Search Documents

By David K. Denton

Results of the mineral resource study of the Upper Priest Lake RARE II study area indicate a low potential for the discovery and economic recovery of silver and lead in the Prichard Formation near contacts with the Kaniksu Batholith in the vicinity of the Mountain Chief Mine (fig. 1). Silver and lead minerals locally occur disseminated and in irregular quartz fissure-fillings in the Prichard Formation. Between 18^6 and 1967, 105 lode raining claims were located in the study area. The area was designated for "further planning" in the Final Environmental statement but was later changed to "nonwilderness" by President Carter after work was scheduled for the area.

Jan 1, 1981

By C. Gherghel

The planning and operation of ventilation network systems for uranium mines require special considerations since ventilation is the primary technique of controlling ambient concentrations of radon progeny. The major environmental challenge facing the ventilation engineer is the requirement to dilute radon progeny to below the Working Level Month per year of worker exposure required by law. The application of large airflow volumes and the utilization of low residence times constitute some of the factors considered by the design engineer. Good mine planning and sequencing are also critical for protecting the health of miners. The mine ventilation must have such characteristics as flexibility, high air distribution efficiency, rapid air transit times, zero recirculation and no short-circuiting. A well established maintenance program for all ventilation appliances must be in place to guarantee control of the distribution system. Real-time monitoring systems permit assurance the adequate quality of air is delivered to working places. A case study for an operating mine is used to demonstrate how the ventilation system is successfully managed and operated using the above concepts.

Jan 1, 2009

By Robert Pack

INTRODUCTION SOONER or later in the development of any natural resource it becomes highly desirable to know the quantity of this resource in the country as a whole, as well as of the part that is being developed, for the general course and. conduct of the development work must be governed to some extent by the total supply available. An accurate estimate of the quantity of any natural resource is difficult to make; yet if one is diligent enough one can obtain a pretty accurate idea of the quantity of marketable timber, the acreage of tillable land, or the horsepower that may be developed from the streams, for these are things that may be measured. But any attempt to estimate the quantity of some mineral in the ground appears to enter the realm of imagination and it seems that the estimate can be nothing more than a blind guess. It may appear to be especially futile to attempt to determine the quantity of oil and gas that is available in the ground, for these minerals are so vagrant that even if the quantity now available should be known quite exactly, the quantity that will eventually be obtained may be much less, for certain losses in the extraction of both oil and gas are unavoidable, and just what these losses will be cannot be predicted. Though necessarily inaccurate, estimates of such mineral reserves are, however, of distinct value, for they summarize the existing knowledge of the deposits of the mineral and thus enable those who are interested in some industry that depends in one way or another on this mineral to formulate a rational commercial policy. Some time ago, when the price of gasoline suddenly rose in a rather spectacular manner, the writer was one of the U. S. Geological Survey geologists called upon to help to estimate the quantity of oil that could be obtained in the United States, for the fear had become widespread that perhaps the rate of increase in the price of gasoline was a measure of the rate of depletion of the supply of petroleum. It thus became his

