Search Documents

By C. A. Young, R. G. Robins, E. J. Dahlgren

The formation of copper thio-complexes in sulfide solutions has been recognized for many years and the measured solubilities of certain copper sulfide minerals attributed to these complexes. Attempts to model this system have proposed either copper(I) or copper(II) thio-complexes, and these have been incorporated into computer programs for generating stability diagrams for the copper-sulfur-water system in order to delineate the region where the reductive dissolution of copper sulfide minerals is likely. In this paper it is proposed that the dissolution of copper from both ore bodies and sulfide tailings can be explained by the formation of the cupro-thio-complexes under anaerobic conditions. Stability diagrams are presented to depict the region and extent of the solubility.

Jan 1, 2001

By [D. N. ] Naresh

During different activities pile installation like pile boring, concreting etc., it is likely that various problems, depending up on site condition may be encountered. There are possibilities that some of the activities if not correctly followed may affect the pile capacity. This paper describes few problems encountered during pile execution at different sites and presents the remedial measures undertaken to overcome them.

Jan 1, 1996

By George K. Burke

Single axis soil mixing is a mechanical method of blending soil in situ with a reagent binder to achieve improved character. Generally this achieves a design compressive strength or shear strength and/or permeability, but can be used to immobilize and/or fixate contaminants as well as a treatment system for chemical reduction to a more "friendly" substrate. The reagent binder can be a variety of materials, including cement, fly ash, slag, lime, and an assortment of additives. Usually this reagent is delivered in a slurry form (combined with water), but the Dry Mix Method uses pneumatic conveyance.

Jan 1, 2001

By John J. Mulligan

The Bureau of Mines investigated the tin deposits of the Cape Mountain area during July and August 1962 to test the effectiveness of detrital-cover sampling in permafrost areas as a relatively cheap and simple means of guiding mine development and exploration. Results indicate that systematic detrita1-cover sampling can be used effectively to delineate obscure deposits with sufficient accuracy to permit sampling with a minimum of trenching or drilling. Extensions of known outcroppings were traced in sufficient detail to guide lode sampling and several previously unknown tin-bearing lodes were found and sampled. Lode sampling was limited to the minimum needed to establish the reliability of detrital-cover sampling results. The results of previous lode and placer investigations are summarized and detrital-cover sampling methods and results are described in detail.

Jan 1, 1966

By L. Gertsch, R. Gertsch

Mechanical mining is steadily gaining usage in the mining industry. A variety of machines currently finds employment: tunnel boring machines, roadheaders, continuous miners, surface miners, and augers. These machines have advantages compared to drill and blast mining methods, including increased safety, lower cost, uniform muck size, and accurately sized openings. A century of experience with mechanical methods has already paid dividends to the coal industry. Current trends guarantee eventual development of true general-purpose hardrock mechanical mining machines. Mechanical miners will become integrated mining systems and will determine the design of mines, when several significant challenges have been met.

Jan 1, 2001

Rising energy costs are a growing concern among mine operators. At sur’ace operations, the size of a dragline, production requirements, pit geometry and layout, and operator skill are all factors in potential energy savings. The following tips are offered as a practical means to conserve energy demand, and can be applied to diesel fuel draglines as well.

Jan 7, 1980

By E Westthorp, J Phillips

The detection of ethylene in mined-out ‘goaf’ areas of underground coalmines is an industry standard indicator of accelerated oxidation where the coal temperature has exceeded 100°C. If uncontrolled, this naturally occurring process can lead to spontaneous combustion and catastrophic mine explosions, such as the Moura No 2 mine explosion. Spontaneous combustion trigger action response plans (TARPs) typically use the detection of ethylene as a trigger for definite change requiring immediate reaction, which can include the withdrawal of coalmine workers.Following the completion of sealing of longwall goaves at Crinum North Mine, ethylene was often detected in trace quantities. These trace quantities were below 1 ppm and detected via the bag sampling regime, with the use of a gas chromatograph. Any ethylene detected in these instances was not associated with increased quantities of carbon monoxide to conclusively indicate a heating within the sealed area.Ethylene was only detected in a newly sealed goaf and would not remain present for a period following the sealing. As part of the longwall recovery process, the predominant roof support mechanism during the recovery was the use of timber cribs. It was decided to investigate the possibility of this timber generating ethylene.Preliminary tests were completed by placing timber specimens from several species of Australian native hardwoods in gas bags in air. Over time, some of the samples showed significant levels of ethylene within the bags.CITATION:Westthorp, E and Phillips, J, 2017. Findings from preliminary testing to determine alternative sources of ethylene within sealed areas of underground coalmines, in Proceedings Australian Mine Vent Conference 2017, pp 203–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By S. K. V. Avasarala

