Search Documents

By R. E. Miner, J. K. Jackson, T. L. Wilson

THE nature of the decomposition reactions producing hardening in aluminum-rich A1-Ag alloys is now fairly well understood. The silver is not uniformly dispersed even at temperatures above the solvus line: rather, it is clustered into zones and associated with dislocations.' During quenching, nearly all of the silver segregates into zones' and some is attracted to dislocations, producing stacking faults. Growth of these faults produces the semicoherent y precipitate.1 During aging, the larger zones and the y precipitates grow at the expense of the smaller zones. The large zones persist up to about 350°C; where they redissolve in favor of the y' and y precipitates.' The equilibrium hcp y precipitate occurs both by a cellular reaction at the grain boundaries1 and by growth of the Y' plates to a critical size where incoherency results. Damask and Nowick 4 observed an internal friction peak in an A1-6 at. pct Ag alloy at about 140°C (0.25 cps). The peak was found to exhibit a systematic instability. After aging at successively higher temperatures between 155' and 23Z°C, the peak first migrated to higher temperatures while increasing in height, then returned to lower temperatures and decreased in height. After aging at temperatures above about 200°C, the peak position remained constant while the height decreased very slowly. In quenched specimens, elastic after-effect measurements inhcated a rapid initial transient in peak position from low temperatures up to 155°C. The authors concluded that a stress induced growth and resolution of the clusters and the 7' was the most reasonable mechanism to account for the behavior. It would seem, however, very unlikely that both the clusters and the y' precipitate would provide damping contributions whose relaxation time and activation energies were identical, which is required for them to produce the same internal friction peak. The present investigation was motivated by this apparent anomaly and the development of a very low thermal inertia torsion pendulum5 capable of monitoring transient behavior. Low frequency internal friction measurements were made on four binary A1-Ag alloys nominally containing 5, 10: 15, and 20 at. pct Ag. The results of measurements made on a 10 at. pct Ag alloy in the quenched condition are shown in Fig. 1. There are two peaks apparent in the spectrum, one centered at about 160°C, the second at about 210°C. The two peak spectrum was observed in each alloy, but it was best resolved in the 10 pct Ag specimens. Because of the instability in the internal friction, 4 it seemed possible that the second peak was not a peak at all, but simply a manifestation of a single, sharply transient, peak. This effect has been observed in Au-Ni alloys.6 The existence of the higher tempera-

Jan 1, 1970

By Francis O. Blackwell

There are few industries in which power is more important to successful operation than mining, and none in which it is so difficult to ohtain power cheaply. Fuel is usually expeusive in mining districts, ana the ma chinery may be widely scattered and located in places difficult of access. The work is often so intermittent and variable as to prevent the economical use of steam. Mining operations are likely to exhibit accumulations of comparatively small and inefficient engines, numerous boilers and long lines of wasteful steam-pipes. Conlpressed air, as a means of transmitting power, is so handicapped by losses in the compressors and piping that it is limited to short distances and to the operation of apparatus requiring power, without regard to cost. To-day, electricity is rapidly replacing other methods of power-distribution, primarily because it is practically independent of distance. By selecting a potential proportional to the length of transmission, the cost of electric conductors and the e5ciency are the same for all distances within reasonable limits. For instance, a given amount of power can be delivered either 528 ft. away at 100 volts, or 50 miles at 50,000 volts, with the same total of copper per H.P. and with exactly the same loss of power in the transmissioo-circuk. This independence of distance permits the selection of the place most advantageous for power-development as a site for an electric power-plant, and the co~~centration there of the generation of all the power required within a radius of many miles. The powel.-site may be at a fall of water, if one is available, or a steam-plant can be built where fuel and supplies are cheapest, or where suflicient water is available for boiler-feed and condensing purposes.