Jan 8, 1917

A study was undertaken to investigate the relationship between the quantity and value of economic demonstrated resources discovered for 12 mineral commodities over a ten year period and the expenditure required to yield such mineable resources. The results showed that for every dollar spent on exploration, there is an apparent in-ground average value of around $54 dollars contained in the economic resources found. While this appears to be a satisfactory return, it should be remembered that more than 99.9% of exploration programs are judged to be failures because a viable ore body or mineral deposit was not proved up. What is behind this seeming paradox?   The fundamental truth behind mineral exploration is the fact that the more you explore, the more you find, and that one success will often lead to further discoveries. It appears that one rich and viable deposit creates such surplus that its inherent high value ('the pot of gold') makes up for all the failures. In short, mineral exploration is a high risk business with uncertain returns. However, with skill, enthusiasm, experience and venture capital, it can yield larger than normal returns for the brave and the fortunate.   Analysis of exploration expenditure and economic resources discovered for the period 1987 to 1996 revealed that the apparent in-ground value of economic ore discovered per dollar of exploration expenditure varied from a high of $429 for iron ore and $261 for bauxite to a low of $22 for gold and for lead, and $5 per dollar of diamond exploration expenditure. Preliminary conclusions drawn on the reasons for the variations observed include the inherent ease or difficulty of discovery for different mineral commodities which may in some cases, relate to the natural prospectivity of Australia as a whole. Layered deposits like iron ore and bauxite appear to yield higher in-ground value returns on the exploration dollar. To some explorationists, this may be considered as seemingly obvious, but it may have more to do with very large-exploration tenement grants pursued by various Australian State Governments in the early 1950s and 1960s than the apparent ease of delineating a stratabound deposit.   Despite the apparent relatively low in-ground value produced by the gold exploration dollar of $22, the 5660 tonnes of gold discovered in this ten year period was worth $9.1 billion and representing over a quarter of the new mineral wealth created in the ten years to 1996. This contribution, along with that from the other minerals discovered over the period, led to a significant boost to Australia's export income and standard of living.   It is concluded that, given the nexus between the amount of mineral exploration expenditure and the quantity of new resources likely to be discovered, this knowledge may help policy makers seek to influence the rate of resource discovery in countries like Australia for the benefit of the nation.

Jan 1, 2004

By Nikhil Dhawan

Electronic waste (e-waste) is a collective name given to discarded electronic devices such as Television, Cellular Phones and Personal Computers. Among the heterogeneous metals present in the e-waste are the base metals: copper, aluminium, nickel, tin, zinc, iron and precious metals: gold, silver, palladium, platinum apart from several hazardous and halogens metals. Hence there is a need to recover these metals from electronic scrap by recycling and then re-use, which can meet large amount of metals demand. Hydrometallurgical processing was employed for the recovery of metals from television printed circuit board (TV PCB). Different lixiviants such as hydrochloric acid, Sulphuric acid, and nitric acid were used to understand the dissolution behavior of copper, iron and lead present in the TV PCB. Effect of increasing concentration of nitric acid was also studied. Selective recovery of tin over 95% in the form of tin oxide was precipitated. The precipitated tin oxide was identified by X-ray diffraction technique. Tin oxide of purity more than 99.9% was obtained.

Jan 1, 2009

By S. H. Ash, E. M. Brooks

"Many of the hoisting slopes at the mines in the State of Washington are driven on extra steep dips. To facilitate hoisting they are driven wide enough to provide two tracks. The cars are handled by high-speed, first-motion electric hoists and the trips run in balance.The State mining laws a provide that special man-cars be provided on slopes of 20° or more and that no one be allowed to ride while any loaded car is being hoisted in any slope in a mine. Obviously, in addition to the fact that it is more or less hazardous to ride while an empty trip is being hoisted, considerable hoisting time is lost during the day if some one has to ride the trips in the slope.Owing to the locations of pumps and various types of equipment, more or less travel is required up and down the slope. Not only to provide a proper safety factor but also to comply with the law, some other means of transportation in an¬other passageway is desirable. This is sometimes recognized in large mines by pro viding separate hoisting shafts, or slopes, and necessary equipment, which are use for transporting men and material. The handling of material in itself would justify the system in most large mines.The following description of an automatic electric man-hoist was prepared from data furnished through the courtesy of Mr. Thomas Murphy, superintendent of the Northwestern Improvement Company's mines in the Roslyn-Cle Elum coal field.The special features of this hoist are that no hoistman is required and its operation is always under the control of the person or persons riding the trip.The hoist was installed at mine No. 5, Roslyn, Washington, to provide a means of entering and leaving the mine on idle days or at night when no hoistman was on duty and to make it unnecessary to use the main hoist for a man trip during working hours. It has been in operation for about two years and has given very satisfactory service.The hoist, with all accessories, is housed in a concrete building 200 feet back from and in direct line with one of the main airways. One car with a capacity of six men operates over a distance of 1,200 feet on a 38° pitch.The wiring details of the electric circuits which control the operation of the hoist are shown in Figure 1-a.The hoist is driven through a worm gear by a 500-volt shunt-wound direct-current motor at a car speed of 120 feet per' minute. A gravity friction brake with magnetic release is mounted on the- motor shaft and is wired in multiple with the motor field coils. The hoist drum is also equipped with emergency friction brakes, which operate by gravity and are released, in case of overspeed, by the governor geared direct to the drum shaft. When these brakes set the control circuit is opened at contact 2E-2C and the motor stops.If the descending car meets some obstruction and is stopped, the hoist continues to run and unwind the rope. To guard against this occurrence, a weighted sheave wheel rides the rope 4 feet from the drum, and if the rope becomes slack the rider drops downward and opens the contact 2C-2E which stops the hoist.Limit switches, S1 and S2, are located on the hoist indicator, which is connected to the drum shaft through sprockets and chain. The pointer P indicates the position of the hoist at all times."