This paper presents a case history of design, prediction, probe and production pile driving monitoring, loading tests and installation of over 3,300 prestressed concrete piles for a building complex consisting of 12, 5- and 6-story over parking buildings. The project was recently completed in three-phases over a span of 4 years. The subsoil conditions were explored by performing 25, Standard Penetration Test (SPT) borings throughout the site. Various types of driven pile foundations were considered and following an evaluation of high structural loads and site-specific constraints such as variable depth of bearing layer of Florida limestone and quality of clay and limestone layers, a prestressed concrete pile support system was selected as the most economical and effective foundation approach. The building foundations were designed for a pile capacity of 353 kN (40 tons) in compression, 45 kN (5 tons) in lateral capacity for a deflection of 0.64 cm (0.25 in.), and 133 kN (15 tons) in uplift capacity. The axial and lateral allowable pile capacity and lengths were predicted using SPT91 and LPILE computer programs, which are generally used in Florida. The validation of these capacities was derived from 144 probe piles and performance of 12 pile loading tests on selected probe piles. Prior to installation of probe or production piles, a termination criterion was established using 1-dimensional wave equation analyses in addition to the design pile embedment requirement. The predicted pile capacities compared very well with the capacities from the loading tests on probe piles. This information was effectively utilized as part of the overall quality control program to install a total of 4,186 prestressed concrete piles (including 144 probe piles) in different building areas across the project site to depths ranging from 8 to 21 m (25 to 90 ft) below existing ground elevation as part of foundation support system. This engineered, monitored, and tested foundation solution provided an effective and satisfactory basis for completion and approval of the foundation work for this 12, 5- and 6-story over parking building complex. A recent reconnaissance has indicated that all the building foundations are performing satisfactorily.

Jan 1, 1995

By Asmo Vartiainen

Background of Direct-to-Blister Flash Smelting is discussed; especially slag chemistry relating to copper solubility, slag fluidity and impurity behavior. In December, 2000, Mini-pilot Flash Smelting test runs were carried out at Outokumpu Research Oy to produce blister copper from Chilean concentrate and white metal and from a mixture of them. Tested slag types were iron silicate slag, ferrous calcium silicate slag and calcium ferrite slag with different slag compositions and different concentrate/white metal ratios. The test runs were successful. The fluxing effect of copper oxide was clearly demonstrated and ferrous calcium silicate slags remained fluid on a very wide liquidus range. The distribution of arsenic between ferrous calcium silicate slag and blister copper is much higher than between iron silicate slag and blister copper. This successful test run with the new slag type offer new possibilities in Direct-to-Blister process design.

Jan 1, 2003

By Richard Curtis

Optimum Colliery is presently experiencing a shortfall of stripping capacity in order to meet its production requirements. Due to the long dragline procurement times, several alternative stripping methods were evaluated in order to alleviate this shortfall in the interim period. Based on the experience gained at the mine. The writer will discuss some of the important factors which influence dragline performance and show how these factors may by used in a theoretical approach to analyse various dragline applications.

Jan 1, 1990

By Drupad B. Desai, Bruce Chang, Jay L. Merritt

This paper reviews difficult ground conditions encountered along the alignment of large-diameter sewage tunnels for the City of Los Angeles. It offers a detailed one-of-a-kind solution to a unique problem for shallow urban underground tunnels in a seismic zone, using state-of-the-art materials, technology, and equipment. The following topics are discussed in detail: • Geotechnical Design consideration for tunnel traversing through an active fault zone. • Seismologist evaluation of possible fault-offset problems where a fault zone crosses the alignment, in the event of an earthquake of moment-magnitude 6.5. • Probability analysis regarding "recurrence interval." • Structural design of tunnel subjected to displacement, subjected to axial elongation or shortening, and capable of rotational freedom. • Special joint details.