Jan 1, 1904

By Christopher H. Bierbaum

The first significant fact observed in the study of bearing metals is that not a single pure homogeneous metal has given satisfactory service; all bearing metals are alloys made up of two or more phases; that is, they consist of hard and of relatively soft microscopic particles intimately mixed. The function of the hard particles, or bearing crystals, is to support the load and resist the wear when actual metallic contact exists between the bearing surfaces. The functions of the softer particles are to allow the harder particles to adjust themselves to the surface requireinents of the journal and to wear down slightly below the surface of the harder, forming slight depressions on the apparently smooth wearing surface of the bearing, in which some of the lubricant is held when the bearing surfaces are brought into contact with each other. It is this characteristic of certain alloys to form these slight depressions, and thus provide the means for retaining a lubricant, that characterizes them as true bearing metals; in fact, a bearing metal has been defined as "an alloy that is capable of retaining a lubricant upon a bearing surface."' The extent to which the lubricant can be so held determines the most valuable characteristic of an alloy as a bearing metal. An alloy which, perhaps, most characteristically represents a bearing metal is the composition of copper and tin that contains sufficient tin to produce the tin-copper eutectoid, or delta crystal. The depressions worn upon the surfaces of the softer crystals of the teeth of a motor-truck worm wheel, made of an ll-per cent. tin bronze, in many cases were from 5 to 6 microns in depth; all other conditions remaining constant, this depth of wear increases with an increase of working pressure. This copper-tin bronze contains intercrystalline shrinkage cavities, which also

Jan 1, 1923

By Christopher H. Bierbaum

The first significant fact observed in the study of bearing metals is that not a single pure homogeneous metal has given satisfactory service; all bearing metals are alloys made up of two or more phases; that is, they consist of hard and of relatively soft microscopic particles intimately mixed. The function of the hard particles, or bearing crystals, is to support the load and resist the wear when actual metallic contact exists between the bearing surfaces. The functions of the softer particles are to allow the harder particles to adjust themselves to the surface requireinents of the journal and to wear down slightly below the surface of the harder, forming slight depressions on the apparently smooth wearing surface of the bearing, in which some of the lubricant is held when the bearing surfaces are brought into contact with each other. It is this characteristic of certain alloys to form these slight depressions, and thus provide the means for retaining a lubricant, that characterizes them as true bearing metals; in fact, a bearing metal has been defined as "an alloy that is capable of retaining a lubricant upon a bearing surface."' The extent to which the lubricant can be so held determines the most valuable characteristic of an alloy as a bearing metal. An alloy which, perhaps, most characteristically represents a bearing metal is the composition of copper and tin that contains sufficient tin to produce the tin-copper eutectoid, or delta crystal. The depressions worn upon the surfaces of the softer crystals of the teeth of a motor-truck worm wheel, made of an ll-per cent. tin bronze, in many cases were from 5 to 6 microns in depth; all other conditions remaining constant, this depth of wear increases with an increase of working pressure. This copper-tin bronze contains intercrystalline shrinkage cavities, which also

Jan 1, 1923

By Oliver C. Ralston, Foster Fraas

VIRTUALLY all commercial use of electrostatic separation has employed separators depending on differences of conductance of the broken, solid mixtures treated by them. The two main types of conductance separators have been: (1) Those in which the separating field is as near a static field between two charged electrodes as it is possible to maintain in the face of the usual leakage that takes place between electrodes with some 5 to 50 kv tension between them and spacing of l/z to 3 in.; (2) those in which a convective discharge of corona or spray type, but not a spark discharge, takes place between the carrier electrode and a charged electrode facing it, which is of very restricted area, such as a row of needle points or a small diameter wire parallel to the face of the carrier electrode. The present paper deals with this latter type. The principle is usable in separators where the carrier electrode, usually grounded, has the shape of a roller, a conveyor belt, a vibrating table, a sloping chute, or a nearly vertical plate. The innovation studied by us has been the use of the convective field for charging material on the carrier electrode and succeeded by a field between the carrier electrode and an electrode made of a true dielectric which cannot take on a charge by conduction but is charged by being in the radius of the corona discharge. The acquired charge is of the same sign as that of the corona but is not dischargable by contact with a good conductor. However, high-tension charge tends to leak off because of the ionization of the ambient air. The field between this electrode and the carrier electrode is as near static as it is possible to obtain. There are some differences in behavior of this electrode and that of the gas tube electrode used by Sutton, as will be discussed below. Both electrodes cause increased adhesion of nonconductive particles to the carrier roll. The particles are pinned there because they are convectively charged on their outer surfaces facing the corona electrode. The electrodes also cause increased rate of release of conductive particles tending to be pinned by corona charging but conveying the charge to the grounded carrier roll almost as rapidly as it is received by the particles.

