Search Documents

By understanding the ore breakage characteristics and utilising comminution circuit modelling, the benefits of SAG mill feed size manipulation can be readily assessed. This paper looks at the benefits and problems of total secondary crushing of mill feed and advocates partial secondary crushing as a means of improving grinding efficiency for certain hard ores. Case studies are reviewed for new and existing SAG mill circuits.

Jan 1, 2007

By Juan Carlos Salas

In this paper, a collaborative R&D model which has been successfully applied by a global mining companies association is presented and analysed both from the conceptual and practical point of view and an example of these collaborative initiatives, the Copper Technology Roadmap recently generated by a group of the most relevant copper mining companies, is presented, including an analysis of strategic opportunities and challenges in the Latin American region.

Sep 9, 2007

By Pertti Paavola, Hikki Rasanen

This paper describes a very exacting tunneling project. Planning and technical realization of this service and transportation tunnel was especially difficult as a matter of vibration control, because the tunnel is situated only a few meters under Maria Hospital, which is one of the most busiest hospitals in Helsinki. In this hospital there are many departments for bedpatients, research and treatment with high-tech equipment, operational surgery and a big laboratory. Besides access tunnels are situated near several apartment buildings. The functionality of the tunnel required the placement of the access tunnels to be straight towards these apartment buildings for which special care for blast induced air pressure had to be taken.

Jan 1, 1997

Jan 1, 1968

By I. J. Barker

Keywords: Submerged-arc furnace, plasma furnace, d.c. furnace, scale up, Søderberg electrodes, smart grid, demand side management, load shedding This paper argues that the scale up of furnaces and the supply of electricity are going to be two major issues that will affect the ferro-alloy industry in the near future, and that economic factors will drive this development. The most common type of furnace for producing ferro-alloys at present is the submerged-arc furnace with three electrodes, fed from a three-phase a.c. electrical supply. The scale up of this technology has now reached a fundamental constraint, which is caused by the electrical reactance of the secondary circuit. If the economy of any further scale up is to be achieved in the future then a different technology will have to be used. The supply of electrical power in future is likely to become a more complex issue than it is at present. Existing submerged-arc furnaces tend to run at fairly steady loads, but the ability to swing the load under demand-side management may offer advantages, and may allow a furnace to get cheaper power from the organisations that supply this power. This will have to be counterbalanced against the nuisance factors incurred by having a varying load in the operation of the furnace. Various options are therefore discussed in this paper. The possibility of scale up of Søderberg electrodes is discussed, as well as the use of d.c. power and multiple electrodes. Some of the issues with load swinging are also examined. A particular scenario is also briefly presented to show that considerable further scale up of ferro-alloy furnaces is still possible.

Jan 1, 2011

By I. R. Firth, D. L. Taylor

The ability to accurately model the movement of grade boundaries during a typical bench blast would be of significant benefit to mine operators. The movement of grade boundaries during the blasting process may have significant impact on grade recovery if not accounted for. The paper describes the preliminary stages of a research project which combines numerical blast models and conventional mine planning software to allow practical use of the results of a numerical blast simulation. A two dimensional bench blast is simulated using the Universal Distinct Element Code (UDEC). The results of the simulation are used to provide input to the Surpac mine planning package which can be used to generate grade control plans.

Jan 1, 2001

By K. Rainer Massarsch

The effects of soil displacement caused by pile driving on adjacent piles and structures are discussed. A method is proposed to estimate the point of force equilibrium which makes it possible to calculate up-lift forces and pile head movements. For the case of pre-coring a method is proposed to estimate the stability of the bore hole, based on cavity expansion theory. Model tests were performed to establish the displacement pattern of the soil during the driving of a pile group. It can be concluded that at the ground surface, already installed piles have little influence on the lateral displacements, but reduce significantly the soil heave. During the driving of a pile group, the soil is displaced according to a complicated pattern, which is strongly influenced by the order in which the piles are driven. In clay the displaced soil volume corresponds to the total volume of driven piles.

