Search Documents

By F. G. Smith

A FEW years ago, the writer encountered a, problem that, at first, seemed to be due to peculiar conditions affecting grain growth. Large cups made from heavy metal failed in the first drawing operation in the process of making seamless tubes. The metal, as cast, appeared to be sound and strong; it rolled successfully and withstood the first cupping operation, but on the first draw it failed, with a crystalline fracture. The failure appeared in the slightly worked part of the bottom of the cup, and microscopic examination revealed exceptionally large grains. Knowing the general conditions governing recrystallization of brass, which were later published by Matthewson and Phillips, an investigation was outlined with the idea of including various conditions under which new grains might form, and which would include the effect that a previous anneal might have upon the anneal following. These conditions were produced by annealing specimens of brass at five different temperatures, indenting them with a 10-inn. ball under four different pressures, and then reannealing at each of the five temperatures five specimens each of which had been annealed at one of the five temperatures.

Jan 8, 1919

By F. C. Foshag, P. E. Wingrove

The Kayford, Boone and Nicholas Division of Bethlehem Mines Corp. operates a modern coal preparation plant in Van, WV. Since start-up of the Van plant in 1976 until the summer of 1980, the refuse handling system proved to be a costly maintenance problem and a material handling bottleneck. During the 1980 two-week miners' vacation, the original system - which included two screw conveyors and a drag conveyor - was replaced by an installation using two Flexowall steep angle belt conveyors. This paper describes the technical and economic analysis that led to the new installation and reviews its first year operating performance.

Jan 1, 1983

Jan 1, 1959

By Kenneth Cotingham

Many factors joined in reducing drilling activity in Ohio in 1942. Conservation Order M-68 was important, but other things, such as operators and members of drilling crews joining the armed services and going into war plants, had an important part. The reduction in number of completions was considerable. In 1941, the total of wells drilled was 1561 but in 1942 the total was 1008. The total initial daily open flow discovered by the 701 gas wells drilled in 1941 was 492,000 M cu. ft., whereas the open flow of the 471 gas wells completed in 1942 was 314,488 M cu. ft. The total initial daily production of the 333 oil wells drilled in 1941 was 10,300 bbl., and in 1942 the 181 oil wells had a total daily initial of 7570 bbl. The average daily initial per gas well therefore was somewhat less in 1942 when compared with the preceding year, but the initial per ail well increased about 36 per cent over 1941. General Activity The total depth of the 652 oil and gas wells drilled in 1942 was 1,597,000 ft. The most active county was Perry, where 63 oil wells were drilled, most of them in Clayton township. In Morgan County. where 43 gas wells were drilled, the greatest activity was in York and Marion townships. Medina County was third in number of wells drilled, although of the total of 33 gas wells in the county, 26 were in the new Hinckley township pool. The total initial open flow of these 26 wells was 39,202 M CU. ft., and was considerably larger than from any other single area. Muskingum was an active county, particularly Washington and Wayne townships, in each of which seven gas wells were drilled, and Blue Rock and Harrison townships, in each of which five gas wells were drilled.

Jan 1, 1943

By Kenneth Cotingham

Many factors joined in reducing drilling activity in Ohio in 1942. Conservation Order M-68 was important, but other things, such as operators and members of drilling crews joining the armed services and going into war plants, had an important part. The reduction in number of completions was considerable. In 1941, the total of wells drilled was 1561 but in 1942 the total was 1008. The total initial daily open flow discovered by the 701 gas wells drilled in 1941 was 492,000 M cu. ft., whereas the open flow of the 471 gas wells completed in 1942 was 314,488 M cu. ft. The total initial daily production of the 333 oil wells drilled in 1941 was 10,300 bbl., and in 1942 the 181 oil wells had a total daily initial of 7570 bbl. The average daily initial per gas well therefore was somewhat less in 1942 when compared with the preceding year, but the initial per ail well increased about 36 per cent over 1941. General Activity The total depth of the 652 oil and gas wells drilled in 1942 was 1,597,000 ft. The most active county was Perry, where 63 oil wells were drilled, most of them in Clayton township. In Morgan County. where 43 gas wells were drilled, the greatest activity was in York and Marion townships. Medina County was third in number of wells drilled, although of the total of 33 gas wells in the county, 26 were in the new Hinckley township pool. The total initial open flow of these 26 wells was 39,202 M CU. ft., and was considerably larger than from any other single area. Muskingum was an active county, particularly Washington and Wayne townships, in each of which seven gas wells were drilled, and Blue Rock and Harrison townships, in each of which five gas wells were drilled.