Jan 10, 1950

By C. Y. Ang, C. Wert

Quench aging of supersaturated solid solutions of nitrogen in columbium takes place in reasonable times in the temperature range 300&apos; to 500°C. Changes in internal friction, hardness, and electrical resistivity are found to accompany this change. THERE is practically no detailed information in the literature concerning interstitial solid solutions in either columbium or tantalum. The fact that both of these metals are used extensively commercially in both pure and alloyed states makes studies of their properties of value. While the plan is to study both these metals and their alloys extensively, so far only a small number of measurements have been made. This paper presents data obtained in the initial investigations of columbium. The principal interstitial impurities of columbium are likely to be hydrogen, carbon, oxygen, and nitrogen. The first of these, hydrogen, is outside the scope of internal friction measurements at present and nothing quantitative is known about the initial hydrogen content of the specimens. However, it is believed that it is completely absent after the preliminary heat treatments are carried out. The carbon content of the original samples is low and can be reduced still further during sample preparation. Oxygen is normally present to some extent in columbium and can also be added or removed easily. Nitrogen is also normally present in small amounts and can also be controlled within limits. Since it is not possible yet to remove all the nitrogen from columbium and since it is possible to remove essentially all the oxygen and carbon, initial measurements were made on the alloy system nitrogen in columbium. In this sense then, the alloys are true binary alloys. Little is known about the effects of nitrogen on the physical and metallurgical properties of columbium, so it was necessary to perform some rather elementary measurements on the specimens. These measurements are described briefly in the next section and are discussed in detail in later sections. Scope of the Work That internal friction is associated with diffusion of nitrogen in columbium has been known for some time. It is similar in nature to that for carbon and nitrogen in a-iron. In these latter cases, the information obtained from internal friction has been useful metallurgically.&apos; and it is not too much to expect useful information from similar studies on columbium containing nitrogen. The technique of internal friction measurements is adequately described by Ke2 At a frequency of 1 cps the internal friction peak for nitrogen in columbium occurs at 300°C and that for oxygen at 160°C." So that all the measurements will be meaningful metallurgically, the internal friction has been calibrated by making a measurement of the damping at the two peaks and a measurement of oxygen and nitrogen content by chemical analysis. A comparison of the two gives the following calibration factor: To go from damping capacity expressed in terms of 1/Q to weight percent of oxygen and nitrogen in solid solution in columbium, multiply the peak values of internal friction by about 4 and 3 respectively." Data from which these factors were calculated are presented in Table I. The increase of electrical resistance of columbium caused by the addition of oxygen and nitrogen as interstitial impurities has been quantitatively determined. At room temperature the percentage increase is small for small additions of impurities (<0.1 wt pct); as the temperature is lowered it becomes an increasingly larger factor of the total resistance. An empirical relation has been established to express the resistivity at — 195°C in terms of weight percent of oxygen and nitrogen in solid solution. It is easy to make supersaturated solid solutions of nitrogen in columbium and to observe aging phenomena. The optimum aging temperature, as in the case for carbon and nitrogen in a-iron, occurs at the temperature for which the time necessary for a single place-change in diffusion is about 1 to 10 millisec. This means for nitrogen in columbium that significant property changes should take place for this alloy at about 400" to 500°C in reasonable time intervals. Results of such aging experiments are

Jan 1, 1954

By J. B. Seabrook

The accompanying Fig 1 is a graphical scheme of intermediate accuracy for expediting interconversions of mol, weight, and volume percents. This chart consists of a family of curves of mol or atomic or volume percent plotted against weight percent, each curve in the family providing for a certain ratio of molecular or atomic weights or densities. Thus, the whole range of variations is presented in a very familiar format, and the conversion is effected simply by choosing the proper curve and reading off the required values. An entire series of conversions for a given binary system can be found by following the appropriate curve. It is interesting to examine the analytical geometry of the plots. The curves, which must fit into a square and all join at the 0 and 100 pet points, may be shown to be hyperbolas with their centers on the extension of the diagonal of the square which they intersect. Multiplying out the expression x A atomic fraction of A = y = ------ where x is the weight fraction of A, and A and B are atomic weights, we get xy+A/By- A/Bxy=x Upon rotating and translating axes and avoiding imaginaries, it is found that the angle of rotation is —45°, the origin moves upv2/2 units andv2/2(A/B+1/A/B-1) units to the right, and the standard form is Thus the curves are equilateral hyperbolas, their centers are units away from their intersection with

Jan 1, 1950

By Arno C. Fieldner

METALLURGICAL coke and the by-products of the carbonization of coal continue in strong demand. Nearly 500 new by-product ovens were constructed in 1943. Output of by-product coke in the first ten months of the year was about 2 1/2 percent higher than in the corresponding period of 1942, but beehive production remained on approximately the same level as last year and constituted about 11 per cent of the total coke output.