Jan 1, 1989

By Syd S. Peng, C. Y. Chen

Introduction The Surface Mining Control and Reclamation Act was passed in 1977 to put an end to the uneven environmental standards and enforcement established by various coal mining states in the US. One year after passage, the Secretary of Interior was directed to promulgate permanent program regulations implementing Title V provisions of the Act. These regulations were to form the basis for state regulatory programs under the Act and to allow states to assume primary regulatory responsibility. To implement the underground mining provision of the Act, the Secretary is directed in section 516(a) of the Act to promulgate rules. But they must take into consideration the differences between surface and underground coal mining. The regulations developed by the Secretary in 1979, with respect to subsidence control, included: • a subsidence control plan as part of the permitting process; • substantive provisions establishing performance standards for subsidence control; and • provisions providing for the prohibition of mining under perennial streams, impoundments larger than 24.6 dam3 (20 acre ft), and certain public facilities and urban areas. Industry challenged the Secretary's regulations implementing the subsidence control provisions. The litigation was consolidated with all other challenges to the permanent program regulations. (Permanent Surface Mining Regulation Litigation, Civil Action No. 79-1144; D. D.C., May 16, 1980.) In two opinions dealing with the multitude of issues raised by both industry and environmental groups, the US District Court of the District of Columbia ruled against industry. It upheld the promulgated subsidence control provisions. The US Court of Appeals stayed the appeals pending the agency's review and revision of its regulations. The regulatory reform was conducted in accordance with the order from the Secretary of Interior and the President in 1981. As a result, the subsidence control regulation was revised, reproposed, and finalized in June 1983 (Federal Register). This regulation, along with others, was again challenged by environmental groups and industry. On Oct. 1, 1984, the court, after finding the Secretary's reading of the Act reasonable, upheld the 1983 subsidence regulation except for one section. On Feb. 21, 1985, in accordance with the court's ruling, the Office of Surface Mining (OSM) suspended a portion of 30 CFR 817.121 (c)(2) concerning the damage correction requirement for structures or facilities and reproposed it on July 8, 1985 (Federal Register). In conjunction with a request for public comments, OSM now also seeks comments on the omission from the 1983 rule of the requirement in the 1979 rule regarding a presubsidence survey and monitoring of damage to structures. Technical issues related to subsidence regulations The subsidence regulations of June 1, 1983, consist mainly of two parts: a subsidence control plan as part of the permitting process; and substantive provisions establishing performance standards. The latter also includes provisions for prohibiting mining under certain areas. Under subsidence control plan section 784.20, minimum require-

Jan 2, 1986

The HB 2500 hydraulic breaker attachment from Atlas Copco Construction Tools features Krupp percussion technology and a service weight of 2,500 kg (5,512 lbs). This makes it ideal for demolition, tunneling, trenching, foundation work, rock mining and secondary breaking. Suitable for carriers in the 29-to 43-t (32-to 47-st) weight class, the HB 2500 accepts maximum hydraulic flow of 219 L/min (58 gpm) at 18 MPa (2,610 psi) of pressure, and delivers an impact rate of up to 550 blows per minute. The HB 2500 features PowerAdapt, a new system that automatically shuts down the breaker in the event that it receives excessive oil pressure from the carrier.

Jan 1, 2006

By Larry A. Haas

The U.S. Bureau of Mines is investigating ways of enhancing the high-temperature softening-melting (HTSM) properties of domestic taconite pellets. These properties, which are important for determining the performance of pellets in blast furnaces, include pellet bed contraction, pressure drop, S-value (area under the pressure-temperature curve), and softening and metal-slag drainout temperatures. Experiments showed that HTSM properties were related to the physiochemical properties (fired strengths and reducibilities) of pellets containing different levels of limestone and dolomite flux. Flux additions resulted in slightly lower green and fired pellet strengths, but improved metallurgical properties, such as reducibility. The influence of reduction conditions on HTSM properties was evaluated by varying the pellet metallization starting temperature and the carbon monoxide content of the CO-N2 gas mixture. HTSM property change was more sensitive to flux addition levels when metallization was initiated at 1,100° C with 20 pct CO in the gas stream. The S-value and the metal-slag drainout temperature were found to be the best criteria for characterizing HTSM properties. The optimum flux addition level was about 8 pct (4 pct dolomite, 4 pct limestone) or a basicity of about 1. At higher flux levels, a higher metal-slag drainout temperature was obtained.