Jan 1, 1943

By J. H. Mallery, J. H. Keeler

THE crystal structure of Zral, the compound richest in zirconium (91.03 pct Zr by weight) in the system Zr-Al, has been found to be ordered face-centered-cubic. This compound is of particular interest, since it is encountered as the precipitated phase in potentially useful zirconium-rich alloys. It forms peritectoidally from body-centered-cubic zirconium and Zr,Al at about 975°C. The Zr-A1 constitution diagram has been reported by McPherson and Hansen.' For the primary determination a 100 g ingot was prepared by arc-melting in a water-cooled copper crucible under purified argon. The raw materials were crystal-bar zirconium (a purity of better than 99.7 pct) and spectroscopically pure aluminum. The ingot was double melted, examined metallographi-cally, and found to be quite uniform as shown in Fig. 1. The hardness of the as-cast button was VHN 390 to 445. A 20 mil diam specimen was prepared from annealed (900°C) filings of Zr,Al. The specimen was mounted in a 5 cm radius powder camera and an 8 hr exposure was taken using copper radiation with a nickel filter. The structure of the compound Zral was found to be ordered face-centered-cubic of the Cuau type, with an a,, value of 4.37220.003A. Its calculated density is 5.976e0.013 g per cu cm. The relative intensities for the lines were calculated using the formula 1+cos2 20 I oc----------------- • p • /F7 sin2 0 cos 0 1 + COS' 20 where----------------is the Lorentz polarization fac- sin2 0 cos 0 tor, p is the multiplicity factor, and F is the structure factor. The X-ray data are given in Table I. The compound has exhibited plasticity when present as particles in a matrix of a zirconium. During hot working at about 900°C, the compound has been found to deform plastically to the extent that some of the particles exhibit a length-to-width ratio greater than 4:1 as shown in Fig. 2. In answer to the discussion of ref. 1, McPherson and Hansen pointed out that the compound may be cold rolled and reduced as much as 33 pct. Zr,Al has also been found2 under certain conditions to precipitate in lamellar form at grain boundaries of the a phase of hexagonal-close-packed zirconium. Acknowledgment This work was carried out under Contract W-31-109-Eng 52 for the United States Atomic Energy Commission.

Jan 1, 1956

CONTENTS [The Nature of Strain Markings in Alpha Brass (paper by J. E. BURKE and C. S. BARRETT, Met. Tech. Feb. 1948. TP 2327). ......................... 2 X Ray Studies of Twinning and Untwinning in Magnesium Alloys (paper by J. B. HESS and R. L. DIETRICH, Met. Tech. Feb. 1948. TP 2328) ................ 11 ]