Jan 1, 1944

By Damon H. McFadden

5.1-1. Geographic and Geologic Factors. Surface mines are located where the coal seam can be economically uncovered and where the product can be utilized competitively with other fuels. The planning and designing of a pit may follow various procedures. The sequence for consideration of the influential factors as considered here may not be complete for every pit, nor will it be necessary to be completely used in each design. It is suggested as a check and outline for the engineering approach. Controlling conditions for the layout should be listed and considered with the facilities and equipment for the exploitation. After these items, as listed below, have been discussed and the feasibility agreed upon, then the actual planning and design of the pit can be done. GEOGRAPHIC FEATURES. The location of the coal area sets the climatic stage. The rainfall, the temperature extremes, and the general weather conditions all affect the design of the pit. Overburden soil when wet may not be stackable and may be impossible to move by standard procedures. The coal seam itself may be so soft that it must not be traveled on when wet, as the losses may be the difference between a profitable venture and an unsuccessful one. Some equipment will work well on dry soil only, just as a dredge works only in the wet. The conditions must be checked and analyzed. Some equipment cannot handle frozen soil (wheel excavators), so temperature extremes must be noted. The extreme weather conditions may also govern the expected working days and therefore the ultimate production. The altitude (atmospheric pressure) may affect the equipment, and this should be checked. All of these conditions should be noted on the preliminary map of the area. GEOLOGIC FACTORS. The geologic and surface conditions of the coal field dictate the type of pit generally feasible. Rough terrain, rolling terrain,

Jan 1, 1968

By V. Lepetic, C. C. Harris

A systematic program of investigations covering all aspects of cell hydrodynamics,1-3 flotation kinetics,4,5 surface chemistry and their interactions has as a major objective the elucidation of the flotation micromechanism and the principles of cell design and scale-up.6 Purely from the scale-up point of view, a family of reactors should enable different throughputs of the same material to be similarly treated or, at least, to be treated in a manner which differs beween reactors in a predictable way. Thus, for the same material and residence time, the recovery and grade from differently sized cells of the same family should, ideally, be similar or, at least, be related to each other in a known way. It is well known, however, that different-sized cells do not always achieve similar results, and it is necessary to enquire into the reasons for these differences. For example, it may be that the relative dimensions of different-sized cells result in hydrodynamic conditions which preclude similarity; if so, different scaling may improve the situation. The major question concerns identifying the dynamic conditions and their associated geometric requirements which govern the flotation process, and the criteria which are necessary for their fulfillment. It is to answer such questions that the program referred to earlier was instituted. In connection with this program and in order to examine data concerning the physical features and operating conditions of existing flotation cells, the following survey was carried out. This work represents an approach which is complementary to experimental investigations, for it recognizes that the design of existing cells may embody several of the principles being sought. If data for enough cells, especially families of cells, are examined, some broad requirements common to all cells may emerge.

Jan 9, 1966

By E. K. Landis

IK connection with the interesting paper of Mr. Glenn on "Sampling Ores Without Use of Machinery " (page 156 of the present volume), I venture to offer the results of ten years&apos; experience in the sampling of iron-ore by a method adopted when I first became