Jan 1, 1989

By S. G. Malghan, J. P. Van Dillen

Introduction Some uranium minerals are paramagnetic and hence are amenable to concentration by high gradient magnetic separation (HGMS). This paper describes effects of the HGMS parameters-pulp velocity, field strength, matrix loading, and magnetic field gradient-on the product recovery and grade. Unsatisfactory separation of uranium minerals by HGMS is related to ore-specific properties, such as lack of liberation, fine dissemination of uranium minerals, uniform distribution of magnetic minerals throughout the ore matrix, and interference of fine-sized slimes. Experimental techniques to identify and resolve some of these problems are outlined. HGMS of Uranium Ores The mechanism by which uranium minerals are attracted to a magnetic field is either due to its magnetic susceptibility or its association with other minerals that are magnetic. Data on magnetic susceptibility of uranium minerals are scarce. The only reported data are for uraninite at 2360 X 10-6 cm3/mole. Povarennykh (Andres, 1976) concluded that the magnetic properties of minerals depend on: • Structure of the outer electron shell in a mineral with electropositive atoms; • Valence of the atoms; • State of the chemical bonds; • Type of coordination; and • Proportion of magnetic atoms (Fe, Mn, Cr, and Ni) in the composition of the mineral. However, information on the magnetic susceptibilities of the constituent atoms of a mineral alone does not suffice for evaluating the mineral compound as a whole. Most often, uranium minerals can be beneficiated by HGMS if they are associated with other minerals that are magnetic. This appears to be a more predominant mechanism by which the uranium minerals are beneficiated. Experimental A Sala-HGMS (Malghan and Subramanian, 1981), model 10-15-20, separator was used in the experiments. The matrix material-ferromagnetic stainless steel in the form of expanded metal or steel wool-was packed into a 38-mm (1.5-in.) diameter by 360-mm (14-in.) long canister. The matrix material occupied only a 150-mm (6-in.) length. The experimental set-up and slurry flow direction are described elsewhere (lannicelli, 1976). The response of uranium ores in the HGMS was studied by feeding well-dispersed slurry at 10% solids and examining the influence of process variables on selectivity and overall uranium recovery. The chemical and mineralogical characteristics of the ores under study are presented in Table 1.

Jan 12, 1983

By Xu Youzai

Static loading teets of five nodular piles and four non-nodular piles were performed in Tianjin soft clayey soil in which measurements of axial force and movements were made. Distribution of shaft resistance and load-movment curves for pile head and pile toe are presented in this paper. The applicability of nodular piles to soft soil and their effectiveness are also discussed. Based on the comparison, it is concluded that nodular piles have an advantage over non-nodular piles mainly in contri­bution to shaft resistance. Dynamic testing was also conducted through R. P. T. for evaluating the service load of tested piles.

Jan 1, 1991

By Pan Shisheng

Amodified load transfer method computing the displacement, axial compression, skin resistance, toe resistance, and other static bearing behaviours of piles, is propoesd in this paper. Through deriving a new concrete computational method with simple integration, many complex factors, such as different soil properties of each layer in layered soil, variation of soil parameters with the changes of the depth, different elastic moduli of piles under different loads, and even different areas in the same pile, can all be easily considered. This method fits in with many types of piles, including friction and point bearing piles, precast and cast-in-situ piles. Observation of static loading test on pile is given, and the computed values from the modified load transfer method are found to agree with practical measured results.

