognize the role of each of these forces, and I have endeavored to do this in the analysis that follows. In brief, my outline consists of an analysis of the forces (perhaps better called "problems") that will influence the future of our industry, followed by consideration of likely lines of technological development to meet them. Let me dwell for a moment on the nature of this industry and the profession that serves it. I have been engaged in the profession of extractive metallurgy - teaching, researching and consulting - for 30 years. I have always found the subject stimulating and rife with challenges of a scientific, engineering, economic and socio-political nature. It is a big subject - it encompasses most of the elements of periodic table; we measure the U. S. production of six metals in millions of tons per year; new plant costs range to $100 million and more. The supply of metals from our extractive plants plays an essential role in our modern industrial economy. We could do without DDT, or phosphate detergents or 300-page Sunday newspapers; we cannot do without a huge and increasing supply of metals. The Basic Goal of Extractive Metallurgy Understanding of some basic forces that shape this industry can be gained by consideration of the question: What determines the utility of metals to man? We think immediately of the inherent properties of metals - strength, ductility, electrical conductivity and so forth - but these tell only part of the story. Metal price and the available supply play equally

Jan 1, 1971

By A. W. H. Morris, E. A. Steigerwald

The jatzgue beizazriov oj Mietal matrix co))zpos~tes in tension -lensiom loading has been imestigated as a junction of Dolume fraclion veinfovcelnent using the model systems of a silver matrix reinforced with contlnuous or dzscontztinuous aligned tungsten jilamenls and continuous aligned steel filamenls. Appreciable impvocetnents in fatigue strength were obseved in all syslems inzvesLigated, the degree of sl renglhenng-increasing with increasing volume fraclion of reinforcement. The mode of fatigue failure was found to be a function of colutrre jp-actiotz and was also noted to be controlled by the relative fatigue and strength characlerislics of the matrix and reinforcemenl. THE advantages to be gained by suitably incorporating high-strength filaments or whiskers into metallic matrices are well-recognized.' To date emphasis has been placed on the experimental determination of tensile strengths and elastic moduli of metal matrix composites measured parallel to unidirectionally aligned filaments. Several attempts have been made to relate experimentally measured tensile properties to theoretical values calculated from the properties of the components on the basis of the relatively simple "rule of mixtures" analysis. However, relatively few data have been reported in the literature on the fatigue behavior and mechanism of fatigue failure of metal matrix composites. In a study of fatigue crack propagation in aluminum plus steel wires and aluminum plus tungsten wires, Forsyth et a1.2 found that the incorporation of small numbers of filaments suitably dispersed were capable of substantially reducing the rate of fatigue crack propagation. For this purpose, the strength of the filaments appeared to be more important than the aspect ratio and the authors reported that parallel filaments were not the most favorable orientation for increased strength. In a basic study of the fiber reinforcement of metals, Williams and 0'brien3 report preliminary results which indicate a considerable improvement in fatigue strength in reversed bending fatigue of a steel wire-reinforced aluminum alloy composite. In a study of the influence of interfacial bonding on fatigue behavior, Baker4 has also reported improved fatigue properties in stainless steel-reinforced aluminum composites. In contrast, Ham and place5 report that, although tensile properties are improved greatly by filament reinforcement, the reinforcement of copper with continuous, brittle tungsten wires up to 23 vol pct was comparatively ineffective against fatigue. The authors attribute the poor fatigue properties of the composite to fatigue hardening of the matrix at the tips of cracks which can build up stress concentrations sufficiently large to fracture proximate filaments. Baker and cratchley6 failed to find marked improvements in the reversed-bending fatigue properties of silica-reinforced aluminum. The study was complicated by the complex behavior in a composite during the compres-sive half-cycles imposed in this type of loading. This was manifested in the failure of the composites by de-lamination, a contributing factor being the presence of aluminum oxide at the matrix-filament interface. Prior to the general acceptance of filament-rein-

Jan 1, 1968

By James W. Halley

' FINE-GRAINED " steels have been standard products for many years. This paper describes an investigation of the effects of some of the more common grain-growth; inhibitors used to produce these steels. The properties, response to heat-treatment, and the deoxidation practice necessary to produce "fine-grained" steels have been the subjects of numerous papers. It has been shown that a substantial quantity of' aluminum is necessary to produce this type of steel, and it has been indicated that titanium and zirconium produce a similar result. For some time there was a lively argument between those who felt that aluminum refined the grain and those who felt that aluminum oxide was the effective agent. This argument subsided with an apparent victory for those promoting aluminum oxide. Most of the work on grain size has divided steels into two broad classifications based upon McQuaid and Ehn's original carburizing test at 1700°F. or some similar test at this temperature. If the steel coarsened at this temperature, it was coarse grained, while if it did not it was fine grained. Quantitative data concerning how much a certain amount of aluminum raised the coarsening temperature and affected the properties, all other factors being constant, are very meager. Similar information regarding titanium and zirconium is practically nonexistent. The published information on aluminum yields some quantitative information. Epstein, Nead and Washburn' gave the first quantitative information on the amount of aluminum necessary to prevent grain growth at 1700°F. They showed that the addition of a pound to a pound and a half of aluminum per ton (0.05 to 0.075 per cent) would assure steel that would not .coarsen during a McQuaid-Ehn test at 1700°F. Herty, McBride and Hough2 reported that a steel containing 0.020 per cent acid-soluble aluminum coarsened between 1742° and 1832°F., while steels containing 0.016 per cent and 0.017 per cent acid-soluble aluminum coarsened between 1652~ and 1742°F. compared with similar aluminum-free steels that started to coarsen at 1580°F. Herty3 also showed a marked improvement in low-temperature notched impact resistance with increasing acid-soluble aluminum up to 0.030 per cent. McQuaid4 compared the coarsening of steels containing 0.011 to 0.204 per cent total aluminum and found a maximum coarsening temperature at 0.098 per cent aluminum. He had no samples between 0.015 and 0.098 per cent aluminum. Houdrement5 found a marked decrease in coarsening temperature with aluminum contents above 0.50 per cent. Kinzel, Crafts and Egan6 found that aluminum and zirconium improved thy low-temperature impact resistance of a low-alloy steel, while titanium was detrimental. Sims7 shows that sulphur increases the coarsening temperature and that the maximum coarsening temperature is between 0.04and 0.06 Per cent added aluminum. The

Jan 1, 1946