Jan 1, 1948

By P. R. Sperry, P. A. Beck, J. Towers

Dahl and Pawlek1 found that electrolytic copper develops extremely coarse grains at 1000°C after about 90 pct reduction by rolling. This coarsening occurs only under conditions of penultimate grain size, deformation, and alloying which lead to the "cube" recrystallization texture.l,2,3,5 The peculiar angular shapes and straight grain boundaries of the coarse grains were noted by several investigator.1,4,5 On the other hand, coarsening in Fe-containing aluminum or in AI-Mn alloys8 does not depend on a "cube" (or any well developed) recrystallization texture. It is true that increasing deformation by rolling, and, therefore, an increasingly well developed re-crystallization texture, are associated with decreasing incubation periods of coarsening.6-7-8 Nevertheless, coarsening readily develops in aluminum even after only 30 pct reduction by rolling, where the recrystallization texture is very weak.6,8 Also, coarsening was observed by Jeffries9 many years ago in sintered thoriated tungsten, which presumably has no preferred orientation. In all these cases coarsening is associated with grain growth inhibition by a dispersed second phase.8,9 The annealing temperature has to be suficiently high to overcome the inhibition at a few locations. But if it is too high, growth starts at many points, and the resulting grain size becomes much smaller.9 Normally, the coarse grains are more or less equiaxed, and the boundaries have a typical ragged appearance.6.8 Cook and Macquarie4 demonstrated that, in addition to the texture-dependent coarsening previously found at 1000°C,l electrolytic tough pitch copper may also coarsen at 800°C after 50 pct reduction by cross rolling. The coarse grains formed under such conditions have rounded shapes and ragged boundaries, like those in aluminum. When the annealing temperature is higher, the tendency for their formation decreases. All these observations suggest that the coarsening at 800°C is associated with inhibition by a second phase. Actually, coarsening at 800°C after 50 pct reduction by cross rolling was observed only in tough pitch copper,4 which contains Cu2O particles. On the other hand, the texture-dependent 1000°C coarsening occurs in both tough pitch and oxygen-free copper;4 it does not appear to depend on the presence of a dispersed second phase. However, the interpretation of the 800°C coarsening in Cu after 50 pct rolling as an inhibition-dependent process, similar to the coarsening in A1-Mn alloys, is somewhat weakened by the fact that this coarsening was reported4 to occur only after cross rolling, and not after straight rolling. It was, therefore, decided to re-examine this question. A 1 in. diam electrolytic tough pitch copper rod, No. 2 hard drawn, was annealed for 20 min at 700°C, rolled to 0.5 in., annealed 10 min at 700°C, and straight rolled to 0.064 in. It was then given a penultimate anneal of 20 min at 500°C and it was cut into four sections, which were given final reductions by straight rolling as follows: A 30 pct reduction of area B 50 pct reduction of area C 70 pct reduction of area D 90 pct reduction of area Specimens cut from the four sections were finally annealed at 800°C in an oxidizing atmosphere. Strip A remained fine grained up to 10 hr, but the specimen annealed 12 hr consisted of only 2 large grains. Strip B had a few scattered large (1/2 to 3/4 mm) grains after 1 min, although the balance of the specimen consisted of fine grains of about 0.02 mm. After 5 min there were several 10 to 15 mm grains present, and after 1 hr strip B was completely coarsened. The coarse grains had the same characteristics (see Fig 1) as those obtained by Cook and Macquarie at 800°C after cross rolling. Strip C had several grains of 0.05 to 1 mm after 1 min, but it was still largely fine grained after 12 hr. After 48 hr it consisted entirely of grains of about 0.5 to 4 mm, with an extraordinarily large number of twin bands. Strip D remained com- pletely fine grained after 4 hr at 800°C. These results indicate that, in the deformation range of 30 to 70 pct reduction, the incubation period for coarsening as well as the rate of growth and the final size of the coarse grains decreases with increasing deformation. Similar

Jan 1, 1950

By T. A. Wright

THE CHAIRMAN.- With your permission, I shall read for F. W. Willard, who is ill, the keynote paper of a symposium that, I hope, will make us all aware of post-war problems as well as of the present-day problems in the more efficient use of secondary metals.