Jan 1, 1991

Jan 1, 1968

By P. Ashayer, J. Curran

Introduction Rockfalls occur when rocks or boulders detach from mountains or hills and tumble down. They can pose significant hazards to infrastructure such as highways, buildings, and mine open pits, and they sometimes result in personal injury or death. Prediction of rockfalls is a difficult task. Slopes that are at risk of rockfall have highly variable geometries. The location, mass, and shape of the rocks that might dislodge and fall are uncertain. Moreover, the materials that make up a slope can vary considerably from one section to another. Furthermore, the relevant material properties are usually not well known. Performing probabilistic simulations of rockfalls, combined with proper statistical analyses, has proven to be an effective and acceptable method for dealing with these difficulties [1, 2, 3]. The movements of a falling rock can be classified as freefall, bouncing, sliding, toppling, or rolling. The falling trajectory is controlled mainly by the geometry of the slope, the block shape, and the energy dissipated at each contact of the block with the slope. A rockfall model is evaluated based on its ability to efficiently predict the velocity, frequency, height of bounce, and run-out distance of falling rocks. With this information, the engineer can design remedial measures such as restraining nets and ditches. Most of the existing rockfall simulators are based on particle models that consider the falling rock as an infinitesimal particle with a mass, called the lumped mass or stereomechanical models [1, 2, 3, 4]. Other models involve hybrid methods relying on simplified assumptions. The most common hybrid methods are based on contact searching for the movement of a dimensionless object and incorporate some aspects of rigid body impact for bouncing [5, 6, 7]. There are also some rigid body models in the literature that employ simplified versions of rigid body models [8, 9]. This study applies a more sophisticated rigid body theory based on rigid body impact mechanics (RBIM), which was developed by Stronge [10, 11, 12]. The new theory captures all modes of rigid body movement. Due to the importance of the rock geometry, single impacts of ellipsoidal and prismatic rocks with rectangular cross sections are investigated. The effect of rock slenderness on rebound velocities and energies is also investigated for ellipsoidal rocks. The correspondence between the model parameters and the data from the rockfall literature data will be discussed.

Jan 1, 2007

By E. R. Darby

When bronze is melted in open-flame furnaces a considerable amount of slag is formed during the melting operation. This slag may be incidental to the melting practice or it may be formed intentionally by slag-forming constituents added to the furnace charge to provide a covering for the melted metal When this slag is removed from the furnace, it contains, in addition to the free metal carried with it by the skimming operation, a considerable amount of metal as oxide either combined or mechanically mixed with it. By the usual crushing and washing methods this metallic oxide generally goes to the tailings pile, so diluted by other foundry waste that its recovery is economically impossible. If this furnace slag is not inixed with other foundry waste, practically all of the metal oxide as well as the free metal may be recovered by some form of smelting operation. The first side of the problem to be considered is the amount of slag produced. It may not be true that the majority of foundries have no record of the amount of slag made, but it is certainly true that a very great many either have no record or pay little attention to it. Usually the collection of furnace slag for one normal week's run will be sufficient to determine the advisability of its being handled in a different manner from the crushing and concentrating generally employed. If a large representative sample of the accumulation is crushed and concentrated and the recovery compared with the results of a careful assay, it will be found that a large percentage of the total metal content was lost in the washing process. The percentage of loss will be greater than the metallic oxide content, as some free metal in extremely fine particles always is carried away in grains of slag. From such a comparison, it may be determined whether or not the slag should be melted, sold or treated as before. An example of an actual test of this kind is given below. In a foundry melting 50,000 to 80,000 Ib. of bronze per day, a week's accumulation of furnace slag and ladle skimmings amounted to 16,500 1b.—over three times as much as the foundry superintendent estimated before the accumulation was made. Two tons of this material was taken as representative of the lot. This was ground through a thoroughly cleaned ball-mill and concentrated over a Wilfley table. The

By J. R. Yates, R. J. Young, G. E. Forward, J. B. Farrell, R. J. Milbourne

"Sustainable development in the mining and metallurgical industrial sectors can be implemented by two distinct groups: the managers and operators of existing facilities, working with industrial processes and systems that have been operating for many years, in some cases, several decades; and those who are engineering and building new facilities or upgrades of existing plants.The focus of this paper is to look at approaches and tools available to bring sustainable development thinking and action to these two distinct areas. The paper will discuss the concept of working with existing facilities and processes to minimize waste and maximize product from a regional raw material/resource consumption perspective using by-product synergy. The BPS concept has been carried out in Texas (e.g., TXI-Chaparral’s STAR), in Calgary, Alberta, with Suncor assistance, in Montreal, Quebec, with Noranda as project leader, and currently in Ontario with Dofasco as industry champion. Successful outcomes are presented. The paper will also discuss a new approach to designing greenfield facilities or upgrades to existing plants using a sustainable development review process. Undertaking the review early in every project can institutionalize the concept of discussing and implementing waste elimination, design for environment, ecoefficiency, risk minimization and community awareness and involvement in the future capital stock. The review process has been developed as an excellent tool for measuring and reporting on a corporation’s sustainable development progress. Examples of how this approach has been adopted in the mining and metallurgical industry, and the resultant outcomes are given."