Jul 1, 1930

Underground mine planning is characterised by a series of designs, starting with prefeasibility and culminating in operational. Information on the mineralisation and geotechnical conditions is available in increasing levels of detail, as development occurs. In the recently completed AMIRA Planning and Rapid Integrated Mine Optimisation (PRIMO) project, a methodology for producing good strategic and then tactical designs using new optimisation tools, was developed. At the strategic level, fundamental decisions must be made such as those relating to cut-off grade, bench heights, mining methods, access and haulage systems, properties of the mill, etc. The inputs are the block and financial models, geotechnical data, infrastructure and production costs, etc. Stope definition for strategic designs includes bench RLs (relative levels), orebody envelopes, and design and placement of amalgamated or simplified stopes. If multiple mining methods are under consideration, then stopes need to be associated with these. Access design must take into account decisions such as declines versus shafts, a template for level layouts and the topology of the access network. Some of the geotechnical and physical constraints are relaxed for strategic design stages. Strategic scheduling is high level, from a month to a year at a time. In the PRIMO project, software tools have been developed enabling the mine planner to rapidly produce a large number of such strategic designs. After the designs have been evaluated, the highest value designs are chosen and a small number of these can then be further refined at a tactical level. For these designs, the first step is determination of all stopes meeting physical and geotechnical requirements and constraints, allowing for complex stope shapes. Next, detailed layout of the mine access network is obtained, satisfying all operational and geotechnical constraints. Finally, more detailed scheduling is performed, over shorter time periods. The Melbourne University group has focused on optimal access design. In particular, the access network is optimised for minimum cost, taking into account the cost of haulage and development over the lifetime of the mine. Costs vary over the different parts of the network depending on the quantity of haulage and so a weighted network optimisation problem has to be solved. We have developed two software tools for this task, decline optimisation tool (DOT) and planar underground network optimiser (PUNO). DOT produces an optimal network of declines and crosscuts connecting access points on the levels to a portal or break-out point from existing infrastructure. PUNO designs the level layout, including footwall and hanging wall drives, development drives and connections to vent raises. A survey will be given of the capabilities of DOT and PUNO when used on some recent case studies. Our current goals include incorporating some aspects of ventilation design and modelling the development costs when additional ground support is required. This is an abstract only. A full paper was not prepared for this abstract.

Dec 6, 2010

By S. K. Gilman, V. E. Hugo

A common problem encountered in the mineral sands industry is that the mineralogical measurements used in defining the resource are not readily converted to metallurgical recoveries, which are used to predict the quantity of the final products. The problem stems from the different objectives of the exploration and metallurgical assessment programmes, and is often compounded by the use of different laboratory techniques and mineral definitions. Common mistakes include the misapplication of routine analysis, incorrect interpretation of mineral recovery, the confusion of mineral recovery with product yield and inconsistent definition of the same mineral. Experience has shown that unless these potential mistakes are identified, the measurement techniques used during exploration and metallurgical assessment are not compatible, often resulting in large errors in the prediction of mineral production. There are no easy solutions to the problem, as there is no universal assay technique which can cost effectively characterize all the mineral sands resources. The recommended course of action will therefore require several iterations to optimize the assay technique to suit the resource. Fundamental to the success of the measurement technique is the understanding of the mineralogy, its behaviour during mineral processing and the quality requirements for the final products.