Jan 1, 1943

By Shiou-Chuan Sun

THE fact that coals of different ranks and even of the same rank differ greatly in their amenability to iroth flotation is well known. In recognition of the need for an explanation of this phenomenon, two hypotheses have been suggested. Wilkinsl reported that the floatability of coals increased with an increase of the carbon content or rank. This postulate is handicapped by the fact that bituminous coals that possess moderate carbon contents are actually more floatable than anthracite coals that have high carbon contents, as shown in columns 6 and 9 of Table I. Taggart and his associates' implied that the difference of floatability between bituminous and anthracite coal was caused by the variation of carbon-hydrogen ratio. This is not applicable to the relative floatability of other coals and carbons. For example, column 11 of Table I shows that the carbon-hydrogen ratios of low-floating lignitic coal and non-floating animal charcoal are not only smaller than the moderate-floating anthracite coal, but are also similar to the high-floating bituminous coal. Furthermore, according to this hypothesis, high temperature coke-A (464), Ceylon graphite (1238), and lamp-black (357), all possessing extremely high carbon-hydrogen ratios, should be less floatable than other substances having much lower carbon-hydrogen ratios such as high volatile-B bituminous coal (11.9 to 22), anthracite coal (35.7 to 60.5), lignitic coal (15.6 to 33.6), and charcoal (13 to 26.2). However the former group is actually more floatable than the latter group. In this paper, a surface components hypothesis is Proposed to explain the different floatabilities of coals, carbons, and hydrocarbon minerals. The validity of the hypothesis is experimentally supported by the actual floatability, natural floatability, wettability, and adsorbability for neutral oils of coals, carbons, and hydrocarbon minerals tested. The combustible recovery of the flotation results, as used in this paper. was calculated from Eq. 1: P (100-Ep) 100 RWCP Rc= [1] F (100-E,) C, where R, is the percent combustible recovery; F and P are, respectively, the weight of feed and the weight of concentrate or product; E, and Ep are, respectively, the total percent of ash plus moisture in feed and in concentrate; Ru. is the percent weight recovery: and C, and C, are, respectively, the percent of combustible in feed and in concentrate. Except for ash and moisture content, all chemical components of a coal are assumed combustible. The experimental work included studies on flotation, ultimate and proximate analyses, contact angle tests, extractions of bitumen-A with benzene, adsorptions for liquid hydrocarbons, and wetting tests. Most of the flotation experiments were performed in a laboratory Fagergren machine; others were tested in a small Denver machine. The solid feed for the former was 300 g and for the latter was 30 g. The solid materials used for flotation were crushed to —48 mesh. After the mineral pulp in the flotation cell was agitated for 6 min and the pH was adjusted to 7.5 & 0.2 with sodium hydroxide or hydrochloric acid, a petroleum light oil having a viscosity of 5.73 centipoises at 77 °F was added and conditioned for 2 min. Finally, pine oil was introduced and the froth was collected for exactly 3 min. The weight ratio of petroleum light oil to pine oil was kept constant at 1.5 to 1. Tap water was used for all flotation tests. Contact angles were measured with a captive bubble machine. For each coal sample, three specimens were mounted in transoptic mounts and polished with levigated alumina, first on a sheet glass, then on a cloth-covered metal polishing wheel. The polished specimen was first washed with distilled water and wiped thoroughly on a cleaned linen pad, then transferred into the pyrex cell of the captive bubble machine and conditioned for 6 min., and finally measured for contact angles at three or more points. Except where otherwise stated, the induction time for each measurement was 1 min. The contact angle representing each material was obtained by averaging the measurements of three specimens. The linen pad was first washed with warm distilled water, then boiled 30 min in a 2N sodium hydroxide solution, and finally washed with distilled water until no trace of sodium hydroxide could be detected in the decanted solution. The cleaned linen pad was stored under distilled water. Immediately before using, the pad was rewashed and transferred into a clean pyrex petri dish partly filled with distilled water. The glassware and rubber gloves used were cleaned by soaking in sulphuric acid-potassium dichromate cleaning solution, followed by rinsing with distilled water. The polished specimens were handled only by glass forceps. The ultimate and proximate analyses were made in accordance with the ASTM standard procedures for coal and coke. The extractable bitumen-A was determined by weighing 1 g of —100 mesh sample and placing it in a desiccated and weighed ASTM aluminum-extraction thimble. The thimble was placed in condenser hooks and inserted into an extraction flask containing 100 cu cm of benzene. The flask was heated and the benzene vapor was condensed by water coils. At the end of 24 hr of percolation, the thimble was removed, desiccated, and weighed. Loss in weight of sample was taken as bitumen-A and calculated to dry and ash-free basis.

Jan 1, 1955

By Fun-Den, Wang

An open pit rock structure usually contains geological planes of weakness. They are formed by joints, faults, bedding planes, fractures, and cleavages. Rock slope failures often occur in the form of sliding of rock blocks along a plane or several planes. Such a rock block has three- dimensional geometry, and consequently a vector method of analysis has been found useful in evaluating its stability. Rock blocks of a tetrahedral shape with one free surface have been analyzed by Londe. Rock blocks formed by sets of parallel joints have been analyzed by Wittke. The present chapter presents the analysis of rock blocks formed by planes of weakness of arbitrary orientation, and of three-dimensional geometry.