Jan 1, 1892

By J. O. Nomland

Bahrein &apos;Island.—In 1936 the Bahrein Petroleum Co. continued drilling additional wells to further increase production. In all, 39 flowing wells have now been finished and five others are drilling. A second well has been deepened for prospecting the deeper horizons but has not been successfully completed as a commercial producer. In addition, a well has recently been drilled near the eastern limit of the producing area for edge-water observation. The present system places wells 3000 ft. apart in a rhombic grid, or about one well to 179 acres. The total production for the year was 4,644,635 barrels. It is expected that refinery capacity of 20,000 bbl. per day will have been completed by July, 1937. A new permanent and enlarged camp with office buildings is being built. A new hospital has been constructed and two additional medical men have been added to the staff. Saudi Arabia.—In eastern Saudi Arabia, the California Arabian Standard Oil Co. has continued with the program of prospect drilling started in 1935. After the gas encountered in Dammam well No. 1 had been successfully shut off, it was completed as a small flowing well of 51" gravity oil. Dammam No. 2, which had been started in 1935, tested 3840 bbl. of approximately 50" gravity oil from a depth of 2175 ft. Dammam No. 5, before being deepened for prospecting lower productive horizons, encountered a gas zone producing 30 million feet. Five other wells on the Dammam dome are in various stages of drilling or completion. Most of these have been located principally to outline the productive area and the various producing horizons of the structure. An extensive program of geological work is being continued. In June, 1936, a well was started on the El &apos;Alat structure about 25 miles northwest of the Dammam development. Although various tar showings have been reported, the well has not yet, at 2518 ft., reached the depth at which it has been thought that productive horizons might be encountered. A prospect well is being drilled by the Kuwait Oil Co. (jointly owned by Gulf and Anglo-Iranian Oil Companies) in the Sheikdom of Kuwait. The well is near Bahra, a few miles north of Kuwait Bay and about 240 miles northwest of El &apos;Alat. To date no favorable results at depth of about 6000 ft. have been reported.

Jan 1, 1937

By J. H. Berryman

THE use of oxygen as a bath reagent in hearth furnaces during the refining period is a familiar story. Investigations and tests in which oxygen was substituted for iron ore to reduce carbon date back 25 years and include the work of Bigge,1 Browne,2 and Chelius.3 During this past year the majority of the experimental work in the use of oxygen was carried on mainly in open-hearth shops, since it was felt that the greater field for application lay in this type of furnace. Much constructive work was done in evaluating the carbon-oxygen relationships, as reported by Slottman and Lounsberry4 and by Hughes.5 Steelmakers using the electric furnace have been actively engaged meanwhile in an experimental program of their own, with such success that the oxygen injection pipe has become a tool in the day to day production of low-carbon and stainless steels.

Jan 1, 1947

By Albert E. Reed

The development of the modern highspeed vibrating screen, together with the increasing availability of long-lasting stainless-steel screen cloth for relatively fine-mesh separations, means that more screen circuits will be used in the future. It seems pertinent therefore to examine a few characteristics of screen-circuit products, and especially the points of difference as compared with products of classifier circuits. The most noticeable change that takes place when substituting screening for classification in a grinding circuit is a substantial drop in the circulating load, owing to the greater ease with which the "fines" leave the circuit. Where circulating loads of 500 to 600 per cent are considered fairly normal in classifier grinding circuits, the grinding circuit equipped with screens for equivalent work will have a circulating load of only 20 to 75 per cent. As a result, the products of screen circuits will show a minimum of overgrinding or sliming as compared with a classifier circuit. The desirability of this characteristic will naturally vary according to the metallurgical requirement in each case. Because screen separations make a sharper division according to particle size, the products of screen circuits can be expected to show greater crowding of particles near the point of separation. These changes in product characteristics are so important that other factors, both in the grinding and concentration processes must be adjusted if the operator is to take full advantage of the increased tonnages and higher efficiencies available to him through the use of the screen circuit. One factor that too often is overlooked when changing to screen circuits is the importance of adjusting the ball-mill or rod-mill charge, to compensate for: (I) increased tonnage of new feed, (2) decreased circulating load, or (3) more granular character of feed. These same factors should also be taken into consideration for their effect on the various types of concentration or flotation equipment that may follow the screen circuit. Over a period of years, this equipment has generally been designed and adjusted to the product of the classifier, therefore it seems obvious that some research on the adjustment and adaptation of concentrating and flotation equipment to screen-circuit products will be most profitable to the operators. To illustrate the points mentioned above, the results from three recent installations follow, with data on the comparative characteristics of screen and classifier circuits. A range of separation from 10 to 48 mesh has been chosen, using two general types of screening equipment and two types of classifiers. The first of the installations of which the results are to be examined is that of an iron-ore installation where eastern magnetite was being concentrated prior to sintering. Fig. I shows the original grinding circuit, using classification, while Fig. 2 shows the same circuit equipped with a