Jan 1, 2010

By Anil Bhandari

Using subsurface data collected at each drilled shaft location is an ideal approach for conducting drilled shaft design. However, conducting subsurface tests at each drilled shaft location and subsequently performing the drilled shaft design can be a daunting task for a noise barrier wall that is divided into six (6) sections and stretches for approximately four (4) miles. In addition, having individual drilled shaft designs complicates the construction process. Grouping the subsurface conditions into broad categories and performing the design for each of those categories is an attractive alternative to the design per boring approach. Currently there are no existing guidelines to aid a designer on grouping the subsurface conditions for the drilled shaft design for the noise barrier walls. Therefore, a method was developed based on the Standard Penetration Test (SPT) N values of the near surface soils to categorize the soil profiles into distinct categories. Since the soil engineering properties of the near surface soils are known to be critical for drilled shaft lateral capacity, these soils were emphasized in the methodology. This method was successfully implemented for the design of drilled shafts supporting the noise barrier walls along the I-20 in Columbia, SC. For this project, two distinct soil profiles, labeled as ?strong? and ?weak?, were used. An overview of the soil profile grouping methodology is presented as well as the vertical and lateral drilled shaft capacity analyses for this project for the two general soil profiles. The analyses indicated that the axial capacity governed the design in the ?weak? soil profile and the lateral capacity controlled the design in the ?strong? soil profile. However, this is not a generalization and whether the axial or the lateral capacity governs the design of drilled shaft depends on the soil profile and design loads. Nonetheless, our findings emphasize that both lateral and axial capacity should be checked for drilled shaft design even when the vertical load are minor.

Jan 1, 2011

By James A. Madonna

Several universities and colleges in Australia, Canada and the United States, recognized the need to establish or reorganize geoscience programs at the vocational and two-year technical levels. To accomplish this, a cooperative study with industry in one state or province from each country was initiated. These include Tasmania in Australia, British Columbia in Canada and Alaska in the United States. The objective of this work was to develop a diversified geoscience educational model at the two-year technical, vocational and continuing education level that provides the source from which any nation can draw the proper educational tools to create a new geoscience program, modernize an existing program or strengthen a weak program. More than 100 mineral industry organizations provided information regarding their specific training needs for support personnel. The data gathered have been used to identify training areas for semi-skilled, skilled and technical personnel in geochemical mineral exploration. These included geological, geochemical, environmental and computer skills. With the areas of major educational need defined for geochemical exploration, an educational field skills model was developed for the three levels of training. The international need for a study of this type was recognized as early as 1980, following numerous contacts from domestic and foreign geoscience educators regarding the structure and success of training within the University of Alaska Fairbanks Mining Extension program, located in Fairbanks. Contacts, correspondence and visits included educators from Australia, Brazil, Canada, Mozambique and the conterminous United States. The need was magnified between 1985 and 1989 at the University of Alaska Fairbanks, when an attempt failed at initiating and developing a two-year geoscience vocational-technology program leading to an Associate of Science degree.

Jan 1, 1994

Jan 1, 1944

Jan 1, 1944

By A B. Christie, F P. Bierlein

Lode gold deposits of the Western and Eastern provinces, South Island, New Zealand , formed as a part of the Cordilleran-style tectonism during Tasman/Tahua and Rangitata orogenesis along the Paleozoic-middle Mesozoic southern Gondwanan margin. These deposits, hosted by lower grade greenschist facies sedimentary rock sequences of the Buller, Takaka, Torlesse, and Caples terranes, universally show geological features that are consistent with the orogenic gold deposit model, and genetic features are generally suggestive of a metamorphic origin, with the possible exception of a magmatic fluid source for the mineralisation at Sams Creek. However, ore fluid chemistry in Mesozoic deposits of the Eastern province, particularly the low concentration of non-aqueous volatiles and the very dilute nature of the fluids, is uncharacteristic of most orogenic gold deposits; this must be explained by either a unique fluid source or fluid type, which we believe unlikely, or an unrecognised significance of relatively rare gas-rich fluid inclusions in the deposits. Absolute age data for gold deposits in both provinces remain equivocal, thus hindering definition of the exact temporal relationship between ore formation and terrane accretion, regional metamorphism, and magmatic arc emplacement. Mercury and antimony occurrences in subgreenschist grade parts of the Haast Schist may target the upper levels of unrecognised orogenic gold deposits. If low-grade, high-tonnage intrusion-related gold systems occur on the South Island, then they are most likely to be discovered in association with the small molybdenite-, scheelite-, or cassiterite-bearing quartz stockworks spatially related to the Karamea and Median batholiths.