Jan 1, 1972

By J. C. Bradley

THE relation of annealing temperature to conductivity of copper wire has been determined.1 Conductivity hard was 98.26 per cent. After a 10-min. heating at 200° C. it was 98.69. By annealing 10 min. at 300° C. a large increase, to 100.93, occurred. Maximum conductivity, 101.15, was attained after a 500° C. anneal; thereafter it decreased to 100.53 after a 950° C. anneal. If copper is gassed the decrease is much more than this. MATERIAL AND METHOD The work was done on high grade electrolytic copper, 99.942 per cent. copper-plus silver, silver 0.0008 per cent. It was hot-rolled to 3 in., then cold drawn to 0.080 in. The wire was cut into 25 5-ft. lengths and numbered 1 to 25 as cut. Four samples were tested hard. The others were wound into 5-in. diameter coils. For the 100° C. heating a coil was put into water, the water brought to boiling, and the wire kept at this temperature for 10 min. For the higher temperatures the coils were placed in envelopes of sheet copper, a little water added, and the envelopes sealed by folding over the edges twice, and hammering them together. This kept the air out very well. The envelope and wire were brought to the desired temperature; this was maintained for 10 min., then the whole was water-quenched.

Jan 1, 1927

[Aamot, Olav Crone, (M'29) Chem. Engr., Elektrokemisk, Raadhusgt. 23, Oslo, Norway. Abadilla, Quirico A., (M'38) Min. Engr., Dir. Bureau of Mines, Manila, P. 1. Abbott, Agatin, (J'40) Asst. Geol., Trench Mine, Patagonia, Ariz. Abbott, Clarence E., (M'04) Civil Engr., V.P., Tennessee Coal Iron & R.R. Co., 1642 Brown Marx Bldg., Birmingham, Ala. Abel, Raymond L., (M'28) Prof., Chem. Engrg., Univ. of Pittsburgh, Pittsburgh, Pa. Abel. Walter D., (M'32) Min. Engr., Div. of Corporations, State of Calif., 403 California State Bldg., Los Angeles, Calif. Abele, Louis T., (M'31) 4800 Patterson Ave.. Richmond, Va. Abell, Leo M., (M'31) Research Met., Mount Morgan Ltd., Mount Morgan, Queens., Australia. Abenius, Hakan V., (M'37) c/o Falu Gruva, Falun, Sweden.]

Jan 1, 1940

By D. W. Fuerstenau

On page 1243, column 1, the first line of the author's reply should read "D. W. Fuerstenau (author's reply)---," rather than D. E., as printed. In the sentence immediately preceding the first equation (page 1243, column 2)' the word "none" was omitted. The sentence should read: "However, if enough ore is put into the mill [so] that none of the energy put into the mill is wasted on metal-to-metal impact, then the product should have size modulus determined by the relation: ..."

Jan 1, 1961

By Harry E. Krumlauf

The year 1957 was one of declining metal price and production. Many lead-zinc-copper mines were forced to close, and the remaining mines limited production to stay more in line with demand. High cost of labor, supplies, and equipment and high taxes aggravated the situation. Some operators postponed or abandoned expansion programs because of uncertain economic conditions. Output was curtailed by elimination of over- time employment and reduction of the working force. The number of employes laid off was small- reduction in the labor force was accomplished by not replacing those who left a company's employ.

Jan 2, 1958

By D. T. MacRoberts

A simple disturbance in a gas reservoir travels with a finite velocity which is nearly independent of the amplitude of the disturbance. As a result very complex transients may be set up which seriously affect observation at a well. The time of transient is much longer than commonly supposed. INTRODUCTION A change in pressure at a gas well is not propagated through the reservoir instantaneously but with a definite fin- ite velocity. Knowledge of the period ! of this transient is of value because: 1. Observations of pressure and flow-rate during the transient may affect interpretation of back-pressure tests. 2. Interference effects between wells may be used to determine continuity of formation. 3. Additional information concerning the physical characteris- tics may possibly be deduced from the behavior of a well during the transient. MATHEMATICAL DEVELOPMENT It will be assumed that the well is initially closed in and that the pressure is constant throlughout the reservoir. As the initial disturbance passes outward from the well it is further assumed that a logarithmic pressure distribution is established between the most distant point reached and the well, so that: <l> = ((/)r-<t>w) I ------------ + (/) . (1) Manuscript received at office of the Branch September 15. 1948. Paper presented at Branch Fall Meeting, Dallas. Texas. Oct. 4-6, 1948. r. = distance to any point between r and rw r = radius of drainge iw= radius of well (/) = potential (P for incompressible fluids, P2 for perfect gases) Up to the time the effect reaches the point r the production from the well will be: W= (Pr-P,,,) . (2) i b W = volume produced t = sand thickness F = fractional porosity Pr = reservoir pressure Pm = average pressure between r and rw Pb = atmospheric Pressure All pressures will subsequently be stated in atmospheres and the constant Pb will be omitted. This will be produced at a rate: dw t k (Pr³-PW2) do d 0 - . (3) log — Pw = pressure at the well k = permeability 0 = time = viscosity