Jan 1, 1947

By Albert E. Reed

The development of the modern highspeed vibrating screen, together with the increasing availability of long-lasting stainless-steel screen cloth for relatively fine-mesh separations, means that more screen circuits will be used in the future. It seems pertinent therefore to examine a few characteristics of screen-circuit products, and especially the points of difference as compared with products of classifier circuits. The most noticeable change that takes place when substituting screening for classification in a grinding circuit is a substantial drop in the circulating load, owing to the greater ease with which the "fines" leave the circuit. Where circulating loads of 500 to 600 per cent are considered fairly normal in classifier grinding circuits, the grinding circuit equipped with screens for equivalent work will have a circulating load of only 20 to 75 per cent. As a result, the products of screen circuits will show a minimum of overgrinding or sliming as compared with a classifier circuit. The desirability of this characteristic will naturally vary according to the metallurgical requirement in each case. Because screen separations make a sharper division according to particle size, the products of screen circuits can be expected to show greater crowding of particles near the point of separation. These changes in product characteristics are so important that other factors, both in the grinding and concentration processes must be adjusted if the operator is to take full advantage of the increased tonnages and higher efficiencies available to him through the use of the screen circuit. One factor that too often is overlooked when changing to screen circuits is the importance of adjusting the ball-mill or rod-mill charge, to compensate for: (I) increased tonnage of new feed, (2) decreased circulating load, or (3) more granular character of feed. These same factors should also be taken into consideration for their effect on the various types of concentration or flotation equipment that may follow the screen circuit. Over a period of years, this equipment has generally been designed and adjusted to the product of the classifier, therefore it seems obvious that some research on the adjustment and adaptation of concentrating and flotation equipment to screen-circuit products will be most profitable to the operators. To illustrate the points mentioned above, the results from three recent installations follow, with data on the comparative characteristics of screen and classifier circuits. A range of separation from 10 to 48 mesh has been chosen, using two general types of screening equipment and two types of classifiers. The first of the installations of which the results are to be examined is that of an iron-ore installation where eastern magnetite was being concentrated prior to sintering. Fig. I shows the original grinding circuit, using classification, while Fig. 2 shows the same circuit equipped with a

Jan 1, 1947

By R. Casting, J. Philibert, and C. Crussard

APPARATUS described in this paper uses the properties of X-radiation, emitted by substances under electron bombardment, as a means of rapid chemical point analysis. The method is based upon the principles of emission X-ray spectrography pioneered by Moseley in 1913. A very finely focused beam of electrons—the electron probe—is projected on the surface of a sample, which has a very large area compared with the beam diameter, at the point where it is desired to know the chemical composition. The minute volume of the sample which is thus irradiated emits a complex X-ray spectrum consisting principally of the characteristic radiations of the elements present in the volume. Measurement of the wavelength and intensity of each component of this spectrum thus affords a simple method of determining the chemical identity and concentration of these elements. The volume of sample which is analyzed at each position of the beam is limited by the diffusion of electrons in the sample. For an accelerating potential of the electron beam of about 30 kv, which is a convenient value for producing the characteristic radiation, this diffusion extends over a diameter of about 1 µ normal to the beam, and about 2 µ in the direction of the beam. Thus a beam of 1 µ in diameter leads to a volume of about 2 µ in diameter being irradiated. The limits of the analyzed region are thus considerably smaller than those obtained by using spark or arc emission spectrometry, which must extend to about 50 µ at right angles to the beam, and those obtained in X-ray fluorescence analysis, where the penetration of the specimen is considerably greater. The apparatus itself consists of three main parts: an electron optical system. an X-ray spectrograph and an optical microscope. The electron opticai system consists of a tungsten cathode emitting the electrow and a pair of magnetic lenses which focus the electron beam on the specimen to be analyzed. The specimen is prepared in the usual way, as in optical micrography. The X-radiation, emitted at the focal spot where the electrons strike the sample, is analyzed with a curved crystal, Geiger-Müller counter, vacuum spectrograph. The light microscope, designed to observe the surface of the sample in the region to be analyzed, is provided with a reflecting objective placed on the axis of the second magnetic lens. Its magnification is X450. The quantitative determination of an element A in the analyzed region is made by measuring the intensity I, of a strong characteristic line of the element, as emitted from the sample, and then the intensity I (A) of this same line as emitted from a