Jan 1, 2003

By M. M. Botz

Cyanidation tailings which are disposed in a surface impoundment experience a loss of cyanide due to natural degradation, frequently reducing the cyanide concentration to very low levels. Quantifying cyanide losses in terms of pond geometry, local weather conditions and feed solution chemistry has been largely empirical though in many cases mining operations rely on surface impoundments to reduce cyanide to below an internally regulated concentration or an effluent limitation. To permit a more quantitative evaluation of cyanide losses in an impoundment, a computer simulation was developed to estimate the losses of free, WAD and total cyanide due to dissociation, photolysis and volatilization. Results of the model are compared against data collected for a North American tailings impoundment during 1998.

Jan 1, 1999

By M. Karmis

Surface subsidence is an inevitable consequence of many underground mining operations and has been recognized as such since the fifteenth century. Damage resulting from this phenomenon ranges from simple land settlement to severe structural damage to buildings and has been witnessed in rural (Illinois, Colorado, West Virginia, Virginia, Pennsylvania) as well as in urban areas (Pennsylvania, West Virginia, Illinois, Wyoming). In fact, it is estimated that over 2 million acres of land across the United States have been affected by mining subsidence, of which 140,000 acres are in urban areas (Singh, 1978; Johnson and Miller, 1979). Further, it is estimated that during the next twenty years an additional 1.5 to 2.4 million acres of land will also be affected by mining. Subsidence prevention is not feasible, at least under the existing technologic and economic constraints of underground coal mining. Foreign experience has demonstrated, however, that subsidence can be successfully controlled if an accurate method of predicting ground movements is available. Such techniques have been developed in many coalfields, where it is currently accepted that subsidence can be predicted within ± 20 percent of the actual values. Furthermore, such movements can be translated into anticipated structural failures using established damage criteria, thus enabling appropriate precautionary measures to be implemented.

Jan 1, 1983

By F. M. Doyle

Metal removal kinetics and metal ion selectivity in ion flotation were studied from a thermodynamic perspective. Surface tension data could be used with the Gibbs adsorption equation to quantitatively predict the metal ion removal kinetics in alkylsulfate-Cu systems. However, surface tensions predicted cation selectivity coefficients in the sodium dodecyl-sulfate (SDS)-Cu-Ca and SDS-Cu-Pb systems rather poorly, although the predicted order of the selectivity (Cu2+<Ca2+<Pb2+) was correct. Another thermodynamic selectivity model, which used the Grahame adsorption equation and a geometrical analysis, predicted cation selectivity coefficients that agreed very well with experimentally measured values.

Jan 1, 2000

By D. Strachan

Installation of support in known poor ground intersections during reaming operations requires rapid access to stabilize the shaft wall and thus to prevent the loss of the shaft through scaling. This is especially relevant to shafts of long dimension where the duration from time of exposure to time of support installation is lengthy This paper deals with the innovative methodology employed at Harmony?s No. 8 Shaft 17/24 level sub ventilation shaft to rapidly support a shale intersection between 23 and 24 Level by employing a single deck stage suspended from the reamer head by means of Skyjack winches.