Jan 1, 1949

By D. T. MacRoberts

A simple disturbance in a gas reservoir travels with a finite velocity which is nearly independent of the amplitude of the disturbance. As a result very complex transients may be set up which seriously affect observation at a well. The time of transient is much longer than commonly supposed. INTRODUCTION A change in pressure at a gas well is not propagated through the reservoir instantaneously but with a definite fin- ite velocity. Knowledge of the period ! of this transient is of value because: 1. Observations of pressure and flow-rate during the transient may affect interpretation of back-pressure tests. 2. Interference effects between wells may be used to determine continuity of formation. 3. Additional information concerning the physical characteris- tics may possibly be deduced from the behavior of a well during the transient. MATHEMATICAL DEVELOPMENT It will be assumed that the well is initially closed in and that the pressure is constant throlughout the reservoir. As the initial disturbance passes outward from the well it is further assumed that a logarithmic pressure distribution is established between the most distant point reached and the well, so that: <l> = ((/)r-<t>w) I ------------ + (/) . (1) Manuscript received at office of the Branch September 15. 1948. Paper presented at Branch Fall Meeting, Dallas. Texas. Oct. 4-6, 1948. r. = distance to any point between r and rw r = radius of drainge iw= radius of well (/) = potential (P for incompressible fluids, P2 for perfect gases) Up to the time the effect reaches the point r the production from the well will be: W= (Pr-P,,,) . (2) i b W = volume produced t = sand thickness F = fractional porosity Pr = reservoir pressure Pm = average pressure between r and rw Pb = atmospheric Pressure All pressures will subsequently be stated in atmospheres and the constant Pb will be omitted. This will be produced at a rate: dw t k (Pr³-PW2) do d 0 - . (3) log — Pw = pressure at the well k = permeability 0 = time = viscosity

Jan 1, 1949

By A. Hultgren, G. Phragmén

Page Outline of Progress of Knowledge and Theories about Gas Evolution in Steel Ingots. and Its Influence on Crystallization and Segregation................ 134 Object of Present Investigation........................................... 148 Theoretical Discussion of Process of Solidification........................... 149 Gas Given Off from Rimming Steel during Solidification................... 149 Equilibrium Diagram of the Iron-carbon-oxygen Alloys................... 151 Solidification of Pure Iron-carbon-oxygen Alloys.......................... 157 Solidification when Carbon Monoxide Is Given Off at Constant Pressure... 157 Solidification when Gas Evolution Is Suppressed....................... 158 Schematic Application on Solidification of Rimming-steel Ingots.......... 159 Influence of Manganese, Sulphur and Phosphorus......................... 160 Experimental work..................................................... 162 Liquid Steel and the Mold Gas......................................... 162 Ingots Investigated and Methods Used.................................. 165 Ingot structure....................................................... 174 Structure of Rim Zone.............................................. 174 Structure of Core................................................... 181 Structures Obtained under Special Conditions of Freezing................ 182 Distribution of Metalloids............................................. 187 Other Observations Made............................................. 192 General Discussion of Solidification Process................................. 195 Condition of Liquid Steel before Casting................................. 195 Rimming Period...................................................... 202 Composition of Rim Zone............................................. 225 Freezing after Top Is Closed........................................... 228 Slag Inclusions and Ingot Scum........................................ 234 Reaction between Gas in Blowholes and Surrounding Solid Steel during Cooling 235 Summary.............................................................. 237 Appendix—Preparation and Etching of Ingot Sections....................... 238 References............................................................. 239 In 1934, Jernkontoret (The Swedish Ironmasters&apos; Association) appointed a committee for the study of the structure of rimming-steel ingots and the various phenomena associated with their solidification. The members of the committee, including those who have joined it later, have been: I. Bohm, B. D. Enlund, B. Kalling, M. Tigerschiöld, S. Wohlfahrt and the authors. The present paper‡ is a somewhat