Jan 1, 1958

By R. D. Lee

A simplification of the method of Hurst and McCarty for conducting potentiometric model studies by the single probe method is presented along with experimentally determined invasion patterns for certain idealized flow problems. The analytical solution for one class of these problems is given. Finally, a general description is given of a newly developed instrument which permits direct mapping of flow lines and determination of transit times in potentiometric-model studies. Introduction The object of this paper is to present: I. A simplification of the method of Hurst and McCarty for conducting poten-tiometric-model studies of oil and gas reservoirs by the single probe method. 2. Results of a series of studies of certain idealized flow problems and the general conclusions to be drawn therefrom. 3. A description of a new instrument, the Chronocartograph, which greatly reduces the labor and time required for conducting potentiometric-model studies. Certain general conclusions may be drawn as results of the investigation of the idealized flow problems. They are: I. Injection and extraction areas should be separated by as great a distance as conditions permit since, in general, the recovery prior to first breakthrough tends to vary as the square of this distance. 2. Little advantage is to be gained by use of more than eight injection wells or groups of injection wells for the case of circular productive limits. 3. Elongated shapes of productive limits are best exploited by injection on the extended major axis only, with a line of extraction wells lying on the major axis. 4. The use of peripheral injection wells for elongated shapes is permissible, if necessary, but requires extension of the line of extraction wells. The exploitation of an oil or gas field is effected either by the expansion of the gas and oil, or by their displacement by another fluid. Both methods may be used simultaneously. When the displacement of the oil or gas is the controlling factor there arises the problem of mapping the progress of the boundary between the fluid in place and the displacing fluid. This problem is of particular interest in the operation of a cycling project in a gas-condensate field, where the wet gas is produced from one or more wells, commonly called "extraction wells.&apos;&apos; This wet gas is taken into a processing plant where the condensate is removed. The remaining "dry" gas is injected back into the field through one or more wells, called "injection wells," both to conserve the gas for future use and also to maintain the pressure in the field. In an operation of this type it is essential to anticipate the manner in which the dry gas will spread through the field, because the ultimate recovery of the wet gas depends

Jan 1, 1948

By R. D. Lee

A simplification of the method of Hurst and McCarty for conducting potentiometric model studies by the single probe method is presented along with experimentally determined invasion patterns for certain idealized flow problems. The analytical solution for one class of these problems is given. Finally, a general description is given of a newly developed instrument which permits direct mapping of flow lines and determination of transit times in potentiometric-model studies. Introduction The object of this paper is to present: I. A simplification of the method of Hurst and McCarty for conducting poten-tiometric-model studies of oil and gas reservoirs by the single probe method. 2. Results of a series of studies of certain idealized flow problems and the general conclusions to be drawn therefrom. 3. A description of a new instrument, the Chronocartograph, which greatly reduces the labor and time required for conducting potentiometric-model studies. Certain general conclusions may be drawn as results of the investigation of the idealized flow problems. They are: I. Injection and extraction areas should be separated by as great a distance as conditions permit since, in general, the recovery prior to first breakthrough tends to vary as the square of this distance. 2. Little advantage is to be gained by use of more than eight injection wells or groups of injection wells for the case of circular productive limits. 3. Elongated shapes of productive limits are best exploited by injection on the extended major axis only, with a line of extraction wells lying on the major axis. 4. The use of peripheral injection wells for elongated shapes is permissible, if necessary, but requires extension of the line of extraction wells. The exploitation of an oil or gas field is effected either by the expansion of the gas and oil, or by their displacement by another fluid. Both methods may be used simultaneously. When the displacement of the oil or gas is the controlling factor there arises the problem of mapping the progress of the boundary between the fluid in place and the displacing fluid. This problem is of particular interest in the operation of a cycling project in a gas-condensate field, where the wet gas is produced from one or more wells, commonly called "extraction wells.&apos;&apos; This wet gas is taken into a processing plant where the condensate is removed. The remaining "dry" gas is injected back into the field through one or more wells, called "injection wells," both to conserve the gas for future use and also to maintain the pressure in the field. In an operation of this type it is essential to anticipate the manner in which the dry gas will spread through the field, because the ultimate recovery of the wet gas depends