Jan 1, 2009

By M. Abdelkhalek, M. Hepworth, D. Tao, B. K. Parekh

Pre-combustion coal cleaning and post-combustion flue gas desulfurization (FGD) using lime or limestone are the primary methods employed to reduce sulfur dioxide (SO2) emission from coal combustion. These processes generate voluminous pyrite and gypsum solid wastes that are usually landfilled, occupying thousands of acres of land and creating serious land and water pollution problems due to the release of acids and toxic substances. An integrated process has been developed for the combined utilization of gypsum and pyrite wastes by converting them into useful products including lime, sulfur, and direct reduced iron (DRI). The process includes four major steps. The first step is to concentrate pyrite from coal preparation tailings using flotation or gravity separation. The second is the thermal decomposition of pyrite into pyrrhotite and sulfur. This is followed by the reduction of pyrrhotite with carbon in the presence of lime to produce iron and calcium sulfide. The fourth step involves the reaction of calcium sulfide with gypsum to produce lime. The chemical reactions involved in the process were studied using thermogravimetric analysis (TGA) and X-ray diffraction (XRD)techniques. Process variables studied included reaction temperature, time, reactant composition, and purity of reactants.

Jan 1, 2000

By M. Haase

[ ] How important is a robust communications system for your mine site in order to meet operational and safety requirements? Do you currently have VSAT in place and need a low cost, high quality multi-line VoIP phone system at the site? By adding a single, compact piece of hardware, you can utilize your existing satellite internet connection and have as many as twenty-four separate phones lines from a single unit. The platform is scalable for any size of operation and can be implemented above or below ground.

Jan 1, 2012

By J. H. East, D. Harrington

"INTRODUCTION Mining at its best is not a clean occupation for either surface or underground employees; and this applies alike to coal, metal, and non-metallic mines. The employees are handling minerals that have been blasted, or broken by some means and are subjected to mineral dust, whether it is coal, quartz, or talc. The employees usually wear clothes specifically adapted to the work in which they are engaged, and frequently these clothes are not suitable for use away from the mine. Many mines are wet, and employees must wear rubber boots to remain at least partly dry, and even on relatively dry mines, some parts of the mines usually have water falling from overhead, there are accumulations of water, or the floor or other surfaces are wet or muddy, Some mines are dusty, and the air-borne dust quickly settles on the clothes and body of the miner, especially, when he is working in confined areas, or in places that are hot, humid, or poorly ventilated. Most occupations around a coal tipple, anthracite breaker, or a mill at a metal or nonmetallic mine have their own problems of cleanliness as to skin or clothes or both. Mining in any of its phases is inherently dirty work, and the employees dress accordingly while at work.In the early stages of mining it was the custom or workers to wear their dirty clothes home and change there. This necessitated their going home after work in dirty clothes which were usually damp from perspiration or from contact with wet or muddy matelials or surfaces, and, in addition to being inconvenient this was a frequent cause of colds, pneumonia, other pulmonary diseases or, possible skin ailments. Men working in very wet mines found that it was more satisfactory to change into dry clothes in the boiler room at the mine after work and allow their wet clothes to dry overnight. The mining companies later provided the first of the so-called ""dry-houses"" which were heated but had, few, if any, conveniences, such as showers, lockers, or latrines. The miners changed into dry clothes after work, but would not bathe or ""clean up"" until they reached their homes. Later, progressive mining companies provided bathing facilities for the employees, and eventually the present modern wash and change houses were evolved. Unfortunately, many mines, still have no bathing accommodations, and many have only makeshift accommodations."