Jan 1, 1939

By G. Phragmén, A. Hultgren

Page Outline of Progress of Knowledge and Theories about Gas Evolution in Steel Ingots. and Its Influence on Crystallization and Segregation................ 134 Object of Present Investigation........................................... 148 Theoretical Discussion of Process of Solidification........................... 149 Gas Given Off from Rimming Steel during Solidification................... 149 Equilibrium Diagram of the Iron-carbon-oxygen Alloys................... 151 Solidification of Pure Iron-carbon-oxygen Alloys.......................... 157 Solidification when Carbon Monoxide Is Given Off at Constant Pressure... 157 Solidification when Gas Evolution Is Suppressed....................... 158 Schematic Application on Solidification of Rimming-steel Ingots.......... 159 Influence of Manganese, Sulphur and Phosphorus......................... 160 Experimental work..................................................... 162 Liquid Steel and the Mold Gas......................................... 162 Ingots Investigated and Methods Used.................................. 165 Ingot structure....................................................... 174 Structure of Rim Zone.............................................. 174 Structure of Core................................................... 181 Structures Obtained under Special Conditions of Freezing................ 182 Distribution of Metalloids............................................. 187 Other Observations Made............................................. 192 General Discussion of Solidification Process................................. 195 Condition of Liquid Steel before Casting................................. 195 Rimming Period...................................................... 202 Composition of Rim Zone............................................. 225 Freezing after Top Is Closed........................................... 228 Slag Inclusions and Ingot Scum........................................ 234 Reaction between Gas in Blowholes and Surrounding Solid Steel during Cooling 235 Summary.............................................................. 237 Appendix—Preparation and Etching of Ingot Sections....................... 238 References............................................................. 239 In 1934, Jernkontoret (The Swedish Ironmasters&apos; Association) appointed a committee for the study of the structure of rimming-steel ingots and the various phenomena associated with their solidification. The members of the committee, including those who have joined it later, have been: I. Bohm, B. D. Enlund, B. Kalling, M. Tigerschiöld, S. Wohlfahrt and the authors. The present paper‡ is a somewhat

Jan 1, 1939

By Robert H. Richards

(Read at the Amenia Meeting, October, 1877.) DURING the winter of 1868-9, I was called upon by Professor F. H. Storer, to put up the Bunsen filter pump in the chemical laboratory of the Masschusetts Institute of Technology. As the laboratory is on the lower floor, it was found necessary to use a great deal of cumbrous pipe and apparatus to get the necessary column. It was then suggested that if an instrument could be devised which would make use of the hydrant pressure in the service-pipe, it would do away with the objectionable features of the Bunsen pump. After using the Bunsen pump for some years, the jet pump to be described in this paper was devised, and it has since been adopted by Prof. Wing in the quantitative laboratory of the school. I am much indebted to Prof. Wing for his aid in starting the manufacture in brass of these jet pumps, which are now to be had in Boston. The jet pump much resembles the Giffard injector in form. It differs from it in the fact that water is the impelling fluid, and air the impelled, while with the injector steam is used to impel water. The principle of condensation of steam, which is Water availed of in the injector, is entirely wanting in the jet pump. The jet pump consists in a water jet, w, (see figure), a constriction or waist, a, and a waste tube, o. The success of the jet pump depends on the following conditions 1. The relation between the sizes of sectional area of a and w. 2. The proximity of a and w. 3. The form and angle of the two hollow cones whose vertices make the constriction a. 4. The relative size of sectional area of w and o. 5. The zigzags, or an equivalent means of making foam. In the following discussion, let a, w, and o represent the diameters of these parts of the jet pump. A number of experiments were tried to ascertain

Jan 1, 1878