Jan 1, 2003

By A. E. Koski

Two of the largest industries in northern Michigan, pulp and paper manufacturing and iron mining, formed a mutually beneficial partnership and collaborative research program to utilize paper mill residuals for waste rock stockpile reclamation. Historically, the majority of the paper industry’s residuals have been disposed of in landfills. The beneficial use of paper mill residuals for mine reclamation provides an environmentally sound recycling solution for the solids generated at northern Michigan paper mills and eliminates the need to strip additional overburden (glacial till) for final mine reclamation. Residuals offer a cost-effective source of organics and nutrients necessary for successful reclamation and waste rock stockpiles offer an economical and environmentally sound solution for disposal of residuals. The goal is to successfully pioneer technical development of paper mill residuals to accomplish vegetation of steep waste rock stockpile slopes and benches to establish a self-sustaining plant community that meets final reclamation requirements. Of the various types of iron mining wastes, rock stockpiles pose the greatest reclamation challenge. Success depends on incorporating sufficient organic matter into the rock stockpiles to produce a growth medium that can sustain vegetation without the need of overburden. This is an ongoing research program that is evolutionary in nature with numerous field trials, greenhouse studies, data collection and monitoring over multiple growing seasons. The program is a combination of innovative ideas and accepted reclamation practices that is proving to be a beneficial and economic approach to paper mill residual management and mine reclamation that will eventually lead from research to standardized reclamation procedures.

Jan 1, 2006

By Hideo Ando, Yuka Satou, Tatsuya Ishitake

Whole-body vibration occurs when the body is supported on a surface which is vibrating. Occupational exposures to whole-body vibration mainly occurs in the transportation industry, but also in association with other industrial process. Epidemiological studies have frequently indicated an elevated health risk for the spine in workers exposed to whole-body vibration. With regarding to train or bus operators, a fall of drivers’ wakefulness level because of fatigue is often pointed out. This decrease in wakefulness results in an increase of the occurrence of accidents. However, a study of how whole-body vibration affects people's level of wakefulness has not been done. To test the hypothesis that exposure to whole-body vibration has a certain effects on level of wakefulness, the change of a subjective wakefulness level and changes of electroencephalogram (EEG) were observed under experimental exposure to short-term whole-body vibration. Methods Subjects are ten healthy male university students, with an average age of 20.7 ± 1.8 years old, and they are all nonsmokers. Using the equipment (CV-300, AKASHI) of whole-body vibration generator, we consider an exposure environment of actual driver work, so that set the frequency and the acceleration level as 10 Hz and 0.6ms-2 r.m.s.. The subjects were exposed to whole-body vibration in the seated position and exposure time was fixed for 12 minutes. Subjective wakefulness level was evaluated using the questionnaire of VASS (Visual Analog Sleepiness Scale) and KSS (The Kwansei Gakuin Sleepiness Scale). For the electroencephalogram (EEG) measurement, it was equipped with the electrodes based on the International ten-twenty electrode system (C3-A2, O1-A2, O2-A1). EEG activity in the alpha frequency band (8 – 12 Hz) is one of the most typical physiological indicator which represent the transition from wakefulness to sleepiness. AAT (Alpha Attenuation Test) which repeats three times each opened and closed eye for 1 minute was performed in a seating position with directions of the researcher in the beginning, in the middle and in the end of exposure to whole-body vibration. For analysis, power spectral analysis was conducted over the last 6 min of EEG, and wakefulness levels were defined as the ratio of mean alpha power during eyes closed versus eyes opened. The laboratory was kept at room temperature (21 ± 1.0 degrees C), humidity was 50 ± 5%, noise level was 63.6 dB (A) eq, and illumination 510 lx. Each experiment was started around 10:00 am to minimize the effect of biorhythm.

Jan 6, 2006