Jan 1, 1948

By D. R. Conlon, E. R. Brownscombe

Errors in measurement of reservoir pressure include: (I) gauge errors, and (a) interpretation errors. Gauge errors may be reduced by: (a) reading charts with a comparator microscope, (b) use of hard metal stylus points to give clear lines, (6) insuring temperature equilibrium, and (d) making multiple tests. Check calibrations are equally as important as check well tests. A statistical analysis of such check runs shows quantitatively the advantages of a standardized "zero pressure line&apos;&apos; and of the use of field calibrations made at bottom-hole temperature on the same chart run in the well. Interpretation errors include: (a) fluid heads, which should be corrected to the top of the perforations on the basis of well-fluid gravity and from the top of the perforation to the datum level on the basis of reservoir-fluid gravity, and (b) gradients around the well. Conventional shut-in periods may be entirely inadequate to overcome these, necessitating a reservoir study based on build-up curve data, reservoir history, core analysis and any other available information. Interest in engineering studies of the pressure changes in oil and gas reservoirs is increasing. This type of work yields important information and doubtless will be greatly extended in the future. One of the factors limiting the work, however, is the accuracy with which the reservoir pressures can be determined; for if the inaccuracies in the pressure measurements represent an appreciable percentage of the pressure changes, the engineer is seriously handicapped, and must delay the reservoir study until the reservoir pressure has changed a relatively large amount. This delay can greatly reduce the benefits of such studies, at least from the point of view of aiding the leasing, drilling and completion programs. Thus, from the point of view of reservoir analysis, it is frequently important to obtain the most accurate pressure data possible early in the history of any field—particularly for the gas-distillate fields now being developed. This paper deals with improvements in the measurement of bottom-hole pressures that permit pressures even as high as 4000 or 5000 lb. per sq. in. to be determined with gauge errors of only+ ±I to 2 lb. per sq. in. Since pressures out in the reservoir rather than in the bottom of the hole concern the reservoir analyst, differences between bottom-hole pressures and actual reservoir pressures are also considered. In general, errors in pressure measurement may be divided into: 1. Gauge errors: a. Errors due to inaccuracies in reading the pressure charts. b. Errors due to irreproducibility of the pressure element and recording system. c. Errors caused by failure to allow the gauge to reach temperature equilibrium. 2. Internretation errors: a. Errors caused by a fluid head between the gauge position in tubing and the pressure at the datum level in the reservoir. b. Pressure gradients in the reservoir.

Jan 1, 1946

By D. R. Conlon, E. R. Brownscombe

Errors in measurement of reservoir pressure include: (I) gauge errors, and (a) interpretation errors. Gauge errors may be reduced by: (a) reading charts with a comparator microscope, (b) use of hard metal stylus points to give clear lines, (6) insuring temperature equilibrium, and (d) making multiple tests. Check calibrations are equally as important as check well tests. A statistical analysis of such check runs shows quantitatively the advantages of a standardized "zero pressure line&apos;&apos; and of the use of field calibrations made at bottom-hole temperature on the same chart run in the well. Interpretation errors include: (a) fluid heads, which should be corrected to the top of the perforations on the basis of well-fluid gravity and from the top of the perforation to the datum level on the basis of reservoir-fluid gravity, and (b) gradients around the well. Conventional shut-in periods may be entirely inadequate to overcome these, necessitating a reservoir study based on build-up curve data, reservoir history, core analysis and any other available information. Interest in engineering studies of the pressure changes in oil and gas reservoirs is increasing. This type of work yields important information and doubtless will be greatly extended in the future. One of the factors limiting the work, however, is the accuracy with which the reservoir pressures can be determined; for if the inaccuracies in the pressure measurements represent an appreciable percentage of the pressure changes, the engineer is seriously handicapped, and must delay the reservoir study until the reservoir pressure has changed a relatively large amount. This delay can greatly reduce the benefits of such studies, at least from the point of view of aiding the leasing, drilling and completion programs. Thus, from the point of view of reservoir analysis, it is frequently important to obtain the most accurate pressure data possible early in the history of any field—particularly for the gas-distillate fields now being developed. This paper deals with improvements in the measurement of bottom-hole pressures that permit pressures even as high as 4000 or 5000 lb. per sq. in. to be determined with gauge errors of only+ ±I to 2 lb. per sq. in. Since pressures out in the reservoir rather than in the bottom of the hole concern the reservoir analyst, differences between bottom-hole pressures and actual reservoir pressures are also considered. In general, errors in pressure measurement may be divided into: 1. Gauge errors: a. Errors due to inaccuracies in reading the pressure charts. b. Errors due to irreproducibility of the pressure element and recording system. c. Errors caused by failure to allow the gauge to reach temperature equilibrium. 2. Internretation errors: a. Errors caused by a fluid head between the gauge position in tubing and the pressure at the datum level in the reservoir. b. Pressure gradients in the reservoir.

Jan 1, 1946