Jan 1, 2005

The ERMS Process was developed during four years of testwork by Austpac Gold NL to overcome the severe metallurgical problems of the ilmenite atWestport, in the South Island. These deposits have been known for about one hundred years. They were originally mined for gold, and only later attracted attention as a possible source of titanium minerals.   The resource is of world scale and may exceed 20 million tonnes of contained ilmenite. Similar deposits occur at Barrytown further south and together these areas would constitute an important opportunity for export-oriented mineral development, if a viable beneficiation technology were available. Further processing is essential, as the composition of the ilmenite is well below market specifications.

Jan 1, 1993

By A. R. Miller, M. C. Bétournay, D. L. Barnes

"A number of successful proof-of-concept projects have been carried out to replace conventional power application, such as diesel and rechargeable batteries, in underground mine vehicles. This has led to the development and testing of the world’s first fuel cell production vehicle, a mine locomotive. A fuel cell loader is being built and tested.This paper provides an insight into other projects that are being carried out. Some are related to further underground applications, and some to further research, such as refueling options, power plant durability, and vehicle automation.Also outlined is an evaluation of the overall mining applications and advantages this technology can bring to underground mining, including the facilitation of automation and tele-remote operation."

Jan 1, 2003

By D R. Swinbourne, T Lehner

Study of the distribution of minor elements between copper matte andfayalite slag is important in determining appropriate methods tomaximise the recovery of valuable metals and the rejection of harmfulelements. Boliden Mineral AB operate a large copper smelter in northern Sweden, where they had noted that the loss of silver to the slag in the settling furnace appeared to be a direct function of the tin content of the slag. This work was aimed at determining whether or not this was a cause-and-effect relationship. Copper matte containing approximately 50 wt per cent copper and small amounts of silver and tin was equilibrated with silica-saturated fayalite slag at 1250¦C, then quenched. The matte and slag were then analysed for their silver and tin contents. It was found that there was no relationship between the silver distribution and the tin distribution. The silver matte/slag distribution ratio had a value of 120 ¦ 40 while that for tin was 2.8 ¦ 0.3. It is suggested that the most likely cause of the relationship observed at the Boliden smelter was matte entrainment in the slag.

Jan 1, 1999

By Michael Karmis

The International Conference on Sustainable Development Indicators in the Mineral Industries(SDIMI 2003) was held May 21-23, 2003 on the island of Milos, Greece. The objective of this international conference was to assist the mining and minerals industries in their global transition to sustainable development. The main theme of the conference was the development, monitoring and assessment of sustainable development criteria for mineral operations. Emerging technologies were also presented that can assist in the development of criteria and performance indicators.

Jan 1, 2003

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1980 was $328.6 million, a decrease of $7.8 million from 1979. Cement, crushed stone, lime, clays, and sand and gravel continued as the major commodities produced. Alabama led the Nation in the production of crushed marble; was second in bauxite; third in native asphalt, ferroalloys, kaolin, and oyster shell; fourth in dimension marble, masonry cement, and bentonite; and fifth in fire clay and lime. Alabama ranked in the top 20 States in total value of non-metallic minerals produced. Adverse economic conditions in the construction and metals industries impacted on the minerals industry in Alabama. Mineral producers supplying raw or finished materials to these industries experienced periodic reductions in sales during the year. Unit price increases did not keep up with inflation.

Jan 1, 1982