Dec 1, 1947

By Oswald J. Heinrich

(with figures on plate V.) THE origin of spontaneous combustion in collieries is, of course, chiefly due to bad system in laying out the pits, unclean workings, insufficient ventilation, and neglect in damming off works after they are exhausted of the main coal. This is particularly indispensable in the Richmond field, because it is difficult and dangerous here, on account of the inferior roof, to remove the last vestiges of coal ; and we are compelled also to retain all the slates and bands, as far as possible, in the pit, to help fill up, although such material is liable to fire. This, however, can be prevented to a great extent, as men¬tioned below. I am satisfied that the only system of working this thick coal is by cross-cutting ( Querbau, ouvrage à travers) or working in benches, as practiced in France (Creusot, Rive de Gier, St. Etienne), in Sile¬sia (Königsgrube), which I have used as far as it is practicable in an old pit, almost torn to pieces by former workings. Modifications may, of course, be needed, even in the same pit, on account of irregu¬larities in the seam. I am also satisfied for economical reasons (on account of the heavy cost for timbering) that pits here ought to be worked upwards, even if it requires a longer period of time to win the coal, and a greater outlay of capital to commence with. The various saddle-shaped "troubles" making natural minor basins in the main basin aid in the execution of this plan. A pit worked once ought to be worked out clean, given up, and dammed off forever. If sections of proper height are assumed, according to the required amount of production for a certain period of time, they ought to be worked out and filled in as much as possible, dammed off, and ulti¬mately allowed to fill up with water, in order to protect the tipper works in future from fire in the gob below. This I consider indispen¬sable, because we may not be able profitably to fill in all the ground. To do so we have to use the waste of the mine, although it is liable to fire in time. In using this stuff, it ought to be surrounded by walls of rock not liable to take fire, laid firmly in clay, the gob being in the middle, and firmly covered and packed with clay on top. In

Jan 1, 1873

Many sampling standards arrive at a value for the prescribed sample mass by assuming a specific relation between the sample mass and the relative standard deviation of the fundamental error and assigning a value to the tolerated coefficient of variation. In order to obtain an equation that provides a relation between the minimum sample mass and the particle properties, many different models for the drawing of a sample have been developed. Here, a model for the drawing of a sample is proposed which can be considered to be a generalisation of the model used in GyÆs sampling theory. Using simulations, it is illustrated that the generalised model can lead to a better correspondence with actual sampling processes.

Jan 1, 2005

By F. T. Cawood

This paper focuses on the role of the coal mine surveyor at the start of the 21st century. It demonstrates that surveyors must look beyond their legal appointment and pursue opportunities to add value at an operational or corporate level of the company. It also exposes the shortfall of statutory appointments in defining the surveyor?s role in terms of key business drivers of the company. One such an opportunity is the potential role of the surveyor in mineral accounting and quality assurance to meet mine requirements, market specifications and standards pertaining to corporate governance and reporting. Finally, some thoughts are expressed on what can be done to elevate current practice to best practice and how to achieve this goal

Jan 1, 2007

Poorly designed sampling protocols generally result in high project risk by artificially increasing grade variability (ie the nugget effect). Sample collection, preparation and assay protocols that suit the ore type, together with QA/QC systems, will reduce this risk. All reporting codes (eg JORC, 2004) require the Competent Person to consider the quality and implication of sampling and assaying programs. High sampling errors beget higher project uncertainty; despite this fact, sampling does not receive the attention it deserves. The case studies presented show that many sampling issues frequently go unrecognised or unaddressed, resulting in poor project decisions during exploration through to feasibility and production. The overall conclusion is that correct sampling is critical to mining project success and that there is often a need for its optimisation.

Jan 1, 2007

By M. J. Lawrence

Independent natural resource Valuers are an essential link between miners and mineral explorers on the one hand and the finance industry on the other. Investors (and regulators) expect the mining and financial industries to be vigilant against the use of inappropriate methodology or use of illogical steps within the chosen valuation method. The Australian Corporations Law generally requires an Independent Expert Report to support mergers and takeovers (as well as for capital raising activities). The introduction of the VALMIN Code (1998) by The Australasian Institute of Mining as Metallurgy, has meant that such Reports, when prepared in compliance with it, are now much more comprehensible and reliable than before. This is because the key requirements of the Code are for transparency and materiality in the Technical Assessment and Valuation Reports prepared in connection with the transaction involved. Transparency is particularly important because it allows the reader to identify and understand the assumptions made to derive a value and to then form a view as to the reasonableness of the result. Even though many elements of resource asset valuation practice are undeniably subjective, there must be some basis of objective rationality to it. Where the reasoning is patently illogical or the inputs are chosen to achieve a particular result, the estimated value must be viewed as virtually worthless. Experience, qualifications, competence and repute are the hallmarks of a professional technical auditor and valuer.

Jan 1, 2000